This is needed if muxing is enabled in which case we must
change the UART to muxing UART after the AT+CMUX command
has succeed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of global workqueue, use own one so that the users of this
driver can more conveniently use global one. This means GSM modem
can work better with the UART muxing driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of using physical UART to connection to the modem, use
the GSM 07.10 muxing protocol and UART mux driver to create
virtual channels to the modem. This will allow simultaneous
PPP, AT and other type connections to the modem.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
By default PPP interface is not taken up automatically but only
after the PPP connection to modem is ready.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create support for muxed UARTs which are attached to a real
UART and which use GSM 07.10 muxing protocol to create virtual
channels that can be run on top of the real UART.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add support to GSM 07.10 muxing protocol which is used to
share the same UART for PPP and AT commands among other things.
This allows e.g., the modem to send SMS and have PPP connection
active at the same time.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fixed the ETH_SAM_GMAC_QUEUES config by adding if-statements per SoC
series.
Signed-off-by: Vincent van der Locht <vincent@vlotech.nl>
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit updates the Atmel SAM GMAC driver to select max frame size
value from the device tree. Now GMAC driver can operate with the three
different frame size options available.
The current supported values are: 1518, 1536 and 10240.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The current setup of physical layer forces RMII interface. The code was
refactored to have only one point to select proper phy interface. Now,
GMAC driver works with both RMII or MII interface. The phy connection
type is now selected by device tree. The default phy connection is RMII.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The NOCACHE_MEMORY can be enabled only for those MCU that support data
cache. The currently SoC that doesn't have data cache is SAM4E.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Improve data cache conditional build. Now data cache code is build
only if device have support to it. This enables GMAC driver for use
with devices that don't have data cache instructions.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This cleans up DMA flags by separating the necessary flags for devices
with one or multiple RX/TX queues.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The radio driver will now notify the upper layer about Frame Pending Bit
value in the ACK response it sent.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
clock-generator is a normal property. To access it we should use
DT_INST_PROP(0, clock_generator) and not DT_INST_CLOCKS_CELL().
Fixes: #24399
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Sets the "dummy data" value to send when the transmit buffer is null.
Fixes the spi_null_tx_buf test in tests/drivers/spi/spi_loopback on the
lpcxpresso54114 board.
Tested on frdm_k64f, mimxrt1050_evk, and lpcxpresso54114_m4 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
DIO handlers defined in loramac-node are quite complex. Additionally
they call read/write operations over SPI with the sx1276 chip. This
cannot work properly in interrupt context, so call DIO handlers in
system workqueue instead.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far only GPIO pin number of registered DIO line was compared with
arguments passed to GPIO callback. This is not enough when multiple gpio
controllers are used for DIO lines. As an example when DIO0 is on PA1
and DIO1 is on PB1, then DIO0 handler is called all the time.
Compare GPIO controller (in addition to pin number) of DIO lines with
the argument passed to gpio callback, so proper DIO handler is used.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This information is filled during build time from device-tree. This is
not supposed to change in runtime, so make it const.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Part of sx1276 driver which is in loramac-node module passes to Zephyr
irqHandlers with callbacks. Some of those callbacks can be NULL and this
is true now (with the current version of loramac-node) for DIO5. If we
define all 0-5 DIOs in dts, then this results in interrupts which are
unwanted. As we do not check that loramac-node callback is NULL, then we
crash trying to call it.
Check every handler during initialization and just skip initialization
of GPIO if it is NULL. This also prevents crashes, because there is no
way GPIO interrupt to be triggered in runtime for this DIO.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
The PORCTRL setting command is in 'bank2' and so might not be changed on
the controller unless bank2 is enabled first.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Make use of DT_NODELABEL macros to get device instances
information to configure drivers I2C instances.
This allows to remove I2C related lines in fixup.h files
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use compatible information to configure i2c stm32.
With this, driver version selection is done thanks to compatible
and it is not needed anymore to do this via Kconfig symbol
selection under soc/
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert the LMP90xxx ADC driver from using k_sleep() to using
k_msleep() in order to resolve a compilation error caused by passing
an int to k_sleep().
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert driver from DT_FLASH_BASE_ADDRESS and DT_FLASH_DEV_NAME to use
DT_REG_ADDR and DT_INST_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For a flash driver DT_DRV_COMPAT should be the compatible for the flash
controller and not the soc-nv-flash. Change to driver to use the flash
controllers compatible and get the soc-nv-flash properties as a child of
that controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For a flash driver DT_DRV_COMPAT should be the compatible for the flash
controller and not the soc-nv-flash. Change to driver to use the flash
controllers compatible and get the soc-nv-flash properties as a child of
that controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For a flash driver DT_DRV_COMPAT should be the compatible for the flash
controller and not the soc-nv-flash. Change to driver to use the flash
controllers compatible and get the soc-nv-flash properties as a child of
that controller.
The soc_flash_mcux supports several possible compatible so handle that
as part of how we set DT_DRV_COMPAT.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For a flash driver DT_DRV_COMPAT should be the compatible for the flash
controller and not the soc-nv-flash. Change to driver to use the flash
controllers compatible and get the soc-nv-flash properties as a child of
that controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The 32 KiBy bulk erase command was being invoked without respecting
the flag that indicates it's supported. Make the invocation
conditional.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new devicetree API. Remove per-board enabling of ADC_0 by
setting ADC_0 to default y when the 'adc' node label points at an
enabled node of the expected compatible (depending on SoC).
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Now that all entropy drivers use DTS we can remove HAS_DTS_ENTROPY being
set everywhere as well as Kconfig ENTROPY_NAME since that is now coming
from DT_ENTROPY_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the UNALIGNED_GET() macro instead of the
flash_sam0_read_unaigned_u32() function to ensure
word alignment of the source address.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
drivers: flash: sam0: fix whitespace
Fix checkpass whitespace error.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
Replace DT_I2C_._NAME macro with DT_LABEL(DT_NODELABEL()) instead. This
will allow us to remove all references to DT_I2C_._NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_I2C_._NAME macro with DT_LABEL(DT_NODELABEL()) instead. This
will allow us to remove all references to DT_I2C_._NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_I2C_._NAME macro with DT_LABEL(DT_NODELABEL()) instead. This
will allow us to remove all references to DT_I2C_._NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Updated the openisa,rv32m1_vega-pinmux binding to require the label
property and updated the rv32m1.dtsi to add label properties for the
pinmux nodes.
Also update gpio_basic_api test to use DT_NODELABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When configuring the I2S peripheral as a master, the DMA channel
direction must be configured to transfer data from memory to the
peripheral.
Currently the configuration of channel direction is always set for
peripheral to memory regardless of whether it is the TX or the RX
channel.
Signed-off-by: Abe Kohandel <abe@electronshepherds.com>
HWINFO drivers should be responsible for ensuring that
the data structure is a sequence of bytes. That is not
what the current sam0 and nordic drivers do. The drivers
read the data as u32_t and then memcpy the data to a
buffer. This ensures the data has the endianness of the
underlying MCU, which in this case is Cortex M0 which
is little endian.
This commit fixes the endianness so the data can be
interpreted as a "left to right sequence of bytes".
This commit updates the API doc to provide clarification
of the data structure.
Add to 2.3 release notes.
Fixes#23444, #24103
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
Obtain RX time from the radio driver. Fill the `net_pkt` with
a timestamp if `NET_PKT_TIMESTAMP` is enabled.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
nRF radio driver will call `nrf_802154_transmit_failed` callback in case
no ACK is received, so we do not need to set timeout at the shim layer
anymore.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Update `flash` shell commands to take an optional device argument,
instead of using the chosen flash device.
Signed-off-by: Ivo Clarysse <ivo@bcdevices.com>
Adds a shim layer around the mcux lpc flexcomm driver to adapt it to the
zephyr i2c interface. It leverages heavily from the existing mcux lpi2c
shim driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Replace DT_FLASH_DEV_BASE_ADDRESS with new DT_REG_ADDR/DT_INST macro as
we phase out DT_FLASH define usage.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_FLASH_WRITE_BLOCK_SIZE with new DT_INST_NODE_HAS_PROP and
DT_INST_PROP macro as we phase out DT_FLASH define usage.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_FLASH_DEV_BASE_ADDRESS with new DT_REG_ADDR/DT_INST macro as
we phase out DT_FLASH define usage.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of DT_FLASH_DEV_NAME with DT_INST_LABEL in drivers as we
want to phase out DT_FLASH_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When a DMA stream is successfully disabled, the function should
immediately return with a success status.
Signed-off-by: Abe Kohandel <abe@electronshepherds.com>
DT_CALL_WITH_ARG() is an internal implementation detail that should
not be used outside of devicetree.h.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The duration is used in math with the uptime clock, not as a timeout.
Correct value expression and rename to clarify units.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use valid stm32 flash driver compatibles instead of flash
area compatible.
For 'write_block_size' property, use reference to soc-nv-flash.
fixes#23997
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Create a dedicated config symbol for video device initialization.
Generally, video device init is low priority comparing to standard
devices. Moreover some video device can rely on other device init,
like the csi mcux driver which rely on sensor and i2c init.
This fixes a crash in video capture sample, when camera sensor
(mt9m114) is not connected.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Notify about actual data transmission start.
Needed when ACK timeout is disabled in the radio driver.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
When enabled, instead of erasing entire flash page at once, page will
be erased in defined time slices. Erasing single page stalls CPU
for significant time share (~80ms) and partial erase divides the
operation in to the shorter time periods, resuming CPU operation in
meantime and enabling better scheduling of time sensitive operations.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The recent change in 2.2.0 that disables the watchdog
on boot introduced a hard fault when a log message
is generated too early before even the RTC is
initialized.
This commit removes the log message.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
Add an optional weighted average filter to the ADC readings in the NXP
Kinetis temperature sensor driver as recommended in NXP AN3031.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Fix a potential 32 bit multiplication overflow (muliplying by 10000
instead of 1000000) and change the calculations and units accordingly.
Improve the code readability and traceability towards NXP AN3031 by
using the same variable name as in the application note.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
sys_clock_disable now is only called in sys_reboot.
This API is outdated, no need to implement it and
there is a weak version.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* add interrupt lock in low level API to gurantee the
correctness of operations.
* make some functions as in-line functions
* clean up and optimize the code comments
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
wifi-reset-gpios is currently ignored after conversion to DT_INST
macros. Use wifi_reset_gpios instead of reset_gpios to fix the problem.
Fixes: a464ae7163 ("drivers: wifi: esp: Convert to new DT_INST
macros")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
To ease driver configuration, enable ENTROPY_STM32_RNG
only if device node matching driver compatible is enabled.
No more need to enable config symbol under soc/
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert stm32 entropy driver to configuration based on device tree.
Select HAS_DTS_ENTROPY symbols and configure CONFIG_ENTROPY_NAME
in fixup files.
Since rng node is not enabled (or available) on all boards, it could
happen that symbol ENTROPY_STM32_RNG is not enabled and hence
ENTROPY_HAS_DRIVER not selected which ends up with a symbol
ENTROPY_NAME defined throufg Kconfig selection. Thus, in fixup file,
CONFIG_ENTROPY_NAME is defined only if not already defined.
Additionally, update boards that used to configure entropy by default.
On these boards, enable rng device in device tree and remove Kconfig
related configuration (which should not be part of default
configuration).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fixup cases of GPIO_PORT_PIN_MASK_FROM_NGPIOS(DT_INST_PROP(n, ngpios))
to use GPIO_PORT_PIN_MASK_FROM_DT_INST(n) instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
With the introduction of the new device-tree macros it is now possible
to use the settings for speed and flow-control from the bus node instead
of having the same properties on the esp node itself.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
Instead of using Kconfig options for setting the device name and IRQ
priority for the entropy_nrf5 driver, get these settings from the rng
node defined in DTS for a given SoC.
Provide also fixups for CONFIG_ENTROPY_NAME, until applications using
entropy drivers are converted to use DTS as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
We rename the nRF53 Dev Kit board target (nrf5340_dk_nrf5340)
to nrf5340pdk_nrf5340. We update all associated references
in the supportive documentation and all nRF5340-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Also update counter_basic_api test to use DT_INST and remove the
udoo_neo_full_m4.conf as its not longer needed since the per instance
Kconfig sybmols don't exist anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Additionally remove udoo_neo_full_m4.conf from gpio_basic_api test since
the Kconfig symbols don't need to be set anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
All GPIO controller drivers support DTS so we can select HAS_DTS_GPIO
at the GPIO driver subsystem level rather than for each specific driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When disabling the interrupt current implementation of the
gpio_pin_interrupt_configure function will first reconfigure the
interrupt to be active on gpio low level.
Since the pin interrupt is enabled if the gpio pin level happens
to be low at the time the interrupt will trigger immediately.
Rewrite the function to disable the interrupt in a safe manner.
Signed-off-by: Frank Li <lgl88911@163.com>
The net_buf subsystem is now fully compatible with the new timeout
API, so move the selection of the legacy API to those specific
subsystems that use net_buf and still need converting.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Delay radio abort called in the flash driver to emulate the
behavior of pre-empt timeout in Bluetooth LL split
controller. Without this, the driver aborted radio events
in its reserved time space.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
At present wdt_gecko driver supports ULFRCO as its only clock source.
Select the clock explicitly, do not rely on the default configuration
provided by the SiLabs header files. The default configuration is
changing between different SiLabs HAL versions.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Enable the gpio_sx1509b driver by default when a "semtech,sx1509b"
compatible node is enabled in devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Make I2C and SPI drivers for nRF SoCs no longer dependent on Kconfig
options that enable instances (i.e. I2C_x and SPI_x). Now these drivers
enable hardware instances when corresponding nodes in devicetree are
enabled (have status "okay").
For I2C, SPI, and UART drivers, instead of using Kconfig dependencies
to prevent enabling of hardware instances that cannot be used together
(e.g. SPIM1 and TWIM1), a file that signals invalid configurations with
build assertions is added to compilation.
Also dependencies on HAS_HW_NRF_* options are removed from Kconfigs
of I2C, SPI, and UART drivers, as for hidden options that activate
proper type of driver such dependencies are not actually helpful.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `UART_x_NRF_UART*` that select
the type of nrfx driver (for UART or UARTE peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding UART node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between UART and UARTE for a given instance.
Since all `UART_x_NRF_UART*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `I2C_x_NRF_TWI*` that select
the type of nrfx driver (for TWI or TWIM peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding I2C node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between TWI and TWIM for a given instance.
Since all `I2C_x_NRF_TWI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `SPI_x_NRF_SPI*` that select the
type of nrfx driver (for SPI, SPIM, or SPIS peripheral) to be used
for a given instance. This prevents the options from being modified
in configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding SPI node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between SPI, SPIM, and SPIS for a given instance.
Since all `SPI_x_NRF_SPI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add CSMA CA capability for the `ieee802154_nrf5` radio driver along with
appropriate implementation in the `nrf5_tx` function.
Introduce 802.15.4 radio driver with CSMA/CA support enabled. Add help
text, mentioning a list of peripherals occupied by the radio driver.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Even though radio driver can report in its capabilities that it does
support CSMA CA, there's no way in the driver to select how the frame
should be transmitted (with CSMA or without). As layers above radio
driver (Thread, Zigbee) can expect that both TX modes are available, we
need to extend the API to allow either of these modes.
This commits extends the API `tx` function with an extra parameter,
`ieee802154_tx_mode`, which informs the driver how the packet should be
transmitted. Currently, the following modes are specified:
* direct (regular tx, no cca, just how it worked so far),
* CCA before transmission,
* CSMA CA before transmission,
* delayed TX,
* delayed TX with CCA
Assume that radios that reported CSMA CA capability transmit in CSMA CA
mode by default, all others will support direct mode.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Convert driver to utilize the new DT_INST macros completely and remove
associated Kconfig symbols that now come from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The ft5336 has an interrupt that can be used instead of polling
this commit adds support for using it but as an option to maintain
compatibility. Tested on the stm32f746g_disco board.
Signed-off-by: Mark Olsson <mark@markolsson.se>
Run the int_literal_to_timeout Coccinelle script to fix places where
it is clear that an integer duration is being passed where a timeout
value is required.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use device node declaration instead.
Clean up GPIO_STM32_PORT* Kconfig symbols.
On some boards some gpio ports where disabled using Kconfig symbols.
Disable them now via device tree nodes in boards dts files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move towards use DTS for driver instance name instead of Kconfig sybmol.
This is towards phasing out CONFIG_ENTROPY_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Commit 7832738ae9 ("kernel/timeout: Make timeout arguments an opaque
type") changed the forever value for timer drivers to K_TICKS_FOREVER
from K_FOREVER.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add a YAML, DTS node and driver support to utilize data from devicetree
for register address and driver name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Energy scan procedure, while introduced specifically for OpenThread in
Zephyr, may also be used by other upper layers (like Zigbee).
Therefore, disable conditional inclusion of the `ed_scan` API.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Convert drivers that have the following pattern:
#if DT_INST_NODE_HAS_PROP(0, label)
INIT_MACRO(0)
#endif
...
#if DT_INST_NODE_HAS_PROP(n, label)
INIT_MACRO(n)
#endif
to use DT_INST_FOREACH(INIT_MACRO) instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The second paramater to IRQ_CONNECT for ipm_mhu_irq_config_func_0 should
be passing the priority, instead it passed the IRQ number. Fix this to
pass priority (which matches ipm_mhu_irq_config_func_1).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in arm_cmsdk/arm drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds the calls to read_timer_{start,end}_of_tick_handler()
to mark the start and end of ISR which will be used to display
the time spent in ISR with benchmarking tests.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add a k_timeout_t type, and use it everywhere that kernel API
functions were accepting a millisecond timeout argument. Instead of
forcing milliseconds everywhere (which are often not integrally
representable as system ticks), do the conversion to ticks at the
point where the timeout is created. This avoids an extra unit
conversion in some application code, and allows us to express the
timeout in units other than milliseconds to achieve greater precision.
The existing K_MSEC() et. al. macros now return initializers for a
k_timeout_t.
The K_NO_WAIT and K_FOREVER constants have now become k_timeout_t
values, which means they cannot be operated on as integers.
Applications which have their own APIs that need to inspect these
vs. user-provided timeouts can now use a K_TIMEOUT_EQ() predicate to
test for equality.
Timer drivers, which receive an integer tick count in ther
z_clock_set_timeout() functions, now use the integer-valued
K_TICKS_FOREVER constant instead of K_FOREVER.
For the initial release, to preserve source compatibility, a
CONFIG_LEGACY_TIMEOUT_API kconfig is provided. When true, the
k_timeout_t will remain a compatible 32 bit value that will work with
any legacy Zephyr application.
Some subsystems present timeout (or timeout-like) values to their own
users as APIs that would re-use the kernel's own constants and
conventions. These will require some minor design work to adapt to
the new scheme (in most cases just using k_timeout_t directly in their
own API), and they have not been changed in this patch, instead
selecting CONFIG_LEGACY_TIMEOUT_API via kconfig. These subsystems
include: CAN Bus, the Microbit display driver, I2S, LoRa modem
drivers, the UART Async API, Video hardware drivers, the console
subsystem, and the network buffer abstraction.
k_sleep() now takes a k_timeout_t argument, with a k_msleep() variant
provided that works identically to the original API.
Most of the changes here are just type/configuration management and
documentation, but there are logic changes in mempool, where a loop
that used a timeout numerically has been reworked using a new
z_timeout_end_calc() predicate. Also in queue.c, a (when POLL was
enabled) a similar loop was needlessly used to try to retry the
k_poll() call after a spurious failure. But k_poll() does not fail
spuriously, so the loop was removed.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Kernel timeouts have always been a 32 bit integer despite the
existence of generation macros, and existing code has been
inconsistent about using them. Upcoming commits are going to make the
timeout arguments opaque, so fix things up to be rigorously correct.
Changes include:
+ Adding a K_TIMEOUT_EQ() macro for code that needs to compare timeout
values for equality (e.g. with K_FOREVER or K_NO_WAIT).
+ Adding a k_msleep() synonym for k_sleep() which can continue to take
integral arguments as k_sleep() moves away to timeout arguments.
+ Pervasively using the K_MSEC(), K_SECONDS(), et. al. macros to
generate timeout arguments.
+ Removing the usage of K_NO_WAIT as the final argument to
K_THREAD_DEFINE(). This is just a count of milliseconds and we need
to use a zero.
This patch include no logic changes and should not affect generated
code at all.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Add possibility to change the measurement modes
of the temperature and humidity measurements to
continuous or single-shot mode or switch them off.
Signed-off-by: Christian Hirsch <christian.hirsch@tuwien.ac.at>
This commit updates the Atmel SAM GMAC driver to use the device tree
values for GMAC hardware configuration.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Use of macros such as SYS_POWER_STATE_SLEEP_2 needs to be guarded by
making sure CONFIG_SYS_POWER_SLEEP_STATES is defined.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The mcux lpc driver assumes that PINT interrupts are assigned to GPIO
port instances in groups of four, meaning that GPIO0 uses PIN_INT0-3 and
GPIO1 uses PIN_INT4-7. There was a mistake in the pin assignment
calculation that caused GPIO1 to incorrectly attach pins to PIN_INT0-3.
This caused the gpio isr to be invoked with what appeared to be the
wrong device argument and therefore not invoke any of the expected gpio
callbacks. But actually, it was the wrong irq that fired.
Found when adding support for the accelerometer interrupt on the
lpcxpresso55s69 board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add a missing include of debug/stack.h in order to fix the
compilation warning on implicit declaration of log_stack_usage().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Fixed one case in which the conversion to the new DT_INST macro's got
missed in the ws2812_gpio driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in litex drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the definition of DMA_SAM0_IRQ_CONNECT
pre-processor directive, so that it calls
DT_INST_IRQ_BY_IDX macro instead of
DT_INST_IRQ_HAS_IDX macro.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Convert DT_INST_0_SIFIVE_GPIO0_IRQ_##n to use the new DT macros:
DT_INST_IRQ_BY_IDX(0, n, irq). Also tweak a use of
DT_INST_IRQ_HAS_CELL(0, irq) to DT_INST_IRQ_HAS_IDX(0, 0) to match
style.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We have a number of cases that now look like:
#if DT_HAS_COMPAT(ti_lmp90077)
LMP90XXX_DEVICE(90077, 0, 16, 4);
#endif /* DT_INST_0_TI_LMP90077 */
The DT_INST_0_TI_LMP90077 comment is stale, and doesn't add much since
the #if associated with the #endif is just 2 lines up. Removing the old
comments seems the best cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add checks to prevent SPI transactions from being run in ISR
context. This affects both the LMP90xxx ADC and GPIO drivers.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move calibration setup SPI transaction to acquisition thread to allow
adc_read_async() to be called from ISR context.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Introduce a dedicated function for performing an entire LMP90xxx ADC
channel read and sample all channels in one go in the ADC acquisition
thread.
This removes the SPI transactions from adc_context_start_sampling()
which can be called in k_timer ISR context for consecutive ADC reads.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Since idc_read/idc_write are used outside of the driver we can't use the
DT_INST_... form (that utilize DT_DRV_COMPAT) of the macro's in
ipm_cavs_idc_priv.h. Use DT_INST(0, intel_cavs_idc) explicitly in the
header to fix the build issue.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add counter driver for the NXP Kinetis Low Power Timer (LPTMR). The
driver can be configured either as 16 bit counter or 16 bit pulse
counter.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert older DT_INST_ macro use in atmel sam0 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
With the introduction of ZephyrConfig.cmake all parts of CMake code
should rely on the CMake ZEPHYR_BASE variable instead of the environment
setting.
This ensures that after the first CMake invocation, then all subsequent
invocation in same build folder will use same zephyr base.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Just to get something to test for PM, via frdm_k64f board. So only this
board will get PM enabled.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
By changing the various *NET_DEVICE* macros. It is up to the device
drivers to either set a proper PM function or, if not supported or PM
disabled, to use device_pm_control_nop relevantly.
All existing macro calls are updated. Since no PM support was added so
far, device_pm_control_nop is used as the default everywhere.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Convert older DT_INST_ macro use in openisa drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added device tree nodes and associated headers for
defined uarts on the stm32g0 and stm32g07x 8x parts.
Tested with uart on stm32g071rb disco board with usart3 going to stlink.
Using shell.
Signed-off-by: Kieran Levin <ktl@frame.work>
Convert older DT_INST_ macro use in microchip drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in atmel sam drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in sifive drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in STM32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The primary problem was that the callback was being invoked twice,
which broke the tests.
A secondary issue is that when two level tests occur consecutively the
second will fail. Instrumentation confirms that the registers are
being configured correctly, and ip indicates that the condition was
detected, but the interrupt does not occur. Tests pass as long as no
level test precedes the failing test.
It's not clear whether this is an issue with the PLIC, or the GPIO
implementation (hardware or software). As "normal" GPIO applications
appear to work we'll run with it and keep an issue open.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The Atmel DFP headers define two "component typedef styles": RFO and
NTO; where the latter makes use of bit field structs to access hardware
registers.
The default component typedef style assumed by the DFP headers (i.e.
when `COMPONENT_TYPEDEF_STYLE` is not explicitly defined) is "RFO" and
this is indeed the component typedef style used throughout the Zephyr
Atmel SAM drivers, except in the particular instance which this commit
addresses.
The use of `GMAC_TA_Type` bit field struct, which is an "NTO" style
construct, is no longer possible with the latest DFPs because
conditional compilation checks for the bit field struct definitions
were added to restrict the use of such constructs to only when the
global component typedef style is set to "NTO".
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The new Atmel DFP USBHS component headers provide mode-specific
interrupt register field definitions that replace the generic
definitions (e.g. `USBHS_DEVEPTISR_RXSTPI` for a control endpoint is
now `USBHS_DEVEPTISR_CTRL_RXSTPI`).
This commit updates the Zephyr SAM USBHS driver to use the new
mode-specific interrupt register field definitions.
In addition, it maps the generic definitions to the mode-specific
definitions, as the revision A variant headers (e.g. same70a) in the
latest DFPs, at the time of writing, still provide only the generic
definitions.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Convert older DT_INST_ macro use in esp32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_INST_{0,1,2}_ESPRESSIF_ESP32_UART_IRQ_0 defines to something
non-DT prefixed. This way we know which defines are one's we generate
and which ones are driver created. It should be easy enough to replace
these INST_{0,1,2}_ESPRESSIF_ESP32_UART_IRQ_0 define with DTS generated
one macros once esp32 has interrupt controller support in DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in silab drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in cc13xx_cc26xx drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in stellaris drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds the per CPU address offset for intel_apl_adsp, so
the correct base address can be calculated under SMP.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a rather primitive driver for use with the Intra-DSP
Communication (IDC) on the DSP on certain Intel SoCs. The IDC
generates interrupts from one core to another by writing to
certain registers. This is also being utilized as
the scheduler IPI since it can interrupt other cores.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The DSP wall clock timer on some Intel SoC is a timer driven
directly by external oscillator and is external to the CPU
core(s). It is not as fast as the internal core clock, but
provides a common and synchronized counter for all CPU cores
(which is useful for SMP).
This uses the RISCV timer as base as it is using 64-bit
counter.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The CAVS interrupt controller has different base addresses for
each CPU. When running under SMP, the driver needs to look at
the correct address for the CPU the ISR is running so interrupts
can be dispatched correctly. This adds a function to calculate
the correct base address. Note that each supported SoC may have
different offsets so per SoC config will need to added. Support
for intel_s1000 is added as an example.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The dw_ictl interrupt controller is an interrupt aggregator
supporting multi-level interrupts. Therefore, it needs to be
initialized earlier than any downstream interrupt controllers
and devices.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The cavs_ictl interrupt controller is an interrupt aggregator
supporting multi-level interrupts. Therefore, it needs to be
initialized earlier than any downstream interrupt controllers
and devices.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
It was observed that leaving the pin type configured for i2c for SDA
and SCL results in higher power consumption during standby. So we are
resetting the pin type when bringing the i2c into low power mode, and
setting it back to the correct type when exiting low power mode.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Add a dependency on the I2C resource in the TI Power module,
reconfigure the peripheral upon CPU exiting standby, and add
support for device PM.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Add a dependency on the UART resource in the TI Power module,
reconfigure the UART upon CPU exiting standby, and add support
for device PM.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Adding a dependency on the GPIO resource in the TI Power module, and
configuring the edge detection on pads as a wakeup source.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
z_vrfy_counter_get_value should check the size of memory pointed to
ticks and not the size of the pointer.
Fixes: #22431
Coverity CID :207984
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The shared irq support isn't needed in this driver. We just need to
deal with the fact that some SoCs have only a single interrupt line and
some have three interrupts. We can just ifdef that based on
DT_NUM_IRQS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Calling device_set_power_state() with DEVICE_PM_SUSPEND_STATE then
DEVICE_PM_OFF_STATE creates an assert in nrf driver
Signed-off-by: Ismael Fillonneau <ismael.fillonneau@stimio.fr>
In the default configuration of the stm32g4 is the dual bank mode.
In dual bank mode, the flash is split into two banks with 256k each.
The erase pages have a range form 0 to 127, where each page has 2k.
If one wants to erase an area above 256k, the driver has to switch
to bank 2 befor erasing. Otherwise it will erase the page moulo 127.
Signed-off-by: Alexander Wachter <alexander.wacher@leica-geosystems.com>
This commit introduces some logs in the stm32 flash implementation.
Thith the logs it is easier to locate problems when they arrise.
Signed-off-by: Alexander Wachter <alexander.wacher@leica-geosystems.com>
A txcnt of zero prevents transmission, as transmit requires the number
of entries in the transmit fifo to be strictly less than the txcnt
value. Set the default to 1.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Convert the driver to use DT_INST_ defines, update all dependent dts,
soc and board files.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This allows us to start using DT_NODELABEL() to access SPIMs that way,
instead of via an alias.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
uart_configure verification handler was missing what would cause a crash
if called from a user thread.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add the get_entropy_isr API function for the gecko entropy
driver. When the function is invoked without the ENTROPY_BUSYWAIT
flag, it returns whatever data is available in a non-blocking manner.
Signed-off-by: Pooja Karanjekar <pooja.karanjekar@lemonbeat.com>
Starting a SMI write operation without waiting for completion of the
preceding SMI read operation cause the write operation to fail if
the time between the 2 operations it too short. This leads to the
PHY being in an unusable state on the MIMRT1060-EVK eval board.
In addition the value of the register was not used, as consequence
some bits were not preserved.
The solution is to do a read/modify/write to set only the
ref clock bit, which sets the PHY into 50MHz clock mode,
and keep the value of the other bits.
Signed-off-by: Armand Ciejak <armand@riedonetworks.com>
Force PHY normal operation in eth_mcux_phy_setup in case strap-in
pins configure the PHY in factory test mode.
Signed-off-by: Armand Ciejak <armand@riedonetworks.com>
Don't use DT_INST_0_SOC_NV_FLASH_LABEL as device name.
Use DT_FLASH_DEV_NAME instead
Fixes#23678
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
At OpenThread stack on ieee802154_radio_handle_ack method the
net_pkt_read fail because net_pkt_cursor wasn't proper initialized.
This ensures that net_pkt_cursor is initialized for any ack frame.
Another hidden problem fixed was the frags property on net_buf. Now
it is defined as NULL to ensures that no fragments are available.
The ack frame should be returned to OT only if requested. In this
case, the IEEE 802.15.4 Frame Control field from TX frag is now
verified for an ACK request and if OT requires ACK response it will
be proper handled and dispatched.
Fixes#23595
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit reworks the Xilinx TTC timer driver to use the "match" mode
instead of the "interval" mode which counts up to the specified value
and resets to zero.
Using the "match" mode ensures that the timer keeps counting even after
an interrupt is triggered, and facilitates the tickless mode support
implementation.
This also allows `z_timer_cycle_get_32` to return the correct cycle
count when interrupt is locked; thereby, fixing the k_busy_wait hang
issue.
Note that the TTC "match" mode emulation (and tickless timer operation)
is only stable when the QEMU icount mode is enabled.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This adds support for the Espressif ESP8266 and ESP32 devices to be used
as peripherals on a UART.
There are two main AT command versions that can be selected, 1.7 and
2.0. Since they behave a bit different it is important to select the
one that matches the used in the firmware on your device.
When downloading large amounts of data it is highly recommended to
enable CONFIG_ESP_PASSIVE_TCP and flow control on the UART so that
data is not lost due to UART speed or receive buffer size.
Currently unsupported:
- Changing UDP endpoint with a sendto()
- Bind to a specific local port
- Server socket operations, ie listen() and accept()
Official AT firmware for ESP8266 and ESP32 can be found at:
https://github.com/espressif/esp-at
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
This commit adds the "monitor task" to detect and report any changes
in the PHY link status to the operating system.
The monitor task is perodically executed to poll the link status from
the PHY and call `net_eth_carrier_{off,on}` based on the detected
link status change.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The `link_configure` function currently configures the `GMAC_UR`
register and forces the RMII interface.
This is not necessary because the `GMAC_UR` register is already
configured with an appropriate value based on `CONFIG_ETH_SAM_GMAC_MII`
in `gmac_init`.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the PHY link status query function that can be used
for detecting the Ethernet connection.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The IIS2MDC is a 3D digital magnetometer ultra-low power sensor
for industrial applications, which can be interfaced through
either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2mdc.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Added return -ENOTSUP in uart_rx_enable() if RX pin is disabled.
Fixed power management call where TASKRX was started even though
RX pin was disabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Extended nrf_uart driver to support TX only.
When RX pin is not provided then RX is not started at all. This
allows to achieve low power with logging/console enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add a fixed clock to the qemu-virt-a53.dtsi to match how the musca dts
files work so we get the clock DT info in the same way in the driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add interface name to link up/down information message
to help tracking which port is changing status.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
Copy paste error, base address of second controller was set to the
same as the first one, corrected to ENET2.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
With Ethernet controller base address is not straight forward
to figure out if it is ENET or ENET2l, using name is much better.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
This will allow having a different PHY address for each controller.
It also avoids for the PHY address to be hard-coded in several
functions.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
Add new config allowing to enable the second Ethernet port
on i.MX RT1060 SoC family.
Signed-off-by: Armand Ciejak <armandciejak@users.noreply.github.com>
Source and destination ports should be set properly
when assembling the receive socket data.
Signed-off-by: Ryan Erickson <ryan.erickson@lairdconnect.com>
Coverity doesn't invoke the build for this module with a configuration
that provides a non-zero delay for entering or releasing deep power
down, so it sees a check that a value known to be non-negative
magically became negative without being touched, and so screams about
dead code.
Refactor to make the adjustments unconditional which has the same
effect in any reasonable level of optimization while making it
slightly less obvious that the value may not change.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add entropy driver based on GECKO TRNG module along with device
tree support for EFM32PG and EFR32MG SOCs.
Signed-off-by: Pooja Karanjekar <pooja.karanjekar@lemonbeat.com>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This reverts commit 979ed4e1cd.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add a missing include of debug/stack.h in order to fix the
compilation warning on implicit declaration of log_stack_usage().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Reworked calibration to not use HW platform which is not available on
some platforms (nrf53) and does not bring any value compared to using
system timer. Switched to use k_timer. Additionally, improved
calibration algorithm to request also LF clock before starting
calibration. This simplifies the algorithm because it does not need
to support disabling low frequency clock which in calibration.
Tests has been updated and simplified. Former tests relied on HW timer
event.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit fixes the field definition names for `GICD_ICFGR`, which
were incorrectly prefixed with `GICC_`.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Change adds waiting until PWM is stopped before restarting it. Without
the change, calling the pwm_nrfx_pin_set function multiple times in
quick succession could cause a race condition causing the PWM to
remain stopped in case it should be restarted.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
The ISM330DHCX is a ultra-low power IMU with a 3D digital accelerometer
and 3D digital gyroscope tailored for Industry 4.0 applications, which
can be interfaced through either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/ism330dhcx.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
LPUART1 TX alternate function number for PB6 was not correct in the
pinmux settings for H7 series.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
With new NXP HAL, MCUX CSI does not necesseraly start the
capture into the first submitted buffer. However the driver
expects that buffers will be captured in submitted order.
Fix that.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
k_mem_pool_malloc reserves some space for block descriptor at the start
of the data block, causing misalignement of returned video buffer.
In our context we want to return a video buffer with aligment matching
the video buffer poll alignment config. Fix that by using the simpler
k_mem_pool_alloc function.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
After RX is disabled during receiving, some bytes are received to
internal fifo. To not interfere with further transactions fifo has to be
flushed.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Add Virtual LAN support to stm32 Ethernet driver. Refactor the
eth_iface_init() and move device configuration settings to
eth_initialize() as the eth_iface_init() is called multiple
times (once / configured VLAN).
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Towards cleaning up (and hopefully removing dts_fixup.h in the near
future). We need to move the handling of different names for the irq
flag propety into the driver and out of dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Towards cleaning up (and hopefully removing dts_fixup.h in the near
future). We need to move the handling of different names for the irq
flag propety into the driver and out of dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch is setting the pin to very high speed for all
the SPI2 clock outputs, for the stm32f7 soc series.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Convert usb_stm32 driver to use of DT_INST macros.
Since driver is compatible with 3 different dt compatibles and
compatible string is included in DT_INST macros, I've kept the
DT_USB_ compatible agnostic macros based on DT_INST ones, which
allowed to remove fixup definitions.
Use of DT_USB symbols is now limited to usb_dc_stm32.
Additionally, compatible "st,stm32-otgfs" is removed from list
of compatibles for usbotg_hs ips.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST_ defines.
In the process, we've removed all UART/USART/LPUART code in
device instanciation code which had no impact.
Since all uart/usart/lpuart nodes declare compatibility with
st,stm32uart, DT_INST_X_ST_STM32_UART_FOO could be used.
Removed DT_UART fixup macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On stm32 spi devices, there are 2 main IP variants, with and w/o
fifo. Fifo is not really used today, but still there is some
additional code handling fifo. Today this code is protected under
Kconfig symbol SPI_STM32_HAS_FIFO.
This code carries redundant information vs dedicated compatible
"st,stm32-spi-fifo", which is provided as unique driver compatible
for devices supporting this IP as opposed to use of "st,stm32-spi"
when fifo is not supported.
Having these 2 compatibles defined exclusively is not convenient for
migration to DT_INST as DT_INST macros contain compatible string and
hence it cannot be used to provide common compatible code for devices
defining different compatibles.
Based on these observations, review stm32 spi devices compatible
declarations. Devices supporting fifo will now declare both
compatibles, as proposed by dt spec: "[compatible] property value
consists of a concatenated list of null terminated strings,
from most specific to most general". Hence field will now be:
"st,stm32-spi-fifo", "st,stm32-spi"
This way, fifo enabled stm32 spi devices will generate both:
DT_INST_STM32_SPI_FOO and DT_INST_STM32_SPI_FIFO_FOO
As well as:
DT_COMPAT_ST_STM32_SPI and DT_COMPAT_ST_STM32_SPI_FIFO
So, DT_INST_STM32_SPI_FOO could be used for device initialization.
Also DT_COMPAT_ST_STM32_SPI_FIFO could be used for FIFO handling
code inside driver. Hence use it to replace Kconfig symbol
SPI_STM32_HAS_FIFO.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST_ defines.
Removed DT_FLASH_DEV fixup macros, except DT_FLASH_DEV_NAME
used in applications.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST_ defines.
Removed DT_RTC_0 fixup macros but keep DT_RTC_NAME_0 as it is
still in use across RTC users.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The RX fragment debug print does not work (compile error)
if memory allocation debugging is enabled, so disable it
for time being.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In the DT_INST conversion we introduced a typo bug of accessing port0
instead of port1 in the IRQ config function.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configure the PWM period and pulse width in timer ticks instead of
calculating the frequency and duty cycle for use in the higher level
MCUX API. This improves the resolution of the PWM output signal
considerably.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The IIS2DLPC is a 3D digital accelerometer ultra-low power sensor
for industrial applications, which can be interfaced through either
I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2dlpc.pdf
This driver is based on stmemsc i/f v1.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Telnet console was move as a shell backend and is not anymore part of
console drivers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Enable counter driver support for H7 series. Tested with H743ZI MCU
using samples/drivers/counter/alarm.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The current design of the network-specific stack dumping APIs
is fundamentally unsafe. You cannot properly dump stack data
without information which is only available in the thread object.
In addition, this infrastructure is unnecessary. There is already
a core shell command which dumps stack information for all
active threads.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Update device data with the activated configuration, so that it
will be remembered for follow up configuration get requests.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Change to code to use the automatically generated DT_INST_*
defines and remove the now unneeded configs and fixups.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
The sole purpose of init options has been to enable hardware flow
control on NS16750 when asked. Use the proper DTS tags for this.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Expand configuration mechanism for additional eSPI host warnings.
Notify client driver when sleep A virtual wire is received.
Simplify virtual wire interrupt enabling.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
There is timeout guard, in form of k_sem_get within work_in_time_slice,
used to detect if flash operation takes longer than expected maximum
and to return error code in such case. The processing of this timeout
is missing cancellation of scheduled ticker job that would attempt to
perform another operation. This causes problem as context for ticker
is created, on stack, within erase/write_in_timeslice which
would conclude when timeout occurs, folding the stack in process.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Added locking for TX transfers between async and polling API.
Added safety counters for checking if transmission finished.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Add locking between async and polling tx transfers.
Add safety counters while waiting for transmission to finish.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
The current Generic Interrupt Controller (GIC) driver makes use of the
multi-level interrupt mechanism and `irq_nextlevel` public interface.
This is a less-than-ideal implementation for the following reasons:
1. The GIC is often used as the main interrupt controller for the
Cortex-A and Cortex-R family SoCs and, in this case, it is not a 2nd
level interrupt controller; in fact, it is the root interrupt
controller and therefore should be treated as such.
2. The only reason for using `irq_nextlevel` here is to interface the
architecture implementation to the interrupt controller functions.
Since there is no nesting or multiple instances of an interrupt
controller involved, there is really no point in adding such an
abstraction.
3. 2nd level topology adds many unnecessary abstractions and results
in strange coding artefacts as well as performance penalty due to
additional branching.
This commit refactors the GIC driver interface as follows:
1. Remove the current GIC driver interface based on the multi-level
interrupt mechanism and the `irq_nextlevel` public interface.
2. Define the GIC driver interface in
`include/drivers/interrupt_controller/gic.h` and allow the arch
implementation to directly invoke this interface.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
MEC15xx eSPI OOB RX length register holds received message length
and receive buffer length, need to extract rcvd msg length.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
for smp target, there is a case where just one core is running, then:
* during init, the master core will run, others cores will halt/sleep
* use timer driver for single core
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Add CAP_NO_IV_PREFIX capability support to the STM32 CRYP crypto driver,
so the initialization vector does not have to be prefixed to the
plaintext/ciphertext buffer.
Signed-off-by: Markus Fuchs <markus.fuchs@de.sauter-bc.com>
The loopback driver is a simple driver that can be used to
test CAN subsystems. The actual implementation sends frames
in the same thread that calls the send function.
Some libraries have problems with that behavior.
This PR implements a dedicated thread that calls the callback
for the receiving functions and a msgq in between the sender
and the TX thread.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Attempt to deinitialize an nrfx driver that is not initialized results
in an assertion failure reported by the driver. And such attempt could
happen in SPI shims when the power state was switched between states
other than ACTIVE.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use DT_INST_* instead of the hard-coded macro from the HAL,
as DT_INST_* are preferred.
Fixes#17775
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Some commands need to be processed before a "\r\n" is available and
there might also be commands that have "\r\n" as data but doesn't mean
the end of the command.
To solve this a MODEM_CMD_DIRECT has been added. cmd_handler_process()
will look for matching direct commands before checking if a whole line
is available for matching the normal commands.
A direct command can return either -EAGAIN, meaning that more data is
needed or it will return the number of bytes to skip forward, ie the
length of the command that was handled.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
Introduces a new SDL mouse driver for the keyboard scan (kscan)
interface. Driver is implemented as SDL event filter
Signed-off-by: Pavlo Hamov <pavlo_hamov@jabil.com>
Convert driver to use DT_INST_ defines. The preferred defines for
drivers are DT_INST_. The driver mostly used DT_INST_ defines but
a few IRQ priority defines needed conversion.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. The preferred defines for
drivers are DT_INST_.
As part of this change we utilize the device tree for GIRQ info and
rename timer3 to 2 since we are doing this by instance number.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. There was just one case for
CS_GPIOS that wasn't using DT_INST defines already.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to fully use DT_INST_ defines. Currently IRQs are not
generated from DTS on esp32 so we create #defines for what they should
look like. Convert the IRQ defines to match DT_INST style so if/when
we have that info in DTS it will look the same.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. Replace dts_fixup.h use
for DT_RTC_0_NAME with DT_INST_0_NXP_KINETIS_RTC_LABEL to be
consistent. Also, remove the aliases that had been used for this
driver in various nxp_k*.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines and remove Kconfig per instance
enablement in favor of DT_INST_ define existing. Also, remove the
aliases that had been used for this driver in nxp_rt.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
