We shall not enable by default a system timer in ARM
platforms, namely the SysTick, the Nordic, or the SAM0
RTC timer, simply by assessing the hardware capabilities
(e.g. by conditioning on CPU_CORTEX_M_HAS_SYSTICK).
Instead, now, all ARM platforms needs to explicitly set
their system timer module. Note that this has already
been the case for ca 80% of the ARM platforms.
This clean-up allows us to decouple HW capabilities from
system configuration (for example, Nordic platforms may
enable option CPU_CORTEX_M_HAS_SYSTICK, and still use
the platform-specific RTC timer for system timing).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Reduced flash size for QEMU x86 so it does not consume a lot of RAM
memory where it is simulated.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
This commit adds a flash driver implementation that writes to RAM and
exports statistics through stats.h. It can be used to simulate flash
memory for testing purposes.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Add board support for 96Boards WisTrio LoRa Tracker board from
RAK Wireless. This board is one of the 96Boards IoT Edition platform.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
We already select HAS_DTS at the arch level for X86 so we don't need to
duplicate it at the board level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add configuration, pinmux, dts and documentation for the STM32MP157
Discovery board based on the STM32MP157 SoC.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Mark the three distinct choices for how to program the board as
separate options, and add some clarifications on each. For the MCUboot
route, use smp_svr instead of blinky, to give the user a hint about
how to keep their devices up to date from application land.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
This patch adds support to the nRF9160 for using a dedicated
GPIO pin to reset controllers running on nrf52840_pca10090.
It resets the controller before opening the H4 device, and it
delays the controller from booting until all bytes traveling
to the host have been received and drained from the UART,
thus ensuring that communication can begin from a clean state.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order to generalize the currently specialized nRF51 IC setup hook,
make the following changes:
- Generalize the hook to bt_ic_setup()
- Use a weak NOP version by default
- Move the currently existing one to the board folder
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Let one of the MCU interface pins be configured to act
as a reset line. This mitigates the lack of a connection
between the nRF9160 and nRF52840 PINRESET.
Minor refactoring and updated comments.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Add board support files for mimxrt1015_evk, the development board for
i.mxrt1015 (CM7) SoC.
- Add pinmux, dts, and doc.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
added three missing LEDS for stm32f4_disco, in order to run the
samples/basic/disco application on the stm32f4_disco
Signed-off-by: Jan Sturm <jansturm92@googlemail.com>
Be a bit more friendly to users, by providing some hints
about possible reasons why a command line option was not
understood.
Also describe in the help message that which options are
avaliable depends on what has been selected in this build.
Fixes: #15046
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Enables the pyocd runner on mimxrt1060_evk and mimxrt1064_evk boards
using the generic cortex_m target. Note that this target is not capable
of programming flash, therefore can only load an application to internal
SRAM (set CONFIG_CODE_ITCM=y and CONFIG_DATA_DTCM=y) or attach to an
application already programmed to flash by other means (e.g., DAPLink
drag-and-drop).
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Same deal as in commit 4638652214 ("Kconfig: Use 'default' instead of
'def_bool' in Kconfig.defconfig files"), fixing new stuff that got
introduced since then.
Some symbols, like ALTERA_AVALON_PIO, are only defined in
Kconfig.defconfig files, and so need the def_bool.
Motivation (from the note at the end of
guides/kconfig/index.html#common-shorthands):
For a symbol defined in multiple locations (e.g., in a Kconfig.defconfig
file in Zephyr), it is best to only give the symbol type for the "base"
definition of the symbol, and to use 'default' (instead of 'def_<type>'
value) for the remaining definitions. That way, if the base definition
of the symbol is removed, the symbol ends up without a type, which
generates a warning that points to the other definitions. That makes the
extra definitions easier to discover and remove.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add configuration, dts and documentation for the MINI-M4 for
STM32 board based on the STM32F415RG SoC.
See https://www.mikroe.com/mini-stm32f4 for more details.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
This commit adds CAN support for nucleo F746zg.
Furtermore CAN was added in stm32f7.dtsi and pinmuc_stm32f7.h
CAN_RX: PD0, CAN_TX: PD1
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
2 identical packages were defined for stm32f412 SoC, invariant "g".
Merge them in new sinclge stm32f412Xg.dtsi.
Update matching boards accordinlgy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
A parallel PCI implementation ("pcie") is added with features for PCIe.
In particular, message-signaled interrupts (MSI) are supported, which
are essential to the use of any non-trivial PCIe device.
The NS16550 UART driver is modified to use pcie.
pcie is a complete replacement for the old PCI support ("pci"). It is
smaller, by an order of magnitude, and cleaner. Both pci and pcie can
(and do) coexist in the same builds, but the intent is to rework any
existing drivers that depend on pci and ultimately remove pci entirely.
This patch is large, but things in mirror are smaller than they appear.
Most of the modified files are configuration-related, and are changed
only slightly to accommodate the modified UART driver.
Deficiencies:
64-bit support is minimal. The code works fine with 64-bit capable
devices, but will not cooperate with MMIO regions (or MSI targets) that
have high bits set. This is not needed on any current boards, and is
unlikely to be needed in the future. Only superficial changes would
be required if we change our minds.
The method specifying PCI endpoints in devicetree is somewhat kludgey.
The "right" way would be to hang PCI devices off a topological tree;
while this would be more aesthetically pleasing, I don't think it's
worth the effort, given our non-standard use of devicetree.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Right now only numerical values are printed which must
be looked up in the Designware ARCv2 ISA Programmer's
Reference, which is not public.
Add a non-default Kconfig to print more information at
the expense of footprint, and enable it for all the simulator
targets.
We only print code/parameter details for machine check and
protection violations, more may be added later as desired.
This should cover all the exceptions we commonly encounter
for memory protection.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
SPI is not normally enabled, but some tests assume that there's a device
available. Conditionally enable SPI_2 which is associated with the
on-board flash.
Closes#15374
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Remove 'counter' as a supported feature on several NRF boards as these
boards fail to build tests/drivers/counter/counter_basic_api. This is
due to the fact that we either need explicit board conf files for the
test or have the counter driver enabled via Kconfig.
Fixes#15460
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
for SDK 0.10.0, it consumes more stack size when coverage
enabled, so adjust stack size to fix stack overflow issue.
Fixes: #15206.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Fixes broken CC2520 on quark_se_c1000_devboard configuration after
commit 25d17db.
Fixes#15070
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This is a follow up to commit 436c4262da.
By default the channel 0 of pwm0 is set to the pin that drives led0.
Since the LED is active high, the inversion of polarity is incorrect.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
write_buf and flash_content should be defined as global inside
main. Otherwise Python treats them as local variables and ends
up throwing an error because it thinks they are being used
without being defined.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
for SDK 0.10.0, it consumes more stack size when coverage enabled
on qemu_x86 and mps2_an385 platform, adjust stack size for most of
the test cases, otherwise there will be stack overflow.
Fixes: #14500.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
For some reason we dropped the simulation keyword and this platform is
not running any tests, we are just building the tests.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename reserved function names in arch/ subdirectory. The Python
script gen_priv_stacks.py was updated to follow the 'z_' prefix
naming.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
* the nsim host timer does not work as expected,
disable it, use cycle count to simulate timer tick
* optmize the freq definition of nsim_em
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
On Clear Linux, the CFLAGS is set and defines a number of aggressive
checks and optimizations. This causes a build failure when generating a
GRUB2 boot loader image using the 'build_grub.sh' script.
Unsetting it within the script allows it to proceed and successfully
build a functional GRUB2 boot loader image to be used with Zephyr.
Fixes: #14289
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Updates the 96b_nitrogen board document to link to the new debugging
guide instead of the opensda page.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the usb_kw24d512 board
document to leverage the new debugging guide covering debug probes and
host tools.
This board does not have an OpenSDA microcontroller, therefore the only
debug probe currently supported is the external J-Link.
Updates the flashing section to reflect that the ``flash`` build system
target is now supported.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the lpcxpresso54114
board document to leverage the new debugging guide covering debug probes
and host tools.
This board supports the LPC-Link2 J-Link onboard debug probe.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the hexiwear board
documents to leverage the new debugging guide covering debug probes and
host tools.
Recommends the OpenSDA J-Link debug probe because the k64 and kw40z
share the same OpenSDA microcontroller, and the kw40z requires Segger
RTT for a console. It is possible to use daplink firmware for the k64,
however it is not recommended because it requires switching the firmware
back to jlink to access the kw40z.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hexiwear_k64f and hexiwear_kw40z share the same OpenSDA
microcontroller on the hexiwear docking station, so make the jlink the
default firmware on both for consistency. We use jlink instead of
daplink by default because hexiwear_kw40z can only use Segger RTT for
the console (there is no UART available).
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The frdm_kw41z board was originally configured in zephyr to use the
jlink runner by default because pyocd didn't yet support the kw41z soc.
Support for kw41z was added in pyocd v0.9.0, so we can now default to
daplink firmware and pyocd.
Now all freedom boards in zephyr consistently use daplink and pyocd.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the freedom board
documents to leverage the new debugging guide covering debug probes and
host tools.
These boards support OpenSDA DAPLink and OpenSDA J-Link onboard debug
probes. They can also support an external J-Link probe, but this
requires board modifications (cutting traces) and is therefore not
documented.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the mimxrt1060_evk and
mimxrt1064_evk board documents to leverage the new debugging guide
covering debug probes and host tools.
Neither of these boards have OpenSDA J-Link board-specific firmware,
therefore the only debug probe currently supported is the external
J-Link.
Updates the flashing section to reflect that the ``flash`` build system
target is now supported.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Reworks the programming and debugging section in the mimxrt1020_evk and
mimxrt1050_evk board documents to leverage the new debugging guide
covering debug probes and host tools.
These boards support both the OpenSDA J-Link onboard debug probe and the
J-Link external debug probe.
Corrects an error linking to the wrong OpenSDA J-Link firmware.
Updates the flashing section to reflect that the ``flash`` build system
target is now supported.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
* the original configurations are configured with stack checking
* the new configurations are configured with mpu stack guard
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The GPIO driver is required by this board's initialization code, hence
it is forced to be enabled always, not only enabled by default like on
other boards equipped with an nRF SoC.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This patch enables the GPIO driver by default on all boards equipped
with an nRF SoC (all boards having `CONFIG_SOC_FAMILY_NRF=y` in their
`_defconfig` file).
In vast majority of cases the driver is needed, so it is more
convenient to enable it at board level than in particular
applications.
And if the driver is undesired for some reason, it can be still
disabled in the application config.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Set FLASH_LOAD_OFFSET correctly (accounting for Nordic MBR) when
BOARD_HAS_NRF5_BOOTLOADER is defined and we're not compiling MCUboot.
MCUboot will select USE_CODE_PARTITION, which will make it link
correctly regardless of which board DTS is used (stock/debugger).
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Discovered with pylint3.
Use the placeholder name '_' for unproblematic unused variables. It's
what I'm used to, and pylint knows not to flag it.
Python tip:
for i in range(n):
some_list.append(0)
can be replaced with
some_list += n*[0]
Similarly, 3*'\t' gives '\t\t\t'.
(Relevant here because pylint flagged the loop index as unused.)
To do integer division in Python 3, use // instead of /.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
nrf52840_pca10056 and nrf52_pca10040 was enabling RTT by default
for all samples. It has some implications like forwarding printk
to logger and that, as a default behavior, may not be welcomed.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The nRF91 DK User Guide clearly says "the LEDs are active high,
meaning that writing a logical one ('1') to the output pin will
illuminate the LED".
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable TIMER1 by default in nrf9160_pca10090 so it can be selected
by user for hardware byte counting in UARTE or other purpose.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Making a clean slate for some pylint CI tests. Only enabling relatively
uncontroversial stuff.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Following fix SRAM size to take into account CCM,
enable CCM and update yaml files in boards including fixed soc
dtsi definitions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
One of the bullet list items didn't get rendered properly because
continuation line wasn't indented.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
As em7d is configured with HARVARD, CCM will be used not DDR,
SRAM should point to DCCM.
This bug will cause the wrong caculation of heap area,
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
When using V0.10.0 SDK, flashing is not working anymore on
stm32f4_disco.
Using st_nucleo_f4.cfg instead of stm32f4discovery.cfg solves
the issue.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move the original documentation in the arduino_101 board to a common
section in the Bluetooth documentation and document the use of `btmon`
in general.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add the bt-mon-uart chosen node to all the nRF-based boards so that they
can all use CONFIG_BT_DEBUG_MONITOR without additional changes.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Based on prior work by @dcpleung. It's suboptimal, but it provides a
working starting point for ACRN work. The x86 board/SoC abstractions
really need to be refactored to make this "board" (and other x86-based
"boards", both extant and future) cleaner and easier to maintain. Punt.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Added some more content to the section about how to simulate
with BabbleSim and a couple of extra links.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Fixes the apds9960 i2c address on the reel_board. Found while converting
the apds9960 driver to use the i2c address from device tree rather than
a hardcoded value in apds9960.h.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The current flash configurations for all nRF52840's in Zephyr is
VERY constrained when it comes to allowing samples any space for
storage or custom areas. It only leaves the last 4 pages of flash
for "storage".
The nRF52840 is also capable of using OpenThread which defaults
to using the last 4 pages of flash for storing OpenThread-related
network data.
This means that while using OpenThread under any configuration
designed to use mcuboot partition slots, there is no space left
over for storage of any kind.
Let's adjust the partition table to set storage at 8 pages of
flash (32k). This fixes the conflict with OpenThread and leaves
room for future use cases that may arise.
Signed-off-by: Michael Scott <mike@foundries.io>
It is also possible to use 'west' to build the 'hello_world' sample
application for the UP2 (up_squared) board. This patch makes it
explicit in the documentation.
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
USB is already being configured in pinmux.c, but for it to be
availiable it also needs to be enabled in the device tree.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This is a vestiage of how board ports use to work, we have since removed
the need for board.h to exist on all board ports. Remove the file since
its not needed and doesn't do anything useful.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* separate the ARC MPU driver into 2 parts
* arc_mpu_v2_internal.h for ARC MPUv2
* arc_mpu_v3_internal.h for ARC MPUv3
* For ARC MPUv2, keep the main design, but update and optimize the code
* For ARC MPUv3, implement mpu region split to supprt MPU region overlap
* misc updates and bug fixes
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Linking to API material requires knowing the pecularities of how
doxygen, sphinx, and breathe work. In an attempt to hide some of this
we're preparing the current docs to allow use of configuration defaults
that will let us more simply use a default role that will hunt for a
reference target in the various domains that are available by using a
default "role" of "all". This will let us use the simple notation
`functionname` or `typename` without fully specifying the reference as
:c:func:`functionname`.
This patch cleans up exising docs that were (incorrectly) using single
backtics where double backtics should have been used, and also found
some typos (such as a space between the role name and the reference,
such as :file: `filename`, and a missing colon such as
c:func:`functionname`)
This is a start to address issue #14313
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The build_grub.sh script cherry-picks 3 commits from the master branch
of grub because more recent build tools fail to build the latest stable
release (which is 2.02). This solves the problem on Fedora 29 for
example, but is not sufficient for Clear Linux.
This patch modifies the build_grub.sh script to use
grub-2.02-285-g5bc41db75 (latest from master as of 13 of March 2019).
That version compiles 'out-of-the-box' in the latest Ubuntu, Fedora and
Clear Linux.
There are additional tools required on the host system and the
documentation has been updated accordingly.
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Updates the documentation to show PC13 instead
of PB12 as deafult LED Pin. Also adds note
about the default LED based on version of board.
Includes the change that needs to be made to
the dts file for changing default LED pin
Signed-off-by: Suryansh Sharma <suryansh@evilscientist.cc>
efm32pg_stk3402a and lpcxpresso54114_m0 board yaml files didn't set
xtools under the toolchain category, fix that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We can turn this off in application code, but the default should be
SMP.
Oddball note: the SMP setting is in the soc layer and not arch, even
though I think it would be better there. We don't actually have a
per-arch defconfig file included by kconfig.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Add CONFIG_SYS_CLOCK_TICKS_PER_SEC=1000 to nucleo_l053r8_defconfig.
All STM32 boards seem to have this defined.
Makes samples with ksleep work properly.
Signed-off-by: Anthony Kreft <anthony.kreft@gmail.com>
Since NET_L2_BT no longer "select"s BT and the rest of required BT
features, enable them within the defconfig file.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Maybe this is some "just in case" thing that got copied around. There's
no need to have a blank line at the beginning or end of Kconfig files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Configure lvgl defaults for imx rt boards in their respective board
defconfigs rather than the lvgl sample application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This build target is intended to verify that enabling the
IAMCU ABI doesn't have any bit-rot since we can easily
run this under emulation.
However, the QEMU boards all derive from the generic IA32
SOC definition, which is any pc-like hardware. We need
to disable these mitigations for this target since the
IAMCU compiler doesn't even recognize instructions like
'lfence'.
Fixes: #14315
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Redefining the config will not let another (out-of-source) driver be
chosen instead of the default. The driver is practically forced by the
soc settings. This commit moves default settings from soc/arm/nordic_nrf
into the drivers themselves.
Signed-off-by: Thomas Stenersen <thomas.stenersen@nordicsemi.no>
Fedora 29 (and possibly other disctributions) are nowadays coming with
very recent versions of gcc (8.x) and binutils. These will cause some
compilation error when running the 'grub_build.sh' script to create a
GRUB2 boot loader image.
Fortunately, both issues have been fixed and merged in the upstream
project. This patch modifies the build script to cherry-pick those to
the local cloned version of grub before building it.
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Now that we have SDK 0.10.0 we can enable building this board with the
Zephyr toolchain. SDK 0.10.0 introduced support for the ARM v8m based
cores which these boards utilize.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update reserved function names starting with one underscore, replacing
them as follows:
'_k_' with 'z_'
'_K_' with 'Z_'
'_handler_' with 'z_handl_'
'_Cstart' with 'z_cstart'
'_Swap' with 'z_swap'
This renaming is done on both global and those static function names
in kernel/include and include/. Other static function names in kernel/
are renamed by removing the leading underscore. Other function names
not starting with any prefix listed above are renamed starting with
a 'z_' or 'Z_' prefix.
Function names starting with two or three leading underscores are not
automatcally renamed since these names will collide with the variants
with two or three leading underscores.
Various generator scripts have also been updated as well as perf,
linker and usb files. These are
drivers/serial/uart_handlers.c
include/linker/kobject-text.ld
kernel/include/syscall_handler.h
scripts/gen_kobject_list.py
scripts/gen_syscall_header.py
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Appears within an 'if BOARD_NRF52_BSIM' in the same file.
'if FOO' is just shorthand for adding 'depends on FOO' to each item
within the 'if'. Dependencies on menus work similarly. There are no
"conditional includes" in Kconfig, so 'if FOO' has no special meaning
around a source. Conditional includes wouldn't be possible, because an
if condition could include (directly or indirectly) forward references
to symbols not defined yet.
Tip: When adding a symbol, check its dependencies in the menuconfig
('ninja menuconfig', then / to jump to the symbol). The menuconfig also
shows how the file with the symbol got included, so if you see
duplicated dependencies, it's easy to hunt down where they come from.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Appears within an 'if BOARD_NATIVE_POSIX' in the same file.
'if FOO' is just shorthand for adding 'depends on FOO' to each item
within the 'if'. Dependencies on menus work similarly. There are no
"conditional includes" in Kconfig, so 'if FOO' has no special meaning
around a source. Conditional includes wouldn't be possible, because an
if condition could include (directly or indirectly) forward references
to symbols not defined yet.
Tip: When adding a symbol, check its dependencies in the menuconfig
('ninja menuconfig', then / to jump to the symbol). The menuconfig also
shows how the file with the symbol got included, so if you see
duplicated dependencies, it's easy to hunt down where they come from.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
A new role :zephyr_file: is available that renders to a link to the file
or folder in GitHub. Find appropriate references using :file: and
convert to :zephyr_file: to take advantage of its linking capability.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The nRF52840-based Particle.io boards have an external flash
module that is connected via SPI interface. Originally,
the goal was to place the flash part into deep power down
mode and save 9 uA in sleep mode, but this was never
implemented in a board initialization file.
Let's remove the default y behavior for SPI as each sample
will turn it on if needed, and it can cause certain out of
tree samples to behave badly (where CONFIG_MULTITHREADING=n).
Long term: we need a better solution for handling samples
that don't fit the requirements for certain drivers, but
for now this will clean up some board usability issues.
Signed-off-by: Michael Scott <mike@foundries.io>
Most of these are from source'ing a file within an 'if PINMUX', and then
adding another 'depends on PINMUX' within it.
'if FOO' is just shorthand for adding 'depends on FOO' to each item
within the 'if'. There are no "conditional includes" in Kconfig, so
'if FOO' has no special meaning around a 'source'. Conditional includes
wouldn't be possible, because an 'if' condition could include (directly
or indirectly) forward references to symbols not defined yet.
Tip: When adding a symbol, check its dependencies in the menuconfig
('ninja menuconfig', then / to jump to the symbol). The menuconfig also
shows how the file with the symbol got included, so if you see
duplicated dependencies, it's easy to hunt down where they come from.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
JLink V6.44 (2019-03-01) added support for the imx rt1064 soc, including
programming the internal flash on flexspi2. Updates the mimxrt1064_evk
board to use the internal flash and external sdram memories by default,
now that the debug tools support them.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Do not enable by default both I2C and SPI nodes for the peripherals
with the same instance number, since they use the same MMIO base
address and DTC will issue a warning in such situation.
This patch corrects dts files for the following boards:
- nrf51_pca10028
- nrf52_pca10040
- nrf52840_blip
- nrf52840_pca10056
- nrf52840_pca10059
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
SPI_0 cannot be used simultaneously with I2C_0, since in nRF52832 SoC
these instances share certain hardware resources.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
To build apps for mcuboot, a zephyr,code-partition needs to be
identified in the DTS chosen block. Without this entry, the
following configs will always be 0:
CONFIG_FLASH_LOAD_OFFSET
CONFIG_FLASH_LOAD_SIZE
Signed-off-by: Michael Scott <mike@foundries.io>
According with MISRA-C every switch-clause must terminate with an
unconditional break.
MISRA-C rules 16.1 and 16.3
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Reduce unnecessarily large images of boards (> 1MB)
Also fixed typo in doc title for mec2016evb_assy6797
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The creation of the udev rule requires the user to be root else
it will fail. Update the text of the documentation to make it clearer
and change the shell prompt of the command to '#'
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Added an assert in the logger thread in case there
is no backends, instead of having that thread spinning
forever. Disabled log in qemu_xtensa board due to lack
of backends.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
UART_QMSI_0_BAUDRATE was removed by commit 17c6456678 ("drivers/uart:
Use dts to set uart priorities for QMSI driver").
There's a reference to CONFIG_UART_QMSI_1_BAUDRATE as well, but getting
rid of it requires documentation updates.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
We expect that identifier in yaml will match board name for sanitycheck.
Change the identifier to match so sanitycheck runs propertly.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The MMIO addresses for peripherals are being assigned by BIOS
at boot. Different BIOS versions and number of enabled peripherals
affect how those addresses are assigned. This invalidates
the addresses for UART defined in DTS. Turn on PCI enumeration
so UART addresses are probed at boot to avoid non-usable
UART and black console.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Previous rename from CONFIG_* to DT_* left a few remaining
CONFIG_*. So rename them manually now.
Fix#13753
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
On nrf52810_pca10040 board, the nRF52810 SoC is emulated on nRF52832.
This patch overrides for this board the number of cycles consumed by
one iteration of the internal loop in `nrfx_coredep_delay_us()` (used
by `k_busy_wait()`), so that the value adequate for nRF52832 is used.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In the recent MDK brought by nrfx 1.6.2, these legacy peripherals have
been revealed as available also in nRF52810. This patch allows their
use in Zephyr drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The i.MX RT1064 evk has one ethernet (10/100M) connector via KSZ8081RNB
phy. Enable related dts nodes and config flags
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The command to create the board image binary file assumes the input
is always called zephyr.bin. This is not always the case if custom
name is defined in CONFIG_KERNEL_BIN_NAME. So update the call of
command to use CONFIG_KERNEL_BIN_NAME.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Recent versions of GCC won't build grub-2.02 because they're more
pedantic about warnings. This has been fixed upstream but is not
yet part of any release. The build script is modified to apply the
relevant commits before building.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This fix allows Renode to resemble the time flow of the hardware more
precisely. The performance value was established manually, there is no
indication in the docs on what is the average performance.
It allows tests/posix/common/portability.posix to pass, but fails on
tests/kernel/lifo/lifo_usage/kernel.lifo.usage.
The latter also fails on hardware.
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
This commit adds a patch in the Kconfig.defconfig file of
nRF9160_pca10090 board, that instructs the linker to restrict
the Secure image to the size of its code partition, if the
image is to be combined with a Non-Secure image. Secure images
without accompanying Non-Secure firmware (i.e. with symbol
TRUSTED_EXECUTION_SECURE not set) can use the entire flash.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We do not need to overwrite the reg property of flash0
in nrf9160_pca10090 default partitioning. The property
reflects the flash resources of the SOC, and is passed
in the .dtsi file of nRF9160 SOC definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Most of the other nRF52832 boards have the following settings for
scratch and storage partitions:
scratch_partition: partition@70000 {
label = "image-scratch";
reg = <0x00070000 0xa000>;
};
storage_partition: partition@7a000 {
label = "storage";
reg = <0x0007a000 0x00006000>;
};
Let's adjust the scratch size to align with the others and add the
storage partition so that settings and FS samples will work.
Signed-off-by: Michael Scott <mike@foundries.io>
The MPU should have been enabled on all these boards since they have
Cortex-M7 and need mpu for caching support.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Most of the other nRF52832 boards have the following settings for
scratch and storage partitions:
scratch_partition: partition@70000 {
label = "image-scratch";
reg = <0x00070000 0xa000>;
};
storage_partition: partition@7a000 {
label = "storage";
reg = <0x0007a000 0x00006000>;
};
Let's remove the snowflake settings in BLENano2 which coincidentally
are incorrect: storage overruns the flash area by 0x1000 and causes
a crash when enabling FCB storage.
Signed-off-by: Michael Scott <mike@foundries.io>
Remove most unnecessary instances of `export` and `cmake` use that can
instead be replaced with `zephyr-app-commands` or similar. This is to
avoid documentation using different mechanisms to describe the same
actions and in preparation for documenting `west build` everywhere.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Remove DCACHE_WRITEBACK Kconfig variable definition in Intel S1000
DMA driver. Remove the variable from default configuration as well.
Cache configuration is fixed and the cache operation routines
internally take appropriate action based on the cache configuration.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Added more detailed information how to connect Zephyr instance
to host system like Linux desktop.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The mimxrt1060_evk was missing hwinfo in the supported list. All other
imx rt boards already have it.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes Segger RTT on the hexiwear_kw40z and usb_kw24d512 boards by
setting CONFIG_RTT_CONSOLE=y and CONFIG_USE_SEGGER_RTT=y.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Comment for storage partition could be misleading.
Clarify this is a partition used for file system.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fix setting of the I2C bus master device name for the GPIO_PCAL9535A
device and PWM_PCA9685. We need to extract them from the dts otherwise
they will just get set to "".
Fixes#13458
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Refactor the imx rt code/data location config defaults such that we
default to on-chip memories at the soc level and override to external
memories at the board level. This means that we frequently override soc
defaults for evk boards, but it removes the assumption that all imx rt
boards (particularly non-evk boards) will have the same external
memories as evk boards.
The end result is that imx rt evk boards still have the same defaults as
before, but the way we get there is different.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enable pull-up on UART RX pin to reduce power consumption.
If the board is powered by battery and the debugger is
not connected via USB to the host, the SoC consumes up
to 2mA more than expected.
The consumption increases because RX pin is floating
(High-Impedance state of pin B from Dual-Supply Bus Transceiver).
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
There are issues using lowercase min and max macros when compiling a C++
application with a third-party toolchain such as GNU ARM Embedded when
using some STL headers i.e. <chrono>.
This is because there are actual C++ functions called min and max
defined in some of the STL headers and these macros interfere with them.
By changing the macros to UPPERCASE, which is consistent with almost all
other pre-processor macros this naming conflict is avoided.
All files that use these macros have been updated.
Signed-off-by: Carlos Stuart <carlosstuart1970@gmail.com>
This is a follow-up to commit e2b38e02bf.
Default PWM instances are enabled in Kconfig and DTS (with channel 0
set to LED0 pin) for these boards so that it is possible to build basic
samples blink_led and fade_led for them without extra modifications.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
For the native_posix board, and for the nrf52_bsim boards,
the sys_trace_irs_exit() call was missing. Add it.
Relates to #13357
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Following introduction of zephyr sdk0.10 and openocd branch
from from 20190130, stm32l4+ SoC support is now available and
flash and debug operations are available on nucleo_l4r5zi board.
Fixes 12094
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The imx rt family of socs has several options for linking code and data
into internal or external memories, and up until now we have handled
these options at the board level. This has resulted in several Kconfig
symbols being defined in multiple places and triggering warnings in
documentation builds:
warning: the default selection CODE_ITCM (defined at boards/arm/mimxrt1050_evk/Kconfig:13, boards/arm/mimxrt1060_evk/Kconfig:13) of <choice> (defined at boards/arm/mimxrt1050_evk/Kconfig:9) is not contained in the choice
warning: the choice symbol CODE_ITCM (defined at boards/arm/mimxrt1050_evk/Kconfig:13, boards/arm/mimxrt1060_evk/Kconfig:13) is defined with a prompt outside the choice
warning: the choice symbol CODE_HYPERFLASH (defined at boards/arm/mimxrt1050_evk/Kconfig:16, boards/arm/mimxrt1060_evk/Kconfig:16) is defined with a prompt outside the choice
warning: the choice symbol CODE_QSPI (defined at boards/arm/mimxrt1050_evk/Kconfig:19, boards/arm/mimxrt1060_evk/Kconfig:19) is defined with a prompt outside the choice
warning: the choice symbol CODE_ITCM (defined at boards/arm/mimxrt1050_evk/Kconfig:13, boards/arm/mimxrt1060_evk/Kconfig:13) is defined with a prompt outside the choice
warning: the choice symbol CODE_HYPERFLASH (defined at boards/arm/mimxrt1050_evk/Kconfig:16, boards/arm/mimxrt1060_evk/Kconfig:16) is defined with a prompt outside the choice
warning: the choice symbol CODE_QSPI (defined at boards/arm/mimxrt1050_evk/Kconfig:19, boards/arm/mimxrt1060_evk/Kconfig:19) is defined with a prompt outside the choice
The number of warnings increased as we added more imx rt boards. Fix the
warnings by moving code and data location configs from the board level
to the soc level.
The default memories for all imx rt boards are unchanged. The
mimxrt10{20,50,60}_evk boards still default to hyperflash/qspi for code
and sdram for data. The mimxrt1064_evk board still defaults to ITCM for
code and DTCM for data because jlink does not yet support programming
internal flash.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add nvs support to nucleo_f091rc board. This requires to
add erase-block-size property to stm32f0.dtsi.
Storage partition is set to 4kb at the end of the flash.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The ICCM/DCCM defines come from DT so they should be DT_ prefixed and
not CONFIG_ prefixed. Fix that in arc_mpu_regions.c.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a space in some long doc titles to allow for wrapping in the title
display. Also fixed a table in the mec2016evb board doc.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Print just the basename of the Input and Output filenames
when creating the board specific image for Intel S1000 CRB
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Be consistent in how board docs are named and move all to index.rst.
This will make the URL to the board documentation predictable and easier
to remember.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The phrase "Zephyr applications use the ..." in many boards and
inconsistently. This is just to say what is the board identify is.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This was tested with a the hello world application. UART 0 was used
as console for displaying "Hello World! mec2016evb_assy6797" to the
a serial terminal.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
The board pinmux code has been using non DT_ prefixed defines for DT
generated defines. Switch to use DT_ prefixed ones as we want to
deprecated the non DT_ prefixed defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Document the `west build` command in the section corresponding to the
west commands that deal with the CMake cache, which is now named
"Building, flashing and debugging" for consistency.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The values for the registers like GDV, SDV and Boarder Waveform
depend on the panel and display controller. Add DT properties
and obtain such values from DT.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
We want a _Swap() variant that can atomically release/restore a
spinlock state in addition to the legacy irqlock. The function as it
was is now named "_Swap_irqlock()", while _Swap() now refers to a
spinlock and takes two arguments. The former will be going away once
existing users (not that many! Swap() is an internal API, and the
long port away from legacy irqlocking is going to be happening mostly
in drivers) are ported to spinlocks.
Obviously on uniprocessor setups, these produce identical code. But
SMP requires that the correct API be used to maintain the global lock.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Adding a set of BKMs on how to enable and configure UART1
for the nrf52840_pca10056 board. This instructions are likely valid
to most other nrf52840- family of boards.
Signed-off-by: Andrei Laperie <andrei.laperie@intel.com>
This commit enables the PWM0 device on the Atmel SMART SAM E70 Xplained
Board, by adding the entries to the DTS and configuring the PWM pins
from the EXT1 connector (channel 0, inverted) and EXT2 connector
(channel 2, inverted and non-inverted) with the corresponding peripheral
functions. It also updates the documentation and mark pwm as supported
for the tests.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We've removed the QMSI RTC driver as part of the new counter API. So
any old rtc tests don't build for QMSI based boards anymore. Switch
this from 'rtc' to 'counter' in the board.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This was never a long-term solution, more of a gross hack
to get test cases working until we could figure out a good
end-to-end solution for memory domains that generated
appropriate linker sections. Now that we have this with
the app shared memory feature, and have converted all tests
to remove it, delete this feature.
To date all userspace APIs have been tagged as 'experimental'
which sidesteps deprecation policies.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Instead of enabling Bluetooth by default on nRF5x boards, only enable
the controller if Bluetooth has been enabled by the applicaiton.
Fixes#5454Fixes#12215
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Few boards supporting RTC were missing rtc as supported rtc feature
in yaml files. Fix this.
Add counter to all boards supporting rtc as RTC IP now support
both rtc and counter API.
Change split in 3 parts in order to lower CI load and get shippable
happy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Few boards supporting RTC were missing rtc as supported rtc feature
in yaml files. Fix this.
Add counter to all boards supporting rtc as RTC IP now support
both rtc and counter API.
Change split in 3 parts in order to lower CI load and get shippable
happy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Few boards supporting RTC were missing rtc as supported rtc feature
in yaml files. Fix this.
Add counter to all boards supporting rtc as RTC IP now support
both rtc and counter API.
Change split in 3 parts in order to lower CI load and get shippable
happy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Configure RTC on nucleo_f746zg.
It is supported through counter RTC API.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable testing of counter (COUNTER_{D}TMR_CMSDK) on mps2_an385 and
enable timers on v2m_beetle (TIMER_{D}TMR_CMSDK).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CMSDK Dual Timer can be used as a timer or as a counter.
The unified interface proposed in #8340 unifies counter.h and rtc.h to
provide a common interface.
This patch modifies the timer implementation of the dual timer to
make it compliant with the new proposed interface.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CMSDK Timer can be used as a timer or as a counter.
The unified interface proposed in #8340 unifies counter.h and rtc.h to
provide a common interface.
This patch modifies the timer implementation of the single timer to
make it compliant with the new proposed interface.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enabled EPIT (Enhanced Periodic Interrupt Timer) in Cortex-M4 core
of Udoo Neo Full board so the counter API could be used there.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Add driver support for kinetis ID device.
The length depends on the SoC.
`SIM_GetUniqueId` was not used because the struct would reorder
the ID and makes the driver more complicated because the length
of the struct depends on the SoC.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Adds device tree bindings and nodes for the rocktech lcd module used on
imx rt boards. The use of port, endpoint, and remote-endpoint properties
follow what is currently done in linux, but they are not yet used in
zephyr because some additional plumbing is needed in the
extract_dts_includes.py script.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Always link firmware built for nrf9160_pca10090ns into the
code-partition defined in DT, regardless.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Introduce BOARD_NRF9160_PCA10090NS to differentiate between
secure and non-secure board variants.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
When selecting BT we need to select BT_CTRL for most bluetooth
samples to work correctly.
Let's fix that in the board files.
Fixes the following error when CONFIG_BT is selected:
zephyr/drivers/bluetooth/hci/h4.c:463:30:
error: ‘CONFIG_BT_UART_ON_DEV_NAME’ undeclared (first use in
this function)
h4_dev = device_get_binding(CONFIG_BT_UART_ON_DEV_NAME);
^~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Michael Scott <mike@foundries.io>
Enable the SPI driver on the HiFive 1
This makes the following configurations choices for the HiFive 1:
The SPI 0 peripheral driver is not enabled by default because it is in
charge of mapping the SPI flash into memory. This can be configured
using the CONFIG_SIFIVE_SPI_0_ROM KConfig option.
The SPI 1 peripheral driver is enabled by default and the pinmux is
configured for all of its outputs
The SPI 2 peripheral driver is enabled by default because it is present
in the DTS for the FE310, but because the QFN48 package used on the
HiFive 1 doesn't route those pins from the silicon die, the pinmux can't
enable the SPI 2 pins.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Indicate that PWM is supported on several Nordic DK boards so that
the pwm_nrf5_sw and pwm_nrfx drivers are covered by CI builds.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable HW PWM driver instead of the SW one on nRF SoCs where the PWM
peripheral is present.
Default PWM instances are also enabled on Nordic DK boards so that it
is possible to build the basic fade_led sample for them without extra
adjustments.
After the above changes are applied, some configuration alterations
in basic samples blink_led and fade_led become no longer needed.
These are removed. And the blink_led sample is corrected so that it
works with the nRF HW PWM driver as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
To avoid confusion, callbacks using ordinal pin numbers
is going to be reverted. So the driver has to be re-worked
to expose multiple devices so each device has 32 pins.
Also fixes#12765
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This allows the shared_irq driver to be configured by device tree.
With previous implementation, only the board configuration can
override the IRQ trigger, as the trigger config is a "choice" rather
than "config". With this patch, the driver can be fully configued at
the SoC level.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
PAE tables introduce the NX bit which is very desirable
from a security perspetive, back in 1995.
PAE tables are larger, but we are not targeting x86 memory
protection for RAM constrained devices.
Remove the old style 32-bit tables to make the x86 port
easier to maintain.
Renamed some verbosely named data structures, and fixed
incorrect number of entries for the page directory
pointer table.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Indicate that watchdog is supported on several Nordic DK boards
so that the wdt_nrfx driver is covered by CI builds.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Changes the default code location from internal itcm to external qspi or
hyperflash. Changes the default data location from internal dtcm to
external sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Changes the default code location from internal itcm to external qspi.
Changes the default data location from internal dtcm to external sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new configuration option to mimxrt10{20,60,64}_evk boards to link
data into external sdram. The default remains to link data into internal
data tightly coupled memory (DTCM).
Note that mimxrt1050_evk is not included because it already has support
for linking data into sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Unlinke nucleo or disco boards, ST-Link Tx/Rx pins used for Virtual
Com Port is not connected to the chip.
Then, console is not available by default and one should use a serial
cable to enjoy console. Adding mention of this fact to the board
documentation and replacing default hello_world example by blinky,
since blinky sample works without any additional hardware.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Somehow these were getting generated as `FLASH_foo_BLOCK_SIZE` even
though there's no specification for them in the original yaml. Put them
back until we can figure out what's going on.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
In #9717, 777407b9ea
coverage support was broken for all NATIVE_APPLICATION except
native_posix
This includes the nrf52_bsim board
Fix it.
Fixes: #13009
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The disco_l475_iot1 board should be using CONFIG_USB_DC_STM32 as the
Kconfig sybmol.
Also fix a minor typo in a comment in nucleo_f207zg with regards to
CONFIG_USB_DC_STM32
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
From the driver point of view, monochrome controllers from the ssd16xx
family mostly differ by the amount of row and columns that are
supported. If they support more than 256 rows and/or columns the
corresponding size or position is sent using 2 bytes instead of 1 byte.
This patch therefore adds the width-bits and height-bits DT properties
to make this configurable.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that stm32 watchdog should be configured by device tree,
update dts file of boards declaring watchdog support.
Additionally update doc and yaml files.
Add support on some boards that were used to validate the driver
update:
- disco_l475_iot1
- nucleo_f207zg
- nucleo_f429zi
- nucleo_f746zg
- nucleo_f073rz
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert the hci_spi sample to get the SPI and GPIO settings from Device
Tree instead of Kconfig.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert the HCI SPI driver to get the SPI and GPIO settings from Device
Tree instead of Kconfig. The "zephyr,bt-hci-spi" binding is used as
a common one for this purpose ("st,spbtle-rf" is removed), to take
advantage of the new DT_<COMPAT>_<INSTANCE> generated macros and get
rid of related fixups and aliases.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Now that all supported xtensa boards use DTS we can move the Kconfig
setting to the arch level. Remove HAS_DTS from board Kconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The dts files on these boards had some CONFIG_ defines related to which
memory should be used to hold code. We move this choice out of DTS and
back into Kconfig.
As such, we removed the default setting of 'zephyr,flash' and just
map
CONFIG_CODE_ITCM to:
DT_NXP_IMX_RT_ITCM_0_SIZE
DT_NXP_IMX_RT_ITCM_0_BASE_ADDRESS
CONFIG_CODE_{QSPI,HYPERFLASH} to:
DT_NXP_IMX_FLEXSPI_402A8000_SIZE_1
DT_NXP_IMX_FLEXSPI_402A8000_BASE_ADDDRESS_1
for the mimxrt1050_evk, we remove the default setting of 'zephyr,sram'
and just map:
CONFIG_DATA_DTCM to:
DT_NXP_IMX_DTCM_0_SIZE
DT_NXP_IMX_DTCM_0_BASE_ADDRESS
CONFIG_DATA_SDRAM to:
DT_MMIO_SRAM_80000000_SIZE
DT_MMIO_SRAM_80000000_BASE_ADDRESS
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the how enabling of CONFIG_XIP impacts CONFIG_FLASH_SIZE and
CONFIG_FLASH_BASE_ADDRESS to Kconfig instead of dts.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As we want to remove dts dependency on Kconfig, we had a case based on
CONFIG_BOOTLOADER_MCUBOOT. From a DTS point of view that was just
getting the chosen property 'zephyr,code-partition' set. We can easily
move this to the actual dts files and remove the mcuboot.overlay.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit implements a CTF-backend for Zephyr's tracing API.
The CTF-backend itself is split in a middle-layer and a bottom-layer.
- Middle-layer decides the payload in event transactions,
- Bottom-layer implements the IO transport.
A simple POSIX bottom-layer is provided so far.
Signed-off-by: François Delawarde <fnde@oticon.com>
Change compatible, move the JEDEC ID from Kconfig to DTS, convert DTS
size from bytes to bits, remove unreferenced DTS properties. Remove DTS
fixups.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
All Particle mesh devices have an on-board 32 Mibit JEDEC-compatible
flash from GigaDevice. Add bindings to access it.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Use auto-generated device tree macros in LPS25HB driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DS0 driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Previously, only led0 was enabled.
This allows the samples/basic/disco sample to build/run for
this board.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Convert usb_dc_stm32 driver GPIO disconnect to use new defines so we
can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This board is unmaintained and unsupported. It is not known to work and
has lots of conditional code across the tree that makes code
unmaintainable.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Boot PHY initialization timeout, caching mechanism fixes and networking
buffer descriptors moved to no cache section. Enabled cache management
in networking driver and manual barriers.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Since the lp3943 led driver still supports both DTS and non-DTS
configuration, we update the code to use DT_<COMPAT>_<INSTANCE>
defines for the CONFIG_HAS_DTS_I2C case.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the new DT_<COMPAT>_<INSTANCE>_<PROP> defines to instantiate
devices. This commit adds also ability to define individual pin
locations on SoC series that support the feature. Definitions of GPIO
pins assigned to a given location have been moved from soc_pinmap.h file
to board DTS file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This patchset introduces support for building a board specific custom
image for intel_s1000_crb. This pads the output binary (zephyr.bin)
with some additional data as required by the s1000 BootROM.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
pinmux dev isn't really used or supported. We only have one driver that
is implmeneted, and that driver isn't ever enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert ssd1673 display driver to use new defines so we can remove
the dts_fixup.h code for it. Also dropped "-spi" from compatible.
Fix up references in reel_board dts and sample.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add sam0_rtc_driver that implements system timer API on top of the RTC
and can be used as a replacement for the default systick timer.
Signed-off-by: Martin Benda <martin.benda@omsquare.com>
The pins connected to the sensors and microsd card on board
were mapped to SPI_0 and I2C_0, but for nrf52 chips they
cannot both be used together.
Blip is yet unreleased, so change will not affect anyone really.
Signed-off-by: Tavish Naruka <tavishnaruka@gmail.com>
Changed 'in place' mode to bypass logger system and directly
call active backends. With this approach memory footprint of
the logger can be significantly reduced in terms of RAM and ROM.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
From the documentation of the SoC and the DevKit it turns out that
there's no hardware PWM controller.
Signed-off-by: Francesco Franchina <cescus92@gmail.com>
Fix the following dtc warnings on S1000:
Warning (simple_bus_reg): /soc/pinmux@81C30: simple-bus unit
address format error, expected "81c30"
Warning (alias_paths): /aliases: aliases property name must
include only lowercase and '-'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use auto-generated device tree macros in LIS3MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LIS2MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DSL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Added UART4 alternate pin function for L4 µC for PC10 and PC11.
Corrected naming of previously defined UART4 TX and RX defines.
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
A comment which had been copied straight from the native_posix
board refered to the nrf52_bsim board as native_posix,
which it is not, and may confuse users.
Fix it.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Add support for nrf52840_pca10090, i.e. the nRF52840 SoC on the
pca10090 development kit. The SoC is tasked to route some of the
nRF9160 pins to different components on the development kit.
Additionally, it can be used as a Bluetooth HCI device.
The routing options appear under "Board config" in Kconfig.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
This commit adds the initial documentation information
for board nrf9160_pca10090.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes the Kconfig and DTS board definition
files for nrf9160_pca10090ns board. This Zephyr board shall be
used to build Non-Secure Zephyr applications on nrf9160_pca10090
Dev Kit.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit contributes the Kconfig and DTS files for the
nrf9160_pca10090 board definition. The nrf9160_pca10090 board
shall be used to build Zephyr applications, running in Secure
mode, on nRF9160_PCA10090 Dev Kit.
Additionally, the commit introduces a default Secure and
Non-Secure flash partition configuration for the
nRF9160_PCA10090 board, allowing to use Zephyr for building
both the Secure and Non-Secure firmware images.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This board directory supports the RV32M1 Vega board when targeting
a RISC-V CPU core on the main SoC.
Currently, only RI5CY support is provided via the rv32m1_vega_ri5cy
board name.
Signed-off-by: Marti Bolivar <marti@foundries.io>
Signed-off-by: Michael Scott <mike@foundries.io>
Some extensions to the multi-level interrupt controller are required
to support SoCs with more than four level 2 interrupt "aggregators".
Extend existing support to allow at most 8 level 2 or level 3
aggregators. Use Kconfig macro templates to cut down on boilerplate.
Try to clarify some aspects of the Kconfig help while we're at it, and
change the type of options which count things or are table offsets
from "hex" to "int", so that the generated .config is easier to read.
Finally, make some improvements to gen_isr_tables.py while we are
here. In particular, move some assignments around to cut down on
duplicated work, don't check for symbols we know must exist, and
improve the debug logging output's readability.
Signed-off-by: Marti Bolivar <marti@foundries.io>
If we are setting the code to be in HyperFlash (CONFIG_CODE_HYPERFLASH)
or QSPI (CONFIG_CODE_QSPI) we should enable
CONFIG_NXP_IMX_RT_BOOT_HEADER.
Update mimxrt1064_evk to use select like other boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add LSM303AGR ecompass (accelerometer + magnetometer) sensor support.
The LSM303AGR accelerometer and LSM303AGR magnetometer are s/w
compatible with respectively LIS2DH and LIS2MDL sensors and can
share same driver with those sensors.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add board support files for mimxrt1064_evk, the development board for
i.MXRT1064 (CM7) SoC.
- Add pinmux, dts, doc.
- Code can be loaded to SRAM.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
Share lis2dh driver among few accelerometer sensors that has
same register interface: LIS2DH, LIS3DH, LSM303DLHC, LIS2DH12,
LSM303AGR.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Move to using the generated DT_INVENTEK_ESWIFI_ESWIFI0_CS_GPIO_pin and
DT_INVENTEK_ESWIFI_ESWIFI0_CS_GPIO_CONTROLLER defines and drop the
DT_ESWIFI0_CS_GPIOS_PIN & DT_INVENTEK_ESWIFI_ESWIFI0_CS_GPIO_PIN from
dts_fixup.hl
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Supported PWM at pins A0, D3, D5 and D6 which are also Arduino
compatible. Also the onboard red LED can be used with PWM.
The basic/{fade_led, blink_led} samples to apply to this board
seemlessly and operate on the onboard red LED.
Also supported RTC.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
This commit adds the simplest configuration for this Nucleo-144 board
stripped down to the parts that are currently tested.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
Provide through the dts the gpio on which the lsm6dsl INT1 is
connected. Enable also the lsm6dsl trigger mode.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Enables the mcux lpi2c shim driver and pin muxes on the mimxrt1020_evk
board for LPI2C1 and LPI2C4. LPI2C1 is shared between the Arduino
connector J18 and the WM8960 codec. LPI2C4 is shared between the Arduino
connector J19 and the FXOS8700CQ sensor (non-populated by default).
Updates the board documentation and yaml supported list accordingly.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Enables the mcux ethernet driver and pin muxes on the mimxrt1020_evk
board, the same way it is done on the mimxrt1050_evk board. Updates the
board documentation and yaml supported list accordingly.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
mps2_an385 is enabled for networking -> default networking is SLIP ->
SLIP selects UART_PIPE -> UART_PIPE requires UART_PIPE_ON_DEV defined
-> undefined leads to error on building some samples.
Fix all of these issues.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Board can be emulated in QEMU, so select QEMU_TARGET as required for
various bits of "make run" magic to work.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The board has SMSC LAN9220 (actually as an "IP core" in an
FPGA-emulated SoC). The patch includes DTS bindings for this device.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Incoming updates to the nRF clock driver require some extra enum
definitions from the nRFx HAL which were not available in HW
model versions before 1.4 => update it.
Also as the nrf52_bsim does not yet support DTS, include a define
for the clock IRQ interrupt number (as the new clock driver will
be using the DTS macro instead of the nRF MDK value.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
board.h does not exist for any of the (official) Nordic nRF
boards. This commit corrects the information about the source
ofthe button and LED definitions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Remove all references in the documentation and Kconfig options
to the legacy shell to avoid confusing users and developers
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Adds an fxos8700 device tree node to the mimxrt1050_evk. The sensor
interrupt gpios require a board modification to be used and conflict
with Ethernet and LCD signals, therefore their pinmuxes are not
configured.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the mcux lpi2c shim driver and pin muxes on the mimxrt1050_evk
board. Updates the board documentation and yaml supported list
accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The schematic shows that both INT1 & INT2 from the MMA8652FC are wired
up, update the dts to reflect this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert lsm303dlhc_accel & lsm303dlhc_magn sensor driver to use new
defines so we can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configuration of Erase command is specified in DTS. Hence
the corresponding changes in Kconfig are removed.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Number of sectors is now calculated from the flash density
i.e. (Flash size)/(sector size).
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
The starting 192kB SRAM is reserved for the mcubootloader. Exclude
this region while building an application to be loaded by mcubootloader.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
FIFO_DEPTH should be in the SoC's Kconfig as this is a
configuration of SPI master controller in SoC.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
This patchset introduces partitioning of flash in terms of blocks
(flash page layout) for s1000. This partitioning is currently to
be used for mcubootloader.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Use DT_ instead of CONFIG_ for spi freq, spi bus name, flash device
name and flash base address.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Update boards yaml file with arduino_i2c supported option
We exclude disco_l475_iot1 from the x_nucleo_iks01a1 sample since there
are duplicated sensors between the disco_l475_iot1 and shield. Until
Zephyr drivers can handle multiple sensors we need to have this exclude.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables instance 3 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1060_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables instance 2 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1020_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This board has headers for these buses so they should be made available
without requiring special overlays.
Also take advantage of the new Nordic auto-enable for peripherals,
which eliminates the need for special configuration.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Not all boards can get the coverage reports. The report generation
needs minimum of 64KB SRAM. This patch added support for mps2_an385,
qemu_cortex_m3, qemu_x86. This is just a subset. Also the previously
supported board native_posix is included in this patch.
If a board has 64KB RAM, it can generate reports by just
adding HAS_COVERAGE_SUPPORT in Kconfig.board.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Support musca board as a variant, it is a Cortex-M33 based SoC.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Signed-off-by: Minos Galanakis <minos.galanakis@arm.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit renames the CLOCK_CONTROL_NRF5 Kconfig symbol to
CLOCK_CONTROL_NRF. The change is required to aleviates confusion
when selecting the symbol in nRF9160 SOC definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Update nucleo_l073rz to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update doc
- update yaml
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_l053r8 to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f446re to fit with default configuration guidelines:
- add spi support
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update yaml
- disable I2C by default
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f411re to fit with default configuration guidelines:
- add spi support
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update yaml
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f401re to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- disable I2C and PWM by default
- update yaml
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f302r8 to fit with default configuration guidelines:
- remove reference to arduino_serial as Ardiuno D1/D0 are actually
mapped on PA2/PA3 which are already used for ST_Link com port,
hence not available by default for arduino serial
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f070rb to fit with default configuration guidelines:
-configure arduino spi and i2c
-update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The test suite will use the m2gl025_miv.resc Renode script to load the
platform.
Signed-off-by: Dawid Wojciechowski <dwojciechowski@internships.antmicro.com>
Signed-off-by: Jan Kowalewski <jkowalewski@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
For normal (over-the-wire) mode of CAN sample lowering bitrate to
125000 to ensure reliable transfer on stm32f072b_disco boards
Signed-off-by: Andrei Laperie <andrei.laperie@intel.com>
Increase the size of the MCUBoot flash partition in the fstab-debugger
partition table, to accommodate for the RTT console and logs.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The MCUBoot partition in the default partition table (fstab-stock)
is not meant to accommodate an RTT console, since the board does
not have a SEGGER chip.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Provide a dtsi file that sets up common capabilities for all
Feather-based Particle Mesh devices. Provide additional dtsi files for
some obvious peripheral options.
Remove the xtensa esp32 image: it didn't build, and there's no
indication of how the ESP32 firmware can be updated on the Argon board.
Use particle_argon as the nRF52840 side of the board.
Add Particle Boron support.
Note that dtsi files must be replicated in each board directory until
tooling supports DTS includes from a shared area.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This patch adds a x86_64 architecture and qemu_x86_64 board to Zephyr.
Only the basic architecture support needed to run 64 bit code is
added; no drivers are added, though a low-level console exists and is
wired to printk().
The support is built on top of a "X86 underkernel" layer, which can be
built in isolation as a unit test on a Linux host.
Limitations:
+ Right now the SDK lacks an x86_64 toolchain. The build will fall
back to a host toolchain if it finds no cross compiler defined,
which is tested to work on gcc 8.2.1 right now.
+ No x87/SSE/AVX usage is allowed. This is a stronger limitation than
other architectures where the instructions work from one thread even
if the context switch code doesn't support it. We are passing
-no-sse to prevent gcc from automatically generating SSE
instructions for non-floating-point purposes, which has the side
effect of changing the ABI. Future work to handle the FPU registers
will need to be combined with an "application" ABI distinct from the
kernel one (or just to require USERSPACE).
+ Paging is enabled (it has to be in long mode), but is a 1:1 mapping
of all memory. No MMU/USERSPACE support yet.
+ We are building with -mno-red-zone for stack size reasons, but this
is a valuable optimization. Enabling it requires automatic stack
switching, which requires a TSS, which means it has to happen after
MMU support.
+ The OS runs in 64 bit mode, but for compatibility reasons is
compiled to the 32 bit "X32" ABI. So while the full 64 bit
registers and instruction set are available, C pointers are 32 bits
long and Zephyr is constrained to run in the bottom 4G of memory.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Fix the QSPI and hyperflash nodes to be proper SPI children and expose
the address range for direct access as part of the controller's reg
region.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* i2c, spi, gpio are not tested, remove them now.
* fix the license issue in openocd.cfg
* fix the shell related setting
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The initial support of iotdk which is a board based on Synopsys
ARC IoT SoC.
In this commit, it includes
* processor support
* UART driver
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The mimxrt1020_evk and mimxrt1060_evk boards had invalid jlink device
names. Debugging via 'ninja debug' now works on these boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes a Kconfig typo in the mimxrt1060_evk board that was introduced
when the board was split into separate hyperflash and qspi
configurations.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moves the default TEXT_SECTION_OFFSET from the board level to the soc
level for the imx rt series. This offset is used to reserve space for
the imx boot header for external xip flash images.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add the codec reset GPIO to intel_s1000_crb's DTS
Update the DTS fixup for intel_s1000_crb accordingly
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Add board support files for mimxrt1020_evk, the development board for
i.MXRT1021 (CM7) SoC.
- Add pinmux, dts, doc.
- Code can be loaded to SRAM.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
Convert the w25qxxdv driver to use device tree for SPI device params.
Updated the Arduino 101 config to use device tree to specify the SPI
flash. Update the arduino_101_sss to drop Kconfig support for the
w25qxxdv flash.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
By default, after reset SWO signal is not connected to GPIO pin.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By default, after reset SWO signal is not connected to GPIO pin. This
commit adds required initialization code to enable support for SWO
logger. Not all SoC series support the feature.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
lpuart1 is the default port used by ST-Link VPC.
Update board description to match out of box board configuration.
Fixes#12092
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following recent renaming of STM32 UART Kconfig UART symbols,
LPUART was named as UART_LPUART_1.
Rename to LPUART_1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
* Add DTS support for gpio controller driver
Signed-off-by: Ashokkumar B <ashokkumar@zilogic.com>
Signed-off-by: Subash G <subash@zilogic.com>
Signed-off-by: Vishnu K <vishnu@zilogic.com>
Signed-off-by: Vaishnavi D <vaishnavi.d@zilogic.com>
By adding 'aliases' node in SoC .dtsi file it is possible to generate
DT_ defines which specify a logical name rather than relay on module
location on APB bus. E.g. DT_SILABS_GECKO_USART_40010000_LABEL becomes
DT_SILABS_GECKO_USART_USART_0_LABEL. Thus it is possible to remove
dts_fixup.h defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
In 4940a3cac2 a compile time
check of the HW model version was added. This check worked
fine for cases in which the problem was that people had not
fetched a new enough version of the HW models.
But in some cases people will have fetched a new enough version
but be (unknowingly) in a past detached HEAD (or old tag).
With this change we ensure that the required tag is an actual
ancestor for the current HW models version HEAD
Also fail with an error, instead of just printing a warning.
Users can still disable this warning if they know what they are
doing.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The i2c_atmel_sam3 driver was deprecated at release 1.9, this commit
removes it. Also pinmux_dev_atmel_sam3x driver is removed.
i2c_atmel_sam3 was the last one which depended on it.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Remove configuration parameter CONFIG_BUS_TYPE. Now we may
make use of DT_ST_LSM6DSL_BUS_I2C and DT_ST_LSM6DSL_BUS_SPI
definition to select the bus.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
With this change, drivers or components can register on runtime
their own command line arguments.
What this change does is to use the dynamic command line arguments
API from BabbleSim's libUtil and provides a function for the
drivers to add their own.
Note that this change requires v1.3 of the HW models (which remove
a dependency on the board command line arguments structure)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This function can only be used when the arguments structure memory
layout starts as in bs_basic_dev_args_t.
This assumption is just too dangerous in this board as somebody
may change the structure in the future unaware of this weird
requirement.
=> Do not use this function but do what it does in place.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
When the -nosim option is used the user may still want to set
either the simulation ID string (-s) or the device number (-d)
to control the tracing prefixes and/or dump folder, but may not
care to set both of them.
=> This change allows it, while the old behaviour is otherwise
maintained (setting both or none with -nosim)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Updated flash partitions to extend supported boot scenarios.
Add support for using Nordic nRF5 bootloader to:
- flash a Zephyr application
- flash a MCUboot image as an application
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The en.high-perf_nucleo-144_mbed.jpg is an empty file.
This causes error when generating PDF documentation
as the tool cannot deal with empty image files.
So replace it with the image with same filename from
nucleo_f765zg, as the images are identical from
the online product description pages.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
interface/stlink-v2-1.cfg and interface/stlink-v2.cfg are wrappers
around interface/stlink.cfg, their inclusion trigger warning which
this change addresses. Besides the warning there is nothing there
except sourcing iterface/stlink.cfg directly.
Signed-off-by: Vasili Slapik <vslapik@gmail.com>
This mode allows the USB driver to use MSI clock as source clock.
MSI PLL-Mode permits +/-0,25% accuracy.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The L476RG does not use the same I2C instance as the other L4 boards.
Correct the pinmux and add the peripheral.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
patch set the config USB_DFU_MAX_XFER_SIZE to 4096. This will
reduce the time required for flashing.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Document CAN support for board nucleo_l432kc and
add can to board yaml "support" section.
Fixes#12052
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fix misspellings in documentation (.rst, Kconfig help text, and .h
doxygen API comments), missed during regular reviews.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Enable by default the following hardware instances in Kconfig:
- ADC_0
- I2C_0
- SPI_1 (SPI_0 for nRF52810)
for all nRF development kit boards having the corresponding DT nodes
enabled. This way there is no need to enable these instances in
particular applications, like samples for sensors or tests for drivers.
I2C_0 and SPI_0 cannot be used simultaneously in most of nRF SoCs,
nRF52810 is the only exception so far (and in this SoC SPI_1 is not
present, hence SPI_0 is enabled for it).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The options selecting nRF drivers are now enabled by default when
an nRF SoC is selected as the build target.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Fixes board PHY initialization.
ENET_RST and ENET_INT pins are also used as USER_LED/JTAG_TDI and
INT1_COMBO/JTAG_TDO. Initialization needs to set these pins to power and
interrupt for the PHY Transciver. PHY reset works without busy waiting.
Moved pin initialization back to PRE_KERNEL_1 to fix UART bug and busy
wait not required.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Added support for SPI 1 available from the arduino connector (plus an
extra gpio). Tested against samples/sensor/bme280.
Added warnings in documentation, pinmux and dts highlighting a potential
conflict if using SPI_1 and on-board ethernet at the same time.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Added board definitions for nucleo_f756zg. Features include gpio,
pinmux, uart (ST Zio, ST-Link and Arduino Uno v3 interfaces).
Added basic documentation and some soc definitions for the
stm32 f756XX soc.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Updated .dts and pinmux.c to highlight pin conflict on PA7 if ETH and
SPI_1 are selected together without modification.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch cleans up the code in the recently added dts_fixup.h,
restoring the original alignment of the file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The dts.fixup for mps2_an385 contains a wrong setting for the IRQ fixup
for the Dual Timer IRQ.
This patch fixes the symbol included in the generated header.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
To enable the Hyperflash you have to physically modify the board and
this disables the QSPI. Since we plan on removing Kconfig from device
trees, its easier to treat the hyperflash as a separate board config
and thus it will get a dts to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since Voltage Reference block is not supported, the ADC does not work
properly on FRDM-KW41Z. Set voltage reference to alternate source
in frdm_kw41z_defconfig.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
We had SEGGER support enabled by default previously, but the new
Kconfig option CONFIG_USE_SEGGER_RTT needs to be set as well now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The lpcxpresso54114_m0 tends to be the secondary core so doesn't
typically have a UART setup for it. We had SEGGER support enabled by
default previously, but the new Kconfig option CONFIG_USE_SEGGER_RTT
needs to be set as well now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board support for 96Boards STM32 Sensor Mezzanine board. This board
is one of the 96Boards Mezzanine board which can work standalone or on
top of the 96Boards Consumer Edition boards.
Below are some of the key features of this board:
1. STM32F446VE MCU
2. 96Boards high/low-speed connectivity
3. Arduino™ Uno revision 3 and Grove connectivity
4. Integrated MEMS sensors:
1. LSM6DS3H
2. LIS3MDL
3. LPS22HB
4. MP34DT01-M
5. On-board ST-LINK/V2-1 debugger/programmer
More information about this board can be found in the 96Boards product
page: https://www.96boards.org/documentation/mezzanine/stm32/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The 0.9.5 SDK has support for the Cypress PSoC6 family. Add ablilty to
flash with openocd. I've only tested flashing hello_world on the m0.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To enable the QSPI you have to physically modify the board and this
disables the hyperflash. Since we plan on removing Kconfig from device
trees, its easier to treat the QSPI flash as a seperate board config and
thus it will get a dts to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This driver introduces an emulated LCD display for the native POSIX
board. The emulated display driver makes use of SDL2 to render the
displays frame buffer into a dedicated desktop window.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Zephyr SDK 0.9.4 added OpenOCD support for SiLabs EFR32FG1P SoC. This
commit updates 'Flashing' paragraph of the board documentation to
reflect this change.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Fixes broken user guide and schematics links in nxp board documentation.
Updates remaining nxp.com links from http to https.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Connectors imaages for nucleo_f413zh were actually a reuse of
similar board nucleo_f412zg.
Add dedicated images for nucleo_f413zh.
Fixes#5198
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
'make flash' always erase the flash banks from sector 0, and flashing
the Zephyr.bin file to base address of flash even if there has a
bootloader placed on the first sector.
Users maybe want placed Zephyr to another location instead of sector
0 by adding 'zephyr,code-partition' in dts. But the openocd scripts
doesn't deal with that currently.
Fix this issue, flash zephyr.elf instead of zephyr.bin, elf file
contain load address and openocd scripts can deal with it.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Now that we can support the same compatible but different bus types,
update the LSM6DSL support to utilize the same compatible for either I2C
or SPI. We rename the i2c binding file to st,lsm6dsl-i2c.yaml just to
be a bit more clear.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
In commit d8e3ea6bc2
the LF clock interrupt was enabled, which causes its interrupt
handler to be used. This interrupt handler interacts with the
NRF_POWER registers.
Therefore require using the newer HW models which include a stub
of this registers.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
CONFIG_TEXT_SECTION_OFFSET allows the entire image to be moved
in memory to allow space for some type of header. The mcubootloader
can boot only such images which reserve some space for the header.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
This patch enables the UART_INTERRUPT_DRIVEN by default for
colibri_imx7d_m4, udoo_neo_full_m4 and warp7_m4 boards.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Reel Board doesn't enable BT by default like many of the nRF52
boards do. So let's make enabling BT a bit easier, by selecting
the BT_CTLR config when BT is enabled. This allows a sample
overlay to merely set:
CONFIG_BT=y
And the end result should be close to correct.
Signed-off-by: Michael Scott <mike@foundries.io>
The nRF51822 and nRF52832 does not support 802.15.4, so remove this
statement from documentation.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
Modify board stm32_min_dev aka "blue pill" led pin assignment in dts
from PB12 to PC13.
This board has a user led connected to PC13.
Sample blinky and similar would run out-of-box without additional
circuit to readout PB12 level.
Tested blinky on corresponding board.
Signed-off-by: Stephen Yi <stephen.jin.yee@gmail.com>
"-machine type=pc-0.14" appears to be the option which leads to
broken PCI emulation in QEMU, where PCI enumeration reports one
IRQ number (11), while actually IRQ 10 is emulated by QEMU.
"-vga none" and "-display none" appear to be just subordinate of
"-machine type=pc-0.14" and are required to get qemu_x86 into
bootable state.
Fixes: #11706
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
There are different interrupt numbers for R22 v R23. Before this was
being handled via using Kconfig symbol CONFIG_BOARD_EM_STARTERKIT_R23 in
emsk_dt.h. Since we want to remove use of Kconfig in dts we handle this
via different dtsi files and having the proper one included by the
proper board revision dts file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Towards removing Kconfig from DTS we need to move setting of the sizes
of ICCM/DCCM into the SoC specific DTS files and out of emsk_dt.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Including Bluetooth to every project unnecessary increase size of the
project, for example hello world sizes:
Memory region Used Size Region Size %age Used
FLASH: 48492 B 1 MB 4.62%
SRAM: 11236 B 256 KB 4.29%
IDT_LIST: 136 B 2 KB 6.64%
after the patch:
Memory region Used Size Region Size %age Used
FLASH: 13344 B 1 MB 1.27%
SRAM: 4004 B 256 KB 1.53%
IDT_LIST: 72 B 2 KB 3.52%
3+ times difference.
PS: It also crashes when 802.15.4 enabled.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add documentation for the quark_se_c1000_devboard with links to platform
guidelines and other details.
Fixes#11166
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Added description how to build, programm and see console output of
hello_world example on cy8ckit_062_wifi_bt_m0 board.
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
The EFM32 Pearl Gecko Starter Kit contains sensors and
peripherals demonstrating the usage of the EFM32PG MCU
family. This patch adds basic support for this board
and is copied from EFM32WG-STK3800.
Signed-off-by: Gil Benkö <gil.benkoe@pm.me>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Adds support for debugging and flashing the mimxrt1050_evk board via
pyocd. Support for this board has not yet been merged in upstream pyocd,
therefore the default in zephyr is left as jlink.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Merge up_squared_dts_fixup.h and up_squared_sbl_dts_fixup.h into
dts_fixup.h. This allows us to remove BOARD_DIR from being included
everywhere.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables Networking hardware on i.MX-RT 1050-EVKB board.
Pinout enabled board specific etherenet connection, also pin
initialization was moved later to PRE_KERNEL_2 in order to have
sysclock initialized before.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Fix link text to remove substitutions that are ignored by Sphinx. Also
replace link to Quark SOC HW ref manual to be from an Intel site (not
Russian).
Fixes: #11516
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Enabled Messaging Unit B in Cortex-M4 core of Udoo Neo Full board
so it can use IMX IPM.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Not pretty to change the PAD name from 2 to 1 as the correct
is PAD2 but for the SAMD20 the register value is 1.
Fixes: 6d08958ad5 ("drivers: uart_sam0: move sercom pad info to dts")
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Added support to the ti,cc2520 binding for optional GPIO signals and
moved the quark_se_c1000_devboard to define those signals in the DTS.
This lets us remove board.h and some #defines & fake Kconfig symbols
from the quark_se_c1000_devboard board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CC2520 device is specific to the quark_se_c1000_devboard not the
intel curie SoC. Move the device node where it belongs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that the in tree user of cc2520 uses device tree to configure SPI
and GPIO params, we can remove and convert the driver to utilize DT
only. This means removing the Kconfig options that come from DT and
rename CONFIG_ to DT_ for those options.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all SPI controllers support DTS we can remove the Kconfig
support for non-DTS options. We also cleanup some defines that should
have be DT_MCR20A_ instead of CONFIG_MCR20A_.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The majority of cases of CONFIG_I2C_x_IRQ_PRI should be
DT_I2C_x_IRQ_PRI. So go ahead and fix them up. Only the i2c_nios
driver still uses Kconfig for getting priority.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds a primitive board configuration for the UP Squared board to
work properly with SBL(Slim Bootloader).
- https://github.com/slimbootloader/slimbootloader
- https://slimbootloader.github.io/
BOARD shall be 'up_squared_sbl'
cmake -GNinja -DBOARD=up_squared_sbl ..
ninja
Signed-off-by: Aiden Park <aiden.park@intel.com>
Remove the ifdef related to CONFIG_FS_FLASH_STORAGE_PARTITION. There
shouldn't be any harm in always having the partition around as we'll
just generate the defines related to and most applications will ignore
them.
Helps get one step closer to have DTS not depend on Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The wncm14a2a modem is an add-on/shield and not part of the
nrf52840_pca10056 board and should be maintained and configured
outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The wncm14a2a modem is an add-on/shield and not part of the nrf52840_mdk
board and should be maintained and configured outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If we just had the kernel's implementation, we could
just move this to lib/, but possible arch-specific
implementations dictate that we just make this a
syscall.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Move to using Kconfig (like other Atmel SAM drivers do) to specify the
pinmux setting for SAMe70 SoCs. Updated the sam_e70_xplained board to
set the default in Kconfig.defconfig instead of via board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As explained in issue #8915 the STM32F4xx SoC family I2C
does not work well in Standard mode (100KHz). So let's
configure i2c3 in Fast mode (400KHz).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
We should let drivers or board code include soc.h directly so we can keep
board.h to local info for board specific code.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a TICKLESS_CAPABLE kconfig variable which is used by the kernel to
select tickless mode's default automatically on drivers that support
it (rather than having to set the default per-board). Select it from
the ARM SysTick and Intel HPET drivers.
Also remove the old qemu_cortex_m3 default settings which this
replaces.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Turning 'def_bool' in Kconfig.defconfig files into 'default' revealed
three unused symbols (confirmed with 'git grep'). Remove them.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
an explanation of how def_bool->default can reveal undefined symbols.
Removed unused symbols:
- SPI_DW_CLOCK_GATE
- PINMUX_MPS2
- BOARD_XTENSA
Also remove an assignment to the promptless symbol ALTERA_AVALON_SYSID,
in tests/boards/altera_max10/sysid/prj.conf. Assignments to promptless
symbols have no effect.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Previously we had a set of magic #define's in board.h that would both
enable and set the GPIO controller & pin if a given board used a GPIO
for USB VBUS. Now we make it a proper Kconfig set of options that
specify if the feature is needed, the GPIO controller device name, and
pin number. In the future this should move to devicetree.
Updated the related boards that used this feature to set the Kconfig
options in the Kconfig.defconfig
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added support for ST B-L072Z-LRWAN1 board configuration.
This board uses the same MCU as Dragino-LSN50.
Signed-off-by: Aleksandr Makarov <seems.deviant@gmail.com>
Removed pin 20 which by default is connected to QSPI memory.
Removed conflict with default pin assignment for UART 1.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
Convert the BMI160 to use Device Tree to get SPI and GPIO params instead
of Kconfig. Updated samples, tests, and arduino_101_sss board support
for this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Application should be responsible for enabling various drivers and
features, we should not enable everything by default.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update olimexino_stm32 configuration to match with default
configuration guidelines:
- Configure available UEXT connector which is available
on olimex boards.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Introduce new Kconfig option for selecting either slip or ethernet
connectivity to host.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In #10543 some include directives are modified to include some
folders in the path to the nrfx hal headers.
This would break things with the previous nRF52 HW models as the
replacement hal files were not placed in a folder matching that
path, and the include path was not pointing directly at the folder
containing the files.
Therefore, require the latest HW models version (which replicates
that folder structure), and add a new -I for the compiler 2 folders
higher.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This required wiring external daughter board by hand, it's not provided
by the board directly, let's remove this.
Applying the change on relevant samples.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Update stm32f469i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
-Update yaml file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32f723e_disco configuration to match with
default configuration guidelines:
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32f769i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32l496g_disco configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update disco_l475_iot1 configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This makes it possible to "ninja debug" to start debugging
towards the onboard debugger of the TB2 board.
Signed-off-by: Endre Karlson <endre.karslon@gmail.com>
The only difference between the F413xH and F413xG is flash memory size.
STMF413xH: 1536 Kbytes
STMF413xG: 1024 Kbytes
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
Remove either duplicate settings between arch & board, or just set
HAS_DTS at the arch level since all the boards for a given arch support
DTS now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This enables the USBHS interface on the Atmel SMART SAM E70 Xplained
Board, by adding an entry to the DTS. It also updates the documentation
and mark usb_device as supported for the tests.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Other ST boards have their openocd.cfg support file updated,
but Nucleo L476RG was still looking for board/st_nucleo_l476rg.cfg
and fails with Zephyr SDK 0.9.5.
Signed-off-by: Kiril Zyapkov <k.zyapkov@allterco.com>
Options "-clock dynticks" and "-balloon none" are deprecated and
produce warning in recent Qemu versions, so remove them.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Now that the samples use DT generated defines we can remove the
hexiwear_k64 specific ones in board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the Red, Green, & Blue PWM LED info to the device tree. We will use
this in the future for any samples that utilize PWM on these LEDs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
No need to check for BT being enabled. The UART entries will be
available for use if BT is enabled and will do nothing if not.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The wncm14a2a modem is an add-on/shield and not part of the frdm_k64f
board and should be maintained and configured outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This board can run in recent qemu versions (>3.0.0), so enable it
instead of a dedicated qemu board.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update the uart_miv driver to get params like name, addr, baud-rate,
clock freq from DTS generated defines. Fixup related board and soc code
as needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add minimal DTS support for the m2gl025_miv. The dts just has the core,
SoC, PLIC, and UART described. We still get memory related info from
Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adding watchdog driver for sam SoC. The current implemntation just
diables the watchdog on device boot.
This PR adds the following support for SAM3X, SAM4S and SAME70
1. Activate processor reset
2. Activate all reset
3. Generate interrupt on watchdog timer expiration.
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since the mb_display driver is specific to the microbit we can move
the GPIO pin defines from board.h into the driver. This lets us remove
one of the few remaining drivers that is including board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the GPIO info for the buttons into the dts, this lets us match what
all other boards are doing. Update some sample & test code to use the
dts generated SW0_GPIO_CONTROLLER define instead of SW0_GPIO_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added a check at compile time to ensure the HW models are either
the desired version or newer.
Otherwise print a warning.
The check can be disabled by setting the enviroment variable
NO_NRF52_BSIM_VERSION_WARNING.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Remove some references <board.h> that aren't need or replace them with
<soc.h> where that is the proper include to pull in. Also use "board.h"
instead of <board.h> for how we include the file when its local to the
board code itself.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The frdm_k64f and mimxrt1050_evk boards do not have native bluetooth
support, but rather require an arduino shield to supply a ble controller
over serial hci. Convert the dts to use the newly introduced frdm_kw41z
ble controller shield.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The frdm_kw41z can be used as a standalone board or as an arduino
shield. Zephyr already supports the standalone configuration, this
change introduces support the arduino shield configuration.
In the arduino configuration, the frdm_kw41z operates as a ble
controller over serial hci. It can be attached to another board, such as
the frdm_k64f or mimxrt1050_evk, which runs the ble host.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
native_posix is, from some reports, known to not compile
on macOS. Therefore let's better remove the line that says
that in principle it should to avoid missleading users.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The EFR32™ Mighty Gecko Starter Kit EFR32MG-SLTB004A (a.k.a
Thunderboard Sense 2) contains a MCU from the EFR32MG12P family built
on ARM® Cortex®-M4F processor with low power capabilities.
There is an On-Board J-Link Debugger that presents a virtual COM port
for general purpose application serial data transfer with this
interface and a Mass Storage for firmware flashing.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Combines the lpcxpresso54114_m4 and lpcxpresso54114_m0 boards into one
directory containing both board configurations. This eliminates some
duplicate code and documentation, and better represents the actual
hardware.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In an effort to reduce the number of CONFIG_ defines in dts files, we
can remove CONFIG_MCUMGR_SMP_UART and just always set
'zephyr,uart-mcumgr' as there is no harm to always having this set for
those board dts files that define the property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There were several issues in the dts binding for the ssd1673 display:
* binding file mixed description & generation up together
* Use of BASE_LABEL
* orientation-flipped should have been of type boolean
Update the binding file to reflect these changes, and made associated
changes to dts_fixup.h and driver as needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Flashing the board as described in the docs does not work without having
proper udev rules set. Add documentation for setting those.
Signed-off-by: Johannes Hutter <johannes@proglove.de>
Add a link to the reel board product page at PHYTEC to help people in
locating schematics, etc.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Added support for SPI 1 available from the arduino connector (plus an
extra gpio). Tested against samples/sensor/bme280.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
This is only a codestyle fix with no functional implications.
A few structures typedefs are removed. The structures are not in
use yet outside of the board code.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Fixed a typo in the warning message printed when the user does not
pass any parameters (and therefore does not connect to a BabbleSim
Phy)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The Adafruit Feather nRF52 does not have any RTS/CTS signal
connections between the nRF52832 and the on-board CP2104 USB/UART
bridge. Pins 5 and 7 are regular GPIOs.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Fixed a very unlikely NULL pointer dereference, which could occur
in an error condition, triggered if the test/fake HW timer model
was enabled but there was no registered handler for that timer tick.
The de-reference was in the error message printout.
Fixes#10778
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This enables I2C, SPI, PWM, RTC and USB.
RTC tested on samples/drivers/rtc
USB tested on samples/subsys/usb/cdc_acm
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
This adds the necessary bits to support ASM2 with XCC
for Intel S1000 SoC. With ASM2 enabled, xcc is now
required to build for Intel S1000 SoC.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Partially replaces Kinetis MCUX driver configuration from Kconfig to
Device Tree. Interrputs moved from defines configuration to DT.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Fix the following dts warnings:
up_squared.dts_compiled: Warning (simple_bus_reg): /soc/gpio@0:
simple-bus unit address format error, expected "d0c50000"
up_squared.dts_compiled: Warning (simple_bus_reg): /soc/i2c@91528000:
simple-bus unit address format error, expected "9158000"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for ST Micro Nucleo-64 board with the STM32F302R8
processor. nucleo_f429zi and nucleo_f334r8 were used as
references.
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Introduces the location property and adds the ability to use values
generated by the device tree configuration.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This feature was a useless noop based on mistaken API understanding.
The idea seems to have been that k_busy_wait() included guards to
ensure "clock_always_on" was true duing the loop, presumably because
the original author was afraid that "turning the clock off" would
affect the operation of k_cycle_get_32().
Then later someone came around and "optimized" this for Quark SE,
where the cycle counter is the RTC and unrelated to the timer driver
used by the clock_always_on feature. (Except even there it presumably
should have been done at the SoC level and not just in the C1000
devboard -- note that Arduino 101 never would have gotten this).
But it was all a mistake: "clock_always_on" has nothing to do with
en/disabling the system cycle timer (which never happens when the
system is active, that's a feature of idle), it's a control over the
delivery of timer interrupts. And needless to say we don't care about
timer interrupts when we're spinning on a cycle counter.
Yank the whole mess.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The config file sourced in openocd.cfg is the nuclean_f3 one instead of the one for
the stm32373c.
This makes it impossible to flash the stm32373c evaluation board rev.B:
Error: open failed
in procedure 'init'
in procedure 'ocd_bouncer'
error: command exited with status 1:
/opt/zephyr-sdk/sysroots/x86_64-pokysdk-linux/usr/bin/openocd -s
/opt/zephyr-sdk/sysroots/x86_64-pokysdk-linux/usr/share/openocd/scripts
-f
/home/maudat/repo_upstream/zephyr/boards/arm/stm32373c_eval/support/openocd.cfg
-c init -c targets -c 'reset halt' -c 'flash write_image erase
/home/maudat/repo_upstream/zephyr/samples/basic/blinky/build/zephyr/zephyr.bin
0x8000000' -c 'reset halt' -c 'verify_image
/home/maudat/repo_upstream/zephyr/samples/basic/blinky/build/zephyr/zephyr.bin
0x8000000' -c 'reset run' -c shutdown
Replace the file sourced by stm32f3discovery.cfg to flash successfully.
Signed-off-by: Mathieu Audat <mathieu.audat@savoirfairelinux.com>
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Add sample application for LSM303DLHC, ST MEMS
system-in-package featuring a 3D digital linear
acceleration sensor and a 3D digital magnetic
sensor.
Enable sample to build on stm32f3_disco board
during sanitycheck.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Enable LSM303DLHC, ST MEMS system-in-package featuring
a 3D digital linear acceleration sensor and a 3D digital
magnetic sensor, on stm32f3_disco board.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Sync peripheral mapping documentation with the Nucleo F429ZI board doc
and add missing information about Ethernet and the button.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
To ensure we can always go back in time, let's explicitly list the
NRF52 HW models version which should be used with each version of
the nrf52_bsim board
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Added a new simulated board, which models the NRF52832 SOC.
Its main use is for workstation testing and simulation of
the BLE stack and any application which relies mostly on it.
It uses BabbleSim (http://Babblesim.github.io) for the radio
simulation.
And the NRF52 HW models hosted in that same GitHub organization:
https://github.com/BabbleSim/ext_NRF52_hw_models
For speed it uses the POSIX arch to (not) emulate the CPU.
It uses Vanilla Zephyr, with a couple of configuration differences:
* It uses (like other POSIX arch boards) the system libC
* It does not use the nrfx hosted by Zehpyr in ext/, but the one
provided by the HW models.
Otherwise it relies in the same drivers as the real NRF52 boards.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This commit is taking care of following stuff:
1. pinmux: STM32F4 micro is using I2S5_CK and I2S_SD to interface with
on-board microphone.
2. default configuration:
- enable I2S5 and configure PLLI2S properly to generate
I2SxCLK = 128MHz.
- enable DMA
Note:
As stated in issue #9028 we needed to take care of a known SPI/I2S bug
implementing the following two actions:
A. APB2 clock has been slowed down to 42MHz.
B. The SPI/I2S clock gpio speed has been set to very_high_speed.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Previously, wifi-enabled samples were not built by sanitycheck for the
cc3220sf_launchxl.
This patch gets the sockets echo sample to build.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The USART fixup in the board dir really are SoC level fixup's. So move
them there and remove the board fixup file since there isn't anything in
it now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Contrary to what was written in its Kconfig, hal/altera depends not
on Newlib, but on a baseline POSIXish define like O_NONBLOCK. Minimal
libc now provides them, so there're no issues with building Altera
for either minimal on newlib libc.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The EFM32 Happy Gecko USB-enabled kit contains sensors and
peripherals demonstrating some of the EFM32HG MCU capabilities.
This patch add basic support for this board.
Signed-off-by: Marcio Montenegro <mtuxpe@gmail.com>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Convert over arc based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This will be usefull to tell when Ethernet device has its attributes
filled in by DTS rather than by Kconfig.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Convert over SiLabs based boards to use device tree instead of board.h
to describe buttons & LEDs. There are a few boards that the button
gpio flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert over x86 based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As per default board configuration guidelines, this commit updates
96Boards Nitrogen board.
Following changes are done:
- Enable I2C0 and SPI0 in board dts
- Add exposed peripherals in board Kconfig
- Update board yaml
- Remove config option to select board
- Update documentation for UART, I2C and SPI
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
As per default board configuration guidelines, this commit updates
96Boards Carbon board.
Following changes are done:
- Enable exposed I2C2 in dts
- Only enable basic peripherals in board defconfig
- Add exposed peripherals in board Kconfig
- Update documentation for SPI
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Convert over NRF based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The commit de78ecd "arm: beetle: Use device tree for IRQs" introduces
a regression related to UART1 IRQ.
On arm beetle the UART1 has IRQ number 2.
This patch restores the functionality modifying the arm beetle device
tree file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The Zephyr configuration system uses many different files in many
different formats. It makes it a lot easier for users to understand
what these files do if when we use the correct file extensions.
To this end we rename the dts.fixup files to the correct file
extension '.h'.
This is a breaking change for out-of-tree fixup files. Such files will
be detected and given an appropriate error message.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The dts.fixup for the hifive1 board was not board specific but related
to the SoC. Move the dts.fixup into the SoC dir so any other boards
using this same SoC will take advantage of it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move to getting the clock frequency of the uart from the device tree
instead of a define in the board file. Cleaned up hifive1 board code to
reflect this change in addition to the driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Some of the headers referenced in the pinmux.c file don't exist. Match
the includes that the lpcxpresso54114_m4 pinmux.c file uses.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the needed bits to get device tree support for the GPIO controller
on the Zedboard-Pulpino. This will allow us to move LED & button info
into the board.dts.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add simple device tree support for the Pulpino SoC and Zedboard-Pulpino
board port. This gets the UART info from device tree instead of soc.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add i2c/spi/gpio to the supported list to enable the CI to correctly
run the 96b_argonkey board sample.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch is equivalent to 7b0ce85242,
but applied to buttons. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The device name was missing for the lsm6dsl sensor in the 96b_argonkey
dts fixup, causing build warnings in tests/drivers/build_all.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
added sam4s16b, sam4s8c, sam4s8b, sam4s4c, sam4s4b,
sam4s4a, sam4s2c, sam4s2b and sam4s2a.
Used the same order as in the data sheet and code structure
equal to same70. Updated the sam4s_xplained board to match
the altered .dtsi location of the specific SoC.
Signed-off-by: Vincent van der Locht <vincent@vlotech.nl>
Remove the links to the now non-existant legacy shell documentation
and clarify a bit paragraphs (as the legacy shell is not default
anymore)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The peripherals sections grew by adding new peripherals
at the end. Reorder them so they follow a more reasonable
order.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Now, there is quite many more command line options for the
native_posix executable. But, which are available, depends
on the configuration. Therefore let's not list them in the doc,
but instead tell people to use the --help option.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This patch is equivalent to 7b0ce85242,
but applied to more boards. As stated in the previous commit message:
This change aims at fixing 'unit_address_vs_reg' warning in arm based
boards. This warning pops up when a node name is made up with an
address (node_name@xx) but does not contain a reg property. This case
was encountered for led nodes for instance, where a reg property has
no meaning. Fix this by changing node_name@xx to node_name_xx which
removes the guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_PINS and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled gpio drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_GPIO_DEVICE and
HAS_DTS_GPIO.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_DEVICE and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled i2c drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_I2C_DEVICE and
HAS_DTS_I2C.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Argonkey board building has been recently broken by a LSM6DSL sensor
driver fix (see commit: a013ce3bf0).
The board configuration file must now enable HAS_DTS_GPIO_DEVICE macro
instead of HAS_DTS_SPI_DEVICE.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
It is very inconvenient to maintain an application that both runs on a
Zephyr board and an out-of-tree board.
It forces one to write build scripts like this in the app:
if(BOARD STREQUAL my_out_of_tree_board)
set(BOARD_ROOT some/out/of/tree/board/path)
endif()
To avoid this we change the semantics of BOARD_ROOT. Instead of it
being a path to the board root it is now a prioritized list of board
root directories. Zephyr will append ZEPHYR_BASE to BOARD_ROOT.
This ensures that Zephyr boards can be used when the out-of-tree board
directory can not supply the requested board.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F7 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F3 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F2 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The spi drivers now consistently select HAS_DTS_SPI, so we no longer
need to select it at the board level.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Makes the designware spi driver consistent with other spi drivers by
selecting HAS_DTS_SPI in the driver. This required adding spi nodes and
dts fixups to several arc and x86 socs, as well as enabling those nodes
in associated boards.
Also refactors the driver to use the base address, interrupt number, and
interrupt priority from dts.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the L4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the L0 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F1 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added a new UART driver for posix arch boards.
The driver can be configured to either attach to a new
pseudo-terminal, or to connect to the invoking shell
stdin-out.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F0 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enable USB on nucleo_f249zi.
Update clock to allow precise USB clock.
Tested on samples/subsys/usb/cdc_acm
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enables instance 3 of the lpuart driver, adds dts fixups, and configures
pinmuxes to use bluetooth hci on the mimxrt1050_evk board. Updates board
documentation accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The i2c drivers now consistently select HAS_DTS_I2C, so we no longer
need to select it at the board level.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add board support files for mimxrt1060_evk, the development board for
i.MXRT1062 (CM7) SoC.
- Add pinmux, dts, doc.
- External QSPI flash hasn't been configured yet. So code can be loaded
to SRAM for now.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
The i2c_slave_api test was not getting executed on the nucleo_f091rc
board due to a missing supported features list.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Cleanup unused leftover from shield development.
These flags are not actually useful, nor used as dts connectors
are sufficient to control board to shield binding is
operational and dtc provides meaningful error message
when this is not the case.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This change aims at fixing 'unit_address_vs_reg' warning in
STM32 based boards.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for led nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@xx' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The nrf52840_pca10056 defconfig apparently started off as a copy of the
one for nrf52840_pca10040 and one comment was forgotten to be adapted
accordingly.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
This patch adds support of the SAMD21 XPlained board. The board has a
similar pinout to the SAMD20 XPlained with a different pin-mapping.
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
In dts.cmake, build shield list. For each shield, check if
associate KCONFIG is enabled and if it is, add matching files
to following new cmake variables:
-DTC_SHIELD_OVERLAY_FILE
-DTC_SHIELD_FIXUP
Then, consume these variables when needed.
Shield overlay is conceived as the very first overlay applied
to the board dts. It intends to build a new board that should
then behave as any other board versus common or user's overlay.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added cy8ckit_062_wifi_bt_m4 board configuration to build FW for CM4
core.
CM4 core does not start itself, it have to be started by CM0+ FW.
Signed-off-by: Nazar Chornenkyy <nazar.chornenkyy@cypress.com>
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
This patch changes the behavior of the sensor. The sensor
will remain in sleep mode after initialization and will only
run the measurements once when sample_fetch is called.
This optimizes the power consumption of the sensor as it
stays in sleep mode most of the time.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This change aims at fixing 'unit_address_vs_reg' warning in
STM32 based boards.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for button nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@XX' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable UART 16550 driver for Nios-II QEMU platform.
Note: This PR is tested with patched version Qemu 3.0.0 which
adds support for altera_10m50_zephyr machine type.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
This commit removes all MPU-related (ARM_CORE_MPU and NXP_MPU)
options exept ARM_MPU, which becomes master switch controlling
MPU support on ARM.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The HAS_SYSMPU option is just selecting NXP_MPU option,
which could be also controlled through menuconfig.
This commit removes the HAS_SYSMPU option and replaces
its usage by NXP_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The ARM_MPU_IMX_RT option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the ARM_MPU_IMX_RT option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The ARM_MPU_NRF52X option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the ARM_MPU_NRF52X option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The ARM_MPU_ENABLE option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the ARM_MPU_ENABLE option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The STM32_ARM_MPU_ENABLE option is just selecting ARM_MPU option,
which could be also controlled through menuconfig.
This commit removes the STM32_ARM_MPU_ENABLE option and replaces
its usage by ARM_MPU option.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Sets the HPET timer frequency (enabled by default) to 19.2MHz.
And also sets the local APIC timer frequencies according to
the SoC variant.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are currently three SoC variants for the UP Squared board:
Pentium, Celeron and Atom. This adds a board option to specify
for which variant is being built.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Enables an instance of the lpspi peripheral, configures the pinmuxes,
and updates the board documentation accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
We get the following warning when building nrf52810_pca10040:
Warning (avoid_unnecessary_addr_size): unnecessary
#address-cells/#size-cells without "ranges" or child
"reg" property in /buttons
Remove #address-cells/#size-cells since they aren't needed for gpio_keys
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When we fixed the missing reg property in the cpu node, we forgot to
add #address-cells & #size-cells for the node.
This fix the following warnings we get:
Warning (reg_format): "reg" property in /cpus/cpu@0 has invalid
length (4 bytes) (#address-cells == 2, #size-cells == 1)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get the following warning when building nrf52810_pca10040:
Warning (avoid_unnecessary_addr_size): unnecessary
#address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys
Remove #address-cells/#size-cells since they aren't needed for gpio_keys
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /flash: node has a reg or ranges
property, but no unit name
or
Warning (unit_address_vs_reg): /memory: node has a reg or ranges
property, but no unit name
Fix by adding unit address that is missing to flash & memory nodes.
Additionally the Silabs memory nodes didn't have a compatiable or
device_type, so add those properties as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /cpus/cpu@0: node has a
unit name, but no reg property
Fix by adding reg property to missing cpu nodes.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /cpus/arcv2-intc@0:
node has a unit name, but no reg property
Fix by removing the unit address from the nodes. Some cases we had a
reg property and a unit address for such interrupt controllers, in those
cases remove both the reg & unit address in the node name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /gpio_keys/joystick@0:
node has a unit name, but no reg property
Fix by dropping the unit address and renaming the node names to include
more information about the gpio_key.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (alias_paths): /aliases: aliases property name
must include only lowercase and '-'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enable native logger backend for native_posix board in defconfig.
Set also logger configuration options suitable for native_posix
backend.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
For native_posix:
Added command line options to control if traces should have
or not colors.
+
Detect if we are connected to a tty or not, and if we are
set the defaults for that option appropriately
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Update all supported features and peripherals in the official set of
boards from Nordic Semiconductor.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_NRF51822_QFAA
CONFIG_SOC_NRF51822_QFAB
CONFIG_SOC_NRF51822_QFAC
CONFIG_SOC_NRF52810_QFAA
CONFIG_SOC_NRF52832_QFAA
CONFIG_SOC_NRF52832_CIAA
CONFIG_SOC_NRF52832_QFAB
CONFIG_SOC_NRF52840_QIAA
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_PART_NUMBER_SAME70*
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have a common DT_SIZE_K macro use it instead of defining
__SIZE_K eveywhere. We also have DT_SIZE_M, so use that in a few
places as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_PART_NUMBER_EFM32WG990F256
CONFIG_SOC_PART_NUMBER_EFR32FG1P133F256GM48
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_CC3220SF
CONFIG_SOC_MSP432P401R
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
UART pins (TX, RX, RTS, CTS) are now configured in DTS files.
RTS and CTS definitions are optional. If flow control is enabled
and RTS/CTS pins are not defined, then compiler will issue
an error message.
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
With the new Kconfig preprocessor (described in
https://github.com/torvalds/linux/blob/master/Documentation/kbuild/
kconfig-macro-language.txt), the syntax for expanding environment
variables is $(FOO) rather than $FOO.
$(FOO) is a general preprocessor variable expansion, which falls back to
environment variables if the variable isn't set (like in Make). It can
also be used in prompts, 'comment's, etc.
The old syntax will probably be supported forever in Kconfiglib for
backwards compatibility, but might as well make it consistent now that
people might start using the preprocessor more.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The prefixes might be a leftover from the old 'option env="..."' symbols
(which are no longer needed). Since environment variables can be
referenced directly now, there's no point in having a prefix.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The LEDs, buttons and necessary aliases are now configured via dts.
This commit breaks the samples under boards/nrf52/mesh:
- onoff-app
- onoff_level_lighting_vnd_app
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The LEDs, buttons and necessary aliases are now configured via dts.
This commit breaks the sample under samples/boards/nrf52/power_mgr.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
This patch adds USB capabilities to the stm32f4 discovery board.
As the board has a MicroUSB port that I would like to use as stdout I
just added USB. The needed entry within pinmux.c is already there but
USB was missing in the dts file and documentation.
I tested it with the upcomming commit.
Signed-off-by: Alexander Polleti <metapsycholo@gmail.com>
This change adds DTS definition of SPI device for nRF chips.
It also removes SPI pin configuration from Kconfig and moves it to
chip DTS.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
When I2C and SPI are not used (such as when building a simple
bootloader for this target), the current Kconfig is generating a fair
bit of warning spew. Clean it up by moving some explicit _defconfig
settings into defaults.
Signed-off-by: Marti Bolivar <marti@foundries.io>
This reverts commit b0d3b560238fac09e63064620de9ff820cf8cc47.
Since we now have a working ADC driver for Quark D2000,
re-add the tag.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The stub is used for testing only and is not compatible anymore with the
usage documented here.
Fixed#9772
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The version of OpenOCD provided by Zephyr SDK is too old and does not
contain support for EFR32FG1P chip. This patch assumes that user
compiles and installs the newest version of OpenOCD.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This config is only valid for kinetis boards. Fixes the Kconfig warning:
warning: the choice symbol OSC_EXTERNAL (defined at
arch/arm/soc/nxp_kinetis/Kconfig:53) was selected (set =y), but no
symbol ended up as the choice selection.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The LPCXpresso54114 command line example was using a wrong board
name which has been renamed after adding the support for the
Cortex-M0+ core.
Fixes#9649
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
This adds to the adc_api test board-specific configurations
for the following boards:
- nrf51_pca10028
- nrf52_pca10040
- nrf52840_pca10056
"adc" is indicated as supported in the yaml files for these boards
so that they are included in sanitycheck.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
ADC nodes are enabled in DTS for the following nRF development kits:
- nrf51_pca10028
- nrf52_pca10040
- nrf52_pca20020
- nrf52810_pca10040
- nrf52840_pca10056
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use Kconfig specific object "named choices".
Aim is to allow to define config choices selection in Kconfig.*
files instead of _defconfig and hence allow to keep flags
activation conditional.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename GPIO_INT_CONF to GPIO_FLAGS in order to be able to use
the definition generated by the devicetree, eliminating the need
for definition in the board.h file
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
set DISK_FLASH_MAX_RW_SIZE to 256, as maximum bytes that can be
programed to SPI FLASH by Page Program Command is 256.
Fixes#8506
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Now that the corresponding flash definitions have been added to the DTS,
it's possible to enable the nvs sample in the NUCLEO-L432KC board.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch adds DT description of generic storage flash partition using
the last 16kB of flash when CONFIG_FS_FLASH_STORAGE_PARTITION is
defined. This can be used for FCB or NVS filesystems.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use the correct pyOCD target type for the NRF52840.
This fixes b92436a13f.
Tested with: Atmel ICE Debugger
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Removes the platform whitelist, leaving just the depends_on/supported
pattern to select which platforms the sample can run on.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add support for using non-jlink programmers through pyOCD.
Tested with: Atmel ICE Debugger
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add support for using non-jlink programmers through pyOCD.
Tested with: Atmel ICE Debugger
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This patch is to add support for the WaRP7 board which has an i.MX7
Solo SoC.
The Zephyr is running on the Cortex M4 core and the following features
were validated on this board:
* GPIO: User Switch detection and sensors interrupt
* UART: Zephyr console
* I2C: Communication with fxos8700 and fxas21002 sensors
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Move to more generic tracing hooks that can be implemented in different
ways and do not interfere with the kernel.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fix in command line parsing common functions, to prevent
a possible segfault when handling string type arguments
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Added an entry in drivers/Kconfig for audio
Added an entry in drivers/audio/Kconfig for audio codec
Added an Kconfig file in drivers/audio/ for TLV320DAC
Enabled audio coded in Intel S1000 CRB defconfig
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
PR #8729 removed the old GPIO_NRF5 driver in favor of an
nrfx-based one. The reel_board still references the old one,
causing CI failures.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As reported in issue #9494, BT samples are using the off-chip
UART-based BT controller on 52810. But the on-chip BT controller is
supported on 52810, so this is the reasonable default when BT is
enabled.
This patch enables BT_CTLR by default when BT is enabled.
This resolves#9494.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
I removed GPIO configuration from board files and enabled them
as default in driver Kconfig file. All boards had GPIO ports
enabled that is why I decided to enable it by default.
Power management example was changed to use new driver.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
FE310 is the name of one SoC out of a range of products in the SiFive
Freedom line. The FE310 SoC port in Zephyr is compatible with all of
these products, so rename the SoC to SiFive Freedom
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
This patch adds support for Ethernet in the STM32F2 family of
microcontrollers and enables it for the the Nucleo-F207ZG.
Signed-off-by: Daniel Egger <daniel@eggers-club.de>
A design flaw of 'gsource' is that there's no way to require at least
one file to match the glob pattern. This could lead to silent errors.
Switch to a new design, where a plain 'source' is globbing and requires
at least one file to match. A separate 'osource' (optional source)
statement is available for cases where it's okay for a pattern (or plain
filename) to not match any files.
'orsource' combines 'osource' and 'rsource' (relative source).
This commit search-replaces 'gsource' with 'source', but backwards
compatibility with 'gsource' is still maintained by making it an alias
for 'osource' (and by making 'grsource' an alias for 'orsource').
The three Kconfig files arch/{nios2,posix,xtensa}/Kconfig source
arch/{nios2,posix,xtensa}/soc/*/Kconfig, which doesn't match any files.
Use 'osource' for those. The soc/*/Kconfig files seem to be for
additional SoC-specific symbols, only none exist yet on those ARCHes.
Also use 'osource' for the source of $ENV_VAR_BOARD_DIR/Kconfig in
boards/Kconfig, which doesn't exist for all boards.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The old GCC ARM Embedded website on launchpad
(https://launchpad.net/gcc-arm-embedded) has been superseeded by the new
GNU Arm Embedded one
(https://developer.arm.com/open-source/gnu-toolchain/gnu-rm).
This also means a change of name from "GCC" to "GNU". Reflect this in
the enviroment variables so that the proper term is used henceforth.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
A bug in the jlink application made it impossible to use OpenSDA
firmware with the mimxrt1052 device name, so we used the generic
Cortex-M7 device name as a workaround. This bug was fixed in jlink
V6.32h (2018-07-05), so now we can use the more specific device name.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
These settings enable use of the WNC-M14A2A LTE-M modem as the default
network interface for the nRF52840-DK board (nrf52840_pca10056).
They include the following settings when MODEM_WNCM14A2A is selected:
- UARTE1 pin setup
- DTS / DTS fixup additions for WNC-M14A2A
- Kconfig settings for modem driver
Signed-off-by: Michael Scott <mike@foundries.io>
These settings enable use of the WNC-M14A2A LTE-M modem as the default
network interface instead of ethernet.
They include the following settings when MODEM_WNCM14A2A is selected:
- UART 2 setup
- Avoid ETH_0 setup due to pin conflicts
- DTS addition for WNC-M14A2A
- Kconfig settings for modem driver
Signed-off-by: Michael Scott <mike@foundries.io>
A few function prototypes were missing in the native_posix
board and its drivers.
Let's add them.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
For each driver/model with command line options.
Move its code for the board file into the driver/model file.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Allow command line arguments to be registered dynamically
instead of being statically defined.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Some drivers or tests need to execute some code before Zephyr is
booted, dynamically register command line arguments, etc.
For this purpose, we generalize the NATIVE_EXIT_TASK to also
provide hooks to run a function at a given point during the startup
of native_posix.
Also, test/boards/native_posix/exit_tasks is generalized to cover
this new functionality.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The board config has been verified to boot with serial console
on the Atom version of the UP Squared board. So the references
to Pentium/Celeron can be removed. Moreover, add some notes on
BIOS settings, as it may change the MMIO addresses for various
IP blocks.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add the necessary bits to enable the I2C controllers on
the UP Squared board. Only the ones exposed through the HAT
connector(s) are enabled by default.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This enables the cc3220sf_launchxl to automatically
reconnect to the last good known access point (AP).
This method avoids the need to:
- perform a wifi scan for access points on bootup (saving power);
- include hard-coded SSID/passwords in the wifi application.
- include the wifi shell in the wifi application.
- rely on more complex provisioning methods;
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Enable the support for the 3 I2C buses of the STM32F723E-DISCO board,
connected respectively to the WM8994, the Arduino V3/STMOD+ and the
touch panel.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For native_posix:
Added the option to control the speed of the simualated time vs
the real(host) time.
Added a model of a real time clock with an API.
In the documentation we clarify the relationship between simulated
time and real time, and include documentaion of this new RTC.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Until now, command line options switches which matched the
begining of other options with argumentes needed to be listed
after those. After this fix this is not neccessary anymore.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Let the HW events which would have executed right at the
stop-at time happen, as this produces a more intuitive runtime.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Due to bug #9054 this boards is being disable from sanitycheck
temporarily.
Revert when the board is fixed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit adds support for the nrf52840_pca10059 board.
The flash partitions are configured to allow migrating from
the stock bootloader to MCUBoot.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Mark this board as simulation board to be run with nsimdrv.
See documentation for how to get nsimdrv.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some of the native application components or drivers need to
do a proper cleanup before the executable exits.
So we provide a macro similar to SYS_INIT but which will be
called just before exiting.
This can be used for freeing up resources, closing descriptors,
or doing any neccessary signaling to any other host process.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This adds a primitive board configuration for the UP Squared board
containing Apollo Lake based Pentinum and Celeron SoC. This has
been tested on model UPS-APLP4-A10-0432.
This starts from the minnowboard configuration, and document
from galileo.
Origin: Original
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This extends the build_grub.sh script so that it can build 64-bit
Grub UEFI application, and thus enabling us to boot on systems
with 64-bit BIOS.
Also updated the script to checkout the tag grub-2.02 since
v2.02 has been out.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
After running some tests which enable assert macro I found some issues
with the i.MX UART configuration.
This patch configures the Tx Fifo Watermark and Modem Mode accordingly.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Addition of a Flash partition to the 'frdm_k64f.dts' file in the
currently existing 'Application Area' (Partition Location: 0x0001e000
Partition Size:0x00002000). This partitioned area can be used as a FCB
for Bluetooth and other applications.
Signed-off-by: Arjun Warty <arjun.warty@nxp.com>
This commit enables the use of UARTE on Nordic nrf52810_pca10040
development kit. It also instruct console to use UARTE (instead
of RTT).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The Adafruit Feather nRF52 is based on an Nordic Semidconductor nRF52832
based development board with UART, SPI, LED and onboard lithium polymer
battery charger.
Signed-off-by: Florian Gärtner <florian.gaertner@ledcity.ch>
two configs are contained in this board
* nsim_em: em with arc MPUv2
* nsim_sem: em with arc SecureShield and MPUv3
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The EFR32 Flex Gecko Wireless Starter Kit contains sensors and
peripherals demonstarting the usage of the EFR32FG1P SoC
family. This patch add basic support for this board.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
The PHYS_LOAD_ADDR Kconfig symbol was removed by commit b8ea7c889d
("x86: remove HAS_DTS checking"). The ROM_SIZE Kconfig symbol was
removed by commit e524f0b846 ("dts: x86: derive RAM and ROM size from
dts instead of Kconfig").
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add first set of boards which can be built with xtools, this will
include all boards at some point, so we might need a better way to
whitelist toolchains that does not include changing every single board
definition file. For now enabling those needed for testing the new
toolchain.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Latest crosstools NG supports ARC, so add it here for those who build
their own toolchains using xtools-ng or use the scripts from sdk-ng repo
in the zephyr project.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch adds basic support and for the STM32F769I-DISCO board
with GPIO, USART support. Two USARTs are enabled.The GPIOs are
configured for the 4 LEDs and one button on the board.
Signed-off-by: Yong Jin <jinyong.iot@foxmail.com>
Override the C standard used for compilation to C 2011
This is due to some tests using _Static_assert which is a 2011
feature, but otherwise relying on compilers supporting it also
when set to C99.
This was in general ok, but with some host compilers and C
library versions it led to problems. So we override it to 2011
for native_posix board.
Fixes: #8529
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Set HAS_ARDUINO_XXX flag to state boards is compatible with this
connector. It will enable use of shields that requires these flags.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to provide a way to control boards/shields compatibility,
provide connector flags.
One should select this flag in Kconfig.board to state connector
compatibility for the board.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Have qemu_cortex_m3 use the traditional multiqueue scheduler by
default, to be sure it gets test coverage.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Make these "choice" items instead of a single boolean that implies the
element unset.
Also renames WAITQ_FAST to WAITQ_SCALABLE, as the rbtree is really
only "fast" for large queue sizes (it's constant factor overhead is
bigger than a list's!)
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This patch adds basic support and documentation for the STM32F723E-DISCO
board, with GPIO, USART, I2C and USB support. Two USARTs are enabled,
the VCP one for the console and the Arduino one. The GPIOs are
configured for the 3 LEDs and the button available on the board.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Unconditional CONFIG_BT_SPI_BLUENRG flag activation was generating
a systematic warning.
Move it in Kconfig.defconfig file to avoid the warning
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The ArgonKey board has 12 leds controlled by TI LP3943 led
controller. Add the support in the BSP.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Now that it is possible to easily add Kconfig options from command
line, we do not need to always compile native_posix with coverage.
This was done only to have it set easily for sanity_check.
So do not select it anymore, and let users choose if they
want coverage dumps or not.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Since the PCA10040 contains the required DC/DC circuitry, enable it by
default while keeping it configurable. This reduces power consumption
during radio activity.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the PCA10040 contains the required DC/DC circuitry, enable it by
default while keeping it configurable. This reduces power consumption
during radio activity.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Adding new implementation of logging subsystem. New features
includes: support for multiple backends, improving performance
by deferring log processing to the known context, adding
timestamps and logs filtering options (compile time, runtime,
module level, instance level). Console backend added as the
example backend.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
The patch contains basic code support, documentation, dts
file and openocd configuration for STM32F746G discovery board.
This patch related to the issue #6982.
Signed-off-by: Yurii Hamann <yurii@hamann.site>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that for any of the removed properties though.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Segger provide a firmware makes the ST-LINK on-board compatible with
J-Link OB, allowing users to take advantage of most J-Link features
such as RTT(Real Time Transfer).
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
The nRF52810 is a low-cost variant of the nRF52832, with a reduced set
of peripherals and memory. This commit adds Bluetooth controller support
for it.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit selects HAS_DTS_I2C in bbc_microbit board definition.
It fixes issues similar to issue #8511 for bbc_microbit board
Signed-off-by: Mandar Chandrakant Thorat <mandar.chandrakant.thorat@intel.com>
The commit modifies the I2C-related defines in nrfx
configuration to comply with the updates in (57e3644).
It also modifies the i2c configuration in DTS for board
nrf52810_pca10040 to reflect the nRF52810 capabilities.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit moves the definitions for the LED and Buttons
supported in nrf52810_pca10040 DK in DTS from board.h. Aliases
are kept in board.h to make basic examples pass.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds a compile-time directive for the
nrf52810_pca10040 board that instruct nRFx to perform
certain board initialization. The directive is needed
as nrf52810_pca10040 mirrors the nrf52832 DK hardware.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The nRF52810 is a low-cost variant of the nRF52832, with a reduced set
of peripherals and memory. This commit adds basic support for it in the
arch SoC and dts folders.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Ioannis Glaropoulos <ioannis.glaropoulos@nordicsemi.no>
Since Nordic does not offer an nRF52810 Development Kit and instead
recommends using the nRF52 DK (nRF52832 based), add a board that
enforces the limitations of the nRF52810 but is designed to be flashed
onto the actual nRF52 DK hardware.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Ioannis Glaropoulos <ioannisg.glaropoulos@nordicsemi.no>
In order to avoid auto-selection by Kconfig, the board needs to define
the specific IC that it contains, in this case an nRF52832.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update the link to SAM3X8E datasheet and
update the minicom command to use sudo as
accessing the serial port requires root permission
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
native_posix relies on the host C library even if users think
they are selecting one of the lib/libc C libraries.
For the math functions to be available at link time we need
to link to the host math library when building for this board
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Fixes#8391
Enables the i2c drivers for these boards.
Required to enable i2c with these boards.
Tested samples/sensor/tmp112 for nrf52_blenano2
with i2c enabled.
Signed-off-by: Mandar Chandrakant Thorat <mandar.chandrakant.thorat@intel.com>
This commit adds support for Microsemi Mi-V RISC-V softcore CPU
running on the M2GL025 IGLOO2 FPGA development board.
signed-off-by: Karol Gugala <kgugala@antmicro.com>
This commit moves code from fe310 platform into RISC-V privilege common
folder. This way the code can be reused by other platforms in future.
signed-off-by: Karol Gugala <kgugala@antmicro.com>
Currently tests/benchmark/footprint build is failing for
nrf52_pca20020 board. In minimal configuration, all modules are
disabled, including GPIO, because of that defines related to GPIO
are missing in board.c file and compilation fails.
To solve it, I selected GPIO to be always turned on for
nrf52_pca20020 board.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
SDA and SCL pins can now be configured through DTS.
Pins on development kits have been assigned according to arduino
headers.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
The UDOO Neo Full single board computer configuration supports
the following hardware features on the Cortex M4 Core:
+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component |
+===========+============+=====================================+
| NVIC | on-chip | nested vector interrupt controller |
+-----------+------------+-------------------------------------+
| SYSTICK | on-chip | systick |
+-----------+------------+-------------------------------------+
| UART | on-chip | serial port-polling; |
| | | serial port-interrupt |
+-----------+------------+-------------------------------------+
| GPIO | on-chip | general purpose input/output |
+-----------+------------+-------------------------------------+
The default configuration can be found in the defconfig file:
boards/arm/udoo_neo_full_m4/udoo_neo_full_m4_defconfig
Other hardware features are not currently supported by the port.
Connections and IOs:
The UDOO Neo Full board was tested with the following pinmux
controller configuration.
+---------------+-----------------+---------------------------+
| Board Name | SoC Name | Usage |
+===============+=================+===========================+
| J4 RX | UART5_RX_DATA | UART Console |
+---------------+-----------------+---------------------------+
| J4 TX | UART5_TX_DATA | UART Console |
+---------------+-----------------+---------------------------+
The board has been tested with the following samples.
- samples/hello_world
- samples/basic/blinky
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Both variables were used (with the same value) interchangeably
throughout CMake files and per the discussion in GH issue,
ZEPHYR_BASE is preferred.
Also add a comment with explanation of one vs. the other.
Tested by building hello_world for several boards ensuring no errors.
Fixes#7173.
Signed-off-by: Alex Tereschenko <alext.mkrs@gmail.com>
This commit enables CAN on the STM32L432.
Tested on nucleo l432ck with external transceiver and loopback mode.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
CONFIG_SPI_FLASH_W25QXXDV_MAX_DATA_LEN is a left-over from old SPI API
usage. Now, there is no limit (besides the flash size) in SPI data
transaction.
Fixes#8327
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This adds basic support for declaring gpio nodes in dts for nrf52.
The dts.fixup provides mapping for the generated defines to the config
defines currently used by the nrf gpio driver.
Existing boards that use nrf52 are updated.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
These symbols were removed by commit ed26b95 ("drivers/gpio:
Removing dts generated options in QMSI Kconfig"). The settings should
come from DTS now.
Commit 9611002f7a ("boards/x86: Use right GPIO names for CC2520")
fixed some of the references, but there are still others left. Guess
that the same fix is appropriate in those spots (hardcoded
"GPIO_0"/"GPIO_1" names).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Added a hidden Kconfig option in arch/arm/soc/nordic_nrf
which is selected by selecting DC/DC circuitry being present
in the board.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixed the BT_USERCHAN config warning
by setting it only if BT_HCI is selected,
instead of setting it always and relying on it
being set to "no" by not meeting that dependency.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Fixed the FAKE_ENTROPY_NATIVE_POSIX config warning
by setting it only if the entropy generator is used,
instead of setting it always and relying on it
being set to "no" by not meeting that dependency.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
UART driver renamed to keep the same convention as SPI and TWI drivers.
All substrings: "UART_NRF5" in defines renamed to "UART_NRFX_UART".
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
As the nRF52840 supports 802.15.4 natively, we should default y
for IEEE802154_NRF5 if IEEE802154 is enabled.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
commit 53a924b390
clobbered parts of
commit 9d2f370ddb
which included changes to make cc3220sf_launchxl XIP by default.
This patch reverses the clobber.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
For the native_posix board,
added the command line options -rt and -no-rt to control
if the execution should be slowed down to real time or not.
CONFIG_NATIVE_POSIX_SLOWDOWN_TO_REAL_TIME still works, but
now it just sets a default.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Fix in interrupt wrapping for native_posix so it also
supports meta-interrupts.
Related to commit:
3a0cb2d35d
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
New tests rely on irq_offload() actually being based on an
interrupt.
So let's base it on a new SW interrupt.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Introduce a custom HCI driver for the native POSIX port, which opens a
HCI User Channel socket to the Linux kernel to gain access to a local
Bluetooth controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is a core platform that needs to be tested by default. Fix the
default tag in the board YAML (it was duplicated in the wrong section).
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
GPIO_QMSI_<0/1>_NAME are now generated through DTS. Until CC2520
settings are generated through DTS, let's use direct gpio names
instead.
Fixes#8086
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The flash script was broken after the cmake changes.
Updated the path needed for the flash scripts.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
The file boards/common/intel_s1000_crb.board.cmake is not common at
all; it is specific to this board. Move its contents into the board's
board.cmake.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Fix the runner invocation for intel_s1000 board by getting
rid of board-dir, gdb and kernel-elf parameters.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
The choice symbol LSM6DSL_EXT0_LIS2MDL was given a 'default' in
Kboards/arm/96b_argonkey/Kconfig.defconfig, but 'default' has no effect
on choice symbols, triggering a warning from Kconfiglib.
Instead of adding a default to the choice symbol, change the default of
the 'choice' itself by giving it name and adding the default in
Kconfig.defconfig.
This requires that we remove the default on the "base" definition of the
'choice', due to some messiness related to the Zephyr-specific
prefer-later-defaults behavior (see the 'Zephyr-specific Kconfig
behavior for defaults' section in the Board Porting Guide). Choices were
overlooked when that patch was added to the C tools, meaning choices
still prefer earlier defaults. The crux is that Kconfig.defconfig files
are included last.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
These symbols were removed in commit 311e6b9e3e ("arch: arc: Use DTS
for all ARC SoCs"). The settings should come from DTS now.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fixed the incorrect usage of CONFIG_FLASH in the defconfig.
This CONFIG_FLASH is used to enable the flash driver only.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Fixed the incorrect usage of CONFIG_FLASH in the defconfig.
This CONFIG_FLASH is used to enable the flash driver only.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Fixed the incorrect usage of CONFIG_FLASH in the defconfig.
This CONFIG_FLASH is used to enable the flash driver only.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
In preparation for introducing a warning.
Unquoted string defaults work through a quirk of Kconfig (undefined
symbols get their name as their string value), but look confusing. It's
done inconsistently now too.
Suggested by Kumar Gala.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The ST Nucleo L432KC board only has a reset switch and not user switch.
It has a single user LED connected to PB3, and called LD3 in the ST
documentation.
This patch fixes the corresponding device tree definition. At the same
time also it also fixes the documentation, where the name of the power
and user LEDs are swapped.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
TI literature site has links which are automatically updated to point
to the latest versions of pdf documents.
Use those instead of the hardcoded URLs.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Update board docs to reflect simpler method of flash/debug as
cc3220sf is now by default an XIP platform.
Include installation instructions for TI OpenOCD as a pre-requisite.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Previously, the cc3220sf platform could only be flashed using
TI UniFlash (or CCS) tools, requiring unique instructions.
Also, these procedures were not integrated with the standard Zephyr
build targets: 'flash', 'debug', 'debugserver'.
After installation of a TI OpenOCD v1.10 release, and other
one-time board setup, flashing and debugging can now be done
via OpenOCD/gdb, using the standard Zephyr build targets per
the Zephyr Application Development primer.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Previously, there was no easy command-line solution for loading
a Zephyr program to (internal) flash.
So, the default development method was to load via gdb/openocd
to SRAM and debug from there, thus making the cc3220sf platform
non-XIP (CONFIG_XIP=n) by default.
With new openocd v 1.10 updates from TI (git.ti.com/sdo-emu),
the image can now be flashed and debugged via gdb/openocd,
so the default will be changed to XIP (CONFIG_XIP=y).
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
As mentioned in
https://github.com/zephyrproject-rtos/zephyr/issues/7873, these Kconfig
symbols never existed. Remove the assignments to them.
Keep the dead code that's guarded by them for a while. I don't know if
this board is used.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Supposed to come from DTS. The Kconfig symbol was removed in commit
311e6b9e3e ("arch: arc: Use DTS for all ARC SoCs").
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
According to INTEL-SA-00115[1], Intel(r) Atom(tm) Processor E Series
are affected. All Minnowboards sports one of these processors.
[1]: https://goo.gl/CKyLQy
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Setting of CONFIG_HEAP_MEM_POOL_SIZE was done in the board defconfig
because open-amp was doing recursive builds and setting it the
defconfig made sure all builds were consistent. However, now that we
don't do recursive builds this will get properly picked by from the
sample specific conf file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The {FLASH,SRAM}_BASE_ADDRESS Kconfig symbols were removed in commit
311e6b9e3e ("arch: arc: Use DTS for all ARC SoCs"). These settings are
supposed to come from DTS now.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
USB IP is not directly available on disco_l475_iot1 and requires
some HW modifications to get it enabled.
Remove this USB pinmux configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
During transition from native to ll based clock_control
driver, a typo was introduced in PPL source selection flag.
Fix this.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The defconfig has CONFIG_SOC_MKL25Z=y, however CONFIG_SOC_MKL25Z doesn't
exist and should have been CONFIG_SOC_MKL25Z4, However its not
necessary to define this at all since it implied by the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We had a comment related to the #endif for CONFIG_USB_DC_STM32 however
the comment said CONFIG_USB_DC_STM, so fix it to match the ifdef.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
CONFIG_BOARD_STM32_NUCLEO_{L432KC,L476RG} where set in the respective
board defconfig files, however these symbols don't exist. We can just
remove them from the defconfig as we'll get the board Kconfig symbol
defined by default when selecting that board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SPI_DW_INTERRUPT_SEPARATED_LINES symbol was removed and replaced by
SPI_DW_PORT_{0,1,2,3}_INTERRUPT_SINGLE_LINE in commit 423f0095c7
("drivers/spi: Specify options per-port on DW driver"), but an
assignment to it remains.
Remove the assignment and set SPI_DW_PORT_0_INTERRUPT_SINGLE_LINE to 'n'
instead. The Arduino has a single SPI port.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The Kconfig option TOOLCHAIN_VARIANT (not to be confused with
ZEPHYR_TOOLCHAIN_VARIANT) is a legacy configuration option that has
very few use-cases and can easily be dropped.
It's functionality is easily covered by CONFIG_X86_IAMCU and
ZEPHYR_TOOLCHAIN_VARIANT.
This commit removes all references of it from Zephyr.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The kl25z does not have the same spi hardware as the k64f and therefore
cannot use the same spi driver. Remove all references to spi for the
kl25z soc and frdm_kl25z board until we have a valid spi driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This commit adds a sample application using OpenAMP for remote procedure
calls on the LPCXpresso54114. It is adapted from the RPMsg-Lite sample
application added in PR #5960, and uses the IPM driver to provide
interprocessor interrupts.
Signed-off-by: Kristian Klomsten Skordal <kristian.skordal@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The current method of setting the openocd runner arguments works for
direct invocation from the command line, but the values that are
written to the CMake cache are not properly separated and are
difficult to parse, due to the fact that in several cases, option
values contain spaces.
Adjust these runner arguments so that the options and their values are
separate list items. This makes it possible to parse them accurately
from the CMake cache.
No functional changes.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
This target is already using the rbtree as part of CONFIG_USERSPACE,
so it incurs no code size overhead (actually it's a little smaller)
when using the scalable scheduler and waitq implementations.
The change also gets us test coverage of those choices on a default CI
target.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Use the named choices feature introduced by PR #6966
and configure LSM6DSL on ArgonKey board.
The two named choices introduced in LSM6DSL are:
- LSM6DSL_BUS_TYPE (default LSM6DSL_I2C)
- LSM6DSL_TRIGGER_MODE (default LSM6DSL_TRIGGER_NONE)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This patch adds dts support to lps22hb/hts221/vl53l0x
I2C sensors as well as lsm6dsl SPI sensor.
Since some info, like gpio for irq triggering or SPI bus
characteristics, may be provided through dts, they need
to be made optional in the LSM6DSL driver by usage of
macros like HAS_DTS_SPI_PINS or HAS_DTS_SPI_DEVICE.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit gets rid of the 'option env="ENV_VAR"' bounce symbols.
"$FOO" now expands directly to the value of the environment variable
FOO, instead of to the value of the Kconfig symbol FOO.
This change is likely to soon appear in the C tools as well. Those
'option env' symbols always seemed kinda pointless, and have broken
dependency handling due to forcing symbol evaluation during parsing,
before all the symbols have even been seen.
Compatibility with the C tools could be retained by naming all
'option env' symbols the same as the environment variable they
reference.
This commit also updated the Zephyr documentation to explain the new
behavior. It's relevant for $ZEPHYR_BASE and out-of-tree Kconfig
extensions.
Commit message from Kconfiglib (cbf32e29a130d)
==============================================
Make "$FOO" directly reference the environment variable $FOO in e.g.
'source' statements, instead of the symbol FOO. Use os.path.expandvars()
to expand strings (which preserves "$FOO" as-is if no environment
variable FOO exists).
This gets rid of the 'option env' "bounce" symbols, which are mostly
just spam and are buggy in the C tools (dependencies aren't always
respected, due to parsing and evaluation getting mixed up). The same
change will probably appear soon in the C tools as well.
Keep accepting 'option env' to preserve some backwards compatibility,
but ignore it when expanding strings. For compatibility with the C
tools, bounce symbols will need to be named the same as the environment
variables they reference (which is the case for the Linux kernel).
This is a compatibility break, so the major version will be bumped to 6
at the next release.
The main motivation for adding this now is to allow recording properties
on each MenuNode in a clean way. 'option env' symbols interact badly
with delayed dependency propagation.
Side note: I have a feeling that recording environment variable values
might be redundant to trigger rebuilds if sync_deps() is run at each
compile. It should detect all changes to symbol values due to
environment variables changing value.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add MCUX IPM sample application. It can be run on lpcxpresso54114
board at the moment.
We first build the slave core image out of the remote/ dir than the
primary core image is build which includes the slave core image.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add driver for MCUX mailbox which can be used for lpcxpresso54114
and other lpc and kinetis socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Add a board port to allow creation of "firmware" code that will run on
the slave core (Cortex-M0+).
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Updates documentation for the frdm_k64f, hexiwear_k64, and usb_kw24d512
boards to reflect that they now support a watchdog driver. Updates the
board yamls similarly for sanitycheck.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds the configuration, driver, and HAL changes required
to implement a MCUX based RTC driver for the NXP Kinetis KW41Z.
Signed-off-by: Andy Gross <agross@kernel.org>
This patch adds some DTS information to flesh out the NXP Kinetis
based RTC blocks. DTS fixups were added as well to match up the driver
usage to the DTS output.
Signed-off-by: Andy Gross <agross@kernel.org>
Be more obvious about the entropy_native_posix driver
being only a test utility which does not generate real
entropy.
Fixes: #6388
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Kconfig keyword GPIO_AS_PINRESET is common for whole nrf52 series.
This patch move it to the series Kconfig.soc file.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add use-prop-name to disconnect-gpios property in st,stm32-usb
yaml, in order to generate friendly name for the definitions.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
In order to run the Simple Management Protocol (SMP) over UART, a DTS
symbol named uart-mcumgr needs to be defined on the board. Enable this
for all Nordic Development Kits.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As part of the prep to support the M0+ core on lpcxpresso54114, we
rename the lpcxpresso54114 board port to lpcxpresso54114_m4 to be
explicit.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename various SoC related defines and files from just being LPC54114
to LPC54114_M4. This is in prep for supporting a build for the second
core on the LPC54114 (the Cortex-M0+).
* Renamed Kconfig SOC_LPC54114 to SOC_LPC54114_M4
* Renamed Kconfig.defconfig.lpc54114 to Kconfig.defconfig.lpc54114_m4
* Introduced nxp_lpc54xxx_m4.dtsi based on nxp_lpc54xxx.dtsi
* Moved some pinmux related defines into SoC code.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use DT to generate defines for irq and reset gpios in bluetooth
controller node.
Define a bt alias to allow generation of defines with friendly
names.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
* add pmod mux init to config the pmode interfaces
to the specific functions
* without pmod mux init, all pmod interfaces will be
GPIO, no interfaces for spi/i2c0/i2c1/uart0
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* add gpio, i2c, spi definitions
* optimize and bug fix the dts.fixup
* optimize and bug fix the em_starterkit related definitions
in dts folder
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* em9d is configured to use ccm, and no sram
* choose dccm as virtual sram to generate the correct definitions
of CONFIG_SRAM_XXX which are used in many places, e.g. lib-hooks.c.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The original em7d, em9d and em11d are different configurations of
em_starterkit. They have the same peripherals, e.g. uart, spi, gpio
, ddr. The differences of them are in arc core configurations, interrupt
number assignment.
So em7d, em9d and em11d can be viewed in the same SoC family or SoC
series.
Referring other arch's implementation, this commit merges em7d, em9d
and em11d into the same SoC, named snps_emsk. This will eliminate
unnecessary duplication and make it easier for future maintainment.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The zephyr.exe created when building a native POSIX application can take
some parameters that are documented in the "board" document, so add a
reference to that documentation here.
fixes: #6384
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
patch removes Kconfig defines for RAM and ROM size in x86. Instead
these values are derived from dts.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Adds dts bindings for the mcr20a wireless transceiver. The frdm_k64f
board supports the mcr20a via an Arduino shield, therefore the dts node
is added to the board dts. The kw2xd is a SiP and thus the mcr20a dts
node is added to the soc dts.
The networking samples using prj_frdm_k64f_mcr20a.conf have been broken
since the refactoring of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Configures the frdm_kw41z board to mux spi signals on pins PTC16-19.
Updates the board document to reflect that spi is supported on these
pins.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts bindings for the fxas21002 interrupt pins to all boards that
have this sensor.
The fxas21002 driver is currently only aware of one sensor interrupt
pin, therefore the routing of INT1 or INT2 to the driver is handled in
each board's dts.fixup.
The fxas21002 sample application has been broken since the refactoring
of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts bindings for the fxos8700 interrupt pins to all boards that
have this sensor. The frdm_k64f and hexiwear_k64 connect both sensor
interrupt pins to the mcu, but the frdm_kw41z connects only one.
The fxos8700 driver is currently only aware of one sensor interrupt pin,
therefore the routing of INT1 or INT2 to the driver is handled in each
board's dts.fixup.
The fxos8700 sample application has been broken since the refactoring of
the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add cs, irq and reset gpios description in spbtle controller
node and use generated defines instead of Kconfig symbols.
Define a bt alias to allow generation of defines with friendly
names.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Indexed defines were systematically generated even when there
was only one element to generate.
So we ended up generated a lot of _0 defines.
Then we needed to generate aliases to these _0 indexed defines,
in order to get useful defines.
For instance:
#define GPIO_LEDS_0_GPIO_FLAGS_0 4
#define GPIO_LEDS_0_GPIO_PIN_0 5
#define GPIO_LEDS_0_GPIO_FLAGS GPIO_LEDS_0_GPIO_FLAGS_0
#define GPIO_LEDS_0_GPIO_PIN GPIO_LEDS_0_GPIO_PIN_0
This commit allows to generate _0 indexed define only if a
property has more than one elements to define.
Aliases generation to _0 indexed defines are also removed.
Note: IRQ are left untouched since this is frequent to handle
multiple IRQs in a driver
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The disco_l475_iot1 board uses the vl53l0x sensor in XSHUT pin
master control configuration mode. So, it has to explicitly
enable it now.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Adds a board-level config option to select whether the code gets linked
into internal instruction tightly coupled memory (ITCM), external
hyperflash, or external qspi flash. The default is ITCM.
Note that we are not yet building an image vector table (IVT) into the
image, therefore the zephyr binary is not bootable by the SoC ROM as-is.
However, the DAPLink firmware prepends an IVT to the image when you use
its drag-and-drop feature to program flash, and this results in a
bootable zephyr application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds flexspi and semc memory controllers to the i.MX RT SoC. Adds
hyperflash, qspi, and sdram external memories to the mimxrt1050_evk
board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Previously, when !CONFI_XIP, BOOTLOADER_SRAM_SIZE was defaulted
to 16 (K), reducing the size of SRAM available for the program.
Also, though it has no effect, the value for SRAM start in the
dtsi file was incorrect.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The frdm_k64f board document incorrectly listed spi signals on PTCD
pins, which don't exist. They should be on PTD pins.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Until now, Zephyr has used a patched Kconfiglib that turns 'source' into
a globbing source (by replacing 'source' with 'gsource' at the token
level). There's two problems with this:
- The patch needs to be maintained separately
- Misspelled filenames are silently ignored, as they look like glob
patterns that don't match anything
Fix it as follows:
1. Replace all 'source' statements that use wildcards with 'gsource'
2. Remove the custom Kconfiglib patch so that 'source' no longer globs
The sed pattern '/source.*[*?]/s/source/gsource/' was run over all
Kconfig* files to do the replacement.
source's that use environment variables that might contain glob patterns
were manually changed to gsource.
Building the docs in doc/ is a good test, as doc/Makefile deliberately
sets the environment variables to glob up as many Kconfig files as
possible.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
This patch adds DT description of generic storage flash
partition. This fixes issue #7227.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
FS_FLASH_MAP_STORAGE keyword enables the storage partition,
but it was depend on flash_map module which is unused by
NFFS. This patch makes it independent thanks
to it is possible to enable the storage partition
without flash_map module.
FS_FLASH_MAP_STORAGE was renamed to
CONFIG_FS_FLASH_STORAGE_PARTITION
as it is independent for flash_map.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Add support to enable test application selectively based
on defconfig
Change-Id: I8111750ff099edd95ffa22c6e312999c801678ea
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A brief description about intel_s1000 and ways to connect,
flash, debug etc.
Change-Id: I459c64d8d9574bc3511da7f983d68e044cacc1d0
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable the CAVS I2S on intel_s1000. Also, introduce a test to
validate I2S in ping-pong and normal modes.
Change-Id: Iea78e22cedc7724c1c2e821c68d7030cc0a65047
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable the CAVS DMA on intel_s1000. Also, introduce a test to
validate the DMA.
Change-Id: I2ff233c45cfd8aea55e254d905350a666aa649a0
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patchset creates Debug, Debugserver and Flash scripts
ensuring support in the ZephyrBinaryRunner mode.
Change-Id: Ib4f7820b1c6a045bd67cf4a031be99cf61e65eca
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000 has multiple levels of interrupts consisting of core, CAVS
Logic and designware interrupt controller. This patchset modifies
the regular gen_isr mechanism to support these multiple levels.
Change-Id: I0450666d4e601dfbc8cadc9c9d8100afb61a214c
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000 makes use of DesignWare IP for I2C.
Change-Id: Ie091318c5959b95e1febeb5cefa440f35a6d144b
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable GPIO handling for intel_s1000. It uses a DesignWare IP.
Change-Id: I522534935e4ef3a56d93aca669f6de961d927481
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000 uses DesignWare IP for UART. National Semiconductor
16550 (UART) component specification is followed in this IP.
Change-Id: Ied7df1dc178d55b6dbe71d729d6383ba07274ea4
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
intel_s1000_crb board makes use of the intel_s1000 SoC. It has
a built-in ROM which gets executed upon applying power. It then
executes the secondary bootloader followed by the FW (like zephyr).
Change-Id: If334c359b4372a56997c3b2e1eb9250e80847f07
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Following changes are necessary to use LP3943 LED driver present
in 96Boards Neonkey board
1. Enable I2C_3 interface
2. Reduce the speed of I2C_3 bus on 96Boards Neonkey. Due to some
design quirks, on board LP3943 LED driver connected to I2C_3
operates only at Standard speed of 100KHz.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
These are a direct copy from the nrf51_pca10028 board, since it's also
an nRF51 and has the same size flash.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The allowed values for APB2 prescaler are: 1, 2, 4, 8, 16.
Set APB2 prescaler value to 1 in boards defconfig.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The NFFS partition at the end of flash is also useful for any other
file system or even the Flash Circular Buffer (FCB). Rename the
partition from 'nffs_partition' to 'storage_partition' and make it
depend on a new hidden Kconfig entry which the relevant users will
select (such as NFFS and FCB).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To prepare to upcoming dtc v1.4.6, fix warnings in dts files.
This commit addresses the following warning:
"unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In some BLE use cases, using MSI driven SYSCLK is required.
Rework board Kconfig.defconfig in order to enable use of 2
alternate default clock configurations.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We have been combining imported mcux drivers into a flattened directory
structure to maximize driver reuse, but the introduction of additional
nxp soc families (lpc and imx) to zephyr has introduced driver naming
conflicts. This caused us to rename and modify imported files, such as
fsl_gpio.c/h, to make them unique across all three nxp soc families.
This makes updating the the mcux drivers complicated, especially for the
lpc family.
Reoganize the mcux drivers into soc family subfolders, so we can just
copy all the drivers from an mcux distribution (which is done on an
soc-basis) into the appropriate soc family folder. Undo all of the
naming changes that occurred when lpc and imx drivers were originally
imported. Undo the accidental squashing of the kinetis watchdog and dcdc
drivers that occurred when the imx drivers were introduced.
The drawback to this approach is that we have duplicate files when the
same hw ip modules exist in multiple soc families, however there are
only few cases where this occurs, such as fsl_lpuart and fsl_trng.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes#7137
Enables the i2c drivers for these boards.
Required to enable i2c with these boards.
Tested samples/bluetooth/beacon for nrf52_pca10040
with i2c enabled.
Parameters used for enabling i2c:
CONFIG_I2C=y
CONFIG_I2C_0=y
CONFIG_I2C_NRF5=y
CONFIG_I2C_NRF5_0_GPIO_SCL_PIN=6
CONFIG_I2C_NRF5_0_GPIO_SDA_PIN=7
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.com>
Adds led and button dts nodes to all kinetis boards and removes the
now unused preprocessor macros from board.h.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update names of the configuration entries so that the new nRF SPIS
driver can be used on this board.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The test "net/utils" fails to build on nucleo_f103rb
due to "region `SRAM' overflowed by 8 bytes.
Disabling PWM at the board level to build the test.
Moreover, according to issue #6858, we will only configure
board valuable HW and connectors on board level and the
user should enable what is needed on application level.
Reported-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
boards/x86/arduino_101/arduino_101_defconfig currently enables
CONFIG_UART_QMSI_0_HW_FC (HW flow control on UART 0), but doesn't enable
CONFIG_UART_QMSI_0 (the UART itself), which is a direct dependency.
This means CONFIG_UART_QMSI_0_HW_FC remains disabled despite the request
to enable it, and kconfig.py prints a warning.
Enable CONFIG_UART_QMSI_0 in the arduino_101_defconfig.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Underscore ('_') isn't a valid char for alias names based on the device
tree spec. Newer dtc compilers flag this as a warning so lets clean it
up. Replaced '_' with '-' to keep things simple.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The TRNG IP block in the KW41Z is really an entropy source and not
intended to be used as a general purpose random number generator
source. The block has 15 slots to read from and when the last slot
is read it has to regenerate the 15 numbers. This process takes
3-5 seconds and is blocking. The change here is to use the TRNG as
an entropy source to the XOROSHIRO pseudo random number function
and then have the KW41Z use XOROSHIRO for random number generation.
Signed-off-by: David Leach <david.leach@nxp.com>
When we added support for the HiFive1 board we forget to make sure it
had a board yaml file. Add the file so we get sanitycheck running on
the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Colibri iMX7D Computer on Module with Colibri Evaluation Board
configuration supports the following hardware features on the Cortex M4
Core:
+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component |
+===========+============+=====================================+
| NVIC | on-chip | nested vector interrupt controller |
+-----------+------------+-------------------------------------+
| SYSTICK | on-chip | systick |
+-----------+------------+-------------------------------------+
| UART | on-chip | serial port-polling; |
| | | serial port-interrupt |
+-----------+------------+-------------------------------------+
The default configuration can be found in the defconfig file:
boards/arm/colibri_imx7d_m4/colibri_imx7d_m4_defconfig
Other hardware features are not currently supported by the port.
Connections and IOs:
The Colibri iMX7D Computer on Module with Colibri Evaluation Board
was tested with the following pinmux controller configuration.
+---------------+-----------------+---------------------------+
| Board Name | SoC Name | Usage |
+===============+=================+===========================+
| UART_B RXD | UART2_TXD | UART Console |
+---------------+-----------------+---------------------------+
| UART_B TXD | UART2_RXD | UART Console |
+---------------+-----------------+---------------------------+
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
All boards based on STM32 should use dts for I2C and SPI.
Move CONFIG flags selection from boards to arch and select them
for all STM32 SoCs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We run the same tests over and over again in different qemu
environemnt. Optimize the list to reduce redundant testing of the same
protocols. Picked qemu_x86 because it has userspace enabled.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
We are testing and building this already using qemu_x86, no need to
build the same thing all over again.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A Kconfig option is added for setting the initialization priority.
This is done to make the initialization priority requirements in
nrf52_pca20020 board power up sequence clearer.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
A documentanion file is added for Thingy:52. This document only
discusses the currently supported features of the board. The omissions
include the audio features and sensors which don't have a working driver
in tree.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
A new board configuration is added for Thingy:52, also known as
PCA20020. This includes support for some of the on-board sensors, and
other peripherals such as the on-board GPIO expander.
The board power rail sequencing is also implemented, as the rails need
to be powered up in a correct order and before certain device driver
init calls are made.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
The test "net/utils" fails to build on olimexino_stm32
due to "region `SRAM' overflowed by 192 bytes".
Disabling I2C and SPI on board level the test build fine.
Moreover, according to issue #6858, we will only configure
board valuable HW and connectors on board level and the
user should enable what is needed on application level.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Added support for the HiFive1 board from SiFive
Signed-off-by: Tomasz Michalak <tmichalak@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Signed-off-by: Tomasz Jurtsch <tjurtsch@antmicro.com>
As we have E70 ethernet driver enabled, we need to enable the
generic ethernet L2 driver too so that the ethernet is actually
useful.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Refer to the samples/net/eth_native_posix sample app
and mention that this driver only works on Linux
with admin rights
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
QMSI is not updated to latest SPI API. Switching to native DW driver,
until we find a way either to update the shim drivers in a
non-performant way, or updating QMSI itself enabling support for
scatter-gather type of buffers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As the native_posix board has ethernet driver, then enable it by
default if networking is enabled in prj.conf file. This way we can
use generic networking config file when running the application
for native_posix board.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the value argument to set_ifndef() may be unset, the entire value
must be double-quoted to avoid a CMake syntax error.
Fix call sites which don't handle this, or which otherwise make
non-idiomatic use of this function.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Add support for getting some basic params from the DTS for the UART.
The ns16550 driver still needs to be updated to get IRQ and address
info from DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all ARC SoCs we can remove code associated with !HAS_DTS and
select HAS_DTS at the architecture level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add initial device tree support for the em{7,9,11}d SoC and associated
em_starterkit boards. The device tree at this point specifies cpu core,
memory, interrupt controller, uart's and i2c controllers.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Applying the change to relevant arch/boards, either in their Kconfig or
the dts specific files.
Taking the opportunity in dw driver to rename the variable the same way
as they are everywhere else in the code (s/dev/dw and s/port/dev) in
init function.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The SAM0 SoC was switched to use DTS for SPI configuration. Update
documentation for the SAM0 based boards to use the correct SPI
controller device names.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
As the board has ethernet chip it makes sense to enable the
ethernet support by default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
New revision (SWCU117H) got published and the old one (supposedly
SWCU117G) is no longer available.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
This creates zeth network interface in your host and allows user
to send and receive data sent to this network interface.
Fixes#6007
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Currently, it seems that only boards with smaller amount of RAM
get a value for "ram" property, and very few boards have "flash"
defined. However, to test bigger sample applications, it's helpful
to have these properties universally defined.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Added support for Waveshare BLE400 board.
Tested it with the following samples and confirm it work.
- samples/basic/blinky
- samples/basic/button
- samples/basic/fade_led
- samples/basic/threads
Signed-off-by: Roman Tataurov <diytronic@yandex.ru>
Describe in documentation few methods that can be used by
users to flash the ArgonKey with a binary image.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
According to a conversation with @carlescufi and @finikorg, the
zephyr codebase should only use the Linux Foundation USB vendor
ID. The USB vendor IDs and product IDs in the board definitions
are an obsolete leftover from old code and no longer needed.
Signed-off-by: Iván Sánchez Ortega <ivan@sanchezortega.es>
Move the dts.fixup back to board dir in prep for support mps2_an521.
The memory maps between the two mps2_an385 and mps2_an521 differ greatly
so its easier to just keep the fixup files with the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add initial support for NUCLEO-L073RZ board.
This is a typical Nucleo-64 board, so most files are reused
from already supported Nucleo boards with small changes.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
SoC dts fixups are added and the i2c_nrf5 driver is modified to use
the values generated from the device tree.
The I2C_*_DEFAULT_CFG and I2C_*_IRQ_PRI options are removed from board
defconfigs. Bitrate and IRQ priority are configured using using the
device tree instead.
HAS_DTS_I2C is selected on all nrf5 boards to prevent generation of
conflicting defines from Kconfig.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
The i2c controller nodes are enabled in the board specific dts files
on boards where the controller was enabled in the board Kconfig.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
This commit changes the Arduino Zero pinmux configuration to use PA12
as MISO.
According to the schematic, the Arduino Zero provides a SPI bus on
SERCOM4 with the following pads/pins:
- MISO: PA12/pad0 (pin 21)
- MOSI: PB10/pad2 (pin 19)
- SCK: PB11/pad3 (pin 20)
The MISO signal is incorrectly labeled as PB12_S4_SPI_MISO on the
schematic. It should be labeled PA12_S4_SPI_MISO.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Nucleo-64 boards do not have X3 crystal by default, so HSE is clocked
from MCO output of ST-LINK, and CONFIG_CLOCK_STM32_HSE_BYPASS should be
enabled. STM32F0 HSE somehow magically works even without that, but
to do so is the right thing.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Since not all boards enable all devices, we typically have the SoC dtsi
file have a device marked with status = "disabled" and have the
board.dts explicitly enable with status = "ok". Update it so USB on
Atmel SAMD21 work this way.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move IRQ numbers into device tree so we can remove soc_irq.h. We are
already using IRQ defines generated form the DTS so no point in having
soc_irq.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added device tree support to the ARM SBCon I2C controller. We utilize
the compatiable "arm,versatile-i2c" the binding from Linux for the some
peripheral block.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The legacy SPI API was turned back on for the Adafruit Feather M0
Basic Proto when the SAM0 SoC was switched to using DTS for SPI. This
commit turns it back off.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
ArgonKey board is a 96boards sensor hub platform for all 96Boards
compliant family products. The ArgonKey packs a Cortex-M4 chip
together with a set of motion, environmental and ambiental sensors
and can be used as a development platform for many different
applications.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Switch the SoC device tree to define a single entry per SERCOM instead
of one per mode.
Define a Device Tree binding for the SAM0 SPI and use it instead of
Kconfig for enabling / disabaling instances
Switch the Arduino Zero, Adafruit Feather M0 Basic Proto, and
Trinket M0 to use the new defintion.
Add the APA102 LED that's on the Trinket as a test.
Signed-off-by: Michael Hope <mlhx@google.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Changed the default UART used for the console. You used to have to
use wires on the J4 header. Now you can use the UART provided by the
Segger USB composite device.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Fixed the output string in the documentation for
the SAM E70 Xplained. The output for the hello_world
sample wasn't correct.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Support the ST STM32F0DISCOVERY board with STM32F051R8T6 SoC
Tested with:
- `samples/basic/blinky`
- `samples/basic/button`
Includes flash config in `stm32f0_disco.rst` for use with mcuboot
Signed-off-by: Nathan Tsoi <nathan@vertile.com>
The Feather M0 Basic Proto is an Atmel SAMD21 based development board
with USB, UART, SPI, LED and onboard lithium polymer battery charger.
Use of the Adafruit stock photo (adafruit_feather_m0_basic_proto.jpg)
for the board documentation was approved by Adafruit Industries.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
As USB port is present on the board, and pinmux configured,
add USB support in board dts file.
Configure Ethernet oer USB as default net i/f
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Change TICKS_PER_SEC from 1000 to 100
* em_starterkit is a FPGA board with cores running at max 30 Mhz.
1000 ticks per second is a little heavy for it.
* the tests/kernel/common requires 200 ticks per second at most,
or the testcase will stall.
disable the generation of bin file.
* there is no flash in em_starterkit
* there is huge gap between ICCM and DCCM which will cause the bin
file too large, alomst 2GB
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
According to STM32-E407.pdf (Revision I, June 2017), CON1 RST is
connected to processor pin #25, not #23.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
The arm qemu platform has limitiations as we get into more complicated
features like userspace support. Add one hardware platform to catch
issues in sanitycheck for development of such features.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We assumed that ${BOARD} and ${BOARD_FAMILY} are always the same and
thus interchangeable. That isn't always the case so use ${BOARD} proper
for when we mean the exact BOARD name we are building for vs the
BOARD_FAMILY.
We also add .dts files for board variants within a board family, such
that we have a .dts matching each board name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/arm/soc/<SOC>/dts.fixup so
we remove duplication in the boards and only have board specific
defines in boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/x86/soc/atom/dts.fixup so we
remove duplication in the boards and only have board specific defines in
boards/x86/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/x86/soc/ia32/dts.fixup so we
remove duplication in the boards and only have board specific defines in
boards/x86/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/x86/soc/intel_quark/quark_se/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/x86/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arc/soc/quark_se_c1000_ss/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arc/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added a basic command line parameter parsing framework
Added the following options by now:
--stop-at=<time>: Auto-stop after <time> seconds
--seed=<seed> : random seed for entropy device
--testargs : any argument that follows is ignored in top level
and made available thru
native_get_test_cmd_line_args()
All command line parameters are still avaliable by calling
native_get_cmd_line_args(), but now you can also call
native_get_test_cmd_line_args() to get whatever was set after
--testargs
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The space referred to in these comments was once truly reserved for
the application: no zephyr partition would ever use it.
Now, though, that's not the case, since NFFS will use these sectors
when enabled.
Just delete the comments.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Let's point users at the latest documentation on flash
partitions from each of the board files, rather than duplicating some
of the information in it.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Move common SoC dts.fixup defines into
arch/arm/soc/atmel_sam/<BAR>/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/arm/soc/nxp_imx/rt/dts.fixup
so we remove duplication in the boards and only have board specific
defines in boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/kwx/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/kl2x/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_lpc/lpc54xxx/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/k6x/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implements interrupt driven UART for the serial driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Move common SoC dts.fixup defines into
arch/arm/soc/ti_simplelink/<BAR>/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Current configuration was choosen to avoid colliding with existing ones
for i2c and uart, but others can be used.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Current configuration was choosen to avoid colliding with existing ones
for i2c and uart, but others can be used (see
drivers/pinmux/stm32/stm32_f0.h)
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Configure SPI using DT for the following STM32 boards:
96b_neonkey
nucleo_f091rc
nucleo_f334r8
nucleo_f401re
nucleo_l432kc
nucleo_l476rg
SPI nodes in <board>.dts file are populated matching boards existing
pinmux default configuration and enabled in Kconfig.defconfig if
SPI is enabled.
For nucleo_l476rg board SPI2 and SPI3 nodes are not yet added, because
of missing pinmux defines.
Fixes#5836
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
The xtensa-asm2 work included a patch that added nano_internal.h
includes in lots of places that needed to have _Swap defined, because
it had to break a cycle and this no longer got pulled in from the arch
headers.
Unfortunately those new includes created new and more amusing cycles
elsewhere which led to breakage on other platforms.
Break out the _Swap definition (only) into a separate header and use
that instead. Cleaner. Seems not to have any more hidden gotchas.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
* add the implementation of syscall
* based on 'trap_s' intruction, id = 3
* add the privilege stack
* the privilege stack is allocted with thread stack
* for the kernel thread, the privilege stack is also a
part of thread stack, the start of stack can be configured
as stack guard
* for the user thread, no stack guard, when the user stack is
overflow, it will fall into kernel memory area which requires
kernel privilege, privilege violation will be raised
* modify the linker template and add MPU_ADDR_ALIGN
* add user space corresponding codes in mpu
* the user sp aux reg will be part of thread context
* When user thread is interruptted for the 1st time, the context is
saved in user stack (U bit of IRQ_CTLR is set to 1). When nest
interrupt comes, the context is saved in thread's privilege stack
* the arc_mpu_regions.c is moved to board folder, as it's board
specific
* the above codes have been tested through tests/kernel/mem_protect/
userspace for MPU version 2
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is one way we can support out of tree board definitions. Basically
all this needs is a board definition in the application source directory
that follows the same structure we have in the main Zephyr tree (also
allowing multiple custom boards). An application tree would look like
this for example:
boards/
CMakeLists.txt
prj.conf
README.rst
src/
with boards following the same structure as in Zephyr:
.
├── boards
│ └── x86
│ └── arduino_101
│ ├── doc
│ │ └── img
│ └── support
└── src
To use this, you need to specify the BOARD_ROOT variable on the command
line when building:
cmake -DBOARD=<board name> -DBOARD_ROOT=<path to boards> ..
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Commit 247782a7b3 moved the sam0 UART
and SPI configuration into pinmux. Using these drivers without pinmux
causes the kernel to skip the pin configuration.
Tested on arduino_zero.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
We want to support other toolchain not based on GCC, so the variable is
confusing, use ZEPHYR_TOOLCHAIN_VARIANT instead.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove spurious console code block to fix formatting of the following
zephyr-app-commands directive. While I am here, fix the indentation of
the two zephyr-app-commands directives.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Very brief documentation of the board as a placeholder, more info on
supported features will follow.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Atmel SAMD21 series was classified too broadly as SAMD.
This patch names it correctly to make room,
for other members of SAMD series
Signed-off-by: Sean Nyekjaer <sean@nyekjaer.dk>
Bugfix in the tickless mode part:
During _time_idle_exit it was not announcing to the kernel the
already passed silent ticks, but it was left for the tick interrupt
itself.
This did not cause any trouble so far as there was only the timer
interrupt in this board.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Also pull out the SERCOM pads configuration to defines. Note that the
SAM0 has a two level configuration - a signal (like TX) is mapped to a
pad, and then a pad is mapped to a function on a pin.
Signed-off-by: Michael Hope <mlhx@google.com>
nucleo_f413zh was missing some files to support flash with
openocd. Fix this lack and update doc.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
nucleo_f412zg was missing some files to support flash with
openocd. Fix this lack and update doc.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Just some exclusions to coverage in code which cannot be
reached, or can only be reached in error conditions
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Added possibility to reconfigure CONFIG_SYS_CLOCK_TICKS_PER_SEC
for the native_posix board (before it could only be 100)
+
Fixed tickless idle support
+
Minor fixes in irq wrapping
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
MinnowBoard has an uppercase "B" in its name. Also added a link to the
config option mentioned.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
CONFIG_I2C_NRF5_GPIO_SDA_PIN and CONFIG_I2C_NRF5_GPIO_SCL_PIN are
replaced with port specific versions. Board defconfigs relying on the
original names are updated. The driver is also modified to pass the
configure values to registers.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Add a reference to flashing and booting so it can be used by minnowboard
and other boards.
Apply minor layout fixes.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Pin multiplexing is a function of the PORT peripheral. This change
defines a separate pinmux device at the same address as the PORTs
themselves.
Signed-off-by: Michael Hope <mlhx@google.com>
To avoid indeterministic behaviour of the tests
which leads to changing coverage reports, let's
finish the tests exectuion as soon as they pass
or fail.
Also let's return 0 to the shell if the test passed,
and 1 if it failed.
(Reverting
f9af42f078c93eca8b9f461f91b6cafddb57a35d and
07c9163f67
)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Now the native console driver also handles stdin
so we can drive the shell from the command line,
a pipe or a file
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Adds dts nodes and fixups for the fxos8700, fxas21002, and max30101
sensors to the hexiwear_k64 board. Tested with:
- samples/sensor/fxos8700
- samples/sensor/fxas21002
- samples/sensor/max30101
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts nodes and fixups for the fxos8700 sensor to the frdm_kw41z
board. Tested with samples/sensor/fxos8700
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts nodes and fixups for the fxos8700 sensor to the frdm_k64f
board. Tested with samples/sensor/fxos8700
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hts221 sensor driver was implicitly made dependent upon the
disco_l475_iot1 board when it was converted to dts, so build the
associated sample only for this board. This issue was encountered when
adding sensor dts support to nxp boards, which don't have hts221.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
We should enable CONFIG_POLL on application level when
we want to use SPI transceive_async() function.
This patch removes it from disco_l475_iot1 default
configuration.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
rename main_clean_up() to posix_exit() for consistency
with all other global functions of this architecture
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The jlink commander failed to program flash with auto speed on the
usb_kw24d512 board, so set the speed explicitly on this board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that the jlink runner supports the flash command, set
BOARD_FLASH_RUNNER when the OpenSDA or LPCLink debug adapter is
programmed with jlink firmware.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds support for the 'flash' command to the jlink runner so we can flash
via 'make flash'. This works by generating a temporary jlink commander
script file and passing the script to the jlink commander executable.
Previously, the only way to flash with jlink was via 'make debug'.
Includes support for DT based flash address, and an optional mass erase
before loading the flash.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enable and configure I2C1.
This configuration enables ready to use compatibility
with expansion shields based on Arduino type connectors
Additionally, fix comment on clock speed in board _defconfig
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Applies to #4008 and #5159 for this board. Problem is that the
button interrupt callback was only firing once. Solution is to
set the pin pull up flag to GPIO_PUD_PULL_UP.
Signed-off-by: Anders Pitman <tapitman11@gmail.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This moves and merges the existing board-level dts.fixup files
for STM32 L4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
disco_l475_iot1 boards fixup blocks for devices connected via SPI
and I2C stay in board level dts.fixup file, because they are board
specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F3 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F1 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
96b_carbon boards fixup block for Bluetooth HCI device via SPI
stays in board level dts.fixup file, because it is board specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F0 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Corrected the board name in the configuration short
description string. It was the old Simple_process name which was
replaced with native_posix
Corrected also the comment/title in the "Board Options" menu
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The native SOC Kconfig file was still referring to the old
configuration option SOC_INF_CLOCK which was replaced with
SOC_POSIX.
This produced a warning on configuration which is now fixed
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
When we updated the Nordic SoCs for getting flash controller label/name
from dts, we missed updating the 96b_nitrogen/dts.fixup file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To get coverage data from all samples and tests, enable this by default.
Right now we only get coverage data from tests, however many samples we
currently have can run natively and can generate more coverage and
testing.
This should be removed once we have tests provide better coverage.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Quite a lot of improvements in the native_posix board
documentation:
* Added TOC
* Reordered
* Given much more emphasis to its limitation
* Added subsection explaining how to overcome some of these
limitations
* Added rationale section
* Added section comparing this port with QEMU and ISSs
* Corrected build example (this port cannot be compiled on
Windows, regression from commit
e62ee6ab3c )
* Added note about it not working on W10 WSL (#5762)
* Several other minor fixes
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
For tests (CONFIG_TESTS) do not slow down the execution
to real time.
For samples, we assume they are interactive and therefore it is
still preferred to run them at real time.
This speeds up the native_posix part of sanitycheck
by ~50% (more the faster the computer)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Move bluetooth module SPI port related configuration
to dts and generate dts based defines on 96b_carbon
and disco_l475_iot1.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
references to pdf files (e.g.,
www.st.com/resource/en/reference_manual/dm00091010.pdf)
were missing the http:// prefix so looked like a relative reference.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Adding 'config POLL' in Kconfig.defconfig creates a dependency
between CONFIG_POLL and board BOARD_DISCO_L475_IOT1 & SPI.
Remove this definition from the file and set CONFIG_POLL
in board _defconfig file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In Qemu 2.10 we can run this board configuration in Qemu directly. Make
this possible by setting the board configuration to allow emulation.
Until we have the latest QEMU in the SDK this can be used with a recent
QEMU like this:
$ mkdir build; cd build
$ cmake -DQEMU=/usr/bin/qemu-system-arm -DBOARD=mps2_an385 ..
$ make run
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some boards are supported natively by qemu. This option will allow us to
run tests using those platforms directly without having to go via a
dedicated qemu board definition.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In order to be able to document the build on Windows and UNIX
systems, slight variations are required on the app commands
that are used throughout the documentation system.
This includes getting rid of the prompt symbol and providing commands
for both UNIX and Windows operating systems.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
* arc MPUv2 is only available in em7d em starterkit version 22.
Add a default config for this to simply the config.
* The change of board version in menuconfig, e.g, version 23 to
v22, will not cause other options depending on board version
change automatically, users still need to change these options
manually. This is another reason to need a new default config file.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Refering the ARM's implementation, the initial support of memory
domain in ARC is added:
* changes in MPU drivers
* changes in Kconfig
* codes to configure memory domain during thread swap
* changes in linker script template
* memory domain related macro definitions
the commited codes are simply tested through
samples/mpu/mem_domain_apis_test.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Most boards enable the pinmux by default by setting CONFIG_PINMUX=y in
<board>_defconfig, but several boards did it in Kconfig.defconfig
instead. Several code reviews, such as #5043, have suggested using a
select in Kconfig.board to enable the pinmux, however this caused
warnings:
warning: (BOARD_LPCXPRESSO54114) selects PINMUX which has unmet direct
dependencies (BOARD_FRDM_K64F || BOARD_FRDM_KL25Z || BOARD_FRDM_KW41Z ||
BOARD_HEXIWEAR_K64 || BOARD_USB_KW24D512 || BOARD_GALILEO)
Fix how these boards enable the pinmux so they are more consistent with
other boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
quark_se_c1000_devboard already embeds a cc2520 which is a 2.4Ghz 15.4
radio chip. But if one want to try a sub-Ghz radio chip such as the
cc1200 on it, it will require to wire as this configuration expects it
to be done.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Defining TRIGGER_MODE choices in board Kconfig.defconfig files
brings unwanted dependency and warning messages when using sensors
on other boards.
Change sensor configuration by enabling wanted trigger choice rather
than redefining choice.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When Kconfiglib was introduced it caused a significant performance
issue. This patch uses pruning to mitigate the performance issue.
The pruning exploits the fact that before the Kconfig database is
parsed we already know what ARCH and BOARD has been selected. So in
theory we could prune away all Kconfig sources that are not related to
the current ARCH or BOARD. In practice, it is only the Kconfig sources
in zephyr/arch/$ARCH and zephyr/board/$ARCH/ that are easy to prune.
Still, that is quite a few Kconfig sources. For qemu_x86 this patch
reduced the number of parsed Kconfig source files from 632 to
272. This pruning resulted in a incremental reconfiguration (time
cmake ..) speedup of 21% (0.56s to 0.46) and a clean build speedup of
4% (Using board qemu_x86 and sample hello_world).
Furthermore, it should be easier to maintain ARCH's and BOARD's
out-of-tree since the user now has a mechanism to redirect where
Kconfig sources are found. But this has not been explored.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Updated previously broken links to emulation setup install, instructions
and Getting Started Guide.
Also added a few clarifications for the prerequisites setup.
Fixes#5601
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
* Added a figure explaining how layering of the posix arch
compares to the embedded builds
* One minor grammar change in last paragraph
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The native_posix board will accept command line arguments
which the application / test may pick by calling
native_get_cmd_line_args()
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Instead of accessing the environment variable ZEPHYR_BASE every time we
require accessing the source code root, use an intermediate variable
that has OS path separators correctly set to '/' to avoid issues on
Windows.
Note: This removes the ZEPHYR_SOURCE_DIR CMake variable. External
applications using that will need to change to use the new ZEPHYR_BASE
variable.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Old reference on driver's specific raw mode was still lurking around.
Removing those.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This was validated on the cc3220sf_launchxl board
using the Zephyr thermometer sample program
adapted to call the i2c driver directly, and fetching
samples from the on-board TMP006 temperature sensor.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
ETH_MCUX_0 needs to be turned on when CONFIG_NET_L2_ETHERNET is enabled.
If CONFIG_NET_L2_ETHERNET is disabled (e.g. when configured for 6loble),
then ETH_MCUX_0 should remain disabled.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
This board doesn't support `make flash` way of programming.
So, remove that from documentation.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Of these, only struct net_ipv6_nbr_data::send_ns is a descriptive
change:
send_ns is used for timing Neighbor Solicitations in general, not
just for DAD.
The rest are typo/grammar fixes.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Update board definitions with supported feature. This is temporary
until we have full coverage for device drivers in DTS, then we can use
DTS instead.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Native port now adds .exe to the generated ELF
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Right now we are hardcoded to only qemu, with the native port, we make
this more generic and support this in a plugin mode where a running has
its own cmake definitons implementing the various targets.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Environment variables should be checked with if(DEFINED
ENV{ESP_IDF_PATH}).
if($ENV{ESP_IDF_PATH}) was not evaluating to true as it should have
when env[ESP_IDF_PATH] was set.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Use the existing J-Link functionality to support debugging nRF5x targets
with GDB over a Segger J-Link USB connection.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
ST official reference for this board is B-L475E-IOT01A.
While not used in zephyr, add reference in documentaion title.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The build documentation for this board is misleading. It says to "set
JAILHOUSE_QEMU_IMG_FILE", *then* run cmake commands. But setting the
variable must be part of the cmake commands themselves. Fix it.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Enable DT support in the dfu-util flasher when the target is a
DfuSe (DFU + ST extensions) device.
Untangling DfuSe-specific options (currently, the default is 'leave',
to immediately start running after the flashing is done) from the
actual address makes this cleaner, and sets up a subsequent patch to
let callers set DfuSe options.
It also lets us fix an unnecessary printline when flashing DfuSe
devices. There's no need to reset those, since the 'leave' modifier
starts execution immediately.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The various runners (flash/debug scripts) use environment variables to
take arguments. This is legacy behavior which is not desirable.
Use command line arguments instead.
Note: this leaves more general environment variables with publicly
documented behavior in place for now, for compatibility, e.g.:
ZEPHYR_FLASH_OVER_DFU, OPENSDA_FW, ESP_IDF_PATH, PYOCD_DAPARG
For example, when using dfu-util to flash arduino_101, instead of
setting DFUUTIL_PID, DFUUTIL_ALT, and DFUUTIL_IMG environment
variables, have the script invocation look like this:
python3 .../zephyr_flash_debug.py dfu-util flash \
[common arguments omitted] \
--pid=8087:0aba --alt=x86_app \
--img=.../build/zephyr/zephyr.bin
Make similar changes for other runners (openocd, etc.) and
targets (debug, debugserver).
To implement this in the scripts:
- have the individual scripts/support/runner/some-runner.py files
register their own command line arguments
- teach them to construct instances from arguments, not the
environment
- have zephyr_flash_debug.py request runners to register command
line argument parsers, and handle arguments
In the build system:
- add a new board_runner_args() extension function that board.cmake
files can use to add to the zephyr_flash_debug.py command line
- adjust cmake/flash/CMakeLists.txt to invoke with arguments
- add new helper include files for each runner (like
boards/common/dfu-util.board.cmake, etc.), which add default
options as needed and then add on overrides from
board_runner_args() calls
- update board.cmake files to use the new includes and extension
This implied some tweaking when using openocd to make the CMake string
escaping and unescaping work properly.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The Python-based runners have replaced the old shell scripts. Refactor
the build system accordingly:
- FLASH_SCRIPT is now BOARD_FLASH_RUNNER
- DEBUG_SCRIPT is now BOARD_DEBUG_RUNNER
The values, rather than being the names of files, are now the names of
runners in scripts/support/runner. They are still short, descriptive
names like "openocd", "jlink", "em-starterkit", etc.
Adjust the zephyr_flash_debug.py call and runner internals
accordingly. Have each runner class report a name and the commands it
can handle. This lets us move some boilerplate from each do_run()
method into the common run() routine, and enables further improvements
in future patches.
The handles_command() method is temporary, and will be replaced by a
more general mechanism for describing runner capabilities in a
subsequent patch. The initial use case for extending this is to add
device tree awareness to the runners.
To try to avoid user confusion, abort the configuration if an
xxx_SCRIPT is defined.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
To avoid configuration surprises, replace
CONFIG_CLOCK_STM32_PLL_SRC_HSI
with
CONFIG_CLOCK_STM32_PLL_SRC_HSI=y
No impact today, but could depend on tools.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
During cmake migration the load image was not correctly set.
This was causing flash failures.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
For a lot of scenarios the isr stack was no longer enough.
Hence increased the stack size.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
As em7d is supported, all configurations of em_starter_kit version 2.3
are supported. Update all the defconfig to version 2.3.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* em7d of em_starterkit 2.3 supports secure mode. add the support
in kconfig and build system.
* change the default configuration of em_starterkit 2.3 to em7d
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
On stm32f3_disco pins PF0/PF1 are used for OSC_IN/OSC_OUT
signals. Use pins PA9/PA10 for I2C_2 port
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Enable USB OTG support for olimex stm32-e407 and stm32f407g_disc1
boards by adding USB OTG to the pinmux table. Also, fix out of
range endpoint addresses in CDC ACM case for STM32F4 based boards.
Signed-off-by: Sudarsana Nagineni <sudarsana.nagineni@intel.com>
'make flash' is failing for altera_max10 board due to the
missing NIOS2_CPU_SOF environment variable. Though it is set
in arch/nios2/soc/nios2f-zephyr/CMakeLists.txt but it is not
taking effect when flashing script is run. The reason could be
following which is mentioned in https://itk.org/Wiki/CMake_FAQ
"environment variables SET in the CMakeLists.txt only
take effect for cmake itself (configure-time), so you cannot use
this method to set an environment variable that a custom command
might need (build-time)."
Now, NIOS2_CPU_SOF is set from boards/nios2/altera_max10/board.cmake
file which is more logical because all the FLASH related environment
variables are being set from board.cmake
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
This is needed by platforms like jailhouse.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Signed-off-by: Gustavo Lima Chaves <gustavo.lima.chaves@intel.com>
We don't want to pollute core-infrastructure with board-specific code,
so we move the qemu discovery to after board.cmake has been executed,
and we introduce the overridable QEMU_binary_suffix CMake variable.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
"-serial mon:stdio" was already injected elsewhere, so remove
duplication. That argument, when coming from the common infrastructure,
also comes as one of the last ones. Because of that, the former "-serial
vc" was taking precedence and we were never seeing output on stdio.
Removing the virtual console altogether, for now, fixes that.
Finally, since cmake came in, we have to fix the path for the fsdev
argument to QEMU as well.
Signed-off-by: Gustavo Lima Chaves <gustavo.lima.chaves@intel.com>
This board doesn't support the 'flash' goal, which was mistakenly
included during the CMake conversion.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Footnote reference in a code block is ignored. This text shouldn't
really be in a code block anyway, so just make it a paragraph with a
trailing footnote reference.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
External serial flash on this board is 4MB.
Previously, this was confused with internal flash, which is 1MB.
Fixes#1270
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The following files didn't have any copyright or license headers on them
when they got contributed. So add the SPDX Apache license and
appropriate copyright info:
boards/arm/stm32l476g_disco/pinmux.c
samples/basic/threads/src/main.c
tests/net/socket/tcp/src/main.c
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added Inter-IC Sound driver (based on SSC module) for Atmel
SAM MCU family.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-2509
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Getting warnings from Kconfig after generalising how CPU_HAS_FPU is
configured on the architecture level. 2 Boards were settings this value
in the wrong place.
Fixes#5211.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The jailhouse board's build is currently broken.
It wants to depend on the qemu board's devicetree, but can no longer
do so since the board-level dts files were moved into individual board
directories.
To restore the build, insert the qemu_x86.dts contents into
x86_jailhouse.dts.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The kernel timer frequency was incorrectly set to the system clock
frequency (528 MHz) instead of the core clock frequency (600 MHz).
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Not all boards require the various binary formats zephyr generates. So
be selective based on the arch, SoC or board and only geenrate the
binaries actually needed.
Fixes#5009
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
As flash address changes between different boards of same Soc,
it is derived from .dts file instead of hard coding in .dtsi.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Add configuration, pinmux, dts and documentation for the STM32L476G
Discovery board based on the STM32L476VG SoC.
Signed-off-by: Arthur SFEZ <arthur.sfez@gmail.com>
Delete the native timer soft IP driver as we will be reusing
the Altera's HAL drivers for most of the soft IP's.
Add shim driver support for Altera timer system clock soft IP.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
patch removes the mem.h and marcos used in that file are
moved appropriate board files. As there are boards with
different flash configuration but of same soc, flash and
ram size are moved to dts file instead of dtsi
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
The '=' character was incorrectly getting passed to the JLinkGDBServer
device argument, and caused the server to fail to connect to the target.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Rename the Atmel SAM I2C driver based on TWIHS module to match the
convention:
<driver class>_<SoC family>_<hardware module used by the driver>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
olimexino_stm32 was not getting the flash base address from the Kconfig
variable. Since the board uses DTS that will get set, so we can use the
standard openocd.board.cmake.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Unlike other NXP SoCs currently in Zephyr, the mimxrt1052 has the ARM
MPU rather than the NXP MPU. Start out by enabling it with a simple set
of memory regions for "flash" (ITCM), "ram" (DTCM), and the peripheral
buses. More regions will need to be added when we implement support for
external memories.
Tested with:
- samples/mpu/mpu_stack_guard_test
- tests/kernel/mem_protect/protection
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds support for the NXP MIMXRT1050-EVK board, an entry-level
development board for the new mimxrt1052 Cortex-M7 SoC.
Adds pinmuxing, dts, documentation, and jlink debug support for the new
board. Note that pinmuxing uses the mcux pinmux driver directly rather
than the Zephyr pinmux interface. The mimxrt1052 SoC has complicated
pinmuxing that may require changing the Zephyr pinmux interface to
support, so for now let's use the mcux driver directly.
We are also not yet configuring the external flash, therefore a debugger
is required to load code to the internal sram. The on-board OpenSDA
circuit with jlink firmware is sufficient, and the 'make debug' build
target is supported.
Samples tested include: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
the current zephyr sdk now includes openocd configurations for l4
boards, we can now update the boards and docs to reflect this
Signed-off-by: Arthur SFEZ <arthur.sfez@gmail.com>
The old way of constructing FLASH_SCRIPT_ENV_VARS was corrupting the
values that were passed to the flasher. This new method is the
standard way of creating a dictionary/hashmap in CMake and does not
suffer from the same problem.
This fixes
https://github.com/zephyrproject-rtos/zephyr/issues/4844#event-1334599401
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the dts fixup files into the board dir so that board ports can be
more standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
The port will enable Zephyr to run as a guest OS on x86-64 systems. It
comes with a test on QEMU to validate that, thus this new board
introduction. It's "make run" target will issue QEMU with the same
configuration Jailhouse upstream uses for their confis/qemu-x86.c root
cell configuration:
Test configuration for QEMU Q35 VM, 1 GB RAM, 4 cores,
6 MB hypervisor, 60 MB inmates (-4K shared mem device)
This will work provided qemu-system-x86_64 is installed in the system
and a given (qcow2) image with the Jailhouse root cell in it is
provided (any of those will ever ship with Zephyr, it's out of its
scope).
Signed-off-by: Gustavo Lima Chaves <gustavo.lima.chaves@intel.com>
Due to copy paste issue, doc file for board nucleo_f030r8
had wrong file name.
Fix it with correct doc name
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
I2C_1 is enabled in board's DT file but we need to enable
it also in boards default config.
I2C_0 doesn't exist in STM32L475 SOC.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Provide default settings in disco_l475_iot board for following
sensors: LSM6DSL, LIS3MDL, LPS22HB, HTS221.
Sensors are disabled by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This should clear up some of the confusion with random number
generators and drivers that obtain entropy from the hardware. Also,
many hardware number generators have limited bandwidth, so it's natural
for their output to be only used for seeding a random number generator.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Add board configuration, dts and pinmux, based on
arm/stm32f4_disco and arm/nucleo_f411re boards.
Error free tests are executed on eval board with the following
sample applications:
- hello_world
- blinky-sample
- button-sample
- console_echo_sample
- console_getchar_sample
Signed-off-by: Jose F. Fernandez <jffernandez@fenix-es.com>
Replacing the default paging scheme from 32-bit paging to
PAE paging in QEMU.
JIRA:ZEP-2511
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
We shouldn't select BOARD_DEPRECATED but set a string with the release
version that the board will get removed in.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replacing the default paging scheme from 32-bit paging to
PAE paging in QEMU.
JIRA:ZEP-2511
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Page Address Extension(PAE) page tables make use of NXE bit in
EFER register.
This patch enables the capability needed to set this bit.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
nucleo_f030r8 fails in CI because applications need
more RAM.
Reduce kernel memory used by stacks and ISR vector table.
Fixes#3923
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The original developer no longer has a working board and isn't
interested in maintaining support for the board. Mark the board
deprecated for now and see if anyone wants to pick it up, otherwise will
remove it in a future release.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Match change we made to how I2C is enabled for other stm32 platforms:
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The IAMCU variant does not need to be the default, this calling
convention was to support the discontinued Quark platforms.
qemu_x86 and qemu_x86_nommu now are set as default.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This will run all tests with the memory management unit disabled.
This means no hardware-based stack protection or user threads.
qemu_x86_iamcu now runs with all MMU features enabled.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This patch adds support for TI Simplelink MSP-EXP432P401R-LAUNCHXL
development board based on Cortex M4 family
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Set Vendor and Product ID originally present in the firmware.
Implemented USB function is the same: CDC ACM serial port.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Clean up & rework JTAG documentation for ESP-32 boards to provide full
commands and clarify gotchas.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This requires openocd version 0.10 or later.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@linaro.org>
The EFM32 Wonder Gecko Starter Kit contains sensors and
peripherals demonstarting the usage of the EFM32WG MCU
family. This patch add basic support for this board.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Supports both master and slave mode, standard and fast modes,
configurable timeouts, and a few other tunable settings.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
ESP-IDF is in constant development and it's likely that files Zephyr
depends on will be moved, removed, or renamed. Make a note that an
older version of ESP-IDF should be used instead.
Closes#1538.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Instead of having a board-specific config for this adc test, enable the
required battery-sense circuit by default at the board level when the
adc driver is enabled.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Some our Zephyr tools don't like seeing UTF-8 characters, as reported in
issue #4131) so a quick scan and replace for UTF-8 characters in .rst,
.h, and Kconfig files using "file --mime-encoding" (excluding the /ext
folders) finds these files to tweak.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Move all QEMU related defines to the boards and cleanup xtensa platforms
which were marked to be QEMU capable by mistake.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
xtensa uses more stack than other arches, enable the sentinel since we
don't currently have HW-assisted stack checking on this arch.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Default configuration for USART1 (Console output) on board
stm32f3_disco was set on PA9/PA10, which matches Rev-A/B
configuration. Though, on more recent configuration of the
board (Rev-C onward). USART1 is mapped to PC4/PC5.
This configuration has the benefit to support VCP, hence it
is chosen to be set by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable BlueNRJ chip on disco_l475_iot1 board.
Communication with SoC, is done over SPI(3). Hence this
commit enables SPI3 on SoC and configure BT_SPI IRQ,
RESET and CS pins.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add board configuration, dts and pinmux based on both
stm32f469i_disco board and nucleo_f412zg board
Signed-off-by: Massimiliano Cialdi <massimiliano.cialdi@powersoft.it>
Move all STM32 based board pinmux files into the board dirs so we are
consistent across all the STM32 platforms/boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added some clarification on flashing instructions for CC3220SF, in
support of customer issue.
Jira: ZEP-2581
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The zedboard_pulpino has a small amount of flash so we should have that
in the yaml for any tests thats might filter on code size footprint.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
patch add device tree support for develoement board of
quark_se_c1000. Previously pushed patch was flashing binary
at wrong address because of which UART was not working
Jira:ZEP-2459
test
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
BLE is the only networking interface on 96b_carbon, so if
CONFIG_NETWORKING is set, automatically use 6lowpan/BLE link
layer. This will allow to make networking apps work "out of the
box" on 96b_carbon, similar to e.g. qemu_x86 (which automatically
uses SLIP) or frdm_k64f (which automatically uses Ethernet).
This also enables NET_L2_BT_ZEP1656, because most 6LoWPAN/BLE samples
in Zephyr currently use that option, and it is required to achieve
working 6LoWPAN/BLE with Linux kernels currently widely accessible
to the end users. E.g. the latest Ubuntu LTS release, 16.04, ships
with 4.4 kernel, and can be upgraded with a special effort to HWE
kernel which is currently at 4.10. NET_L2_BT_ZEP1656 is needed for
both these kernels.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This reverts commit e1382cc7d6.
Due to restrictive simplelink host driver source licensing.
This also reverts commits based on the simplelink wifi host
driver:
Revert "ext: simplelink: host driver: depend on multithreading"
commit: 4d912b004b
Revert "ext: simplelink: Enable SimpleLink to use Zephyr __errno"
commit: 4e022f7b28
Revert "ext: simplelink: Add SimpleLink DPL porting layer to Zephyr"
commit: 4bc51e67d4
Revert "ext: simplelink: Enable build of the SimpleLink host driver."
commit: 2d2615a49a
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
* add arc mpu driver
* modify the corresponding kconfig and kbuild
* currently only em_starterkit 2.2's em7d configuration
has mpu feature (mpu version 2)
* as the minimum region size of arc mpu version 2 is 2048 bytes and
region size should be power of 2, the stack size of threads
(including main thread and idle thread) should be at least
2048 bytes and power of 2
* for mpu stack guard feature, a stack guard region of 2048 bytes
is generated. This brings more memory footprint
* For arc mpu version 3, the minimum region size is 32 bytes.
* the codes are tested by the mpu_stack_guard_test and stackprot
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add cross-referenced information on the 96b_carbon and
96b_carbon_nrf51 pages which disambiguates between the two "boards".
Also describe how to flash 96b_carbon_nrf51 with
samples/bluetooth/hci_spi and 96b_carbon with samples/bluetooth/ipsp
to support a Bluetooth HCI stack on 96Boards Carbon (the physical
board).
While we're here, make the documentation page for 96b_carbon match the
format in doc/templates/board.tmpl.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
On 96Boards Carbon, Bluetooth is provided by a secondary nRF51 chip
connected to SPI_1, so enable this peripheral and its driver when BT
is selected.
Similarly, provide BT_SPI_* configs to integrate with the BT HCI SPI
driver. The files these config values apply to only get built when
CONFIG_BT=y, but this configuration can't be handled in the "if BT"
section in 96b_carbon's Kconfig.defconfig. This is because BT_SPI is
a choice value, and thus doesn't support a default setting.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Per ZEP-1958, Phase 2 of adding CC3220sf LaunchXL support,
was to "deprecate the CC3200 launchxl support in Zephyr
(redundant to the CC3220)."
Effectively, the CC3220 SOC replaces the CC3200.
This patch removes the following:
* the imported CC3200 SDK
* CC3200 SOC, board, DTS files.
* adjusts other files where cc3200 was mentioned.
Also, it fixes explicit references to CC3200 in generic
CC32xx driver files.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Rename the BT_CONTROLLER prefix used in all of the Kconfig variables
related to the Bluetooth controller to BT_CTLR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Some boards had HAS_DTS in the defconfig which is dropped if the Kconfig
variable does not have a prompt.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The SimpleLink host driver comes with its own definition of
__errno, which conflicts with Zephyr's definition, but has
a mechanism to enable use of the porting OS's __errno variable.
This patch enables SimpleLink to use Zephyr's __errno
via the DPL porting layer.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
This patch enables and builds the SimpleLink host driver
for Zephyr introduced in a previous patch.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The ESP-WROOM-32 board exits the bootloader at 40 MHz, not 160 MHz as
suggested by documentation. The CCOUNT special register works as
advertised, but not at the expected rate. This was verified by
timestamping (at the host) the output of a dependency-free loop that
looks like:
int key = irq_lock();
while(1) {
u32_t i, count;
volatile int dummy;
for(i = 0; i < 5000000; i++) {
dummy++;
}
__asm__ volatile ("rsr.ccount %0" : "=a"(count));
printk("%d\n", count);
}
The SoC has a fairly robust set of possible CPU clocking modes, but we
don't have a driver for that yet. Until we do, set the single
configured CPU frequency to the one we get at runtime.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Now that we have an mcux shim driver, remove the old k64-specific
driver. Also remove include/drivers/k20_sim.h, since the old
k64-specific driver was the only thing left using it.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
If the ftm driver is enabled, use an instance routed to the Arduino
header and configure the pinmux accordingly. Unlike the hexiwear_k64,
the pins routed to the RGB led cannot be muxed as ftm channels.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
If the ftm driver is enabled, use the instance routed to the RGB led and
configure the pinmuxes as ftm channels instead of gpios.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The Xtensa port was the only one remaining to be converted to the new
way of connecting interrupts in Zephyr. Some things are still
unconverted, mainly the exception table, and this will be performed
another time.
Of note: _irq_priority_set() isn't called on _ARCH_IRQ_CONNECT(), since
IRQs can't change priority on Xtensa: while the architecture has the
concept of interrupt priority levels, each line has a fixed level and
can't be changed.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The random number generator from ESP32 uses noise from Wi-Fi and
Bluetooth radios. If these are off, a pseudo-random number is
generated instead; this is currently the case, but even though it's a
black box, it's arguably better than returning a timestamp as a
pseudo-random number generator.
According to the ESP32 Technical Reference manual, the RNG passed the
Dieharder Random Number Test suite (version 3.31.1)[1], but nothing has
been said about the quality of the PRNG.
The RNG register is read directly; no effort is made to use its
contents to feed an entropy pool in a way that's similar to /dev/random
on POSIX systems, as no such subsystem exists on Zephyr at the moment.
[1] http://webhome.phy.duke.edu/~rgb/General/dieharder.php
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This provides basic GPIO support, with interrupts, and the ability to
read and write to ports on a pin-by-pin basis.
Jira: ZEP-2286
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This implements a driver for the pin multiplexer as present in the ESP32
SoCs.
All APIs are supported.
Jira: ZEP-2297
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
- board name olimex_stm32_p405
- CPU STM32F405RGT6 Cortex M4
- LED/BUTTON support
- Console on USART2 with 8n1 115200 baud
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
ReST defines interpreted text roles where text enclosed by single quotes
can be "intrepreted", for example :ref:`some name` becomes a link to
a label anywhere in the doc set named "some name", :c:func:`funcname()`
becomes a link to the API documentation for "funcname", and
:option:`CONFIG_NAME` becomes a link to, in our case, the documentation
for the generated Kconfig option.
This patch fixes uses of `some name` (without a role) by either adding
an explicit role, or changing to ``some name``, which indicates inline
code block formatting (most likely what was intended).
This is a precursor to changing the default behavior of interpreted
text to treat `some name` as :any:`some name` (as configured in
doc/conf.py), which would attempt to create a link to any available
definition of "some name".
We may not change this default role behavior, but it becomes an option
after the fixes in this patch. In any case, this patch fixes incorrect
uses of single-quoted text (possibly introduced because GitHub's
markdown language uses single-quoted text for inline code formatting).
Jira: ZEP-2414
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This change fixes the prescaler values in the defconfig. The prescaler
values shown in the technical reference manual (STM32F407xx, p.19)
differ from those in the defconfig which results in wrong timer delays.
This patch corrects those values according to the manual. I tested it by
toggling a GPIO pin with different timer frequencies and run the
sanitycheck.
Signed-off-by: Andreas Kölbl <andreas.koelbl@st.oth-regensburg.de>
The previously used default value of 4 for the PPL_Q_DIVISOR results
in a frequency of 84MHz which is outside the acceptable range
of 47.88MHz to 48.12MHz.
The new value of 7 results in exactly 48MHz.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
The default boolean setting for QEMU_TARGET was incorrectly placed in
the prompt field, so it was showing up as a config option in 'make
menuconfig' when it should be hidden.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The documentation details how to install and configure all the
pre-requisites to build Zephyr for the ESP32 SoC, including using the
vendor SDK and toolchain, the flashing tool, and how to use JTAG.
Jira: ZEP-2109
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This will allow checking if we are building for QEMU globally, without
having to know the exact architecture and board name.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Now that we generate BLUETOOTH_UART_ON_DEV_NAME, UART_PIPE_ON_DEV_NAME,
and BLUETOOTH_MONITOR_ON_DEV_NAME Kconfig defines for dts enabled
platforms add those into the appropriate dts files and remove from the
various board/Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since HAS_DTS is always defined for arduino_101 the board specific
Kconfig bits associated with !HAS_DTS are never used, so lets remove
them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch fix problems in nrf52_vbluno52 document:
+ Delete `Segger RTT` from supported features
+ Add `5.0` version to Bluetooth Low Energy feature
Signed-off-by: Nam Do <robotden@gmail.com>
This will cause sanitycheck runs to finish more quickly
instead of sitting there waiting on a timeout. We already
do this with the Xtensa simulator.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Sets the default to jlink since the flashing and debugging examples
in the board document were written to use jlink.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Sets the default to daplink since the flashing and debugging examples in
the board document were written to use pyocd.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Sets the default to daplink since the flashing and debugging examples in
the board document were written to use pyocd.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Sets the default to daplink since the flashing and debugging examples in
the board document were written to use pyocd.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds the pyocd target name for the frdm_kw41z board, but does not change
the default flash/debug scripts from jlink to pyocd. pyocd has not yet
tagged a release with kw41z support, so to use it one must build pyocd
from source based on the current master branch (f21d43d).
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update the MCUX I2C driver and related platforms to get their I2C
information from the device tree. We also updated a few of the sensor
drivers found on the FRDM & Hexiwear boards to get their I2C bus name
from the device tree instead of directly from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables a usable adc driver instance based on the board design. No
additional pinmux configuration is necessary because a dedicated adc pin
is routed to the board's battery sense circuit. Updates the board
documentation to reflect that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables a usable adc driver instance based on the board design and
configures the pinmux to enable the SoC's PTB1 pin, which is routed to
the board's battery sense circuit. Updates the board documentation to
reflect that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables a usable adc driver instance based on the board design and
configures the pinmux to enable the SoC's PTB10 pin, which is routed to
the Arduino header A2 pin. Updates the board documentation to reflect
that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables a usable adc driver instance based on the board design and
configures the pinmux to enable one adc channel on the SoC's PTB2 pin,
which is routed to the Arduino header A2 pin. Updates the board
documentation to reflect that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables a usable adc driver instance based on the board design and
configures the pinmux to enable one adc channel on the SoC's PTB2 pin,
which is routed to the Arduino header A2 pin. Updates the board
documentation to reflect that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
patch uses chosen property zephyr,bt-uart, zephyr,uart-pipe
and zephyr,bt-mon-uart to determine the uart instance to be
used for bluetooth,uart_pipe and bluetooth_monitor and generate
appropriate configs.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
+ The VBLUno52 board
nRF52832 ARM Cortex-M4F processor
Bluetooth Low Energy 5.0
DAPLink interface
UNO pinout
4 power
+ The following samples were tested:
hello_world
basic/button
basic/blinky
bluetooth/peripheral_hr
bluetooth/beacon
Signed-off-by: Nam Do <robotden@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We can use the chosen property "zephyr,console" to determine what uart
should be used as the console and find its name to generate a define for
CONFIG_UART_CONSOLE_ON_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch add I2C to supported features and I2C section for
96b_carbon, nucleof401re and olimexino_stm32
It also adds serial port section to 96b_carbon and olimexino_stm32
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
We have lots of RAM, this helps catch bugs.
Enable XIP as well, this used to be turned on but was
shut off for some reason.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Previously we were instantiating QEMU with 32MB of RAM but
only enabling a small fraction of it.
Now we boot with 8MB of ram. We ignore the first 4K so we can
make that an unmapped paged to catch NULL pointer dereferences.
If XIP is enabled, the "ROM" region will be the first half of
memory, the "RAM" region the latter.
Move the IDT_LIST and MMU_LIST regions elsewhere so they don't
overlap the new memory arrangement.
Use !XIP to fix a problem where CONFIG_RAM_SIZE was set incorrectly
for XIP case.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Configure I2C using DT for the following STM32 boards:
disco_l475_iot1
nucleo_f401re
96b_carbon
olimexino_stm32
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The stm32f3_disco has 40k of ram and we have some tests that require
more than that so we need to specify it in the yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This should be a default option for this board which would allow us to
remove it from many sample configurations that can be then used for
other boards.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
+ VBLUno51 board
nRF51822
Bluetooth Low Energy
DAPLink interface
UNO pinout
4 power
+ Wiki: https://vngiotlab.github.io/vbluno/
+ The following samples were tested:
hello_world
basic/button
basic/blinky
bluetooth/peripheral_hr
bluetooth/beacon
Signed-off-by: Nam Do <robotden@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Sidebar navigation for supported boards is wonky: opens to show
all boards (making for lots of scrolling to see the sidebar) and
sidebar items aren't always clickable (as explained in the JIRA
issue).
Fix is to not use multiple toctree directives in boards.rst and
create intermediate architecture-specific supported board docs.
JIRA: INF-132
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Board port was done before the yaml transition, so was missing a
cc2650_sensortag.yaml. As such when we build all the test we get a few
build errors that we also fixed up.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add configuration, documentation, pinmux, fixup and dts support for
STM32F103x8 based Minimum System Development board.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Allow to use an external debug adapter such as J-Link or ULINK
connected to a 20-pin JTAG header to flash the image. SWD is
the actual protocol used by the debug interface.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
As there are multiple ways to flash or debug (pyOCD or openOCD) allow
the user to override the default.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
patch adds necessary files and does the modification
to the existing files to add device support for
arduino_101 board.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Add board metadata to be consumed by the sanitycheck script to provide
better matching with testcases and to test based on features declated in
the board files.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This flashes Zephyr at 0x1000: that's where the first stage bootloader,
part of the ESP32 ROM, expects to find an "image header".
The second-stage bootloader, part of ESP-IDF, isn't used by the Zephyr
port. However, the bootloader can be used if desired; please refer to
the ESP-IDF documentation on how to set up partitions tables and use
the bootloader.
The following environment variables will affect the ESP32 flashing
process:
Variable Default value
ESP_DEVICE /dev/ttyUSB0
ESP_BAUD_RATE 921600
ESP_FLASH_SIZE detect
ESP_FLASH_FREQ 40m
ESP_FLASH_MODE dio
ESP_TOOL espidf
It's impossible to determine which serial port the ESP32 board is
connected to, as it uses a generic RS232-USB converter. The default of
/dev/ttyUSB0 is provided as that's often the assigned name on a Linux
machine without any other such converters.
The baud rate of 921600bps is recommended. If experiencing issues when
flashing, try halving the value a few times (460800, 230400, 115200,
etc). It might be necessary to change the flash frequency or the flash
mode; please refer to the esptool documentation for guidance on these
settings.
If ${ESP_TOOL} is set to "espidf", the esptool.py script found within
ESP-IDF will be used. Otherwise, this variable is handled as a path to
the tool.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The first stage bootloader, part of the ESP32 ROM, already sets up
a stack that's sufficient to execute C programs. So, instead of
implementing __stack() in assembly, do it in C to simplify things
slightly.
This ESP32-specific initialization will perform the following:
- Disable the watchdog timer that's enabled by the bootloader
- Move exception handlers to IRAM
- Disable normal interrupts
- Disable the second CPU
- Zero out the BSS segment
Things that might be performed in the future include setting up the
CPU frequency, memory protection regions, and enabling the flash
cache.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Unconditionally use CONFIG_SIMULATOR_XTENSA to determine if XT_SIMULATOR
or XT_BOARD should be defined.
If CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC, also define XT_CLOCK_FREQ. This
isn't ideal as the clock frequency might be changed in runtime and this
effectively makes it a constant.
Until we can control the clock frequency in runtime, this will suffice.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This is a minimal driver enabling console output during the port
bringup. While the driver works, only one of the three UART devices
are supported, and there isn't any way to change any parameters or
use interrupts. This will most likely be superceded by a proper
driver after the port has matured.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
A couple of docs were created in previous PRs with board support
information common to a few boards. Move these to a new section
for "Board Support Tools". (I debated about hiding them completely
but decided it would still be useful to have these tool docs appear
in the table of contents, just not embedded with the supported boards
docs.)
Moved these board tools docs over to the doc/ folder and out of
boards/ and removed these pages from the navigation index.
JIRA: ZEP-2285
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
- board name olimex_stm32_e407
- CPU STM32F407ZGT6 Cortex M4
- LED/BUTTON support
- Console on USART1 with 8n1 115200 baud
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Some files have moved from their original location, or are no longer
available. For the mbedtls samples, tweak the link to point to a page
where links for current and previous downloads can be found.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Board documentaion for altera_max10 referenced the nios2-configure-sof
tool in arch/nios2/soc/nios2f-zephyr/cpu/ when this tool is actually
part of the Altera Quartus SDK (the .sof FPGA configuration files are
in this folder)
jira: ZEP-2006
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The wiki directions indicate that this script should be used,
and openocd.sh doesn't even work. Switch to pyocd.sh by default.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add necessary board files, pinmux and device tree in order to have a
usable debug console.
Origin: Original
Change-Id: I43a9d278c3f2c936a714263626722f630367b663
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Following migration of stm32f1xx series clock control driver to
STM32Cube LL API, cleanup stm32 code base in order to take into
account that this is the only clock driver available for stm32
family.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following introduction of stm32cube LL based clock control driver
for stm32f1 series, update stm32f1xx based boards to support new
driver settings
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable the MPU on the Nucleo STM32F413 board.
Change-Id: I0f256a4c7231f9d3844e67a94d989c8d93b60e58
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
CONFIG_CLOCK_VDD_VOLTAGE does not exist. It was introduced by accident
with commit 614db02cc6 ("stm32f4: Add STM32F413 Nucleo board"), so
remove it!
Change-Id: I3363a92627708bf5ffb080c2238fc84c71caa8d9
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Atmel SAM3X series has been recently converted to use ASF
and should now use common SAM family drivers. The atmel_sam3
serial driver will be removed in the future.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Increase to 1024 to get more tests and sample running on this device
with only 8K of SRAM.
Change thread stack size in the mslab test to make it fit into this
board.
Jira: ZEP-2079
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
We now have generic ARM M4 MPU support added to Zephyr.
Let's enable it for use with Nordic nRF52 chips.
Memory Layout was generated from Section 8.3 "Memory
Map" of nRF52 Product Specifications (for both nRF52832
and nRF52840):
0x00000000: Flash
0x10000000: Factory Information Config Registers
0x10001000: User Information Config Registers
0x20000000: SRAM
0x40000000: APB Peripherals
0x50000000: AHB Peripherals
0xE0000000: ARM M4 Private Peripheral Registers
NOT Configured:
0x60000000: External RAM
0x80000000: External RAM
0xA0000000: External Device
0xC0000000: External Device
NOTE: More work will be needed for future Nordic MWU (Memory
Watching Unit) support.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Neither ASF nor CMSIS provide defines that can be processed by
the assembler. Exclude those from soc.h. Before this was done
incorrectly in board.h file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Removed CONFIG_HAS_DTS from the stm32f4_disco_defconfig &
stm32l496g_disco_defconfig files as its automatically selected for all
ARM SoCs at this point.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We now get the baud rate for the serial port from the device tree so we
don't need to be setting it in the defconfig.
The baud rate changed from 38400 to 115200 when we introduced the device
tree for MPS2. The default baud rate was based on matching mbed, but we
use 115200 to match the standard default we have for most boards now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch converts Atmel sam3x MCU series to use register
header files from Atmel Software Framework (ASF) library.
By using ASF different Atmel SAM MCU series can use common
device drivers.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Now that NXP boards support 'make flash' and 'make debug' via pyOCD and
Segger J-Link, update all the NXP board docs accordingly. Adds a new
generalized OpenSDA document so certain details don't have to be
repeated for every OpenSDA board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add configuration, pinmux, dts and documentation for the STM32L496G
Discovery board based on the STM32L496AG SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Since we now select HAS_DTS from the cortex-m Kconfig we don't need it
in 96b_carbon_nrf51_defconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* Change emsk to EM Starter Kit
* Fix some typos
* Add more statement for steps of using EM Starter Kit
Signed-off-by: Huaqi Fang <huaqi.fang@synopsys.com>
Due to support updated from 2.2 to 2.3, a debug script is provided
for emsk, so developer can directly debug the zephyr application
using commands such as follows.
+ make BOARD=em_starterkit debug
Signed-off-by: Huaqi Fang <huaqi.fang@synopsys.com>
Here are the main changes:
* board: Update EMSK onboard resources such as Button, Switch and LEDs
+ update soc.h for em7d, em9d, em11d
+ update board.h for em_starterkit board
* arc: Add floating point support and code density support
+ add kconfig configuration
+ add compiler options
+ add register definitions, marcos, assembly codes
+ fixes in existing codes and configurations.
* arc: Update detailed board configurations for cores of emsk 2.3
* script: Provide arc_debugger.sh for debugging em_starterkit board
+ make BOARD=em_starterkit debug
This will start openocd server for emsk, and arc gdb will connect
to this debug server, user can run `continue` command if user just
want to run the application, or other commands if debugging needed.
+ make BOARD=em_starterkit debugserver
This will start an openocd debugger server for emsk, and user can
connect to this debugserver using arc gdb and do what they want to.
+ make BOARD=em_starterkit flash
This will download the zephyr application elf file to emsk,
and run it.
Signed-off-by: Huaqi Fang <huaqi.fang@synopsys.com>
Now that we can specify what toolchain is intended for each
SOC, enable some more SOCs to be built.
A full sanitycheck run will require the installation of both
RF-2016.4 and RG-2016.4 releases.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This patch adds initial MPU support to NXP K6x family.
The boot configuration prevents the following security issues:
* Prevent to read at an address that is reserved in the memory map.
* Prevent to write into the boot Flash/ROM.
* Prevent from running code located in SRAM.
This driver has been tested on FRDM-K64F.
Change-Id: I907168fff0c6028f1c665f1d3c224cbeec31be32
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Link was pointing to wrong reference manual.
Fixed by this commit
Change-Id: I97c6748fcad27ad6f2541ed4cba6141fcbb2576a
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The xtensa simulator can in fact simulate a variety of Xtensa SOCs.
Fixes build for alternate xt-sim_* defconfigs.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The xt-sim defconfigs were selecting CONFIG_SIMULATOR_XTENSA instead
of CONFIG_BOARD_SIMULATOR_XTENSA.
Fix defconfigs and rename to CONFIG_BOARD_XT_SIM to ease any future
confusion between these similarly named defconfigs.
CONFIG_SIMULATOR_XTENSA is automatically set by xt-sim's
Kconfig.defconfig, it doesn't need to be explicitly specified in the
defconfigs themselves.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Now that all ARM platforms have a device tree we can move selecting of
HAS_DTS up and remove any !HAS_DTS cases, as well as setting in all the
defconfigs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add necessary board files, pinmux and device tree in order to have a
usable debug console.
Origin: Original
Change-Id: I280320700352fd36a544c03f4e57d2eeec2449e5
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Adds a new debug support script using pyOCD and configures most NXP
boards so they can use it. frdm_kw41z is the one exception because pyOCD
doesn't yet support kw41z. Tested with pyOCD v0.8.0 and the latest
DAPLink firmware for each board.
Introduces two new environment variables, PYOCD_FLASHTOOL and
PYOCD_GDBSERVER, that allow you to set custom paths to the pyOCD tools.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new debug support script using Segger JLink and configures all
NXP boards so they can use it. Tested with Segger JLink GDB server
V6.14b and OpenSDA v2.1 firmware.
Change-Id: Ia1b297d9c93d21db61379e22f27ae54cda3ad461
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Rename SOC_STM32L476XX to SOC_STM32L476XG to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file)
Change-Id: I834bb5b83c24c39e90c0492a2b22a7c7802de361
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The xC tag in the SoC reference indicates the flash size, use it in the
configuration to permit selection of correct flash size for dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds support for the nRF51 chip on the board.
If you'd like to run Zephyr on the STM32F4 chip on Carbon, you need to
use the 96b_carbon board instead.
The current SPI Bluetooth protocol only uses 5 wires, so we use the
remaining pin as UART TX.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This core configuration was removed from the tree since it cannot
implement irq_offload().
Remove an orphaned block in xtesna.ini.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
More general spelling fixes, and cleaning up stray UTF-8 characters
such as curly-quotes, em- and en-dashes. Use replacement strings
for |reg| and |trade|.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add configuration, dts and documentation for the Nucleo L432KC board
based on the STM32L432KC SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SimpleLink SDK actually encapsulates a family of devices,
of which cc32xx is just one device. Other devices can fit
under this SDK directory structure.
This expansion will also allow the import of the WiFi
host driver and its driver porting layer in the future,
inserted at the correct levels in the SimpleLink SDK
directory heirarchy.
Follow the URL (ending in "#directory-structure") referenced in
ext/hal/ti/simplelink/README which explains the SDK structure,
and where devices fit in.
Jira: ZEP-1958
Change-Id: I16515d3e3779de0d55d3b1b8e25029609d1f66c3
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Enable it by default now that the eth_dw driver has been ported to the
new IP stack.
Jira: ZEP-1652
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
I2C address could not be configured for HTS221.
Remove non existing configuration in disco_l475_iot1 board
Change-Id: Ib5ed8e0f770c16b124cf918bdf9ecd42cdd9b213
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The files for the Arduino Due needed to be updated to use the new
configuration when the SoC moved from the atmel_sam3 directory to
the atmel_sam/sam3x directory.
Jira: ZEP-2067
Signed-off-by: Justin Watson <jwatson5@gmail.com>
The FPGA on the MPS2 board implements 4 SBCon devices for I2C which are
connected to:
- a touchscreen controller
- the audio device (for configuration)
- both shield connectors
Change-Id: I55ca985e18b45d68f5e7421c4768dfc9bf2fcb3f
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Introduce a simple device tree for the TI lm3s6965 SoC and QEMU
Cortex-M3 board port. We get flash and memory base addresses and sizes
from the device tree as well as the ARM NVIC number of priority bits.
Change-Id: I4452b5543de7be55518997e54837ccbfd4f121df
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As disco_l475_iot1 is default board for HTS221 sample
application, provide default boards settings to get
application functional once it is delivered.
Change-Id: Ie4957538db679d076713550c1555954a6a20d3e2
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add device tree support for nRF51822 SoCs and Arduino 101-BLE,
Curie-BLE, BLE Nano, PCA10028-DK, and Quark-SE BLE boards. This
is minimal support for memory, flash, and UART.
Change-Id: I7e572bea537e384b6d66e520462f023ace0c9b35
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree support for nRF52840 SoC and PCA10056-DK board. This
is minimal support for memory, flash, and UART.
For the nRF52840 we select between "nordic,nrf-uarte", "nordic,nrf-uart"
support for each board.
Change-Id: I1c377e0cb97ff4716ea5489fffaa7c0e2b34d18a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree support for Nitrogen 96board, BLE Nano 2, and
nRF52-PCA10040 DK boards. This is minimal support for memory, flash,
and UART.
For the nRF52832 we select between "nordic,nrf-uarte", "nordic,nrf-uart"
support for each board.
Change-Id: Ia247b9b710a72416e9ab0de3ca1429bfab8917f8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit provides support for disco_l475_iot1 board
Pinmux driver is provided with initial support definitions
Change-Id: I17b637a8ba0b033014969eca8fffe76319c47c52
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to allow the use of such board, a very preliminar port was
developed. It consists of board files, as well as pinmux, uart, gpio,
spi drivers and device tree files.
Change-Id: I5753064e39e0b023cf4481744c176de26d8dbebb
Signed-off-by: Gustavo Denardin <gustavo.denardin@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commits align CONFIG_ factor names between stm32f4 and stm32l4
series to enable code factorization such as use of Q_DIVISOR.
Though, it does not concatenate kconfig sections as we might use
a bit of time to see what is needed in this regard
Change-Id: Ia603406d53949abf5675b801a5448397d5ab8462
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following activation of stm32 common clock driver for stm32f4 series
remove references to stm32f4 specific driver.
Change-Id: I372a0ea046007bcb34944d6b2b8880077583b1d3
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit provides CONFIG_ definitions to support
LL based clock driver on stm32f4 boards:
96b_carbon
nucleo_f401re
nucleo_f411re
This commit sticks to clock configurations previously defined.
Two changes to notice:
-HSE clock value should now be defined
-Prescaler values required as "1" should now be set to "1" instead
of "0".
Change-Id: I003bd226f198217d5e266e11fe37094773c1c62c
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added some review changes suggested by TI-er Bill Mills.
Jira: ZEP-1958
Change-Id: I892f22a5740ae7ae4dc949bc72de366e0e85d03c
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
This board is being replaced by the CC3220SF LaunchXL,
which has essentially the same peripheral map, 256Kb
of SRAM, but in addition has 1Mb of on-chip secure flash.
Jira: ZEP-1958
Change-Id: I80629474cab9ce41bce3903213f5c9f148cc138a
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
CC3220SF_LAUNCHXL effectively replaces the CC3200_LAUNCHXL,
with support for the CC3220SF SoC, which is an update for
the CC3200 SoC.
This is supported by the Texas Instruments CC3220 SDK.
Jira: ZEP-1958
Change-Id: I2484d3ee87b7f909c783597d95128f2b45db36f2
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Adds event based scheduling logic to the kernel. Updates
management of timeouts, timers, idling etc. based on
time tracked at events rather than periodic ticks. Provides
interfaces for timers to announce and get next timer expiry
based on kernel scheduling decisions involving time slicing
of threads, timeouts and idling. Uses wall time units instead
of ticks in all scheduling activities.
The implementation involves changes in the following areas
1. Management of time in wall units like ms/us instead of ticks
The existing implementation already had an option to configure
number of ticks in a second. The new implementation builds on
top of that feature and provides option to set the size of the
scheduling granurality to mili seconds or micro seconds. This
allows most of the current implementation to be reused. Due to
this re-use and co-existence with tick based kernel, the names
of variables may contain the word "tick". However, in the
tickless kernel implementation, it represents the currently
configured time unit, which would be be mili seconds or
micro seconds. The APIs that take time as a parameter are not
impacted and they continue to pass time in mili seconds.
2. Timers would not be programmed in periodic mode
generating ticks. Instead they would be programmed in one
shot mode to generate events at the time the kernel scheduler
needs to gain control for its scheduling activities like
timers, timeouts, time slicing, idling etc.
3. The scheduler provides interfaces that the timer drivers
use to announce elapsed time and get the next time the scheduler
needs a timer event. It is possible that the scheduler may not
need another timer event, in which case the system would wait
for a non-timer event to wake it up if it is idling.
4. New APIs are defined to be implemented by timer drivers. Also
they need to handler timer events differently. These changes
have been done in the HPET timer driver. In future other timers
that support tickles kernel should implement these APIs as well.
These APIs are to re-program the timer, update and announce
elapsed time.
5. Philosopher and timer_api applications have been enabled to
test tickless kernel. Separate configuration files are created
which define the necessary CONFIG flags. Run these apps using
following command
make pristine && make BOARD=qemu_x86 CONF_FILE=prj_tickless.conf qemu
Jira: ZEP-339 ZEP-1946 ZEP-948
Change-Id: I7d950c31bf1ff929a9066fad42c2f0559a2e5983
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Typo in :ref:`hello_world` (regular quote vs. back tick)
Change-Id: I77853f85b9c71751307ef105b6babcb0cfbc9060
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This patch adds MPU support to the ST nucleo_f411re board based on
STM32F401XE.
Change-Id: I43aae0930ccabe234fcb34216518b568a855a1be
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds MPU support to the ST nucleo_f401re board based on
STM32F401XE.
Change-Id: I5e8042c1f964827980b974a565a4d4666eeccf3b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds MPU support to the 96 boards Carbon board based on
STM32F401XE.
Change-Id: I8444318099a665133488ccdd5ba129c805f9a20e
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch enables MPU by default into the V2M Beetle port of Zephyr.
Change-Id: Iab2dea748c68a6932eb31e746d1a9cdb07808683
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
