- The gpio dt-bindings were not included
- gpio-controller property was not present in gpio nodes
- number of gpio cells was not present in gpio nodes
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
- The gpio dt-bindings were not included
- gpio-controller property was not present in gpio nodes
- number of gpio cells was not present in gpio nodes
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add DT node for EXTI (External Interrupt Controller). Only line
interrupts added for now (used for GPIO interrupts).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add DT node for EXTI (External Interrupt Controller). Only line
interrupts added for now (used for GPIO interrupts).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Now in Zephyr only stm32f7 processors have by default provided support
for QSPI IP block.
The same IP block is also available in stm32h7 (with different offsets),
so proper DTS description shall be provided as well for it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
In npcx_itim_evt_isr, it updates the cyc_sys_announced variable and
then calls sys_clock_announce() to update the kernel curr_tick variable.
If an ISR handler with higher priority preempts the timer ISR after the
sys_clock_announce is updated and before the sys_clock_announce() is
called, it will read the wrong time when calling k_uptime_get() because
the cyc_sys_announced and the curr_tick are not synchronized.
The commit fixes the problem by raising the timer's interrupt priority
to the highest one (i.e. 1 in npcx's configuration).
This commit also moves the computation of the delta cycle inside the
spinlock in sys_clock_elapsed() to prevent another potential racing
condition.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Some STM32 series need to configure health test register
for proper RNG behavior.
In addition, some also require to write a Magic number
before writing the configuration.
Note: on stm32h7 not all product lines support this configuration.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
As Nordic SPI, I2C and UART buses can act as both slave and master,
these nodes can have different compatible properties, and are annotated
with a comment, instead of a compatible property. This forces boards to
put compatible properties in their definitions, which is unnecessary
boilerplate for most boards, as most boards acts as masters on these
buses.
Set master mode by default for these buses, to reduce boilerplate and
potential errors in board definitions. Boards that need to act as slave
nodes will just continue to override the compatible properties.
Likewise, existing boards that override this compatible property with a
master binding will not be affected by this change.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
The stm32u5 device has a single iwdg node entry and label
without any need for interrupt. Even if it exists the irq entry
is not required.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Remove the requirement for specifying #address-cells and #size-cells
properties for CAN controller devicetree nodes.
CAN controllers do not have a common concept of devicetree child nodes
and thus have no need for these properties. This is in line with
upstream Linux kernel devicetree bindings.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
NPCX series used npcx-lvol-ctrl-map to record the GPIO & low voltage
control register map. However, GPIOE3 was configured as GPIOE6, which
is a non-existed pin. This commit fixes the GPIOE3 low voltage control
map.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
RT11xx can peripheral had incorrect clocking configuration in SOC clock
init code and DTS. Fix peripheral configuration.
Fixes#41251
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add board support for NXP i.MX8M Plus EVK. This board has the following
features:
Processor : i.MX8M Plus Quad applications processor
Memory : 32-bit LPDDR4 w/6 GB
eMMC 5.0/5.1 w/32 GB
SD/MMC connector
QSPI w/32 MB
Connectivity : MIMO 2x2 Wi-Fi 802.11b/g/n/ac and BT 4.2
2x Ethernet (1x w/ TSN)
PCIe M.2
2x CAN FD DB9 Female connectors
USB : USB 3.0 Type C for Power
USB 3.0 Type A
USB 3.0 Type C
Debug : JTAG connector
MicroUSB for debug console
More information about this board can be found in NXP website: https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/evaluation-kit-for-the-i-mx-8m-plus-applications-processor:8MPLUSLPD4-EVK
Signed-off-by: Chris Trowbridge <chris.trowbridge@lairdconnect.com>
When building for an STM32K010xB MCU, there is a deprecated properties
warning, which should be fixed by this PR.
Signed-off-by: Wouter Cappelle <wouter.cappelle@crodeon.com>
PSL_IN pin select register is Vsby power-up reset. When the other
core-domain-reset reset the chip, PSL_IN3/4 don't set to GPIO. This
commit adds PSL_IN3/4 to the pin select list in NPCX devicetree. So
these pins can be set to GPIO when the other core-domain-reset.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
GPT base address in the devicetree for the RT11xx SOC series was
incorrect, this commit fixes it
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added a driver to enable the GPT timer on RT1xxx parts to be used
instead of systick as a clock source. The timer is set to run in reset
mode, and uses the low frequency 32kHz oscillator for power savings
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Include the mem-region bindings for the stm32 ccm nodes and set the name
in the current dtsi files.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Enable flexspi for RT11xx SOCs. This requires selecting the correct
KConfig symbol for the cortex m4 and m7 SOCs, as well as correcting an
error in the flexspi DTS node and updating the clock init for RT11xx
SOCs.
Note that in addition, the NXP hal must be updated to properly support
including the cache management driver for the Cortex M4.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add driver for MEC172x QMSPI with local DMA(LDMA). The driver
support SPI asynchronous operation.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
DMA controller is enabled and tested for cortex M7 core. The M7 core was
tested on the loop and channel link transfer tests.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
DMA controller is enabled and tested for cortex M7 core. The M7 core was
tested on the loop and channel link transfer tests.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
the RT685 contains an additional flexcomm peripheral, that supports
only I2C. This commit adds this peripheral to the device tree,
and enables pins and clocks for flexcomm15.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
There is currently no information available about the XIP
addresses for the nRF52840 and nRF5340.
Add this via a new 'reg' block in the relevant QSPI nodes, along with
names for the register blocks so they are easier to retrieve.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Adds a driver using the SNVS high power and optionally low power
RTC instances. A device specific function `mcux_snvs_rtc_set` is
provided to update the current counter value.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
GPIO10 was missing from RT11xx DTS, and is required to manage SD card
power. Enable this GPIO.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
MCUX PWM driver used hardcoded clock source. update driver to use clock
bindings to determine PWM peripheral clock frequency.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit adds support for IMX6SX PWM.
The PWM module is the same module present on the IMX7D and so dts
bindings has been renamed following the one present on linux.
Signed-off-by: Antonio Tessarolo <anthonytexdev@gmail.com>
Add initial support for nRF pin controller driver. The implementation in
this patch does not yet support any peripheral. Only states
representation and basic driver functionality is introduced.
Note:
The nrf_pin_configure function has been marked as __unused since it may
not be used in certain scenarios until all peripherals are supported by
the pinctrl driver. For example, if only UART/E is supported but the
board does not enable UART, the function will never get called. However,
that board will likely have other peripherals that will gain support in
the future.
Thanks to Marti Bolivar for bindings documentation.
Co-authored-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add the pinctrl state name (default) for the CAN peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use nrfx_gpiote and nrfx_ppi allocators to allocate channels
at runtime instead of fixed, device-tree based allocation which
is harder to maintain.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The Flexspi memory address defines the location of the externally
attached flash to the MXRT600 based board. The flexspi has two
different memory spaces for secure and non-secure access that are
not aligned for the Flexspi register space and the memory map
address space. The normal method of handling this via the two
different dts files for secure/non-secure is not able to handle
this because a base address is applied uniformly across multiple
reg items.
Changes include:
- pull flexspi out of peripherals block to allow it to be explicitly
expressed in the respective secure/non-secure SOC DTS files.
- move the flash size definition to the board level definition and
use the size of the actual flash device found on the board.
:
Signed-off-by: David Leach <david.leach@nxp.com>
Prescaler was misplaced in pwm binding, instead of timers binding.
For example, TIM6/TIM7 doesn't have PWM capability,
but have a prescaler.
This change also prepares the introduction of timer based counter
(which requires prescaler at timer level)
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Add the USB On-The-Go Supplement, Revision 2.0 in the DTS
of the stm32u575 and stm32u585 devices
(not for the stm32U5 serie).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Fix register addresses in rt11xx SOC dts. Flexcan1 was defined with an
incorrect register address, and watchdog 3 was incorrectly labelled as
watchdog 1. Watchdog 2 should not be enabled, as it is only accessible
from code running in the trustzone context.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add baseline support for mimxrt1160_evk Cortex M4 and M7 cores
UART shell, synchronization, and hello world have all been verified to
build and run correctly.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Convert all in-tree NXP FlexCAN instances from hardcoding the CAN bus
timing in time quanta to specifying a desired sample point of 87.5% as
recommended by CAN in Automation (CiA).
This allows for the CAN driver to calculate the optimal time quanta
based on the CAN clock and the requested CAN bitrate.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The FIU/UMA module in the NPCX chip provides an dedicated SPI interface
to access the SPI flash. This commit adds the driver support for it.
With this commit, the application can call the flash APIs
(via spi_nor.c) to access the internal flash of NPCX EC chips.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Change-Id: I32bbf09f6e014b728ff8e4692e48151ae759e188
Add SoC-specific code, the basic device tree and Kconfig data as well
as the corresponding linker command file for the Xilinx Zynq-7000
family of SoCs. This SoC - either as a QEMU simulation or on actual
hardware such as the Avnet/Digilent ZedBoard - is suitable as an ini-
tial target for the ARMv7 Cortex-A support.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
MEC172x eSPI driver, eSPI pin programming, interrupt updates related
to eSPI and other updates for MEC172x eSPI driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add a dedicated compatible for STM32MP1 clock control node.
Since, on such platform, clock configuration is done on A9
side, only the clock-frequency property is available.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a DTS description of timer5 to: STM32G474, STM32G484, STM32G473,
STM32G483, and STM32G471
Add a DTS description of timer5 to: STM32G474, STM32G484, STM32G473,
STM32G483, STM32G491, and STM32G4A1
Signed-off-by: Pete Dietl <petedietl@gmail.com>
Adds SPI support on LPSPI1 to the RT1010. LPSPI1 is available on pins
6, 8, 10, and 12 of J57 on the evaluation board
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit enables the LPSPI1 peripheral on the RT1015 EVK. LPSPI pins
are not populated by default, but headers can be added to J19 on the EVK
to access these signals
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The maximum supported speed according to the SX126x datasheet (I have
not found that information in the STM32WL datasheet or reference
manual). Increase the Sub-GHz SPI frequency from 1 Mhz to to 12 MHz,
which corresponds to a baud rate prescaler of 4 with a 48 MHz clock. It
also matches what is done the the STM32CubeWL package.
This reduces the time the MCU is kept running, thus reducing the global
power consumption.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This adds the uart4 device to the stm32f3_disco board
based on the stm32f303 device from STMicroelectronics
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit adds stm32f103xd series dts file that was missing.
Also, changed stm32f103xe.dts for highlighting the differences between
f103xd and f103xe series.
Signed-off-by: Deimantas Aukštkalnis <deimantas.aukstkalnis@teltonika.lt>
Since version 1.11.0, Full stack M0 binary requires 216K of flash
being available, while previously 212K were required.
Review flash partitioning to take it into account.
Additionally:
- update value in board yaml file.
- align value in package .dtsi file
Fixes#38735
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The NPCX I2C implementation contains two modules, an I2C port and an
I2C controller. Disable the I2C controller nodes by default and require
the user to enable both the I2C port and controller in the devicetree.
Signed-off-by: Keith Short <keithshort@google.com>
Fix a typo bug where sercom5 pinctrl has pad2 and pad3
has duplicated pads for pb0/pb2 and pb1/pb3.
Per the datasheet, pb2 and pb3 should be pad0 and pad1 respectively.
Signed-off-by: Ron Smith <rockyowl171@gmail.com>
The priority of the LPTim interrupt on each stm32 soc
is put at the same level as the SysTick. This priority
level is given by the system Handler priority reg
(SHPR3) when the PM is not configured.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
stm32f411 includes stm32f401 which do already correctly define spi4
The definition in stm32f411 was missing a clock attribute
Signed-off-by: Kim Bøndergaard <kim.boendergaard@escoglobal.com>
stm32f410, stm32f411 and stm32f412 enable the SPI5 device with
bit 20 on the APB2 clock
Signed-off-by: Kim Bøndergaard <kim.boendergaard@escoglobal.com>
Add a shim that allows using the nrfx PDM driver via the Zephyr API.
Add also missing devicetree nodes representing the PDM peripherals
in the nRF52 Series SoCs.
Extend the "nordic,nrf-pdm" binding with a new property that allows
specifying the clock source to be used by the PDM peripheral (so that
it is possible to use HFXO for better accuracy of the peripheral clock
or, in the nRF53 Series SoCs, to use the dedicated audio oscillator).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
add correct binding, fix size to 32MBit, add erase and write
block size to support mcuboot and rename to reflect the actual
flash model.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
Atmel sam0 adc peripheral have multiple interrupt vectors for same5x
devices. This configure interrupt vector by name to ensure that proper
interrupt handle will be executed.
Fixes#37779
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Compatible "soc-nv-flash" was removed as part as #38077,
while it should have been kept, similarly to what was done
on other SoCs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The max-erase-time property was introduced for the STM32 flash driver,
but it was inserted as an optional property in the generic
soc-nv-flash binding which is used by other SoCs.
Make it a required property in a new st,stm32-nv-flash binding
instead, since it is at present a vendor specific property.
Update the DTS files accordingly. Keep the existing "soc-nv-flash"
value in the compatible list in each case, so that DT_HAS_COMPAT(...
soc_nv_flash) tests on these nodes will still succeed, but put it
after a newly added "st,stm32-nv-flash" compatible, so that the
SoC-specific binding will be used as it is discovered first by the DT
tooling.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Change IPM_STM32_HSEM Kconfig definition so that it picks the correct
default automatically depending on which cpu node is enabled in the
device tree, rather than relying on board specific Kconfig overrides.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add Digital-to-Analog Converter driver (based on DACC module) for Atmel
SAM MCU family. Only SAME70, SAMV71 series devices are supported in
this version.
Tested on Atmel SMART SAM E70 Xplained board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Microchip MEC172x series I2C driver implementing controller
and target modes. The driver implemenents its own I2C port
pin control functions and does not depended upon pinmux. Future
updates will make use of PINCTRL when that subystem is finalized.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Following change of HSE clock binding, remove hse-bypass
which is no longer an option and replace it with hse-tcxo
which is the configuration closest to previous status.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Like the first instance of the dma in the stm32l3xx soc,
the second DMA instance of the stm32f373 is of the same type
V2bis (dma request is fixed (no dma-slot).
The dma-cell has channel and config.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add missing RADIO and EGU nodes. We already have compatibles for
these defined, and the peripherals are present, so define them for
consistency across SoCs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add missing EGU nodes. We already have a compatible for
these defined, and the peripherals are present, so define them for
consistency across SoCs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add missing RADIO and EGU nodes. We already have compatibles for
these defined, and the peripherals are present, so define them for
consistency across SoCs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add missing EGU and TIMER nodes. We already have compatibles for these
defined, and the peripherals are present, so define them for
consistency across SoCs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add missing RADIO and EGU nodes. We already have compatibles for these
defined, and the peripherals are present, so define them for
consistency across SoCs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add missing RADIO and EGU nodes. We already have compatibles for these
defined, and the peripherals are present, so define them for
consistency across SoCs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add missing FICR, UICR, RADIO, and EGU nodes. We already have
compatibles for these defined, and the peripherals are present, so
define them for consistency across SoCs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add missing FICR, UICR, RADIO nodes. We already have compatibles for
these defined, and the peripherals are present, so define them for
consistency across SoCs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The way we currently handle direction finding extension (DFE) support
on Nordic nRF5 controllers relies on required devicetree properties
related to DFE in the "nordic,nrf-radio" node.
That doesn't make sense on radios without DFE support, though.
Any .dtsi for an SoC without DFE support which has such a node would
require extraneous DFE related properties like dfe-antenna-num.
Instead of making the properties required, mark them optional. We
indicate the presence of DFE support via a new 'dfe-supported' boolean
property which the SoC .dtsi files can set (or not) depending on
support.
This gives us the opportunity to do some cleanup in the Kconfig,
removing CONFIG_HAS_HW_NRF_RADIO_BLE_DF since we know from the
devicetree whether DFE support is available.
Handle that change appropriately in radio_df.c. This gives us an
opportunity to improve readability in the devicetree-related macro
magic in that file.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Sort by unit address. This involves multiple files since there are
includes and secure/non-secure files to deal with.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Renames stm32g0 tim1 brk interrupt to brk_up_trg_com, such that the
naming aligns with stm32f0 series and drivers can find the interrupt
with a common name.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Add ADC driver version 2 for MEC172x using new in-tree headers
and device tree properties. Update the ADC shell for the new driver.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
The psoc6 SoC has 2 cores, each with different allowed priority ranges:
CM0: 0-3 (2 bits of NVIC prio, no prio reserved by the kernel)
CM4: 0-6 (3 bits of NVIC prio, one level reserved by the kernel)
Since some of the peripherals are only available to the CM4, those
should be set to a priority that is actually valid for it. In this case
the lowest possible one is 6, so transition from 7 to 6.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Microchip XEC has been using the standard NS16550 driver.
Using the standard NS16550 driver requires extra HW programming
for XEC UART in board level and did not support XEC GIRQ interrupt
programming. We add an XEC specific driver and remove UART specific
register programming from the board level and implement interrupt
support. Also, by implementing a SoC specific driver we can add
driver PM in the future.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Microchip XEC two custom DT properies girqs and pcrs cell sizes
are defined as constants. There is no need to replicate these
is the chip DTSI since the value cannot be changes. Fix the syntax
of the cell size constant to match the naming convention used
thoughout DT.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
The ipm_stm32_hsem driver is a virtual mailbox based on STM32 HSEM.
Since we already have LL_HSEM(low-level HSEM) API on the hal_stm32
module, looks there is no need to implement a new HSEM driver.
But there are still have some limitations, the HSEMx interrupt is
not shareable. If another HSEM user wants to use the HSEMx interrupt,
the ipm_stm32_hsem mailbox needs to be disabled.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
We try to reduce the ambiguity between 'soc/nuvoton/' and
'soc/nuvoton_npcx' folders. Most if soc vendors name their soc folder by
the company name with SOC_FAMILY suffix instead of the company name
directly. It is clearer if the soc company has different product lines
that aim to specific markets.
In this CL, the 'numicro' suffix is used for Nuvoton Microcontroller
production line. It distinguishes the 'npcx' suffix that used for
Nuvoton Embedded Controller (EC) of Notebook PC product line.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Update the Microchip XEC pinmux driver to use system I/O
routine for read/write of registers instead of direct use
of volatile and CMSIS defines. Add GPIO port number to
bindings instead of using hard coded value from chip headers.
Modify SoC DTSI pinmux syntax, requires "pinmux: pinumx {..."
or the DT macros will not work. Since pinmux is used by MEC152x
we update its chip pinmux DT.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
The booter (bootloader) behavior may be different in different NPCX
chip series. One example is that the booter sets host interface type in
NPCX7 series but leave the firmware to set it in NPCX9 series.
This commit adds a new DT node to record variants in its properties.
NPCX drivers can understand if they need to configure the related
setting by checking the node's properties.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
dtc v1.6.1 produces an error without specifying #address-cells
on an interrupt-controller node.
Fixes#36495
Signed-off-by: Eric Johnson <eric@liveathos.com>
Add watchdog support to the mimxrt685 platform.
The mimxrt685 platform is excluded from the watchdog
test case because the test case uses variables in the
noinit section that need to be retained through a reset
but the rt685 does not retain this memory through a
reset.
Signed-off-by: David Leach <david.leach@nxp.com>
Add Atmel sam0 sercom[uart] pinctrl bindings and implements pinctrl at
driver level. It changes all sam0 boards to use new feature and remove
pinmux driver dependency for sercom[uart]. The samples that require a
binding were update to keep consistency and avoid errors.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add initial basic description for Cortex-M33 based
stm32u5 soc series.
This encompass description for base nodes, such as:
- cpu
- flash
- clocks
- sram
Additionally, provide description for variant stm32u575Xi.
Related to clocks nodes, added bindings for stm32u5 specific
rcc node as well as msi and pll clocks.
Header file stm32_clock_control.h was also updated to support
these new bindings.
Note that for compatibility with existing definitions, clock
node describing main pll clock, known as "PLL1", was given two
labels: "pll" and "pll1".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The type of DMA for the stm32f0 devices was wrong
Its DMA is of type V2bis where the peripheral request is fixed.
The corresponding DMA cell has 2 elements.
The stm32f091 has two DMA instances.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add a shim that allows using the nrfx I2S driver via the Zephyr API.
Add also missing devicetree nodes representing the I2S peripherals
in the nRF52 Series SoCs.
Extend the "nordic,nrf-i2s" binding with a new property that allows
specifying the clock source to be used by the I2S peripheral (so that
it is possible to use HFXO for better accurracy of the peripheral clock
or, in the nRF53 Series SoCs, to use the dedicated audio oscillator).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Create version 2 of the MEC GPIO driver to support MEC172x to not
interfere with MEC152x. When the MEC172x ECIA interrupt aggregator
driver is ready, this driver will use ECIA for registering GPIO
interrupt callbacks instead of maintaining its own interrupt table.
Add V2 DT binding.
Add the Kconfig configuration settings for the MEC172x GPIO
V2 driver at the SoC and board level.
Add port id to DT allowing use of DT FOR EACH macro in the driver.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This CL moves the phandles which don't contain 'reg' prop. from 'soc' to
'soc-if' node since they are the interface phandles only. It also
prevents "missing or empty reg/ranges property" warning messages.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Update Microchip XEC RTOS timer driver adding MEC172x support and
using more device tree properities in the driver. We must also update
the XEC counter driver to use the new GIRQ DT properties.
Add new properties to RTOS timer and RTC timer YAML. These two timers
are linked due to option using a high speed timer for kernel busy wait.
Add Kconfig logic for XEC RTOS timer to MEC172x SoC.
Enable the Microchip XEC RTOS timer in the MEC172x evaluation board.
Add device tree nodes for most peripeherals.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
In the eeprom read operation, when rambuf was available
mutex was not unlocked after the read. Consequence of that is
that device was blocked after that read for incoming operations.
This commit fixes the issue
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add driver implementation and header files for a MEC172x
aggregated interrupt driver. Enable the parent(ECIA) node
to have the driver initialize interrupt hardware for use.
Enable child nodes for those GIRQs used for aggregation.
Refer to chip documention for the list of GIRQs restricted
to aggregation and those which support direct mode.
Add chip level device tree node for MEC172x EC interrupt
aggregator parent and GIRQ children. Each child node contains
a list of sources representing the source bit position in the
GIRQ registers.
Add DT bindings for ECIA and GIRQ nodes.
Add build file(s) and configuration items for the MEC172x ECIA
aggregated interrupt driver. Add and enable the MEC172x interrupt
driver on the MEC172x evaluation board(EVB). Enable parent node to
initialize ECIA hardware. Child nodes are left disabled until a
future driver needs them.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Add basic counter driver based on Timer Counter (TC) module for Atmel
SAM family.
Remarks:
- The driver is not thread safe.
- The driver does not implement guard periods.
- The driver does not guarantee that short relative alarm will trigger
the interrupt immediately and not after the full cycle / counter
overflow.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit adds dt definitions for the hw aes accelerator
on stm32g0 Series.
The accelertor is available on the following socs:
stm32g041, stm32g061, stm32g081, and stm32g0c1.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds a dt node for the hw aes accelerator of the
stm32l5 series.
The stm32l562Xe.dtsi file now includes the newly created
stm32l562Xe.dtsi with the additional aes definitions instead of the
stm32l552Xe.dtsi file.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Each stm32 dma can be of V1 or V2 or V2bis type. Each type
has a dma-cell with specific nb of element. The feature and slot
properties are not required depending on the stm32 family.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Implement a clock control driver for Microchip MEC172x handling
configuring the 32 KHz input sources for the PLL and peripheral-32k
clock domains. MEC172x differs from MEC152x. MEC152x had one 32K source
for both PLL and peripherals. MEC172x allows the two domains to use
independent 32 KHz sources. Device tree updated to provide addresses
of hardware used by the driver.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This adds the dts to PASS the tests/drivers/dac/dac_loopback
on the nucleo_f429zi board, when PA0 and PA4 are connected.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
reuse the lpc's lpadc driver for rt1170, modify the dts and add
some macro to shield some code of LPC series. Also add the
board support inside the tests/drivers/adc/adc_api/src/test_adc.c,
and a dts node:zephyr,user inside
samples/drivers/adc/boards/mimxrt1170_evk_cm7.overlay
Signed-off-by: Crist Xu <crist.xu@nxp.com>
Adding support for the stm32l051 devices.
Signed-off-by: Even Falch-Larsen <even.falch.larsen@nomono.co>
Co-authored-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added minimal device tree and board files to build Microchip
MEC172x. SOC layer stripped down to allow build for checking
compilation only.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
The zephyr sam gmac driver don't get register address and, in some
cases, peripheral id from devicetree. This replace headers constants
in favor of devicetree values.
This fix wrong Atmel SAME7x/SAMV7x gmac register address and add
missing peripheral id property for SAM family.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The current GMAC compatible not allow especialize properties by SoC
family. Split current generic Atmel GMAC compatible into two new
compatibles which are defined by SoC families. This increase the
freedom and avoid odd situations.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Define the subghz radio node in the module dtsi file, with the internal
RF switch connection and TCXO setting, and point at it from the
corresponding dev board file.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add a device node for the subghz radio in stm32wl.dtsi. The radio is
present in all chips of the series, so having the node there with the
common properties simplifies the board dts files.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
This adds support for controlling the SUBGHZSPI NSS line in STM32WL
devices. This is a special dedicated SPI port only connected to the
radio device internally, chip select happens through a bit in the PWR
module. Adding a special dt-property to identify the port, it all gets
built out on non-WL devices.
Deduplicate the existing dts bindings in the process, and add the new
one for the special spi with the new property.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add I2C bus initial support to Renesas R-Car SoC series.
Both I2C2 & I2C4 buses are supported on R-Car H3 board.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
This commit adds the dt node for rng to the stm32wl series
and sets it as chosen zephyr,entropy source.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds support for stm32g0 socs with integrated rng and hw aes
acceleratior, which are stm32g041, stm32g061, stm32g081, and stm32g0c1.
It also adds the definitions for the rng peripheral
and sets it as chosen zephyr,entropy source.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds the dts definitons for the seeed lora-e5 module.
Additionally I add myself as codeowner for the new dts/arm/seeed
directory.
This module packages a stm32wle5jc Sub-GHz Wireless Soc,
together with a 32MHz TCXO, a 32.768KHz crystal oscillator, and
power and RF circuitry.
With the introduction of lora support definitions for the radio
will be added in a future commit.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds dt support for stm32wle4, and stm32wle5 single core,
as well as stm32wl54 dual core socs.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds dma1, dma2, dmamux support in dtsi for stm32l5
series. This commit also fixes a compilation warning due to the
usage of upper case in "reg = <0x4000F400 0x400>".
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
add devicetree node for usart4 and usart5. usart4 and 5
shares the same interrupt line (14), hence both can't be enabled
at the same time.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Nuvoton provides different series MCU. The NPCX series has a specific
id, which can identify the real chip part number. This CL adds soc id
for the NPCX series.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
This commit adds max-erase-time element which holds the
maximum erase time of a sector or page or half-page for
all the series of stm32.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
Add the lptim1 device node definition and enable the corresponding
exti interrupt in sys_clock_driver_init().
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
The PS/2 module in npcx provides a hardware accelerator mechanism
including an 8-bit shift register, a state machine, and control logic
that handle both the incoming and outgoing data. The hardware
accelerator mechanism is shared by 4 PS/2 channels. To support it,
this CL separates the PS/2 driver into channel and controller drivers.
The controller driver is in charge of the PS/2 transaction. The channel
driver is in charge of the connection between the Zehpyr PS/2 API
interface and controller driver.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Add a device node for the FMC controller found in stm32f427, f437 and
f446 devices, works fine with the current memc_stm32_sdram driver.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
The NXP LPC syscon driver failed to build on several platforms for
various reasons. We need dts support on LPC55s1x and LPC55s2x, the
driver doesn't seem like it will work on LPC54114 so we exclude it
there for now.
Additionally, fix a dtc warning on LPC55s6x based on unit-address in
the node naming needing to be lowercase.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The atmel pwm driver doesn't have a easy way to test and show
functionality to users. This re-assign led-0 function from
gpio-leds to pwm-leds. The current led-0 entry at gpio-leds
was keep with status disabled, as refence. It allows test pwm
driver for SAM Cortex-M7 MCUs. The led-1 assume Zephyr sample
default led0 alias.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add the device tree data for the 4 Ethernet controllers integrated into
the ZynqMP SoC, GEM0 to GEM3.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
This CL introduces six properties, clock-frequency, core-prescaler,
apb1/2/3/4-prescaler in pcc (Power and Clock Controller) node to
configure clock settings. It also removed the original Kconfig options
used for the same purpose.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This commit fixes the compilation warning occurred due
to usage of upper case in "interrupt-controller@4000F400".
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This commit adds PWM support in dtsi for stm32l5 series. Adding
other timer nodes for different stm32l5 series PWM capability.
Signed-off-by: Sidhdharth Yadav <sidhdharth.yadav@hcl.com>
GPIOTE1 on the nRF5340 SoC is always accessible as a non-secure
peripheral. However, it is only defined in the non-secure DTSI file.
This is therefore a missing node in the secure DTSI file, since
non-secure addresses are accessible by secure software.
Move the node definition to a common include file and pull it into the
app core DTSI as well. To keep things clean, adjust the node labels so
that:
- 'gpiote0' and 'gpiote1' are defined in the secure DTSI
- 'gpiote0' is not defined in the non-secure DTSI
- 'gpiote' is defined in both secure and non-secure DTSIs
- 'gpiote' refers to the same node as 'gpiote0' in the secure DTSI
- 'gpiote' refers to the same node as 'gpiote1' in the non-secure DTSI
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The sram1 node in nrf5340_cpuapp.dtsi represents the SRAM accessible
to the network core on the SoC.
However, while the network core can access the app core's SRAM, the
app core cannot access the net core's SRAM. Therefore, the sram1 node
should only appear in DTSI files for the net core, and not the app
core.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The RAM of can instances starts directly after it's predecessor.
This commit fixes can2 and can3 support for stm32g4 series.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Property "st,prescaler" of binding "st,stm32-pwm" was set to 2
different default values 0 or 10000 in *.dtsi files.
Since this property rather depends on application than hardware
description, there is no reason to have 2 different default values
in use. Besides, it is a trap for pwm users that should take into
consideration this random default value.
Fix this by defaulting the property systematically to 0.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add radio peripheral to nrf5340_cpunet DTS. The peripheral
description includes antenna matrix congiuration for Direction
Finding extennsion.
Appropriate binding file for nRF radio peripheral already egxists.
There is no default antenna matrix configuration. Antennas number
and GPIOS mapping to DFEGPIOS is project specific.
Complete configuration must be provided by end user as overaly.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Moved can, spi, usb, usb_fs_phy nodes to f103X8 dts.
Adds CAN for f103X8 series.
Tested on stm32f103c8 soc.
Tested on stm32f103vb soc.
Signed-off-by: Bhavesh Bhojwani <bhaavesh.bhojwaani@gmail.com>
Add radio peripheral to nrf52820 DTS. The peripheral description
includes antenna matrix congiuration for Direction Finding extennsion.
Appropriate binding file for nRF radio peripheral already egxists.
There is no default antenna matrix configuration. Antennas number
and GPIOS mapping to DFEGPIOS is project specific.
Complete configuration must be provided by end user as overaly.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
This commit adds DAC1 support in dtsi for stm32f3 series. Some
stm32f3 series has DAC2 so adding the same where applicable.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This commit adds a closing parenthesis for soc model of stm32g050.
Resolves issue #36014
Signed-off-by: Bhavesh Bhojwani <bhaavesh.bhojwaani@gmail.com>
Since the valid bit-depth of RAM_PDn registers are different, this CL
introduces a 'ram-pd-depth' property in 'nuvoton,npcx-pcc' node if the
application needs to turn off the partial ram blocks for better power
consumption.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Arrange device-tree files of npcx7 series by following steps:
1. Move device-tree declarations of npcx family to npcx.dtsi.
2. Leave specific device declarations of npcx7 series to npcx7.dtsi.
3. Move chip series related mapping tables such as
npcx7-miwus-wui-map.dtsi and so on to npcx/npcx7 folder.
4. Move common device-tree declarations used in each npcx series to
npcx-miwus-wui-map.dtsi and so on to npcx folder.
Then, the npcx device-tree folders are arranged to:
dts/arm/nuvoton
|--npcx
| |--npcx7
| | |--npcx7-miwus-wui-map.dtsi
| | |--npcx7-alts-map.dtsi
| | |--.....
| |--npcx-miwus-wui-map.dtsi
| |--npcx-alts-map.dtsi
| |--.....
|
|--npcx.dtsi
|--npcx7.dtsi
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL replaces series-prefix "npcx7-" with family-"npcx-" for npcx dts
nodes such as 'espi-vws-map' and 'miwus-int-map'. Since we plan to
introduce the npcx9 and later series, adding a new node such as
npcx9-espi-vws-map for each series is more complicated and not
necessary.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add a port property to describe which hardware port a GPIO device node
is describing since we can't tell from the registers (as the registers
are interleaved in the same MMIO space).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove (disabled) MPU support for the NXP Kinetis K2x. At least the
MK22F51212, which is the only K2x supported by Zephyr so far, does not
contain an MPU.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The change removes the following warning:
Warning: /soc/tc@4000C000: simple-bus unit address format error,
expected "4000c000"
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Device Tree address mixup between
SAI2 <-> SPI2 and SAI3 <-> SPI3
Add functionality to SPI2/3
Tested on SPI2
Signed-off-by: Rico Ganahl <rico.ganahl@bytesatwork.ch>
Switch the interrupt controller address to lower case to avoid this
warning:
stm32f723e_disco.dts.pre.tmp:97.39-102.5: Warning (simple_bus_reg):
/soc/interrupt-controller@40013C00: simple-bus unit address format
error, expected "40013c00"
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
add dts bingings for dma usage
add dts support for adc with edma and hwtrigger
add a periodic_trigger feature to dts
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Add SCIF bus initial support to Renesas R-Car SOC series.
SCIF1 is used as main serial and shell output on R-Car H3 board.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Commit 233149eec5 moved flash sram nodes
under /soc for various nordic ICs, but the indentation isn't right for
52811. Fix it.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
For dmamux nodes the dma-requests property specifies the number of
peripheral request inputs(not nr. of request trigger inputs).
This commit fixes this for g4 series.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
reg value should match value provided within node name (as in pll@2).
Fix this to avoid warning.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
As the KW2XD is a SiP (System-in-package) the SPI1 controller on the MCU
is connected to the modem. As the pinctrl details for this in the
SoC dtsi file as these pins are not exposed in the pindata XMLs from
NXP.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Set SPI0 controller to default to being disabled in SoC dtsi files and
having the board dtsi files enable it. The only board that wasn't doing
this already was the frdm_kw41z.dts.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add clocks node and clocks to stm32l5 series.
PLL binding is reused from stm32l4 series.
Matching binding is updated to document that.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add clocks nodes for F0/F3/G0/G4 series.
For F0 and G0 series, update compatible for rcc node
to specify use of dedicated "st,stm32f0-rcc" compatible.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Remove default pll settings to ensure pll users are correctly
configuring all prescalers on purpose and avoid surprises.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit adds flash clock settings in device tree for stm32h7
series such that the stm32h7 flash driver can get the clock settings
from this dtsi file.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The current serial driver uses hard code configuration. Rework driver
to use pinctrl and enable full configuration from device tree.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Provided nodes reflect the clock tree of each series.
Clock nodes are disabled by default but populated with default
start up configuration. Main reason is the we don't want to
impact boards using Kconfig based clock configuration for now.
Exception to these rules:
- syslck: Default enabled, clock frequency and clock source not
provided
- pll: clock source not provided
This is made on purpose so that errors are triggered if parameters
essential to the board configuration are not provided.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
i2s1 is not present in all stm32f4 series. So moving the i2s1 node
from the top level stm32f4 dtsi file to the stm32fxx specific dtsi
files. Also in stm32f429zi, the sequence starts from i2s2, this commit
helps in having the right channel number.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
STM32G0 is supported by the st,stm32-dma-v2 driver.
This commit adds dma1 and dmamux dts bindings
for stm32g03x, stm32g05x and stm32g07x.
For stm32g0bx additionally dma2 is added.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This patch adds flash clock settings in device tree for stm32wb
series so that the stm32 flash driver can get the clock settings
from this dtsi file.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This patch adds flash clock settings in device tree for stm32l4
series so that the stm32 flash driver can get the clock settings
from this dtsi file.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This patch adds flash clock settings in device tree for stm32l1
series so that the stm32 flash driver can get the clock settings
from this dtsi file.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This patch adds flash clock settings in device tree for stm32g4
series so that the stm32 flash driver can get the clock settings
from this dtsi file.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This patch adds flash clock settings in device tree for stm32g0
series so that the stm32 flash driver can get the clock settings
from this dtsi file.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
Enabling pwm on timer3 for stm32l1 series in dtsi.
Adding other timer nodes for pwm capability.
Signed-off-by: Sidhdharth Yadav <sidhdharth.yadav@hcl.com>
Renesas RCar Gen3 series have up to 8 GPIOs
bank.
Add bank 5 and bank 6, that is used to manage user led and
switches on different demo board.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
The Compare match timer can be found on Renesas
RCar Gen3 soc series.
It depends on clock controller to supply clock to the
CMT module.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Most of the Renesas RCar Gen3 based SoC contains a Cortex R7
processor.
This processor has access to the same memory mapped devices than
the Cortex-A5x cores.
- CPU operates upto 800MHz
- Can use ram area from 0x40040000 to 0x42000000
- Has 512 interrupts on GIC-400 compliant with Arm GICv2
Add support for r8a77951 as first SoC of this series which is also
known as H3 ES2.0 and is present present on different boards such as
Salvator and R-Car Starter Kit(H3ulcb).
This first SoC definition is just enough to print Hello World in a
ram console.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Enabling PWM on timer1 for STM32F2 platform in dtsi.
Adding other timers nodes for PWM capability.
Signed-off-by: Sidhdharth Yadav <sidhdharth.yadav@hcl.com>
Define the FLASH_CCFG memory region from a devicetree partition instead
of from math in the linker file. Removing the special math case results
in the FLASH_CCFG region overlapping the FLASH region, but the linker
accepts this until the FLASH region actually starts placing variables
in the FLASH_CCFG region.
As a result, applications that don't fit in (FLASH_SIZE - 88) bytes will
still fail to link, just with an overlapping memory region error instead
of an overflow error.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Move the definition of the two IPC RAM blocks from `#define`'s in family
linker scripts to proper devicetree nodes. Use the devicetree nodes to
generate the memory regions.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Fixed the name of nodes in in espi-vw, miwu-wui, and miwu-int
device-tree node. This CL fixed missing nodes in CL d3a94fa8ab.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The following is the interrupt priority plan for ec application.
The original IRQ priority map in Chromium EC is:
- IRQ priority 0:
|-ITIM IRQ for Warning watchdog.
-IRQ priority 1:
|-UART IRQ for signle byte FIFO in npcx5 series.
(Ignore it since UART has 16 bytes FIFO in npcx7 and later series.)
-IRQ priority 2:
|-SHI IRQ for FIFO FULL and Half FULL event.
|-MIWU IRQ for SHI CS. (Wake-Up ASAP for handling data from SPI bus.)
-IRQ priority 3:
|-All MIWU IRQs for GPIO, MTC and eSPI VW events.
|-ITIM IRQ for task scheduling.
|-ITIM IRQ for time-out.
(No need in Zephyr since 64-bit timer support.)
IRQ priority 4:
|-All UART FIFO IRQs
|-All I2C controller IRQs
|-ADC IRQ for conversion event.
|-ESPI IRQ for generic eSPI bus events.
|-Host KBC IBF/OBE IRQs
|-Host PM IBF/OBE IRQs
|-Host port80 IRQ
|-PECI IRQ
IRQ priority 5:
|-Keyboard RAW IRQ
|-PS2 IRQ
Then, this CL arranges the priority of npcx interrupts in Zephyr as:
IRQ priority 0:
|-Reserved it for further requirements.
IRQ priority 1:
|-SHI IRQ for FIFO FULL and Half FULL event.
| (Will modify it in ec repo.)
|-MIWU IRQ for SHI CS (Will modify it in ec repo.)
IRQ priority 2:
|-MIWU IRQ for GPIO, MTC, T0 timer and eSPI VW events.
|-ITIM IRQ for task scheduling.
IRQ priority 3:
|-All UART FIFO IRQs
|-All I2C controller IRQs
|-ADC IRQ for conversion event.
|-ESPI IRQ for generic eSPI bus events.
|-Host KBC IBF/OBE IRQs
|-Host PM IBF/OBE IRQs
|-Host port80 IRQ
IRQ priority 4:
|-Keyboard RAW IRQ. (Will modify it in ec repo.)
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Cortex M0 Series only have two interrupt priority bits,
nevertheless all series set the priority per default to the invalid
value of 7.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Fixed the name of nodes in device-tree files by following rules:
If object is 'phandles', use underscores for object name.
If not, such as 'node' or 'property', use hyphens for object name.
This CL also applies normal style for all nodes in npcx device-tree
files.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The adc1 of the stm32f373 uses an address space and a bus that are
different from the other microncontrollers of the f3 family. So, let's
remove the adc1 node from the stm32f3.dtsi and add it directly, with
respective correct values, in each of the SoC variant files.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
STM32L011 and STM32L031 do not support USART1.
This commit moves the definition of the node to only
be present for MCUs which support the peripheral.
Signed-off-by: Guðni Már Gilbert <gudni.m.g@gmail.com>
TIM7 peripheral was defined for all STM32L4 chips
in the device tree when not every chip supports it.
This commit moves the node so that only chips
which support the peripheral have the node defined.
Signed-off-by: Guðni Már Gilbert <gudni.m.g@gmail.com>
The device tree includes CAN node can1 for all
STM32L4 chips when in fact they don't all support it.
This affects STM32L412xx and STM32L422xx.
Fixes#33896
Signed-off-by: Guðni Már Gilbert <gudni.m.g@gmail.com>
Use a combination of fixed-clock and fixed-factor-clock devicetree
nodes for describing the clock dividers/multipliers of the NXP Kinetis
System Clock Generator (SCG) present in the KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Split ARM and ARM64 architectures.
Details:
- CONFIG_ARM64 is decoupled from CONFIG_ARM (not a subset anymore)
- Arch and include AArch64 files are in a dedicated directory
(arch/arm64 and include/arch/arm64)
- AArch64 boards and SoC are moved to soc/arm64 and boards/arm64
- AArch64-specific DTS files are moved to dts/arm64
- The A72 support for the bcm_vk/viper board is moved in the
boards/bcm_vk/viper directory
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This commit creates two new files in the device tree
1. stm32l412X8.dtsi
2. stm32l412XB.dtsi
This will specifcally add stm32l412X8 to the device tree
which was not supported before. Also the memory
for stm32l412XB was not defined specifically before.
Signed-off-by: Guðni Már Gilbert <gudni.m.g@gmail.com>
Add remaining NXP KE1xF SoC dtsi files to support out-of-tree boards
using other variants of the KE1xF than the single in-tree board.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add dts files for the specific chip instances that are used on the
boards in prep of having pin data in devicetree. The pin data will
be specific to the given chip instance so we need to distinguish
unique chips for the same SoC as the pin mux will differ.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch introduces the support of the Low Power Timer
for the STM32L5xx from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Enabling I2C-1,2,3 support for STM32F2 platforms in dtsi.
This has been tested with mpu6050 sample application on I2C-1.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
Enabling SPI support for STM32F2 platforms in dtsi.
This has been tested with test_spi_loopback on SPI-1.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This CL introduces the Power Switch Logic (PSL) pads which detect the
wake-up events and turn on/off core power supply (VCC1) for ultra-low
-power consumption in npcx device-tree file.
By adding PSL input-pad objects, psl_in1, psl_in2, and so on, into
'psl-in-pads' property and configuring their 'flag' properties, the
related driver will configure them via soc specific functions later.
For example, if PSL input 1 pad that is plan to detect a 'falling edge'
event, this property should be:
vsby-psl-in-list {
psl-in-pads = <&psl_in1>;
};
And the flag property in psl_in1 should change to
&psl_in1 {
flag = <NPCX_PSL_FALLING_EDGE>;
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add dmamux1 dts bindings for stm32h7
series. Note that there is no dedicated
clock to enable for dmamux1 so we set the
clock of dma1. This is the way linux handle
this.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
Fix the clocks bindings of dma1 and dma2
for stm32h7 series. This is wrong probably
due to copy and paste.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
In the change to DTS driven clock divider values wrong values
were used in the dts file.
Fixes: #33559
Signed-off-by: David Leach <david.leach@nxp.com>
Add initial support for the Cortex-M55 Core which is an implementation
of the Armv8.1-M mainline architecture and includes support for the
M‑profile Vector Extension (MVE).
The support is based on the Cortex-M33 support that already exists in
Zephyr.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In NPCX chips, System Configuration module can configure not only
pinctrl but also misc. functionality such as glue and flash write
protection. This change moves the scfg driver from the pinctrl folder
to soc/arm/nuvoton_npcx/common and renames it to avoid confusion.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Restructures dts files(value line definitions are no longer included by
others), and adds additional devices(g05x and g0bx).
All newly added timer pwm prescalers are set to 0.
lpuart1 is moved from stm32g0.dtsi to stm32g031.dtsi, as it is not
available on stm32g0x0 soc.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
"interrupt-names: combined" propterty is only used for stm32 i2c driver,
remove all other existing occurences for stm32g0(adc, lpuart, usart).
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Add optional maximum-speed parameter to USB nodes. This affects all
defined stm32l4xx, except stm32l4rx and stm32l4sx
Signed-off-by: Guðni Már Gilbert <gudni.m.g@gmail.com>
This parameter is defined for stm32f405 which and is included into
stm32f469. The include order is as follows:
st/f4/stm32f4.dtsi
st/f4/stm32f401.dtsi
st/f4/stm32f405.dtsi <-- ram_size defined here
st/f4/stm32f407.dtsi
st/f4/stm32f427.dtsi
st/f4/stm32f429.dtsi
st/f4/stm32f469.dtsi
Refer to Application Note AN4879 from ST to view ram size for each MCU.
Signed-off-by: Guðni Már Gilbert <gudni.m.g@gmail.com>
Introduce PSoC-6 pinctrl infraestructure and definitions. This add
files to handle devicetree entries and following modifications:
- add pinctrl bindings
- update gpio bindings with pin-cells
- add pinctrl node and move gpio nodes inside
- declare pinctrl for current uart entries
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Add GPIO definitions to QuickLogic EOS S3 devicetree.
Co-authored-by: Jan Kowalewski <jkowalewski@antmicro.com>
Signed-off-by: Wojciech Tatarski <wtatarski@antmicro.com>
Signed-off-by: Jan Kowalewski <jkowalewski@antmicro.com>
In some stm32 series systick was disabled in order to
allow alternate use of lptim timer as kernel low power ticker.
Doing this, dts based definition of CORTEX_M_SYSTICK Kconfig symbol
is disabled and CORTEX_M_SYSTICK was redefined with 'default y'
in stm32 soc files which makes things more complex to handle to
alternate with LPTIM activation.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To keep the generic DMA device name as defined
in the dma framework config, renamed paxdma device
label to "DMA_1".
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Use kinetis SIM clock divider options set in device tree
instead of hardcoded values.
The kl25z device tree did not previously define a MCG node.
This has now been added with the general "nxp,kinetis-mcg"
binding.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
Use kinetis SIM clock divider options set in device tree
instead of kconfig.
The kv5x device tree originally used the undefined
"nxp,kv58-mcg" binding for the MCG node. This has been
replaced by the general "nxp,kinetis-mcg" binding.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
Use kinetis SIM clock divider options set in device tree
instead of kconfig.
Both the kw40z and kw41z device tree originally used an
undefined "nxp,kw41z-mcg" binding for the MCG node.
This has been replaced with the general "nxp,kinetis-mcg"
binding instead.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
add CAN_1 and CAN_2 hw modules support
Signed-off-by: Alexander Kozhinov <AlexanderKozhinov@yandex.com>
Co-authored-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update register addresses and NVIC/GIC interrupt numbers
according to the latest viper RTL version.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Add device tree nodes for the Digital-to-Analog (DAC) modules present
in the NXP Kinetis K2x series.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
Change dfe-ant-num propert name to dfe-antenna-num.
The change is conde to keep the same naming style
for all properies, like dfe-pdu-antenna property.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Add initialization of GPIOs that are used for antenna switching.
GPIOs provided to DFE extension in Radio peripheral, to drive
antenna switching, should be initialized in GPIO peripheral beforehand.
The initialization is optional and may be disabled by Kconfig.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Add quadspi node in stm32f7.dtsi and quadspi support to boards
stm32f746g_disco and stm32f769i_disco.
Note! Does not support DMA.
Signed-off-by: Helge Juul <helge@fastmail.com>
NPCX chip allows firmware to select the JTAG0/1 via bit 2/1 in the
DEVALT5 register. However, the selection logic is reverse
(i.e. 0:select; 1:not select.)
This change fixes the wrong setting of the invert field.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Change-Id: I2c080feaa7647e940463d9491b61a342c84a6141
The size of System Configuration register cannot exceed 0x70. Otherwise,
it will overlap the Debug Interface register which starts from
0x400c3074.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
In NPCX7 series, it contains two tachometer (TACH) modules that contains
two Independent timers (counter 1 and 2). They are used to capture a
counter value when an event is detected via the external pads (TA or
TB).
The CL also includes:
— Add npcx tachometer device tree declarations.
— Zephyr sensor api implementation for tachometer.
— Enable "tach1" device in npcx7m6fb.dts for testing.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL introduces power management driver that improves the efficiency
of ec operation by adjusting the chip’s power consumption to the level
of activity required by the application in npcx series.
The following list summarizes the main properties of the various chip
power states. Please refer the power.c file for more detail.
Main power states in npcx series include:
- Active: Core, RAM and modules operate at the clocks generated by PLL.
- Idle: Enter this state when the Core executes WFI or WFE instruction.
- Sleep: clock is stopped for most of modules but PLL is enabled.
- Deep Sleep: As Sleep mode but PLL is disabled.
- Standby: All power rails are turned off besides standby and battery
power rails.
And this CL implements one power state, PM_STATE_SUSPEND_TO_IDLE, with
two sub-states for Zephyr power management system.
Sub-state 0 - "Deep Sleep" mode with “Instant” wake-up if residency
time is greater or equal to 1 ms
Sub-state 1 - "Deep Sleep" mode with "Standard" wake-up if residency
time is greater or equal to 201 ms
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL introduces a kernel device driver implemented by the internal
64/32-bit timers in Nuvoton NPCX series. Via these two kinds of timer,
the driver provides an standard "system clock driver" interface.
It includes:
- A system timer based on an ITIM64 (Internal 64-bit timer) instance,
clocked by APB2 which freq is CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC.
- Its prescaler is set to 1 and provide the kernel cycles reading
without handling overflow mechanism.
- A event timer based on an ITIM32 (Internal 32-bit timer) instance,
clocked by LCLK which frequency is 32KHz and still activated when ec
entered "idle/deep idle" power state for better power consumption.
- Its prescaler is set to 1 and provide timeout event mechansim.
- Compensate system timer which clock is gating for better power
consumption after ec left"idle/deep idle" power state.
This CL passed starve, timer_api, and timer_monotonic test suites.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add device tree nodes for QDEC peripheral instances
for nRF5340 Application core.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Convert from device_get_binding to DEVICE_DT_GET. In doing this we
no longer need the label in the devicetree node so we remove that.
Removed all __ASSERT_NO_MSG(clk) since we'll get a build error if
DEVICE_DT_GET cant be satisfied, and the clock control api's will
handle reporting if the device_is_ready.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We've removed the need for label properties from the pinmux devicetree
nodes on all other controllers and its not required for the TI one, so
remove it from the .dts and drop label being required in the binding.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add ESPI SAF features to the Microchip eSPI driver as
a separate file. ESPI SAF depends upon the core eSPI
driver adding the ability to attach the system SPI
flash to the EC eSPI endpoint instead of the host
eSPI controller.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
nxp_k2x.dtsi: Corrects Multipurpose Clock Generator binding
to utilize nxp,kinetis-mcg. Assign MCG to FlexTimer devices.
Enable FlexTimer clocks via System Integration Module clock
gate control registers.
Kconfig.defconfig.mk22f12: Enable default use of
CLOCK_CONTROL_MCUX_MCG when CLOCK_CONTROL is selected.
Signed-off-by: Ryan Holleran <rhollerar@gmail.com>
This CL moves def_lvol_io_list device-tree node from npcx7m6fb_evb.dts
to npcx7m6fb.dtsi. The benefit of it is that we needn't add
def_lvol_io_list node for each board dts file if there are no 1.8V
io-pads on the platform. If so, add them in the specific board dts file
directly.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
In the wake of the removal of nRF5340 PDK board we also
remove the support for the nRF5340 Engineering A SoC.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The compatible for the ARMv8 timer should have been arm,armv8-timer and
not arm,arm-timer. The dts binding file name was correct, just the
compatible was wrong. Rename dts, binding, and associated code to use
arm,armv8-timer.
Fixes#31946
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The arm64 timer node has not reg property and thus shouldn't be a
child of the SoC MMIO node. Move the arm,arm-timer up one level
to address this warning.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
i2c_shell uses "I2C_" label prefix to get the device. However, NPCX
uses controller-port architecture. Users should access the ports
instead of the controllers. Change I2C_CTRLX & I2CX_PORTX to I2CCTRL_X
& I2C_X_PORT_X to guarantee i2c_shell could get the correct device by
autocomplete.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
Older LPC platforms use Flash IAP with a command style firmware command.
Tested on LPC54114 platform.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Reworks the NXP FlexSPI device tree bindings to configure controller and
device properties needed for an upcoming FlexSPI flash driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
gpt has internal divider, add dedicated attributes
nxp,gptfreq is added as required one
gpt can customize the gpt freq
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Timer 1 has two interrupts on STM32F0: TIM1_BRK_UP_TRG_COM_IRQn (13) and
TIM1_CC_IRQn (14). "brk" interrupt name does not reflect all the events
supported by the interrupt, so it has been renamed to "brk_up_trg_com".
On all other series except G0 timer 1 has a specific interrupt for each
event, so in such case "brk" is just fine.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
PSoC-6 SoC needs that user define the nvic interrupt number to bind
with the peripheral interrupt line for the Cortex-M0+ CPU. It uses
a multiplex before any NVIC interrupt line. The interrupt vector is
selected using interrupt-parent property with the intmux_chN number
reference.
Note: The PSoC-6 SoC allows that both CPUs receive the same interrupt.
A tipical use is GPIO interrupt handle and user is responsable to
define interrupt line, priority and take care of enable same peripheral
instance on both CPUs only when appropriated.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
The psoc6.dtsi file declare a reference to nvic. Since it was proper
defined at psoc6_cm0/4.dtsi files this entry is redundant. Drop the
useless entry.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Enable slave support for I2C device instances. Slave mode is
interrupt based, wheras master mode is still based on polling.
Remove ENI bit in master configuration since it is not needed for
master mode.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Add the girq and girq-bit fields to the binding. This allows
encoding GIRQ related information inside device tree.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Add radio peripheral to nrf52833 DTS including antenna matrix
congiuration for Direction Finding extennsion.
Add appropriate binding file for nRF radio peripheral.
There is no default antenna matrix configuration. Antennas number
and GPIOS mapping to DFEGPIOS is project specific.
Complete configuration must be provided by end user as overaly.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
This commit add support for i2c on imx6sx.
I2C support is based on imx7d and requires NXP HAL.
The Device Tree binding is also changed to better reflect that i2c
driver support both imx6sx and imx7d.
Signed-off-by: Antonio Tessarolo <anthonytexdev@gmail.com>
Part of GPIO pads in npcx series support low-voltage (1.8V) level
detection. In order to introduce this feature, this CL adds a new
NPCX-specific controller property, lvol_io_pads, in devicetree file.
For example, here is devicetree fragment which turn on low-voltage
support of i2c1_0 port.
/ {
def_lvol_io_list {
compatible = "nuvoton,npcx-lvolctrl-def";
lvol_io_pads = <&lvol_io90 /* I2C1_SCL0 1.8V support */
&lvol_io87>; /* I2C1_SDA0 1,8V support */
};
};
Then these pads will turn on 1.8V level detection during initialization.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This property is required information for extracting PSEL bits relevant
to peripheral pinmux from this node.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
'reg' attribute removed from overall stm32l1 dts,
so eeprom size has to be specified for each SoC
in stm32l1x series.
Adds remaining stm32l1x SoCs that didn't have eeprom size specified yet.
Eeprom size added in stm32l151Xb-a & stm32l151X8-a dtsi files,
(based on device overview in datasheet DocID024330 Rev 5).
Eeprom size added in stm32l151Xb dtsi file (based on
device overview in datasheet DocID17659 Rev 12).
Signed-off-by: Noelle Clement <noelleclement@hotmail.com>
In npcx7 series, the Timer and Watchdog module (TWD) generates the
clocks and interrupts used for timing periodic functions in the system.
It also provides watchdog reset signal generation in response to a
failure detection.
The CL also includes:
— Add npcx watchdog device tree declarations.
— Zephyr watchdog api implementation.
— Add Watchdog definitions for npcx7 series in
tests/drivers/watchdog/wdt_basic_api/src/test_wdt.c for
supporting test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Add device tree description for qspi node on STM32L4 and
signals on whole family.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
STM32L152xC SoC differs from other L1 SoCs in RAM (32KiB) and
flash (256KiB) size, EEPROM size (8Kib) and amount of interrupts
(57, see STM32Cube). Devicetree and Kconfig support.
Signed-off-by: Noelle Clement <noelleclement@hotmail.com>
after 7c699348a8
Convert drivers to new DT device macros
now the device name is aligned with label so we need
align them to default config
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
The npcx7m6fb dts defines i2c controller and ports, where the controller
is a property in the port node definition and the device nodes should be
defined as subnodes of the port.
This changes the binding definitions to reflect that, defining the port
as an i2c-controller so that in can inherit sub-nodes for i2c devices,
and the controller as a generic node.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add binding for the Nordic ECB (AES electronic codebook mode
encryption) peripheral and corresponding devicetree nodes for
nRF SoCs that feature this peripheral.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Since MDK was updated and now it contains the definition of QDEC
peripheral for nRF52805, the DT node representing this peripheral
can be processed normally.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
"st,mem2mem" property is supposed to be limited to dma-v1.
Remove its use in dma-v2 components.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
2 versions of DMA hardware blocks could be found across stm32 series.
In order to simplify the handling of matching Kconfig symbols,
make this visible in dts files by creating "st,stm32-dma-v1" and
"st,stm32-dma-v2" and set them accordingly in dtsi files.
Duplicate and update related bindings to reflect that new state.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The STM32F105xx is effectively an STM32F107xx without Ethernet. As such,
it's possible to include the STM32F105's device tree from STM32F107, and
add in any additional nodes (currently just DMA2, though according to
the datasheet, this may be supported by the STM32F105xx and other parts
too).
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
The interrupt numbers for two socs for the gpio peripheral was wrong.
This commits corrects this issue for the relevant socs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
The watchdog and rng nodes were a sub-node of the gpio node.
This commits corrects this issue for the relevant socs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Adds support for ADC on G0 series.
Simple implementation: sequencer not fully configurable,
and only one common sampling time.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This patch enables the rtc clock on the stm32g4 soc
from STMicroelectronics.
Even if the set by default (reset value of theRCC_APB1ENR)
the bit is marked as 1.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Instead of hard-coded values for interrupt priorities in DT nodes, use
a macro that additionally can be overridden at the board or application
level. This allows, for instance, changing the interrupt priorities for
all but one peripheral without using a lengthy overlay file.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This file originally added a "nordic,nrf-sw-pwm" node with a few basic
properties that were common to all nRF51 and nRF52 series SoCs. There
is no implementation of SW_PWM available for other nRF series. At the
time this file has been created, there was only nRF91 apart from nRF5x,
but when nRF53 appeared, the name of this file became misleading.
Recent addition of common disabling of the systick node made it clear
that such common file for all nRF SoCs is convenient.
To prevent further confusion, rename this file to nrf_common.dtsi and
keep there only stuff actually common to all nRF series, moving the
SW_PWM related node to particular SoCs that use it (this is actually
consistent with how all other nodes, that also have some properties
common to several or even all nRF SoCs, are defined).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Change io status of host-uart device to "disabled". It was caused by a
mistake during solving conflicts.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The NPCX SMB modules provides full support for a two-wire SMBus/I2C
synchronous serial interface. Each SMBus/I2C interface is a two-wire
serial interface that is compatible with both Intel SMBus and Philips
I2C physical layer. There are 8 SMBus modules and 10 buses in NPCX7
series.
In NPCX7 series, the SMB5 and SMB6 modules contain a two-way switch to
support two separate SMBus/I2C buses (ports) with one SMB module
(controller) Please refer Section 4.7.2 in the datasheet. In order to
support it, this CL seperates the i2c driver into port and controller
drivers. The controller driver is in charge of i2c module operations
and internal state machine. The port driver is in charge of pin-mux
and connection between Zehpyr i2c api interface and controller driver.
All of modules have separate 32-byte transmit FIFO and 32-byte receive
FIFO buffers. These FIFO buffers reduce firmware overhead during long
SMBus transactions by allowing the Core to write or read more than one
data byte at a time to/from the SMB module.
The CL also includes:
— Add npcx i2c port/controller device tree declarations.
— Zephyr i2c api implementation.
— Add "i2c-0" aliases in npcx7m6fb.dts for i2c test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
The System Glue module includes the three major functions:
— Power Switch Logic (PSL)
— SMBus multi-bus, wake-up support
— Simple Debug Port (SDP)
In NPCX7 series, the SMB5 and SMB6 modules contain a two-way switch to
support two separate SMBus/I2C buses (ports) with one SMB module
(controller). Since a single SMB module is able to serve only one
SMBus/I2C bus at a time, SMB_SEL registerin Glue module is used to
control theconnection of I2Cn_0 and I2Cn_1 interface pins to the SMBn
module (where n is 5, 6).
This CL provides a soc specific pin-control function called
"soc_pinctrl_i2c_port_sel" to switch buses (port) of the same SMB module
(controller). It will be used in the following i2c driver.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This commit adds the dtsi config for the stm32f303k8.
In addition fixing to long line for author.
Fixing sram0 memory size.
Signed-off-by: Sebastian Schwabe <sebastian.schwabe@mailbox.tu-dresden.de>
Use PPIs 0-5 consistently across nRF51x and nRF52x for SW
PWM driver. Bluetooth LE controller's use of PPI has been
adjusted to use PPI 6-19 based on features enabled.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add 'label' as a required property for nxp,kinetis-pinmux devices. In
addition we cleanup the kw2xd node labels for the pinmux devices to
match the SoC docs and use 'port' instead of 'pinmux_'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
So far 'timer-instance' DT property was the way to configure TIMER which
was used for generating PWM signal. Replace that by using 'generator'
phandle, so we get prepared for supporting RTC instances as PWM signal
generator.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Flash controller support is not yet ready on M4 core.
Remove the chosen declaration to make it clear.
Additionally, generate a build error if this driver is compiled
on M4 core.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Define erase and write block size for M4 side flash controller.
Additionally move compatible definition from package to soc file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Define write and erase block size for supported stm32h7 devices
Use a specific compatible string for stm32h7 devices for the flash
driver
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
In order to prevent user turns on the pin-mux of devices has io-pads
unexpectedly, this CL added a new device definition for host uart
device. The pin-mux of host uart interface is enabled only if we set its
status as "okay" in dts file of board folder.
The following npcx7 drivers will meet:
1. Default status property of npcx devices with io-pads such as espi,
pwm, uart, host uart and so on should be "disabled".
2. Switch pin-mux by changing status property to "okay" in dts file of
board folder.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Define write and erase block size for supported stm32h7 devices
Use a specific compatible string for stm32h7 devices for the flash
driver
Signed-off-by: Nicolas VINCENT <nicolas.vincent@vossloh.com>
NPCX7 includes a 10-bit resolution Analog-to-Digital Converter (ADC). Up
to 10 voltage inputs can be measured and a internal voltage reference
(VREF), 2.816V (typical) is used for measurement. It can be triggered
automatically in Autoscan mode. Each input channel is assigned a
separate result register, which is updated at the end of the conversion.
The CL also includes:
— Add npcx adc device tree declarations.
— Zephyr adc api implementation.
— Add adc definitions of npcx7 in
tests/drivers/adc/adc_api/src/test_adc.c for supporting test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
SRAM base address and size are currently hardcoded in the defconfig.
This is wrong because symbols like KERNEL_RAM_SIZE and KERNEL_VM_BASE
are not currently being set. Fix this by adding the correct DTS entry.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
STM32H753xx is similar to STM32H743xx except that it has crypto/hash
hardware acceleration and the memory configuration is always 2Mbytes
flash and 1Mbyte RAM.
Signed-off-by: Petri Oksanen <petri@iote.ai>
These were found while reviewing the device tree and register addresses.
They are now the same as for the LPC55S28.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
sram4 is not connected to USB. The following sram area that is not part
of the device tree is. So the comment is removed with this commit.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Remove the zephyr,flash-controller chosen node from the NXP KW40Z SoC
series devicetree. The MCUX SDK version for this SoC is too old to work
with the Zephyr MCUX flash driver shim.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add tx/rx pl330 channel IDs for the iProc PCIe client usage.
pl330 channel 0 is allocated for Tx DMA (Device to Host write) and
pl330 channel 1 is allocated for Rx DMA (Host to Device read).
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
This commit adds a new driver category for memory controller
peripherals. There is no API involved for now, as it has not been found
necessary for first implementation.
STM32 Flexible Memory Controller (FMC) is the only controller supported
for now. This peripheral allows to access multiple types of external
memories, e.g. SDRAM, NAND, NOR Flash...
The initial implementation adds support for the SDRAM controller only.
The HAL API is used, so the implementation should be portable to other
STM32 series. It has only been tested on H7 series, so for now it can
only be enabled when working on H7.
Linker facilities have also been added in order to allow applications to
easily define a variable in SDRAM.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add Atmel SAM I2C Two-wire Master Interface (TWIM). The SAM
i2c controller have specifics regs depending of operation mode
Master/Slave and the bindings are for Master only.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add i2c1 interface for stm32l552xx and stm32l562xx microcontrollers
and enable i2c1 that connects to lsm6dso sensor module on the
stm32l562e_dk board.
Signed-off-by: Yestin Sun <sunyi0804@gmail.com>
Made sram0 visible for NETWORK core target. The core might
access sram0 as shared region might be defined inside it.
Made sram1 visible for APPLICATION core target for keeping
consistence.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Removes peripheral aliases from all NXP SoCs (Kinetis, LPC, and i.MX),
which are no longer being used after converting their associated drivers
to use DT_INST macros. The watchdog alias remains because it is used by
tests/drivers/watchdog/wdt_basic_api/
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
These MCUs have 32Kbytes of Flash and 8Kbytes of RAM. They are still
able to run a number of samples.
Signed-off-by: Steven Daglish <s.c.daglish@gmail.com>
The number of capture/compare registers available on a peripheral
should be exposed in devicetree.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The nRF5340 (P)DK is equipped with the MX25R64 flash memory. Add a dts
node for that chip in the board definition as well as the missing QSPI
node in the nRF5340 SoC definition.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Reworks the mcux ethernet driver to use DT_INST_FOREACH_STATUS_OKAY and
eliminate a lot of duplicate code between instance 0 and instance 1.
Renames the ERR_MISC interrupt to ERR due to an issue with the
underscore in the device tree preprocessor macros.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors nxp i.mx, kinetis, and lpc soc-level device trees to use
DT_SIZE_K and DT_SIZE_M macros to define internal memory sizes. This is
self documenting and easier to read.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
MSI-X PVM feature requires snoop interrupt for tracking configuration
space register (msix_cap) update and PCIe PMON lite interrupt for
tracking MSI-X table update. Add both the interrupts for Viper M7 DT.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
The DMA channel number used for the DMA transfer can now
be specified from the device tree config files
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
This defines the TRNG for EFM32GG11 and enables it for trng0
in the dts for the matching development kits.
Signed-off-by: Thorvald Natvig <thorvald@natvig.com>
This defines wdog0 and wdog1 for the EFM32GG11 MCU and enables wdog0
in the dts for the matching development kits.
Signed-off-by: Thorvald Natvig <thorvald@natvig.com>
While the STM32H7 features a special dual mode operation for ADC1 and
ADC2, the register specified for adc1_2 node was actually the one for
ADC1 in normal single mode operation.
This commit fixes register for dual mode and adds adc1 and adc1 nodes.
Signed-off-by: Martin Jäger <martin@libre.solar>
Commit ac31c4e458 updated the mcux
ethernet driver to get the ethernet peripheral base address from device
tree instead of an nxp hal preprocessor macro. This exposed an error in
the k6x device tree and caused a runtime assertion in networking
applications on the frdm_k64f board:
ASSERTION FAIL [instance < (sizeof(s_enetBases) / sizeof((s_enetBases)[0]))] @ WEST_TOPDIR/modules/hal/nxp/mcux/drivers/kinetis/fsl_enet.c:323
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In npcx7 series, there're 8 Pulse Width Modulator (PWM) modules and each
one support generating a single 16-bit PWM output. A 16-bit clock
prescaler (PRSCn) and a 16-bit counter (CTRn) determine the cycle time,
the minimal possible pulse width, and the duty-cycle steps.
Beside introducing pwm driver for Nuvoton NPCX series, this CL also
includes:
1. Add PWM device tree declarations.
2. Zephyr PWM api implementation.
3. Add aliases in npcx7m6fb_evb board device tree file for supporting
samples/basic/blinky_pwm application and pwm test suites
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Only difference compared to existing Xe variant is less flash memory.
Existing nodes for DAC were moved up one level to stm32g474.dtsi
Signed-off-by: Martin Jäger <martin@libre.solar>
Change default pinmux of functional pads to GPIOs. It includes:
1. PIN96.A0.A2.A4 - If internal flash is supported
2. PIND2.00 - Default PSL inputs
3. PIN31.30.27.26.25.24.23.22 - Keyboard inputs
4. PIN21.20.17.16.15.14.13.12.11.10.07.06.05.04.82.83.03.B1 - Keyboard
outputs
5. Add description for soc_pinctrl_mux_configure() usage.
It also fixed the typo and inverse mistakes in npcx7-alts-map.dtsi.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This CL adds more comments for each macro functions used for device tree
file for better explanations. It also changes all hex values in soc.c to
lower case.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
This CL contains the drivers of NPCX Host Sub-Modules that serve as an
interface between the Host and Core domains. For most of them, the Host
can configure these modules via eSPI(Peripheral Channel)/LPC by
accessing 'Configuration and Control register Set' which IO base address
is 0x4E as default. And the interrupts in core domain help handling any
events from host side.
In this commit, we introduced six host sub-modules. It includes:
1. Keyboard and Mouse Controller (KBC) interface.
2. Power Management (PM) channels.
3. Shared Memory mechanism (SHM).
4. Core Access to Host Modules (C2H).
5. Mobile System Wake-Up functions (MSWC).
6. Serial Port (Legacy UART)
The tasks in application layer such as 8042, ACPI and host command can
cooperation with this driver by connecting api or callback functions.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
In npcx7 series, all of them support the Intel Enhanced Serial
Peripheral Interface (eSPI) Revision 1.0. This specification provides a
path for migrating host sub-devices via LPC to a lower pin count, higher
bandwidth bus. In addition to Host communication via the peripheral
channel, it provides virtual wires support, out-of-band communication,
and device mastering option over the Chipset SPI flash.
Becisdes introducing eSPI device in npcx7, this CL also includes:
1. Add eSPI device tree declarations.
2. Add npcx7-espi-vws-map.dtsi to present the relationship between eSPI
Virtual-Wire signals, eSPI registers, and wake-up input sources.
3. Zephyr eSPI api implementation.
4, Add OOB (Out of Band tunneled SMBus) support.
5. Add configuration files for eSPI test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
stm32f1 series pin controller IP is not compatible with other stm32
series.
Set the dedicated st,stm32f1-pinctrl compatible for pinctrl node.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename compatible st,stm32-pinmux to st,stm32-pinctrl to better
reflect the nature of upcoming child nodes.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32L151xC SoC differs from other L1 SoCs in RAM (32KiB) and
flash (256KiB) size, and amount of interrupts (57, see STM32Cube).
Devicetree and Kconfig support.
Signed-off-by: Noelle Clement <noelleclement@hotmail.com>
Adds imx rt support.
Allows n-number of can interfaces based on device-tree.
Adds a "common" irq name.
Added CAN bus pins and dts for 1060 and 1064 EVK.
Signed-off-by: Rick Talbott <rtalbott@fastmail.com>
* Add ADC2 and ADC3 to the F103xE definition.
* Add a dtsi file for the F103xG based on the F103xE.
The F103xG has 1 MB of flash, 96 KB of RAM, and additional timers
TIM9/10/11/12/13/14.
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
update rt6xx series sram mapping to skip 0x180000,
reserved for DSP usage.
this fixes tests/subsys/debug/coredump for this board
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
The sam4l pinctrl contains two entries with wrong values. Fix the
typo to create valid pinctrl map.
Fixes#28538.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Change #28199 introduced systick configuration from device tree.
For now this should not be used on platforms that support alternate
tick source, as this is the case on l4 and wb series with LPTIM.
Until dts allows to configure lptim from dts, keep systick disabled
by default on these platforms.
Fixes#28280
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use setting from devicetree to drive the default setting for
CORTEX_M_SYSTICK. We update the dts files to default systick to be
enabled since the major of cortex-m platforms utilize it by default
(except on Nordic SoCs, TI CC13x2/CC26x2 and MEC1501 in which we
default to disabled).
Fixes#25299
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for UARTs 3-6 to the stm32f030xc SoC. These additional UARTs
share a single interrupt line, so only one may be enabled at a time.
Signed-off-by: Brian Kubisiak <brian@kubisiak.com>
This CL configures the UART wake-up event triggered from a falling edge
(START condition) on CR_SIN pin. It also includes:
1. Introduce wui_maps property in yaml file to present relationship
between Wake-Up Input (WUI) and UART device.
2. Implement wake-up mechanism by MIWU api functions.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Add gpio support for Nuvoton NPCX series. This CL includes:
1. Add GPIO device tree declarations.
2. Introduce wui_maps property in yaml file to present relationship
between Wake-Up
Input (WUI) and 8 IOs belong to the device.
3. Zephyr GPIO api implementation.
4. GPIO callback functions implementation with MIWU api functions.
5. Overlay file for gpio basic tests
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
The device Multi-Input Wake-Up Unit (MIWU) supports the embedded
controller (EC) to exit 'Sleep' or 'Deep Sleep' power state which allows
chip has better power consumption. Also, it provides signal conditioning
such as 'Level' and 'Edge' trigger type and grouping of external
interrupt sources of NVIC. The NPCX series has three identical MIWU
modules: MIWU0, MIWU1, MIWU2. Together, they support a total of over 140
internal and/or external wake-up sources.
In this CL, we use device tree files to present the relationship bewteen
MIWU and the other devices in different npcx series. For npcx7 series,
it include:
1. npcx7-miwus-int-map.dtsi: it presents relationship between MIWU group
and NVIC interrupt in npcx7. Please notice it isn't 1-to-1 mapping.
2. npcx7-miwus-wui-map.dtsi: it presents relationship between input of
MIWU and its source device such as gpio, timer, eSPI VWs and so on.
This CL also includes:
1. Add MIWU device tree declarations.
2. MIWU api function declarations and implementation to configure signal
conditions and callback function mechanism. They can be be classified
into two types. One is for GPIO which connects original gpio callback
implemetation and the other is for generic devices such as timer,
eSPI, and so on.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
In the SoC that comes on the nRF5340 DK the number of MPU
regions in the nRF5340 Network MCU is 8, instead of 16. We
fix this in DTS by introducing different .dtsi headers for the
different SoC part variants: the nrf340 Engineering A (first
SoC revision, present in the nRF5340 PDK) and the nrf5340
(second SoC revision, present on nRF5340 DK).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add IUART driver based on MCUX SDK. This driver is used to provide
serial console support on i.MX8M Mini SoC.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Skeleton board support for the npcx7m6fb evaluation board from Nuvoton
Technology. This CL also includes:
1. Add ecst python scripts to append the header used by NPCX ROM.
2. Add openocd configuration scripts for "west flash".
3. Add monitor FW binary file for programing/verifying embedded flash
in NPCX series.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Add pin controller support for Nuvoton NPCX series
Add pin-mux controller support for Nuvoton NPCX series.
This CL includes:
1. Add pin controller device tree declarations and introduce alt-cells
to select pads' functionality.
2. Add npcx7-alts-map.dtsi since the mapping between IO and controller
is irregular and vary in each chip series.
3. Add nuvoton,npcx-pinctrl-def.yaml and its declarations to change all
pads' functionality to GPIO by default.
4. Pinmux controller driver implementation.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Add clock controller support for Nuvoton NPCX series. This CL includes:
1. Add clock controller device tree declarations.
2. Introduce clock-cells in yaml file clock tree to get module's source
clock and turn off/on the its clock
3. Clock controller driver implementation.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Initial support for Nuvoton NPCX7M6FB SoC of NPCX series which is a chip
family of embedded controllers (EC) and targeted for a wide range of
portable applications. We implemented the SoC skeleton in
soc/arm/nuvoton_npcx since there're many chip families in Nuvoton and
aim to different markets such as PC, General MCU, and Audio. The
architectures and hardware modules are different between them. Hence, we
suggest using the company name plus with chip series for better
understanding.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The EFR32MG21 uses a different kind of clock for watchdogs.
It requires an additional peripheral-id parameter in the dts to get the
proper clock as it is based on the watchdog's ID i.e., cmuClock_WDOG#.
Signed-off-by: Steven Lemaire <steven.lemaire@zii.aero>
The peripheral is the same on the SAMD20 and SAMD21 except for
different clock and interrupt settings. There is no DAC on the SAMR21.
Leave disabled by default as the DAC is fairly power hungry.
Signed-off-by: Michael Hope <mlhx@google.com>
This commit adds the device tree nodes and bindings for the I2C
controllers of the LPC11U6X MCUs
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
This commit adds basic support for the clock controller used in
lpc11u6x MCUs.
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
This commit adds a bindings for the clock controller used in lpc11u6x
MCUs. It also adds a clock-controller node for the lpc11u6x soc series.
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
This patch adds the DT nodes and binding for the pinmux registers,
aka IOCON (I/O control), found on the LPC11U6x MCUs.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
Now that the patches have landed, enable more of the peripherals on
the board.
In particular:
* Enable PWM on the LED
* Enable the SPI, USB, and DMA
* Enable the bootloader support
* Add to the PWM and SPI tests
* Call these out in supported.yaml
Signed-off-by: Michael Hope <mlhx@google.com>
For true mmio-sram, arc,iccm, arc,dccm nodes we should not be setting
device_type = "memory". This should be used for true DRAM regions of
memory and not on SoC SRAMs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Several peripherals are non-functional in the ENG_A revision
of nRF5340 (Application MCU) so we delete the corresponding
DTS nodes in the device description.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Rename the nRF5340 QKAA variant .dtsi headers (Application
MCU) by adding an Engineering A (Eng A) suffix. This is done
to indicate that the headers should be explicitly used when
building for a board that contains the Engineeering A nrf5340
SoC variant.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We need to use CPUAPP and CPUNET instead of CPU0 and CPU1
terminology, because those terms are the ones used
throughout the DeviceTree definitions for nRF5340 SoC.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Move the definition of the number of MPU regions
(num-mpu-regions) in a SoC variant-specific header
instead of the common .dtsi for nRF5340 Application
MCU. This allows us to define different SoC variants
with different number of MPU regions available.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit renames the nrf5340_cpuapp_common.dtsi header
to nrf5340_cpuapp_peripherals.dtsi. This name is more
appropriate, as the header contains DT definitions for
peripherals, accessible from either Secure or Non-secure
execution environment (i.e. not accessible exclusively
by Secure or Non-Secure).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds the device tree TCC (Timer/Counter for Control
Applications) peripheral definitions for the Atmel SAM D5x and E5x
series SoCs.
The SAM D5x/E5x series SoCs have five instances of the TCC peripheral:
TCC# Channels Waveform Output Counter Size
0 6 8 24-bit
1 4 8 24-bit
2 3 3 16-bit
3 2 2 16-bit
4 2 2 16-bit
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Add support for STM32L0X using the generic STM32 backend. This is
quite a significant change since the L0 series uses a slightly
different flash controller. Refactor the generic backend to better
support different block sizes and the L0's register interface.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Add initial support for nuvoton numicro m48x SoC series, basic
init and uart functionality are covered with gpio and clock
directly relies on HAL.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
The SAMD21 series has three timer/counters with a mix of channels and
resolutions. Note that the SAMD20 only has TC peripherals and no TCC
peripherals which is why the changes are in samd21.dtsi.
Signed-off-by: Michael Hope <mlhx@google.com>
Timer interrupts have been added for all STM32 SoC. H7 series already
had the interrupt definitions. The IRQ number and names have been taken
from the STM32Cube HAL header files.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add support for the polarity flag in the STM32 PWM driver.
STM32 boards using PWM have been updated accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Aliases defined for peripheral nodes in the nRF SoC definitions were
used in drivers to properly match the hardware instances.
After the drivers were converted to use the new DT API, these aliases
became needless.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable GPIO as a workaround to enable some SPI slaves are not correctly
controlled using the Flexcomm SPI device.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Those MCUs have 2KB RAM and 16KB FLASH memory, but they are still
powerful enough to run small configuration of Zephyr RTOS.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
The STM32L072 and STM32L073 comes with a hardware random number
generator. Add this to the device tree.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
This allows referencing the CPU in the board-specific DTS file.
Also fix warnings by making the addresses lower case.
Signed-off-by: Michael Hope <mlhx@google.com>
Adds a new LPTIM binding for stm32 soc,
based on the timer binding. This will makes a specific filter
on dt_compat_enabled("stm32,lptim")
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The interrupts generated by the generic timer behave in
a level-sensitive manner. Change the DT to reflect the same.
Fixes: #25585
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Add the missing node and bindings. This is a secure-mapped peripheral,
so do not add it to the common include file
nrf5340_cpuapp_common.dtsi.
Fixes: #25493
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
In aarch64 DTs, priority and flags cells have been swapped,
fix the same.
Correct interrupt property per the GIC binding document
looks like:
interrupts = <irq_type irq_num irq_flags irq_priority>;
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Adds the required #io-channel-cells property to kinetis k8x and kv5x
socs. We are now consistently defining this property for all
nxp,kinetis-adc16 compatible nodes.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Allow configuring the clock prescaler divider for the NXP Kinetis
FlexTimer. Setting the prescaler to a lower value allows for much
higher resolution/accuracy for the generated PWM waveforms.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Instead of having a Kconfig property, if there is no local-mac-address
property in the devicetree than we'll generate a unique MAC address
based on unique ID registers on the SoC.
We remove the local-mac-address properties in the SoC dtsi files to
match the default behavior that existed before (ie, unique MAC address)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add infineon xmc series with XMC4500 support. XMC series comes with,
- CPU operates upto 120MHz
- 3 RAM (PSRAM1 - code, DSRAM1 - data and DSRAM2 - communiation)
- upto 1MB flash
init: clock control & gpio is not done, so SoC initialization directly
relies on HAL. Core operating clock is stored in no_init section, which
is kept under DSRAM1. Only DSRAM1 is used until clock support. Using
PSRAM1 and DSRAM1 needs adaptation in linker script - planned for next
revision.
Note: SystemInit cannot be consumed directly due to vector table +
HAL linker dependency.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
This commit adds support for nRF52820 development on nRF52833DK.
Changes afffects:
- Introduce files related to board description.
- Add blank documentation file (for future update).
- configuration files for build process.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
This commit adds basic support for nRF52820 SoC.
Changes affect introducing:
- architecuture files (dtsi)
- configuration of nrfx drivers
- adaptation of inclusions based on chosen SoC
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Add STM32F427. This is mainly aimed towards the stm32f427vi.
Changes:
- Add stm32f427 support based on previous work
done for the stm32f429.
- Rework currunt stm32f429 implimentation to now
be based on stm32f427.
- Introduce dedicated dtsi for the VI variant of both
stm32f427 and stm32f429. This is done to prevent stm32f4.dtsi
from being included twice.
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Update dtsi and pinmux macros for stm32f7 family. Add sdmmc1 to dts file
for stm32f746g_disco. Also add board specific configuration file for
fat_fs sample.
Signed-off-by: Helge Juul <helge@fastmail.com>
Update the dtsi for stm32l471 (which the higher SoCs are based on) to
support the stm32-sdmmc disk access device. Enable the device for the
stm32l496g_disco board, and update the pinmuxing.
Note that the stm32l496g_disco board also has a card detect gpio
(MFX_GPIO8), but this is not supported yet. When not specified the
driver will assume a card is present.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Add initial support for Broadcom Viper SoC.
It has ARM Cortex-M7 and Cortex-A72 cores.
Signed-off-by: Arjun Jyothi <arjun.jyothi@broadcom.com>
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Binding used for LPC random number generator hardware.
Describes RNG device node in LPC5xxx SoCs device tree peripherals.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Add support for ADC on H7 series. Note that ADC1 and ADC2 share the same
register set, so it is added as "adc1_2".
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Convert i2s_sam_ssc driver to utilize devicetree. We replace Kconfig
options for specifying the DMA configuration (channel, DMA device name)
with getting that from devicetree. We also get pincfg from devicetree,
however we still have Kconfig sybmols to specify if the RF or RK pin is
enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert sam_xdmac driver to utilize devicetree. As part of the
controller binding we specify that dmas should contain a channel and the
perid for the DMA transaction.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Once the TPM driver and the required configs have been added,
now this patch enables the usage of the PWM framework on KW41Z
SoCs. As such, the DTS gets the proper nodes and the pinmuxing
is done according to the configuration requested.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
* Define USB driver for base stm32wb device.
* Enable USB for the nucleo_wb55rg board.
* Properly initialize USB power + clock for the platform.
Signed-off-by: Pete Johanson <peter@peterjohanson.com>
Reworked sam_gmac driver to get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from soc_pinmap.h that are no longer needed due to
getting all that information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Atmel SAM D5x and E5x series SoCs include the ARM memory protection
unit that supports up to 8 memory regions.
This commit adds the missing device tree MPU node to `samd5x.dtsi`,
which is used by both the SAM D5x and E5x series SoCs.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This patch is defining the DMA1 & 2 for the sm32l4 series
with 7 channels and support of mem2mem transfers
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add device tree nodes for the Digital-to-Analog (DAC) modules present
in the NXP Kinetis K6x series.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add device tree node for the Digital-to-Analog (DAC32) module present
in the NXP Kinetis KE1xF series.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add initial devicetree for the NXP LPC55S16. Only non-secure (ns)
access is supported for now.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Do not assume in the SoC level device trees that NXP Kinetis FlexTimer
nodes will always be configured as PWM. Instead, configure FlexTimer
nodes for PWM at the board level for NXP Kinetis boards.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks from devicetree.
We add a property ('calib-offset') for the SAM{D,E}5x family of SoCs
that is the bit position offset from ADC0 BIASCOMP in the NVM Software
Calibration Area Mapping. For ADC0 this is typically 0 and for ADC1
this will be 14.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In STM32 can driver CAN2 instance need to know the base address
of CAN1 instance which is referenced as master can.
Add this information as an optional property to stm32 can binding.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
The pinmux_mchp_xec is also being updated since it's using DT
from GPIO.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Replace DT_FLASH_DEV_NAME with DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL.
We now set zephyr,flash-controller in the chosen node of the device
tree to the flash controller device.
NOTE: For a SoCs with on die flash, this points to the controller and
not the 'soc-nv-flash' node. Typically the controller is the
parent of the 'soc-nv-flash' node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add clock references for ADC and TC devices. Update the bindings for
these devices to require clocks property and update the dtsi files to
have the clock info.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add pinctl support for the SAM SPI device. We update the SPI
binding to have pinctrl-0 bindings that are expected to have
at least phandles for MISO, MOSI, and SPCK, but might also have
various chip selects as well.
The pinctrl nodes will have an 'atmel,pins' property that describes the
GPIO port, pin and periphal configuration for that pin.
We update sam*-pinctrl.dtsi files with all the various pin ctrl
configuration operations supported by the given SoC family. These
files are based on data extracted from the Atmel ASF HAL
(in include/sam<FAMILY>/pio/*.h).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add wdt0 node labels for all watchdogs. Keep the existing wdt node
labels in place for backwards compatibility.
Add a wdt1 node to the nRF5340 application core .dtsi, but leave it
disabled. Leave the wdt node's label set to "WDT" on this core for
backwards compatibility also, in case any users are getting it with a
string literal instead of asking the devicetree. This can be changed
later after this round of watchdog changes has been shaken out and
tested more.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The SAM D5x and E5x series SoCs include the "Cortex-M4F" core, not the
FPU-less "Cortex-M4" core.
This commit fixes the incorrect CPU compatible for the SAM D5x and E5x
SoCs (note that this file is included by `same5x.dtsi`, which is used
as the base device tree header for the SAM E5x series).
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Convert driver to use DT_INST_ defines. As part of this conversion we
remove the Kconfig options for per GPIO controller enables and instead
get that information from device tree. This means we now disable each
GPIO controller by default in the DTS and have each board dts enable the
GPIO controller ports it needs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked adc_sam_afec driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the atmel,sam0-dmac binding under the dma binding dir and add
cell information for channel and trigger source. Update the associated
dtsi files to match these changes.
This is in prep of ATMEL SAM0 SERCOMM devices like UART, I2C, and SPI to
user proper 'dmas' property to specify the dma info to use.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the GCLK, MCLK, and PM clock controllers. Add bindings
and devicetree nodes associated with these clock controllers. Also add
clock references for the SERCOM peripheral set to allow those drivers
(i2c, spi, uart) to utilize this information.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit renames `samd.dtsi` to `samd2x.dtsi` since this DTS header
is specific to the SAM D2x series and its derivatives (e.g. SAM R21).
Note that the SAM D5x series uses a different DTS header file (i.e.
`samd5x.dtsi`) due to the vast differences, and the future SAM D1x will
have to use a separate DTS header to be sensible anyway.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
There was a typo bug in the SRAM ranges property that causes the SRAM
nodes to appear at the wrong addresses.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add pinctl support for the SAM TWI and TWIHS I2C devices. We update
the TWI and TWIHS I2C bindings to have pinctrl-0 bindings that are
expected to have 2 phandles to the TWCK & TWD pinctrl nodes.
The pinctrl nodes will have an 'atmel,pins' property that describes the
GPIO port, pin and periphal configuration for that pin.
We update sam*-pinctrl.dtsi files with all the various pin ctrl
configuration operations supported by the given SoC family. These
files are based on data extracted from the Atmel ASF HAL
(in include/sam<FAMILY>/pio/*.h).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Mark all the individual PWMs as disabled in dts and enable the one
explicitly used on the mimxrt1064_evk.dts in the board dts file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add pinctl support for the SAM UART and SAM USART devices. We update
the UART and USART bindings to have pinctrl-0 bindings that are expected
to have 2 phandles to the RX & TX pinctrl nodes.
The pinctrl nodes will have an 'atmel,pins' property that describes the
GPIO port, pin and periphal configuration for that pin.
We add sam*-pinctrl.dtsi files with all the various pin ctrl
configuration operations supported by the given SoC family. These
files are based on data extracted from the Atmel ASF HAL
(in include/sam<FAMILY>/pio/*.h).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The atmel,pins property will be utilized to describe pin mux
configuration. The property will be a phandle-array in which the
phandle points to the given GPIO port the pin is on, the pin number, and
the mux configuration.
This change updates the atmel,sam-gpio binding to support that
phandle-array and updates the associated SoC dtsi files as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the majority of the device tree into nxp_lpc55S6x_common.dtsi and
use ranges to handle the different address may for non-secure.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds a GMAC instance to the SAM E5x device tree, along with
the refactoring necessary to specify the SAM E5x-specific components.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The SAM4E GMAC version can use only MII as phy-connection-type. This
update the current default RMII value to MII.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit adds a GMAC instance to the SAM 4E device tree.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit fixes the incorrect memory (FLASH and SRAM) size
specification in the device tree and the board test yaml files.
The `qemu_cortex_r5` board (using `fdt-single_arch-zcu102-arm.dtb` FDT)
has 64MiB RAM at the address 0 and 32MiB QSPI flash at 0xc0000000.
QEMU `info mtree`:
0000000000000000-ffffffffffffffff (prio 0, i/o): memory@00000000
0000000000000000-000000000002ffff (prio 0, ram): ddr_bank1_1@0x0
0000000000030000-000000000003ffff (prio 0, ram): ddr_bank1_2@0x30000
0000000000040000-0000000003ffffff (prio 0, ram): ddr_bank1_3@0x40000
00000000c0000000-00000000c1ffffff (prio 0, i/o): lqspi
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as spi. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as usart. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as i2c. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The st,stm32l0-flash-controller did not have a binding, add one for it.
Also made a comment in stm32l0.dtsi that the driver doesn't currently
support this controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The flash at 0 is a cfi-flash and its 2 banks each that are 64M.
Update qemu-virt-a53.dtsi to reflect the proper flash config, however we
comment out the second bank of flash for now because zephyr,flash can
only handle one value in the reg property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Group all the GPIO controllers under a pinctl node so that we have a
container for pinmux configuration data.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds i2c device tree bindings and nodes for the lpc54xxx and lpc55s6x
socs in preparation for adding a new i2c driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Make sure every flash controller has a node label "flash_controller".
This will make it easier to refer to the SoC NVMC node when necessary.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Define rng nodes for all SoCs featuring the RNG peripheral,
so that the entropy_nrf5 driver can be converted to DTS.
For the network core in nRF5340, align the RNG interrupt priority with
what is used as the default value in (almost) all other DTS nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Currently supported nRF SoCs featuring the second GPIO port (P1) do not
have all 32 pins implemented in that port. Add the "ngpios" property
in gpio1 nodes for these SoCs, so that they don't take the default
value of 32 to indicate the number of available pins but use instead:
- 10 for nRF52833
- 16 for nRF52840
- 16 for nRF5340 (both application and network core)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the STM32L422Xb SoC. Base stm32l422.dtsi on
stm32l412.dtsi to be able to add the crypto device later.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
64 kB of memory is reserved for the inter-processor
communication. this makes sense only if RPMsg is used.
Allow to use this memory for firmware data by default.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
This commit adds a GMAC instance to the SAM V71 device tree, with the
chip revision-specific hardware queue count.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds a GMAC instance to the SAM E70 device tree, with the
chip revision-specific hardware queue count.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
SIM core system clock is being used, but more importantly this will
enable to get the SIM clock controller in use for power management
purposes in MCUX ethernet driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Added device tree nodes and associated headers for
defined uarts on the stm32g0 and stm32g07x 8x parts.
Tested with uart on stm32g071rb disco board with usart3 going to stlink.
Using shell.
Signed-off-by: Kieran Levin <ktl@frame.work>
The shared irq support isn't needed in this driver. We just need to
deal with the fact that some SoCs have only a single interrupt line and
some have three interrupts. We can just ifdef that based on
DT_NUM_IRQS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert the driver to use DT_INST_ defines, update all dependent dts,
soc and board files.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The `xlnx,ttcps` binding, despite having the file name of
`xlnx,ttcps.yaml`, had the compatible property of `cdns,ttc`.
While it is true that the Xilinx ZynqMP platform embeds the Cadence
Triple Timer Counter (TTC) IP core, its TTC differs from the original
Cadence core in that it implements 32-bit counters, instead of the
16-bit counters defined in the original; hence, the Xilinx variant is
not compatible with the original Cadence version and should be treated
as a different device.
This commit changes the `xlnx,ttcps.yaml` compatible property to
`xlnx,ttcps` for the above reasons.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Add a fixed clock to the qemu-virt-a53.dtsi to match how the musca dts
files work so we get the clock DT info in the same way in the driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add entropy driver based on GECKO TRNG module along with device
tree support for EFM32PG and EFR32MG SOCs.
Signed-off-by: Pooja Karanjekar <pooja.karanjekar@lemonbeat.com>
Convert usb_stm32 driver to use of DT_INST macros.
Since driver is compatible with 3 different dt compatibles and
compatible string is included in DT_INST macros, I've kept the
DT_USB_ compatible agnostic macros based on DT_INST ones, which
allowed to remove fixup definitions.
Use of DT_USB symbols is now limited to usb_dc_stm32.
Additionally, compatible "st,stm32-otgfs" is removed from list
of compatibles for usbotg_hs ips.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On stm32 spi devices, there are 2 main IP variants, with and w/o
fifo. Fifo is not really used today, but still there is some
additional code handling fifo. Today this code is protected under
Kconfig symbol SPI_STM32_HAS_FIFO.
This code carries redundant information vs dedicated compatible
"st,stm32-spi-fifo", which is provided as unique driver compatible
for devices supporting this IP as opposed to use of "st,stm32-spi"
when fifo is not supported.
Having these 2 compatibles defined exclusively is not convenient for
migration to DT_INST as DT_INST macros contain compatible string and
hence it cannot be used to provide common compatible code for devices
defining different compatibles.
Based on these observations, review stm32 spi devices compatible
declarations. Devices supporting fifo will now declare both
compatibles, as proposed by dt spec: "[compatible] property value
consists of a concatenated list of null terminated strings,
from most specific to most general". Hence field will now be:
"st,stm32-spi-fifo", "st,stm32-spi"
This way, fifo enabled stm32 spi devices will generate both:
DT_INST_STM32_SPI_FOO and DT_INST_STM32_SPI_FIFO_FOO
As well as:
DT_COMPAT_ST_STM32_SPI and DT_COMPAT_ST_STM32_SPI_FIFO
So, DT_INST_STM32_SPI_FOO could be used for device initialization.
Also DT_COMPAT_ST_STM32_SPI_FIFO could be used for FIFO handling
code inside driver. Hence use it to replace Kconfig symbol
SPI_STM32_HAS_FIFO.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a property to the nxp,kinetis-gpio binding that related the GPIO
node to the pinmux PORT node.
For the kl25z we add the pinmux nodes as well since they didn't exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enable counter driver support for H7 series. Tested with H743ZI MCU
using samples/drivers/counter/alarm.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Change to code to use the automatically generated DT_INST_*
defines and remove the now unneeded configs and fixups.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Introduction of tachometer device nodes for the Microchip
MEC1501 SOC. In addition, dts bindings for are also introduced.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
LPC55S69 CPU1 definition added.
Dual Core is not enabled!
Definitions related to dual core split of SoC's CPUs.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Add girq and girq-bit to encode per device information. This allows the
driver to get any device unique info from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add girq and girq-bit to encode per device information. This allows the
driver to get any device unique info from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. Replace dts_fixup.h use
for DT_RTC_0_NAME with DT_INST_0_NXP_KINETIS_RTC_LABEL to be
consistent. Also, remove the aliases that had been used for this
driver in various nxp_k*.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines and remove Kconfig per instance
enablement in favor of DT_INST_ define existing. Also, remove the
aliases that had been used for this driver in nxp_rt.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The driver for STM32's independent watchdog already exists and is
compatible with the stm32g0 SoC. Enable the independent watchdog
for the stm32g0 series for use with this driver.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit adds Device-Tree instances of the Flash controller
to the SAM3X, SAM4E and SAM4S series. The Flash-Controller
is used to get the unique device identifier.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
On stm32f302/3 series, USB and CAN_1 share same IRQ lines.
To use USB and CAN_1 together, USB IRQ could be remap to other
line numbers, on which there is no conflict.
Remap the USB IRQ lines by default:
-Assign remap number in matching dtsi files
-Perform remap before usb driver init
Additionally, fix compilation issue in usb driver.
Fixes#22343
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit adds the following:
- EFR32FG1P SoC support for the watchdog
- efr32_slwstk6061a board support for the watchdog
Signed-off-by: Oane Kingma <o.kingma@interay.com>
This commit adds the following:
- EFR32MG SoC support for the watchdog
- efr32mg_sltb004a board support for the watchdog
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
This commit adds the following:
- device tree bindings for Gecko watchdog driver
- EFM32PG SOC support for the watchdog driver
- EFM32PG board support for the watchdog driver
- DTS aliases for testing with default watchdog driver test
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Enable the shared IRQ for the UART line and enable the remaining tasks
that depends on a separated declaration of the TX/RX/Err/... IRQs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This commit adds the remaining gpio ports I, J and K to the device
tree and dts_fixup headers of the EFM32JG12B and EFM32PG12B SoCs.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
The blocks were moved into the soc block in samd5x.dtsi,
so we also have to move them for the the actual SoC definitions
that inherit from that.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
The Silicon Labs EFM32 Jade Gecko MCU includes:
* Cortex-M3 core at 40MHz
* up to 1024KB of flash and 256KB of RAM
* multiple low power peripherals
This is basically the same as the EFM32 Pearl Gecko, but with an ARM
Cortex-M3 core instead of a Cortex-M4F.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
The driver for STM32's independent watchdog already exists and is
compatible with the stm32l1 SoC. Enable the independent watchdog
for the stm32l1 series for use with this driver.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
Most JEDEC NOR flash devices uses not only typical SPI mode
(MISO,MOSI,SCK and CS), but also QSPI mode (IO0,IO1,IO2,IO3,SCK and CS).
QSPI mode uses more data lines and as a result provide higher
throughput. If this were not enough, Nordic chips provide
hardware acceleration for read/write/erase functions, what
gives significant performance boost.
It does a lot of things "behind the scene", i.e when user has written
some data to the flash and would like to read them back, it has to wait
until the flash is ready by reading WIP bit in Status Register.
This driver does it automatically.
Signed-off-by: Kamil Lazowski <Kamil.Lazowski@nordicsemi.no>
Update the hal_nordic module revision, to switch to nrfx 2.1.0.
Because the list of peripherals for nRF5340 has changed as follows:
- SPIM2 has been renamed to SPIM4
- SPIM2-3, SPIS2-3, TWIM2-3, TWIS2-3, and UARTE2-3 have been added
a couple of related corrections needed to be applied in dts and Kconfig
files, plus the spi_nrfx_spim driver has been extended with the support
for SPIM4.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This checks if the DMA controller supports or not
the memory-to-memory transfers. For DMA Version1,
in the stm32f2xx, stm32f4xx, stm32f7xx series,
only DMA instance 2 is able to transfer mem-to-mem.
For other series, with DMA Version2, there is no such a limitation.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit adds initial support for the Silicon Labs EFM32
Giant Gecko GG11 StarterKit.
Features supported for now are NVIC, SysTick, GPIO, Flash,
Counter, I2C, UART and Ethernet. Support for Watchdog and
ADC will follow as soon as their respective PRs are merged.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Currently, only the stm32h747 soc is supported in the h7 foler.
The h7 series comes with both single core and dual core products.
This change moves C-M4 core out of stm32h7.dtsi so that it can be
included by single core STM32H7 soc description.
Signed-off-by: Moonkwun Jung <mkainyh@gmail.com>
Fix the RTC device tree node for the NXP K6x SoC series. This device
is compatible with nxp,kinetis-rtc.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
STM32L073 soc variant is a STM32L072 with LCD peripheral.
Reflect this in dts definition by including stm32l072.dtsi
in stm32l073.dtsi.
This also allows to fix an issue on stm32l073 gpioe which
declared wrong reg definition.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The I2C controllers on the MEC1501 SoC can be attached to
different I2C output line. For example, the I2C #0 controller
can be used with I2C7 physical lines out of SoC. The output
selection is done by the attribute "port_sel". This renames
the parent I2C nodes on the SoC side to refer to
the controller themselves instead of the output lines to
avoid confusion. The labels of these nodes are also renamed
to reflect the controllers.
On the board level, the DTS labels are overwritten to indicate
the actual output lines.
Aliases are also provided in both SoC and board levels to
provide shortcuts to the DTS nodes.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The SoC, driver, and board support for the CC2650 and CC2650 Sensortag
aren't currently supported and we are removing them as such. If anyone
is interesting in supporting this platform we can easily recovery it
from git.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree nodes for the internal temperature sensor in the NXP
Kinetis K6x SoC series.
A temperature sensor node is added for each ADC in the SoC to allow
the user to choose which ADC instance to use for the sensor readings.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add device tree nodes for the internal temperature sensor in the NXP
Kinetis KE1xF SoC series.
A temperature sensor node is added for each ADC in the SoC to allow
the user to choose which ADC instance to use for the sensor readings.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Added dts additions for stm32 nucleo f767zi board, also added
and modified soc addtions for thet board.
Updated dts reference file name.
Updated yaml to take out adc for now.
Signed-off-by: Roland Ma <rolandma@yahoo.com>
The amount of lock regions differs between different sam0 MCUs.
saml10: 2
saml11: 4
samd2x: 16
saml2x: 16
samd5x: 32
ASF does not provide a definition for this, so create a new one
in dts.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Refactors the mcux gpt driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all lpc socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all i.mx 6/7 socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all i.mx rt socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all kinetis socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add device_type DTS property in sram0 and sram1 nodes,
for nRF5340 Application and Network CPU, respectively.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add support for specifying PWM flags for the NXP Kinetis FlexTimer
(FTM) PWM driver through the device tree.
All in-tree clients of this PWM controller are active-low LEDs.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit fixes the following problems with the RPU device tree:
1. The core type of the RPU of ZynqMP SoC is Cortex-R5F, not
Cortex-R4.
2. RPU and APU use different interrupt controllers (PL390 GICv1 and
GIC-400 GICv2, respectively) mapped to the same CPU local bus address
region but with different offsets for the distributor and CPU
interrupt control register sets. The GIC address mapping specified by
the current dts is that of an APU and does not apply to the PL390
GICv1 of an RPU (refer to the "Zynq UltraScale+ Devices Register
Reference" document from Xilinx for more information).
For more details, refer to the issue #20217.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
ZynqMP SoC embeds two separate processor types: Cortex-R for RPU and
Cortex-A for APU.
Since the current Zephyr architecture cannot support AMP of Cortex-R
and Cortex-A within one project, the RPU and APU should be considered
separate platforms.
This commit relocates the device tree nodes that are not common between
RPU and APU to a separate dtsi file (zynqmp_rpu.dtsi).
When Cortex-A53 APU support is added in the future, an additional dtsi
file (zynqmp_apu.dtsi) for specifying the APU device tree should be
added.
For more details, refer to the issue #20217.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Rename the NXP FTM instances in the KE1xF SoC to PWM to match the
other SoCs/boards using the FlexTimer as PWM generator.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This patchset enables USART3 on the 96Boards STM32 Mezzanine.
It is broken out to J10 Grove Connector.
Changes:
- Enabled USART3 in board dts.
- Updated board index.rst with uart pinouts.
- soc dtsi: enabled usart3.
Test: Tested USART3 as console at 115200 baud
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
This patch enables SPI4 on the 96Boards STM32 Sensors Mezzanine.
SPI4 has been broken out to a Grove Connector on the board.
Changes:
- Updated board dts to enable spi4
- Updated board Kconfig
- Updated board documentation
- Update board pinmux
- Updated stm32f4 pinmux header file
- Updated stm32f401 dtsi
- Updated stm32f4 defconfig to enable PORTE GPIO
- Added board to spi_loopback test
Test: spi_loopback test passed
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Adds spi device tree bindings and nodes for the lpc54xxx and lpc55s6x
socs in preparation for adding a new spi driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The GIC-400 driver currently only supports SPIs because the (32) offset
for the INTIDs is hard-coded in the driver. At the driver level there is
no really difference between PPIs and SPIs so we can easily extend the
driver to support PPIs as well.
This is useful if we want to add support for the ARM Generic Timers that
use INTIDs in the PPI range.
SPI interrupts are in the range [0-987]. PPI interrupts are in the range
[0-15].
This commit adds interrupt 'type' cell to the GIC device tree binding
and changes the 'irq' cell to use interrupt type-specific index, rather
than a linear IRQ number.
The 'type'+'irq (index)' combo is automatically fixed up into a linear
IRQ number by the scripts/dts/gen_defines.py script.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add device tree elements for all gpio ports of the efr32mg12p including
the dts fixup entries.
Also remove gpio port e since this is not available in efr32mg12p socs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
NXP's LPC family of MCU's GPIOs parameters is udated.
Boards LPC54xxx and LPC55xxx have updated values according
pin and interrupt layout.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
This commit adds basic support for nRF52833 SoC.
Changes affect introducing:
- architecuture files (dtsi)
- configuration of nrfx drivers
- adaptation of inclusions based on chosen SoC
- configuration of NFCT_PINS_AS_GPIOS depends on HAS_HW_NRF_NFCT.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This patch introduces the support of the Low Power Timer
for the STM32WBxx from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The SPI NOR driver requires that the size (in bits) be provided in the
devicetree node. Update the binding to make the property required,
and update all nodes based on the memory chip identified.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This patch introduces the support of the Low Power Timer
for the STM32L4xx from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds supoprt for the Atmel SAME54 SoC.
The SAME5x/SAMD5x is a line of Cortex-M4F MCUs that share peripherals
with the sam0 Cortex-M0+ and saml1x Cortex-M23 parts.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Introduce a standard watchdog alias 'watchdog0' that can be utilized
by sample/test code in the future. This helps remove the need for
CONFIG_WDT_0_NAME in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
dts pinctrl definitions were pushed in tree without the code
available to deal with it. They have been kept waiting for the
code, but this is taking much more time than initially thought.
So in current zephyr tree, for all STM32 boards, we have pinmux.c
file which is used to configure pins and these files that are
basically no-op. This situation is creating a lot of confusion
especially to new comers, and create useless maintenance effort.
Remove these files for now.
When zephyr will ready to use them, this commit could be reverted.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit moves DMA parameters previously hard coded in the driver
to the dts.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There is no APB2 bus on stm32f0 series.
What could be found as APB2 in CMSIS files is actually
second group of APB (A.K.A APB1_2).
Fix nodes that are using this wrong reference accorss the series.
Fixes#20310
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move the selection of the IP clock source for the modules in the NXP
Kinetis KE1xF SoCs from being hardcoded in soc.c to being specified in
the device tree.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
STM32L151XB-A SoC is almost similar to the STM32L151XB SoC except that
it has more RAM (32KiB). Hence add devicetree and Kconfig support.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Indtroduction of generic device tree bindings for keyboard scan devices.
In addition, device tree node entries and dt specific bindings where
also implemented for Microchip MEC1501
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
STM32L1 uses the same spi controller as STM32F1 so we can just set the
right addresses and enable them. We also need to add the fixup names and
to correctly include the header for ST LL HAL.
Signed-off-by: Karl Palsson <karlp@etactica.com>
1. Replace the non-existent CPU device binding ("Cortex-R") specified
by the CPU node with a proper one.
2. Relocate CPU node declaration to SoC dtsi:
The CPU node should be declared in the SoC dtsi because the core
type is SoC-dependent. In fact, this is exactly how it is done in
the Cortex-M port.
3. Remove core_intc (supposedly Cortex-R VIC):
Unlike the NVIC of Cortex-M, the VIC of Cortex-R is not a true
interrupt controller in the conventional sense and merely acts as
a CPU input port for aggregated interrupt request and vector index
signals. For this reason, there is no point in declaring it in the
device tree and specifying it as an interrupt parent. All SoCs
incorporating Cortex-R implement a separate true interrupt
controller (for instance, GIC for Zynq MPSoC and VIM for Hercules).
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The patch adds initial support for STM32F030X4 SoC.
STM32F0 Cube package advises to use 'stm32f030x6' code
for both STM32F030x4 and STM32F030x6 SoC variants.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Add soc and dts files to support for most of the common peripherals
in the STM32G4 series. Add specific support for the STM32G431RB.
Signed-off-by: Richard Osterloh <richard.osterloh@gmail.com>
Add #pwm-cells property in bindings for Nordic PWMs and add this
property with a suitable value assigned to all PWM nodes in dts
files for Nordic SoCs.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit introduces separate "compatible" strings for DTS nodes
representing different types of Nordic SPI peripherals. Previously
"nordic,nrf-spi" was used for both SPI and SPIM. SPIS was already
handled separately.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/spi/
new binding for "nordic,nrf-spim" is added and common fields for all
3 types of Nordic SPI peripherals are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in spiX nodes are updated (when there is no
choice as only one type of SPI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/spi/
spi_nrfx_spim driver is updated with the new form of macros generated
from dts
* boards/
all spiX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of SPI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (SPI_x_NRF_SPI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit introduces separate "compatible" strings for dts nodes
representing different types of Nordic TWI peripherals. Previously
"nordic,nrf-i2c" was used for both TWI and TWIM, and TWIS was not
supported.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/i2c/
new bindings for "nordic,nrf-twim" and "nordic,nrf-twis" are added
and the one for "nordic,nrf-i2s" is renamed to "nordic,nrf-twi",
common fields for all these bindings are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in i2cX nodes are updated (when there is no
choice as only one type of TWI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/i2c/
both flavors of i2c_nrfx drivers are updated with the new names of
macros generated from dts
* boards/
all i2cX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of TWI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (I2C_x_NRF_TWI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the device tree to assign the correct peripheral clock to each
UART/USART/LEUART. Previously, the clock identifier was determined
through the sequence number of the instantiated UART. This meant
configuring all UARTs when only one of the later UARTs was required.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
This adds support for Kinestis K22
Co-authored-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Co-authored-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Co-authored-by: Tom Burdick <thomas.burdick@gmail.com>
Signed-off-by: Tom Burdick <thomas.burdick@gmail.com>
Add RTC timer driver for CC13X2/CC26X2, and use it instead of systick
as system clock. It is necessary to use this timer for power
management support, so that the system can exit from deep sleep upon
expiry of timeouts.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
4 are found: 2 with a counter of 16bits and 2 with a counter of 32 bits.
However, first 32bits instance will not be exposed as it will be used by
rtos timer driver directly to implement k_busy_wait()
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The driver for STM32's independent watchdog already exists and is
compatible with the stm32wb SoC. Enable the independent watchdog
for the stm32wb series for use with this driver.
Signed-off-by: Robert Weber <robertweber95@gmail.com>
The KE1xF SoC family SIM unit differs from the other Kinetis family
SoCs. Add a unique compatiable and binding for it.
Fixes#18160
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For quite a few peripherals that are currently supported by nrfx HALs
or drivers there are no definitions of corresponding CMSIS-Core
peripheral accessing symbols that would provide their base addresses
in the proper domain (secure or non-secure), accordingly to the build
target. This commits adds devicetree nodes for these peripherals so
that their base addresses can be used in definitions of the accessing
symbols mentioned above.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Pull out the LPO fixed-clock that is part of the PMC hardware block as
its own child node of the PMC block. This is because the PMC could have
its own driver associated with it that is seperate from the LPO clk.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update the ADC bindings to include #io-channel-cells and update the
related dts files to set #io-channel-cells.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
'interrupt-parent' should contain just the phandle of the node
interrupts are sent to.
This node (gic: interrupt-controller@f9010000) doesn't generate any
interrupts, so the 'interrupt-parent' value is never used (this is why
it wasn't caught). It'll give an error later with 'interrupt-parent'
declared as 'type: phandle' in bindings though.
Don't know what was intended. Just remove the 0.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
SPI3 clock info were missing and following macros were
not generated:
- DT_ST_STM32_SPI_FIFO_40003C00_CLOCK_BITS
- DT_ST_STM32_SPI_FIFO_40003C00_CLOCK_BUS
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit adds support for the Zynq UltraScale+ MPSoC as a qemu based
platform for Cortex-R based testing. This SoC only supports an
interrupt controller and serial port for limited testing.
Signed-off-by: Bradley Bolen <bbolen@lexmark.com>
Remove unused "system-clock-frequency" property, we don't have this
defined in various bindings and thus aren't using it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use clock specified in the device tree for obtaining the source clock
frequency for the pwm_mcux_ftm driver instead of relying on having an
NXP Kinetis MCG clock available in all SoCs supporting FlexTimer (FTM)
modules.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
NRF_UICR needs to be defined for nRF9160 SoC in
nrfx_config_nrf9160.h, because it is not defined
in nrfx/hal/mdk/nrf9160.h (as it is a Secure-only
peripheral).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
With the new DT checks the dts bindings for "nxp,flexpwm" and
"nxp,imx-pwm" had old conventions that we now treat as build errors.
Additionally fix the number of #pwm-cells for "nxp,imx-pwm" to be 1.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
i.MX RT10XX processors have four eFlexPWM modules, each containing
four 2-channels PWM submodules.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The true mmio-sram nodes should not have had a 'device_type' property.
Remove it from the cases that we clearly know are SRAM.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These are not declared in dts/bindings/arm/nxp,kinetis-sim.yaml and do
not generate any output.
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
A minor spelling fix in an inline comment in
both nRF9160 Secure and Non-Secure .dtsi headers.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
These are not declared in any binding and do not generate any output.
Trying to get rid of properties that appear on device tree nodes but
aren't declared in bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fix the following dtc warning:
mimxrt1064_evk.dts.pre.tmp:78.31-85.5: Warning (spi_bus_bridge):
/soc/flexspi1@402a4000: node name for SPI buses should be 'spi'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Several aliases were added to nrf9160[ns].dtsi files solely for
the purpose of getting base addresses of certain hardware modules
via DT_ macros generated for these aliases.
Since for one-instance modules the same can be now achieved with
standard DT_INST_0_* macros, there is no need to keep these aliases.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
pinmux: Add the relevant definition of the spi3 pin
dts: Fix a bug, spi3 does not have a label
soc: Supplement spi3 related definition
Signed-off-by: Findlay Feng <i@fengch.me>
stm32f429.dtsi wrongly introduced i2s nodes 4, 5 and 6.
Remove them as actually only i2s nodes 2 and 3 are supported on
these socs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a kernel timer driver for the MEC1501 32KHz RTOS timer.
This timer is a count down 32-bit counter clocked at a fixed
32768 Hz. It features one-shot, auto-reload, and halt count down
while the Cortex-M is halted by JTAG/SWD. This driver is based
on the new Intel local APIC driver. The driver was tuned for
accuracy at small sleep values. Added a work-around for RTOS
timer restart issue. RTOS timer driver requires board ticks per
second to be 32768 if tickless operation is configured.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
This was always intended to be a bytestring rather than an array, but
full support was missing. Since that has been addressed switch it to
the preferred format.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The property is required on all SPI clients, but was missing from
several devicetree nodes. Set it, using the capitalized version of the
node alias when present, with "jedec,spi-nor#0" as the fallback.
Closes#17662
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Have the SoC dtsi files for microchip mark the devices (uart & i2c) as
disabled by default and let the board dts files enable which one's they
need/use (which is what's happening already).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
spi-max-frequency is marked as required in
dts/bindings/mtd/jedec,spi-nor.yaml.
I took the value from the datasheets (133 MHz for all), and guessed that
a dummy entry is fine for QEMU.
Fixes some errors in
https://github.com/zephyrproject-rtos/zephyr/issues/17532.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
There doesn't seem to be any use of the virtualcom device in the code,
so lets remove it from the dts as it describes itself as a usb device
controller which it is not.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds a fixed clock node (representing clock driving
system bus). The added node is then referenced by peripherals requiring
information about driving clock frequency.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
This commit adds 'clock-frequency' property to the cpu nodes.
The clock frequency specified in the added property is used
during platform configuration. Examples:
- The SWO logger uses clock frequency to configure SWO output.
- Plenty of platforms need CPU clock specified for their HAL.
- Most of devices with USB needs information about CPU clock
in order to configure USB clock source.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
This patch populates "clocks" property in stm32 usb nodes
for clock related usb configuration code of each dtsi files
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The spi-nor flash nodes require a jedec-id property as per the binding.
We add the jedec-id's as best we can determine based on the data sheets
for the various flash modules on these boards.
However these id's should be validated by actually reading the value to
ensure they are correct.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix USB phy node for stm32l432 and stm32l452, which contain
a USB controller and not a OTG FS controller.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
1) dts/bindings/mmc/mmc.yaml: specifies common mmc.
2) dts/bindings/mmc/nxp,imx-usdhc.yaml: specifies
nxp usdhc module which inherits mmc.
3) dts/arm/nxp/nxp_rt.dtsi: usdhc support on RT chip.
4) boards/arm/mimxrt1050_evk/mimxrt1050_evk.dts:
usdhc slot support on mimxrt1050_evk board.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
A number of minor issues with the 'fixed-clock' support:
* Fix the #clock-cells to be 0
* Fix nxp_ke1xf.dtsi to set #clock-cells 0 and the clock reference to
only be a phandle.
* Fix the generation script to only generate what it should for a
'fixed-clock'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add clock support for STM32G0X SoC series.
Signed-off-by: Philippe Retornaz <philippe@shapescale.com
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patch adds support for the STM32G071xx
from STMicroelectronics.
Signed-off-by: Philippe Retornaz <philippe@shapescale.com>
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Allow individual specification of the time quanta used for the CAN bus
propagation segment and phase segment 1.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Added support for the STM32L496XE series with 512KB internal flash and
256KB SRAM of contiguous addresses.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit adds counter driver based on RTCC module for SiLabs Gecko
SoCs.
Tested with SLWSTK6061A / BRD4250B wireless starter kit.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
stm32wb55rg is a dual core SoC (M4/M0) with a radio/protocol stack
running on M0 core. M0 FW starts at flash address 0x80CB000.
So flash size available to zephyr is 812K instead of 1M.
Configure package size to reflect this (flash size is now 812K)
and update MPU setting to exclude M0 FW. From MPU point of view,
we set flash size to 512K since we should chose a size being a power
of 2.
If we consider there will be 2 images partitions in a FOTA scheme,
512 K is beyond image-0 and hence is sufficient to cover application
image.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
sram2a and sram2b where defined in the prospect of defining
HCI shared memory sections from device tree.
Remove them, since this is not the case anymore.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This adds support for the basic timer counter (TC) found on SAM0
series parts. This driver only supports running the counter
in 32 bit wide mode. Since this mode explicitly slaves the odd
counters to the even ones, only instances of the even ones are
defined.
Tested with tests/drivers/counter/counter_basic_api on SAMD21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add support for the Low Power Inter-Integrated Circuit (LPI2C)
controllers found in the NXP Kinetis KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The node name for device_id was device_id@0 it should be
device_id@80a00c to reflect the first register region
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
ARM SysTick peripheral is optional in Cortex-M0 MCUs,
so we delete the respective dts node when the peripheral
is not present.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Atmel SAM D series SoC variants (present in the tree) all have
an ARM Cortex-M0+ core, not a Cortex-M0, so we correct this in
the .dtsi header.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Unlike Cortex-M3 and Cortex-M4, in Cortex-M7 the number of
MPU regions may vary based on the implementation. This commit
adds a DTS node for the ARM MPU peripheral in the device tree
of Cortex-M7 SoCs and updates the fixup files, so we may extract
the number of MPU regions at build time. SoCs:
- nxp_rt
- same70
- stm32f7
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds a DTS node for the ARM MPU peripheral in the
device tree of ARMv8-M SoCs (for the secure and the non-secure
DTS descriptions) and updates the fixup files. SoCs:
- nrf9160
- musca_a
- musca_b1
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Adding missing erase-block-size entries for the flash-controller
nodes in the nrf52810 and nrf52811 .dtsi files.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Move flash-controller and SRAM node definitions under SoC node.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Reduced Kconfig for counter with nRF TIMER and RTC. Added overlays
for TIMER and RTC configuration in the counter test.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit adds basic support for nrf52811 in the arch SoC, dts
and nrfx folders.
The nRF52811 is a Bluetooth 5.1 Direction Finding SoC with comprehensive
protocol support.
The nRF52811 SoC is capable of the latest features of Bluetooth 5.1,
the most prominent being Direction Finding.
The radio in the nRF52811 SoC has comprehensive protocol capabilities,
including Bluetooth 5.1 Directing Finding, all Bluetooth 5 features,
802.15.4, Thread, Zigbee, ANT and 2.4 GHz proprietary.
It has 4 dBm TX power and has been optimized to offer the best RX
sensitivity of all SoCs in the nRF52 series.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
add usbd1 definition to rt dts file,
set EHCI controller config default value in rt1050 default config file,
add EHCI controller driver MACROs to dts_fixup.h,
initialize EHCI clock in rt soc.c
add HAS_MCUX_USB_EHCI for supported soc in Kconfig.soc
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
Dts Nodes for all the GPIO portswere defined. In addition,
a new binding file was created for the gpio driver.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Expose MEC1501 5 I2C/SMB controllers
Add Microchip specific I2C device tree properties
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
All series of stm32 have at least one ADC instance and this commit adds
one ADC node to the root dts file of each soc, and also adds fixing up
mappings to them.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
This adds interrupt support to the SAM0 GPIO driver. This is heavily
inspired by @nzmichaelh work in #5715. The primary difference
from that implementation is that here the External Interrupt
Controller (EIC) is separated out into an interrupt controller driver
that is less tightly coupled to the GPIO API. Instead it implements
more of a conversion from the EIC's own odd multiplexing to a more
traditional port and pin mask IRQ-like callback. Unfortunately,
through the EIC on the SAMD2x are relatively well behaved
in terms of pin to EIC line mappings, other chips that share the
peripheral interface are not. So the EIC driver implements a
per-line lookup to the pin and port pair using definitions extracted
from the ASF headers.
The EIC driver still makes some assumptions about how it will be used:
mostly it assumes exactly one callback per port. This should be fine
as the only intended user is the GPIO driver itself.
This has been tested with some simple programs and with
tests/drivers/gpio/gpio_basic_api on a SAMD21 breakout and an
adafruit_trinket_m0 board.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds a SERCOM I2C driver for SAM0 series chips.
Tested with a SAMD21 chip on a SSD1306 display and a MLX90393
sensor. Only compile tested for SAMD20 and SAMR21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add initial support for the TI CC13x2 / CC26x2 series with the CC2652R
and CC1352R SoCs. The UART and GPIO peripherals are supported. Drivers
use the driverlib HAL from the TI CC13x2 / CC26x2 SDK.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Implementation of pinmux for the stm32mp157c_dk2 board.
Some UART pin mux definition has been added (mainly for
UART console and UART/SPI Arduino shield support).
This can be completed with pin mux for other stm32mp157c
UART.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for stm32mp1 basic UART API with Zephyr.
UART Console and UART shell are also supported.
Async UART API and USART support is to be done.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Move SERCOM peripherals to use the raw defines generated from DTS
parsing. This adds aliases to the DTS so that the SERCOM number
can still be used for clocking and pinmux.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds support for the SAM0 DMA Controller (DMAC). Chained
transfer are not currently implemented.
Tested with tests/drivers/dma/loop_transfer and custom modifications
to that test using three parallel reloading channels. Also tested
with a trivial program that did memory->serial.
Signed-off-by: Michael Hope <mlhx@google.com>
[hageman@inthat.cloud: Rebased and updated commit message]
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Initial support for Microchip MEC1501 series is added to the tree.
Additional support for UART is also included. This SoC supports
two operational modes for interrupts (Direct and Aggregated). For
this commit, the direct capable interrupts are configured in
direct mode.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Adds Atmel SAMR21 soc which is based on SAMD21, but with a AT86RF233
radio connected internally via SPI.
The AT86RF233 is not yet supprted by Zephyr at this point.
This code is very much copy & paste from atmel_sam0/samd21
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Add USART1 and LPUART1 nodes on stm32wb series.
Only these 2 ones are available for now on this series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add GPIO support to stm32wb series.
Only ABCDE and H ports are available for now on this series.
Accordingly, update series dtsi file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support to stm32wb series in stm32 clock_control driver.
Ip is similar to stm32l4 one but AHB bus presacler is renamed
to "CPU1" and CPU2 and AHB4 prescalers should be defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add driver support for Atmel SAM0 device ID, which is 16-bytes long.
The device ID can simply be read from memory at a known location, but
the location is only described in the data sheet, not in ASF.
For SAMD2x it's 0x0080A00C, 0x0080A040, 0x0080A044 & 0x0080A048.
For SAMD5x it's 0x008061FC, 0x00806010, 0x00806014 & 0x00806018.
This adds a new property to the device tree to define the device ID
registers for this SoC family.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This commit adds CAN support for nucleo F746zg.
Furtermore CAN was added in stm32f7.dtsi and pinmuc_stm32f7.h
CAN_RX: PD0, CAN_TX: PD1
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
2 identical packages were defined for stm32f412 SoC, invariant "g".
Merge them in new sinclge stm32f412Xg.dtsi.
Update matching boards accordinlgy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
SAMD20 does not have the DMA or USB peripherals and as a result
the IRQs for all subsequent lines are shifted down from SAMD21.
This splits the interrupt assignment for the SERCOMs into the
SoC specific DTS file and moves the USB definition to SAMD21 only.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Ports B and C share a common interrupt vector on kw40 and kw41z socs,
but we don't currently have a way to express this in device tree. A
check was added in commit 77cb942a97 that
correctly causes build errors on kw40/41 boards when both ports are
enabled.
Disable the port b interrupt for now until we have a better way to
handle this.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
According to nrf51 and nrf52 specifaction every peripheral is
assigned a fixed block of 0x1000 bytes. Due to that dts for
nrf51 and nrf52 chips have been updated.
The only exception is gpio for nrf52840 where gpio0 and gpio1
share the same memory regions. For this reason, the definition
of gpio for nrf52840 is different from the others.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
On various stm32 soc packages CCM is available and SRAM size
mentionned in datasheet include CCM.
Though, actual SRAM size defined in dtsi files should not
include CCM sizes.
Fix this on impacted dtsi files.
Fixes#14779
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The iMX RT1060 and RT1064 have additional dedicated 512KB on-chip ram.
This OCRAM2 is mapped at 0x20200000, formerly OCRAM1 (flexram) mapping
which is moved to 0x20280000 in order to guarentee global OCRAM memory
continuity regardless OCRAM1 size configuration (256KB by default).
In default configuration, this gives 768KB (512+256) on-chip ram:
0x20200000 to 0x202BFFFF.
OCRAM2: 0x20200000 - 0x2027FFFF
OCRAM1(FlexRam): 0x2028FFFF - 0x202BFFFF
Add this memory region as a single node in the rt1060 device tree.
Note: MPU expects power of two memory region, in case of 768KB, let
the MPU configure 1MB instead.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
uart4 is not available on whole stm32f4 series (not on stm32f401
for instance), remove from stm32f4.dtsi
It is actually correctly defined in f405, f413 but missing in f446,
so add it in there.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
1. SW PWM device node added to common nrf5_common.dtsi
2. SW PWM node set in all nRF5x DTSI files.
Different initial settings for nRF51 and nRF52 devices.
Status is ok by default for nRF51.
3. Added yaml binding for Nordic SW PWM node.
4. Set codeowner of nordic dts bindings to @anangl
Signed-off-by: Gaute Gamnes <gaute.gamnes@nordicsemi.no>
In the recent MDK brought by nrfx 1.6.2, these legacy peripherals have
been revealed as available also in nRF52810. This patch allows their
use in Zephyr drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
On currently supported stm32f3 chips,
erase-block-size = 2048
write-block-size = 2
Set these property in stm32f3 series root dtsi file.
Fixes#9686
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add nvs support to nucleo_f091rc board. This requires to
add erase-block-size property to stm32f0.dtsi.
Storage partition is set to 4kb at the end of the flash.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Initial support for Microchip MEC1701 series is incorporated to the
tree. Additional support for UART is also included. This SOC supports
two operation modes for interrupts (Direct and Aggregated). For this
commit, the interrupts are configured in direct mode.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
This patch adds basic support for the PWM devices available on the Atmel
SAM family. Beside enabling the driver, everything is selected through
the device tree, including enabling the PWM0 and PWM1 devices. Thus
CONFIG_PWM_0 and CONFIG_PWM_1 are ignored.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add EPIT (Enhanced Periodic Interrupt Timer) peripheral support
for i.MX6SoloX soc.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Adds device tree bindings for the imx enhanced LCD interface (eLCDIF)
controller. The compatible is reused from linux.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Actually, add the "status" property that enables the nodes explicitly.
They were apparently enabled by default without this property.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add sam0_rtc_driver that implements system timer API on top of the RTC
and can be used as a replacement for the default systick timer.
Signed-off-by: Martin Benda <martin.benda@omsquare.com>
This commit introduces the possibility to have multiple
device nodes attached to the same I2S controller. For this
purpose a new i2s-device.yaml description has been introduced
with the a 'reg' property to define the logic number of the
device. For example, if two microphones are attached to the
same I2S port (say 1) to achieve stereo audio, the two microphones
might be described in dts as:
&i2s1 {
status = "ok";
mic@0 {
compatible = "...";
reg = <0>;
label = "...";
};
mic@1 {
compatible = "...";
reg = <1>;
label = "...";
};
};
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Added UART4 alternate pin function for L4 µC for PC10 and PC11.
Corrected naming of previously defined UART4 TX and RX defines.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
The SPI1 controller that is connected to the mcr20a block utilizes the
hardware chipselect and not a GPIO CS. So remove the cs-gpios property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SPI0 node had a property called 'cs' which wasn't used or defined as
part of the binding yaml. So let's remove it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get warnings from dtc when building any of the NXP i.MX-RT boards of
the form:
mimxrt1020_evk.dts_compiled: Warning (simple_bus_reg):
/soc/random@400CC000: simple-bus unit address format
error, expected "400cc000"
Simple fix to make everything lowercase to have the unit-address and reg
match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds STM32 L452 soc with L452xC variant. L452 has 160 KB SRAM;
therefore, mpu mem config has been extended; IRQ number is based on
'stm32l452xx.h'.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Use the symbol generated from DT so that it is common for nRF9160
and nRF5 family SoCs. To avoid artificial renaming of CLOCK_POWER_IRQn
to POWER_CLOCK_IRQn.
For nRF5 family SoCs clock nodes were not defined so far, thus they are
added so that the proper DT symbol is generated for them as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add missing node for instance 0 of the RTC peripheral and use an alias
to the flash-controller node instead of the nvmc node definition (there
is no need to have a separate node just to get the NVMC base address).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Fix the QSPI and hyperflash nodes to be proper SPI children and expose
the address range for direct access as part of the controller's reg
region.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the TRNG device contained in the i.MX RT SoCs. It uses
the existing MCUX driver, and mostly consists in adding the Kconfig and
DTS entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
By default, after reset SWO signal is not connected to GPIO pin.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By default, after reset SWO signal is not connected to GPIO pin. This
commit adds required initialization code to enable support for SWO
logger. Not all SoC series support the feature.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
* Add DTS support for gpio controller driver
Signed-off-by: Ashokkumar B <ashokkumar@zilogic.com>
Signed-off-by: Subash G <subash@zilogic.com>
Signed-off-by: Vishnu K <vishnu@zilogic.com>
Signed-off-by: Vaishnavi D <vaishnavi.d@zilogic.com>
By adding 'aliases' node in SoC .dtsi file it is possible to generate
DT_ defines which specify a logical name rather than relay on module
location on APB bus. E.g. DT_SILABS_GECKO_USART_40010000_LABEL becomes
DT_SILABS_GECKO_USART_USART_0_LABEL. Thus it is possible to remove
dts_fixup.h defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add uart5 nodes to stm32f1 series dts.
Provide matching dts_fixup add-on.
Signed-off-by: Chen Han <qq1433255094@outlook.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit introduces the main device tree header files (.dtsi)
for Nordic nRF9160 SOC, for both Secure and Non-Secure domains.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We only need to add the reg property in flash0 and sram0,
in the different DTS headers for the nRF SOCS. We do not
seem to need to define the nodes again. This commit applies
this simplification for flash and sram sizes definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Fix the following warning that shows up in some NRF device tree files:
Warning (simple_bus_reg): /soc/pwm@4002D000: simple-bus unit
address format error, expected "4002d000"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On i.mx6/7 the TCMU and TCML regions are specific to instruction or
data. So use the nxp,imx-itcm for TCML and nxp,imx-dtcm for TCMU.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The imx-rt-{i,d}tcm bindings can actually be utilized on the i.MX6/7 as
well for the TCM{L,U} regions of memory as they are specific to
instruction or data.
So let's rename imx-rt-{i,d}tcm to imx-{i,d}tcm.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Due to a bad timing in merging PR #10744 and PR #12083, the flash0 node
in stm32f756Xg.dtsi ended-up at the root of the device tree, while the
flash0 node it is trying to override in stm32f7.dtsi is now under
/soc/flash-controller.
This patch fixes that by moving it at the right location.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Added board definitions for nucleo_f756zg. Features include gpio,
pinmux, uart (ST Zio, ST-Link and Arduino Uno v3 interfaces).
Added basic documentation and some soc definitions for the
stm32 f756XX soc.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Adds a second sram node to the k64 device tree to acknowledge that the
additional sram is present in hardware, but deliberately not used in
zephyr until an outstanding issue is solved. The upper and lower sram
nodes are contiguous in the memory map, however the Cortex-M4
architecture does not support misaligned accesses across the boundary
between the two nodes.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds a flash driver for the STM32F7x series, inspired from
the STM32F4x one. It has been tested on the STM32F723, but should also
work on other SoCs of the family.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We currently get a number of warnings like:
Warning (simple_bus_reg): /soc/otgfs_phy: missing or empty
reg/ranges property
This is due to the usb phy nodes not have a reg property since they
don't have an mmio address associated with them.
Move the phy nodes out of the SoC node so their lack of a reg property
will not cause a warning. This is similar to how Linux dts files
handle the phy nodes.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the following warning that shows up in some NRF device tree files:
Warning (simple_bus_reg): /soc/pwm@4001C000: simple-bus unit
address format error, expected "4001c000"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
1. PWM device node added with alias to all
nRF52x DTSI files. 1 instance for
nRF52810, 3 instances for nRF52832, and
4 instance for nRF52840.
2. Added yaml binding for Nordic PWM node.
Signed-off-by: Gaute Gamnes <gaute.gamnes@nordicsemi.no>
Add comptiable into the device tree and associated binding files for NXP
i.MX RT ITCM/DTCM memory regions.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The STM32L433 has the same layout than the STM32L432, additionally it
has GPIOD, GPIOE, I2C2, USART3 and SPI2.
Also move USART3 and SPI2 out of stm32l4.dtsi since STM32L432 does not
have it.
Fixes#10909.
Signed-off-by: Markus Roppelt <markus.roppelt@gmx.de>
The Silicon Labs EFM32 Pearl Gecko MCU includes:
* Cortex-M4F core at 40MHz
* up to 1024KB of flash and 256KB of RAM
* multiple low power peripherals
Ported from EFM32WG:
https://www.silabs.com/documents/public/application-notes/an0918.0-efm32_to_efm32jgpg_migration_guide.pdf
Signed-off-by: Gil Benkö <gil.benkoe@pm.me>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds the virtualcom device to the nrf52840 SoC dts and adds a board
specific nrf52840_overlay.dts file, copied exactly from the
arduino101_overlay.dts file, to set the console device name
appropriately for the subsys/usb/console sample project.
There were no clear alternatives to add a usb_cdc: virtualcom device to
all known SoC devices with USB support as should probably happen.
There was also no clear alternatives to add a non-board specific overlay
to the example.
This fixes a specific problem with the nrf52840-dk board for this sample
project.
Signed-off-by: Tom Burdick <thomas.burdick@gmail.com>
This commit adds support for STM32L471xG. Since STM32L475 only adds
USB, stm32l475.dtsi now includes stm32l471.dtsi
Signed-off-by: Kiril Zyapkov <k.zyapkov@allterco.com>
This patch adds a flash driver for the Atmel SAM E70 SoC. The driver has
been kept simple by considering that the flash is only composed of 8-KiB
blocks. Indeed an area at the beginning of the flash might be erased
with a smaller granularity, and the other blocks can also be erased with
a higher granularity. It also only handles the global read/write
protection, not the 128-KiB lock regions. A write error is returned if
a region is locked.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Enables Networking hardware on i.MX-RT type drivers.
Reuses the same eth_mcux driver used by Kinetis family; initialization
sequence refactored to work with this board as well. Unlike Kinetis
family, i.MX has a single ENET interrupt and we need to discriminate
between interrupts using a status register.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Add Messaging Unit B peripheral support for i.MX6SoloX soc so it can
use IMX IPM.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
dtc was producing this warning when we build on SAMD SoCs:
Warning (simple_bus_reg): /soc/nvmctrl@41004000:
simple-bus unit address format error, expected "40022000"
The reg addr isn't used by the flash_sam0.c driver so we wouldn't notice
this issue. Looking at the atmel HAL we see:
#define NVMCTRL ((Nvmctrl *)0x41004000UL)
So that provides confirmation of what the reg addr should be.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32F103 micros starting from 64-pin (xE) packages upward have
available port G. This patch defines a dts binding for them.
Signed-off-by: Pavel Kral <pavel.kral@omsquare.com>
Add #pwm-cells to the i.MX PWM binding and dts files. This is to
support have a pwms clients work properly.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add #pwm-cells to the STM32 PWM binding and dts files. This is to
support have a pwms clients work properly.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Newer DTC now warns about mismatch between the reg and unit-address.
Most of these cases are due to case not matching, so fix thoses so
everything is lowercase.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The information extracted from the device tree is now used to initialize
GPIO device instances. Up until now the GPIO device driver made no use
of this information. Actual instance creation is still controlled using
the Kconfig method. Missing GPIO device tree nodes were added in the
process for STM32L073, STM32F413 and STM32F373.
The information for gpio instance initialization has already been
present for supported STM32 SoCs but remained unused. Changes in the
device tree had no effect on GPIO functionality and was essentially
redundant. Using the device tree for hardware description seems
plausible and less painful than a myriad of defines in some SoC
description header.
The change was implemented under the assumption that current device
trees provide a correct description of the SoCs. Base register addresses
and RCC register bits were not explicitly checked for each device.
Manual tests were executed on:
- NUCLEO-F103RB
- STM32F429I-DISCO
- STM32F746G-DISCO
- NUCLEO-F767ZI
Manual tests consisted of blinky on different GPIOs and pins on each
board.
sanitycheck was executed for all STM32 based boards
Fixes: #10629
Signed-off-by: Martin Bertsche <martin72216@googlemail.com>
Update stm32f469i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
-Update yaml file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32l496g_disco configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update disco_l475_iot1 configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The only difference between the F413xH and F413xG is flash memory size.
STMF413xH: 1536 Kbytes
STMF413xG: 1024 Kbytes
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
This patch adds a USB device driver for the USBHS device that can be
found on Atmel SAM E70 SoC family. Only the FIFO mode is supported
(as opposed to DMA). It supports LS, FS and HS modes, but defaults to
FS mode as Zephyr does not fully support HS mode yet.
Tested examples on an Atmel SMART SAM E70 Xplained Board:
* usb/cdc_acm
* usb/hid-mouse
* usb/mass
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add clocks property in stm32l4r5 devices.
Replace i2c2 node by i2c3 node in l4.dtsi as i2c3 available
in all stm32l4 SoCs while i2c2 is not available in some parts.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add dts binding and info for TRNG device and enable basic support to
get the device name from DTS. We leave for now the base addresses
coming from the MCUX HAL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add dts binding and info for RNGA device and enable basic support to
get the device name from DTS. We leave for now the base addresses
coming from the MCUX HAL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add #pwm-cells properties to kinetis dts files and update the yaml
binding to spec the two cells as pin and period (in nanosecond to match
Linux Kernel binding spec).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert gpio_cc32xx driver over to using device tree. Added binding
files, updates to dts for various SoCs that use cc32xx.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adding watchdog driver for sam SoC. The current implemntation just
diables the watchdog on device boot.
This PR adds the following support for SAM3X, SAM4S and SAME70
1. Activate processor reset
2. Activate all reset
3. Generate interrupt on watchdog timer expiration.
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Silicon Labs EFR32MG12P Mighty Gecko MCU includes:
* Cortex-M4F core at 40MHz
* up to 1024KB of flash and 256KB of RAM
* integrated Sub-GHz and/or 2.4GHz radio
* multiple low power peripherals
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Signed-off-by: Endre Karlson <endre.karslon@gmail.com>
Partially replaces Kinetis MCUX driver configuration from Kconfig to
Device Tree. Interrputs moved from defines configuration to DT.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Introduces the location property and adds the ability to use values
generated by the device tree configuration.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add I2S bus initial support to stm32f4 SOC family.
On stm32f4 the I2S shares same controller as SPI, so
the declarations have been adapted from SPI ones.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The Silicon Labs EFM32 Happy Gecko MCU includes:
* Cortex-M0+ core at 24MHz
* Up to 64KB of flash and 8KB of RAM
* Full speed (12 MHz) USB 2.0 Device
* Multiple low power peripherals
Signed-off-by: Marcio Montenegro <mtuxpe@gmail.com>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Convert gpio_gecko driver over to using device tree. Added binding
files, updates to dts for various SoCs that use gpio_gecko.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add maximum-speed property to usb nodes and set it to
their maximum on-chip PHY capability.
SoCs with USB device controllers only support full
speed, so we don't add maximum-speed to these nodes.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The gpio controllers on SAM4S, SAME70, and SAMD were missing properties
related to GPIO pin generation. Add the missing details into the yaml
and dts files to allow boards to specific gpio pins.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
added sam4s16b, sam4s8c, sam4s8b, sam4s4c, sam4s4b,
sam4s4a, sam4s2c, sam4s2b and sam4s2a.
Used the same order as in the data sheet and code structure
equal to same70. Updated the sam4s_xplained board to match
the altered .dtsi location of the specific SoC.
Signed-off-by: Vincent van der Locht <vincent@vlotech.nl>
This patch adds timers and PWM nodes to STM32 F7 series, as well as the
corresponding dts fixup entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that we've cleaned up all the STM32 related .dtsi files we don't
use dts/arm/st/mem.h so we can remove it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F7 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F3 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F2 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the L4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the L0 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F1 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F0 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added initial support and created the corresponding device tree part for
building PSoC6 SoC as part of Zephyr.
Signed-off-by: Nazar Chornenkyy <nazar.chornenkyy@cypress.com>
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
Commit introduces support for ARM TrustZone CryptoCell 310
for Nordic Semiconductor nRF SoCs in device tree.
Signed-off-by: Dominik Kilian <Dominik.Kilian@nordicsemi.no>
Flash controller-node for stm32f2 based SoCs was missing basic
properties such as compatible, labeln reg and interrupts.
Fix this and add matching yaml binding file;
Fixes#10057
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When we fixed the missing reg property in the cpu node, we forgot to
add #address-cells & #size-cells for the node.
This fix the following warnings we get:
Warning (reg_format): "reg" property in /cpus/cpu@0 has invalid
length (4 bytes) (#address-cells == 2, #size-cells == 1)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This change aims at fixing 'unit_address_vs_reg' warning in
stm32 *-pinctrl.dtsi files.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for led nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@xx' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /flash: node has a reg or ranges
property, but no unit name
or
Warning (unit_address_vs_reg): /memory: node has a reg or ranges
property, but no unit name
Fix by adding unit address that is missing to flash & memory nodes.
Additionally the Silabs memory nodes didn't have a compatiable or
device_type, so add those properties as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /cpus/cpu@0: node has a
unit name, but no reg property
Fix by adding reg property to missing cpu nodes.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_NRF51822_QFAA
CONFIG_SOC_NRF51822_QFAB
CONFIG_SOC_NRF51822_QFAC
CONFIG_SOC_NRF52810_QFAA
CONFIG_SOC_NRF52832_QFAA
CONFIG_SOC_NRF52832_CIAA
CONFIG_SOC_NRF52832_QFAB
CONFIG_SOC_NRF52840_QIAA
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_PART_NUMBER_SAME70*
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have a common DT_SIZE_K macro use it instead of defining
__SIZE_K eveywhere. We also have DT_SIZE_M, so use that in a few
places as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The RTC node for some reason was setting #address-cells and #size-cells.
However it has no children so there isn't really any reason to do this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In case of out of tree SoC, mem.h will trigger and error since
it is not aware of new SoC CONFIG_SOC_<reference>.
Modify error condition in order to generate the error only if
the flash and error size are not defined at this point (even in
out of tree case).
Fixes#9978
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_PART_NUMBER_EFM32WG990F256
CONFIG_SOC_PART_NUMBER_EFR32FG1P133F256GM48
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_CC3220SF
CONFIG_SOC_MSP432P401R
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The LEDs, buttons and necessary aliases are now configured via dts.
This commit breaks the sample under samples/boards/nrf52/power_mgr.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
According to Device Tree specification, previously
defined nodes may be deleted with the followin
syntax:
/delete-node/ node-name;
or
/delete-node/ &label;
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This change adds DTS definition of SPI device for nRF chips.
It also removes SPI pin configuration from Kconfig and moves it to
chip DTS.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
This commit adds ADC nodes to DTS files for nRF SoCs and introduces
corresponding bindings for these nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The whole STM32L4 family has a flash with a constant page size of 2kB.
Specify this value in the DTS as the nvs sample application pull it
from there.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The nvs sample assumed a 1 KB flash erase block size, which caused the
sample to fail on frdm_k64f because its erase block size is 4 KB. Get
the erase block size from dts instead.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add support for usbotg_fs, by adding the DT fixup, pinmux macros,
and the DT entries in stm32f2.dtsi.
Signed-off-by: Istvan Bisz <istvan.bisz@t-online.hu>
The L433 chip is a superset of the L432, just grabbing a few additional
interfaces (LCD, I2C2, USART3, SPI2, SDMMC). All the support/HAL files
are already there, so enabling these is just a matter of build system
setup.
Tested on an application specific board (builds correctly and I2C2
works.) I unfortunately don't have a nucleo/discovery board to create a
reference board for.
Signed-off-by: David Lamparter <equinox@diac24.net>
This patch adds the RDC (Resource Domain Controller) peripheral
permissions settings for the i.MX applications cores (Cortex A9 on
i.MX6 and Cortex A7 on i.MX7).
This will enable both Linux (on application's core) and Zephyr (on M4
core) to share the peripherals and coexist.
The settings are defined at devicetree level and applied in the soc.c.
A complete solution should involve the SEMA4 to control the peripherals
access and prevent resource deadlocking and misusage.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
The STM32F7 uses the V2 version of the STM32 I2C controller. Add the
corresponding Kconfig, DTS, DTS fixup and pinmux entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This commit adds support for the nrf52840_pca10059 board.
The flash partitions are configured to allow migrating from
the stock bootloader to MCUBoot.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The STM32F7 uses the same USB OTG FS controller than the STM32F4 series.
It is therefore trivial to add support for it, by adding the DT fixup
and pinmux macros, and the DT entries in stm32f7.dtsi. Keep it disabled,
it should be enabled at the board level.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
samd21.dtsi includes now the same content need for SAMD20,
move it to samd.dtsi and include it from samd21.dtsi.
Then later USB support can be added to the samd21.dtsi seperatly
from the samd20 etc.
Signed-off-by: Sean Nyekjaer <sean@nyekjaer.dk>
The EFR32 Flex Gecko Wireless Starter Kit contains sensors and
peripherals demonstarting the usage of the EFR32FG1P SoC
family. This patch add basic support for this board.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Since the UART0 @ 0x40002000 can either be UART or UARTE the user of the
soc.dtsi needs to select either compatible = "nordic,nrf-uarte" or
"nordic,nrf-uart"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The STM32F769 has more interrupts and features than the STM32F746,
but the basic support is similar with STM32F746
Signed-off-by: Yong Jin <jinyong.iot@foxmail.com>
clear RXNE flag in fifo_read, remove TEACK and REACK
check when uart_stm32_init because stm32f2 doesn't
has those flags.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
The STM32F723 has more interrupts than the STM32F746 due to the
additional SDMMC controller. Besides that the changes are very
similar to the ones of the STM32F746.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch includes:
STM32F7 family device tree file with basic and UART definitions.
STM32F746 subfamily device tree file.
Memory definitions for STM32F746xG subfamily.
Signed-off-by: Yurii Hamann <yurii@hamann.site>
STM32F412/413/446/469 SoCs have 6 bidirectional endpoints
according to the reference manuals RM0402, RM0430,
RM0390 and RM0386.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This commit moves the definitions for the LED and Buttons
supported in nrf52810_pca10040 DK in DTS from board.h. Aliases
are kept in board.h to make basic examples pass.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The nRF52810 is a low-cost variant of the nRF52832, with a reduced set
of peripherals and memory. This commit adds basic support for it in the
arch SoC and dts folders.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Ioannis Glaropoulos <ioannis.glaropoulos@nordicsemi.no>
The i.MX 6SoloX SoC is a hybrid multi-core processor composed by one
Cortex A9 core and one Cortex M4 core.
Zephyr was ported to run on the M4 core. In a later release, it will
also communicate with the A9 core (running Linux) via RPMsg.
The low level drivers come from NXP FreeRTOS BSP and are located at
ext/hal/nxp/imx. More details can be found at ext/hal/nxp/imx/README
The A9 core is responsible to load the M4 binary application into the
RAM, put the M4 in reset, set the M4 Program Counter and Stack Pointer,
and get the M4 out of reset.
The A9 can perform these steps at bootloader level after the Linux
system has booted.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
The various STM32 reference manuals sometimes define the USB endpoints
as IN or OUT only and sometimes as bidirectional, even in the same
manual. This is likely because the OTG implementation has one set of
registers for the IN endpoints and one other set for OUT endpoints.
However at the end a given endpoint address can both transmit and
receive data.
This causes some confusion how to declare the endpoints in the device
tree, and depending on the SoC, they are either the same number of IN
and OUT endpoints declared, or they are declared as bidirectional. At
the end it doesn't really matter given how the driver uses those values:
#define NUM_IN_EP (CONFIG_USB_NUM_BIDIR_ENDPOINTS + \
CONFIG_USB_NUM_IN_ENDPOINTS)
#define NUM_OUT_EP (CONFIG_USB_NUM_BIDIR_ENDPOINTS + \
CONFIG_USB_NUM_OUT_ENDPOINTS)
#define NUM_BIDIR_EP NUM_OUT_EP
This patch therefore cleanup the driver, the DTS, and the DTS fixups to
only define the number of bidirectional endpoints.
In addition to the cleanup, that fixes a regression introduced by commit
52eacf16a2 ("driver: usb: add check for endpoint capabilities"), which
introduced a wrong check for SoC only defining the number of
bidirectional endpoints.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This commit enables CAN on the STM32L432.
Tested on nucleo l432ck with external transceiver and loopback mode.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit splits the common interrupt into rx and tx parts because
only STM32F0 series has a common interrupt.
Moved clock source definition to device-tree.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
The prepended 0x causes DTC warnings and shouldn't be there.
Tested by compiling hello_world for nrf52840_pca10056 before and after.
Fixes#8334.
Signed-off-by: Alex Tereschenko <alext.mkrs@gmail.com>
This adds basic support for declaring gpio nodes in dts for nrf52.
The dts.fixup provides mapping for the generated defines to the config
defines currently used by the nrf gpio driver.
Existing boards that use nrf52 are updated.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
This commit moves the bit timing (PROP, BS1, BS2 segments and SWJ)
from Kconfig to the device-tree and fixes issue #7933
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Enable supporting UART4 on STM32F107 and STM32F103Xe SoCs.
Modified stm32f1/dts.fixup for replacing USART with UART.
Signed-off-by: Jun Li <jun.r.li@intel.com>
LPUART (Low-power UART) peripheral is just like ordinary U(S)ART
which lives in a separate clock/power domain.
Therefore already existing code could be reused as is
almost entirely.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
The STM32L432 SoC has a standard non-OTG USB controller. Add an entry
for it in stm32l432.dtsi and add the corresponding DTS fixup entries.
The controller is kept disabled and should be enabled at the board
level.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
USB OTG is currently enable for the whole STM32L4 family, while only a
few of them actually support it:
- STM32L475, STM32L476 and STM32L496 have an OTG controller
- STM32L432, STM32L433 and STM32L452 have an USB controller
- STM32L431, STM32L451 and STM32L471 do not have any USB controller
Fix that by moving the DT entry from stm32l4.dtsi to stm32l475.dtsi
and by adding a #ifdef #endif around the corresponding DTS fixup
entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add driver for MCUX mailbox which can be used for lpcxpresso54114
and other lpc and kinetis socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Add soc configuration support and dts files for nxp_lpc54xxx_m0.
Adjusted nxp_lpc54xxx soc, configuration and dts files for the
presence of slave core.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds dts bindings for the kinetis watchdog peripheral, and updates the
watchdog nodes for the k64 and kw2xd socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds some DTS information to flesh out the NXP Kinetis
based RTC blocks. DTS fixups were added as well to match up the driver
usage to the DTS output.
Signed-off-by: Andy Gross <agross@kernel.org>
Rename various SoC related defines and files from just being LPC54114
to LPC54114_M4. This is in prep for supporting a build for the second
core on the LPC54114 (the Cortex-M0+).
* Renamed Kconfig SOC_LPC54114 to SOC_LPC54114_M4
* Renamed Kconfig.defconfig.lpc54114 to Kconfig.defconfig.lpc54114_m4
* Introduced nxp_lpc54xxx_m4.dtsi based on nxp_lpc54xxx.dtsi
* Moved some pinmux related defines into SoC code.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Changed define for SETTINGS_CONFIG_PAGE_SIZE from a hard coded value
to reference build system generated FLASH_ERASE_BLOCK_SIZE. This value
comes from 'erase-block-size' found in the dtsi file of devices.
- Modified nrf52840.dtsi to include definition for 'erase-block-size'
Fixes#7107
Signed-off-by: David Leach <david.leach@nxp.com>
Commit introduces support for watchdog configuration for Nordic
Semiconductor nRF SoCs in device tree.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Adds dts bindings for the mcr20a wireless transceiver. The frdm_k64f
board supports the mcr20a via an Arduino shield, therefore the dts node
is added to the board dts. The kw2xd is a SiP and thus the mcr20a dts
node is added to the soc dts.
The networking samples using prj_frdm_k64f_mcr20a.conf have been broken
since the refactoring of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts spi bindings for the kinetis dspi controller, and updates the
k64, kw2xd, kw40z, kw41z dts nodes accordingly.
Updates the dts interrupt priorities to match the board defconfigs
(e.g., boards/arm/frdm_k64f/Kconfig.defconfig)
For k64, fixes an error in the spi1 interrupt number and adds a third
instance (spi2).
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds flexspi and semc memory controllers to the i.MX RT SoC. Adds
hyperflash, qspi, and sdram external memories to the mimxrt1050_evk
board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Previously, when !CONFI_XIP, BOOTLOADER_SRAM_SIZE was defaulted
to 16 (K), reducing the size of SRAM available for the program.
Also, though it has no effect, the value for SRAM start in the
dtsi file was incorrect.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
To prepare to upcoming dtc v1.4.6, fix warnings in dts files.
This commit addresses the following warning:
Warning (unit_address_vs_reg): Node /soc/pin-controller has a reg
or ranges property, but no unit name
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To prepare to upcoming dtc v1.4.6, fix warnings in dts files.
This commit addresses the following warning:
Warning (clocks_property): Missing property '#clock-cells' in node
/soc/rcc@40021000 or bad phandle (referred from
/soc/pin-controller/gpio@40011800:clocks[0])
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adds gpio labels to all kinetis socs in preparation for refactoring the
mcux gpio driver to dts. The kl25z was missing gpio nodes altogether, so
they are added.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Create a dt-bindings/gpio.h file.
Bindings definitions are extracted from existing gpio.h.
gpio dt-bindings file is required because existing gpio.h file could
not be parsed by dts parser.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The i.MX7 SoC is a Hybrid multi-core processor composed by Single/Dual
Cortex A7 core and Single Cortex M4 core.
Zephyr was ported to run on the M4 core. In a later release, it will
also communicate with the A7 core (running Linux) via RPmsg.
The low level drivers come from NXP FreeRTOS BSP and are located at
ext/hal/nxp/imx. More details can be found at ext/hal/nxp/imx/README
The A7 core is responsible to load the M4 binary application into the
RAM, put the M4 in reset, set the M4 Program Counter and Stack Pointer,
and get the M4 out of reset.
The A7 can perform these steps at bootloader level after the Linux
system has booted.
The M4 can use up to 5 different RAMs. These are the memory mapping for
A7 and M4:
+---------------+-----------------+---------------------------+
| Memory Name | Start Address | Size |
+===============+=================+===========================+
| TCML | 0x007F8000 | 32KB |
+---------------+-----------------+---------------------------+
| TCMU | 0x20000000 | 32KB |
+---------------+-----------------+---------------------------+
| OCRAM_S | 0x20180000 | 32KB |
+---------------+-----------------+---------------------------+
| OCRAM | 0x00900000 | 128KB |
+---------------+-----------------+---------------------------+
| DDR | 0x10000000 | 256MB |
+---------------+-----------------+---------------------------+
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
With upcoming ICs that are not in the nRF5x family, rename the flash
driver and all its dependencies from nrf5 to nrf.
Should also fix the issue introduced by f49150cab6 which broke the
assignment of the flash device due to a partial rename.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add initial support for STM32L073xZ SOC which is not very different
from already supported STM32L072xZ.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Since not all boards enable all devices, we typically have the SoC dtsi
file have a device marked with status = "disabled" and have the
board.dts explicitly enable with status = "ok". Update it so USB on
Atmel SAMD21 work this way.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch the SoC device tree to define a single entry per SERCOM instead
of one per mode.
Define a Device Tree binding for the SAM0 SPI and use it instead of
Kconfig for enabling / disabaling instances
Switch the Arduino Zero, Adafruit Feather M0 Basic Proto, and
Trinket M0 to use the new defintion.
Add the APA102 LED that's on the Trinket as a test.
Signed-off-by: Michael Hope <mlhx@google.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implements interrupt driven UART for the serial driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Justin Watson <jwatson5@gmail.com>
The spi nodes should have #address-cells and #size-cells properties much
like i2c does. Add these missing properties.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Most STM32F429 SoCs have 6 SPIs, but STM32F429Vx SoCs only have
4 SPIs. This is one of the rare conditions where device-tree
directive /delete-node/ should be used.
Add spi5 and spi6 node to stm32f429.dtsi. Create file
stm32f429vX.dtsi to delete those nodes and document usage of
/delete-node/ directive.
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Some stm32f4 SoCs don't support spi2, so remove spi2
device-tree node from stm32f4.dtsi file.
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
stm32f405 is not an expansion of stm32f411, since stm32f411 has more
SPIs than stm32f405.
Fix this by including stm32f401.dtsi in stm32f405.dtsi
(instead of stm32f411.dtsi).
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Configure ccm size and address via dts. According to the DT
specification, the unit-address of a node must match the
first address specified in the reg property of the node.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
stm32f334 is not an expansion of stm32f303, since
stm32f303 has more I2C, SPI ports than stm32f303.
Fix this by including stm32f3.dtsi in stm32f334.dtsi.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This PR includes the required changes in order to support
conditional compilation for Armv8-M architecture. Two
variants of the Armv8-M architecture are defined:
- the Armv8-M Baseline (backwards compatible with ARMv6-M),
- the Armv8-M Mainline (backwards compatible with ARMv7-M).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Pin multiplexing is a function of the PORT peripheral. This change
defines a separate pinmux device at the same address as the PORTs
themselves.
Signed-off-by: Michael Hope <mlhx@google.com>
Adds a new optional dts property to define the erase block size of a
flash device. This will be used by the mcux flash driver to implement
the flash page layout function.
The value is set for all kinetis devices to match
FSL_FEATURE_FLASH_PFLASH_BLOCK_SECTOR_SIZE.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add device tree support for the "nxp,kinetis-ftfa" flash controller used
on the NXP KL2X and KW4xZ SoCs.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert NXP k6x and kw2xd flash driver to use device tree to get the
flash controller name from device tree. We introduce yaml bindings for
the "nxp,kinetis-ftfe" and "nxp,kinetis-ftfl" devices.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On the various NXP Kinetis SoCs add the write-block-size property and
set it to match FSL_FEATURE_FLASH_PFLASH_BLOCK_WRITE_UNIT_SIZE for the
given SoC.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert Atmel SAM0 flash driver to use device tree to get the flash
controller name and base address.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce flash controller nodes for STM32 SoCs that are supported in
the flash driver. This is a precusor to converting the flash driver on
stm32 over to using device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Where missing add compatible = "soc-nv-flash". Also added a label for
all the soc-nv-flash that we might use in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commits adds the "least common denominator" in the
stm32fX.dtsi files and fills the additional SPI nodes
in stm32fXYZ.dtsi files, only for the SOCs where boards
use the additional SPI peripheral.
We could add the rest SPI nodes in the stm32fXYZ.dtsi
files when we add SPI support to other boards.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The SAM0 has a 64 byte page (the programing unit) with 4 pages to a
row (the erase unit). This driver implements a read/modify/write to
emulate the byte level writes used by NFFS.
Signed-off-by: Michael Hope <mlhx@google.com>
This was validated on the cc3220sf_launchxl board
using the Zephyr thermometer sample program
adapted to call the i2c driver directly, and fetching
samples from the on-board TMP006 temperature sensor.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Add configuration, pinmux, dts and documentation for the STM32L476G
Discovery board based on the STM32L476VG SoC.
Signed-off-by: Arthur SFEZ <arthur.sfez@gmail.com>
Adds the mimxrt1052 SoC, which belongs to a new family (nxp_imx) and
series (rt) of SoCs. The mimxrt1052 integrates an Arm Cortex-M7 core,
512 KB TCM, and many peripherals including 2D graphics, an LCD display
controller, camera interface, SPDIF and I2S. Unlike other SoCs in
Zephyr, the mimxrt1052 has no internal flash.
This initial port to mimxrt1052 configures the system clock to operate
at 528 MHz, and enables the serial/uart and gpio interfaces to support
the hello_world and blinky samples. Support for additional Zephyr driver
interfaces will come later.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the dts fixup files into the board dir so that board ports can be
more standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If DTS does not depend on include paths determined in /ext then we can
move dts next to kconfig. Moving it next to kconfig means that DTS
CONFIG_ variables will be available at the same time as kconfig's
CONFIG_ variables which is the intended design and beneficial from a
usability perspective.
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Boot serial recovery feature consume additional
memory size so the mcuboot partition must been
expanded on cost of images partitions.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Boot serial recovery feature consume additional
memory size so the mcuboot partition must been
expanded on cost of images partitions.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add board configuration, dts and pinmux, based on
arm/stm32f4_disco and arm/nucleo_f411re boards.
Error free tests are executed on eval board with the following
sample applications:
- hello_world
- blinky-sample
- button-sample
- console_echo_sample
- console_getchar_sample
Signed-off-by: Jose F. Fernandez <jffernandez@fenix-es.com>
Moved yaml files to be under dts/bindings and have the bindings try
and match the linux doc device tree binding dir structure as the
canonical binding reference.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Adds device tree bindings for the Kinetis System Integration Module
(SIM), and defines peripheral source clocks (e.g., system clock or bus
clock) and clock gates for all Kinetis SoCs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds support for TI Simplelink MSP-EXP432P401R-LAUNCHXL
development board based on Cortex M4 family
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds support for on board UART_0 on MSP-EXP432P401R-LAUNCHXL.
Driver makes use of driverlib available in ROM by default, thus saving
code space.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The EFM32 Wonder Gecko Starter Kit contains sensors and
peripherals demonstarting the usage of the EFM32WG MCU
family. This patch add basic support for this board.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Silicon Labs EFM32 Wonder Gecko MCU includes:
* Cortex-M4F core at 48MHz
* up to 256KB of flash and 32KB of RAM
* USB with host and OTG support
* multiple low power peripherals
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
stm32f407 SoC is an extension of stm32f405 SoC with additional
support of ethernet and DCMI. Hence, in dts description, this
should be represented by stm32f407.dtsi including stm32f405.dtsi.
The opposite was proposed today in stm32 .dtsi files.
This commit fixes the inclusion model and renames
stm32f407-pinctrl.dtsi into stm32f405-pinctrl.dtsi
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This makes the SoC flash compatible with the common nonvolatile flash
YAML schema, and provides a write alignment. It mirrors work done on
nRF chips for the DFU subsystem.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This makes the SoC flash compatible with the common nonvolatile flash
YAML schema, and provides a write alignment. It mirrors work done on
nRF chips for the DFU subsystem.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This makes the SoC flash compatible with the common nonvolatile flash
YAML schema, and provides a write alignment. It mirrors work done on
nRF chips for the DFU subsystem.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This patch adds partition for NFFS for nRF51, nRF52 and nRF52840.
The partition is placed at the end of flash. This is only added if NFFS
is enabled (since it's required) - in other case free space can be used
for other purposes.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Similar addition was don previous for nRF52840.
Added flash-controller description and moved flash description to
it. Added property for description of
the flash alignment required by write operations.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Similar addition was don previous for nRF52840.
Added flash-controller description and moved flash description to
it. Added property for description of
the flash alignment required by write operations.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Remove usart2_pins_b as this configuration is not possible
(PA15 could not be mapped on USART2).
Besides usart2_pins_c as this configuration is not used yet,
remove to reserve "usart2_pins_c" for future use
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Default configuration for USART1 (Console output) on board
stm32f3_disco was set on PA9/PA10, which matches Rev-A/B
configuration. Though, on more recent configuration of the
board (Rev-C onward). USART1 is mapped to PC4/PC5.
This configuration has the benefit to support VCP, hence it
is chosen to be set by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add board configuration, dts and pinmux based on both
stm32f469i_disco board and nucleo_f412zg board
Signed-off-by: Massimiliano Cialdi <massimiliano.cialdi@powersoft.it>
Fixes uart irq info in the device tree fixup files for frdm_k64f and
hexiwear_k64. They were incorrect in uart instance 5.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch enables I2C_2 support for 96b_carbon. Without
this patch, trying to build I2C_2 will result in build
error.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Added flash-controller description and moved flash description to
it (for coherence). Added property for description of
the flash alignment required by write operations.
Thanks to that l-value FLASH_WRITE_BLOCK_SIZE macro
will be generated. It is useful for any component uses
the flash.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
We use UART1 for UART pipe in a number of qemu tests, so lets do the
same thing for the bluetooth test and move the bluetooth uart to UART2.
Jira: ZEP-2412.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Per ZEP-1958, Phase 2 of adding CC3220sf LaunchXL support,
was to "deprecate the CC3200 launchxl support in Zephyr
(redundant to the CC3220)."
Effectively, the CC3220 SOC replaces the CC3200.
This patch removes the following:
* the imported CC3200 SDK
* CC3200 SOC, board, DTS files.
* adjusts other files where cc3200 was mentioned.
Also, it fixes explicit references to CC3200 in generic
CC32xx driver files.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
pin-controller reg is already set in stm32f407.dtsi which we include in
stm32f469.dtsi so no need to set it again.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds common and Kinetis-specific pwm device tree properties, and updates
the k64 SoC and board dts files to include all four pwm nodes.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
- board name olimex_stm32_p405
- CPU STM32F405RGT6 Cortex M4
- LED/BUTTON support
- Console on USART2 with 8n1 115200 baud
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move to using the generated IRQ defines from the DTS instead of soc.h.
This change also fixes a minor bug in that the error irq priority wasn't
getting correctly picked up from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add needed uart pinctrl configuration in pinmux node.
Populate stm32 f1 based boards dts files with references
to uart pinctrl nodes
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add needed uart pinctrl configuration in pinmux node.
This is done thanks to <soc>-pinctrl.dtsi file matching
<soc>.dtsi files
Populate stm32 f3 based boards dts files with references
to uart pinctrl nodes
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add needed uart pinctrl configuration in pinmux node.
This is done thanks to <soc>-pinctrl.dtsi file matching
the <soc>.dtsi files
Populate stm32 f4 based boards dts files with references
to uart pinctrl nodes.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add pinctrl node on stm32l4 soc dts files, including uart
pinctrl configurations. This is done thanks to <soc>-pinctrl.dtsi
file matching the <soc>.dtsi file
Populate stm32 l4 based boards dts files with references
to uart pinctrl nodes
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add pinmux yaml file and bindings before introduction
of pinmux node in stm32 soc device tree files
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When we introduced I2C DTS support on hexiwear_kw40z we got it wrong.
Its I2C1 not I2C0 that was being used on the hexiwear. Fix the dts and
fixup file to reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update the I2C defines in fixup files after the introduction
of cell prefix to interrupts-names generated defines
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Now that we generate BLUETOOTH_UART_ON_DEV_NAME, UART_PIPE_ON_DEV_NAME,
and BLUETOOTH_MONITOR_ON_DEV_NAME Kconfig defines for dts enabled
platforms add those into the appropriate dts files and remove from the
various board/Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In order to simplify maintenance of dts files for
stm32f4 series, introduce a stm32l4.dtsi file which
represent the smallest common denominator of IPs in
the family.
This allows to fix usart4 availability on stm32l432
which was not correct.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to simplify maintenance of dts files for
stm32f1 series, introduce a stm32f3.dtsi file which
represent the smallest common denominator of IPs in
the family.
Besides, stm32f334 includes stm32f303, as it is a
extension of this SoC.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to simplify maintenance of dts files for
stm32f1 series, introduce a stm32f1.dtsi file which
represent the smallest common denominator of IPs in
the family.
Besides, stm32f103Xe includes stm32f103xb, as it is a
extension of this SoC.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add "clocks" property on u(s)arts nodes on stm32 socs
Add a dt clocks binding file and rework clock_control
header file include new device tree binding file.
include/dt-bindings folder is introduced as dt-bindings
placeholder
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Remove memory node from skeleton dtsi and add device_type
property in every memory node in soc dtsi files
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This patch add the unit-address component to memory and flash
nodes. According to the DT specification, the unit-address of
a node must match the first address specified in the reg
property of the node.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Remove all explicitly defined application state partition child nodes
from DTS flash nodes, in favor of comments noting that they are
reserved for use by the application.
This follows the pattern established in f58b36a ("dts: frdm_k64f: make
application state partition a reserved area"), and fixes an error
introduced in 9f7f83d2 ("dts: 96b_nitrogen: add flash partitions"),
which added both a reserved area comment and an explicit partition
node to 96b_nitrogen's dts.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Remove compatible = "flash" from any node that has it as this doesn't
have any well defined meaning right now. Also update any compatible =
"sram" to be "mmio-sram" (as there's a binding in linux for this).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update the MCUX I2C driver and related platforms to get their I2C
information from the device tree. We also updated a few of the sensor
drivers found on the FRDM & Hexiwear boards to get their I2C bus name
from the device tree instead of directly from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds #address-cell, #size-cell properties to
cpus container node and device_type, reg properties to
cpu node.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Adds common and Kinetis-specific adc device tree properties, and updates
all Kinetis SoC and board dts files to include adc nodes.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
patch adds zephyr,uart-pipe to devie tree as chosen property.
This is added for frdmk64f because sanitycheck test was
breaking with changes of generating configs for UART_PIPE
from device tree instead of Kconfig.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>