* blink, fp should not be always cleared
* clean up code format
* use a better way to save and restore ER_SEC_STAT
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* current codes use a faked interrupt return to do a thread switch
in exception return.
* so the different between exception return and interrupt return
should be carefully considered.
* when secure is enabled, the sec_stat should also be pushed in
exception entry.
* when secure is enabled, SEC_STAT.IRM must be configured corrrectly
for interrupt return.
* For the case of faked interrupt return in exception return, the
correct value of SEC_STAT.IRM comes from ER_SEC_STAT.ERM.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The PPB, Peripheral, and any other I/O regions have been
removed, the Shareable options are only important with
unlocked dual cores. Just use the background mapping,
which is RWX for supervisor and no access for user mode.
The flash region needs to be kept to indicate read-only
policy. The RAM regions need to be kept to disable execution.
Fixes#6896
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The PPB and Peripheral regions have been removed,
the Shareable options are only important with unlocked
dual cores. Just use the background mapping.
The flash region needs to be kept to indicate read-only
policy. The RAM regions need to be kept to disable execution.
Related to #6896 and #7877
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In order to mitigate against Spectre V4, add an option that will, at
boot time, verify if the CPU supports the SPEC_CTRL MSR; if so, it'll
attempt to disable the feature.
More information can be found in chapter 4 (Speculative Store Bypass
Mitigation) of the "Speculative Execution Side Channel Mitigations"
document, version 2, published by Intel: https://goo.gl/nocTcj
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The STM32L432 SoC has a standard non-OTG USB controller. Add an entry
for it in stm32l432.dtsi and add the corresponding DTS fixup entries.
The controller is kept disabled and should be enabled at the board
level.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
USB OTG is currently enable for the whole STM32L4 family, while only a
few of them actually support it:
- STM32L475, STM32L476 and STM32L496 have an OTG controller
- STM32L432, STM32L433 and STM32L452 have an USB controller
- STM32L431, STM32L451 and STM32L471 do not have any USB controller
Fix that by moving the DT entry from stm32l4.dtsi to stm32l475.dtsi
and by adding a #ifdef #endif around the corresponding DTS fixup
entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When the RTC support get added we had a select on HAS_RTC, however this
Kconfig symbol didn't exist. Clean this up to match the pattern of
HAS_MCUX_RTC. The driver now depends on that and the SoC selects it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
gdb_server was removed in commit 0f669132a0 ("kernel: remove
gdb_server"), but still has a testcase that sets CONFIG_GDB_SERVER=y,
and some code in arch/x86/debug.
Remove the leftover parts. This also gets gets rid of undefined
references to the CONFIG_GDB_SERVER symbol.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Some code was developped around MPU support in ealy stage
of feature introduction. This code was gated under MPU_ENABLE
flag which does not exist and hence code has never been
enabled nor tested.
Since there has been futher MPU development since then, it seems
safer to simply remove that code and associated Kconfig symbols
to avoid that someone starts using it while it was not part of
MPU development track.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename _MsrRead() and _MsrWrite() to _x86_msr_read() and
_x86_msr_write() respectively.
Given that these functions are essentially implemented in assembly.
make them static inline. They can be inlined by the compiler quite
well, most of the time incurring in space savings due to better
handling of the cobbled registers.
Also simplifies the inline assembly, using constraints instead of
moving registers ourselves. Should shave off a few bytes from code
using these functions.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Remove unused context switch code from the helper assembly file that
manages the SuperVisor Call invocations (SVCs). This is no longer in use
in the code, since all calls to __swap() now go through PendSV directly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The initial user stack pointer gets rounded to STACK_ALIGN_SIZE,
which can be much finer granularity than MPU regions. With
certain stack size values passed to k_thread_create(), the stack
pointer can be set past the defined region for the user thread's
stack, causing an immediate MPU fault.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Upon return from a syscall handlers, the r1, r2, and r3 registers
could contain random kernel data that should not be leaked to user
mode. Zero these out before returning from _arm_do_syscall().
Fixes#7753.
The invocation macros need a clobber if r1, r2, or r3 are not used
to carry syscall arguments. This is a partial fix for #7754 but
there appear to be other issues.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The Kconfig option TOOLCHAIN_VARIANT (not to be confused with
ZEPHYR_TOOLCHAIN_VARIANT) is a legacy configuration option that has
very few use-cases and can easily be dropped.
It's functionality is easily covered by CONFIG_X86_IAMCU and
ZEPHYR_TOOLCHAIN_VARIANT.
This commit removes all references of it from Zephyr.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
patch add clock frequency and interrupt property to uart
node in intel_s1000.dtsi. Include soc.h after types.h to
prevent build error.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Recent change to RTC core now gets CONFIG_RTC_0_NAME from device tree.
So we need a fixup for KW41Z for that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The kl25z does not have the same spi hardware as the k64f and therefore
cannot use the same spi driver. Remove all references to spi for the
kl25z soc and frdm_kl25z board until we have a valid spi driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fix the qmsi i2c driver and the relevant SoCs accordingly.
Also applying relevant changes on quark_se_c1000_ss as it can use i2c
qmsi driver as well along with qmsi ss i2c driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that all arch using QMSI gpio driver are generating the right
settings through DTS, these options can be removed from Kconfig.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix the ns16550 uart driver and relevant SoCs accordingly.
All generic settings are now DTS based.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix the qmsi uart driver and relevant SoCs accordingly.
Also: using config for irq everwhere relevantly and not an hardcoded
value in the driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Get the name generated through dts as well.
Fix the rtc driver and relevant SoCs accordingly.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Get the name and irq flags generated through dts as well.
Fix Kconfig for the gpio driver accordingly.
Irq priority is not set by dts for D2000 as it's irq controller does
not support it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add IEEE 1003.1 Posix Style file system API support.
These API's will internally use corresponding Zephyr
File System API's.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
This commit gets rid of the 'option env="ENV_VAR"' bounce symbols.
"$FOO" now expands directly to the value of the environment variable
FOO, instead of to the value of the Kconfig symbol FOO.
This change is likely to soon appear in the C tools as well. Those
'option env' symbols always seemed kinda pointless, and have broken
dependency handling due to forcing symbol evaluation during parsing,
before all the symbols have even been seen.
Compatibility with the C tools could be retained by naming all
'option env' symbols the same as the environment variable they
reference.
This commit also updated the Zephyr documentation to explain the new
behavior. It's relevant for $ZEPHYR_BASE and out-of-tree Kconfig
extensions.
Commit message from Kconfiglib (cbf32e29a130d)
==============================================
Make "$FOO" directly reference the environment variable $FOO in e.g.
'source' statements, instead of the symbol FOO. Use os.path.expandvars()
to expand strings (which preserves "$FOO" as-is if no environment
variable FOO exists).
This gets rid of the 'option env' "bounce" symbols, which are mostly
just spam and are buggy in the C tools (dependencies aren't always
respected, due to parsing and evaluation getting mixed up). The same
change will probably appear soon in the C tools as well.
Keep accepting 'option env' to preserve some backwards compatibility,
but ignore it when expanding strings. For compatibility with the C
tools, bounce symbols will need to be named the same as the environment
variables they reference (which is the case for the Linux kernel).
This is a compatibility break, so the major version will be bumped to 6
at the next release.
The main motivation for adding this now is to allow recording properties
on each MenuNode in a clean way. 'option env' symbols interact badly
with delayed dependency propagation.
Side note: I have a feeling that recording environment variable values
might be redundant to trigger rebuilds if sync_deps() is run at each
compile. It should detect all changes to symbol values due to
environment variables changing value.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add driver for MCUX mailbox which can be used for lpcxpresso54114
and other lpc and kinetis socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Added ability to load and bootup the slave (Cortex-M0+) core on the
LPC54xxx SoC. Currently we expect a binary image to be specified via
Kconfig for the code that will run on the slave core. We also specify
via Kconfig the boot/load address for the slave core.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add soc configuration support and dts files for nxp_lpc54xxx_m0.
Adjusted nxp_lpc54xxx soc, configuration and dts files for the
presence of slave core.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds the configuration, driver, and HAL changes required
to implement a MCUX based RTC driver for the NXP Kinetis KW41Z.
Signed-off-by: Andy Gross <agross@kernel.org>
This patch adds some DTS information to flesh out the NXP Kinetis
based RTC blocks. DTS fixups were added as well to match up the driver
usage to the DTS output.
Signed-off-by: Andy Gross <agross@kernel.org>
Declare and implement convenience wrappers to evaluate read and
write permissions of C variables using the cmse address range
intrinsics.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes the implementation of the
CMSE address range permission checks based on the
ARMv8-M address range check intrinsics.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Select CPU_CORTEX_M_HAS_CMSE in ARMV8_M arhitectures.
Option ARMV8_M_BASELINE is introduced for this purpose,
so that CMSE API is enabled for both Cortex-M23 and
Cortex-M33 MCUs.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit defines and implements an internal ARMv8-M API
that allows the user to evaluate access permissions of memory
locations, based on the ARMv8-M Test Target (TT) instruction
support.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Dynamic kernel objects no longer is hard-coded to use the kernel
heap. Instead, objects will now be drawn from the calling thread's
resource pool.
Since we now have a reference counting mechanism, if an object
loses all its references and it was dynamically allocated, it will
be automatically freed.
A parallel dlist is added for efficient iteration over the set of
all dynamic objects, allowing deletion during iteration.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The interrupt stack area wasn't being set to a repeating
0xAA pattern at boot as it should be. This is now done in
kernel_arch_init(), which runs before interrupts are
enabled for the first time.
Fixes#7327
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Kconfig keyword GPIO_AS_PINRESET is common for whole nrf52 series.
This patch move it to the series Kconfig.soc file.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
It is possible to use NFCT pins as regular GPIOs.
This patch introduce option for enabling this feature.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Enabling the driver on board level is sufficient. We need to find a
better way for selecting random drivers on SoC level, this is currently
not possible due to how Kconfig works.
Fixes#7097
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The instructions performed by standard Zephyr startup files are removed
from the file startup_LPC54114_cm4.S. Introduced the section
_PlatformInit which will be called when platform specific initialization
is needed.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Rename various SoC related defines and files from just being LPC54114
to LPC54114_M4. This is in prep for supporting a build for the second
core on the LPC54114 (the Cortex-M0+).
* Renamed Kconfig SOC_LPC54114 to SOC_LPC54114_M4
* Renamed Kconfig.defconfig.lpc54114 to Kconfig.defconfig.lpc54114_m4
* Introduced nxp_lpc54xxx_m4.dtsi based on nxp_lpc54xxx.dtsi
* Moved some pinmux related defines into SoC code.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the ability to call platform specific code as the first thing we do.
This is needed because on some platforms we might have to figure out how
to deal with starting up secondary cores and need to do that as the
first thing we do.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Normally a syscall would check the current privilege level and then
decide to go to _impl_<syscall> directly or go through a
_handler_<syscall>.
__ZEPHYR_SUPERVISOR__ is a compiler optimization flag which will
make all the system calls from the arch files directly link
to the _impl_<syscall>. Thereby reducing the overhead of checking the
privileges.
In the previous implementation all the source files would be compiled
by zephyr_source() rule. This means that zephyr_* is a catchall CMake
library for source files that can be built purely with the include
paths, defines, and other compiler flags that all zephyr source
files uses. This states that adding one extra compiler flag for only
one complete directory would fail.
This limitation can be overcome by using zephyr_libray* APIs. This
creates a library for the required directories and it also supports
directory level properties.
Hence we use zephyr_library* to create a new library with
macro _ZEPHYR_SUPERVISOR_ for the optimization.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Distinguish between the integrity signatures depending on whether the
ARM MCU implements the Floating-Point Extension or not.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit partially reworks the fault dump implementation
of faults in non-secure state that target Secure state. In
particular, the return address to secure state is logged along
with the non-secure address which caused the non-secure fault
(that targets the Secure state).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Fix bug when setting SCB_AIRCR during initialization; add
Vector Key to permit write to AIRCR fields.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes the Secure fault handling for ARMv8-m
implementations, that do not support the Main Extension, such
as the (Baseline) Cortex-M23 processor.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
it seems regular expresssion is not supported in "source xxx" after
latest changes in build system.
So explictly list all def config
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* add gpio, i2c, spi definitions
* optimize and bug fix the dts.fixup
* optimize and bug fix the em_starterkit related definitions
in dts folder
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The original em7d, em9d and em11d are different configurations of
em_starterkit. They have the same peripherals, e.g. uart, spi, gpio
, ddr. The differences of them are in arc core configurations, interrupt
number assignment.
So em7d, em9d and em11d can be viewed in the same SoC family or SoC
series.
Referring other arch's implementation, this commit merges em7d, em9d
and em11d into the same SoC, named snps_emsk. This will eliminate
unnecessary duplication and make it easier for future maintainment.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
patch removes Kconfig defines for RAM and ROM size in x86. Instead
these values are derived from dts.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Commit introduces support for watchdog configuration for Nordic
Semiconductor nRF SoCs in device tree.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Enable System Configuration Controller clock in clock_control
instead of gpio controller when we set a gpio as interrupt.
We use System Configuration Controller to manage external
interrupts and enable PIN pair PA11/12, used in USB device,
mapped instead of PA9/10.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Enable System Configuration Controller clock in clock_control
instead of gpio controller when we set a gpio as interrupt.
We use System Configuration Controller to manage external
interrupts and internal voltage reference for 48 MHz HSI
used in USB device.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
STM32Cube HAL core initialization functions HAL_GetTick()
and HAL_Delay() are implemented in all STM32 series. This
patch moves these functions in file stm32cube_hal.c under
"common" folder to reduce code duplication.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
MPU devices that enforce power-of-two alignment now
specify the size of the buffer used for the newlib heap.
This buffer will be properly aligned and a pointer
exposed in a kernel header, such that it can be added
to a user thread's memory domain configuration if
necessary.
MPU devices that don't have these restrictions allocate
the heap as normal.
In all cases, if an MPU/MMU region needs to be programmed,
the z_newlib_get_heap_bounds() API will return the necessary
information.
Given how precious MPU regions are, no automatic programming
of the MPU is done; applications will need to do this as
needed in their memory domain configurations.
On x86, the x86 MMU-specific code has been moved to arch/x86
using the new z_newlib_get_heap_bounds() API.
Fixes: #6814
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Adds dts bindings for the mcr20a wireless transceiver. The frdm_k64f
board supports the mcr20a via an Arduino shield, therefore the dts node
is added to the board dts. The kw2xd is a SiP and thus the mcr20a dts
node is added to the soc dts.
The networking samples using prj_frdm_k64f_mcr20a.conf have been broken
since the refactoring of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The kw40z and kw41z socs have the same dspi peripheral as the k64 and
kw2xd, so we can reuse the existing mcux dspi shim driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
With recent dts script change we dropped _0 from define names if there
is only a single one. So for the MPU we need to use
CONFIG_SRAM_BASE_ADDRESS instead of CONFIG_SRAM_BASE_ADDRESS_0.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When we included SoC specific Kconfig files we do something like:
gsource "arch/arm/soc/arm/*/Kconfig.soc"
However, we should do that inside an if block for that SoC family so as
to limit SoC family specific options to only being visible when that SoC
family is selected. So we simply move the gsource and related items
inside the if SOC_FAMILY_<SOC> block.
Fixes: #7452
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In order to disable the execution of code from the RAM region
we need to declare it in arm_mpu_regions.c file.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
In dts.fixup files for used for NXP SoCs, IP clock name was
bound to SIM clock label. This is correct but would require
manual change if IP clock controller was changed in device tree.
Use reference to IP generated define "_CLOCK_CONTROLLER" to get
this value.
Besides, having all IP related values starting with the same prefix
will be easier for possible macro preprocessing (if required one day).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
'cell_string' yaml attribute has been introduced in order to
help enforcement of specific string during defines generation.
This adds complexity in understanding script behavior as a black
box and create additional dependency which is not strictly required.
For node specific generation functions (pinctrl and interrupts),
this could be replaced directly by an hardcoded version
(as everyone used the same 'cell_string' anyway).
For extract_cells functions, string could be replaced by extracted
property name. As a consequence, we're now able to generate defines
for properties refering to these controllers via phandle.
For instance, in following node
spbtle-rf@0 {
compatible = "st,spbtle-rf";
reg = <0>;
reset-gpios = <&gpioa 8 0>;
};
We'll be able to generate:
#define ST_STM32_SPI_...LE_RF_0_RESET_GPIOS_CONTROLLER "GPIOA"
#define ST_STM32_SPI_...PBTLE_RF_0_RESET_GPIOS_FLAGS_0 0
#define ST_STM32_SPI_..._SPBTLE_RF_0_RESET_GPIOS_PIN_0 8
Only impact for this whole change is for NXP clocks which were the
only ones using 'cell_string' attribute with a value different than
the default one.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Indexed defines were systematically generated even when there
was only one element to generate.
So we ended up generated a lot of _0 defines.
Then we needed to generate aliases to these _0 indexed defines,
in order to get useful defines.
For instance:
#define GPIO_LEDS_0_GPIO_FLAGS_0 4
#define GPIO_LEDS_0_GPIO_PIN_0 5
#define GPIO_LEDS_0_GPIO_FLAGS GPIO_LEDS_0_GPIO_FLAGS_0
#define GPIO_LEDS_0_GPIO_PIN GPIO_LEDS_0_GPIO_PIN_0
This commit allows to generate _0 indexed define only if a
property has more than one elements to define.
Aliases generation to _0 indexed defines are also removed.
Note: IRQ are left untouched since this is frequent to handle
multiple IRQs in a driver
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit implements consistency checks for the core registers
in ARMv6-M, ARMv7-M, and ARMv8-M architectures, ensuring that
the user cannot accidentally select registers that are not
implemented by the selected Cortex-M processor.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The commit improves the help text of the ARMV7_M_ARMV8_M_MAINLINE
K-config option.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds a Context Synchronization Point immediately
after the reset handler switches to use the Process Stack
Pointer, during initialization.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Adds 8 MB and 64 MB flash size options, which correspond to the two
external flashes (qspi flash and hyperflash) on the mimxrt1050_evk
board. Adds a 32 MB SRAM size option, which corresponds to the external
sdram on the board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The API in the current SDK version is rom-patched, and uses
prcm.c code in the driverlib directory.
But, the PRCMMCU3200Init() API call should be prefixed by MAP_
to allow the option to use the ROM API in a future TI SDK version.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The loop that checks the MPU region permissions incorrectly
iterates from (num_region + 1) to 1. This should be
(num_region - 1) to 0. This results in the wrong regions
being checked and possible overflow for any implementation
that uses the max region value of 0xFF.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Until now, Zephyr has used a patched Kconfiglib that turns 'source' into
a globbing source (by replacing 'source' with 'gsource' at the token
level). There's two problems with this:
- The patch needs to be maintained separately
- Misspelled filenames are silently ignored, as they look like glob
patterns that don't match anything
Fix it as follows:
1. Replace all 'source' statements that use wildcards with 'gsource'
2. Remove the custom Kconfiglib patch so that 'source' no longer globs
The sed pattern '/source.*[*?]/s/source/gsource/' was run over all
Kconfig* files to do the replacement.
source's that use environment variables that might contain glob patterns
were manually changed to gsource.
Building the docs in doc/ is a good test, as doc/Makefile deliberately
sets the environment variables to glob up as many Kconfig files as
possible.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
This commit activates the built-in stack guard on the main_thread
before jumping to it upon system initialization. Stack guard is
activated if BUILTIN_STACK_GUARD is enabled by the user. The
commit also activates built-in thread stack guards at every
context switch, if BUILTIN_STACK_GUARD enabled by the user.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Ignore stack pointer limit checking during a HardFault or NMI
exception, to allow for the Fault handling function to execute
properly.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit implements the build-in interrupt stack protection
via the native MSPLIM register in ARMv8-M MCUs that support the
Main Extension. Main stack pointer overflows will cause Stack
Overflow UsageFaults. In addition, the commit introduces a new
config option, BUILTIN_STACK_GUARD, allowing the user to enable
and use the built-in stack protection in ARMv8-M firmware.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add dma driver for Nios-II Modular Scatter-Gather DMA soft IP.
This driver relies upon the Altera HAL msgdma driver for all
the dma core register programming and interrupt handling.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Add _nios2_dcache_flush_no_writeback() routine to invalidate
cache contents of address provided.
This routine is ported from Altera Nios-II SDK v17.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Modify the linker script with the command INSERT.
It instructs the linker to augment the default linker script
SECTIONS with the ones provided with the one provided in
this script.
It also modified the meaning of the -T switch, so it no longer
replaces the default linker script
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Implements the driver for Intel CAVS I2S. Only Playback
is currently supported.
Change-Id: I7b816f9736dc35e79a81d3664d6405dc0aac15b4
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable the CAVS DMA on intel_s1000. Also, introduce a test to
validate the DMA.
Change-Id: I2ff233c45cfd8aea55e254d905350a666aa649a0
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Introduce the Intel CAVS DMA. This is based out of the DesignWare
DMA IP but the register offset and bits have been changed in some
cases. However, the fundamental definition for the register field
has not been changed. Hence the registers begin with "DW_" to
indicate the Designware origin.
This driver currently supports the single block mode and linked list
multi-block mode. Scatter-Gather is not supported.
Change-Id: I33a8ed5141d9236167de50e14d3d407e95d6f553
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patchset provides Xtensa's xcc compiler support for Xtensa
projects in Cmake. This requires the below environment variables
to be defined aptly. The appropriate xcc license information also
need to be supplied.
ZEPHYR_GCC_VARIANT=xcc
TOOLCHAIN_VER=RF-2015.3-linux
XTENSA_CORE=cavs21_LX6HiFi3_RF3_WB16
XTENSA_SYSTEM=/opt/xtensa/XtDevTools/install/tools/
RF-2015.3-linux/XtensaTools/config/
XTENSA_BUILD_PATHS=/opt/xtensa/XtDevTools/install/builds/
Change-Id: Ib3c10e8095439b0e32276ff37c00eca8420773ec
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000 has multiple levels of interrupts consisting of core, CAVS
Logic and designware interrupt controller. This patchset modifies
the regular gen_isr mechanism to support these multiple levels.
Change-Id: I0450666d4e601dfbc8cadc9c9d8100afb61a214c
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000 makes use of DesignWare IP for I2C.
Change-Id: Ie091318c5959b95e1febeb5cefa440f35a6d144b
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable GPIO handling for intel_s1000. It uses a DesignWare IP.
Change-Id: I522534935e4ef3a56d93aca669f6de961d927481
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
__start is deemed the entry point for all architectures in Zephyr.
Accordingly, Xtensa code had to be modified a bit to fall in line
with this convention.
Change-Id: If3ed344721c9f2735378b866662a68d8d5795324
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000 uses DesignWare IP for UART. National Semiconductor
16550 (UART) component specification is followed in this IP.
Change-Id: Ied7df1dc178d55b6dbe71d729d6383ba07274ea4
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Setting CACHEATTR from _memmap_cacheattr_reset is making
the intel_s1000 SoC get into some unknown state. Removing
it for intel_s1000_crb for now.
Change-Id: Ib44638ef75de6200ef5c2aad55f093a633da864a
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000_crb board makes use of the intel_s1000 SoC. It has
a built-in ROM which gets executed upon applying power. It then
executes the secondary bootloader followed by the FW (like zephyr).
Change-Id: If334c359b4372a56997c3b2e1eb9250e80847f07
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Define memctl_default.S and memerror-vector.S files. A reference
could be found in the Xtensa toolchain directories. These are
required for using cavs21_LX6HiFi3_RF3_WB16 Xtensa CPU mainly in
simulator. On boards which have ROM, these would have been already
defined in the ROM. Hence, the contents of these files will be
developed at a later time if required.
Change-Id: Idf52397bb6880c136525e69f47e09defcba7f036
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000 is an SoC having cavs21_LX6HiFi3_RF3_WB16 as the CPU which
belongs to Xtensa family. This is being used in intel_s1000_crb.
Change-Id: Ic424aa77557bf31024ddbf3f1d76b72a4adb8f66
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
"depends on" cannot use expressions as arguments, this statement
didn't actually do anything for kconfiglib.py and caused an
error with menuconfig.
There's currently no way to depend on a system heap being
present, however forthcoming patches move this feature away
from using the system heap anyway.
For now, if the user enables dynamic objects without defining
a system heap, they will get a build error.
Fixes#7266.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Some of the SoCs specify "Enable MPU" in Kconfig for enabling MPU
support. This will create ambiguity while selecting options via
menuconfig. Hence, append SoC family name to the selection strings
to looks more elaborative.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The title for selecting the configuration options for SoC's should be
"SoC Configuration" not "Board Configuration".
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Improve the help text of ARM k-config option
CPU_CORTEX_M_HAS_PROGRAMMABLE_FAULT_PRIOS.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
It seems like SEGGER is supported across all the NXP SoC families so
lets enable it across all of them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A red-black tree is maintained containing the metadata for all
dynamically created kernel objects, which are allocated out of the
system heap.
Currently, k_object_alloc() and k_object_free() are supervisor-only.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We have been combining imported mcux drivers into a flattened directory
structure to maximize driver reuse, but the introduction of additional
nxp soc families (lpc and imx) to zephyr has introduced driver naming
conflicts. This caused us to rename and modify imported files, such as
fsl_gpio.c/h, to make them unique across all three nxp soc families.
This makes updating the the mcux drivers complicated, especially for the
lpc family.
Reoganize the mcux drivers into soc family subfolders, so we can just
copy all the drivers from an mcux distribution (which is done on an
soc-basis) into the appropriate soc family folder. Undo all of the
naming changes that occurred when lpc and imx drivers were originally
imported. Undo the accidental squashing of the kinetis watchdog and dcdc
drivers that occurred when the imx drivers were introduced.
The drawback to this approach is that we have duplicate files when the
same hw ip modules exist in multiple soc families, however there are
only few cases where this occurs, such as fsl_lpuart and fsl_trng.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In order to mitigate Spectre variant 2 (branch target injection), use
retpolines for indirect jumps and calls.
The newly-added hidden CONFIG_X86_NO_SPECTRE flag, which is disabled
by default, must be set by a x86 SoC if its CPU performs speculative
execution. Most targets supported by Zephyr do not, so this is
set to "y" by default.
A new setting, CONFIG_RETPOLINE, has been added to the "Security
Options" sections, and that will be enabled by default if
CONFIG_X86_NO_SPECTRE is disabled.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Now that other work has eliminated the two cases where we had to do a
reschedule "but yield even if we are cooperative", we can squash both
down to a single _reschedule() function which does almost exactly what
legacy _Swap() did, but wrapped as a proper scheduler API.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
There was a somewhat promiscuous pattern in the kernel where IPC
mechanisms would do something that might effect the current thread
choice, then check _must_switch_threads() (or occasionally
__must_switch_threads -- don't ask, the distinction is being replaced
by real English words), sometimes _is_in_isr() (but not always, even
in contexts where that looks like it would be a mistake), and then
call _Swap() if everything is OK, otherwise releasing the irq_lock().
Sometimes this was done directly, sometimes via the inverted test,
sometimes (poll, heh) by doing the test when the thread state was
modified and then needlessly passing the result up the call stack to
the point of the _Swap().
And some places were just calling _reschedule_threads(), which did all
this already.
Unify all this madness. The old _reschedule_threads() function has
split into two variants: _reschedule_yield() and
_reschedule_noyield(). The latter is the "normal" one that respects
the cooperative priority of the current thread (i.e. it won't switch
out even if there is a higher priority thread ready -- the current
thread has to pend itself first), the former is used in the handful of
places where code was doing a swap unconditionally, just to preserve
precise behavior across the refactor. I'm not at all convinced it
should exist...
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Contrary to ARMv7-M, in ARMv8-M MCUs with the Main Extension,
BusFault Status Register bits are sticky and must be cleared.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
* call the _check_stack_sentinel in unnested isr
return.
* for firq, _check_stack_sentinel is called in kernel
isr stack because the limitation of banked register
* for normal irq, _check_stak_sentinel is called in
the interruptted thread stack
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* For STACK_CANERY, the processor should not hang
* as _SysFatalErrorHandler is always executed in
isr context, so remove k_is_in_isr
* the function should return after k_thread_abort
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The original exception handling has space to optimize and
and some bugs need to be fixed.
* define NANO_ESF
* add the definition of NANO_ESF which is an irq_stack_frame
* add the corresponding codes in exception entry and handler
* remove _default_esf
* implement the _ARCH_EXCEPT
* use trap exception to raise exception by kernel
* add corresponding trap exception entry
* add _do_kernel_oops to handle the exception raised by
_ARCH_EXCEPT.
* add the thread context switch in exception return
* case: kernel oops may raise thread context switch
* case: some tests will re-implement SysFatalHandler to raise
thread context switch.
* as the exception and isr are handled in kernel isr stack, so
the thread context switch must be in the return of exception/isr
, and the exception handler must return, should not be decorated
with FUNC_NORETURN
* for arc, _is_in_isr should consider the case of exception
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
This patch changes the ARM system calls to use registers for passing
or arguments. This removes the possibility of stack issues when
callers do not adhere to the AAPCS.
Fixes#6802
Signed-off-by: Andy Gross <andy.gross@linaro.org>
During the transition of privilege levels while performing syscalls,
the ARM documentation recommends flushing the pipeline to avoid
pre-fetched instructions from being executed with the previous
privilege level.
The manual says:
4.16 CONTROL register
(...) after programming the CONTROL register, an ISB instruction
should be used.
(...) This is not implemented in the Cortex M0 processor.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The TRNG IP block in the KW41Z is really an entropy source and not
intended to be used as a general purpose random number generator
source. The block has 15 slots to read from and when the last slot
is read it has to regenerate the 15 numbers. This process takes
3-5 seconds and is blocking. The change here is to use the TRNG as
an entropy source to the XOROSHIRO pseudo random number function
and then have the KW41Z use XOROSHIRO for random number generation.
Signed-off-by: David Leach <david.leach@nxp.com>
- Removed OT_PLAT_RADIO_DEVICE_NAME
- Changed OpenThread binding to use NET_AP_IEEE802154_DEV_NAME
- Modified Kconfig chain to ensure NET_AP_IEEE802154_DEV_NAME
is enabled for both native 802.15.4 and OpenThread configurations
- Changed default setting of NET_L2_IEEE802154 in defconfig for mkw41z4.
- Fixed OpenThread api support code to use the state of mIsCcaEnabled
in the transmit frame to conditionally invoke radio_api->cc() on
transmits.
Signed-off-by: David Leach <david.leach@nxp.com>
The i.MX7 SoC is a Hybrid multi-core processor composed by Single/Dual
Cortex A7 core and Single Cortex M4 core.
Zephyr was ported to run on the M4 core. In a later release, it will
also communicate with the A7 core (running Linux) via RPmsg.
The low level drivers come from NXP FreeRTOS BSP and are located at
ext/hal/nxp/imx. More details can be found at ext/hal/nxp/imx/README
The A7 core is responsible to load the M4 binary application into the
RAM, put the M4 in reset, set the M4 Program Counter and Stack Pointer,
and get the M4 out of reset.
The A7 can perform these steps at bootloader level after the Linux
system has booted.
The M4 can use up to 5 different RAMs. These are the memory mapping for
A7 and M4:
+---------------+-----------------+---------------------------+
| Memory Name | Start Address | Size |
+===============+=================+===========================+
| TCML | 0x007F8000 | 32KB |
+---------------+-----------------+---------------------------+
| TCMU | 0x20000000 | 32KB |
+---------------+-----------------+---------------------------+
| OCRAM_S | 0x20180000 | 32KB |
+---------------+-----------------+---------------------------+
| OCRAM | 0x00900000 | 128KB |
+---------------+-----------------+---------------------------+
| DDR | 0x10000000 | 256MB |
+---------------+-----------------+---------------------------+
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
All boards based on STM32 should use dts for I2C and SPI.
Move CONFIG flags selection from boards to arch and select them
for all STM32 SoCs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
srd bits start at bit 8, not bit 5.
To date we are not using sub-regions so this problem was
undetected.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Ports F and G are not present on some STM32L0 parts, so
for these parts port H external interrupt should be enabled
by writing value 0x5 instead of 0x7 to SYSCFG_EXTICRn registers
(see e.g. RM0367, 10.2.4).
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Removing ${} variable evaluation fixes the issue.
For sam4s_xplained:
Before:
/repos/zephyr/samples/hello_world/build$ make VERBOSE=1 | grep march
/repos/zephyr/samples/hello_world/build$
After:
/repos/zephyr/samples/hello_world/build$ make VERBOSE=1 | grep march
...
-mthumb -mcpu=cortex-m4 -march=armv7e-m
...
Signed-off-by: Paolo Teti <paolo.teti@gmail.com>
QMSI is not updated to latest SPI API. Switching to native DW driver,
until we find a way either to update the shim drivers in a
non-performant way, or updating QMSI itself enabling support for
scatter-gather type of buffers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This file never existed.
'source' currently ignores missing files instead of throwing an error,
due to Zephyr's custom globbing logic.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Selecting a choice symbol is always a no-op, and the latest version of
Kconfiglib prints a warning. This commit removes all selects of choice
symbols, which might make the Kconfig files a bit clearer and gets rid
of the warnings.
This is just a dumb removal. I did not try to guess the intent of each
select.
Fixes#6849
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Add support for getting some basic params from the DTS for the UART.
The ns16550 driver still needs to be updated to get IRQ and address
info from DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all ARC SoCs we can remove code associated with !HAS_DTS and
select HAS_DTS at the architecture level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add initial device tree support for the em{7,9,11}d SoC and associated
em_starterkit boards. The device tree at this point specifies cpu core,
memory, interrupt controller, uart's and i2c controllers.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that dts i2 qmsi ss nodes generate the right options, let's use
them. Apply the relevant fixup on the targeted SoC.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Applying the change to relevant arch/boards, either in their Kconfig or
the dts specific files.
Taking the opportunity in dw driver to rename the variable the same way
as they are everywhere else in the code (s/dev/dw and s/port/dev) in
init function.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Move driver specific to dedicated file when relevant (i.e.: more than
1-2 options), use if/endif also.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
A previous commit had mistakenly overwritten the copyright years instead
of extending the range. Fix this mistake so that the proper range is
recorded.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The existing nrf5_common.h now applies to other Nordic ICs that are not
part of the "5" family. Instead rename this to nrf_common.h to cover the
upcoming ICs that belong to other families.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use HAS_ Kconfig option as intended, those are invisible option that
signify support of a certain feature that can be selected by a hardware
or platform.
For RTT and system view this was not dont in an inconsistent way.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
STM32F0 flash driver already uses FLASH_PAGE_SIZE from HAL
in flash layout part, so CONFIG_FLASH_PAGE_SIZE is redundant
and confusing.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
The xtensa asm2 layer had a function to select the next switch handle
to return into following an exception. There is no arch-specific code
there, it's just scheduler logic. Move it to the scheduler where it
belongs.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This was previously just a #define in one header file, but we need
this expressed in Kconfig space in case some feature only works
properly with downward-growing stacks.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
If we enable CONFIG_DEBUG_INFO, then we need to fixup the stack
on thread entry so that the EFLAGS value in the EBP slot doesn't
confuse the debugger or any runtime stack unwinding code.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The DCCM_SIZE is defined in terms of K, not bytes, so we need to adjust
it from bytes (generated from dts) to K (used by e CONFIG_DCCM_SIZE).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the dts.fixup back to board dir in prep for support mps2_an521.
The memory maps between the two mps2_an385 and mps2_an521 differ greatly
so its easier to just keep the fixup files with the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Kconfiglib does not support UTF-8 properly yet, so avoid issues by
removing the UTF-8 character from the name until this is fixed.
See https://github.com/ulfalizer/Kconfiglib/pull/41
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit introduces the ARM_SECURE_FIRMWARE k-option,
which indicates that we are building an ARM Secure application.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes the implementation of the SecureFault
handling for ARMv8-M-based Cortex-M33. The implementation is
compiled conditionally with compile-time directive
CONFIG_ARM_SECURE_FIRMWARE, which is to signify the intention to
build a Secure image on ARMv8-M with Security Extensions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add initial support for STM32L073xZ SOC which is not very different
from already supported STM32L072xZ.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
SoC dts fixups are added and the i2c_nrf5 driver is modified to use
the values generated from the device tree.
The I2C_*_DEFAULT_CFG and I2C_*_IRQ_PRI options are removed from board
defconfigs. Bitrate and IRQ priority are configured using using the
device tree instead.
HAS_DTS_I2C is selected on all nrf5 boards to prevent generation of
conflicting defines from Kconfig.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
This commit removes the unnecessary asm inline header for ARM.
It also adapts the stack.h and exc.h to use the ARM CMSIS inline
functions to access the IPSR and MSP registers.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit conditionally selects the ARMV7_M_ARMV8_M_FP option
in ARMv7-M/ARMv8-M Mainline processors, when the Floating Point
Extension is implemented (CPU_HAS_FPU is selected).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes the Stack Overflow UsageFault dumping
for ARMv8-M implementations that support the Main Extension.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit introduces the ARMV8_M_MAINLINE K-config option. The
option signifies the use of an ARMv8-M CPU supporting the Main
Extension. ARMv8-M Main Extension includes additional features
that are not present in the ARMv7-M architecture.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit forces CPU_CORTEX_M_HAS_PROGRAMMABLE_FAULT_PRIOS to
depend on ARMV7_M_ARMV8_M_MAINLINE. This allows the user to get
a build warning if he manually selects
CPU_CORTEX_M_HAS_PROGRAMMABLE_FAULT_PRIOS for a CPU that does
not implement either ARMv7-M or ARMv8-M Mainline.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Move IRQ numbers into device tree so we can remove soc_irq.h. We are
already using IRQ defines generated form the DTS so no point in having
soc_irq.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Further simplify the mps2 SoC code by removing soc_memory_map.h which
now only contains one define for the FPGAIO_BASE_ADDR. We can just move
this to the once place its used.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added device tree support to the ARM SBCon I2C controller. We utilize
the compatiable "arm,versatile-i2c" the binding from Linux for the some
peripheral block.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Clean up Kconfig so each SoC just selects the specific Cortex-M
implementaiton rather than having to select both CORTEX_M and
CORTEX_{M0, M3, M4, etc.}.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the missing fault dumping for MemManage or Bus
fault occuring during floating-point lazy state preservation. In
addition, it introduces a Kconfig option for the ARMv7-M/ARMv8-M
Floating Point Extension.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit removes the macros for ARM fault flags from
include/arch/arm/cortex_m/cmsis.h header, since they are
defined in the respective core_cmXX.h header files. It also
modifies fault.c to use the updated fault macros taken directly
from ARM CMSIS headers.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Switch the SoC device tree to define a single entry per SERCOM instead
of one per mode.
Define a Device Tree binding for the SAM0 SPI and use it instead of
Kconfig for enabling / disabaling instances
Switch the Arduino Zero, Adafruit Feather M0 Basic Proto, and
Trinket M0 to use the new defintion.
Add the APA102 LED that's on the Trinket as a test.
Signed-off-by: Michael Hope <mlhx@google.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch reworks the current ARM __swap() function into a C function.
Due to some issues with using svc calls withing fault handlers, we
needed to change the way we initiate a swap by removing the dependence
on svc #0.
Before __swap() is called, the system has already done an irq_lock().
Upon return from __swap(), the equivalent of an irq_lock() is done due
to restoration of the key value from the irq_lock preceeding the call.
For ARM V6M (M0/M0+), the pendsv bit is toggled and the irqs are
enabled. There is no priority masking in v6m, so it's just a global
enable. For ARM V7M, the priority mask has to be set to 0x0 to allow
for the pendsv IRQ to be taken. This is done for both via a call to
irq_unlock(0).
After this unlock, a pendsv irq will be taken, either at the tail end
of the current irq handling if we are in handler mode, or immediately
due to the pendsv being asserted (no other outstanding irqs). The next
thread will be scheduled.
Upon return from the context switch to the original
thread, the priority mask will already be correct due to the pendsv
processing.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
* the bug comes out when a context switch happens in interrupt
* the bug only affects the em7d in emsk 2.3
* the bug is caused by
* wrong operations of stack
* wrong setting of SEC_STAT's IRM bit
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Keyword FLASH_HAS_PAGE_LAYOUT is related to flash and should
be declared in its Kconfig.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The comment was obsolete; we simply do not allow use of the FPU or
vector math in ISRs. There is no desire to add such support, doing
this is properly offloaded to a worker thread.
Fixes#5283.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This was a little embarassing. The swap code got this right, and the
interrupt exit path got it right, but on entry we weren't ever saving
the shift and loop registers for the interrupted context.
This almost always worked anyway as the loop registers aren't ever
used in any Zephyr code (gcc won't generate this style of loop AFAICT)
and the SAR shift amount register is generally used only in two pairs
of adjacent instructions making the chance of hitting that exact cycle
quite low in general.
But of course we have shift-happy crypto code in our tests, so this
got caught, thankfully.
See https://github.com/zephyrproject-rtos/zephyr/issues/6470
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
MPU_STACK_GUARD option has a direct dependence on ARM_CORE_MPU.
Therefore, it is not required to have a conditional selection
of the option (if ARM_CORE_MPU) in ARM_STACK_PROTECTION.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
ESP-IDF commit cb31222e added the dependency on a file named
"sdkconfig.h", which is equivalent to "autoconf.h" generated by kbuild
used in Zephyr. It does not depend on anything from that file, though,
so just provide an empty file to keep the compiler from complaining.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
When returning into a different thread than we interrupted, we
obviously need to spill all the existing register windows to make sure
all their values are in the old thread's stack. But the code to do
this forgot to reset the current stack pointer to the value it had at
interrupt time (it was still pointing to the saved context below
that), so the caller of the interrupted function was spilling to the
wrong spot.
This wouldn't show up as an instant failure, it would only happen when
switching BACK to the improperly-spilled thread. And even then it
would be a noop if the original interrupt handler was deep enough to
have spilled that function naturally.
In practice, this happened only in some instances on ESP-32 (which has
more windowed registers than qemu) when interrupting the idle thread
(which is very shallow) with a (very simple) timer interrupt. Trivial
to see, hard to find.
See https://github.com/zephyrproject-rtos/zephyr/issues/6346 for more
detail.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
In ARMv7-M (and ARMv8-M) architecture it is
implementation defined whether separate MMFAR and BFAR are
implemented. This commit ensures that we always get the true
faulting address displayed in case of MemManage- or BusFault.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Move common SoC dts.fixup defines into arch/arm/soc/<SOC>/dts.fixup so
we remove duplication in the boards and only have board specific
defines in boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/x86/soc/atom/dts.fixup so we
remove duplication in the boards and only have board specific defines in
boards/x86/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/x86/soc/ia32/dts.fixup so we
remove duplication in the boards and only have board specific defines in
boards/x86/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/x86/soc/intel_quark/quark_se/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/x86/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arc/soc/quark_se_c1000_ss/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arc/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added a basic command line parameter parsing framework
Added the following options by now:
--stop-at=<time>: Auto-stop after <time> seconds
--seed=<seed> : random seed for entropy device
--testargs : any argument that follows is ignored in top level
and made available thru
native_get_test_cmd_line_args()
All command line parameters are still avaliable by calling
native_get_cmd_line_args(), but now you can also call
native_get_test_cmd_line_args() to get whatever was set after
--testargs
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Some of APIs of POSIX implmentation layer has same name as
native_posix architecture. posix_cheats.h is used to handle this
duplication in API name. Adding a guard in posix_cheats.h based on
CONFIG_PTHREAD_API.
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
This patch provides POSIX sleep APIs for POSIX 1003.1 PSE52 standard.
sleep(n) is implemented using Zephyr k_sleep API.
uleep(n) is implemented using Zephyr k_sleep/k_busy_Wait API.
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Move common SoC dts.fixup defines into
arch/arm/soc/atmel_sam/<BAR>/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/arm/soc/nxp_imx/rt/dts.fixup
so we remove duplication in the boards and only have board specific
defines in boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/kwx/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/kl2x/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_lpc/lpc54xxx/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/k6x/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/ti_simplelink/<BAR>/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Include `soc.h` first, which will include the ESP-IDF headers -- which
will define the `BIT()` macro without checking if they're already
defined, like the Zephyr headers do.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Add SPI fixup defines on STM32 SoC family level for all SPIs that
are supported on one or more SOCs of that SoC family.
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
The xtensa headers use this for simplicity when SMP is not enabled.
It should still build on older platforms that don't include the
asm2-style CPU pointer scheme.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Non-asm2 devices without a generated SoC interrupt file will see a
compile failure due to the missing header.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
It's not impossible that something we just handled (e.g. a machine
exception) called k_thread_abort() on our current thread. Don't try
to return into it, check the DEAD state.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
In asm2, the machine exception handler runs in interrupt context (this
is good: it allows us to defer the test against exception type until
after we have done the stack switch and dispatched any true
interrupts), but that means that the user error handler needs to be
invoked and then return through the interrupt exit code.
So the __attribute__(__noreturn__) that it was being decorated with
was incorrect. And actually fatal, as with gcc xtensa will crash
trying to return from a noreturn call.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
When in SMP mode, the nested/irq_stack/current fields are specific to
the current CPU and not to the kernel as a whole, so we need an array
of these. Place them in a _cpu_t struct and implement a
_arch_curr_cpu() function to retrieve the pointer.
When not in SMP mode, the first CPU's fields are defined as a unioned
with the first _cpu_t record. This permits compatibility with legacy
assembly on other platforms. Long term, all users, including
uniprocessor architectures, should be updated to use the new scheme.
Fundamentally this is just renaming: the structure layout and runtime
code do not change on any existing platforms and won't until someone
defines a second CPU.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The xtensa-asm2 work included a patch that added nano_internal.h
includes in lots of places that needed to have _Swap defined, because
it had to break a cycle and this no longer got pulled in from the arch
headers.
Unfortunately those new includes created new and more amusing cycles
elsewhere which led to breakage on other platforms.
Break out the _Swap definition (only) into a separate header and use
that instead. Cleaner. Seems not to have any more hidden gotchas.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Simply define the Kconfig variables in this patch so they can be used
in later patches. Define MP_NUM_CPUS correctly on esp32. No code
changes.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This is a mostly-internal API to start a secondary system CPU, with an
implementation for the ESP-32 "APP" cpu. Exposed in kernel.h because
it's plausibly useful for asymmetric MP code managed by an app.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Xtensa register windows have a special exception that happens when the
stack pointer needs to be moved, but the caller function has already
spilled its registers below it.
I thought these were unexercised in Zephyr code, but they turn out to
be thrown by the existing mem_pool tests when run in the 32-register
qemu environment (but not on 64-register hardwre). Because the effect
of the exception is to unspill the caller, there is no good way to
handle this in a traditional handler. Instead put a 5-instruction
stub in front of the user exception handler (i.e. incurring that cost
on every trap and every L1 interrupt) to test before doing the normal
entry.
Works, but would be nicer to optimize this in the future so that only
true alloca exceptions take that cost.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This macro was already available add an external symbol so C code can
access it (via CALL0 -- it's not and can't be an actual function).
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The API allows any byte count for stack size, and tests in fact check
that a stack with a 499 byte stack works correctly. No choice, have
to do this at runtime.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
You'd this feature would be portable, but it's arch-specific.
Initialize the CONFIG_THREAD_MONITOR stuff, placing the __thread_entry
struct (which AFAICT is dead: nothing in the tree actually reads it)
at the top of the stack.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The stack initilaization was calling the user-provided entry function
directly, which works fine until that function returns, at which point
it will try to unspill A0-A3 from the 16 bytes above the allocated
stack and then "return" to a NULL pointer.
The kernel provides a _thread_entry() function that does cleanup
properly, so use that.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
When using _arch_switch() context switching, the thread return value
is a generic hook and not provided by the architecture.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This adds vectors for all interrupt levels defined by core-isa.h.
Modify the entry code a little bit to select correct linker sections
(levels 1, 6 and 7 get special names for... no particularly good
reason) and to constructed the interrupted PS value correctly (no EPS1
register for exceptions since they had to have interrupted level 0
code and thus differ only in the EXCM bit).
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This python script reads the core-isa.h interrupt definitions (via
running a template file through the toolchain preprocessor to generate
an input file) and emits a fully populated, optimized C handling code
that binary searches only the declared interrupts at a given level and
correctly detects spurious interrupts (and/or incorrect core-isa.h
definitions).
The generated code, alas, turns out not to be any faster than simply
searching the interrupt mask with CLZ (er, NSAU in xtensese), though
it could be faster in theory if the compiler made different choices,
see comments. But I like this for the robustness of the fully
populated search trees and the checking of level vs. mask.
This simply commits the script output into the source tree, including
some checking code to force a build error if the toolchain changes the
headers incompatibly. It would be better long term to have these
headers be generated at build time, but that requires more cmake fu
than I have.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The asm2 layer will build alongside the traditional assembly, but the
reverse is not true. Add a CONFIG_XTENSA_ASM2 to force its use at
runtime and disable the older code.
Note that the older assembly had an initialization function that is
properly part of the timer driver. Move a C equivalent into the timer
driver itself for now to prevent a build breakage. Long term we need
to clean that driver up in a bunch of other ways.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Legacy xtensa had a rather complicated implementation of en/disabling
interrupts, owing to the "software priority" feature (which plays
games with INTENABLE and INTLEVEL to allow for interrupts to interrupt
each other outside their normal priorities). But that's not a Zephyr
feature, it's enabled by a XT_USE_SWPRI value that comes from platform
headers and isn't enabled on any of our boards. Dead code, basically.
Replace with the obvious implementation when asm2 is in use.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This was a dead API. Nothing ever used it, it wasn't exposed in any
API headers. It never appeared in documentation. It's not
particularly clear why a Zephy app would want to hook
architecture-specific exceptions instead of simply using the portable
error framework anyway. And it's not supported by asm2. Delete.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The existing __swap() mechanism is too high level for some
applications because of its scheduler-awareness. This introduces a
new _arch_switch() mechanism, which is a simpler primitive that looks
like:
void _arch_switch(void *handle, void **old_handle_out);
The new thread handle (typically just a stack pointer) is specified
explicitly instead of being picked up from the scheduler by
per-architecture code, and on return the "old" thread handle that got
switched out is returned through the pointer.
The new primitive (currently available only on xtensa) is selected
when CONFIG_USE_SWITCH is "y". A new C _Swap() implementation based
on this primitive is then added which operates compatibly.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
_Swap() is defined in nano_internal.h. Everything calls _Swap().
Pretty much nothing that called _Swap() included nano_internal.h,
expecting it to be picked up automatically through other headers (as
it happened, from the kernel arch-specific include file). A new
_Swap() is going to need some other symbols in the inline definition,
so I needed to break that cycle. Now nothing sees _Swap() defined
anymore. Put nano_internal.h everywhere it's needed.
Our kernel includes remain a big awful yucky mess. This makes things
more correct but no less ugly. Needs cleanup.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
SMP needs a new context switch primitive (to disentangle _swap() from
the scheduler) and new interrupt entry behavior (to be able to take a
global spinlock on behalf of legacy drivers). The existing code is
very obtuse, and working with it led me down a long path of "this
would be so much better if..." So this is a new context and entry
framework, intended to replace the code that exists now, at least on
SMP platforms.
New features:
* The new context switch primitive is xtensa_switch(), which takes a
"new" context handle as an argument instead of getting it from the
scheduler, returns an "old" context handle through a pointer
(e.g. to save it to the old thread context), and restores the lock
state(PS register) exactly as it is at entry instead of taking it as
an argument.
* The register spill code understands wrap-around register windows and
can avoid spilling A4-A15 registers when they are unused by the
interrupted function, saving as much as 48 bytes of stack space on
the interrupted stacks.
* The "spill register windows" routine is entirely different, using a
different mechanism, and is MUCH FASTER (to the tune of almost 200
cycles). See notes in comments.
* Even better, interrupt entry can be done via a clever "cross stack
call" I worked up, meaning that the interrupted thread's registers
do not need to be spilled at all until they are naturally pushed out
by the interrupt handler or until we return from the interrupt into
a different thread. This is a big efficiency win for tiny
interrupts (e.g. timers), and a big latency win for all interrupts.
* Interrupt entry is 100% symmetric with respect to medium/high
interrupts, avoiding the problems seen with hooking high priority
interrupts with the current code (e.g. ESP-32's watchdog driver).
* Much smaller code size. No cut and paste assembly. No use of HAL
calls.
* Assumes "XEA2" interrupt architecture, the register window extension
(i.e. no CALL0 ABI), and the "high priority interrupts" extension.
Does not support the legacy processor variants for which we have no
targets. The old code has some stuff in there to support this, but
it seems bitrotten, untestable, and I'm all but certain it doesn't
work.
Note that this simply adds the primitives to the existing tree in a
form where they can be unit tested. It does not replace the existing
interrupt/exception handling or _Swap() implementation.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Xtensa has a "high priority" class of interrupt levels which ignore
the EXCM bit and can thus interrupt running exception handlers. These
can't be used for C handlers in the general case[1] because C code
needs to be able to throw window over/underflow exceptions, which are
not reentrant.
But the high priority interrupts might be useful to a carefully
designed application, or to unit tests of low level architecture code.
So make their generation optional with this kconfig option.
[1] ESP-32 has a high priority interrupt for its watchdog, apparently.
Which is sort of OK given that it never needs to return to the
interrupted code.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The new thread stack layout is as follow:
|---------------------|
| user stack |
|---------------------|
| stack guard (opt.) |
|---------------------|
| privilege stack |
-----------------------
For MPUv2
* user stack is aligned to the power of 2 of user stack size
* the stack guard is 2048 bytes
* the default size of privileg stack is 256 bytes.
For user thread, the following MPU regions are needded
* one region for user stack, no need of stack guard for user stack
* one region for stack guard when stack guard is enbaled
* regions for memory domain.
For kernel thread, the stack guard region will be at the top, adn
The user stack and privilege stack will be merged.
MPUv3 is the same as V2's layout, except no need of power of 2
alignment.
* reimplement the user mode enter function. Now it's possible for
kernel thread to drop privileg to user thread.
* add a separate entry for user thread
* bug fixes in the cleanup of regs when go to user mode
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
when USERSPACE is enabled, exception is handled in the privilege
stack of thread. This make thread context switch is possible in the
exception handler. For some case,e.g. tests, this is useful.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
disable the U bit of irq.ctrl, so the user thread's context will
be saved into privilege stack when interrupts/exception come.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
scrub all the regs of kernel context before returnning to userspace.
For sys call, ro is not cleared as it's a return value of sys call.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Enable us bit to check user mode more efficienly.
US is read as zero in user mode. This will allow use mode sleep
instructions, and it enables a form of denial-of-service attack
by putting the processor in sleep mode, but since interrupt
level/mask can't be set from user space that's not worse than
executing a loop without yielding.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* user space support requires THREAD_INFO
* for MPU version 2, the stack align is at least 2048 bytes
* the smallest mpu region is 2048 bytes
* the region size must bt power of 2
* the start address of region must be aligned to the region size
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* add the implementation of syscall
* based on 'trap_s' intruction, id = 3
* add the privilege stack
* the privilege stack is allocted with thread stack
* for the kernel thread, the privilege stack is also a
part of thread stack, the start of stack can be configured
as stack guard
* for the user thread, no stack guard, when the user stack is
overflow, it will fall into kernel memory area which requires
kernel privilege, privilege violation will be raised
* modify the linker template and add MPU_ADDR_ALIGN
* add user space corresponding codes in mpu
* the user sp aux reg will be part of thread context
* When user thread is interruptted for the 1st time, the context is
saved in user stack (U bit of IRQ_CTLR is set to 1). When nest
interrupt comes, the context is saved in thread's privilege stack
* the arc_mpu_regions.c is moved to board folder, as it's board
specific
* the above codes have been tested through tests/kernel/mem_protect/
userspace for MPU version 2
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The old ARMV6_M Kconfig option has been removed, and so to correctly set
the dependencies for SW_VECTOR_RELAY we need to use the new
ARMV6_M_ARMV8_M_BASELINE.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This patch fixes a hole in the stack guard configuration. The initial
branch to main is missing the stack guard configuration.
Fixes: Issue #3718
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch fixes calculations for the top of the interrupt and main
stacks. Due to power of two alignment requirements for certain MPUs,
the guard size must be taken into account due to the guard being
counted against the initial stack size.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support for userspace on ARM architectures. Arch
specific calls for transitioning threads to user mode, system calls,
and associated handlers.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds a configure_mpu_user_context API and implements
the required function placeholders in the NXP and ARM MPU files.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
During compile of lwm2m_client using qemu_x86, the following build
warning was noticed:
zephyr/arch/x86/core/excstub.S:132:2: warning: "/*" within comment [-Wcomment]
/*
In commit ff42bdd0a0 ("debug: remove option GDB_INFO"), the comment tag
was omitted. Fix the comment end tag.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
This feature is X86 only and is not used or being tested. It is legacy
feature and no one can prove it actually works. Remove it until we have
proper documentation and samples and multi architecture support.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This feature is X86 only and is not used or being tested. It is legacy
feature and no one can prove it actually works. Remove it until we have
proper documentation and samples and multi architecture support.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Atmel SAMD21 series was classified too broadly as SAMD.
This patch names it correctly to make room,
for other members of SAMD series
Signed-off-by: Sean Nyekjaer <sean@nyekjaer.dk>
Also pull out the SERCOM pads configuration to defines. Note that the
SAM0 has a two level configuration - a signal (like TX) is mapped to a
pad, and then a pad is mapped to a function on a pin.
Signed-off-by: Michael Hope <mlhx@google.com>
This commit defines the Kconfig options for
ARM Cortex-M23 and Cortex-M33 CPUs. It also
udpates the generic memory map for M23 and M33
implementations.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This PR includes the required changes in order to support
conditional compilation for Armv8-M architecture. Two
variants of the Armv8-M architecture are defined:
- the Armv8-M Baseline (backwards compatible with ARMv6-M),
- the Armv8-M Mainline (backwards compatible with ARMv7-M).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add I2C Master driver for Nios-II I2C soft IP core.
This driver relies upon the Altera HAL I2C driver for all the bus level
transactions, interrupt handling and register programming.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Just some exclusions to coverage in code which cannot be
reached, or can only be reached in error conditions
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Added possibility to reconfigure CONFIG_SYS_CLOCK_TICKS_PER_SEC
for the native_posix board (before it could only be 100)
+
Fixed tickless idle support
+
Minor fixes in irq wrapping
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Whenever a Cortex-M0+ supports the VTOR register it makes no sense to
use the software vector relay mechanism. Therefore change the logic so
that SW_VECTOR_RELAY does not get enabled whenever a VTOR register is
present, but enable it if an M0+ has no VTOR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In a scenario where a platform harbours multiple interrupts to the
extent the core cannot support it, an interrupt controller is added
as an additional level of interrupt. It typically combines several
sources of interrupt into one line that is then routed to the parent
controller.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
This patch adds the generation and incorporation of privileged stack
regions that are used by ARM user mode threads. This patch adds the
infrastructure for privileged stacks. Later patches will utilize the
generated stacks and helper functions.
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds application data section alignment constraints
to match the region definition requirements for ARM MPUs. Most MPUs
require a minimum of 32 bytes of alignment for any regions, but some
require power of two alignment to the size of a region.
This requires that the linker align the application data section to
the size of the section. This requires a linker pass to determine the
size. Once this is accomplished the correct value is added to a linker
include file that is utilized in subsequent linker operations.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Replace seldom occurrences of FLASH_DRIVER_NAME by equivalent
and commonly used FLASH_DEV_NAME.
Fixes#5919.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Some ARMv6-M Cortex-M0+-based SOCs have VTOR register
and can relocate vector table just as ARMv7-M ones.
Vector table relocation path should be choosed
by VTOR presence, not by arch.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Add Altera Nios-II QSPI Flash controller driver which has
has 1024 blocks or sectors wich each sector size being 64K bytes.
This driver supports flash erase, write, read and lock operations.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Some code in the POSIX architecture is only meant to handle
safely errors which should never occur and therefore
are not covered.
=> We exclude them from the coverage reports.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Some code in the POSIX SOC (inf_clock) will only be executed
if the program is terminated by receiving a SIGTERM in a particular
part. Therefore to avoid confusing developers with changing
coverage, let's exclude it from the coverage reports.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Some code in the POSIX arch core will only be executed
in some very atypical cases depending on the host load.
To avoid confusing developers, let's exclude it from the
coverage reports.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Added a new config variable with the recommended stack
size for threads which are only meant for the posix architecture
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Defines the FLASH_DRIVER_NAME macro in soc.h for kinetis kl2x and kwx
SoC series. This macro is used by the storage and dfu subsystems, as
well as the flash_shell sample.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Rename the nano_internal.h to kernel_internal.h and modify the
header file name accordingly wherever it is used.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
rename main_clean_up() to posix_exit() for consistency
with all other global functions of this architecture
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Currently in zephyr the support for the arm userspace has not be
merged. But the Kconfig always sets the userspace flag and causes a
build failure. This is blocking the test cases for userspace.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Add a new Kconfig option, BOOTLOADER_MCUBOOT, that automatically sets
the required options necessary to make the resulting image bootable by
the MCUboot open source bootloader. This includes the text section
offset and the vector relay table for Cortex-M0, and in the future it
might also add the DTS overlay required to link at slot0 offset in
flash.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add device tree support for the "nxp,kinetis-ftfa" flash controller used
on the NXP KL2X and KW4xZ SoCs.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert NXP k6x and kw2xd flash driver to use device tree to get the
flash controller name from device tree. We introduce yaml bindings for
the "nxp,kinetis-ftfe" and "nxp,kinetis-ftfl" devices.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The old HAL and MDK have been removed from the source tree.
Since RADIO HAL is not yet present in nrfx, the "nrf_radio.h" file
was temporarily moved to "nrfx/hal" folder. It will be replaced with
the proper file from nrfx in its next update.
Signed-off-by: Michał Kruszewski <michal.kruszewski@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit adds a glue layer that adapts nrfx to be usable in Zephyr
as a host environment and files with static configuration of nrfx
drivers for several supported SoCs.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This moves and merges the existing board-level dts.fixup files
for STM32 L4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
disco_l475_iot1 boards fixup blocks for devices connected via SPI
and I2C stay in board level dts.fixup file, because they are board
specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F3 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F1 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
96b_carbon boards fixup block for Bluetooth HCI device via SPI
stays in board level dts.fixup file, because it is board specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F0 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Convert Atmel SAM0 flash driver to use device tree to get the flash
controller name and base address.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For SoCs that don't support vector table relocation in hardware, may not
support bootloader like mcuboot.
We introduce a way to relocate vector table in software by forwarding
the control of incoming IRQs to a new vector table which address is save
at fixed SRAM address.
User can change the data in that fixed SRAM address in order to relocate
vector table in software way.
Signed-off-by: Ding Tao <miyatsu@qq.com>
Cortex-M0 do not have the Vector Table Base Address Offset Register, so
Cortex-M0 vector table address can not be changed.
But in some Cortex-M0 SoCs like STM32F0 series, they have some mechanism
that can remap the vector table address to the start address of SRAM.
Use this flag to indicates whether current Cortex-M0 SoC support such a
remap or not.
Signed-off-by: Ding Tao <miyatsu@qq.com>
In order to be able to build MCUboot for nRF51 we require the flash
driver name in the nRF51 soc.h header.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Refering the ARM's implementation, the initial support of memory
domain in ARC is added:
* changes in MPU drivers
* changes in Kconfig
* codes to configure memory domain during thread swap
* changes in linker script template
* memory domain related macro definitions
the commited codes are simply tested through
samples/mpu/mem_domain_apis_test.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
It appears the STM32F411XE doesn't support RNG so remove enabling it
from the SoC defconfig and flag an error if attempting to build the
driver on that SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A fix for this issue is in progress, meanwhile warn the user that
they may be susceptible to this problem if they enable user mode on
an x86-based target that is not known to be immune.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
When Kconfiglib was introduced it caused a significant performance
issue. This patch uses pruning to mitigate the performance issue.
The pruning exploits the fact that before the Kconfig database is
parsed we already know what ARCH and BOARD has been selected. So in
theory we could prune away all Kconfig sources that are not related to
the current ARCH or BOARD. In practice, it is only the Kconfig sources
in zephyr/arch/$ARCH and zephyr/board/$ARCH/ that are easy to prune.
Still, that is quite a few Kconfig sources. For qemu_x86 this patch
reduced the number of parsed Kconfig source files from 632 to
272. This pruning resulted in a incremental reconfiguration (time
cmake ..) speedup of 21% (0.56s to 0.46) and a clean build speedup of
4% (Using board qemu_x86 and sample hello_world).
Furthermore, it should be easier to maintain ARCH's and BOARD's
out-of-tree since the user now has a mechanism to redirect where
Kconfig sources are found. But this has not been explored.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
In STM32 family, RNG IP is available only on F4 and L4 series.
Besides STM32F401 does not support is neither.
Get entropy driver available on STM32 devices supporting it and
generate a compilation issue on STM32 devices that do not own
the RNG IP.
Solves #5448
Signed-Off-By: Erwan Gouriou <erwan.gouriou@linaro.org>
When asserts are enabled we run into an issue with newlib and types of
printf style formatters not matching. The easy fix to this is to cast
the uint32_t to u32_t to make things consistent with or without newlib
enabled.
This fixes#5645
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Instead of accessing the environment variable ZEPHYR_BASE every time we
require accessing the source code root, use an intermediate variable
that has OS path separators correctly set to '/' to avoid issues on
Windows.
Note: This removes the ZEPHYR_SOURCE_DIR CMake variable. External
applications using that will need to change to use the new ZEPHYR_BASE
variable.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Current STM32 SoC initialization code sets really weird startup values
to SystemCoreClock. It should be consistent with Reference Manuals after
this change.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Include low level random generator header in case stm32 random number
generator should be used by entropy driver
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
With the native port we are able to generate coverage reports, add the
needed options to the compliler and add a kconfig option to enable this
on the supported architectures.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A new arch (posix) which relies on pthreads to emulate the context
switching
A new soc for it (inf_clock) which emulates a CPU running at an
infinely high clock (so when the CPU is awaken it runs till completion
in 0 time)
A new board, which provides a trivial system tick timer and
irq generation.
Origin: Original
Fixes#1891
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Was ARM specific and could not be used by other architectures.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The PIO cores on Altera Nios-II processors can be used
for GPIOs and each PIO core can be configured as Input only,
Output only or as Bidirectional port from the Qsys tool.
The present Nios-II softcpu image on the Zephyr only has the
support for Output only port and the PIOs[0:3] are wired to
LED[0:3] on the Altera MAX10 board.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
when a current thread is added to a memory domain the pages/sections
must be configured immediately.
A problem occurs when we add a thread to current and then drop
down to usermode. In such a case memory domain will become active
the next time a swap occurs.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Add an architecure specfic code for the memory domain
configuration. This is needed to support a memory domain API
k_mem_domain_add_thread.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
The system ID core is a simple read-only device that
provides Qsys systems with a unique identifer.
Nios-II processor systems use the system ID core to
verify that an executable program was compiled targeting
the actual hardware image configured in the target FPGA.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
MPU version 3 is included in em7d of em_starterkit 2.3.
The differences of MPU version 3 and version 2 are:
* different aux reg interface
* The address alignment requirement is 32 bytes
* supports secure mode
* supports SID (option)
* does not support memory region overlap
This commit adds the support MPU version 3 and also make some changes to
MPU version 2 to have an unified interface.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* em7d of em_starterkit 2.3 supports secure mode. add the support
in kconfig and build system.
* change the default configuration of em_starterkit 2.3 to em7d
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
In ARC's SecureShield, a new secure mode (currently only em) is added.
The secure/normal mode is orthogonal to kernel/user mode. The
differences between secure mode and normal mode are following:
* different irq stack frame. so need to change the definition of
_irq_stack_frame, assembly code.
* new aux regs, e.g, secure status(SEC_STAT), secure vector base
(VECT_BASE_S)
* interrupts and exceptions, secure mode has its own vector base;
interrupt can be configured as secure or normal through the
interrupt priority aux reg.
* secure timers. Two secure timers (secure timer 0 and timer 1) are
added.Here, for simplicity and backwards compatibility original
internal timers (timer 0 and timer1) are used as sys clock of zephyr
* on reset, the processor is in secure mode and secure vector base is
used.
Note: the mix of secure and normal mode is not supported, i.e. it's
assumed that the processor is always in secure mode.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Add FIRQ option and change the _isr_wrapper. Currently, firq is
enabled by default, but in some arc configuration, firq can be
disabled.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Some drivers doesn't implement flash API page layout extension
which is causing the application crash once the API was calling.
This patch introduce system termination for this in those drivers
which doesn't implement extension. This will help to discover this
problem early.
It is not done by preprocessor check because it is possible to have
enabled a driver which support and a driver which doesn't support
this API simultaneously.
Now FLASH_PAGE_LAYOUT configuration option is accessible only in case
that at last one driver which implements mentioned API is enabled.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Enable USB OTG support for olimex stm32-e407 and stm32f407g_disc1
boards by adding USB OTG to the pinmux table. Also, fix out of
range endpoint addresses in CDC ACM case for STM32F4 based boards.
Signed-off-by: Sudarsana Nagineni <sudarsana.nagineni@intel.com>
'make flash' is failing for altera_max10 board due to the
missing NIOS2_CPU_SOF environment variable. Though it is set
in arch/nios2/soc/nios2f-zephyr/CMakeLists.txt but it is not
taking effect when flashing script is run. The reason could be
following which is mentioned in https://itk.org/Wiki/CMake_FAQ
"environment variables SET in the CMakeLists.txt only
take effect for cmake itself (configure-time), so you cannot use
this method to set an environment variable that a custom command
might need (build-time)."
Now, NIOS2_CPU_SOF is set from boards/nios2/altera_max10/board.cmake
file which is more logical because all the FLASH related environment
variables are being set from board.cmake
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
The exticrX registers were shifted by a word, so configuring
an EXTI line on a port different of PA misconfigured the EXTI line
source and could flood with unwanted events.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Added Inter-IC Sound driver (based on SSC module) for Atmel
SAM MCU family.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-2509
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added DMA (XDMAC) driver for Atmel SAM MCU family. The driver provides
private DMA API to be used by the SAM family device drivers. Public
DMA API to be used by user space programs is currently missing.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1609
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Save the required scratch pad register (in this case only edx)
before calling the C function.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Not all boards require the various binary formats zephyr generates. So
be selective based on the arch, SoC or board and only geenrate the
binaries actually needed.
Fixes#5009
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Implement API to validate user buffer. This API will iterate
all MPU regions to check if the given buffer is user accessible
or not. For #3832.
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
Unlike other NXP SoCs currently in Zephyr, the mimxrt1052 has the ARM
MPU rather than the NXP MPU. Start out by enabling it with a simple set
of memory regions for "flash" (ITCM), "ram" (DTCM), and the peripheral
buses. More regions will need to be added when we implement support for
external memories.
Tested with:
- samples/mpu/mpu_stack_guard_test
- tests/kernel/mem_protect/protection
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds the mimxrt1052 SoC, which belongs to a new family (nxp_imx) and
series (rt) of SoCs. The mimxrt1052 integrates an Arm Cortex-M7 core,
512 KB TCM, and many peripherals including 2D graphics, an LCD display
controller, camera interface, SPDIF and I2S. Unlike other SoCs in
Zephyr, the mimxrt1052 has no internal flash.
This initial port to mimxrt1052 configures the system clock to operate
at 528 MHz, and enables the serial/uart and gpio interfaces to support
the hello_world and blinky samples. Support for additional Zephyr driver
interfaces will come later.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
When CONFIG_X86_MMU is enabled for arduino 101 the start address
should be aligned to 4kB. If not aligned the page tables would not
be created and the build fails.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
During swap the required page tables are configured. The outgoing
thread's memory domain pages are reset and the incoming thread's
memory domain is loaded. The pages are configured if userspace
is enabled and if memory domain has been initialized before
calling swap.
GH-3852
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Added architecture specific support for memory domain destroy
and remove partition for arm and nxp. An optimized version of
remove partition was also added.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
This is intended for memory-constrained systems and will save
4K per thread, since we will no longer reserve room for or
activate a kernel stack guard page.
If CONFIG_USERSPACE is enabled, stack overflows will still be
caught in some situations:
1) User mode threads overflowing stack, since it crashes into the
kernel stack page
2) Supervisor mode threads overflowing stack, since the kernel
stack page is marked non-present for non-user threads
Stack overflows will not be caught:
1) When handling a system call
2) When the interrupt stack overflows
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Besides the fact that we did not have that for the current supported
boards, that makes sense for this new, virtualized mode, that is meant
to be run on top of full-fledged x86 64 CPUs.
By having xAPIC mode access only, Jailhouse has to intercept those MMIO
reads and writes, in order to examine what they do and arbitrate if it's
safe or not (e.g. not all values are accepted to ICR register). This
means that we can't run away from having a VM-exit event for each and
every access to APIC memory region and this impacts the latency the
guest OS observes over bare metal a lot.
When in x2APIC mode, Jailhouse does not require VM-exits for MSR
accesses other that writes to the ICR register, so the latency the guest
observes is reduced to almost zero.
Here are some outputs of the the command line
$ sudo ./tools/jailhouse cell stats tiny-demo
on a Jailhouse's root cell console, for one of the Zephyr demos using
LOAPIC timers, left for a couple of seconds:
Statistics for tiny-demo cell (x2APIC root, x2APIC inmate)
COUNTER SUM PER SEC
vmexits_total 7 0
vmexits_management 3 0
vmexits_cr 2 0
vmexits_cpuid 1 0
vmexits_msr 1 0
vmexits_exception 0 0
vmexits_hypercall 0 0
vmexits_mmio 0 0
vmexits_pio 0 0
vmexits_xapic 0 0
vmexits_xsetbv 0 0
Statistics for tiny-demo cell (xAPIC root, xAPIC inmate)
COUNTER SUM PER SEC
vmexits_total 4087 40
vmexits_xapic 4080 40
vmexits_management 3 0
vmexits_cr 2 0
vmexits_cpuid 1 0
vmexits_msr 1 0
vmexits_exception 0 0
vmexits_hypercall 0 0
vmexits_mmio 0 0
vmexits_pio 0 0
vmexits_xsetbv 0 0
Statistics for tiny-demo cell (xAPIC root, x2APIC inmate)
COUNTER SUM PER SEC
vmexits_total 4087 40
vmexits_msr 4080 40
vmexits_management 3 0
vmexits_cr 2 0
vmexits_cpuid 1 0
vmexits_exception 0 0
vmexits_hypercall 0 0
vmexits_mmio 0 0
vmexits_pio 0 0
vmexits_xapic 0 0
vmexits_xsetbv 0 0
See that under x2APIC mode on both Jailhouse/root-cell and guest, the
interruptions from the hypervisor are minimal. That is not the case when
Jailhouse is on xAPIC mode, though. Note also that, as a plus, x2APIC
accesses on the guest will map to xAPIC MMIO on the hypervisor just
fine.
Signed-off-by: Gustavo Lima Chaves <gustavo.lima.chaves@intel.com>
This is an introductory port for Zephyr to be run as a Jailhouse
hypervisor[1]'s "inmate cell", on x86 64-bit CPUs (running on 32-bit
mode). This was tested with their "tiny-demo" inmate demo cell
configuration, which takes one of the CPUs of the QEMU-VM root cell
config, along with some RAM and serial controller access (it will even
do nice things like reserving some L3 cache for it via Intel CAT) and
Zephyr samples:
- hello_world
- philosophers
- synchronization
The final binary receives an additional boot sequence preamble that
conforms to Jailhouse's expectations (starts at 0x0 in real mode). It
will put the processor in 32-bit protected mode and then proceed to
Zephyr's __start function.
Testing it is just a matter of:
$ mmake -C samples/<sample_dir> BOARD=x86_jailhouse JAILHOUSE_QEMU_IMG_FILE=<path_to_image.qcow2> run
$ sudo insmod <path to jailhouse.ko>
$ sudo jailhouse enable <path to configs/qemu-x86.cell>
$ sudo jailhouse cell create <path to configs/tiny-demo.cell>
$ sudo mount -t 9p -o trans/virtio host /mnt
$ sudo jailhouse cell load tiny-demo /mnt/zephyr.bin
$ sudo jailhouse cell start tiny-demo
$ sudo jailhouse cell destroy tiny-demo
$ sudo jailhouse disable
$ sudo rmmod jailhouse
For the hello_world demo case, one should then get QEMU's serial port
output similar to:
"""
Created cell "tiny-demo"
Page pool usage after cell creation: mem 275/1480, remap 65607/131072
Cell "tiny-demo" can be loaded
CPU 3 received SIPI, vector 100
Started cell "tiny-demo"
***** BOOTING ZEPHYR OS v1.9.0 - BUILD: Sep 12 2017 20:03:22 *****
Hello World! x86
"""
Note that the Jailhouse's root cell *has to be started in xAPIC
mode* (kernel command line argument 'nox2apic') in order for this to
work. x2APIC support and its reasoning will come on a separate commit.
As a reminder, the make run target introduced for x86_jailhouse board
involves a root cell image with Jailhouse in it, to be launched and then
partitioned (with >= 2 64-bit CPUs in it).
Inmate cell configs with no JAILHOUSE_CELL_PASSIVE_COMMREG flag
set (e.g. apic-demo one) would need extra code in Zephyr to deal with
cell shutdown command responses from the hypervisor.
You may want to fine tune CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC for your
specific CPU—there is no detection from Zephyr with regard to that.
Other config differences from pristine QEMU defaults worth of mention
are:
- there is no HPET when running as Jailhouse guest. We use the LOAPIC
timer, instead
- there is no PIC_DISABLE, because there is no 8259A PIC when running
as a Jailhouse guest
- XIP makes no sense also when running as Jailhouse guest, and both
PHYS_RAM_ADDR/PHYS_LOAD_ADD are set to zero, what tiny-demo cell
config is set to
This opens up new possibilities for Zephyr, so that usages beyond just
MCUs come to the table. I see special demand coming from
functional-safety related use cases on industry, automotive, etc.
[1] https://github.com/siemens/jailhouse
Reference to Jailhouse's booting preamble code:
Origin: Jailhouse
License: BSD 2-Clause
URL: https://github.com/siemens/jailhouse
commit: 607251b44397666a3cbbf859d784dccf20aba016
Purpose: Dual-licensing of inmate lib code
Maintained-by: Zephyr
Signed-off-by: Gustavo Lima Chaves <gustavo.lima.chaves@intel.com>
Add support for nrf52 series SOC. This patch Adds :-
1. Architecture specific Power Management APIs.
2. APIs for invoking various Power Management tasks into nrf52.
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Remove defines for IRQs we don't use. We should be getting this from DT
so this gives us a list of what we need to cleanup. Remove various
memory address offset defines to the ones we actually use.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds CONFIG_EXECUTE_XOR_WRITE, which is enabled by default on
systems that support controlling whether a page can contain executable
code. This is also known as W^X[1].
Trying to add a memory domain with a page that is both executable and
writable, either for supervisor mode threads, or for user mode threads,
will result in a kernel panic.
There are few cases where a writable page should also be executable
(JIT compilers, which are most likely out of scope for Zephyr), so an
option is provided to disable the check.
Since the memory domain APIs are executed in supervisor mode, a
determined person could bypass these checks with ease. This is seen
more as a way to avoid people shooting themselves in the foot.
[1] https://en.wikipedia.org/wiki/W%5EX
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This should clear up some of the confusion with random number
generators and drivers that obtain entropy from the hardware. Also,
many hardware number generators have limited bandwidth, so it's natural
for their output to be only used for seeding a random number generator.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Some "random" drivers are not drivers at all: they just implement the
function `sys_rand32_get()`. Move those to a random subsystem in
preparation for a reorganization.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The CLOCK_CONTROL config option is already defined in
drivers/clock_control, so there's no need to redefine it in arch/.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In PAE boot tables the __mmu_tables_start points to page directory
pointer (PDPT). Enable the PAE by updating the CR4.PAE and
IA32_EFER.NXE bits.
JIRA:ZEP-2511
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Created structures and unions needed to enable the software to
access these tables.
Also updated the helper macros to ease the usage of the MMU page
tables.
JIRA: ZEP-2511
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
If CONFIG_X86_PAE_MODE is enabled for the build, then gen_mmu.py
would generate the boot time page tables in PAE format.
This supports 3 level paging i.e Page Directory Pointer(PDPT), Page
Directory(PD) and Page Table(PT). Each Page Table Entry(PTE) maps to
a 4KB region. Each Page Directory Entry(PDE) maps a 2MB region.
Each Page Directory Pointer Entry(PDPTE) maps to a 1GB region.
JIRA: ZEP-2511
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Page Address Extension(PAE) page tables would be used
if this option is enabled.
JIRA:ZEP-2511
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Some SOCs (e.g. STM32F0) can map the flash to address 0 and
the flash base address at the same time. Prevent writing to
duplicate flash address which stops the SOC.
Allow Cortex M SOCs to create their own vector table relocation
function.
Provide a relocation function for STM32F0x SOCs.
Fixes#3923
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Match change we made to how I2C is enabled for other stm32 platforms:
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
During swap the required page tables are configured. The outgoing
thread's memory domain pages are reset and the incoming thread's
memory domain is loaded. The pages are configured if userspace
is enabled and if memory domain has been initialized before
calling swap.
GH-3852
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Added architecture specific support for memory domain destroy
and remove partition for arm and nxp. An optimized version of
remove partition was also added.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
STM32 UART driver was using a mix of LL/HAL APIs. This commit removes
calls to HAL API and replaces them with LL APIs. No functional change
have been seen during non regression testing.
But we could note a direct gain of 1Kb of ROM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Because the mcux shim drivers will soon depend on a clock control
interface, enable the mcux sim clock control driver by default on all
Kinetis SoCs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Currently this is defined as a k_thread_stack_t pointer.
However this isn't correct, stacks are defined as arrays. Extern
references to k_thread_stack_t doesn't work properly as the compiler
treats it as a pointer to the stack array and not the array itself.
Declaring as an unsized array of k_thread_stack_t doesn't work
well either. The least amount of confusion is to leave out the
pointer/array status completely, use pointers for function prototypes,
and define K_THREAD_STACK_EXTERN() to properly create an extern
reference.
The definitions for all functions and struct that use
k_thread_stack_t need to be updated, but code that uses them should
be unchanged.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Looking up the PTE flags was page faulting if the address wasn't
marked as present in the page directory, since there is no page table
for that directory entry.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This is a USB controller driver for STM32F4xx devices using
the STM32 Cube HAL_PCD framework. This has been tested with
the cdc_acm driver on a 96b_carbon board (STM32F401RE).
This is a refactoring of:
usb: usb_dc_stm: Add support for STM32Cube HAL_PCD USB driver
Signed-off-by: Christer Weinigel <christer@weinigel.se>
[daniel.thompson@linaro.org: Removed STM32F40(157) defconfig changes
together with STM32F4Discovery pinmux and defconfig changes, updated
clock settings and pad configuration to match latest mainline]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[giannis.damigos@gmail.com: Change uint*_t types to u*_t types,
change SYS_LOG_USB_DC_STM_LEVEL to SYS_LOG_USB_DRIVER_LEVEL and
update pinmux to match latest arm branch]
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
At very low optimization levels, the call to
K_THREAD_STACK_BUFFER doesn't get inlined, overflowing the
tiny stack.
Replace with _ARCH_THREAD_STACK_BUFFER() which on x86 is
just a macro.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Indicate to users that this feature isn't fully baked yet.
This will be reverted for 1.11 release.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Userspace is built on top of hardware stack protection and assumes
it is there. We can't enable this unless ARCH_HAS_USERSPACE is defined
anyway.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The Silicon Labs EFM32 Wonder Gecko MCU includes:
* Cortex-M4F core at 48MHz
* up to 256KB of flash and 32KB of RAM
* USB with host and OTG support
* multiple low power peripherals
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Also provide their prototypes in `soc.h`. This should help
readability, since some ROM functions, with their names as provided by
Espressif, have sometimes the same prefix as Zephyr APIs.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Use the define generated by the DTS instead of using the FLASH_ALIGN
alias. The latter is an internal mcuboot name. We shouldn't need it in
Zephyr itself.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This workaround fixes the issue that, after pin reset, RESETREAS bits
other than RESETPIN might also be set.
The workaround was added to both nRF52832 and nRF52840 SoCs.
Signed-off-by: Thiago Silveira <thiago@exati.com.br>
802.15.4 is the networking hardware available in KW41Z SoC (and
supported by Zephyr). So, if networking in enabled, automatically
select the corresponding driver. This is similar to how frdm_k64f
automatically selects Ethernet driver, 96b_carbon selects BLE/IPSP
drivers, etc. (But we apply it on SoC level to reuse across the
boards.)
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
For 'rep stosl' ECX isn't a size value, it's how many times to repeat
the 4-byte string copy operation.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Some our Zephyr tools don't like seeing UTF-8 characters, as reported in
issue #4131) so a quick scan and replace for UTF-8 characters in .rst,
.h, and Kconfig files using "file --mime-encoding" (excluding the /ext
folders) finds these files to tweak.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add the following application-facing memory domain APIs:
k_mem_domain_init() - to initialize a memory domain
k_mem_domain_destroy() - to destroy a memory domain
k_mem_domain_add_partition() - to add a partition into a domain
k_mem_domain_remove_partition() - to remove a partition from a domain
k_mem_domain_add_thread() - to add a thread into a domain
k_mem_domain_remove_thread() - to remove a thread from a domain
A memory domain would contain some number of memory partitions.
A memory partition is a memory region (might be RAM, peripheral
registers, flash...) with specific attributes (access permission,
e.g. privileged read/write, unprivileged read-only, execute never...).
Memory partitions would be defined by set of MPU regions or MMU tables
underneath.
A thread could only belong to a single memory domain any point in time
but a memory domain could contain multiple threads.
Threads in the same memory domain would have the same access permission
to the memory partitions belong to the memory domain.
The memory domain APIs are used by unprivileged threads to share data
to the threads in the same memory and protect sensitive data from
threads outside their domain. It is not only for improving the security
but also useful for debugging (unexpected access would cause exception).
Jira: ZEP-2281
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
- syscall.h now contains those APIs needed to support invoking calls
from user code. Some stuff moved out of main kernel.h.
- syscall_handler.h now contains directives useful for implementing
system call handler functions. This header is not pulled in by
kernel.h and is intended to be used by C files implementing kernel
system calls and driver subsystem APIs.
- syscall_list.h now contains the #defines for system call IDs. This
list is expected to grow quite large so it is put in its own header.
This is now an enumerated type instead of defines to make things
easier as we introduce system calls over the new few months. In the
fullness of time when we desire to have a fixed userspace/kernel ABI,
this can always be converted to defines.
Some new code added:
- _SYSCALL_MEMORY() macro added to check memory regions passed up from
userspace in handler functions
- _syscall_invoke{7...10}() inline functions declare for invoking system
calls with more than 6 arguments. 10 was chosen as the limit as that
corresponds to the largest arg list we currently have
which is for k_thread_create()
Other changes
- auto-generated K_SYSCALL_DECLARE* macros documented
- _k_syscall_table in userspace.c is not a placeholder. There's no
strong need to generate it and doing so would require the introduction
of a third build phase.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
SoCs outside the Kinetis family can have the TRNG module, so move the
HAS_TRNG config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the RNGA module, so move the
HAS_RNGA config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the FTM module, so move the
HAS_FTM config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Note that 'select HAS_FTM' was previously missing from Kconfig.soc and
is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the ADC16 module, so move the
HAS_ADC16 config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the LPSCI module, so move the
HAS_LPSCI config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the LPUART module, so move the
HAS_LPUART config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Move all QEMU related defines to the boards and cleanup xtensa platforms
which were marked to be QEMU capable by mistake.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
mcuboot_constraints.h had FLASH information related to the SoC that
should be maintained as part of the SoC and not in the subsystem. Also
fixed Makefiles to check for IMG_UTIL Kconfig and not MCUBOOT.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A quick look at "man syscall" shows that in Linux, all architectures
support at least 6 argument system calls, with a few supporting 7. We
can at least do 6 in Zephyr.
x86 port modified to use EBP register to carry the 6th system call
argument.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
* Instead of a common system call entry function, we instead create a
table mapping system call ids to handler skeleton functions which are
invoked directly by the architecture code which receives the system
call.
* system call handler prototype specified. All but the most trivial
system calls will implement one of these. They validate all the
arguments, including verifying kernel/device object pointers, ensuring
that the calling thread has appropriate access to any memory buffers
passed in, and performing other parameter checks that the base system
call implementation does not check, or only checks with __ASSERT().
It's only possible to install a system call implementation directly
inside this table if the implementation has a return value and requires
no validation of any of its arguments.
A sample handler implementation for k_mutex_unlock() might look like:
u32_t _syscall_k_mutex_unlock(u32_t mutex_arg, u32_t arg2, u32_t arg3,
u32_t arg4, u32_t arg5, void *ssf)
{
struct k_mutex *mutex = (struct k_mutex *)mutex_arg;
_SYSCALL_ARG1;
_SYSCALL_IS_OBJ(mutex, K_OBJ_MUTEX, 0, ssf);
_SYSCALL_VERIFY(mutex->lock_count > 0, ssf);
_SYSCALL_VERIFY(mutex->owner == _current, ssf);
k_mutex_unlock(mutex);
return 0;
}
* the x86 port modified to work with the system call table instead of
calling a common handler function. fixed an issue where registers being
changed could confuse the compiler has been fixed; all registers, even
ones used for parameters, must be preserved across the system call.
* a new arch API for producing a kernel oops when validating system call
arguments added. The debug information reported will be from the system
call site and not inside the handler function.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
- _arch_user_mode_enter() implemented
- _arch_is_user_context() implemented
- _new_thread() will honor K_USER option if passed in
- System call triggering macros implemented
- _thread_entry_wrapper moved and now looks for the next function to
call in EDI
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
- There's no point in building up "validity" (declared volatile for some
strange reason), just exit with false return value if any of the page
directory or page table checks don't come out as expected
- The function was returning the opposite value as its documentation
(0 on success, -EPERM on failure). Documentation updated.
- This function will only be used to verify buffers from user-space.
There's no need for a flags parameter, the only option that needs to
be passed in is whether the buffer has write permissions or not.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We shouldn't be imposing any policy here, we do not yet use these in
Zephyr. Zero these at boot and otherwise leave alone.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
stm32f417xe and stm32f417xg have been introduced with 2
different defconfig files. Since same code is declared
in both files, mutualize declarations in a single file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The enumerations stm32{f3,f4}x_pin_config_mode aren't used any
more. This patch removes them.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
In various places, a private _thread_entry_t, or the full prototype
were being used. Be consistent and use the same typedef everywhere.
Signen-off-by: Andrew Boie <andrew.p.boie@intel.com>
Indenting preprocessor directives reduces the code readability, because
it make preprocessor directives harder to spot.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add flash page layout support for STM32F4 SoCs.
This almost eliminates the need for flash_map.h, except for
STM32F4X_SECTOR_MASK, so delete the file and move the define into the
F4 implementation, to keep things simple.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Helper macros to ease the usage of the MMU page table structures.
Added Macros to get Page table address and Page Table Entry
values.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Most x86 exceptions that don't already have their own handlers
are fairly rare, but with the introduction of userspace
people will be seeing General Protection Faults much more
often. Report it as text so that users unfamiliar with x86
internals will know what is happening.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Previously, this was only done if an essential thread self-exited,
and was a runtime check that generated a kernel panic.
Now if any thread has k_thread_abort() called on it, and that thread
is essential to the system operation, this check is made. It is now
an assertion.
_NANO_ERR_INVALID_TASK_EXIT checks and printouts removed since this
is now an assertion.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Years of iterative development had made this function more complicated
than it needed to be. Fixed some errors in the documentation as well.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
All system calls made from userspace which involve pointers to kernel
objects (including device drivers) will need to have those pointers
validated; userspace should never be able to crash the kernel by passing
it garbage.
The actual validation with _k_object_validate() will be in the system
call receiver code, which doesn't exist yet.
- CONFIG_USERSPACE introduced. We are somewhat far away from having an
end-to-end implementation, but at least need a Kconfig symbol to
guard the incoming code with. Formal documentation doesn't exist yet
either, but will appear later down the road once the implementation is
mostly finalized.
- In the memory region for RAM, the data section has been moved last,
past bss and noinit. This ensures that inserting generated tables
with addresses of kernel objects does not change the addresses of
those objects (which would make the table invalid)
- The DWARF debug information in the generated ELF binary is parsed to
fetch the locations of all kernel objects and pass this to gperf to
create a perfect hash table of their memory addresses.
- The generated gperf code doesn't know that we are exclusively working
with memory addresses and uses memory inefficently. A post-processing
script process_gperf.py adjusts the generated code before it is
compiled to work with pointer values directly and not strings
containing them.
- _k_object_init() calls inserted into the init functions for the set of
kernel object types we are going to support so far
Issue: ZEP-2187
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In benchmark test (test_info) while making function call regs
r0 - r4 are modified into called function. Due to this value
inside r3 is getting lost.
This patch saves and restore the value in r0-r4 regs while making
function calls from assembly language.
Jira: ZEP-2314
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
The API/Variable names in timing_info looks very speicific to
platform (like systick etc), whereas these variabled are used
across platforms (nrf/arm/quark).
So this patch :-
1. changing API/Variable names to generic one.
2. Creating some of Macros whose implimentation is platform
depenent.
Jira: ZEP-2314
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
This patch fixes a couple of issues with the stack guard size and
properly constructs the STACK_ALIGN and STACK_ALIGN_SIZE definitions.
The ARM AAPCS requires that the stack pointers be 8 byte aligned. The
STACK_ALIGN_SIZE definition is meant to contain the stack pointer
alignment requirements. This is the required alignment at public API
boundaries (ie stack frames).
The STACK_ALIGN definition is the required alignment for the start
address for stack buffer storage. STACK_ALIGN is used to validate
the allocation sizes for stack buffers.
The MPU_GUARD_ALIGN_AND_SIZE definition is the minimum alignment and
size for the MPU. The minimum size and alignment just so happen to be
32 bytes for vanilla ARM MPU implementations.
When defining stack buffers, the stack guard alignment requirements
must be taken into consideration when allocating the stack memory.
The __align() must be filled in with either STACK_ALIGN_SIZE or the
align/size of the MPU stack guard. The align/size for the guard region
will be 0 when CONFIG_MPU_STACK_GUARD is not set, and 32 bytes when it
is.
The _ARCH_THREAD_STACK_XXXXXX APIs need to know the minimum alignment
requirements for the stack buffer memory and the stack guard size to
correctly allocate and reference the stack memory. This is reflected
in the macros with the use of the STACK_ALIGN definition and the
MPU_GUARD_ALIGN_AND_SIZE definition.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch removes the redundant stack alignment check being done. The
stack definition macros enforce the alignment requirements via the
__align() directives.
In addition, fix the rounding down of the psp to be correct. The
actual initial stack pointer is the end of the stack minus the size of
the __esf structure. Rounding down after the subtraction will get us
to the correct offset.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
For some reason, the ESP32 HAL defines XCHAL_EXCM_LEVEL to 3. This
enables a version of _Level4Vector that doesn't work on this hardware.
Without complete visibility if the version that should work be axed,
keep both in the tree, but build the working other version instead
if building for ESP32.
Jira: ZEP-2556
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
When we mask out the GPIO High impedance/Pull-up/Pull-down field we
should be shifting the mask file, not shifting the field. This is
because all the other defines already assume the shift.
Coverity-CID: 173640
Jira: ZEP-2538
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Esp-idf defines the BIT macro that is also defined in Zephyr's
misc/util.h. Fix the issue by including the esp-idf headers first, so
that a check in util.h won't redefine the macro if it's already
defined.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
* apply STACK_GUARD_SIZE, no extra space will be added if
MPU_STACK_GUARD is disabled
* When ARC_STACK_CHECKING is enabled, MPU_STACK_GUARD will be
disabled
* add two new api: arc_core_mpu_default and arc_core_mpu_region
to configure mpu regions
* improve arc_core_mpu_enable and arc_core_mpu_disable
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* add arc mpu driver
* modify the corresponding kconfig and kbuild
* currently only em_starterkit 2.2's em7d configuration
has mpu feature (mpu version 2)
* as the minimum region size of arc mpu version 2 is 2048 bytes and
region size should be power of 2, the stack size of threads
(including main thread and idle thread) should be at least
2048 bytes and power of 2
* for mpu stack guard feature, a stack guard region of 2048 bytes
is generated. This brings more memory footprint
* For arc mpu version 3, the minimum region size is 32 bytes.
* the codes are tested by the mpu_stack_guard_test and stackprot
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Per ZEP-1958, Phase 2 of adding CC3220sf LaunchXL support,
was to "deprecate the CC3200 launchxl support in Zephyr
(redundant to the CC3220)."
Effectively, the CC3220 SOC replaces the CC3200.
This patch removes the following:
* the imported CC3200 SDK
* CC3200 SOC, board, DTS files.
* adjusts other files where cc3200 was mentioned.
Also, it fixes explicit references to CC3200 in generic
CC32xx driver files.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
- .text, .text.*, .literal, .literal.* had no matching input section
rule and were being passed to the output binary verbatim. These
are all now in the output "text" section as intended.
- various rules in the data section were unnecessarily using KEEP().
- SW_ISR_TABLE wasn't included in linker script anywhere and was
ending up in its own section, and not the data section as intended.
- noinit section didn't exist at all, now defined.
Issue: ZEP-2508
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Previously, calling NVIC_SetPriority(IRQn_Type irqn, ....) with
the NWP interrupt number of 171 caused a hard fault during a
subsequent svc #0 instruction during _Swap().
GNU compiler is generating a bit extension instruction (sxtb) which
converts a positive IRQ value argument to a negative value when
casting to the CMSIS IRQn_Type enum parameter type.
This generates a negative index, which then writes to an SCB
control register instead of NVIC register, causing a hard
fault later on.
This issue only occurs when passing interrupt numbers > 0x80
(eg: 171 (0xab) for the NWP) to the CMSIS NVIC apis.
The solution here is simply to redefine IRQn_Type to be an
unsigned 32 bit integer, while redefining the CMSIS IRQn_Type
enum definitions for interrupts less than zero.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
* add nested interrupt support for interrupts
+ use a varibale exc_nest_count to trace nest interrupt and exception
+ regular interrupts can be nested by regular interrupts and fast
interrupts
+ fast interrupt's priority is the highest, cannot be nested
* remove the firq stack and exception stack
+ remove the coressponding kconfig option
+ all interrupts (normal and fast) and exceptions will be handled
in the same stack (_interrupt stack)
+ the pros are, smaller memory footprint (no firq stack), simpler
stack management, simpler codes, etc.. The cons are, possible
10-15 instructions overhead for the case where fast irq nests
regular irq
* add the case of ARC in test/kernel/gen_isr_table
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
When you build application for em starterkit 2.3 em7d, it will
report error during build since it is not supported currently.
Signed-off-by: Huaqi Fang <huaqi.fang@synopsys.com>
em starterkit has two versions, 2.2 and 2.3.
Change soc.h to support both versions,
main changes are the interrupt connections.
Signed-off-by: Huaqi Fang <huaqi.fang@synopsys.com>
Since em starterkit has different firmware versions(2.2 and 2.3),
but the EM7D of 2.3 has new secureshield feature, which is not supported
in Zephyr, but EM7D of 2.2 is a normal EM core, which can be supported,
so we add support for 2.2 EM7D.
Signed-off-by: Huaqi Fang <huaqi.fang@synopsys.com>
An abnormal crash was encountered in ARMv6-M SoCs that don't have flash
starting at 0. With Zephyr OS the reason for this crash is that, on
ARMv6-M the system requires an exception vector table at the 0 address.
We implement the relocate_vector_table function to move the vector table
code to address 0 on systems which don't have the start of code already
at 0.
[kumar.gala: reworderd commit message, tweaked how we check if we need
to copy vector table]
Signed-off-by: Xiaorui Hu <xiaorui.hu@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have an mcux shim driver, remove the old k64-specific
driver. Also remove include/drivers/k20_sim.h, since the old
k64-specific driver was the only thing left using it.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Switches the default pwm driver from the k64-specific driver to the
mcux shim, which can be used on other SoCs with the ftm peripheral.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux ftm driver to adapt it to the Zephyr
pwm interface.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This cleans up the exception handling by removing the table declaration
from xtensa_intr_asm.S, and removing the unused
_xt_set_exception_handler() function.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The Xtensa port was the only one remaining to be converted to the new
way of connecting interrupts in Zephyr. Some things are still
unconverted, mainly the exception table, and this will be performed
another time.
Of note: _irq_priority_set() isn't called on _ARCH_IRQ_CONNECT(), since
IRQs can't change priority on Xtensa: while the architecture has the
concept of interrupt priority levels, each line has a fixed level and
can't be changed.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Dynamic IRQ allocation has been yanked from Zephyr a few releases ago,
so there's no point in keeping these options available.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This provides basic GPIO support, with interrupts, and the ability to
read and write to ports on a pin-by-pin basis.
Jira: ZEP-2286
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This patch adjusts the ARM MPU implementation to be compliant to the
recent changes that introduced the opaque kernel data types.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The mimimum mpu size is 32 bytes, but requires mpu base address to be
aligned on 32 bytes to work. Define architecture thread macro when
MPU_STACK_GUARD config to allocate stack with 32 more bytes.
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
In the stm32_gpio_flags_to_conf function the configuration
values of the GPIO pin are shifted two times. One in the
stm32-pinctrlf1 header and one in the function. This patch
removes one of those shifts.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The value of the PTE (starting_pte_num) was not
calulated correctly. If size of the buffer exceeded 4KB,
the buffer validation API was failing.
JIRA: ZEP-2489
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds the allow flash write CONFIG option to the ARM MPU
configuration in privileged mode.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: David Brown <david.brown@linaro.org>
This patch adds the allow flash write CONFIG option to the NXP MPU
configuration in privileged mode.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: David Brown <david.brown@linaro.org>
Currently Thread time slice is getting reset at end of timer
interrupt. Due to which equal priority threads behind current thread
in ready_q are not getting chance to run and leading to starvation.
This patch handles time slice in _ExcExit section context switch is
required.
Jira: ZEP-2444
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
As luck would have it, the TSS for the main IA task has
all the information we need, populate an exception stack
frame with it.
The double-fault handler just stashes data and makes the main
hardware thread runnable again, and processing of the
exception continues from there.
We check the first byte before the faulting ESP value to see
if the stack pointer had run up to a non-present page, a sign
that this is a stack overflow and not a double fault for
some other reason.
Stack overflows in kernel mode are now recoverable for non-
essential threads, with the caveat that we hope we weren't in
a critical section updating kernel data structures when it
happened.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Configuring the RAM/ROM regions will be the same for all
x86 targets as this is done with linker symbols.
Peripheral configuration left at the SOC level.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The CPU first checks the page directory entry for write
or user permissions on a particular page before looking
at the page table entry.
If a region configured all pages to be non user accessible,
and this was changed for a page within it to be accessible,
the PDE would not be updated and any access would still
return a page fault.
The least amount of runtime logic to deal with this is to
indicate at build time that some pages within a region may
be marked writable or user accessible at runtime, and to
pre-set the flags in the page directory entry accordingly.
The driving need for this is the region configuration for
kernel memory, which will have user permissions set at
runtime for stacks and user-configured memory domains.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Page faults will additionally dump out some interesting
page directory and page table flags for the faulting
memory address.
Intended to help determine whether the page tables have been
configured incorrectly as we enable memory protection features.
This only happens if CONFIG_EXCEPTION_DEBUG is turned on.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The ouput speed of the gpio pins passed via the 'conf' argument was
ignored, causing the speed to always be in its reset state (lowest
possible speed for most pins). This was causing problems for pins that
actually need a speed faster than the default, like the ethernet
controller pins.
Combined with the correct pinmux configuration this fixes problems
of the olimex_stm32_e407 board not being able to send ethernet data.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Historically, stacks were just character buffers and could be treated
as such if the user wanted to look inside the stack data, and also
declared as an array of the desired stack size.
This is no longer the case. Certain architectures will create a memory
region much larger to account for MPU/MMU guard pages. Unfortunately,
the kernel interfaces treat both the declared stack, and the valid
stack buffer within it as the same char * data type, even though these
absolutely cannot be used interchangeably.
We introduce an opaque k_thread_stack_t which gets instantiated by
K_THREAD_STACK_DECLARE(), this is no longer treated by the compiler
as a character pointer, even though it really is.
To access the real stack buffer within, the result of
K_THREAD_STACK_BUFFER() can be used, which will return a char * type.
This should catch a bunch of programming mistakes at build time:
- Declaring a character array outside of K_THREAD_STACK_DECLARE() and
passing it to K_THREAD_CREATE
- Directly examining the stack created by K_THREAD_STACK_DECLARE()
which is not actually the memory desired and may trigger a CPU
exception
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Move to using the generated IRQ defines from the DTS instead of soc.h.
This change also fixes a minor bug in that the error irq priority wasn't
getting correctly picked up from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32F3 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32F4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rework stm32f1 pinmux code for future dts based pinmux code
generation.
Pin configuration is now done directly thanks to gpio port
configuration. Reference to pseudo alternate functions are
now removed same as the use of pins[] array.
Pins function (uart tx for instance) is set implicitly by
defining gpio mode and configuration.
This behavior is specific to stm32f10x series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32L4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed and information is transferred to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In L4 series, select HAS_STM32CUBE is done per soc.
This could be factorized in Kconfig.series.
Aim is to lower the steps to add a new SoC.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that we generate BLUETOOTH_UART_ON_DEV_NAME, UART_PIPE_ON_DEV_NAME,
and BLUETOOTH_MONITOR_ON_DEV_NAME Kconfig defines for dts enabled
platforms add those into the appropriate dts files and remove from the
various board/Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This will trigger a page fault if the guard area
is written to. Since the exception itself will try
to write to the memory, a double fault will be triggered
and we will do an IA task switch to the df_tss and panic.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Subsequent patches will set this guard page as unmapped,
triggering a page fault on access. If this is due to
stack overflow, a double fault will be triggered,
which we are now capable of handling with a switch to
a know good stack.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We now create a special IA hardware task for handling
double faults. This has a known good stack so that if
the kernel tries to push stack data onto an unmapped page,
we don't triple-fault and reset the system.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We will need this for stack memory protection scenarios
where a writable GDT with Task State Segment descriptors
will be used. The addresses of the TSS segments cannot be
put in the GDT via preprocessor magic due to architecture
requirments that the address be split up into different
fields in the segment descriptor.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This has one use-case: configuring the double-fault #DF
exception handler to do an IA task switch to a special
IA task with a known good stack, such that we can dump
diagnostic information and then panic.
Will be used for stack overflow detection in kernel mode,
as otherwise the CPU will triple-fault and reset.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This is one less host tool we have to compile for every build,
and makes the build tools more portable across host OSes.
The code is also much simpler to maintain.
Issue: ZEP-2063
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This enables the MMU-based stack protection feature,
which will cause a fatal error if a thread overflows
its stack in kernel mode, at a nontrivial cost in memory
(4K per thread).
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This will cause sanitycheck runs to finish more quickly
instead of sitting there waiting on a timeout. We already
do this with the Xtensa simulator.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
With introduction of commit "pinmux: stm32: directly return error if
stm32_get_pin_config fails", pin configuration fails when
pins are not configured in pins[] array.
This was the case for configuration UART1 assigned on PB6/PB7.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
'commit
("devicetree: Generate BLUETOOTH_UART ,UART_PIPE etc config from dt")'
created a dependency of selecting UART_QMSI_0 on device tree.
This change is reverted as it incorrect.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
If the adc driver configuration is enabled (CONFIG_ADC=y), then enable
the mcux shim driver by default for all Kinetis SoCs.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux adc16 driver to adapt it to the Zephyr
adc interface.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
patch uses chosen property zephyr,bt-uart, zephyr,uart-pipe
and zephyr,bt-mon-uart to determine the uart instance to be
used for bluetooth,uart_pipe and bluetooth_monitor and generate
appropriate configs.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
A user space buffer must be validated before required operation
can proceed. This API will check the current MMU
configuration to determine if the buffer held by the user is valid.
Jira: ZEP-2326
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
This needs to be in <arch/cpu.h> so that it can be called
from the k_panic()/k_oops() macros in kernel.h.
Fixes build errors on these arches when using k_panic() or
k_oops().
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We can use the chosen property "zephyr,console" to determine what uart
should be used as the console and find its name to generate a define for
CONFIG_UART_CONSOLE_ON_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This breaks too easily, for example if &some_linker_variable
is used. The names don't matter at all, use preprocessor
__COUNTER__.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Previously we were instantiating QEMU with 32MB of RAM but
only enabling a small fraction of it.
Now we boot with 8MB of ram. We ignore the first 4K so we can
make that an unmapped paged to catch NULL pointer dereferences.
If XIP is enabled, the "ROM" region will be the first half of
memory, the "RAM" region the latter.
Move the IDT_LIST and MMU_LIST regions elsewhere so they don't
overlap the new memory arrangement.
Use !XIP to fix a problem where CONFIG_RAM_SIZE was set incorrectly
for XIP case.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add a STM32 LL based driver for the RNG processor. The RNG processor
is a random number generator, based on a continuous analog noise, that
provides a random 32-bit value to the host when read. The RNG passed
the FIPS PUB 140-2 (2001 October 10) tests with a success ratio of 99%.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
By now, t0 register restored value is overwritten
by mepc and mstatus values prior to returning from ISR.
Fixed by restoring mstatus and mepc registers before
restoring the caller-saved registers.
As t0 is a temporary register within the riscv ABI,
this issue was unnoticed for most applications, except
for computation intensive apps, like crypto tests.
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
The defaults of 0x100000 for ROM and 0x400000 for RAM are intended
to 'fake' a XIP configuration, this all takes place in just RAM.
The gap between these two values is 3 megabytes, specify this
properly.
Fixes numerous test cases on qemu_x86 if CONFIG_XIP is enabled.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Enabled the boot_time test on ARM SoCs, set __start_time_stamp on ARM
since we don't have a free running counter similar to TSC on x86.
Also moved to printing the values out as %u to increase the range of
values.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch allows more generic USB configuration in the samples
and removes platform dependent driver configuration.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
In added mode flash operation are performed in timeslice
(in radio idle time).
Kconfig for mode enabling CONFIG_SOC_FLASH_NRF5_RADIO_SYNC.
Erase and write API implementations were rewritten and preserved against
concurrent execution.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Board port was done before the yaml transition, so was missing a
cc2650_sensortag.yaml. As such when we build all the test we get a few
build errors that we also fixed up.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add configuration, documentation, pinmux, fixup and dts support for
STM32F103x8 based Minimum System Development board.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Add configuration and memory definitions to support STM32F103x8
Medium-density performance line SoC with 64 KB Flash.
Merge multiple files into single Kconfig.defconfig.stm32f103xx
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Since not all socs from f3 series (i.e stm32f334x8 no MPU) have MPU
capability, add capability only for MPU capable socs in Kconfig.soc
JIRA: ZEP-2220
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
As other stm32 series support MPU, move common file in a file tree
useable by socs from other series
JIRA: ZEP-2220
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
patch adds necessary files and does the modification to the existing
files to add device support for x86 based intel quark microcontroller
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
The first stage bootloader, part of the ESP32 ROM, already sets up
a stack that's sufficient to execute C programs. So, instead of
implementing __stack() in assembly, do it in C to simplify things
slightly.
This ESP32-specific initialization will perform the following:
- Disable the watchdog timer that's enabled by the bootloader
- Move exception handlers to IRAM
- Disable normal interrupts
- Disable the second CPU
- Zero out the BSS segment
Things that might be performed in the future include setting up the
CPU frequency, memory protection regions, and enabling the flash
cache.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Unconditionally use CONFIG_SIMULATOR_XTENSA to determine if XT_SIMULATOR
or XT_BOARD should be defined.
If CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC, also define XT_CLOCK_FREQ. This
isn't ideal as the clock frequency might be changed in runtime and this
effectively makes it a constant.
Until we can control the clock frequency in runtime, this will suffice.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This is a minimal driver enabling console output during the port
bringup. While the driver works, only one of the three UART devices
are supported, and there isn't any way to change any parameters or
use interrupts. This will most likely be superceded by a proper
driver after the port has matured.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Due to the configurable nature of the Xtensa platform, the generic name of
"LX6" cannot be used to describe an SoC as far as Zephyr goes. So ESP32 is
defined both as a SoC and as a board.
This is based on work by Rajavardhan Gundi.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
We always have UART_IRQ_FLAGS set to 0, so just call IRQ_CONNECT with a
0 argument for the flags, and remove the UART_IRQ_FLAGS. This is
towards support for using the driver on the TI CC2650. (we add a
comment about that as well).
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Clearing fields in the region descriptor attributes doesn't always have
the expected effect of revoking permissions. In the case of bus master
supervisor mode fields (MxSM), setting to zero actually enables read,
write, and execute access.
When we reworked handling of region descriptor 0, we inadvertently
enabled execution from RAM by clearing the MxSM fields and enabling the
descriptor. This caused samples/mpu_test run to throw a usage fault
instead of an MPU-triggered bus fault.
Fix this by setting all the MxSM fields to 2'b11, which gives supervisor
mode the same access as user mode.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
1. Changed _tsc_read() to k_cycles_get_32(). Thus reading the
time stamp will be agnostic of the architecutre used.
2. Changed the variable names from *_tsc to *_time_stamp.
JIRA: ZEP-1426
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Add a separate section in the linker to place the MMU configuration
information. This location is read by the gen_mmu.py script to
create the actual page tables.
JIRA: ZEP-2095
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
In crt0.S the MMU is initialized. It uses the statically build
page tables. Here 32-bit paging scheme is used, thereby each page
table entry maps to a 4KB page. The valid regions of the memory are
specified by SOC specific file(soc.c).
JIRA: ZEP-2099
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Makefile rule to create the MMU page tables at boot time. This
rule invokes the gen_mmu.py script to create a binary which is
then placed into the kernel image using objcopy.
Makefile.mmu is included only when CONFIG_X86_MMU is enabled.
JIRA: ZEP-2095
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Macro is used to create a structure to specify the boot time
page table configuration. Needed by the gen_mmu.py script to generate
the actual page tables.
Linker script is needed for the following:
1. To place the MMU page tables at 4KByte boundary.
2. To keep the configuration structure created by
the Macro(mentioned above).
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Kconfig definition for enabling the memory management Unit
on x86 based platforms.
JIRA: ZEP-2093
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
The .balign directives were not working correctly in their
previous positions as the directive was applying to the section
before the variable's section, causing in some builds the
variables to be misaligned, and accesses to them causing faults.
With the alignments after the section declaration, the variables
will now be aligned as specified. Any future variable declarations
should use this form instead to ensure proper alignment.
Signed-off-by: Michael R Rosen <michael.r.rosen@intel.com>
Both the ARM and NXP MPU drivers incorrectly calculated the region index
by assuming the region type (e.g., THREAD_STACK_GUARD_REGION) was
zero-indexed, when in reality it is one-indexed. This had the effect of
wasting one region.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The NXP MPU requires special handling of region descriptor 0 to
guarantee that the debugger has access to the entire address space. It
does not allow writes from the core to affect the start or end
addresses, or the permissions associated with the debugger.
The original implementation of this driver attempted to work around
region descriptor 0, resulting in an off-by-1 error caught by Coverity.
Instead, define region descriptor 0 explicitly in the mpu_regions array,
and add some asserts to ensure that one doesn't try to change its start
or end addresses. This has an added benefit such that more permissions
can be enabled in region 0 if desired, whereas the previous
implementation always forced all writable permissions to be cleared.
Coverity-CID: 170473
Jira: ZEP-2258
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The original implementation of _get_num_regions() parsed the CESR[NRGD]
register field to determine the number of mpu region descriptors
implemented in hardware. There was a possible path in the code to return
zero, which would cause underflow later on in arm_core_mpu_configure().
Coverity complained despite an assert to catch this condition. Instead,
use a preprocessor macro from mcux that defines the number of mpu region
descriptors.
Coverity-CID: 169811
Jira: ZEP-2208
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Stack sentinel doesn't prevent corruption, it just notices when
it happens. Any memory could be in a bad state and it's more
appropriate to take the entire system down rather than just kill
the thread.
Fatal testcase will still work since it installs its own
_SysFatalErrorHandler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
One of the stack sentinel policies was to check the sentinel
any time a cooperative context switch is done (i.e, _Swap is
called).
This was done by adding a hook to _check_stack_sentinel in
every arch's __swap function.
This way is cleaner as we just have the hook in one inline
function rather than implemented in several different assembly
dialects.
The check upon interrupt is now made unconditionally rather
than checking if we are calling __swap, since the check now
is only called on cooperative _Swap(). The interrupt is always
serviced first.
Issue: ZEP-2244
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The REGION bits (bit[3:0]) of MPU_RBAR register can specify the number
of the region to update if the VALID bit (bit[4]) is also set.
If the bit[3:0] of "region_addr" are not zero, might cause to update
unexpected region. This could happen since we might not declare stack
memory with specific alignment.
This patch will mask the bit[4:0] of "region_addr" to prevent updating
unexpected region.
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
The kernel tracks time slice usage with the _time_slice_elapsed global.
Every time the timer interrupt goes off and the timer driver calls
_nano_sys_clock_tick_announce() with the elapsed time, this is added to
_time_slice_elapsed. If it exceeds the total time slice, the thread is
moved to the back of the queue for that priority level and
_time_slice_elapsed is reset to zero.
In a non-tickless kernel, this is the only time _time_slice_elapsed is
reset. If a thread uses up a partial time slice, and then cooperatively
switches to another thread, the next thread will inherit the remaining
time slice, causing it not to be able to run as long as it ought to.
There does exist code to properly reset the elapsed count, but it was
only compiled in a tickless kernel. Now it is built any time
CONFIG_TIMESLICING is enabled.
Issue: ZEP-2107
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add necessary Kconfig and minimal device tree in order to support
STM32F412ZG variant as found on the Nucleo STM32F412 board.
Origin: Original
Change-Id: Ic98a686f478ce551dc6101466ed0cf16924109e8
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Following migration of stm32f1xx series clock control driver to
STM32Cube LL API, cleanup stm32 code base in order to take into
account that this is the only clock driver available for stm32
family.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following introduction of stm32cube LL based clock control driver,
remove references to former native driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Align stm32f1xx series clock driver to other parts of stm32 family.
Driver support both Connectivity and Density lines of stm32f1 series,
that are based on different Reset and Clock Control architectures.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The STM32F413ZH has 1536kB of Flash and 320kB of SRAM. This
configuration is currently not supported by ST MPU driver, so fill in
the blanks.
Note: The MPU does not support region size that is not a power-of-2 (see
the SIZE field in the MPU_RASR register). This is a problem for our
1536kB Flash region, so it was rounded up to the nearest choice. This is
possible because the memory in the range 0x0818000 - 0x0FFFFFFF is
"Reserved" and thus not mapped anyway.
Change-Id: If0c3d1db564ca45e77f8b5bafa2afdbafa85b40f
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
This reverts commit 37f4178f58.
This change builds gen_idt in the zephyr project tree instead of
building it in outdir of the application. The build process should all
happen inside outdir and no binaries should be placed in the zephyr
tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
pop {lr} instruction is not supported in ARMv6-M, fixed by
using pop {r0}; mov lr, r0; instructions.
Jira: ZEP-2222
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
We now have generic ARM M4 MPU support added to Zephyr.
Let's enable it for use with Nordic nRF52 chips.
Memory Layout was generated from Section 8.3 "Memory
Map" of nRF52 Product Specifications (for both nRF52832
and nRF52840):
0x00000000: Flash
0x10000000: Factory Information Config Registers
0x10001000: User Information Config Registers
0x20000000: SRAM
0x40000000: APB Peripherals
0x50000000: AHB Peripherals
0xE0000000: ARM M4 Private Peripheral Registers
NOT Configured:
0x60000000: External RAM
0x80000000: External RAM
0xA0000000: External Device
0xC0000000: External Device
NOTE: More work will be needed for future Nordic MWU (Memory
Watching Unit) support.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This patch add arm core MPU support to NXP MPU driver.
With this feature it is now possible to enable stack guarding on NXP
MPUs.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The STM32L4x SoCs embeds a slightly different embedded flash controller
from the STM32F4x SoCs.
This particular controller has the following properties :
- Up to 2 512KiB banks divided in 2KiB pages
- Flash can be accessed in any sizes
- Flash must be written in 64bit aligned 64bit double-words
The drivers/flash/flash_stm32f4x.c is refactored into a new common
drivers/flash/flash_stm32.c and drivers/flash/flash_stm32l4x.c is
created with the STM32L4x specific functions.
To ease the refactoring and keep common functions, the STM32L4x flash
headers are slightly modified to match the hardware reference naming
and solve compilation issues.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neither ASF nor CMSIS provide defines that can be processed by
the assembler. Exclude those from soc.h. Before this was done
incorrectly in board.h file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This patch converts Atmel sam3x MCU series to use register
header files from Atmel Software Framework (ASF) library.
By using ASF different Atmel SAM MCU series can use common
device drivers.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This patch adds support for remaining Atmel SAM MCU series,
like sam3x to the common GPIO driver. After this update
full SAM MCU family should be supported by the driver.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add configuration, dtsi and memory configuration fixup for the
STM32F469XI High Performance SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Here are the main changes:
* board: Update EMSK onboard resources such as Button, Switch and LEDs
+ update soc.h for em7d, em9d, em11d
+ update board.h for em_starterkit board
* arc: Add floating point support and code density support
+ add kconfig configuration
+ add compiler options
+ add register definitions, marcos, assembly codes
+ fixes in existing codes and configurations.
* arc: Update detailed board configurations for cores of emsk 2.3
* script: Provide arc_debugger.sh for debugging em_starterkit board
+ make BOARD=em_starterkit debug
This will start openocd server for emsk, and arc gdb will connect
to this debug server, user can run `continue` command if user just
want to run the application, or other commands if debugging needed.
+ make BOARD=em_starterkit debugserver
This will start an openocd debugger server for emsk, and user can
connect to this debugserver using arc gdb and do what they want to.
+ make BOARD=em_starterkit flash
This will download the zephyr application elf file to emsk,
and run it.
Signed-off-by: Huaqi Fang <huaqi.fang@synopsys.com>
Use TOOLCHAIN_VARIANT to indicate what XCC toolchain release
to use.
Set a reasonable default for the RG-2016.4 toolchain release.
D_108mini, D_212GP, D_233L are only in RF-2016.4, set that
appropriately.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This patch integrates the thread stack guard feature in the arm
Zephyr core.
Change-Id: I2022899cbc7a340be71cfaa52f79418292f93bae
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the arm core MPU implementation.
This implementation currently supports the thread stack guard feature.
Change-Id: I8b3795ebaf1ebad38aaddc2ed2f05535ead2c09a
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch add arm core MPU support to ARM MPU driver.
Change-Id: I5a61da4615ae687bf42f1c9947e291ebfd2d2c1d
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the arm core MPU interface, a common way to access the
pu functionalities by the arm zephyr kernel.
The interface can be divided in two parts:
- a core part that will be implemented by the arm_core_mpu driver and
used directly by the kernel
- a driver part that will be implemented by the mpu drivers and used by
the arm_core_mpu driver
Change-Id: I590bd284abc40d98b06fdf1efb5800903313aa00
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds initial MPU support to NXP K6x family.
The boot configuration prevents the following security issues:
* Prevent to read at an address that is reserved in the memory map.
* Prevent to write into the boot Flash/ROM.
* Prevent from running code located in SRAM.
This driver has been tested on FRDM-K64F.
Change-Id: I907168fff0c6028f1c665f1d3c224cbeec31be32
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
XCC doesn't recognize the "I" compiler constraint but GCC does. Switch
to "i" which is understood by both.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Now that all ARM platforms have a device tree we can move selecting of
HAS_DTS up and remove any !HAS_DTS cases, as well as setting in all the
defconfigs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add defines and pinmux arrays to support more UARTs on STM32F4.
Change-Id: Ib06c549bdb2b3d7065554a0a6d1a3d15441b29c9
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
It is useless to include the pinmux for a peripheral if it is not
enabled in the Kconfig. This is unnecessary and it increases the size of
the binary.
Define macros that will default to void if the associated Kconfig is not
enabled.
Change-Id: I0857fcef335c75b8bb6d537fd859f93d5be4a228
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Clean-up the pinmux arrays as a preparatory work before adding more
pinmuxes.
This is achieved by the following two actions:
- Define the PAD macro to simplify the [x - 1] = y construct
- Reorder the declartions by bank / pin to make it easier to
locate a pin among a high number of other pins, while minimizing the
risk of conflict when two people add a new declaration for two
different pins
Change-Id: I1ca0cc4f48bcd8cfd35b331e9821935f5c855876
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Add necessary Kconfig and minimal device tree in order to support
STM32F413xH variants as found on the Nucleo STM32F413 board.
Origin: Original
Change-Id: I60230c240d6acb610f16a02c62048d448476e9c5
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The bitfield determining the I/O direction already defines the pin
as either input or output, cannot be none or both at the same time
This issue was reported by Coverity
Coverity-CID: 151970
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Not all the boards (for instance the Nuclo F412) use USART1 or USART2.
Let each board enable these USARTs when really used.
Change-Id: Idfe79c724bd7b1ab154310b4a8234b52eef2298d
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Commit 87893ddf7ad4 ("soc: stm32f429zi: rename SOC config flag") renamed
SOC_STM32F429XX to SOC_STM32F429XI but the text of the option should be
changed as well to reflect this restriction in scope.
Change-Id: I2627b59f805e73d6c8a3534e0feec71a4269c9ab
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Commit 599149dfb831 ("soc: stm32f407xg: rename SOC config flag") renamed
SOC_STM32F407XX to SOC_STM32F407XG but the text of the option should be
changed as well to reflect this restriction in scope.
Change-Id: Id03529452f5ec7d7ffee214b152c4aa555e1208a
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Rename SOC_STM32F407XX to SOC_STM32F407XG to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file).
Change-Id: I0afa16e86b7c99b9e685004f96beeb888f9e7568
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename SOC_STM32F429XX to SOC_STM32F429XI to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file)
Change-Id: Id188b7703d2bce0a3ded09132ff0f205efa9c143
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename SOC_STM32L476XX to SOC_STM32L476XG to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file)
Change-Id: I834bb5b83c24c39e90c0492a2b22a7c7802de361
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The xC tag in the SoC reference indicates the flash size, use it in the
configuration to permit selection of correct flash size for dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch enables the generation of the ARM CMSDK UART base address
from the device tree.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This places a sentinel value at the lowest 4 bytes of a stack
memory region and checks it at various intervals, including when
servicing interrupts or context switching.
This is implemented on all arches except ARC, which supports stack
bounds checking directly in hardware.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
- There's no clear need to disable frame pointers if this feature is
used, remove this directive.
- The 'top' and 'base' terms are reversed. The 'base' is the high
address of the stack. The top is the lowest address, where we cannot
push further down. Fixup member and offset names to correspond to how
these terms are used in hardware documentation.
- Use correct pointers for stack top location
- Fatal exceptions now go through _NanoFatalErrorHandler to report the
faulting ip and thread.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
For various reasons its often necessary to generate certain
complex data structures at build-time by separate tools outside
of the C compiler. Data is populated to these tools by way of
special binary sections not intended to be included in the final
binary. We currently do this to generate interrupt tables, forthcoming
work will also use this to generate MMU page tables.
The way we have been doing this is to generatea "kernel_prebuilt.elf",
extract the metadata sections with objcopy, run the tool, and then
re-link the kernel with the extra data *and* use objcopy to pull
out the unwanted sections.
This doesn't scale well if multiple post-build steps are needed.
Now this is much simpler; in any Makefile, a special
GENERATED_KERNEL_OBJECT_FILES variable may be appended to containing
the filenames to the generated object files, which will be generated
by Make in the usual fashion.
Instead of using objcopy to pull out, we now create a linker-pass2.cmd
which additionally defines LINKER_PASS2. The source linker script
can #ifdef around this to use the special /DISCARD/ section target
to not include metadata sections in the final binary.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
None of this is currently necessary, the spurious interrupt
stubs and exception entry code is included in the binary just
fine. To make matters worse, some data referenced lives in the
.intList section which is completely stripped out of the binary.
If in the future we find certain essential functions are being
garbage collected when they should not be, the proper way to
mitigate this is with KEEP() directives in the linker script.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We had two assembly files to prepare for entry into C domain,
one intended for the simulator and one intended for real boards.
- Both files merged into a single crt1.S for either simulated or real
targets
- Extra logic to populate command line arguments from simulator removed,
we don't use it.
- BSS zeroing logic from crt1-boards.S used
- Reference to missing reset-unneeded.S removed
- exit() implementation moved to fatal.c, now invokes a kernel panic
if we are not running under the simulator
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Unline k_thread_spawn(), the struct k_thread can live anywhere and not
in the thread's stack region. This will be useful for memory protection
scenarios where private kernel structures for a thread are not
accessible by that thread, or we want to allow the thread to use all the
stack space we gave it.
This requires a change to the internal _new_thread() API as we need to
provide a separate pointer for the k_thread.
By default, we still create internal threads with the k_thread in stack
memory. Forthcoming patches will change this, but we first need to make
it easier to define k_thread memory of variable size depending on
whether we need to store coprocessor state or not.
Change-Id: I533bbcf317833ba67a771b356b6bbc6596bf60f5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
C library is not actually used by the xtensa port, we only need the
'exit' function. Implement 'exit' in crt1-* and drop remaining
references to the C library.
Change-Id: I8a562363956b4755a6b5baee7acf3726485e5ce3
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Add QEMU_CPU_TYPE for the sample_controller, so that zephyr image could
be run on QEMU with sample_controller core.
Change-Id: Id9e97a43c4b7921142289dcf97ff782993ca0463
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
XT_* macros are defined in xtensa HAL headers as xcc intrinsics. gcc
does not have any of these intrinsics. Replace XT_* macros with inline
assembly or provide gcc-compatible definitions.
Change-Id: If823ea8a7898a11a3a8363b17efdba27dee4c6a4
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
A bad rebase of a patch that moved these defines around
unintentionally reverted a necessary change to the coprocessor
save area.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The files for the Arduino Due needed to be updated to use the new
configuration when the SoC moved from the atmel_sam3 directory to
the atmel_sam/sam3x directory.
Jira: ZEP-2067
Signed-off-by: Justin Watson <jwatson5@gmail.com>
The FPGA on the MPS2 board implements 4 SBCon devices for I2C which are
connected to:
- a touchscreen controller
- the audio device (for configuration)
- both shield connectors
Change-Id: I55ca985e18b45d68f5e7421c4768dfc9bf2fcb3f
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Converted Stellaris UART driver over to utilize device tree generated
defines. Added a yaml description for the uart, and converted over the
ti_lm3s6965 SoC & qemu_cortex_m3 board port over to utilize it.
Change-Id: Ie20844eb63d2c68eb59ad4160f7f5b5a35e2943b
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a simple device tree for the TI lm3s6965 SoC and QEMU
Cortex-M3 board port. We get flash and memory base addresses and sizes
from the device tree as well as the ARM NVIC number of priority bits.
Change-Id: I4452b5543de7be55518997e54837ccbfd4f121df
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reorder config entries alphabetically to make it easier to add new ones.
Change-Id: Ib118405a150a408638232513fba7198b458ecfa7
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Now that all the nRF based board/SoCs have device trees, we can remove
the Kconfig bits that are now coming from device tree.
Change-Id: Ia1a870a50582d4109070d2833660f58fd6f8691f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree support for nRF51822 SoCs and Arduino 101-BLE,
Curie-BLE, BLE Nano, PCA10028-DK, and Quark-SE BLE boards. This
is minimal support for memory, flash, and UART.
Change-Id: I7e572bea537e384b6d66e520462f023ace0c9b35
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fixup the nRF52840-QIAA to allow getting its SRAM & FLASH sizes from
device tree.
Change-Id: I67ecd7da5f0472402064f158030d9f97f49d7d20
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Nothing calls _ScpMainOscEnable, so lets remove it and associated files
that aren't used anymore.
Change-Id: Ibe900d039c531c4da56baa673d309ee961b09e52
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Cleanup soc code to enable UART_MCUX_LPSCI to support UART0.
Change-Id: I173febffcffc902f228946124e0434f122a67607
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a shim layer around the mcux lpsci driver to adapt it to the Zephyr
serial interface.
Change-Id: I024f1605e3194f34bb57e8a121900e05b3085a82
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for STM32L475xG SoC as a preliminary for
Discovery IOT board support.
stm32l476.dtsi file is now including stm32l475.dtsi
since STM32L476 SoC is a STM32L475 SoC with LCD support
Change-Id: I7567255e4172231cbf4899474617ecae0cd68d64
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following activation of stm32 common clock driver for stm32f4 series
remove references to stm32f4 specific driver.
Change-Id: I372a0ea046007bcb34944d6b2b8880077583b1d3
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit disables native stm32f4x clock control
driver and enables stm32 LL clock control driver
for stm32f4 family
Jira: ZEP-2039
Change-Id: I98ba6c89c4a3a1f39658c5808cd47a2d1f344130
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit enables STM32Cube LL based driver for stm32f4 series.
This generic driver provides a unified API to clock driver for all
stm32 series.
LL API allows driver to be lightweight and to keep genericity across
stm32 family to ease further devlopment and maintenance.
Change-Id: Ie31ae8f433313787f9c9eda77de41925721d54dd
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The CC3220SF is a replacement for the CC3200 SoC, comprising
a network coprocessor and Cortex-M4 MPU.
This leverages the CC3220 SDK driver peripheral library in ROM,
and some files built from ext/hal/ti/.
Jira: ZEP-1958
Change-Id: I892b212c178e05d84ff1d716dde593ced653ae6d
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
This fixes ZEP-1955. The issue was that the interrupt stack frame only
allocates 4 registers. This means that if any window overflow happens,
only 4 registers can be saved. This implies that the interrupt handler
can not call functions other than using call4. If this rule is not
honored, then it will result in the registers being overwriting other
context information and thus a stack corruption.
The fix consists on using call4 for calling even t logger function,
which is by the way more optimal as the interrupt handler does not need
to save more than 4 registers when these functions are called.
Issue: ZEP-1955
Change-Id: Iacea626443d1d61d95a52253ac8ff15fc3722d2c
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
This was more or less transplanted from old Viper codebase (Zephyr's
ancestor which supported paging) and adapted to current coding style.
Change-Id: I203e631f1dcd5f2fb4e9a2fa9339fc7521c7962d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Adds event based scheduling logic to the kernel. Updates
management of timeouts, timers, idling etc. based on
time tracked at events rather than periodic ticks. Provides
interfaces for timers to announce and get next timer expiry
based on kernel scheduling decisions involving time slicing
of threads, timeouts and idling. Uses wall time units instead
of ticks in all scheduling activities.
The implementation involves changes in the following areas
1. Management of time in wall units like ms/us instead of ticks
The existing implementation already had an option to configure
number of ticks in a second. The new implementation builds on
top of that feature and provides option to set the size of the
scheduling granurality to mili seconds or micro seconds. This
allows most of the current implementation to be reused. Due to
this re-use and co-existence with tick based kernel, the names
of variables may contain the word "tick". However, in the
tickless kernel implementation, it represents the currently
configured time unit, which would be be mili seconds or
micro seconds. The APIs that take time as a parameter are not
impacted and they continue to pass time in mili seconds.
2. Timers would not be programmed in periodic mode
generating ticks. Instead they would be programmed in one
shot mode to generate events at the time the kernel scheduler
needs to gain control for its scheduling activities like
timers, timeouts, time slicing, idling etc.
3. The scheduler provides interfaces that the timer drivers
use to announce elapsed time and get the next time the scheduler
needs a timer event. It is possible that the scheduler may not
need another timer event, in which case the system would wait
for a non-timer event to wake it up if it is idling.
4. New APIs are defined to be implemented by timer drivers. Also
they need to handler timer events differently. These changes
have been done in the HPET timer driver. In future other timers
that support tickles kernel should implement these APIs as well.
These APIs are to re-program the timer, update and announce
elapsed time.
5. Philosopher and timer_api applications have been enabled to
test tickless kernel. Separate configuration files are created
which define the necessary CONFIG flags. Run these apps using
following command
make pristine && make BOARD=qemu_x86 CONF_FILE=prj_tickless.conf qemu
Jira: ZEP-339 ZEP-1946 ZEP-948
Change-Id: I7d950c31bf1ff929a9066fad42c2f0559a2e5983
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Future tickless kernel patches would be inserting some
code before call to Swap. To enable this it will create
a mcro named as the current _Swap which would call first
the tickless kernel code and then call the real __swap()
Jira: ZEP-339
Change-Id: Id778bfcee4f88982c958fcf22d7f04deb4bd572f
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Found out that the SAM3 series is not a single series. There are actully
3 different series, 3U, 3A, and 3X.
Origin: Original
Jira: ZEP-2067
Change-Id: I61cdc826cc32dbdd25b5e6bafaada062c8ae8417
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Historically, space for struct k_thread was always carved out of the
thread's stack region. However, we want more control on where this data
will reside; in memory protection scenarios the stack may only be used
for actual stack data and nothing else.
On some platforms (particularly ARM), including kernel_arch_data.h from
the toplevel kernel.h exposes intractable circular dependency issues.
We create a new per-arch header "kernel_arch_thread.h" with very limited
scope; it only defines the three data structures necessary to instantiate
the arch-specific bits of a struct k_thread.
Change-Id: I3a55b4ed4270512e58cf671f327bb033ad7f4a4f
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Moved the Atmel SAM 3 from its own directory into
the directory tree laid out in arch/arm/soc/atmel_sam.
Origin: Original
Jira: ZEP-2067
Change-Id: I26a1a521dd7caa607c3e95a06cd574ee68ca59b8
Signed-off-by: Justin Watson <jwatson5@gmail.com>
This SoC, in its default configuration, does not have any SW IRQ below
the EXCM level. This make it unsuitable to use irq_offload() and thus
almost untestable.
Decision was made to remove this configuration in favorof custom one
XRC_D2PM_5swIrq, which is the same core but with additional 4 SW IRQs
of level 1 and an additional timer.
Issue: ZEP-2029
Change-Id: Iee4f8346aa9d610e14898444f78d28ef0ac4cef2
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
This patch adds initial MPU support to STM32F401XE.
The boot configuration prevents the following security issues:
* Prevent to read at an address that is reserved in the memory map.
* Prevent to write into the boot Flash/ROM.
* Prevent the application to access to the BootROM.
* Prevent from running code located in SRAM.
Change-Id: I4dc0669009bd5c0a829a69f8ff417c787b7043ed
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds initial MPU support to ARM Beetle.
The boot configuration prevents the following security issues:
* Prevent to read at an address that is reserved in the memory map.
* Prevent to write into the boot Flash/ROM.
* Prevent from running code located in SRAM.
Change-Id: I64f1001369896fffb0647de6be605a95161c4695
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds an initial driver for the ARM MPU.
This driver has been tested on ARM Beetle and STM32F4.
Change-Id: I2bc4031961ec5a1d569929249237646f4a349f16
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch add the Memory Protection Unit parameter to the arm core
configuration.
Change-Id: Ifee8cdd5738391a6f182e8d0382d27eeb8c546ba
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Marc Moreno <marc.morenoberengue@linaro.org>
This patch adds the regions for the mpu configuration to the soc.h file.
Change-Id: Ifd1ce96eeb4731ae01f5171924af92b9e236a3dc
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Marc Moreno <marc.morenoberengue@linaro.org>
When calling scripts/gen_idt, if we don't have $ZEPHYR_BASE/scripts in
the path, it will fail, so we can call it with its full path to avoid
such need.
Change-Id: I47b340c9f3204ad8740c29e663e12082208bb13b
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Document the flash latency values by copying the relevant tables
from the reference manuals for each MCU.
Change-Id: Ieb2824ffd7634d917399e3e62146d9243b527f44
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Fix misspellings in Kconfig help text and made spelling of
RX and TX consistent (from reviewer comments)
Change-Id: Ie9d4c3863cd210e7a17b50a85a7e64156b6bf3d7
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
If the flash latency isn't set most STM32F4xx MCU's won't be able
to run from flash when the CPU frequency is changed. Make this a
compile time error instead of an assert at runtime.
Change-Id: Ic3421194545f8f83bd6e00f0cd011306c8d1eedd
Signed-off-by: Christer Weinigel <christer@weinigel.se>
Put the reason code in r0 and make a SVC #2 call, which will be
propagated to _fatal_error_handler as an exception.
The _is_in_isr() implementation had to be tweaked a bit. User-generated
SVC exception no longer just used for irq_offload(); just because we are
in it does not mean we are in interrupt context. Instead, have the
irq_offload code set and clear the offload_routine global; it will be
non-NULL only if it's in use. Upcoming changes to support memory
protection (which will require system calls) will need this too.
We free up some small amount of ROM deleting _default_esf struct as it's
no longer needed.
Issue: ZEP-843
Change-Id: Ie82bd708575934cffe41e64f5c128c8704ca4e48
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We reserve a specific vector in the IDT to trigger when we want to
enter a fatal exception state from software.
Disabled for drivers/build_all tests as we were up to the ROM limit
on Quark D2000.
Issue: ZEP-843
Change-Id: I4de7f025fba0691d07bcc3b3f0925973834496a0
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Unlike assertions, these APIs are active at all times. The kernel will
treat these errors in the same way as fatal CPU exceptions. Ultimately,
the policy of what to do with these errors is implemented in
_SysFatalErrorHandler.
If the archtecture supports it, a real CPU exception can be triggered
which will provide a complete register dump and PC value when the
problem occurs. This will provide more helpful information than a fake
exception stack frame (_default_esf) passed to the arch-specific exception
handling code.
Issue: ZEP-843
Change-Id: I8f136905c05bb84772e1c5ed53b8e920d24eb6fd
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The ICSR RETTOBASE bit is improperly implemented in QEMU (the polarity
is flipped) and the fix for it has not yet made it into a QEMU release,
although it is present in upstream master branch.
The symptom is that if we are not in thread mode, the system always
believes were are in a nested exception state, causing _IsInIsr() to
always return true.
Skip the nested exception check if we are building for QEMU.
This is a workaround until SDK-54 is resolved.
Issue: SDK-54
Change-Id: I06eafcc85fb76a9b23b4ba85ed6e111a08516231
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
For exceptions where we are just going to abort the current thread, we
need to exit handler mode properly so that PendSV can run and perform a
context switch. For ARM architecture this means that the fatal error
handling code path can indeed return if we were 1) in handler mode and
2) only wish to abort the current thread.
Fixes a very long-standing bug where a thread that generates an
exception, and should only abort the thread, instead takes down the
entire system.
Issue: ZEP-2052
Change-Id: Ib356a34a6fda2e0f8aff39c4b3270efceb81e54d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We do the same thing on all arch's right now for thread_monitor_init so
lets put it in a common place. This also should fix an issue on xtensa
when thread monitor can be enabled (reference to _nanokernel.threads).
Change-Id: If2f26c1578aa1f18565a530de4880ae7bd5a0da2
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We do a bit of the same stuff on all the arch's to setup a new thread.
So lets put that code in a common place so we unify it for everyone and
reduce some duplicated code.
Change-Id: Ic04121bfd6846aece16aa7ffd4382bdcdb6136e3
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There are a few places that we used an naked unsigned type, lets be
explicit and make it 'unsigned int'.
Change-Id: I33fcbdec4a6a1c0b1a2defb9a5844d282d02d80e
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types. This handles the remaining includes and kernel, plus
touching up various points that we skipped because of include
dependancies. We also convert the PRI printf formatters in the arch
code over to normal formatters.
Jira: ZEP-2051
Change-Id: Iecbb12601a3ee4ea936fd7ddea37788a645b08b0
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types. There are few places we dont convert over to the new
types because of compatiability with ext/HALs or for ease of transition
at this point. Fixup a few of the PRI formatters so we build with newlib.
Jira: ZEP-2051
Change-Id: I7d2d3697cad04f20aaa8f6e77228f502cd9c8286
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is a start to move away from the C99 {u}int{8,16,32,64}_t types to
Zephyr defined u{8,16,32,64}_t and s{8,16,32,64}_t. This allows Zephyr
to define the sized types in a consistent manor across all the
architectures we support and not conflict with what various compilers
and libc might do with regards to the C99 types.
We introduce <zephyr/types.h> as part of this and have it include
<stdint.h> for now until we transition all the code away from the C99
types.
We go with u{8,16,32,64}_t and s{8,16,32,64}_t as there are some
existing variables defined u8 & u16 as well as to be consistent with
Zephyr naming conventions.
Jira: ZEP-2051
Change-Id: I451fed0623b029d65866622e478225dfab2c0ca8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit should fix the concern about uninitialized memory of main
thread that was raised in https://gerrit.zephyrproject.org/r/#/c/12920/
The issue is more general, if it happens that the content of the
CPENABLE flag of any thread is set then any other thread using the CP
may cause a memory corruption.
I'd prefer to avoid the issue by initializing the CP descriptor to 0.
The descriptor itself is few words. We set them to 0 up to CP_ASA, which
is set to a real value.
As the dummy thread instantiated at the kernel startup does not use CP,
there is no CP area in its thread memory buffer. However it is mandatory
that it have the CP descriptor and that cpEnable in that descripot is
set to null. This is ensured by adding XT_CP_DESCR_SIZE to
_K_THREAD_NO_FLOAT_SIZEOF.
Change-Id: I6a36b5b363600ea1e6d98ab679981182b2b5a236
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
Move linker/common-rom.ld between .rodata sections so that it's together
with other immutable data.
Move linker/common-ram.ld before the .bss section, so that .bss does not
appear between data sections, which had two consequences:
- there's a .bss-sized gap in the ELF image, and
- PHDR segment that covers .bss overlaps the segment that covers .data,
resulting in the following xt-run warning:
( [ sample_controller ] load_bfd ) *WARNING* Executable segment
[ 60004d60, 600079a7 ] overlaps an existing executable segment
Change-Id: I2db46f4656e240016fe60883057cc000b6377180
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Fix doxygen comment typos used to generate API docs
Change-Id: I94df2e3a2bda248824ed2aeff3dd0eb743f0bf3e
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This reverts commit da8bff6b20.
We revert this as we intent to move away from {u}int{8,16,32,64}_t types
to our own internal types for sized variables so we shouldn't need the
PRI macros anymore.
Change-Id: Ibb1fae7500bddb4772b8830d497a0e5f78b44bcc
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To allow for various libc implementations (like newlib) in which the way
various {u}int{8,16,32}_t types are defined vary between both libc
implementations and across architectures we need to utilize the PRI
defines.
Change-Id: Ic4e65db52c8d693228cf80584283d4d06e68b5ad
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add soc_gpio_get(), soc_gpio_debounce_length_set() functions to Atmel
SAM soc_gpio driver.
Change-Id: I541c6fead9a308dd2e67c59dabe67b87cf1628ef
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added serial (UART) driver for Atmel SAM MCU family.
Note:
- Error handling is not implemented
- The driver works only in polling mode, interrupt mode is
not implemented.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1959
Change-Id: I3e770fd1feb2ddf92cf405a9aa17be92eb32e19b
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added I2C bus (TWIHS) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1866
Change-Id: Ic5aa7b6b21295feccae883d580b38bbeaf2ce291
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add plumbing to build system and SoC level dtsi for the NRF52832 SoC.
We additionally add the necessary yaml files for the UART on the NRF52
SoCs.
Change-Id: I3b4a821b2993827e33d8e84bdbbc759d1521f8bd
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce SoC specific config options similar to what exists on NRF51,
this is mostly to help distinguish between SRAM & Flash sizes on
different variants.
Also deleted some unnecessary setting of CONFIG_SOC_NRF528{32,40} in the
board defconfig files.
Change-Id: I3aaedf0c15423ae12636f87b8e6a39070cbb2c6f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds initial support for the kw40z SoC. This SoC has all the same
peripherals as the kw41z but with less flash and ram, so the defconfig
and dts are nearly the same.
Jira: ZEP-1388
Change-Id: Ib804451e8c2c71c4ff7d342bf23f6567d1542a2d
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The KL2x support requires DTS so we can remove any !HAS_DTS references.
Also NUM_IRQS shouldn't have been in a !HAS_DTS ifdef block.
Change-Id: I12b0781b6eef100bfb0a94698d12fc519c759888
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since all STM32 SoCs are using device tree we can remove this last bit
of !HAS_DTS for getting flash/sram sizes from Kconfig.
Change-Id: I9e706b7aba7c0edcf9fca3ddc0ddc7d820980b47
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Converted over all STM32F3 based boards to use device tree and removed
associated bits that now come from the device tree for STM32F3.
Boards that are now using devicetree:
* Nucleo f334r8
* STM32373C Eval
Change-Id: I081a1d83f86e417a98b6864c745354b6b32953b7
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Converted over all STM32F1 based boards to use device tree and removed
associated bits that now come from the device tree for STM32F1. Also
renamed the STM32F10{3,7} SoC dtsi to try and make it clear that the 'X'
is a place holder. Fixedup the top level compatiables in the boards to
be the specific 'X' instead of the generic one.
Boards that are now using devicetree:
* Nucleo f103rb
* STM3210C Eval
* STM32 MINI A15
Change-Id: I29b3634ec7451f974687d55980414efa655e2e96
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Converted over all STM32F4 based boards to use device tree and removed
associated bits that now come from the device tree for STM32F4.
Boards that are now using devicetree:
* 96b_carbon
* nucleo f401re
* nucleo f411re
Change-Id: Ibe197ca0a3f5ad78d594485a578d986403cc824a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since all the L4 SoCs are using DTS we can remove the various Kconfig
bits that we now get from DTS.
Change-Id: Icdec49b478ff285dc3347b09412964a721f75bbf
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In order to suppport the FRDM-KL25Z board,
it is necessary to make this soc available.
Change-Id: Id93a51dcc9ef58118e27db02c30f662eb73d5adb
Signed-off-by: Gustavo Denardin <gustavo.denardin@gmail.com>
I2C_SHARED_IRQ, I2C_0_IRQ_SHARED, I2C_0_IRQ_DIRECT Kconfig options
are DW driver specific. Its presence is confusing for a user of any
other I2C driver than DW. This patch renames these options to include
DW string and makes it visible only for DW I2C driver. This is a
similar implementation to that used by ETH DW Ethernet driver.
Change-Id: I795506f9b103c028a22317df9ad632dce5cd1343
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Instead of FLASH_LOAD_OFFSET being something specific to cortex-m, add
it generally to misc/Kconfig, along with a hidden config
HAS_LOAD_OFFSET which can be selected by the architectures as they add
support for the functionality.
Change-Id: I256ff8cf4e9b8493b26354c3b93fe1f7017d4887
Signed-off-by: David Brown <david.brown@linaro.org>
gcc only understands -mlongcalls form of this option, xcc understands
both. Use -mlongcalls for building with both xcc and gcc.
Change-Id: I93f65ccbc97429ae564f1986120b37ce205ee38c
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
The issue was that cpStack was changed to a memory buffer by commit
https://gerrit.zephyrproject.org/r/#/c/12816
However the assembly code was expecting it to be a pointer and thus
issuing an indirection, that leads to wrong addresses.
The fix removed this unnecessary indirection and thus the inherent
invalid memory access exception.
Issue: ZEP-1997
Change-Id: I843f049212f2d116a01b05367a284209f463a5e7
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
* CONFIG_SOC is now properly set and we do not need a separate
XTENSA_CORE build variable
* Some unnecessary macro -D CFLAGS in the Xtensa Makefile removed
* There is no default SOC selection, it is now done explicitly in
the board's defconfig
* CONFIG_<board name> now renamed to CONFIG_SOC_<board name in
uppercase> to conform to established style.
Issue: ZEP-1711
Change-Id: I88997530db09970b7fdd1c3e3d355bfca9d0be1a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
_power_save_idle_exit() was removed long ago. All arches now just
call _sys_power_save_idle_exit() if PM is enabled.
Change-Id: I9cce3eecc8cbf1cbce15a355be420e747fb978de
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
When running with qemu often times the developer want to enable all
sorts of debugs which end up not working with only 192K.
Change-Id: I8d784618b9a0d911944f831a4058b34abc0c3e35
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
CONFIG_* usually come from Kconfig, rename variables that are locally
defined to avoid confusion about where they are set.
Change-Id: I402713e6f852907e75be4bc2b916a7d15dd5649c
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
CONFIG_* usually come from Kconfig, rename variables that are locally
defined to avoid confusion about where they are set.
Change-Id: I83b8459913c5deb68dc1b9f5386b8934363a6d1f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The CP context area was before on the bottom of the stack just
after the thread descriptor. Now it is moved inside the thread
descriptor to support some kind of memory protection.
Change-Id: Id3ebeaecfd9c2475899713fdc8da583a1f9121f9
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
I2C_CLOCK_SPEED Kconfig option is DW driver specific. It does not
define I2C interface speed but rather the I2C DW module clock speed.
It is confusing for a user of any other I2C driver than DW.
This patch renames this option to I2C_DW_CLOCK_SPEED and makes it
visible only for DW I2C driver.
Change-Id: I97f57332fd5cca644eabdef0968a0b2174b885ff
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This is only built in if CONFIG_EXCEPTION_DEBUG is turned on.
Change-Id: I91f0601e344919f3481f7f5e78cb98c6784d1ec8
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
same70/soc.h provided IRQ ids as #define. This is no longer
necessary as gen_isr_tables mechanism, which was recently
introduced, supports IRQ ids as enums. These are provided
directly by Atmel ASF library.
Change-Id: I3c2573d97d81eb9a02e85fde0566622ff2ecf2cf
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
These are fixed I/O registers for getting and setting the states of
LEDs, buttons, SPI chip-selects, and LCD control lines. It also contains
several free-running counters with no specific use.
Change-Id: Ib49306d5501574f7eb354165cdca6f29e3d4dad4
Signed-off-by: Jon Medhurst <tixy@linaro.org>
For the SoCs in which all the boards for that platform are using dts we
can remove the Kconfig bits that are now coming from device tree.
Change-Id: Iccf4c84beb83fa1c516b6166f94de37b4a0162ae
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As part of the transition to Device Tree, a temporary
HAS_DTS configuration variable, and a .fixup file per board
with symbol aliases were added.
This patch removes the cc32xx related fixup file
definitions, except for those used additionally outside
the cc32xx drivers.
Since cc32xx has DTS files, and since HAS_DTS will always be true,
it also removes the 'if !HAS_DTS' blocks from the cc32xx Kconfig
files.
Change-Id: I1c1b9f734795f523342f82ab32f2a38983812c0b
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move back to getting the number of IRQs from Kconfig. We do this
because the number of IRQs should really just be determined by scanning
the device tree and figuring out the highest IRQ value used.
Change-Id: I8e0dbec1d9d036d4e899b237c4dc7d833c422e18
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
fibers/tasks are now just threads and we should not be using
struct *tcs any more.
Change-Id: Iee5369abcc66b4357a0c75537025fe8edb0ffbb4
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The SiFive Freedom E310 SOC follows the riscv privilege
architecture specification and hence is declared within
the riscv privilege SOC family.
It also provides support for a riscv
Platform Level Interrupt Controller (PLIC)
Change-Id: I19ff0997eacc248f48444fc96566a105c6c02663
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
This patch updates the ARM core to use struct k_thread instead of struct
tcs. Struct tcs has been deprecated with Zephyr 1.6.
Change-Id: I1219add0bbcca4b963ffe02cd4519eca355c7719
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The Cortex-M4 of the STM32F4 family has an FPU. Enable the FPU support
by selecting CPU_HAS_FPU.
Change-Id: Iddae9c547df6e010562649eb0997dc61563c8fc4
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The comment refers to STM32F1 instead of STM32F4.
Change-Id: Ide116b712146f87a6f4d2aaafea8bd181c4d9397
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The current implementation of stm32_gpio_set() uses the GPIO output data
register to change the state of individual GPIOs. The generated
assembler needs at least 3 instructions: load / modify / store.
This opens a small race window, for example if a thread and an
interrupt both try to change the state of the same GPIO bank.
Use the GPIO bit set/reset register to perform the atomic change without
locking.
This also has the benefit of a more optimised implementation, which can
be useful for GPIO-intensive work. Compare the new version:
08000c98 <stm32_gpio_set>:
8000c98: f001 010f and.w r1, r1, #15
8000c9c: 2301 movs r3, #1
8000c9e: b902 cbnz r2, 8000ca2 <stm32_gpio_set+0xa>
8000ca0: 3110 adds r1, #16
8000ca2: 408b lsls r3, r1
8000ca4: 6183 str r3, [r0, #24]
8000ca6: 2000 movs r0, #0
8000ca8: 4770 bx lr
and the old one:
08000c98 <stm32_gpio_set>:
8000c98: 2301 movs r3, #1
8000c9a: f001 010f and.w r1, r1, #15
8000c9e: fa03 f101 lsl.w r1, r3, r1
8000ca2: 6943 ldr r3, [r0, #20]
8000ca4: b10a cbz r2, 8000caa <stm32_gpio_set+0x12>
8000ca6: 4319 orrs r1, r3
8000ca8: e001 b.n 8000cae <stm32_gpio_set+0x16>
8000caa: ea23 0101 bic.w r1, r3, r1
8000cae: 6141 str r1, [r0, #20]
8000cb0: 2000 movs r0, #0
8000cb2: 4770 bx lr
Change-Id: Ie5800d1c345016028d1b9a099f5d74cac35f592a
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
In prep for supporting the older KL2x SoCs that use a different SPI
block, rename the current SPI driver to DSPI to match what the MCUX HAL
defines it as.
Change-Id: I9097580df5fca649ab6fd9a38212fced0b1ea6ed
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds the necessary changes to enable use of DTS for
generating required build information.
Change-Id: I0d7aa15488339a425ffe57b6354992851212f7f3
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The previous file contained erroneous values of the number of IRQs
in these socs.
Change-Id: Ie7d2c19d86e247599f4924b95d9330175140d894
Signed-off-by: Gustavo Denardin <gustavo.denardin@gmail.com>
The current nordic hal layer in ext/ requires additional macros to
include the correct files. This will be corrected in an upcoming version
of the hal layer itself but for now add the required macros so that
users can benefit from the hal peripheral code.
Change-Id: I95127d0a98d7e882fdc779f961718fa223d504eb
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Updated the riscv-privilege SOC family to account for SOCs supporting
a Platform-level Interrupt Controller (PLIC) as specified by the
riscv privilege architecture.
riscv-privilege SOCs supporting a PLIC have to implement the following
list of APIs:
void riscv_plic_irq_enable(uint32_t irq);
void riscv_plic_irq_disable(uint32_t irq);
int riscv_plic_irq_is_enabled(uint32_t irq);
void riscv_plic_set_priority(uint32_t irq, uint32_t priority);
int riscv_plic_get_irq(void);
Change-Id: I0228574967348d572afc98a79257c697efc4309e
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
added the riscv-privilege SOC_FAMILY, under which all
riscv SOCs supporting the riscv privilege architecture
specifcation shall reside. These SOCs shall notably have
a common base for handling IRQs.
Moved riscv32-qemu under the riscv-privilege SOC_FAMILY
Change-Id: I5372cb38e3eaed78886f22b212ab4f881ef30b3f
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
This directory now handles all of Cortex-M0, Cortex-M3/M4. So, just
consistently use "Cortex-M" (as used by number of files already)
without refering to a particular subarch. Also, consistently (letter
casing) spell it as "Cortex-M". A typo is fixed too.
Change-Id: I42ee09abc9a503381bca4ae437c83a8f48816ebc
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
In Atmel SAM Family of MCUs, the watchdog is enabled by default at boot.
The watchdog once disabled, cannot be re-enabled back without a reset.
Hence disabling the Watchdog needs to be handled via the Watchdog driver.
Tested on Atmel SAMV71 Xplained Ultra Evaluation Kit.
Jira: ZEP-1684
Change-Id: I5682c3f007a846b064b8d16abf0d9b67d4c8e7d6
Signed-off-by: Souvik K Chakravarty <souvik.k.chakravarty@intel.com>
Enable UART_QMSI_0 whenever NBLE is enabled the same way as it is done
for BLUETOOTH_H4.
Change-Id: Ib2f76f7e5e95620d40320891fec1b86509d1856e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Help text in Kconfig files should be indented with <tab><space><space>.
Change-Id: Iefa5c8f4bfe329b4ee754ebfe43766f445432184
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Provide a random driver wrapped around the MCUX TRNG driver.
Change-Id: Icbd7ab587aa18ecbd7eae52290aaa5d8ee504cf2
Origin: Original
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
MCUX contains more than one type of random number generator,
so refrect this in config and file names.
Change-Id: Iba4482a1ae41f35d471686f8b159c113147c4df8
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Fix c6e27a05 was too aggressive. It turns out that bluetooth on the
Quark SE boards won't enable it's own UART, because it had always been
enabled. Apps that don't do it already will be broken.
Enable UART_QMSI_0 whenever BLUETOOTH_H4 is pulled in on this
platform.
Change-Id: I5e21c6004714adba8fb0fafa056dc2d62698a3d1
Issue: ZEP-1788
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Cube HAL implements timeout based on 1ms tick.
This commit allows Cube HAL to get Zephyr system clock.
Change-Id: I9a59edcf6fa8e0ebfd5040348db537dadd9fcdfa
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to support the discovery STM32F4 and STM32F429 boards,
it is necessary to make these socs available.
Change-Id: I351d294fb02c4385f291a6e258a3f7d81e85627e
Signed-off-by: Gustavo Denardin <gustavo.denardin@gmail.com>
Currently, ARM Cortex-M image ROMs are linked starting at the flash
device's base address (CONFIG_FLASH_BASE_ADDRESS). This prevents XIP
Zephyr applications from being linked to run from elsewhere on the
flash device. Linking Zephyr applications to run from elsewhere can be
necessary when running under a bootloader (i.e., booting into a Zephyr
application from a bootloader, not using Zephyr as a bootloader).
To enable this use case, add a new config option: FLASH_LOAD_OFFSET.
This option directs the linker to treat ROM as if it started that many
bytes from the base of flash on Cortex-M targets. The option defaults
to zero to preserve backwards compatibility.
Change-Id: I64f82aee257c19c2451f9789b0ab56999775b761
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
The defconfigs would always create a device for UART 0, which is
problematic in circumstances where both the x86 and ARC cores are
alive and one wants to use it in a non-default configuration.
Specifically: on Arduino 101 this is the bluetooth device and it
operates at 1MBps instead of of 115200kbps. If an x86 app sets this
up correctly, but then starts the ARC core running an app which
doesn't reference this UART at all, the device will still exist and
set up the (wrong!) configuration, clobbering the correct settings.
Just remove the "def-bool y" bits from the defconfig. There's no
need, users of these devices (e.g. the console) will enable them
anyway. There's no value to compiling it in without a configured
user.
Issue: ZEP-1677
Change-Id: I4a0e944f23705495433e9f3d0459065f131579cb
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Some files made it through review process with full license header.
Change-Id: I2722b127c40b4b19500042c12e4fde85a165bae9
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Currently, if IRQ number != RISCV_MACHINE_TIMER_IRQ (only device IRQ in qemu),
riscv32-qemu was considering the IRQ as an exception. However, fake IRQs
can also be generated by setting corresponding bits in the Machine Interrupt
Pending register (mip). With the current implementation, these IRQs were
considered as unexpected exceptions.
To circumvent the problem, update the IRQ filtering mechanism by considering
an IRQ (IRQ number as reported by the mcause register) as an exception only
if its corresponding bit is NOT set in the mip register.
Change-Id: I4c581a84d83ee0ba2c4ea35f89ba732401eb8fa4
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
This implementation of _tsc_read returns a 64-bit value that
is derived from the 64-bit tick count multiplied by hwcycles per tick,
and then it adds the current value from the 32-bit timer.
This produces a 64-bit time. There is a bunch of math here, which
could be avoided if the CPU is built with Real-Time-Clock option.
EM Starter Kit SOCs don't have this. I don't think Arduino 101 does
either.
See ZEP-1559
Change-Id: I9f846d170246556ac40fe2f45809e457c6375d8c
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
The interrupts would be placed at incorrect offsets on systems where
some interrupt vectors are reserved for exceptions, such as ARC.
Change-Id: I5b1f00eb9e8aecb84ae66e3d0461a734ffb5fbe6
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
If this is set incorrectly things will break all over the place.
Needs a default defined per-arch and left alone.
Change-Id: I3f8c842937a240297ee21589a22a7a9e51dbdfad
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The wrong UART was set on for the qemu_cortex_m3 slip (uart pipe) device
Change-Id: If6d6af0f32ef02ccc559cd1fff90ea499cc378c4
Signed-off-by: Richard Peters <mail@richardpeters.de>
Added a riscv-privilege.h header file that contains common
definitions for all riscv SOCs supporting the riscv
privileged architecture specification.
This shall ease addition of future riscv SOCs supporting
the riscv privileged architecture spec.
Change-Id: I5714bf70eeda738a25967ed26d3d0d2aaa0c9989
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
When an IRQ is serviced, the ISR dispatcher will check for any new thread in
the ready queue and switch to it. However, if the current thread is marked as
non preemptable due to _kernel.current->base.preempt > _NON_PREEMPT_THRESHOLD
then we should not switch to another one.
Change-Id: Icdc08105cc6433da479bb95265710462a0f37c0b
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
This core is not depreciated and compilationfor it is even faster than D_233L.
Change-Id: I6b8149ca9e879770c3ed0973ffb9304e2e3c8d8d
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
1) Fatal errors now all go through _SysFatalErrorHandler. When the
simulator is used, only the death of 'essential' threads will result
in the simulator exiting; some test cases that test exceptions may
actually expect a thread to terminate abnormally.
2) The human readability of the exception errors is improved.
Change-Id: I77f57ea0eae15b0c55237681b959cd21e3fe8c1c
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The a3 register was supposed to hold the _thread pointer but it seems that it
does not in all cases. Safe to restore it from _kernel structure.
Change-Id: Ie2ff6c3faf0fe70de4c5877ab59433d0c165145b
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
This change should allow threads that do not access coprocessor to safely
overflow on the coprocessor save area without any issue.
Change-Id: Ic2acd20b60b6bef0b7feeb8cfb54d548eba892f0
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
This was a kind of optimization that save few cycles in the cost of code
duplication. However the path where we resume from interrupt withouch changing
the running thread is buggy and leads to many tests to fail. For now I'd prefer
to remove this optimization and have a working port. Later, once everything is
OK, I'll have time to optimize things.
Change-Id: I7af58f383848d157b9f3b3fbeceede3e83f9ce61
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
Having duplicate code leads always to this kind of situation where a bug is
fixed in one place and not in the other. This bug of updating current thread
pointer was already fixed before in the Swap function, but not in the interrupt
handler.
Change-Id: I466aea2d35382446c5c82fe775ada31f0bd19492
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
Some options which are already defined by the build system
for the C compiler or assembler have been removed: -c,
-xassembler-with-cpp, -nostdinc.
References to deleted variable flagALongCall and flagLongCall
removed.
Formatting for 80 columns, there is now one flag per line.
Change-Id: Ieecdb75e26f64c6f58dec3cc636552e7b31a678d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The retval field shall hold the return value itself not a pointer on its
location.
Change-Id: I3f9e225f2bdd501f88441946b5187ebbd17a71e3
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
This was introduced during a copy/paste when updating patch
https://gerrit.zephyrproject.org/r/#/c/10323/6..7
Change-Id: Id6857dd28a16974361932285b44559f702c4d910
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
This function needs to be decalred in a file included by _thread_entry.
It also needs to have exit function declared as not returning.
Change-Id: I2a01e7408cf70266351ae5089f45b5d9d009fabe
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
The function _new_thread sets the CALLINC for _thread_entry when calling the
new thread entry point. This should be CALLINC(1) (call4) instead of previous
one CALLINC(2) (call8).
This change allows resolving a crash when starting the first thread.
Change-Id: Ie97c95c87d1219342fed09f670fcae8a6230cefe
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
These libraries are unlikely to be uesd by GCC port and thus should not be in
a generic make file. Moved to specific toolchain make file.
Change-Id: Ib585b87700e409d678f7a5cb60cff67b6022ab05
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
Master branch changed requirements for license headers while this
branch has been in development.
Change-Id: I9bce16ff275057a4bb664019628fc9b6de7aef7c
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Provide generic support for running zephyr kernels on xtensa QEMU and
map D_233L SoC to dc233c QEMU core.
Change-Id: Ie804588f750213a7cc54dbc95c86ee4d62ba1ea5
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Added arch sub folder, make files and Kconfig files for a set of standard SoCs.
Change-Id: I4ee9cba966860072e55c95795d87356b665e4d49
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
This replaces the hard-coded vector table, as well as the
software ISR table created by the linker. Now both are generated
in build via script.
Issue: ZEP-1038, ZEP-1165
Change-Id: Ie6faaf8f7ea3a7a25ecb542f6cf7740836ad7da3
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This is a new mechanism for generating interrupt tables which will
be useful on many architectures. It replaces the old linker-based
mechanism for creating these tables and has a couple advantages:
1) It is now possible to use enums as the IRQ line argument to
IRQ_CONNECT(), which should ease CMSIS integration.
2) The vector table itself is now generated, which lets us place
interrupts directly into the vector table without having to
hard-code them. This is a feature we have long enjoyed on x86
and will enable 'direct' interrupts.
3) More code is common, requiring less arch-specific code to
support.
This patch introduces the common code for this mechanism. Follow-up
patches will enable it on various arches.
Issue: ZEP-1038, ZEP-1165
Change-Id: I9acd6e0de8b438fa9293f2e00563628f7510168a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In order to set breakpoints after waking up from sleep,
it is needed to save DR0/DR1/DR2/DR3 and DR6/DR7.
As DR4/DR5 are reserved or mapped to DR6/DR7, they are not saved.
Patch2 : Added compile time checks for debug build or soc_watch
build for Intel Energy analysis.
Patch3 : Avoid clobbering of edx.
JIRA: ZEP-1681
Change-Id: I62fbedca16953d57196420ecae4fb93c785bb4a5
Signed-off-by: Sarath R Nair <sarath.nandu.ramachandran.nair@intel.com>
This patch moves the include for the generated_dts_board.h inside of
the include/arch/arm/arch.h file. This was done to simplify the
includes required for files. Only two files will include the dts
generated include file directly: arch.h and the linker.ld
Change-Id: I2614f4fd4eeed2ab635a3264d7dac8b83f97b760
Signed-off-by: Andy Gross <andy.gross@linaro.org>
We now use CMSIS for ARM Cortex-M SoCs so we can remove the last bits of
scs and scb.
Jira: ZEP-1568
Change-Id: I0c7c45b0321dc402ed594e9faffb5109922edcf0
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Coverted:
_ScbMemFaultMmfarReset
_ScbBusFaultBfarReset
_ScbUsageFaultAllFaultsReset
To use direct CMSIS register access.
Also removed scb.h and references as there is no longer any code in it.
Jira: ZEP-1568
Change-Id: I469f6af39d1bd41db712454b0b3e5ab331979033
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The previous code incorrectly used the value 0xfe to clear the mem and
bus faults. It attempted to handle the address register valid bits
separately, but reversed the bit order.
Jira: ZEP-1568
Change-Id: I240d072610af9979ca93c0081ed862df08929372
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converted access to CFSR MMFSR, BFSR, and UFSR to use direct CMSIS
register access when printing out the values of those registers.
Jira: ZEP-1568
Change-Id: I7969bb81346327637140ec23d91422a6bfaef032
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Coverted:
_ScbBusFaultAddrGet
_ScbMemFaultAddrGet
To use direct CMSIS register access
Jira: ZEP-1568
Change-Id: Ic49b3ac3fc4fb63d413f273569c77f6539e4e572
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Pin number should be decremented by 8 if the pin
refers to the GPIOx_AFRH register.
Change-Id: I76e960f3b4adc3c2139ef5a88f15dbe98603228e
Signed-off-by: Adam Podogrocki <adam.podogrocki@rndity.com>
Following activation of Cube LL based clock control driver,
this commits cleans up the useless structures for RCC definitions
and remove code relative to native F3 Clock control driver.
Change-Id: I6f3ee44adb09adc52927eb4b05f8a829665eb96d
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following activation of Cube LL based clock control driver,
this commits cleans up the useless structures for RCC definitions
and remove code relative to native L4 Clock control driver.
Change-Id: Ic0408d5f5ec66651d46d13dfaf447da2666367cd
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introduction of STM32Cube based clock control driver for
stm32 family, provide its support on stm32f3x soc.
Clean up will have to be done afterwards.
Change-Id: I20480579f12a6fc1f1f6a51589981ac3f1d63ef0
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introduction of STM32Cube based clock control driver for
stm32 family, provide its support on stm32l4x soc.
Clean up will have to be done afterwards.
Change-Id: I979a4169148c5fe5a0693d182d2d17f9ffaf1c77
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds the base DTS support for the KW41Z Freedom board. The
initial set of changes include SRAM, FLASH, IRQ controller and LPUART
support.
Change-Id: Ic68c4959ddad0c5cfe70d5576a0e58372b93ec9d
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
This patch adds DTS support to the ARM CMSDK UART driver. The DTS
currently specifies the IRQ, IRQ PRIO, and base address of the port.
Change-Id: I8e5bc81c013958be4297d563495bf126b53a83a9
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the base DTS support for the V2M Beetle board. The
initial set of changes include SRAM, FLASH, and IRQ controller support.
Change-Id: I06685622b9c57ac358544c71350074ce06e3371e
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds all the necessary changes to enable use of DTS for
generating required build information.
Change-Id: Ia476fbb14c7d9d6b9db3340c73f599556a880da3
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch ifdef's out information that would be redefined by
information generated from DTS. This patch also fixes up the serial
drives to work properly with the DTS generated information.
Change-Id: I912ccf35be23c107705a4866e5a68b3b51154ffa
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds DTS support and related files for the NXP Kinetis
platform. The DTS files contain the base definitions for the hardware
nodes on Kinetis platforms. The YAML files provide the definitions of
the contents of the DTS nodes.
The Kconfig changes were put in place to allow for the conversion of
existing drivers. Once those drivers are modified, the Kconfig options
that are replaced by the DTS information will be removed.
Change-Id: If110fffa99c0b12471cf2df206da6687277e4756
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support for using device tree configuration files for
configuring ARM platforms.
In this patch, only the FLASH_SIZE, SRAM_SIZE, NUM_IRQS, and
NUM_IRQ_PRIO_BITS were removed from the Kconfig options. A minimal set
of options were removed so that it would be easier to work through the
plumbing of the build system.
It should be noted that the host system must provide access to the
device tree compiler (DTC). The DTC can usually be installed on host
systems through distribution packages or by downloading and compiling
from https://git.kernel.org/pub/scm/utils/dtc/dtc.git
This patch also requires the Python yaml package.
This change implements parts of each of the following Jira:
ZEP-1304
ZEP-1305
ZEP-1306
ZEP-1307
ZEP-1589
Change-Id: If1403801e19d9d85031401b55308935dadf8c9d8
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Without this patch, the final linker script had a memory region defined
as:
RAM (wx) : ORIGIN = 0xA8006400, LENGTH = 55*1K - 0x20 +0x4
resulting on the wrong RAM length. Fix BSP_SHARED_RAM_SIZE definition
so the sum is always processed first.
Change-Id: I16b93adbaf27bb84b6e5d1ac433ef80f854b218c
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Arch-specific stuff shouldn't be in the toplevel Makefile,
forthcoming patches will soon introduce special interrupt
handling logic for other arches.
Change-Id: Ib5a86cbdf5b32ecfce9e5e234f7cbea2bc3ce9c1
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This private data structure now no longer introduces a typedef or
uses CamelCase. It's not necessary to specify the size of extern
arrays, so we don't need a block of #ifdefs for every arch.
Change-Id: I71fe61822ecef29820280a43d5ac2822a61f7082
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This commit removes the local implementation of enter_arc_state, where
the ARC is instructed to sleep, using instead the QMSI 1.4 functions.
Change-Id: Id489ad53851be50fc5e50add698891fcfaef3abe
Signed-off-by: Juan Solano <juanx.solano.menacho@intel.com>
This flag is no longer necessary and TICKLESS_IDLE will be
enabled by default if SYS_POWER_MANAGEMENT is enabled.
Jira: ZEP-1325
Change-Id: Ic6cd4b8dc0a17c6a413cabf6509b215a4558318d
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
A new shared memory area has been added to the QMSI bootloader in
order to store the GDT in RAM reliably.
Add the new entry to the QUARK D2000 linker script and new
kconfig options:
* CONFIG_BSP_SHARED_GDT_RAM_ADDR to set the address location
of the GDT in RAM.
* CONFIG_BSP_SHARED_GDT_RAM_SIZE to set the size used by the
GDT in RAM.
This is only enabled when CONFIG_SET_GDT is NOT set.
Change-Id: Ie084079475853dce153dd9f3e88ad4a9784bdedf
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
A new shared memory has been added to the QMSI bootloader in order to
store the GDT in RAM reliably.
Add this new entry to the QUARK SE C1000 linker script and new kconfig
options:
* CONFIG_BSP_SHARED_GDT_RAM_ADDR to set the address location
of the GDT in RAM.
* CONFIG_BSP_SHARED_GDT_RAM_SIZE to set the size used by the
GDT in RAM.
Additionally, both BSP_SHARED_RAM_ADDR and BSP_SHARED_RAM_SIZE have been
renamed to BSP_SHARED_RESTORE_INFO_RAM_ADDR and
BSP_SHARED_RESTORE_INFO_SIZE respectively, in order to better resemble
what these options are for. All these configs are available
unconditionally.
Change-Id: I07ee8b440d4a3f5e9bdeb62441ff6a7bd6d4c153
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Bartlomiej Majka <bartlomiejx.majka@intel.com>
For the next QMSI release, the shared restore info address has been
modified to 0xA8013FDC .
Change-Id: I72eaef4f15f7ef6fb8e7eb9acd7d96451623e103
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Update the builtin QMSI code to 1.4 (RC2).
The below shim drivers were updated for API or interface changes:
- aio
- counter
- i2c_ss
- rtc
- wdt.
Also, arch soc specific power management code were updated.
Jira: ZEP-1572
Change-Id: Ibc8fae032a39ffb2c2c997f697835bc0208fd308
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
The entry point specified in the elf file should always point to
executable code, and not to the interrupt vector table. Pointing to the
vector table as the entry point in the elf file presents problems with
running the kernel against a debugger as the debugger starts the program
counter at the top of the interrupt vector table.
Change-Id: I76051f6e99a44bab72936670bead5fb8191a6ec7
Signed-off-by: Tim Nordell <tim.nordell@nimbelink.com>
Rename devices. For example, the two i2c devices in the
quark se sensor sub-system will have name string "I2C_0"
and "I2C_1", while the other two i2c devices accessible to
both x86 and arc will have name string "I2C_2" and "I2C_3".
This is valid only when you build arc binary.
It does not apply if you build x86 or arm binary. Similar change is
also made for GPIO and SPI.
Jira: ZEP-1588 ZEP-1614
Change-Id: Ibad4486e70e0aaf287763514a5a9d28b43bca094
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Added a linker script that shall be common to most riscv SOCs.
Linker script also accounts for execution in place in ROM, when
CONFIG_XIP is set.
Nonetheless, riscv32 SOCs (like pulpino) requiring a different
system layout can still define their own linker script.
Change-Id: I3ad670446d439772c29a8204e307ac79643dc650
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
riscv defines the machine-mode timer registers that are implemented
by the all riscv SOCs that follow the riscv privileged architecture
specification.
The timer registers implemented in riscv-qemu follow this specification.
To account for future riscv SOCs, reimplement the riscv_qemu_driver by
the riscv_machine_driver.
Change-Id: I645b03c91b4e07d0f2609908decc27ba9b8240d4
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
This is a zero-copy networking implementation of Ethernet driver.
Limitations:
- one shot PHY setup, no support for PHY disconnect/reconnect
- no support for devices with DCache enabled due to missing
non-cacheable RAM regions in Zephyr.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1492
Change-Id: Ib944f91193efbd12c1142b0bcf1f635388bf1b87
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added basic USART driver for Atmel SAM MCU family. USART is a very
comprehensive module, currently only basic features sufficient to
support printf functionality are implemented by this driver.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Ia9710e4069243fb6c30de45953dfc1fe1266b63a
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
Added common, internal, always available SAM HAL drivers: pmc, gpio.
Note: these drivers are meant to be used by other SAM drivers, not by
a user space program directly.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: I00cca358f27790dc94cf79f840584b85ff5191f6
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
Added support for early SoC configuration which does not belong
conceptually to system initialization. ERASE, JTAG TDI pins are
currently configured here.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Id51adddb4c7cce22907af214461d75db83df129a
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added support for Atmel SAM E70 (Cortex-M7) MCU:
- Kconfig files
- device start-up code
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Ide4fd5dadd94897303090a6507b8d048773b645e
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
As cpu_idle.S is the only bit of code that is using the SCB asm defines,
so to allow us to remove scb.h in the future lets move the defines that
are used just into cpu_idle.S
Jira: ZEP-1568
Change-Id: I3c3a6f145ec4c1a43f076d079d5fe1694c255b78
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A number of SoCs clear out the Mem/Bus/Usage and Hard Fault exceptions
during init. Lets refactor that into a common function so we don't have
to keep duplicating it over and over.
Change-Id: Ida908a9092db37447abcf3c9872f36937982f729
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch fixes the UART4 base address on the ARM MPS2 platform.
Change-Id: I14bf2a4dc2378d4b2c4295a75cd68c6c895fbd60
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Kill of nvic.h and use either CMSIS helper functions for NVIC or direct
NVIC register access via CMSIS for IRQ handling code.
Jira: ZEP-1568
Change-Id: If21910b9293121efe85c3c9076a1c2b475ef91ef
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace _ScbExcPrioSet with calls to NVIC_SetPriority as it handles both
interrupt and exception priorities. We don't need to shift around the
priority values for NVIC_SetPriority.
Jira: ZEP-1568
Change-Id: Iccd68733c3f7faa82b7ccb17200eef328090b6da
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds the configuration parametes required to enable CMSDK
(Cortex-M System Design Kit) Drivers at MPS2 soc level.
It provides as well the definitions for the MPS2 System Control
registers.
Change-Id: I06181dcfeb4fb887425b85ec9a99c268c857a34e
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Adds initial support for the kw41z SoC. This is the first SoC in the
Kinetis W (wireless connectivity) series added to Zephyr. The kw41z
integrates a 2.4 GHz radio transceiver, BLE link layer hardware, and an
802.15.4 packet processor with an ARM Cortex M0+. It has 512 KB flash,
128 KB SRAM, and can run the system clock at up to 48 MHz.
This SoC currently has mcux shim drivers for lpuart (serial), gpio,
pinmux, i2c, and flash.
Jira: ZEP-1389
Change-Id: I8cff6d203867ba3ace7e05c36441dc8f3cbca8d8
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Renames the flash security section so it makes sense for other Kinetis
devices, not just k64. In Kinetis reference manuals, this section is
referred to as the 'flash configuration field'.
Change-Id: I2b7c7cc1ec2541419d77878d367d96c9ceb7a0cf
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux lpuart driver to adapt it to the Zephyr
serial interface.
NXP has multiple uart hardware blocks that implement different features
and have different register maps. The k64 has a uart block called
'uart', while the kw41 has a uart block called 'lpuart' (low power
uart). The MCUXpresso SDK provides separate drivers for each type of
uart block but with similar software interfaces. As a result, there are
also separate shim drivers in Zephyr. There is a 1:1:1 relationship
between hardware block, mcux driver, and mcux shim driver.
Because we now have two mcux shim drivers for the uart interface, a new
naming convention is created:
<interface>_mcux_<hw block>
Where <interface> is the name of the Zephyr interface, in this case
'uart'. This convention is not new.
<hw block> is the name of the NXP hardware block, in this case 'lpuart'.
This is the new part, and distinguishes different hardware blocks
for the same interface.
Change-Id: I3a80b9bffa116bbb2b02ee950d4bdd79a19a4edc
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Nordic Semiconductor's Software Development Kit's HAL layer
provides a set of low-level header and sourcefiles that give access
to the different hardware peripherals of Nordic ICs.
This patch includes the new files in the build and refactors the Kconfig
and Kbuild files in ext/hal/nordic to acommodate for the presence of the
new HAL layer.
Change-Id: Ie8e1a4c9fcc7e9058a9d16a2692ef1789603aa53
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The STM32 GPIO driver extended the generic GPIO driver interace with
the concept of OPEN_DRAIN. There is previous discussion about
representing such concepts in the GPIO interface in a more general
fashion here:
https://lists.zephyrproject.org/archives/list/devel@lists.zephyrproject.org/thread/6DCFUAKCOOOBHUO3ZK45ES6IQXOEOFWN/
The DRIVE STRENGTH interface supports the concepts of OPEN DRAIN and
other variants supports by other vendors hardware.
Adjust the STM32 GPIO driver to use the DRIVE STRENGTH interface. A
following patch will address the simplication of gpio.h
Change-Id: I56b0792ec2b21f1adc673dff019288dc8573d005
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
This patch changes Quark SE power drivers to support multicore scenarios
e.g. both LMT and ARC core are enabled and manage power.
Handling LPS states in multicore scenarios are dead simple because LPS
states are core-specific states. It means that putting the LMT core in
LPS doesn't affect the ARC core, and vice-versa. DEEP_SLEEP state, on
the other hand, affects both cores since it turns power off from the SoC
and both cores are shutdown. It means that if LMT puts the system in
DEEP_SLEEP, ARC core is shutdown even if it is busy handling some task.
In order to support the multicore scenario, this patch introduces the
SYS_POWER_STATE_DEEP_SLEEP_2 state to both ARC and x86 power drivers.
On ARC, this state works as following:
1) Save ARC execution context;
2) Raise a flag to inform the x86 core that ARC is ready to enter in
DEEP_SLEEP;
3) Enter in the lowest core-specific power state, which in this case is
LPSS.
On x86, DEEP_SLEEP_2 is very similar to DEEP_SLEEP. The difference relies
in the post_ops() which calls _arc_init() in order to start ARC core so
it can restore its context.
This patch also adds the test/power/multicore/ directory which provides
sample application to x86 and ARC cores in order to easily verify the
multicore support. In test/power/multicore/README.rst you can find more
details regarding the applications.
Jira: ZEP-1103
Change-Id: Ie28ba6d193ea0e58fca69d38f8d3c38ca259a9ef
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This avoids asm files from having to explicitly define the _ASMLANGUAGE
symbol themselves.
Change-Id: I71f5a169f75d7443a58a0365a41c55b20dae3029
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
The K_<thread option> flags/options avaialble to users were hidden in
the kernel private header files: move them to include/kernel.h to
publicize them.
Also, to avoid any future confusion, rename the k_thread.execution_flags
field to user_options.
Change-Id: I65a6fd5e9e78d4ccf783f3304b607a1e6956aeac
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
They are internal states, not user-facing.
Also prepend an underscore since they are kernel internal symbols.
Change-Id: I53740e0d04a796ba1ccc409b5809438cdb189332
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
They are not part of the API, so rename from K_<state> to
_THREAD_<state>.
Change-Id: Iaebb7d3083b80b9769bee5616e0f96ed2abc5c56
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
Replace _scs_relocate_vector_table with direct CMSIS register access and
use of __ISB/__DSB routinues. We also cleanup the code a little bit to
just have one implentation of relocate_vector_table() on ARMv7-M.
Jira: ZEP-1568
Change-Id: I088c30e680a7ba198c1527a5822114b70f10c510
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
CMSIS provides a complete implentation for reboot, we can utilize it
directly and reduce zephyr specific code.
Jira: ZEP-1568
Change-Id: Ia9d1abd5c1e02e724423b94867ea452bc806ef79
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As a first step towards removing the custom ARM Cortex-M Core code
present in Zephyr in benefit of using CMSIS, this change replaces
the use of the custom core code with CMSIS macros in
enable_floating_point().
Jira: ZEP-1568
Change-id: I544a712bf169358c826a3b2acd032c6b30b2801b
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Support using CMSIS defines and functions, we either pull the expect
defines/enum from the SoC HAL layers via <soc.h> for the SoC or we
provide a default set based on __NVIC_PRIO_BITS is defined.
We provide defaults in the case for:
IRQn_Type enum
*_REV define (set to 0)
__MPU_PRESENT define (set to 0 - no MPU)
__NVIC_PRIO_BITS define (set to CONFIG_NUM_IRQ_PRIO_BITS)
__Vendor_SysTickConfig (set to 0 - standard SysTick)
Jira: ZEP-1568
Change-Id: Ibc203de79f4697b14849b69c0e8c5c43677b5c6e
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In preperation for removing the scb/scs layers and using CMSIS directly
lets remove all the _Scb* and _Scs* functions that are not currently
used.
Jira: ZEP-1568
Change-Id: If4641fb9a6de616b4b8793d4678aaaed48e794bc
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
ARM's Cortex-M Prototyping System (or MPS2) [1] is a board containing
devices such as RAM, ethernet and display, and at its heart there is an
FPGA which can be programmed with various 'SoCs' which implement the
CPU, SRAM, UARTs, SPI, DMA, etc. There are also software simulations of
systems based on this hardware which are part of ARM's Fixed Virtual
Platforms (FVPs).
All of the above could be regarded SoCs in the same series so we will
treat them as such in Zephyr.
In this initial patch we add SoC support for the public FPGA image
which implements a Cortex-M3 CPU, and includes definitions to support
use of the UARTs on this.
ARM's documentation for MPS2 images are titled 'Application Note ANnnn'
where the number nnn is different for each 'SoC'. E.g. Application Note
AN385 is for "ARM Cortex-M3 SMM on V2M-MPS2" [2]. The files ARM supply
for programming the board firmware also make extensive use of the ANnnn
nomenclature, so we will use this for the SoC name in Zephyr. E.g. the
Cortex-M3 SoC will be called 'mps2_an385'. Note, it is not possible to
use the CPU type (e.g. M3) for the name as there are multiple FPGA
images for some CPU types (e.g. there are three Cortex M7 images
with differing FPU and MPU support).
[1] https://www.arm.com/products/tools/development-boards/versatile-express/cortex-m-prototyping-system.php
[2] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dai0385c/index.html
Change-Id: Ice54f2d2cde7669582337f256c878526139daedd
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Now that we have a more generic mcux spi driver that can be used across
multiple Kinetis SoCs, remove the specific k64 spi driver.
Jira: ZEP-1374
Change-Id: Ifc324374f305837f5e3d2cfd7ad30d3608865b5b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds the timers IRQ map to the ARM Beetle SoC platform.
Jira: ZEP-1300
Change-Id: If38a197210f71ae90c7ee6274395f064116faf72
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
On other targets, CONFIG_TEXT_SECTION_OFFSET allows the entire image to
be moved in memory to allow space for some type of header. The Mynewt
project bootloader prepends a small header, and this config needs to be
supported for this to work.
The specific alignment requirements of the vector table are chip
specific, and generally will be a power of two larger than the size of
the vector table.
Change-Id: I631a42ff64fb8ab86bd177659f2eac5208527653
Signed-off-by: David Brown <david.brown@linaro.org>
Now that we have a more generic mcux serial driver, remove the uart_k20
driver.
Jira: ZEP-719
Change-Id: I51a3237454140feabbfe18ac2c8ee451e572c7be
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Stop using the specific uart_k20 driver by default and start using the
more generic mcux uart driver instead.
Jira: ZEP-719
Change-Id: I7b107ea7118887591362159283ebb5413b45595a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Implementation includes adding some defines in the pinmux,
adjusting gpio driver to specific defines for STM32F3X family,
adding specific functionality in the F3X SoC definition.
Change-Id: I465c66eb93e7afb43166c4585c852e284b0d6e67
Signed-off-by: Adam Podogrocki <adam.podogrocki@rndity.com>
SOC_FLASH_NRF5 is compatible with any nrf5 device, so enable the driver
by default if CONFIG_FLASH is also enabled.
Change-Id: I6ddf7cc41bb28071f682e78661b184a8e2ee7aa9
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
It is called before early SoC initialization, so remove the duplicated
code from other boards and just set it by default when using XIP.
This can later be used when adding bootloader support, as an
additional option could be created to move the VTOR offset to a
different address.
Change-Id: Ia1f5d9a066de61858ee287215cefdd58596b6b1c
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
pulpino soc has custom-extended riscv ISA that is accounted
for if CONFIG_RISCV_GENERIC_TOOLCHAIN is not set.
(ex: bit manipulation asm opcodes)
Change-Id: I4dafc4ebc2fedcc4eb6a3dedd0412816afea6004
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
RISC-V is an open-source instruction set architecture.
Added support for the 32bit version of RISC-V to Zephyr.
1) exceptions/interrupts/faults are handled at the architecture
level via the __irq_wrapper handler. Context saving/restoring
of registers can be handled at both architecture and SOC levels.
If SOC-specific registers need to be saved, SOC level needs to
provide __soc_save_context and __soc_restore_context functions
that shall be accounted by the architecture level, when
corresponding config variable RISCV_SOC_CONTEXT_SAVE is set.
2) As RISC-V architecture does not provide a clear ISA specification
about interrupt handling, each RISC-V SOC handles it in its own
way. Hence, at the architecture level, the __irq_wrapper handler
expects the following functions to be provided by the SOC level:
__soc_is_irq: to check if the exception is the result of an
interrupt or not.
__soc_handle_irq: handle pending IRQ at SOC level (ex: clear
pending IRQ in SOC-specific IRQ register)
3) Thread/task scheduling, as well as IRQ offloading are handled via
the RISC-V system call ("ecall"), which is also handled via the
__irq_wrapper handler. The _Swap asm function just calls "ecall"
to generate an exception.
4) As there is no conventional way of handling CPU power save in
RISC-V, the default nano_cpu_idle and nano_cpu_atomic_idle
functions just unlock interrupts and return to the caller, without
issuing any CPU power saving instruction. Nonetheless, to allow
SOC-level to implement proper CPU power save, nano_cpu_idle and
nano_cpu_atomic_idle functions are defined as __weak
at the architecture level.
Change-Id: I980a161d0009f3f404ad22b226a6229fbb492389
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
Force-align all variables defined via asm .word to ensure 4-byte
alignment.
The straddled_tick_on_idle_enter variable was a bool, which resolved in
an one-byte quantity. Changing it to a 32-bit integer. It would have
occupied 4 bytes anyway with alignment.
Fixes ZEP-1549.
Change-Id: If5e0aa1a75dbc73d896b44616f059d221fe191c6
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The mcux pinmux driver enables the port clocks, so the soc init no
longer needs to enable them. Also removes some soc defines that were
used only by the legacy k64 pinmux driver.
Change-Id: I63174bef4024b5a09a73f941cea0aec691c759d3
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that we have a more generic mcux gpio driver that can be used across
multiple Kinetis SoCs, remove the specific k64 gpio driver.
Jira: ZEP-1394
Change-Id: I177f96a75e441b70c523e74e99f1b7a54eac6b0e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Stop using the specific k64 gpio driver by default and start using the
more generic mcux gpio driver instead.
Jira: ZEP-1394
Change-Id: I54ec9b62cc8790b8973efc34fa36d17da523971e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moves the uart console pins from the k64 soc init to the frdm_k64f and
hexiwear_k64 board pinmux tables. Not having these pins in the board
pinmux tables led one to believe that no pins in PORTB were being used
on the hexiwear_k64 board, and thus the port was incorrectly disabled by
default.
Also fixes PORTB to be enabled by default if the uart console is used.
Change-Id: Ide6b7b34dfba8a75a02a8f2bf37cce843afb92f1
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch provides initial support for the SoC STM32F107. This SoC
belongs to the Connectivity Line devices.
Connectivity line family incorporates up to 14 communication
interfaces such as: 2 x I2C, 5 x USART, 3 x SPI, 2 x CAN, USB 2.0,
10/100 Ethernet MAC.
Change-Id: I5cb2c458bce9ec1558b4168e87a7003ad9f606a5
Signed-off-by: Adam Podogrocki <adam.podogrocki@rndity.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all the ksdk/mcux shim drivers use the config HAS_MCUX, we can
remove the config HAS_KSDK.
Change-Id: I94b7db41efae10c9234681aeb57f94e67a33c262
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Renames the ksdk random generator shim driver to mcux.
Change-Id: I8bc376937fed3024c809782139a0a72c7332f89a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The ksdk pinmux dev driver was previously merged into the regular ksdk
pinmux driver, and the config PINMUX_DEV_KSDK was removed. Two
references were inadvertantly left behind, so remove them now.
Change-Id: I77394be5459d55a9f16e7bd2b3c9d688c4605b4f
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
stm32f411re SoC could run at system clock above 84MHz.
This was not taken into account in __setup_flash function which configure
flash latency depending on system clock. This is now corrected.
Assert added to ease error detection.
Change-Id: I49b92256d611ef464171fb1d8812a4c4d3c27ab8
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Previously, CC3200 drivers had two options to use the peripheral
driver library APIs:
1) Build driverlib SDK files in Zephyr, in ext/hal/ti/cc3200/*
2) Link directly with the driverlib.a, from an externally installed
TI CC3200 SDK.
A new option is added to replace option 2), and is now the default:
3) Use the driverlib functions already provided in ROM.
This enables a savings in code size, which will depend on the
types of device drivers configured and the number of SDK
APIs actually used.
A rom_report build of the shell sample application showed
a savings of about 2kb in code space using this new config option.
Change-Id: Ie1ede6f7aacd23db20f5292e776f1dfeab5c7fe0
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The cortex-m7 is an implementation of armv7-m. Adjust the Kconfig
support for cortex-m7 to reflect this and drop the unnecessary,
explicit, conditional compilation.
Change-Id: I6ec20e69c8c83c5a80b1f714506f7f9e295b15d5
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Precursor patches have arranged that conditional compilation hanging
on CONFIG_CPU_CORTEX_M3_M4 provides support for ARMv7-M, rename the
config variable to reflect this.
Change-Id: Ifa56e3c1c04505d061b2af3aec9d8b9e55b5853d
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Precursor patches have arranged all conditional compilation hanging on
CONFIG_CPU_CORTEX_M0_M0PLUS such that it actually represents support
for ARM ARMv6-M, rename the config variable to reflect this.
Change-Id: I553fcf3e606b350a9e823df31bac96636be1504f
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The ARM code base provides for three mutually exclusive ARM
architecture related conditional compilation choices. M0_M0PLUS,
M3_M4 and M7. Throughout the code base we have conditional
compilation gated around these three choices. Adjust the form of this
conditional compilation to adopt a uniform structure. The uniform
structure always selects code based on the definition of an
appropriate config option rather the the absence of a definition.
Removing the extensive use of #else ensures that when support for
other ARM architecture versions is added we get hard compilation
failures rather than attempting to compile inappropriate code for the
added architecture with unexpected runtime consequences.
Adopting this uniform structure makes it straight forward to replace
the adhoc CPU_CORTEX_M3_M4 and CPU_CORTEX_M0_M0PLUS configuration
variables with ones that directly represent the actual underlying ARM
architectures we provide support for. This change also paves the way
for folding adhoc conditional compilation related to CPU_CORTEX_M7
directly in support for ARMv7-M.
This change is mechanical in nature involving two transforms:
1)
#if !defined(CONFIG_CPU_CORTEX_M0_M0PLUS)
...
is transformed to:
#if defined(CONFIG_CPU_CORTEX_M0_M0PLUS)
#elif defined(CONFIG_CPU_CORTEX_M3_M4) || defined(CONFIG_CPU_CORTEX_M7)
...
2)
#if defined(CONFIG_CPU_CORTEX_M0_M0PLUS)
...
#else
...
#endif
is transformed to:
#if defined(CONFIG_CPU_CORTEX_M0_M0PLUS)
...
#elif defined(CONFIG_CPU_CORTEX_M3_M4) || defined(CONFIG_CPU_CORTEX_M7)
...
#else
#error Unknown ARM architecture
#endif
Change-Id: I7229029b174da3a8b3c6fb2eec63d776f1d11e24
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Adjust the layout of various ARM assember files to conform to the norm
used in the majority of files.
Change-Id: Ia5007628be5ad36ef587946861c6ea90a8062585
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
I've moved the call for icache_setup from nanoArchInit() to
_PrepC(), because there is a lot of code executed now before
nanoArchInit() is called, and all this time the i-cache would
be off. It should be turned on as early as possible to make
initialization faster.
Change-Id: I76a809d57a1bf9aacf51e7bb9fe8c8425f37aa13
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
The 16k RAM nRF51 variants pose a challenge to get applications to fit
within the available memory. Make the default ISR stack size smaller
than the previous 2k default, but big enough to run fully functional
Bluetooth controller and host stacks.
Change-Id: Ie7c5bb21a3ba620d283e6228a2482d280f85119d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
On the nRF5x platforms we need always need the NRF_RTC_TIMER and it
depends on the CLOCK_CONTROL_NRF5. So enable all of these always.
Fixes issues if one tries to build nRF5x platforms w/o CONFIG_BLUETOOTH.
Change-Id: I0f9af785e785f37ec289a935ddf70ee6dec08cd4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These two fields in the thread structure control the preemptibility of a
thread.
sched_locked is decremented when the scheduler gets locked, which means
that the scheduler is locked for values 0xff to 0x01, since it can be
locked recursively. A thread is coop if its priority is negative, thus
if the prio field value is 0x80 to 0xff when looked at as an unsigned
value.
By putting them end-to-end, this means that a thread is non-preemptible
if the bundled value is greater than or equal to 0x0080. This is the
only thing the interrupt exit code has to check to decide to try a
reschedule or not.
Change-Id: I902d36c14859d0d7a951a6aa1bea164613821aca
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Some thread fields were 32-bit wide, when they are not even close to
using that full range of values. They are instead changed to 8-bit fields.
- prio can fit in one byte, limiting the priorities range to -128 to 127
- recursive scheduler locking can be limited to 255; a rollover results
most probably from a logic error
- flags are split into execution flags and thread states; 8 bits is
enough for each of them currently, with at worst two states and four
flags to spare (on x86, on other archs, there are six flags to spare)
Doing this saves 8 bytes per stack. It also sets up an incoming
enhancement when checking if the current thread is preemptible on
interrupt exit.
Change-Id: Ieb5321a5b99f99173b0605dd4a193c3bc7ddabf4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Use least significant bits for common flags and high bits for
arch-specific ones.
Change-Id: I982719de4a24d3588c19a0d30bbe7a27d9a99f13
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This will allow for an enhancement when checking if the thread is
preemptible when exiting an interrupt.
Change-Id: If93ccd1916eacb5e02a4d15b259fb74f9800d6f4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
GCC 6.x for ARC does not recognize the options
-mARCv2EM and -mav2em anymore.
Both options replaced in Makefile by -mcpu=quarkse_em.
Change-Id: I9dec26dd64b4738976704a39455fe4241406db9e
Signed-off-by: Juro Bystricky <juro.bystricky@intel.com>
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
GCC 6.x for ARC does not recognize the options
-mARCv2EM and -mav2em anymore.
Both options replaced in Makefile by -mcpu=arcem.
Change-Id: Ic86bf51cd5fb1a67ba2cd75998cd907e26996347
Signed-off-by: Juro Bystricky <juro.bystricky@intel.com>
This option has side effects. It also tells the compiler not to generate
these checks in the first place. The checks call abort() which doesn't
exist in our environment.
This patch gets rid of linker errors due to missing abort() in the 0.9 SDK.
Change-Id: Ibc5aeb5458d0bded714c9c074cdf08112733428b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The Cortex-M0(+) and in general processors that support only the ARMv6-M
instruction set have a reduced set of registers and fields compared to
the ARMv7-M compliant processors.
This change goes through all core registers and disables or removes
everything that is not part of the ARMv6-M architecture when compiling
for Cortex-M0.
Jira: ZEP-1497
Change-id: I13e2637bb730e69d02f2a5ee687038dc69ad28a8
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
replace include <nanokernel.h> with <kernel.h> everywhere and also fix
any remaining mentions of nanokernel.
Keep the legacy samples/tests as is.
Change-Id: Iac48447bd191e83f21a719c69dc26233216d08dc
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable arc to access the i2c controller on I/O fabric.
There are two i2c controllers on quark se SoC. One is attached
to the I/O fabric and the other one is in the sensor system.
X86 cpu is only able to access the i2c controller on the I/O
fabric and the access is supported by existing code. HW allows
arc to access both controllers. But, the existing code only
gives arc access to the controller in the sensor sub-system.
Let's grant arc the access to the controller on I/O fabric as
well by the following changes.
1. Add i2c_qmsi.c into arc compilation.
2. Use the already defined macros to choose interrupt numbers
and do interrupt unmasking automatically based on the
compilation targets.
3. Add new symbols in Kconfig including driver names for both
controllers
Jira: ZEP-1189
Change-Id: I317da6038c50e0c8bd16f446182c1f8bdf6d3ba2
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Enable arc to access the spi controller on I/O fabric.
There are two spi controllers on quark se SoC. One is attached
to the I/O fabric and the other one is in the sensor system.
X86 cpu is only able to access the spi controller on the I/O
fabric and the access is supported by existing code. HW allows
arc to access both controllers. But, the existing code only
gives arc access to the controller in the sensor sub-system.
Let's grant arc the access to the controller on I/O fabric as
well by the following changes.
1. Add spi_qmsi.c into arc compilation.
2. Use the already defined macros to choose interrupt numbers
and do interrupt unmasking automatically based on the
compilation targets.
3. Add new symbols in Kconfig including driver names for both
controllers
Jira: ZEP-1190
Change-Id: I40a5d423d4b7986a897834d1a3831938005eda6f
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
HW allows both arc and x86 to access the pwm attached to the
quark soc I/O fabric. The existing code only allows x86 to
do this. Let's give arc the access.
Change-Id: Ie88649fea41bf86b84876c260f97dd4c12fd0b81
Signed-off-by: Baohong liu <baohong.liu@intel.com>
Obsolete, replaced by _set_thread_return_value().
Change-Id: I23e9cfc07e43542f0965817edc3552d456fd2ef3
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Previously, UART clock enable was done in pinmux init.
This is now moved into soc initialization, along with other
power related initialization routines.
Change-Id: I1f9464655ad966e9caac2d238006f12a06b202ab
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
To make way for the upcoming blinky and GPIO support for nRF5x-based
boards, this change addresses the hardcoded dependencies in Kconfig
default configurations of the different boards, moving the common option
defaults to the SoC default configuration itself.
Change-Id: I8db0750311ad5a12b76237b39438376f20f6f496
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/basic/blinky
- samples/basic/disco
- samples/basic/button
All 4 GPIO ports are supported.
Change-Id: If8599a23c1d56cfd678a6e2e5339f7e093c6061a
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The new Nordic nRF52840 IC is the latest member of the nRF52 family.
It supports the following features among others:
* Cortex-M4F core at 64MHz
* 1024KB of flash and 256KB of RAM
* Bluetooth 5-ready and 802.15.4 compatible radio
* USB device support
* NFC Tag support
* Quad-SPI
* Hardware accelerated crypto engine
http://www.nordicsemi.com/eng/Products/nRF52840
JIRA: ZEP-1418
Change-Id: I677c787bb33d02695e057d5dced7e3455b9f6c50
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In preparation for the upcoming nRF52840 support, this patch refactors
the nRF52 series support code to allow for future members of the IC
family to be added, while keeping everything that is common together.
JIRA: ZEP-1418
Change-Id: I4200064ca888d72ba0b8629ce94e4ea6384099ad
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Also remove mentions of unified kernel in various places in the kernel,
samples and documentation.
Change-Id: Ice43bc73badbe7e14bae40fd6f2a302f6528a77d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move logging out of misc/ to its own subsystem. Anything related to
logging and any new logging features or backends could be added here
instead of the generic location in misc/ which is overcrowded with
options that are not related to eachother.
Jira: ZEP-1467
Change-Id: If6a3ea625c3a3562a7a61a0ba5fd7e6ca75518ba
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
rename NANOKERNEL_TICKLESS_IDLE_SUPPORTED to
TICKLESS_IDLE_SUPPORTED and remove nanokernel occurances in Kconfig
files.
Make TICKLESS_IDLE depend on hardware that supports it.
Change-Id: I6a2e4fb0f7cf4b45475b48e71823ea089ee98759
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Also remove some old cflags referencing directories that do not exist
anymore.
Also replace references to legacy APIs in doxygen documentation of
various functions.
Change-Id: I8fce3d1fe0f4defc44e6eb0ae09a4863e33a39db
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
That module is not used anymore: it was introduced pre-Zephyr to add
some kind of awareness when debugging ARM Cortex-M3 code with GDB but
was never really used by anyone. It has bitrotted, and with the recent
move of the tTCS and tNANO data structures to common _kernel and
k_thread, it does not even compile anymore.
Jira: ZEP-1284, ZEP-951
Change-Id: Ic9afed00f4229324fe5d2aa97dc6f1c935953244
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The K64F board has the ENET ethernet driver. Behavior consistently
with other driver selection logic and default the KSDK ethernet driver
on if ETHERNET drivers are enabled.
Change-Id: I2fbed7fdef22d75cf163b61b3e0530ce00d988f0
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
And also remove now obsolete ARCH_HAS_TASK_ABORT.
ARC does not need the options either.
Change-Id: Ie52d63178a367ce12b911dacfe2d389f4f75ed2d
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
For very constrained systems, like bootloaders.
Only the main thread is available, so a main() function must be
provided. Kernel objects where pending is in play will not behave as
expected, since the main thread cannot pend, it being the only thread in
the system. Usage of objects should be limited to using K_NO_WAIT as the
timeout parameter, effectively polling on the object.
Change-Id: Iae0261daa98bff388dc482797cde69f94e2e95cc
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
- does not pull in printk(), for potential footprint gain
- does not pull in k_thread_abort(), for single-threaded systems
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Change-Id: Ibc6a198b81a6cd73117d1e85aa05b92a4501a34d
Some kernel operations, like scheduler locking can be optmized out,
since coop threads lock the scheduler by their very nature. Also, the
interrupt exit path for all architecture does not have to do any
rescheduling, again by the nature of non-preemptible threads.
Change-Id: I270e926df3ce46e11d77270330f2f4b463971763
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
nano_cpu_idle/nano_cpu_atomic_idle were not ported to the unified
kernel, and only the old APIs were available. There was no real impact
since, in the unified kernel, only the idle thread should really be
doing power management. However, with a single-threaded kernel, these
functions can be useful again.
The kernel internals now make use of these APIs instead of the legacy
ones.
Change-Id: Ie8a6396ba378d3ddda27b8dd32fa4711bf53eb36
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The way the ready thread cache was implemented caused it to not always
be "hot", i.e. there could be some misses, which happened when the
cached thread was taken out of the ready queue. When that happened, it
was not replaced immediately, since doing so could mean that the
replacement might not run because the flow could be interrupted and
another thread could take its place. This was the more conservative
approach that insured that moving a thread to the cache would never be
wasted.
However, this caused two problems:
1. The cache could not be refilled until another thread context-switched
in, since there was no thread in the cache to compare priorities
against.
2. Interrupt exit code would always have to call into C to find what
thread to run when the current thread was not coop and did not have the
scheduler locked. Furthermore, it was possible for this code path to
encounter a cold cache and then it had to find out what thread to run
the long way.
To fix this, filling the cache is now more aggressive, i.e. the next
thread to put in the cache is found even in the case the current cached
thread is context-switched out. This ensures the interrupt exit code is
much faster on the slow path. In addition, since finding the next thread
to run is now always "get it from the cache", which is a simple fetch
from memory (_kernel.ready_q.cache), there is no need to call the more
complex C code.
On the ARM FRDM K64F board, this improvement is seen:
Before:
1- Measure time to switch from ISR back to interrupted task
switching time is 215 tcs = 1791 nsec
2- Measure time from ISR to executing a different task (rescheduled)
switch time is 315 tcs = 2625 nsec
After:
1- Measure time to switch from ISR back to interrupted task
switching time is 130 tcs = 1083 nsec
2- Measure time from ISR to executing a different task (rescheduled)
switch time is 225 tcs = 1875 nsec
These are the most dramatic improvements, but most of the numbers
generated by the latency_measure test are improved.
Fixes ZEP-1401.
Change-Id: I2eaac147048b1ec71a93bd0a285e743a39533973
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The Cortex-M3/4 kernel was reserving priorities 0 and 1 for itself, but
was not registering any exception on priority 0. Only reserve priority 0
and use it for SVC and fault exceptions instead of priority 1.
Change-Id: Iff2405e27fd4bed4e49ab90ec2ae984f2c0a83a6
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Cortex-M0/M0+ do not have other faults than the hard fault at priority
-1, so they do not need to reserve a priority to allow exceptions to
trigger during handling of ISRs.
Change-Id: I479e439f7bcac70b4b2b787bcd744a4c65437e80
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This allows using it in _EXC_PRIO() instead of hardcoding 2 and 3.
Change-Id: I3549be54602643e06823ba63beb6a6992f39f776
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Use it to flag which CPUs can do zero latency interrupts, which depend
on being able to lock up to a specific interrupt priority.
Change-Id: I09f71366ea1d05486e38c513a09abc270884879f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
When going into DEEP_SLEEP mode, the ARC core now saves
its context. This includes:
- All core registers
- Stack pointer
- Program counter (restored by jumping to the restore code)
The arc reset code now checks if the GPS0 bit 2 is set.
This is similar to the behavior of the x86 core done by
the QMSI bootloader which is setting GPS0 bit 1 in order
to call the restore path instead of cold boot path.
The sample has been adapted in order to support the ARC.
Jira: ZEP-1222
Change-Id: I375f03b16b8a5fd1f07ead55cf7e4947d6290c9f
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
In order to resume the ARC from deep sleep,
the interrupts need to be restored.
The FIRQ stack needs to be saved and restored
when performing sleep operations.
During early initialization, the sp in the 2nd register bank
is made to refer to _firq_stack.
This allows for the FIRQ handler to use its own stack.
Fast Interrupts cannot be used after sleep if this information
is not restored.
This patch adds the suspend and resume functions.
Jira: ZEP-1223
Change-Id: Ic81980f05aee6c1f7b8c46c743f2648c65b29486
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Move interrupt initialization for the ARC to its own
device. The init function for the arc will be only
doing platform specific operations
Jira: ZEP-1288
Change-Id: Icb04c3622890021c65cd24cecf6cafee6c37caf9
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
As flags are modified when entering sleep, add cc to
clobber list.
Jira: ZEP-1408
Change-Id: Ia80bc1c7ddedb9d9963c47108372a90928597c1d
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
The ARG_UNUSED macro is added to avoid compiler warnings.
Change-Id: If0242548849ee5b258bb3fce9fd727b377411343
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Add a "memory" clobber to inline asm SVC call to ensure the compiler
does not reorder the instruction relative to other memory accesses.
Issue found by inspect the source code. There is no evidence to
suggest that this bug will manifest for any current ARM target using a
current compiler.
Change-Id: I32b1e5ede02a6dbea02bb8f98729fff1cca1ef2a
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Basic interrupt driven driver for the nRF5 onboard temperature sensor.
Change-Id: Id0ac303293b8e8b8285b19bcda31284ee6617105
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Stop using the specific k64 pinmux driver by default and start using the
more generic ksdk pinmux driver instead.
Jira: ZEP-1393
Change-Id: Id65b59518c386e6ba33cfa5c4c5bd541664d2b41
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Following pinmux update for PWM support,
update soc to support this new configuration.
Change-Id: I1126e347ab1ab6b2d830993e548de8f32fa2f8f9
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds the boot time Power Management configuration for Beetle
on Zephyr. In particular it defines the states of the peripherals during
sleep and deep sleep and the allowed wakeup sources.
Jira: ZEP-1300
Change-Id: Iad9c0f851771ea60d94bbe5420b7b3ee0743b77e
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add one pin configuration for I2C1 of the STM32L4 series.
Change-Id: Id05d916f2a1126ca439aebcddd8dc9c91015f6fe
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the pin configuration of the USARTs.
Change-Id: Idf7a18b6eab95c61870ad4850c9eafb1fdcab03d
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the clock driver for the STM32L4 series.
Change-Id: Icdf79061f163d8d00187b382d1564422fb875c5b
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the initial SoC support for the STM32L4XX family. The code was
tested on STM32L476RG, but should work on any STM32L4XX currently
available.
This implementation was inspired by the stm32f1x implementation.
Change-Id: Id6670bce0c423617284e8467a9c461531f948e0f
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
There was a misalignment between Zephyr UART device numbering and
SoC UART IP. Device "UART_1" was mapped to IP USART_2, which could
be confusing for user.
This commit allows to align "UART_1" to IP USART_1.
Change is propagated to all STM32F103RB/STM32F401RE based boards and
respective pinmux drivers
Change-Id: Ia8099dfeec7b9c0c686c2a58ccb4dbb1a55b6537
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Due to new serial driver implementation based on STM32Cube we can
remove the USARTX_ADDR defines as they aren't ended anymore
Change-Id: Ia9f9b0a2a63280c0221c789a53ff7338bda17dfb
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Due to new serial driver implementation based on STM32Cube we can
remove the USARTX_ADDR defines as they aren't ended anymore
Change-Id: Icd5b7995429025c5b54b1a04ca6abb9649ab31c8
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32Cube based implementation allows single driver file for
all stm32 based SoCs.
By maximizing code reuse, use of STM32Cube eases new SoCs
porting into Zephyr and provides better maintanability and
maturity.
Change-Id: Ief4b723add3dfc8b2a839683559c5a4c5d5eb837
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch fixes the unused parameter warning found at the
quark_x1000/soc.h file.
Change-Id: I110d7185d8302f95d14efd13060055e7378aea23
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch fixes the unused parameter warning found at the
arch/arm/core/fault.c and arch/arm/soc/st_stm32/stm32f1/soc_gpio.c
files.
Change-Id: I5b3013c1514cff30f4e98feb31169fb28546c534
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Memory access could be reorderd around sleep. Add memory
in clobber list.
Jira: ZEP-1408
Change-Id: I49df2542e0059ba76a262fbda58eb46b86e89bea
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
A build error was resulting if CONFIG_ARC_STACK_CHECKING is enabled.
There is a breq that was too far. Adding conditional code to
re-arrange the branching so that it can be done.
See ZEP-1116.
Change-Id: Idea85817b2e05617bbaa4450437aa74c5737e213
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Zephyr is always setting irqs to be level triggered as
required by the core. It is unnecessary to set it to
level again while entering sleep states.
Change-Id: I10f919d619af2e1ab05dc85a67766929b6ae9402
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Too much code might run with a stale icache, before _PrepC(), so move
the invalidation/disabling code earlier. The asm code does the exact
same thing disable_icache() and invalidate_dcache() were doing.
Change-Id: If52f4e4a1de546fb82873c91ead95614a44b106d
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
We have no idea what's in the GDT if we don't set it ourself.
Change-Id: I3c2e406370e3ea149252c423d66c97aab95bee17
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Initializing the interrupt stack before initializing (turning off) the
watchdog on the FRDM board pushed the initialization of the watchdog too
late, causing it to fire and reset the board. The board would be kept in
a reboot loop.
Move the initialization of the watchdog earlier: this runs on the main
stack now, instead of the interrupt stack, the same stack the interrupt
stack initalization code runs on.
Change-Id: Ic0006f4f4f4090393571d8355a80dc9390c9fbc6
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
When sleep instruction is called with interrupts enabled, the
interrupt priority threshold bits need to be set. Only interrupts
with equal or higher priority will wake the sleep. Currently it
is set to 0 unintentionally and only priority 0 interrupt can
wake the sleep.
Jira: ZEP-1349
Change-Id: I927e259345cc37c5ecc4dfdcde996dd16443e61b
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
The cpu context save function was manipulating stack and
returning to C caller. This can corrupt stack if the calling
function has data saved and it pops before entering deep
sleep. Moved sleep functions into assembly to avoid this.
Jira: ZEP-1345
Change-Id: I8a6d279ec14e42424f764d9ce8cbbef32149fe84
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
The nRF5x series SoCs do not implement systick, hence we disable
CORTEX_M_SYSTICK.
Instead, use nRF SoC Series NRF_RTC1 for system clock interfaces.
The kernel system clock interface is implemented using the low
power real time counter NRF_RTC1. NRF_RTC0 is used by the BLE
controller.
In addition, cleanup nRF5x series defconfig to be consistent.
Jira: ZEP-742
Jira: ZEP-1308
Jira: ZEP-1315
Change-id: I0f6cc1836fe0820a65f2cbb02cf5ae7e9eb92e1d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Make the systick feature optional that can be selected by the SoC.
Change-Id: I4a405640b84daecc17fc1882743d3cafb78ff861
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
An IRQ would always register as a ZIL interrupt.
Change-Id: If82a85f472a60512745652aacc7e8b7dfacaa268
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
There is no FIRQ stack in the system in this case, so do not initialize
it.
Change-Id: I8bc068ce43ac8a39909994d8cc01ba0c6a17f4ae
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Also remove NO_METRIC, which is not referenced anywhere anymore.
Change-Id: Ieaedf075af070a13aa3d975fee9b6b332203bfec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The assembler was passed immediate values that are too large for the
limited Cortex-M0 thumb assembly. Load values in registers instead of
using immediate values.
Change-Id: Ib5541c92dea03e0efb1b88ab91eeb408d151a71b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This patch enables REBOOT when RUNTIME_NMI is selected via defconfig
file. This action is required to prevent compilation errors.
Change-Id: I67c18b2860ac34ba8f96e780737b4857a6063ece
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If CORTEX_M_SYSTICK is not selected, do not reference
_timer_int_handler. SoC will need to define a custom system
clock implementation.
Change-Id: I655f3abf66953e434fef69ed16db2d9c2dcc486e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Zephyr kernel is unable to compile when CONFIG_RUNTIME_NMI is enabled in
defconfig on ARM's architectures.
This patch addresses the following issues:
* In nmi.c _DefaultHandler() is referencing a function
(_ScbSystemReset()) not defined in Zephyr. This has now been replaced
with sys_arch_reboot.
* nmi.h is included in ASM files and due to the usage of "extern" the
compilation ends with an error. Added the directive _ASMLANGUAGE to
prevent the problem.
Jira: ZEP-1319
Change-Id: I7623ca97523cde04e4c6db40dc332d93ca801928
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Move _thread_base initialization to _init_thread_base(), remove mention
of "nano" in timeouts init and move timeout init to _init_thread_base().
Initialize all base fields via the _init_thread_base in semaphore groups
code.
Change-Id: I05b70b06261f4776bda6d67f358190428d4a954a
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Use the main stack during very early boot so that we can call memset on
the interrupt and FIRQ stacks. Iniitalize the them before one of them is
used for the rest of the pre-kernel initialization.
Change-Id: Ib57856a66273dda9382e08fa91da5a54847b77c2
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Use the main stack during very early boot so that we can call memset on
the interrupt stack. Initialize the interrupt stack before it is used
for the rest of the pre-kernel initialization.
Change-Id: I6fcc9a08678afdb82e83465cda1c7a2a8c849c9b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Same issue as with ARM. ARC can use _Swap() though, because the call to
it is serial, not generating a low-priority exception and interrupts are
locked until the main() thread is context-switched into and the
interrupt stack is released.
Fixes ZEP-1310.
Change-Id: Ie1f27f7ad0502191ca2867b5400d6e0bfb7f0fc6
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The ARM Cortex-M early boot was using a custom stack at the end of the
SRAM instead of the interrupt stack. This works as long as no static
data that needs a known initial value occupies that stack space. This
has probably not been an issue because the .noinit section is at the
very end of the image, but it was still wrong to use that region of
memory for that initial stack.
To be able to use the interrupt stack during early boot, the stack has
to be released before an interrupt can happen. Since ARM Cortex-M uses
PendSV as a very low priority exception for context switching, if a
device driver installs and enables an interrupt during the PRE_KERNEL
initialization points, an interrupt could take precedence over PendSV
while the initial dummy thread has not yet been context switched of and
thus released the interrupt stack. To address this, rather than using
_Swap() and thus triggering PendSV, the initialization logic switches to
the main stack and branches to _main() directly instead.
Fixes ZEP-1309
Change-Id: If0b62cc66470b45b601e63826b5b3306e6a25ae9
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Artifact from microkernel, for handling multiple pending tasks on
nanokernel objects.
Change-Id: I3c2959ea2b87f568736384e6534ce8e275f1098f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
PA10 should use *_PA10_UART1_RX
Change-Id: Ifba4d301d049db1d62ea3a63d4d66f75c88a71a6
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Previous configuration was backwards. From the Intel manual:
"If the segment descriptors in the GDT or an LDT are placed in ROM,
the processor can enter an indefinite loop if software or the
processor attempts to update (write to) the ROM-based segment
descriptors. To prevent this problem, set the accessed bits
for all segment descriptors placed in a ROM. Also, remove
operating-system or executive code that attempts to modify
segment descriptors located in ROM."
Only by some miracle has this not been causing problems.
Change-Id: I0bb915962a1069876d2486473760112102feae7b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Prio should be an int, since values are small integers, not a fixed-size
int32_t. It aligns with the prio parameters of the other APIs.
Stack size should be size_t.
Change-Id: Id29751b86c4ad7a7c2a7ffe446c2a96ae83c77bf
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The bitfield determining the I/O direction already defines the pin
as either input or output, cannot be none or both at the same time
This issue was reported by Coverity
Coverity-CID: 151970
Change-Id: I18d5387139d6834004ba3269c5b54176bdc97ea7
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
There was a possible race condition when setting the return value of a
thread that is pending, from an ISR.
A kernel function causes a thread to pend, with the following series of
steps:
- disable interrupts
- move current thread to wait_q
- call _Swap
Depending if running on M3/4 or M0+, _Swap will either issue a svc #0,
or pend PendSV directly. The same problem exists in both cases.
M3/4:
__svc will:
- enable interrupts
- trigger __pendsv
M0+:
_Swap() will enable interrupts.
__pendsv will:
- save register context including PSP into the thread struct
If an interrupt occurs between interrupts being enabled them and
__pendsv saving PSP, and the ISR sets the pending thread's return value,
this will happen:
- sees the thread in a wait_q
- removes it
- makes it ready
- calls _set_thread_return_value
- _set_thread_return_value looks at the thread's saved PSP to poke
the value
In this scenario, PSP hasn't yet been updated by __pendsv so it's a
stale value from the previous context switch, resulting in unpredictable
word on the stack getting set to the return value.
There is no way to fix this issue and still have the return value being
delivered directly in the pending thread's exception stack frame, in the
M0+ case. There will always be a window between the unlocking of
interrupts and PendSV being handled. On M3/4, it could be possible with
the mix of SVC and PendSV, since the exception stack frame is created in
the __svc handler. However, because we want to keep the two
implementations as close as possible, and there were talks of moving
M3/4 to using PendSV only, to save an exception, the approach taken
solves both cases.
The approach taken is similar to the ARC and Nios2 ports, where
there is a field in the thread structure that holds the return value.
_Swap() then loads r0/a1 with that value just before returning.
Fixes ZEP-1289.
Change-Id: Iee7e06fe3f8ded84aff918fd43408c7f589344d9
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
When a thread dies, at least print the pointer to it, so we can debug
better.
Change-Id: Ief6bbc0c221e2d5271c240a4b73df16413aa5e22
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Most kernel APIs are now ready for inclusion in the API guide.
The APIs largely follow a standard template to provide users
of the API guide with a consistent look-and-feel.
Change-Id: Ib682c31f912e19f5f6d8545d74c5f675b1741058
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
This reverts commit
"kernel/arm: add comment about _is_next_thread_current"
and fixes the interrupt locking issue.
The comment would have been right if only reads were done the ready
queue, but that is not the case. It turns out that the comment was written
ignoring the fact that _is_next_thread_current() updates the next thread
cache when fetching the next thread.
Change-Id: I21c9230f85f4f87a6bbf14fd4a9eb7e19b59f8c5
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Though Cortex-M4 could optionally have a floating point unit,
the MCU in the cc3200 in fact does not have an FPU.
Enabling CPU_HAS_FPU caused applications built with CONFIG_FLOAT=y
to crash during an early call to enable_floating_point().
This patch was validated by running microPython, which is one
such application.
Change-Id: I8bfd42c456524e152cbbb983001d9540d93fbe98
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Normally, _is_next_thread_current() must be called with interrupts
locked, but the ARM interrupt exit code does not have to do that. Add
explanation why.
Change-Id: Id383b47a055fdd6fbd5afffa52772e92febde98f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Move away from legacy APIs and use unified kenrel instead.
Change-Id: Icae86beec66df1b041405cbe3455913630fc8ad1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There was a lot of duplication between architectures for the definition
of threads and the "nanokernel" guts. These have been consolidated.
Now, a common file kernel/unified/include/kernel_structs.h holds the
common definitions. Architectures provide two files to complement it:
kernel_arch_data.h and kernel_arch_func.h. The first one contains at
least the struct _thread_arch and struct _kernel_arch data structures,
as well as the struct _callee_saved and struct _caller_saved register
layouts. The second file contains anything that needs what is provided
by the common stuff in kernel_structs.h. Those two files are only meant
to be included in kernel_structs.h in very specific locations.
The thread data structure has been separated into three major parts:
common struct _thread_base and struct k_thread, and arch-specific struct
_thread_arch. The first and third ones are included in the second.
The struct s_NANO data structure has been split into two: common struct
_kernel and arch-specific struct _kernel_arch. The latter is included in
the former.
Offsets files have also changed: nano_offsets.h has been renamed
kernel_offsets.h and is still included by the arch-specific offsets.c.
Also, since the thread and kernel data structures are now made of
sub-structures, offsets have to be added to make up the full offset.
Some of these additions have been consolidated in shorter symbols,
available from kernel/unified/include/offsets_short.h, which includes an
arch-specific offsets_arch_short.h. Most of the code include
offsets_short.h now instead of offsets.h.
Change-Id: I084645cb7e6db8db69aeaaf162963fe157045d5a
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The unified kernel is now the only supported kernel, so this
option is unnessary. Eliminating this option also enables
the removal of some legacy code that is no longer required.
Change-Id: Ibfc339d643c8de16a2ed2009c9b468848b8b4972
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Add support for console output via the USB UART.
Note that console input via the USB UART doesnt work.
Adds a simulated poll method for UART interface exposed by USB.
Jira : ZEP-775
Change-Id: I357827ea52c027eb000baed80225f422df1f3358
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Regardless of the number of interrupt priorities
supported, the exit of the trap handler can check
AUX_IRQ_ACT to see if it interrupted a FIRQ or IRQ.
Change-Id: I0b84d8298d3e6e437c934c01db4535fa8fe29458
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Some arduino 101 boards have old boot loader without context
restore boot flow feature. This handler will allow doing deep sleep
in those boards by jumping to the context restore code. This will
be disabled by default and can be optionally enabled by user.
Jira: ZEP-1258
Change-Id: I92e70550fd92c1cac42b3039d667fb0be8cf5bce
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Some bootloaders have power management support to restoer context
upon resume from deep sleep. In such cases, the OS startup code
should call the notification hook. Create Kconfig flags to configure
this option.
Jira: 1257
Change-Id: I9f40c5fa077c2f17dc8e9f11604c3ed17e549ed5
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
_sys_soc_resume hook is over loaded to handle to different
scenarios. It is primarily called to notify exit of kernel idling
after PM operations. It is also used to notify exit from deep sleep.
This is very confusing and also makes the implementation of the
hook function very difficult because of very different conditions
involved in the 2 different use cases. Further, users may not require
either or both use cases depending of their custom boot flow and
power state handling. To simplify, create a separate hook for the
purpose of deep sleep exit notification. Use the existing one to
only notify kernel idling exit after PM operations.
Jira: ZEP-1256
Change-Id: I96350199a0fd37f16590c8ee5302a94a3d71b8ba
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Add SoC support for ARM Beetle platform.
Beetle is an ARM Cortex-M3 based SoC used on ARM V2M Beetle Boards.
https://www.arm.com/products/tools/development-boards/versatile-express/beetle_iot_evaluation_platform.php
This patch contains:
* The base SoC platform.
* The clock_init functionality.
* The system wide pin definitions.
* The configuarion for the drivers at SoC level (IRQs, PINs and
Base Addr).
Jira: ZEP-1245
Change-Id: If15675935890711983e5ce37d49732b0462c3ec7
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When waking up from C2LP state, the timer needs
to be reinitialized as we cannot know the time
that we spent in that state.
In order to reschedule the user application, expire it
as soon as we restart.
Change-Id: Id38a0de71e148ae8d9024a36d3983ab57b1e40d2
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Add Low Power States support to the power shim layer
and show the usage in the quark_se sample.
States are defined as follow:
- SYS_POWER_STATE_CPU_LPS: SS2 with LPSS enabled
- SYS_POWER_STATE_CPU_LPS_1: SS2 with LPSS disabled
- SYS_POWER_STATE_CPU_LPS_2: SS1 with LPSS disabled
Jira: ZEP-994
Change-Id: Ie4b93f6e539cb53fc035be00280b66b2cb0d9fea
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Updates x86 floating point support to reflect changes that have
been made in recent months.
* Many, many, many cosmetic changes (mostly revisions to comments).
* Elimination of unnecessary function aliases that were needed
to support the task and fiber versions of certain APIs.
* Elimination of run-time code to enable a thread's "FP regs"
option bit if the "SSE regs" option bit was set. The kernel
now recognizes that the thread is using the FPU as long as
either option bit is set. (If the thread has both option bits
enabled this is the same as if only the "SSE regs" bit is set.)
Change-Id: Ic12abc54b6fa78921749b546d8debf23e7ad232d
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Verify the thread priorities are within the bounds when starting a new
thread and when changing the priority of a thread.
Change-Id: I007b3b249e4b80235b6439cbee44cad2f31973bb
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
A race condition would happend if a FIRQ interrupted a
return-from-interrupt from a RIRQ at the wrong moment: if a decision was
already taken which thread to context switch in and the FIRQ woke up
another thread of higher priority, the ready queue would be corrupted.
The solution is to lock interrupts at the moment the interrupt return
code starts looking at the kernel queues. Interrupts do not need to be
unlocked before exiting: the return-from-interrupt (rtie) instruction
will restore the correct interrupt locking state for the thread being
context switched in.
Change-Id: I777665c2faeca7b1f2a77ddd9ee2a520080bae88
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The bitwise AND operator was being applied to the boolean expression
"!shared_data->flags" instead of the whole expression because a
parenthesis was lacking.
This bug has been found using Coccinelle using the following spatch,
after finding a similar bug somewhere else in the code base:
@@
expression E1;
expression E2;
@@
- !E1 & E2
+ !(E1 & E2)
No other instance of this defect has been found with this spatch.
Change-Id: I6b9ca092f4015c80ddc83c31ce540a92e67cdb11
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
An implementation to flush multiple d-cache lines has been added
per the top-level cache.h API. ZEP-1153 was opened to express
the need for MORE i-cache and d-cache APIs. For example, the current
cache.h API doesn't provide a means to invalidate d-cache lines
and has nothing for i-cache.
I've also modified some of the i-cache related aux registers to have
better names so that they won't be confused with d-cache.
These changes are for
ZEP-1176.
Change-Id: If4c5410451cc40dcd5618fc871093c8febf7e061
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Symbols now use the K_ prefix which is now standard for the
unified kernel. Legacy support for these symbols is retained
to allow existing applications to build successfully.
Change-Id: I3ff12c96f729b535eecc940502892cbaa52526b6
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
This KSDK flash shim driver supports the device in the FRDM K64F
platform (enabled with this commit).
WARNING: the driver disables the system interrupts for potentially
long periods of time. This is required to avoid Read-While-Write
issues since most platforms run in XIP mode.
For more detailed information see the link below:
http://cache.freescale.com/files/32bit/doc/app_note/AN4695.pdf
Change-Id: I70f8d09080251033ce2f45be0c2eb95c19fded08
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
The uart_k20 serial driver incorrectly assumed that all instances of the
UART peripheral are driven by the system clock, when actually some
instances are driven by the bus clock (which usually runs at half the
system clock). This caused incorrect baud rate calculations for UART
instances driven by the bus clock (UART2-4).
Change-Id: I38041781cdee146912bb5167e7c71d6416b966b5
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This change is required to support unified kernel.
Change-Id: I47bd644239eb3e624c7a5cb456eedad5aca79e8e
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The unified kernel expect the default return value from a _Swap() call
to be set to -EAGAIN by the architecture code. Cortex-M3/M4 does this in
the SVC call handler, and it was missing from the Cortex-M0/M0+ before
pending PendSV.
Change-Id: I3316901186ab409f49043eb4f1972c4b0dd9a4a2
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/hello_world
- samples/philosophers
- samples/drivers/uart
- samples/shell
UARTA0 is currently supported.
Change-Id: I85727c622d4d42183cc9f2f8b43d653e245dd17e
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Initial support is for the CC3200 SoC, comprising a network coprocessor
and Cortex-M4 MPU.
This leverages the CC3200 SDK driver peripheral library, installed
separately, or built from ext/hal/.
Jira: ZEP-1109
Change-Id: I508afc8596c165b309a4ec641c39abadc779eea3
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The k64 SoC has multiple instances of many peripherals, but which
instances can actually be used depends upon the board design and pinmux
configuration.
Move all instance-specific default driver configurations from the SoC to
the boards (frdm_k64f and hexiwear_k64). Default driver selection
remains in the SoC (e.g., enable the KSDK I2C driver when I2C is
enabled).
This paves the way to support different driver defaults for the
frdm_k64f and hexiwear_k64 boards, but it does not yet change any of the
default values; it only changes where the default values get set.
Change-Id: Id9ed898762eb400ecefeac91ae4dce66da05622d
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds standard prefix to symbolic option that flags a thread
as essential to system operation.
Change-Id: Ia904a81ce343fdd1cd44caaaeae641d822777f9b
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
QMSI 1.3 natively supports restoring the SoC and peripherals
after sleep.
The Zephyr Power Management shim layer is updated
in order to support QMSI functions.
The following functions have been added:
void _sys_soc_set_power_state(enum power_state);
void _sys_soc_power_state_post_ops(void);
In order to fully support deep sleep, the function
_sys_soc_set_power_state now support saving and
restoring CPU context and returns to the application.
_sys_soc_set_power_state function also abstracts
QMSI cpu states and enable the application to choose
between C1/C2 or C2LP states.
The QMSI power states are mapped as follows:
SYS_SOC_POWER_STATE_CPU_LPS -> power_cpu_c2lp
SYS_SOC_POWER_STATE_CPU_LPS_1 -> power_cpu_c2
SYS_SOC_POWER_STATE_CPU_LPS_2 -> power_cpu_c1
SYS_SOC_POWER_STATE_DEEP_SLEEP -> power_soc_deep_sleep
SYS_SOC_POWER_STATE_DEEP_SLEEP_1 -> power_soc_sleep
The following functions have been removed:
void _sys_soc_set_power_policy(uint32_t pm_policy);
int _sys_soc_get_power_policy(void);
FUNC_NORETURN void _sys_soc_put_deep_sleep(void);
void _sys_soc_put_low_power_state(void);
void _sys_soc_deep_sleep_post_ops(void);
Those changes are propagated to the samples.
All calls to QMSI are removed.
Jira: ZEP-1045, ZEP-993, ZEP-1047
Change-Id: I26822727985b63be0a310cc3590a3e71b8e72c8c
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
A new shared memory has been added to the qmsi bootloader
in order to handle the restore flow and jump to
the restore trap where context is restored.
Add the new entry to the QUARK SE C1000 linker file
and new kconfig options:
- CONFIG_BSP_SHARED_RAM_ADDR to set the address of the
shared memory.
- CONFIG_BSP_SHARED_RAM_SIZE to set the size of the
shared memory.
This is only enabled with CONFIG_SYS_POWER_DEEP_SLEEP.
Jira: ZEP-1046
Change-Id: I35d924a100c5583025aa36a9741428ab51809c57
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Enable HAS_CUBE config flag on stm32f4 family soc.h is updated to
include minimum include files from ext/hal/stm23cube
Change-Id: I35a8c33aab777167ee7029edc1b7a4f6d21fccd8
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Create HAS_CUBE config flag to control activation of STM32Cube support.
Generate fitting compilation options for STM32Cube in
/ext/hal/stm32cube/Makefile soc.h is updated to include minimum include
files from ext/hal/stm23cube
Change-Id: If58ce0a4fdb7fbf5f171dfe5f1f8eb75126a8313
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In ST CMSIS files, FLASH_BASE does not mean base address of FLASH register
Instead FLASH_R_BASE is used.
stm32f1 clock control driver is updated to be compatible with this naming.
Change-Id: Ic4fb49c60c392e15fd12c69266baf4c686bd343b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32Cube uses SoC defines made to reflect HW heterogeneity that
should be taken into account by SW.
Aim of this commit is to adapt values used by Zephyr to the same
diversity. This will help create new SoC values only when justified
by a real hardware difference that should be taken into account
by software.
For instance, for SoC stm32f401re following define is used:
*STM32F401xE
Which means:
*Same SW could be used on STM32F401RE and STM32F401CE:
same CONFIG_SOC could be used
*Different SW should be used on STMF401RE and STM32F401RC:
different CONFIG_SOC should be used
This change focuses on stm32f4xx series.
Change-Id: I56ff4d1815d09747cf722385532eb2dcbdf37b44
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32Cube uses SoC defines made to reflect HW heterogeneity
that should be taken into account by SW.
Aim of this commit is to adapt values used by Zephyr to the same
diversity. This will help create new SoC values only when justified
by a real hardware difference that should be taken into account
by software.
For instance, for SoC stm32f103rb following define is used:
*STM32F103xB
Which means:
*Same SW could be used on STM32F103RB and STM32F103VB:
same CONFIG_SOC could be used
*Different SW should be used on STMF103RB and STM32F103R4:
different CONFIG_SOC should be used
This change focuses on stm32f1xx series.
Change-Id: I5ecfaa52952d04421b27b5e74fb71b4fc108b662
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The GPIO and AON GPIO ports are available to both the x86 and ARC
cores, but the driver always assumed only the x86 at the time of
configuring interrupts.
Use the available macros to set the correct values independently of
which core it's being built for.
Jira: ZEP-1030
Change-Id: I310afcc48780fbe1cac9dc3368a6de11bd797fda
Signed-off-by: Iván Briano <ivan.briano@intel.com>
The SoC level peripherals are accesible by both cores, while the SS
ones are only available to the sensor subsystem. Since the ARC core can
make use of both drivers at the same time, we need to be able to
differentiate their configuration values somehow.
Also disable the SoC GPIO for the ARC by default, as it still needs
more changes to be usable.
Jira: ZEP-1030
Change-Id: Ic5415c404ecd32a3e560467b6f5eaa873a515d72
Signed-off-by: Iván Briano <ivan.briano@intel.com>
IRQ numbers differ between x86 and ARC, as well as the bits that need to
be touched in the interrupt routing masks. QMSI abstracts some of it and
for the rest we do have the information needed.
Add a macro to select the right IRQ number based on which core we are
building for.
Change-Id: I3e6680d10a0a23c98777d2831efe6819fcb54162
Signed-off-by: Iván Briano <ivan.briano@intel.com>
There are a number of data sections that are repeated across
all the linker scripts for various architecture. In practice these
don't always get updated and we have had problems with bit-rot.
Consolidate these to make maintenance easier.
x86 linker scripts now follow the same naming convention and we
get rid of a linker-epilog.h that wasn't necessary and whose purpose
has been lost to the mists of time. If applications want to define their
own sections they should be allowed to. Linker scripts for x86 do not
end with .h any more, they are not C header files even though we use
C's preprocessor.
Issue: ZEP-688
Change-Id: I893eb4619969695c1f980efd7c2ec9fa5dad136d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We can derive NUM_REGULAR_IRQ_PRIO_LEVELS by subtracting 1
from CONFIG_IRQ_PRIO_LEVELS if FIRQ is present (which is currently
always the case). If FIRQ is not present, the value will be equal
to CONFIG_IRQ_PRIO_LEVELS since all interrupts will be regular.
Change-Id: Ibefc939e3771bf0adf712127db0d36cb49bf732b
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Update the QMSI drop we maintain in Zephyr, and fix the build where
needed:
- QM_SCSS_INT is renamed to QM_INTERRUPT_ROUTER;
- every member of QM_INTERRUPT_ROUTER was renamed as well;
- QM_IRQ_* renamed too, mostly added _INT at the end;
- some isr functions were renamed to keep their names consistent;
- build for x86 needs to define QM_LAKEMONT, as QM_SENSOR was for ARC.
Change-Id: I459029ca0d373f6c831e2bb8ebd52402a55994d1
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Move common config options one level up to try to simplify the per-board
defconfig
Change-Id: I3d80fa494050634d0f877af2015b01b85df20d1d
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the STM32F401 chip on the board
Change-Id: I96c0799f3658ecea096fa5971bce9faf21919ee1
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32F401 allows for upto 16 alternate functions on each pin.
Change-Id: Ib1c14fd31abaa2b05a5ab0f7bd1b4a4748f10f84
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implements MCU-specific GPIO input interrupt integration. Added
definition of System configuration controller as well as its needed by
the GPIO code.
The SYSCFG controller is used for system-specific configuration such as:
- remap the type of memory accessible at address 0x00000000
- manage the external interrupt line connection to GPIOs
- configure the I/O compensation cell
Change-Id: Id2ebfbd1b21e77be76406d1cd6cd5d4989e9e2fa
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Based on the STM32F10x driver. Removing old code as we need to use the
bus number when dealing with 4 possible peripherals.
Change-Id: Id0263aa008e9b039ff9a00339e5622e289ffdf99
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds support for the STMicroelectronics STM32F4x family in the
STM32 MCU line. Configuration is included for the STM32F401RE MCU.
Acknowledgements to Pawel Wodnicki's earlier submission from February that
was used as a starting point for this port. In the end, we rewrote all of it.
Change-Id: I9797c282ac3c0cc66a63b9d34821de95df537ef6
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Fix the error in thread rescheduling:
Fix Fast IRQ exit routine error when it reschedules threads if
(prio >= 0) || (sched_locked == 0) || (next_thread == _current),
while the correct condition for thread rescheduling is:
(prio >= 0) && (sched_locked == 0) && (next_thread != _current),
Fix regular IRQ error when the regular IRQ exit routine rescheduled
threads when (next_thread == _current) instead of
(next_thread != current).
Increased IDLE_STACK_SIZE for ARC architecture, to hold saved
registers.
Change-Id: I1d87a968e231e13822844b7564567e6ca310cde2
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
The mk64f12 provides RNGA hardware. Follow the implementation pattern
used by various other driver classes and enable the RANDOM KSDK shim
driver if the RANDOM driver is enabled.
Change-Id: I46bdf16cf1c48937011fb1b0e4c292615efd4c95
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
They were the same, standardize on the lowercase one.
Change-Id: I8bca080e45f3e0970697d4451e468b9081f96f5f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
SOC_TI_LM3S6965 and UART_STELLARIS are platform-specific, remove from
arch/arm/defconfig.
Change-Id: I3b37bc2ddfabb1da4e7538b5ab0e553fb2464584
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
STM32F4 requires the alternative function config to be set, so just
initialize that as part of the gpio configure call.
Change-Id: I33a4a8efec59c5ebe7dc3f3580f0dd2bf7ded7f4
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
The STM32F1 range all have the independent watchdog, enable the driver
by default if CONFIG_WATCHDOG is enabled.
Change-Id: I3869884dc51c56194367b46007c87f6cee699689
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
All M7 features common to M3/M4 are working. New features like Tightly
Coupled Memory (TCM) are not yet supported.
Change-Id: I5f7b292e70843aec415728f24c973bb003014f4b
Jira: ZEP-977
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
With this patch we introduce unified kernel support for NIOS II.
Not all test cases have been ported, but the following command
currently succeeds with 43/43 passing test cases:
$ sanitycheck --arch=nios2 -xKERNEL_TYPE=unified \
--tag=unified_capable
Issue: ZEP-934
Change-Id: Id8effa0369a6a22c4d0a789fa2a8e108af0e0786
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Existing code wasn't removing a thread from the kernel's list
of active threads if the thread terminated or aborted. (It did
remove it if the delayed starting of a thread was cancelled.)
Change-Id: Icc97917e33765696480d0e9bf31e882ef555d095
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Gets rid of unnecessary THREAD_MONITOR_INIT() macro, to be
consistent with the approach taken by _thread_monitor_exit().
Aligns x86 code with the approach used on other architectures.
Revises the associated comments and removes unnecessary
doxygen tags.
Change-Id: Ied1aebcd476afb82f61862b77264efb8a7dc66c9
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Renames _thread_exit() to _thread_monitoring_exit() to make
its purpose clearer. Revises the associated comments and
removes unnecessary doxygen tags.
Change-Id: I010a328d35d2d79d2a29b9d0b6c02097bb655989
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
The baudrate calculation present in set_baudrate() is
causing the UART to emit inital bytes incorrectly, for a
reason currently unknown, but directly related to the fact
that __aeabi_uldivmod is being invoked.
Since the nRF5x Product Specifications do not provide a
standard formula to calculate baudrates and instead list
a predefined set of divisor values, we opt here to use the
official values and remove the attempt at calculating them
manually.
Change-Id: Ic3ff42ea6d065e9a1d26a5350ce5bf5ad661160a
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Several platforms utilize a ihex image format. Rather than
duplicating the build bits in everyones makefile, pull it into the
toplevel makefile so we all share it.
Change-Id: I9097b06e7e386a69ce6ab4d4e4d56cc776adfec2
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- the interrupt (both regular and fast) now does not do rescheduling
if the current thread is a coop thread or if the scheduler is not locked
- the _nanokernel.flags cache of _current.flags is not used anymore
(could be a source of bugs) and is not needed in the scheduling algo
- there is no 'task' field in the _nanokernel anymore: scheduling routines
call _get_next_ready_thread instead
- the _nanokernel.fiber field is replaced by a more sophisticated
ready_q, based on the microkernel's priority-bitmap-based one
- thread initialization initializes new fields in the tcs, and does not
initialize obsolete ones
- nano_private includes nano_internal.h from the unified directory
- The FIBER, TASK and PREEMPTIBLE flags do not exist anymore: the thread
priority drives the behaviour
- the tcs uses a dlist for queuing in both ready and wait queues instead
of a custom singly-linked list
- other new fields in the tcs include a schedule-lock count, a
back-pointer to init data (when the task is static) and a pointer to
swap data, needed when a thread pending on _Swap() must be passed more
then just one value (e.g. k_stack_pop() needs an error code and data)
- the 'fiber' and 'task' fields of _nanokernel are replaced with an O(1)
ready queue (taken from the microkernel)
- fiberRtnValueSet() is aliased to _set_thread_return_value since it
also operates on preempt threads now
- _set_thread_return_value_with_data() sets the swap_data field in
addition to a return value from _Swap()
- convenience aliases are created for shorter names:
- _current is defined as _nanokernel.current
- _ready_q is defined as _nanokernel.ready_q
- _Swap() sets the threads's return code to -EAGAIN before swapping out
to prevent timeouts to have to set it (solves hard issues in some
kernel objects).
Change-Id: Ib9690173cbc36c36a9ec67e65590b40d758673de
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Still missing a working timer driver, as SysTick is not really available
in this SoC series (enabled to avoid build issues, but not used).
Jira: ZEP-784
Change-Id: Ie1c8e6c5e8955ee7f260ce013f4451f9215f3457
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Integrating the IRQ definitions for both nRF51 and nRF52, and defining
the set of IRQ values that are common to both.
Also switch the controller, uart and clock drivers to use the common
header definitions.
Change-Id: Id6816d7a97720896cfe4df83656fb8b1f8fb01fa
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Not disabling SysTick as it is optional by the spec.
SVC not used as there is no priority-based interrupt masking (only
PendSV is used).
Largely based on a previous work done by Euan Mutch <euan@abelon.com>.
Jira: ZEP-783
Change-Id: I38e29bfcf0624c1aea5f9fd7a74230faa1b59e8b
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
EM7D was recently merged, and one change suggested there was
to remove conditional checks for NSIM. It is OK to have the simulator
use the exact same memory addresses and sizes as would be found on the
board. This submission fixes EM9D and EM11D to be the same -- i.e.
to not have NSIM conditionals.
See ZEP-966.
Change-Id: Ia990ff7bb4b7ff5071af83723ed3d1420fdff012
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
The EM7D SOC is similar to EM11D, except it has different sized
iccm and dccm memories, and also has FIRQ with RGF_NUM_BANK==1.
To select this SOC on the board, all dip switches are in the up position.
See ZEP-966.
Change-Id: I864ffe0efdf367de0a8cd58e9c46efd7e401c671
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
For the EM Starterkit, one SOC I will soon be adding is EM7D.
This SOC has FIRQ, but only has one register bank.
Thus the interrupt handling for FIRQ needs to be different
when CONFIG_RGF_NUM_BANKS==1. The handler must instead push
registers onto the stack in the same stack frame layout that RIRQ uses.
This allows for context switch to be easily done since its compatible.
The common interrupt entry point _isr_enter must save r0 before using
it, because in the FIRQ 1-bank case, it would be destroyed otherwise.
So a global variable named saved_r0 has been added for this reason.
The stack cannot be used to save r0, because it first has to determine
whether its FIRQ or RIRQ here. This change has been tested on the
EM Starterkit with EM7D SOC changes -- coming soon. To make the review
easier, these 3 files are submitted first.
Also, exceptions will no longer use the _firq_stack.
This stack is not needed in the 1-bank case, but an exception stack
is needed. I've added a new stack called _exception_stack,
and made it be 512B, which should be enough for one exception.
See ZEP-966
Change-Id: I6f228b840da7c4db440dd1cfef4ae25336c87f0d
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Those options are not being used anywhere, so remove them and avoid some
confusion.
Change-Id: Ia3767dbd2432851dfae4b1e996f02ed1b2450505
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Bluetooth controller implementation requires the low power
oscillator for radio time space scheduling and as sleep
clock; the high frequency oscillator as the active clock.
For Nordic Semiconductor's nRF5 Series SoC's select the
NRF Clock peripheral when BLUETOOTH_CONTROLLER is selected
in Kconfig build.
Jira: ZEP-897
Change-id: I6f99e90b3485e757be61e91c749e485dd0cfdaba
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Provide a network driver wrapped around the KSDK ENET and PHY
drivers.
The driver performs one shot PHY setup. There is no support for PHY
disconnect, reconnect or configuration change. The PHY setup,
implement via KSDK contains polled code that can block the
initialization thread for a few seconds.
There is no statistics collection for either normal operation or error
behaviour.
Origin: Original
Change-Id: Ia0f2e89a61348ed949976070353e823c178fcb24
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
There is a convention in the soc implementation for other
(non-ethernet) classes of driver that enabling a generic driver has the
effect of enabling the specific flavour of driver required for the
board. Extend this convention such that when ETHERNET is enabled, the
quark_x1000 enables the DW ethernet driver.
Change-Id: I525471d259c9582024cd44d6cc4557260abe6451
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Build breaks when enabling CONFIG_NEWLIB_LIBC because it has its own
sched.h file.
This is a bad symptom of a greater issue: the build system passes many
'-I<path>' options to the compiler, and that allows including header
files by simply specifying their names (when located somewhere else than
<zephyr>/include/) and can cause clashes when several files in different
locations have the same name, like in this case.
Fixes ZEP-1062.
Change-Id: I81d1d69ee6669a609cd0c420b1b8f870d17dcb67
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Builtin might not be available for ARMv6 (Cortex-M0/M0+) depending on
the toolchain used (not available by Zephyr's SDK GCC), so move the
atomic operations selection to the Cortex-M family Kconfig file.
Change-Id: I20a5a0c5fdd2bcff2d304139f5a7e8502fdb1cb3
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
When adding a thread to the ready queue, it is often known at that time
if the thread added will be the next one to run or not. So, instead of
simply updating the ready queues and the bitmask, also cache what that
thread is, so that when the scheduler is invoked, it can simply fetch it
from there. This is only done if there is a thread in the cache, since
the way the cache is updated is by comparing the priorities of the
thread being added and the cached thread.
When a thread is removed from the ready queue, if it is currently the
cached thread, it is also removed from the cache. The cache is not
updated at this time, since this would be a preemptive fetching that
could be overriden before the newly cached thread would even be
scheduled in.
Finally, when a thread is scheduled in, it now becomes the cached thread
since the fact that it is running means that by definition it was the
next one to run.
Doing this can speed up considerably some context switch times,
especially when a thread is preempted by an interrupt and the same
thread is scheduled when the interrupt exits.
Change-Id: I6dc8391cfca566699bb9b217eafe6bc6a063c8bb
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The unified kernel calls a function (_get_next_ready_thread) to fetch
the next thread to run: it thus must save caller-saved registers that
are expected to hold a value before calling such function.
The callee-saved registers are available after saving them in the
outgoing thread's stack, so use some of those instead to reduce the
number of registers to save before calling _get_next_ready_thread. Also,
save caller-saved registers in callee-saved registers instead of on the
stack to reduce memory accesses.
This issue did not show up previously, probably because
_get_next_ready_thread did not use the regsiters that had to be saved,
but an upcoming optimization to that function stomps on them.
Change-Id: I27dcededace846e623c3870d907f0d4c464173bf
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The code density registers are NOT saved on the stack.
This is controlled by bit 13 in AUX_IRQ_CTRL, which didn't even have a symbol
defined for it. I've also added _ARC_V2_AUX_IRQ_CTRL_LP for bit 13.
Change-Id: Ie80853b72bed4e60a5cf1cf0a8c905a3d86180d9
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
In order to add the EM7D SOC, I will be implementing a version of the FIRQ
interrupt handler that saves and restores registers on the stack when
RGF_NUM_BANKS==1. All other ARC SOCs at this time have RGF_NUM_BANKS==2,
allowing for a faster handler that can use the registers in the 2nd register bank.
But EM7D doesn't have this 2nd bank, hence the need for this new configurable choice.
(See ZEP-966)
Change-Id: Ie089f1f079902552cf279c2cda23ee0805b01eed
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Using AON for GPIO kconfigs is very specifc to quark se, there
is no need to make this special for this platform. Use the
existing scheme instead.
Change-Id: I946431490380dc0f537d6056277a94c9c9c80fed
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Not used anymore as the support for dynamic IRQs was removed by
commit 844e212.
Change-Id: I624bbd777b2dbcbf905cedc61e63cef21e8a0bce
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Move SRAM_BASE_ADDRESS and FLASH_BASE_ADDRESS to Kconfig.soc since
it will most likely be the same values for all STM32 socs.
Change-Id: I682dc441e34155a19a4f90757707008ef299e9d4
Signed-off-by: Fabien Parent <fparent@baylibre.com>
i2c_quark_se_ss driver is deprecated and replaced
by i2c_qmsi_ss. So remove i2c_quark_se_ss definition.
Change-Id: Idcc6a7f01ffae626ae7d5f9966eac67be78599af
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
Simplified some documentation, removing inconsistencies and making
it easier to understand by separating PM infrastructure areas and
soc specific components that implement the hooks.
Removed the DEVICE_SUSPEND_ONLY policy as it is redundant and
causes high complexity in the flow. It is also not practical
to use it because it was meant to be used without doing CPU or SOC
low power state operations. This means it would do device PM
operations in the ISR of the system timer used by the scheduler.
This can disrupt the scheduler time.
Added a check of a flag around the notification sent from the ISR
of the wake event and created APIs to set/clear it. This will
allow disabling the notification when not needed from
_sys_soc_suspend().
Jira: ZEP-972
Change-Id: Id7aa7d2683384eabed518d4efac446ecc84c3498
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Exception stubs now just push the handler and in some cases a dummy
error code before jumping to the exception handling code, never to
return.
Change-Id: I6a79d9243deb3fc7ccdae003dd0917364c0aa304
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Interrupt stubs now just push the ISR and parameter onto the stack
and jump to the common interrupt code, never to return.
Change-Id: I82543d8148b5c7dfe116c43f41791f852614bb28
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Re-enabling interrupts before running the ISR must only be done
when CONFIG_NESTED_INTERRUPTS is turned on.
Change-Id: I2c04f2ce08d41cfef5553ee8554a90d1be0e86a3
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
commit e57b21c78c ("irq: Use lowest priority not a
hard-coded priority 2") introduce a wrong whitespace,
not complying with coding style. Remove it.
Change-Id: Ie7e48843e5da6cb3417773ef8a57cf9a166c70d6
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
In this file was found an assumption about how many
priorities are being used. This is configurable with
CONFIG_NUM_IRQ_PRIO_LEVELS, however, so it should be using that
instead. This line of code changes:
or r3,r3,(1<<(CONFIG_NUM_IRQ_PRIO_LEVELS-1))
so as to use the correct bit to OR.
Change-Id: I8c6297e98b5163aa27460a68b203e8a27d1e2506
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Set _ARC_V2_DEF_IRQ_LEVEL to the last legal priority value, and not 15.
The last legal value is: (CONFIG_NUM_IRQ_PRIO_LEVELS-1).
This is safer because we don't want priorites not configured to be
enabled.
Change-Id: I1689cc00aa7e707a204d16ec17d7f396566e8638
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
No need to create new Kconfig that do exactly the same, just
reuse those from the main QMSI driver.
Change-Id: I965055f36845ac0464e4a383b0d05c3ae35c0015
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The CPU manual indicates that 8-byte alignment is sufficient,
not sure why gdt_rom was aligned on a 16-byte boundary.
The null descriptor in the GDT is never looked at by the CPU,
save a few bytes by putting the 6-byte pseudo descriptor there.
Change-Id: I73f26cdeb30a91f8258c88ef960a45812a11d959
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This header has a bunch of data structure definitions and macros useful
for manipulating segment descriptors on X86. The old IDT_ENTRY defintion
is removed in favor of the new 'struct segment_descriptor' which can be
used for all segment descriptor types and not just IRQ gates.
We also add some inline helper functions for examining segment registers,
descriptor tables, and doing far jumps/calls.
Change-Id: I640879073afa9765d2a214c3fb3c3305fef94b5e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add _arch_irq_is_enabled external interrupt API to find out
if an IRQ is enabled.
Change-id: I8ccbaa6d4640c1ab8369d2d35c01a2cfbb02f6cd
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Do not clear pending IRQ when enabling an IRQ on ARM
architectures. Peripherals and S/W ISRs may be required to
be deferred until they are enabled later and the pended
IRQ should be retained for the ISR to be vectored to when
enabled.
Change-id: I808183018d8a2cc58390a1de3b4797b2bb7c6ec9
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The '_timeout' structure is needed by dummy threads so that they can
handle timeouts.
Change-Id: Iefabd6ad93c8e176e95ce4262f5f3544dc90b7d5
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Do not force selection of X86_IAMCU
Jira: ZEP-867
Change-Id: I2ca0bcd73502321e9e6f5a4638c309393da54e43
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Quoting the product specification this device contains an "ARM
Cortex-M4 processor with floating-point unit" or, as this would
more normally be expressed an ARM Cortex-M4F.
Update Kconfig accordingly.
Change-Id: I5bd6f17724d0d4aa9aaab9961f12d4e8502c38a5
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Unified kernel does not provide the _thread_arg_t type, but instead uses
void * directly for its thread entry parameters. _thread_entry_t is
typedefed from void * anyway, and only obfuscates the type. So, define
_thread_entry_t to be a function pointer to a function with three void *
parameters, and when the unified kernel becomes the only kernel, all the
_thread_arg_t types will go away.
With this change, IAMCU runs all the tests sysV x86 is able to run as a
unified kernel.
Change-Id: I53c8754629a5a0a114a16a775ff1efc1884496ff
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Provide a random driver wrapped around the KSDK RNGA driver.
Origin: Original
Change-Id: I43feeb37d8d5173c7b95af8e80434fb7dc77a83e
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The x86 architecture port is fitted with support for the unified kernel,
namely:
- the interrupt exit code now calls _Swap() if the current
thread is not a coop thread and if the scheduler is not locked
- there is no 'task' fields in the _nanokernel anymore: _Swap()
now calls _get_next_ready_thread instead
- the _nanokernel.fiber field is replaced by a more sophisticated
ready_q, based on the microkernel's priority-bitmap-based one
- nano_private includes nano_internal.h from the unified directory
- the FIBER, TASK and PREEMPTIBLE flags do not exist anymore: the thread
priority drives the behaviour
- the tcs uses a dlist for queuing in both ready and wait queues instead
of a custom singly-linked list
- other new fields in the tcs include a schedule-lock count, a
back-pointer to init data (when the task is static) and a pointer to
swap data, needed when a thread pending on _Swap() must be passed more
then just one value (e.g. k_stack_pop() needs an error code and data)
- fiberRtnValueSet() is aliased to _set_thread_return_value since it
also operates on preempt threads now
- _set_thread_return_value_with_data() sets the swap_data field in
addition to a return value from _Swap()
- convenience aliases are created for shorter names:
- _current is defined as _nanokernel.current
- _ready_q is defined as _nanokernel.ready_q
- _Swap() sets the threads's return code to -EAGAIN before swapping out
to prevent timeouts to have to set it (solves hard issues in some
kernel objects).
- Floating point support.
Note that, in _Swap(), the register holding the thread to be swapped in has
been changed from %ecx to %eax in both the legacy kernel and the unified kernel
to take advantage of the fact that the return value of _get_next_ready_thread()
is stored in %eax, and this avoids moving it to %ecx.
Work by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Allan Stephens <allan.stephens@windriver.com>
Benjamin Walsh <benjamin.walsh@windriver.com>
Change-Id: I4ce2bd47bcdc62034c669b5e889fc0f29480c43b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Loading the _nanokernel address in %edi rather than in %eax allows
calling funtions in _Swap() without having to restore it, since %eax is
used for the return value. %edi is a callee-saved register and does not
have to be restored.
Change-Id: I338086d8e15857e835d5d7487de975791926f869
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The ARM architecture port is fitted with support for the unified kernel,
namely:
- the interrupt/exception exit code now pends PendSV if the current
thread is not a coop thread and if the scheduler is not locked
- fiber_abort is replaced by k_thread_abort(), which takes a thread ID
as a parameter (i.e. does not only operate on the current thread)
- the _nanokernel.flags cache of _current.flags is not used anymore
(could be a source of bugs) and is not needed in the scheduling algo
- there is no 'task' field in the _nanokernel anymore: PendSV not calls
_get_next_ready_thread instead
- the _nanokernel.fiber field is replaced by a more sophisticated
ready_q, based on the microkernel's priority-bitmap-based one
- thread initialization initializes new fields in the tcs, and does not
initialize obsolete ones
- nano_private includes nano_internal.h from the unified directory
- The FIBER, TASK and PREEMPTIBLE flags do not exist anymore: the thread
priority drives the behaviour
- the tcs uses a dlist for queuing in both ready and wait queues instead
of a custom singly-linked list
- other new fields in the tcs include a schedule-lock count, a
back-pointer to init data (when the task is static) and a pointer to
swap data, needed when a thread pending on _Swap() must be passed more
then just one value (e.g. k_stack_pop() needs an error code and data)
- the 'fiber' and 'task' fields of _nanokernel are replaced with an O(1)
ready queue (taken from the microkernel)
- fiberRtnValueSet() is aliased to _set_thread_return_value since it
also operates on preempt threads now
- _set_thread_return_value_with_data() sets the swap_data field in
addition to a return value from _Swap()
- convenience aliases are created for shorter names:
- _current is defined as _nanokernel.current
- _ready_q is defined as _nanokernel.ready_q
- _Swap() sets the threads's return code to -EAGAIN before swapping out
to prevent timeouts to have to set it (solves hard issues in some
kernel objects).
Change-Id: I36c03c362bc2908dae064ec67e6b8469fc573983
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
They use data that is unavailable to the unified kernel, and are not
used anymore really. For now, only compile them when CONFIG_GDB_INFO=y,
and never enable CONFIG_GDB_INFO when building the unified kernel.
These files should go away when the unified kernel is made the only
kernel type.
Change-Id: I0a2a917dd453ecaae729125008756e0f676df16d
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Watchdog timer is enabled after the board reset. It is not used by Zephyr OS,
and having it enabled causes system resets during CPU-intensive operations.
Change-Id: If5583dbd2d2fb2206274467c523d6b5d147f1fbe
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Define symbolic constants for watchdog timer registers.
Provides the necessary interface to configure or disable
the watchdog timer.
Change-Id: I80002a843361569fdd78b725fc3f68e65195d02e
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
The ARC side should use the same console UART as x86 by default if we
want identical behavior.
Change-Id: I067860581cfd93d97ffad3d8f0bc5591f555e3ce
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
There is a total of 39 IRQs defined at nrf52/soc_irq.h.
Change-Id: Id478fb15a07cfdecaa6cc136730d20017b8752c5
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Quark D2000 and SE based boards (but Arduino 101) use QMSI bootloader
by default. QMSI bootloader sets up GDT in the so-called 'basic flat
model' just like Zephyr does by default.
This patch changes Quark D2000 and SE boards default configuration
so they rely on QMSI bootloader and we don't sets up GDT twice.
Change-Id: Ic6e520148b732bd48c00657c6c8138a8d865faef
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Zephyr uses the last priority level for the PendSV exception, but
sharing prio can still be useful on systems with a reduced set of
priorities, like Cortex-M0/M0+.
Change-Id: I767527419dcd8f67c2b406756b9208afd3b96de0
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
_irq_controller_isr_vector_get() now returns -1 if it couldn't
determine which vector was activated.
Issue: ZEP-602
Change-Id: Ib0f5dbc3b68cc5e2c3a23121530e178aede20d06
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Change the signal ramp up/down config parameters in i2c driver
module to SoC specific.
Jira: ZEP-753
Change-Id: Ie01f1d890a7133d30ea53eee07f60354734a8571
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Add a shim layer around the ksdk I2C driver to adapt it to the Zephyr
I2C interface. Currently only supports master mode.
Jira: ZEP-717
Change-Id: I704b8c38e22e456bb9fa4325682b2a354a27a7ba
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Since nrf.h abstracts the differences between the nRF51 and nRF52
architectures and chooses the right headers to include, it is
safer to use that instead of directly including the soc-specific
headers.
Jira: ZEP-702
Change-Id: I0e1758ede48f3422a41d226b0eab008e4ba2c77c
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Originally, x86 just supported APIC. Then later support
for the Mint Valley Interrupt Controller was added. This
controller is mostly similar to the APIC with some differences,
but was integrated in a somewhat hacked-up fashion.
Now we define irq_controller.h, which is a layer of abstraction
between the core arch code and the interrupt controller
implementation.
Contents of the API:
- Controllers with a fixed irq-to-vector mapping define
_IRQ_CONTROLLER_VECTOR_MAPPING(irq) to obtain a compile-time
map between the two.
- _irq_controller_program() notifies the interrupt controller
what vector will be used for a particular IRQ along with triggering
flags
- _irq_controller_isr_vector_get() reports the vector number of
the IRQ currently being serviced
- In assembly language domain, _irq_controller_eoi implements
EOI handling.
- Since triggering options can vary, some common defines for
triggering IRQ_TRIGGER_EDGE, IRQ_TRIGGER_LEVEL, IRQ_POLARITY_HIGH,
IRQ_POLARITY_LOW introduced.
Specific changes made:
- New Kconfig X86_FIXED_IRQ_MAPPING for those interrupt controllers
that have a fixed relationship between IRQ lines and IDT vectors.
- MVIC driver rewritten per the HAS instead of the tortuous methods
used to get it to behave like LOAPIC. We are no longer writing values
to reserved registers. Additional assertions added.
- Some cleanup in the loapic_timer driver to make the MVIC differences
clearer.
- Unused APIs removed, or folded into calling code when used just once.
- MVIC doesn't bother to write a -1 to the intList priority field since
it gets ignored anyway
Issue: ZEP-48
Change-Id: I071a477ea68c36e00c3d0653ce74b3583454154d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Treat the sensor subsystem as an independent board that can send
messages to UART and disable IPM and the messaging interface. IPM
can be enabled by applications that require such interface.
Fix all samples that are affected by this change to make sanitycheck
pass.
Jira: ZEP-451
Change-Id: I3df6af16adefaefec02b97778d6c68ffc920ac35
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The ksdk provides a clock driver, fsl_clock.c, for the K64F and an
example usage of that driver, clock_config.c, for the Freedom board.
See ext/hal/ksdk/devices/MK64F12/
Leverage parts of clock_config.c to configure the clocks (specifically,
the sequence in BOARD_BootClockRUN()), but use the new Kconfig options
to set up the configuration structure. This will allow support for new
boards that may have a different external oscillator frequency or type.
Jira: ZEP-715
Change-Id: I3f0c75e6236f57600cd8b7f06f4482b13026fc10
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Many Kinetis SoCs contain an Oscillator (OSC) module and a Multipurpose
Clock Generator (MCG) module to configure clocks. Adding options to
configure these modules for PLL operation with different external
oscillator frequencies, which can vary across boards. More options may
be added later to support other clocking modes such as FLL.
Jira: ZEP-715
Change-Id: Ia121cc5b464d7e681883507bd756d331a8abd6ef
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The toolchain headers included an abstraction for defining symbol
names in assembly context in the situation where we're using a
DOS-style assembler that automatically prepends an underscore to
symbol names.
We aren't. Zephyr is an ELF platform. None of our toolchains do
this. Nothing sets the "TOOL_PREPENDS_UNDERSCORE" macro from within
the project, and it surely isn't an industry standard. Yank it out.
Now we can write assembler labels in natural syntax, and a few other
things fall out to simplify too.
(NOTE: these headers contain assembly code and will fail checkpatch.
That is an expected false positive.)
Change-Id: Ic89e74422b52fe50b3b7306a0347d7a560259581
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
These files were almost exactly the same and had already started
bit-rotting (note the missing net_l2 section in linker_harvard.ld)
Issue: ZEP-528
Change-Id: I5039a2c1b86c5764a361b268c33ae8b17da1a9e0
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Defined in all SoCs, but never referenced anywhere. That definition has
been replaced by CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC.
Change-Id: I1801f72a03925717ded6fbfdef22b1993f843461
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Completing the terminology change started with change 4008
by updating the Kconfig files processed to produce the
online documentation, plus header files processed by
doxygen. References to 'platform' are change to 'board'
Change-Id: Id0ed3dc1439a0ea0a4bd19d4904889cf79bec33e
Jira: ZEP-534
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
A previous re-work of IRQ priorities was led astray by an incorrect
comment. Priority level 1 is not a non-maskable interrupt priority.
In addition, zero latency IRQs are not implemented on ARC.
Timer driver now doesn't specify IRQ_ZERO_LATENCY (as that wouldn't be
correct) and its IRQ priority is now tunable in Kconfig. The default is 0.
IPM driver on both ARC and x86 side were being configured with hard-coded
priority of 2, which wasn't valid for ARC and caused an assertion failure.
The priority level is now tunable with Kconfig and defaults to 1 for ARC.
Issue: ZEP-693
Change-Id: If76dbfee214be7630d787be0bce4549a1ecbcb5b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
0 should be fine; no need to make this an FIRQ or non-maskable
Change-Id: Ifdf89a72e4864a2c2bbd83752cd814e2cb9aa16e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The GPIO and UART drivers were failing to build due to some
missing soc.h defines.
Change-Id: I6811e3699449da0a61ccc8376a8e11b96ad7a4e5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add a Kconfig option to select between the Hard and Soft Float ABIs. We
also default to the Hard Float ABI as this is what older SDK versions
supported.
JIRA: ZEP-555
Change-Id: I2180c98cd7556ab49f5ca9b46b31add2c11bd07b
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
QMSI boot loader uses GPS0. power.c should use GPS1 for its
purpose because GPS1 is reserved for PM use. Switched to
use GPS1 instead.
Jira: ZEP-647
Change-Id: I653450cd0b42aa80bef21c8a42f4aa39cdaef2ed
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
The K64F SoC initialization previously used macros and structs
custom-defined in Zephyr in order to access peripheral registers.
Refactored it to use CMSIS-style register accesses from the ksdk
instead.
Change-Id: I80975c62de07ec95cf830e99cd5b0abb9623acd0
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The boot initialization and boot process of the sensor sub systems
is now using the new system log macros and updated the Kconfig
variable to be a level rather than a bool.
Change-Id: I098143684f8e7077a525e7fcbc93b42b22d427ac
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Reflects RAM increase that we get with SDK 0.8.2.
Change-Id: I5d7157834e29bb56864e81fedfb9766d5e4a24f8
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Previously, exception stubs had to be declared in assembly
language files. Now we have two new APIs to regsiter exception
handlers at C toplevel:
_EXCEPTION_CONNECT_CODE(handler, vector)
_EXCEPTION_CONNECT_NOCODE(handler, vector)
For x86 exceptions that do and do not push error codes onto
the stack respectively.
In addition, it's now no longer necessary to #define around
exception registration. We now use .gnu.linkonce magic such that
the first _EXCEPTION_CONNECT_*() that the linker finds is used
for the specified vector. Applications are free to install their
own exception handlers which will take precedence over default
handlers such as installed by arch/x86/core/fatal.c
Some Makefiles have been adjusted so that the default exception
handlers in arch/x86/core/fatal.c are linked last. The code has
been tested that the right order of precedence is taken for
exceptions overridden in the floating point, gdb debug, or
application code. The asm SYS_NANO_CPU_EXC_CONNECT API has been
removed; it was ill- conceived as it only worked for exceptions
that didn't push error codes. All the asm NANO_CPU_EXC_CONNECT_*
APIs are gone as well in favor of the new _EXCEPTION_CONNNECT_*()
APIs.
CONFIG_EXCEPTION_DEBUG no longer needs to be disabled for test
cases that define their own exception handlers.
Issue: ZEP-203
Change-Id: I782e0143fba832d18cdf4daaa7e47820595fe041
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
CONFIG_SOC_GENERIC_ARC doesn't exist so remove it.
Change-Id: Idecfd27684b5fd83b7b296daa46a1a21a0ae4d95
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We have already done this on x86 and ARM. The policy is as follows:
* IRQ priority levels starting at 0 all have the same semantics and
do not have special properties. The priority level is either ignored
on arches which do not support programmable priority levels, or lower
priority levels take precedence over higher ones.
* Special-case priorty levels are specified via flags, in which case
the supplied priority level is ignored.
Issue: ZEP-60
Change-Id: Ic603f49299ee1426fb9350ca29d0b8ef96a1d53a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Created set of functions that was designed in the original RFC to
contain arch and soc specific code. This makes the interface to
the OS PM infrastructure cleaner and makes it easier to understand
the flow in the sample app. Also it makes code reuse easier across
soc/arch implementations. These are open to change in future if
other means to achieve the same goals are in place.
Jira: ZEP-227 ZEP-225
Change-Id: Ief57871c370341c55009ad4f456b7f71f2c2a3c6
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
The interrupt stack wasn't being initialized at boot.
Change-Id: Iec3e770d385643415641e15906c3a53f7c74a2e9
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Utilize the gcc -print-libgcc-file-name to determine the path to
libgcc.a. Using this also resolve issues if we are building with
floating point and the various ABIs to pickup the right lib.
We can also simply a few Makefiles and remove the need to export
_CROSS_COMPILE_arm_isa.
Change-Id: I293394c921c18fa4984173ba51825d6f9a333697
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Until now, EOI had always been sent out to the APIC with interrupts
unlocked. Depending on timing, there is a race where the next interrupt
on the same line could arrive before _IntExit disables interrupts
and pops context. If this happens consecutively enough times, the
interrupt stack will overflow.
Now we disable interrupts at the beginning of _IntExitWithEoi and they
remain that way until 'iret'.
Change-Id: Ibb28e0db902ff483d7a885389f231ac2d1864657
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Arches now select whether they want to use the GCC built-ins,
their own assembly implementation, or the generic C code.
At the moment, the SDK compilers only support builtins for ARM
and X86. ZEP-557 opened to investigate further.
Change-Id: I53e411b4967d87f737338379bd482bd653f19422
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This is at the expense of code size. The QEMU and MAX10
targets have plenty of space so enable it for these boards,
but leave off by default for others.
Change-Id: I93fdb7db14232727e9953b22490d8869ff3b60e7
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The comments for INT_ACTIVE and EXC_ACTIVE now refer to
"executing context ..." for all architectures.
Change-Id: Ib868958639a3b30e1814fcaa4d1f0651d3b2561e
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
When CONFIG_SYS_POWER_DEEP_SLEEP is enabled, the _sys_soc_resume
function is called and the 'ZF' bit from EFLAGS register may be set
to 1. In that case, we end up wrongly jumping into 'copyDataDone'
label and no data is copied from ROM to RAM.
It seems this 'je' instruction is used without any previous comparison
operation which properly sets the ZF flag. Since 'ZF' initial value is
0, we never jump into 'copyDataDone' label. Also, this 'je' instruction
doesn't seem to be really required since, if %ecx is zero, no data will
be copied anyway.
That being said, this patch removes the 'je' instruction since it fixes
the bug described in the first paragraph and it doesn't affect the rest
of the crt0 execution.
Also, removes outdated information about section size and alignment.
Change-Id: Ia062b78247c4059009193a53f879aa1ebe80881d
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Iván Briano <ivan.briano@intel.com>
The 16550 will now be the default console device.
Change-Id: I92a6b49984b055e7d5f5c97e5192150be0d5c5c7
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We are not using this core build any more. Users should be using
the provided F core instead.
Change-Id: I2b5266273030c1bd355aafa78733b4077848d115
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This patch basically reverts patch "QMSI/uart: Use IOAPIC_EDGE instead
of IOAPIC_LEVEL". The issue with lost UART interrupts is fixed with
following patch: "_loapic_isr_vector_get: fix implementation" which is
a proper way.
Change-Id: I07aa168335827b09db7fcb2486b01585648ff5d6
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Some issues have been noted with nested interrupts on quark SE.
In particular, the wrong vector # being sent to the IOAPIC EOI
register. Now when doing EOI, we lock interrupts so that the act
of reading the current vector being serviced, and sending EOI
to both controllers happens atomically.
Change-Id: Id9ad992740e197bb9d4638764952b04a27c4af61
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The '_sys_soc_resume' symbol is function-type not data-type as declared
in crt0.S. This patch fixes this by using GTEXT macro instead.
Change-Id: Ibe8bcf92ab045bfe908fd2048d046083e773894f
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
The code expected r10 to be preserved across the call to the
event logger, which wasn't reasonable given that it is caller-
saved.
Change-Id: I694357ea7ee9b410b93b5a0894e8c38c53127363
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Having two parallel implementations is a maintenance issue, especially
when some strategically placed #ifdefs will suffice.
We prefer the ASM versions for SYS V, as we need complete control of
the emitted assembly for interrupt handling and context switching.
The SYS V code is far more mature. IAMCU C code has known issues with
-fomit-frame-pointer.
The only difference between the two calling conventions is that the
first three function arguments are provided in eax, edx, ecx instead
of on the stack.
Issue: ZEP-49
Change-Id: I9245e4b0ffbeb6d890a4f08bc8a3a49faa6d8e7b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Since we started to use UART_IRQ_FLAGS define them also for
quark_d2000 board. Note that we use IOAPIC_LEVEL since this is right
thing to do and the issue with lost interrupts is fixed in
_loapic_isr_vector_get().
Change-Id: Iaed0283bcc01290e420b42ff5d40ce9d99bfc677
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Use IOAPIC_EDGE instead of IOAPIC_LEVEL to fix missing interrupts.
During tests it was found that using IOAPIC_LEVEL interrupts for UART at
some points are lost.
Proposed by Calando, Antoine <antoine.calando@intel.com>
Change-Id: I18b20217c4d73fdeaa424bf59d00f6be1ec6ef1b
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The emulator supports all the integer math instructions and has
the necessary registers for exception debugging.
Change-Id: I55938d9e3a4b9d219f6fee06fe070e860ca71d4b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
These are necessary to edit the CPU design in QSYS.
These originate from the F core archive supplied by Altera.
Change-Id: Ic03bd8738ae58dc154b5eaef91154fadaa61c491
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This build has support for hardware break/watch points.
Change-Id: Icf8a0d4abc82640eedd8c43322ebecf0ef069974
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We no longer assume pointer sizes are the same between host and
target, and use stdint defintions to size things.
Change-Id: Ie4dc41c60d62931fdb3d1764ade01c16a64d0b54
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Used by ARC, ARM, Nios II. x86 has alternate code done in assembly.
Linker scripts had some alarming comments about data/BSS overlap,
but the beginning of BSS is aligned so this can't happen even if
the end of data isn't.
The common code doesn't use fake pointer values for the number of
words in these sections, don't compute or export them.
Change-Id: I4291c2a6d0222d0a3e95c140deae7539ebab3cc3
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We now allow use of -mgpopt=global and -mgpopt=data. The 'global'
option is now the default instead of compiler-default local, expanding
global pointer usage to all small data in the system.
For systems where all RAM is less than 64K, the 'data' option may be
appropriate.
Some fixes had to be made to the system in order to get around some
issues:
* prep_c.c no longer uses fake linker variables to figure out the size
of data or BSS, as these gave the linker fits as it tried to compute
relative addresses to them.
* _k_task_ptr_idle is create by sysgen and placed in a special section.
Any small data in a special section needs to be declared extern
with __attribute__((section)) else the compiler will assume it's in
.sdata.
* same situation with extern references to k_pipe_t (fixed pipe_priv
test)
For legacy applications being ported to Nios II which do things that
freak out global pointer calculation, it can be disabled entirely.
Change-Id: I5eb86ee8aefb8e2fac49c5cdd104ee19cea23f6f
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
needs to be 0x8000 after .sdata and .sbss sections since
register offsets are 16-bit signed values.
Change-Id: Ia7486d32af81e54a6ebac6be7ec308dfdeafe79e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Adds Kconfig options CPU_HAS_FPU, FLOAT and FP_SHARING for the arm
architecture.
NOTE: All SOCs in the MK64F12 family have an FPU so that makes it a
convenient location to enable the hidden CPU_HAS_FPU option.
Change-Id: I71771d24f20f52079314bb8db9bf8a0aa827ab41
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Apply the correct compiler options when building for a Cortex-M4
processor that has floating point enabled. Using 'softfp' allows
floating point to be used with existing libraries supplied by the
Zephyr SDK. The 'hard' option would require new libraries to be
shipped with the SDK.
Change-Id: I141c20f54c2241134510888688637930c7b560a2
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The caches get initialized on boot and flushed after XIP copy
takes place.
Change-Id: I642a14232835a0cf41e007860f5cdb8a2ade1f50
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Use all available ram, cut in half for simulated RAM/ROM
regions. Some larger test cases did not fit in 64K for
non-XIP case.
Change-Id: I12296286ca7efa5bcc1ceef30486c3fe8976811c
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Interrupts and context switches are logged. Since this CPU does not
have a power-saving instruction, it never enters a sleep state so
we do not call _sys_k_event_logger_enter_sleep() from anywhere.
Change-Id: Idcef388e93ffea373446997a0f87e93a4db44331
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Interrupts must always be unlocked when coming out of this function
or execution will never leave _power_save() once entered.
Change-Id: Idda9d9be7cfc576a1072afec38000f63ae262a10
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Quark SE USB device (Designware IP) controller driver implements
the low level control routines to deal directly with the hardware.
Only FIFO mode supported.
Change-Id: I086186df017734579f0363ed79effc1481ff32c2
Signed-off-by: Adrian Bradianu <adrian.bradianu@windriver.com>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Enable floating point in the Cortex-M4 processor.
Change-Id: Ibadae12b9197d6486fd5c6a3d4e177fa9e1c71bc
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Saves and loads the non-volatile FP registers (s16-s31) when switching
between threads.
Change-Id: Ib3190452d9a70d722032ac83176eb4fbb92aca3d
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Adds the preemptive floating point registers to the ARM's thread
control structure.
Change-Id: I65fbee6303091ce0658bbc442c4707d306b68e92
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Updates the exception stack frame structure to include floating point
registers.
Change-Id: I0fef784cf4d91dda245180abd75bfd9221825fba
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
at91sam3 supposed to go to Sleep mode and stop the CPU clock
(HCLK). It leads to JTAG problems. In order to be able to use
JTAG, we need to keep CPU clock on. This is achieved by
switching to Wait mode and keeping external main clock.
Since Wait mode switches off automatically Fast RC Oscillator,
but keeps external clock untouched.
Change-Id: Ife37a7691c3cbdf434e560725a71d419adafe054
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
We are not going to handle unimplemented math instruction
exceptions at runtime. Remove remaining comments and exports
related to this. We don't need to leave a gap in the exception
stack frame for it either.
Change-Id: I4f1f3980a0e43bbf6f2f7488a9182f7acb06be05
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Before we were hard-coding them in the assembly file. Makes it
easier to alter the layout of the struct.
Change-Id: I619dc67c68ff87fe60de429a69b2f604292d270c
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The faulting instruction was off by 4 bytes and we weren't printing
the exception cause code properly.
Change-Id: I86f4320c7be43dca96940186def56aa5e47bc49f
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We want to pass along the stack pointer, not dereference it.
Change-Id: I554eff316bffe50654942746e7960b561abb413b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Pulled from the ARC implementation. Tested via
test_obj_tracing.
Change-Id: I858e89cc9187f99539b362ade8098b3606d31464
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The extra and redundant -serial was casuing issues, remove.
Pass -nographic to work around issues with the experimental QEMU
builds.
Change-Id: I3102fe026a56781d5c4fb20acaa519af368f8a41
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Unnecessary and generates build errors for microkernel.
Change-Id: I678f44aa2b68c8f8954c78e7828e534f0c1f4215
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
It's all RAM, but we pretend the range 0x410000 - 0x420000
is the "ROM" region, and stuff gets copied into RAM starting
at 0x400000.
Change-Id: Idf6bd603e2552593f588cf6130ee4da946bcf5a3
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Nios II CPUs vary in configuration on whether they support
'mul', 'mulx', and 'div' family of instructions. The compiler
can be told to use GCC integer library routines instead if
needed.
Ideally we would just pull the configuration out of system.h,
but pulling include file #defines into the Make environment
will involve some build system work that is best left to a
later improvement.
We've decided to take this build-time approach rather than
handle unimplemented instruction exceptions, so remove the
hook in exception.S
Change-Id: I05be0d5ed4c1a49b23dca1550ee66fd5891044d2
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
If the CPU lacks certain features the only writable bit in the
status register is the PIE bit, so just write the saved value back.
Change-Id: I91537ff640aa9977d19587c4b0ae414028752341
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
No longer necessary as all the stubs which didn't use their
parameters have now been implemented.
Change-Id: I0ab3f024431426fbdac6d17de21e9c7338879f6e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The return value of _Swap() is often treated as a "don't care" value and thus
often ignored. However, there are cases when it is desirable to have a
meaningful return value. This meaningful value can be assigned via
fiberRtnValueSet(). To that end, a new field has been added to the coop
register struct to store this value for when _Swap() needs to return that
meaningful value.
Change-Id: Ic4967fa7d602850c09ebde18e8bfd4c97cda9ec8
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
For this implementation, the presence of a value in global
_offload_routine signifies to the exception code that we should
enter the IRQ handling code even if there are no bits enabled
in ipending. The 'trap' instruction gets us into the exception
handling code.
Change-Id: Iac96adba0eaf24b54ac28678a31c26517867a4d2
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We check to see if the stack pointer is somwhere on the
interrupt stack.
Change-Id: Ic9d21e9f03476b9c8955c44cbfa2e61dd1daed22
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Required by microkernel, currently does nothing.
Change-Id: I256886e3a52817d9216599bbf5691bc27c1d0ad8
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Per Altera these files for the /F core are freely distributable.
README included with instructions and links to necessary software.
Origin: Altera
Change-Id: I58c0dbcb5a2b11f0845d4e390e6aa0020d8b3ed5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This is a workaround until we can modify the kernel to pull this
value out of system.h instead of Kconfig.
Change-Id: Iaafa9003d2bbcb5b38a050c371466a206f716ae7
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Supports Internal Interrupt Controller only for now; EIC
supoort tracked in ZEP-258.
Change-Id: I2d9c5180e61c06b377fce4bda8a59042b68d58f2
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
With this code we can successfully boot and context switch into
the main thread. Nanokernel hello_world has the expected
"Hello World!" string in the RAM console.
Change-Id: I56335d992f5a7cbb12d9e4c02d1cc23ea28ae6ef
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
If XIP is turned on, only hardware breakpoints may be used, and
code cannot be loaded onto the device with nios2-download
or GDB 'load' command. RAM-constrained applications are free to
enable this if they need to.
Change-Id: Iee2d41f71f7ca2bc599801cf3cf0fac680273e51
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
When an image is sent over the wire with the GDB 'load' command,
it tries to start execution from the __start symbol, which needs to
be in RAM. Since the reset vector is in ROM, name it something else.
Change-Id: Id0bbfa76db9a8a81bd7ff20be3f2baec81eae15e
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Kconfig doesn't enforce any kind of alignment when specifying the
ISR stack size. Perform the assembly equivalent of STACK_ROUND_DOWN.
Change-Id: Ib7fb72ff7db8a3aa20ec6d0c59a03aa8227f6671
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
CONFIG_INIT_STACKS should initialize all stack regions
with 0xaa. Make sure the initial interrupt stack gets this
as well. Take care not to exceed the bounds of the array
if it is not 4-byte aligned.
Change-Id: Ib23329ac84a5a8515272be2944f948e8faba65b3
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This core has extra debugging features useful for this bring-up
exercise.
Change-Id: I619bc8768acb1d9be8699a6e238168f47e605f3d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add hidden configuration HAS_KSDK for SoCs to select if they have
support in the ksdk.
Change-Id: Ia4cd11901bc26d21a3bdfad6236d66656bb292cb
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use a kbuild trick to force built-in.o to get built even if there isn't
any code so we can link properly. This is cleaner than keeping around
empty files that don't do anything.
Change-Id: I4214d21104fe5f49613fa5697c8116b0e8c8aa50
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There was a reference to SOC_FAMILY_NRF5 which was not use by anyone
else and it seemes like it was a typo, where the right reference was
to symbol SOC_NRF5. However, the right fix is to move both sites to
use SOC_FAMILY_NRF5 *and* fix the SOC_SERIES to be only nrf52,
otherwise it causes path duplication and the build fails.
This was also causing documentation warnings that are thus killed.
Change-Id: I92e74a6158f02df43e6e857df8f1e67bcfdd9551
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Change the LOAPIC timer IRQ number to 10. It should not
be 0.
Change-Id: I156286d0e3b903cca07cc3f87804b145aacaf117
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
The ReST parser dislikes enumerations with no empty lines in
between. Whatever.
Change-Id: I480c08fe5b69f0d0f3ebfacdc64fc9e3ec94da21
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
No code uses it and it being undefined anywhere generates a
documentation warning.
Change-Id: I09de2e58edf82e7fb9780a5dea98a282502436b6
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
The KSDK device header files require a preprocessor macro that defines
the part number string (e.g., MK64FN1M0VMD12). Create a hidden Kconfig
option to hold the part number string, and hidden Kconfig options that
the board Kconfig will use to select the specific part number.
Change-Id: I612e785026261e425b47b5b7fae0c65b4f94b30b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get these out of system.h instead. A clause in libc-hooks.c
for newlib added since we don't get RAM size from
CONFIG_SRAM_BASE_ADDRESS.
Change-Id: Ic35113395b951f625e8e29658afe19c525037964
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We will require 6 variables to be defined by SOC-specific
linker script; these values in turn can be pulled from
defines in layout.h.
To help position code correctly we define two new ELF sections
for this arch, 'reset' and 'exceptions'.
Change-Id: Idffbd53895945b7d0ec0aac281e5bf7c85b4b2c2
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Nios II does not have a power saving instruction, so there is nothing
to really do here other than ensure that interrupts are in the correct
state when leaving nano_cpu_atomic_idle().
Change-Id: I664c7542dc2fc1795a453d35e183a737dcb20c38
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
For the moment, NIOS2_CPU_SOF must be set with the path to the
CPU configuration. We are checking with Altera on whether we
can directly check in the binary to the source tree.
These scripts depend on tools provided by the Altera Quartus
Prime Lite Edition. This is available for free but requires
registration on Altera's website to obtain.
Change-Id: Ia6cb6c9e43c3e141807a887cb25c47b370a7d8e9
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Altera tools for creating .pof files for flashing onto their
FPGAs require UFM data to be in this special format. Extend
the current 'all' and 'zephyr' targets to additionally create
this .hex file using objcopy, with the same exclusions as the
existing rule for .bin files.
Change-Id: I75293fba47536545359f817a1f2c1ae905b9d25c
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
__start is the CPU's reset vector. In a typical Nios II configuration,
the exception vector is 0x20 bytes after the reset vector, severely
constraining the amount of code that can go in here.
Split this into __start and __text_start. The only thing that __start
really need to do is init the instruction cache and jump into
__text_start.
JIRA IDs placed in comments for missing items.
Change-Id: I3c6b8ed65e8fcf6b6a735b80cf007d0180599230
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Linker scripts for Nios II will also need these headers as it
specifies the device's physical layout and various important
vector addresses.
Change-Id: Ie9efaf19e53d2493eed7b9783052393d7ea9dd0f
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Include nrf.h instead of directly using the specific header
required. This will be useful in the future when additional
Nordic ICs are supported.
JIRA: ZEP-377
Change-Id: I7a7257b0aaa5fa0a0d202322c366efbdd1d84458
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Translate CONFIG_SOC_SERIES_NRF52X to NRF52, which is the macro
expected by the Nordic MDK headers.
JIRA: ZEP-377
Change-Id: Ic846e4cddf8146ae9d96bc98d4b12311552dc4f6
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
There are a few problems with the code being repaired here.
1. A seti was used to re-enable all interrupts, even though the
thread being switched to may have had certain interrupt priorities masked.
2. saved status32 already has SC bit if thats wanted, so its ok to just
restore status32 as-is w/o needing to and off anything.
3. the code is difficult to write using kflag and seti because as you
restore registers, there aren't any to use. But we can exploit a
trick where we pretend an interrupt has occured by setting a bit in
AUX_IRQ_ACT, and then use RTIE instruction to restore status32
atomically with branching to return address. Something about the way
this code was written was causing stack corruptings and crashes in an
application that uses a high rate of both FIRQ and Regular interrupts.
Change-Id: Ia7166d51f0e750c07832ab115b7151ce37ee0278
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Since firq utilizes a 2nd register bank, and since all of those
many GPRs can be used, the strategy here is to save extra registers,
such as lp_count, lp_start, lp_end into callee saved registers.
These registers are safe to use because the C-ABI followed by the
compiler will cause these to be spilled to the stack if a C function
wants to use them. By selecting upper GPRs, r23-r25, it is very unlikely
the compiler will spill them. This improvement, therefore, can avoid a
d-cache miss since we are avoding memory altogether when saving these.
The struct firq_regs is no longer needed.
Change-Id: I7c0d061908a90376da7a0101b62e804647a20443
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Generate kernel image in Intel Hex format when building for the nRF52.
Remove the additional step from the board doc file.
Change-Id: I619496f64037c2a0ac459ae05e549e01458e0f71
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
It was found that the test latency_measure, when compiled
for microkernel, would fail on the ARC. This because the
trap handler, used by irq_offload, wasn't supporting thread switching.
This submission adds the code to do that, and the code size is
bigger only when CONFIG_MICROKERNEL is defined.
To keep code a bit smaller, there is a trick exploited here where
the AE bit is cleared in the STATUS32 register and in AUX_IRQ_ACT,
bit 1 is set, to make it appear as if the machine has interrupted
at priority 1 level. It then can jump into some common interrupt
exit code for regular interrupts and perform an RTIE instruction
to switch into the new thread.
test/latency_measure/microkernel now passes.
Change-Id: I1872a80bb09a259814540567f51721203201679a
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Moved setting of specific Cortex-M compiler flags in each SoC directory
unify setting them in the arch/arm/soc Makefile.
Add flags for Cortex M0, M0+, M1, M3, M4, and M7. However only
CONFIG_CPU_CORTEX_M3 and CONFIG_CPU_CORTEX_M4 are supported at this time
As part of this change converted Kbuild files for some SoCs into
Makefiles as the Makefiles would be empty otherwise.
Change-Id: Ie4e0178b141ca761ec482a610ae50e94fe58070f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>