On iMX.RT devices, the number of GPIO pins exceeds the maximum of
64 that the PINT interrupt controller can support. Therefore, two
interrupt lines are now shared between the GPIO modules.
This patch allows the user to set the interrupt source for a GPIO
peripheral. For most LPC devices, this will always be the PINT. For some
RT devices, the PINT cannot use pins on GPIO modules other than 0 and 1
as input, and thus the INTA and INTB sources should be used.
Since Zephyr does not support sharing these interrupt between all GPIO
controllers, the user must configure a subset of all GPIO controllers to
use the shared module interrupts. An example of how to do so is provided
for the RT595 EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce PINT driver, for NXP pin interrupt and pattern match engine.
The driver currently supports only the pin interrupt feature of the
PINT.
Add DTS entires for the PINT on LPC and RT devices that support this
peripheral, and remove the interrupt defintions that are PINT specific
from the GPIO module on these devices.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The I2CLCTL_MLCS setting was recently added to MTL
platform. LNL has these registers in separate space, therefore
new field is added to intel,ssp-dai.yaml and appropraite definitions
to LNL device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Repleace usage of shim2 device tree field with hdamlssp.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In current implementation the HDAMLI2SL register is represented by
shim2 field in common SSP device tree file. This could be misleading
since the filed is is different location to I2S IP.
Adding separate device for this register following DMIC case.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A recent change added the stop-bits and data-bits to the base
uart-controller binding, meaning it's no longer required to
be added in the Altera specific binding.
This requires no further changes because its only use is in
uart_altera.c where only the index of the enum is used,
which remains the same between the new implementation and
how it was previously implemented in the altera specific binding.
Relevant commit: 0234f12
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Add the header file required for the example to work. Users get the
following error due to unresolved INPUT_BTN_* values otherwise:
parse error: expected number or parenthesized expression
Signed-off-by: Amit Kucheria <amitk@kernel.org>
Signed-off-by: Amit Kucheria <amit@mbedrock.com>
These bindings are removed because they are now handled in the
included base uart-controller.yml.
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Add bindings for LTC1665/LTC1660, which is a 8/10-bit
Digital-to-Analog Converter with eight individual channels.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
This addition should help users to better understand potential issues
with domain clock configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In ACE 2.0 platform (LNL) dmic got two new shim register ranges.
DMIC driver need to program them to configure the interface.
This patch adds new shims to device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
The temperature sensor of the STM32F0x0 is similar to C0 (with one value
for calibration) but uses a negative coefficient, so we add it to the
bindings, just like in st,stm32-temp.yaml
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add a devicetree binding for the CAN-FD capable variant of the NXP FlexCAN
controller. Add example devicetree snippets to both NXP FlexCAN and NXP
FlexCAN-FD binding documentation to limit confusion.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the nxp,kinetis-flexcan devicetree compatible to nxp,flexcan as it
is not specific to the NXP Kinetis series.
This is preparation for adding a nxp,flexcan-fd binding.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add new compatible to separate production calibrated sensors
with single and dual calibration temperatures. Also update
stm32_temp driver to support single calibration sensors.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
Adds support for a devicetree property that controls the ClockDiv
value provided to the SDIO during init.
Signed-off-by: Maxmillion McLaughlin <github@maxmclau.com>
Zephyr SPI driver model for full-duplex operation assumes
data will be transmitted and received during each clock period.
The QMSPI driver for the XEC family also supported dual and
quad I/O use cases which are inherently half-duplex. To
support dual/quad the driver incorrectly processed spi buffers
as all transmit buffers first then all receive buffers. This
worked if only the SPI driver was used. It did not work with
the Zephyr flash SPI NOR driver which assumes SPI drivers
follow the SPI driver model. This commit implements a QMSPI
driver that follows the Zephyr SPI driver model resulting in
a slightly smaller driver. Dual/quad SPI transactions are
supported if the experimental SPI extended mode Zephyr
configuration flag is enabled. We also remove the QMSPI full duplex
driver added previously to support the flash SPI NOR driver.
Added board to spi loop-back test and spi_flash sample.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Arm fvp_baser_aemv8r and fvp_base_revc_2xaemv8a boards are using
SMSC91C111 as their ethernet adapters.
Portions of the codes are based on FreeBSD code from its
'src/sys/dev/smc/if_smc.c' and 'src/sys/dev/smc/if_smcreg.h'.
This driver has two parts, one is the ethernet controller driver, which
is MAC layer driver. The other is the MDIO driver, which is the PHY
layer driver. Both of them are in the same source file due to that they
need to share the same reading and writing register functions and
the smsc object.
The mdio driver is needed by the existing 'phy_mii' driver, which is
a driver for the generic MII-compliant PHY.
This driver was developed under the fvp_base_revc_2xaemv8a target and
has been tested on the fvp_baser_aemv8r target.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
move DT_DRV_COMPAT to bmm150.h. so that can be decide which interface
to use.
define struct bmm150_bus_io interface for bmm150_i2c.c and bmm150_spi.c
in bmm150.h.
redefined bus operation interface in bmm150.c, this allow the driver
to decide which interface to use during construction.
Signed-off-by: Weiwei Guo <guoweiwei@syriusrobotics.com>
Convert the SDL driver to use the input subsystem. This is specifically
meant to emulate touchscreen drivers, so it's setup to send triplet of
x, y, touch for touch-on events and just touch off on touch off events.
Renamed the driver to input-sdl-touch since now we can also develop an
sdl driver for simulating key events.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This commit adds support for ANY_MOTION and DATA_READY interrupts for
the BMI270. To implement this, a different config blob than the
"max_fifo" blob has to be used.
Signed-off-by: Benjamin Lindqvist <benjamin@eub.se>
This adds the i2c driver for the Renesas SmartBond(tm) MCU family.
It supports blocking transfers and callback transfers.
Currently only supports controller mode.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Under disk bindings. NVMe is a purely PCIe based technology, thus the
relevant includes.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This adds a driver for the DS2482-800 1-wire multi channel bus driver.
The driver uses a split architecture in order to share a common lock
among all configured channels of a single IC.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Add test for the experimental feature GPIO_ENABLE_DISABLE_INTERRUPT,
which covers APIs gpio_pin_interrupt_enable() and
gpio_pin_interrupt_disable().
Signed-off-by: Sung-Chi Li <lschyi@google.com>
Use the LTDC in combination with the DSI HOST makes the pinctrl obsolete.
DSI HOST has dedicated pins.
Signed-off-by: Rico Ganahl <rico.ganahl@bytesatwork.ch>
The driver has been recently moved under the input subsystem but the
corresponding driver was left over. Move it from kscan to input.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Give precision to the description of the dma phandle in the
quadspi node.
When a DMAMUX is present and enabled, the channel is the dma one
(not dmamux channel) and the request is given by the DMAMUX.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The emulated RTC device driver is used to emulate a real
RTC device. Note that it is not a replacement for the
native_rtc module, which is used to control simulated time,
get time from the host system, etc.
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
This test suite adds tests for the following:
- Setting and getting time
- Validating time is incrementing correctly
- Validating behavior of alarms with callback disabled
- Validating behavior of alarms with callback enabled
- Validating update callback
The test suite uses the devicetree alias rtc to find
the device to test.
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
Add optional filter value properties. The filter is disabled by default
but can be enabled by setting the filter-sample-period > 0 in the dts
file. A latency is introduced if the filter is enabled. The latency can
be printed by setting sensor log level to debug.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
This commit implements the temperature sensor interface for
the Maxim MAX31865 SPI Temperature Sensor.
Signed-off-by: Fin Maaß <fin.maass@haw-hamburg.de>
Co-authored-by: Armin Brauns <armin.brauns@embedded-solutions.at>
In ACE 2.0 platform (LNL) ssp got new shim registers.
SSP driver need to program them to configure the interface.
This patch adds new shims to device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
This commit adds definition of ACE 2.0 Lunar Lake board.board.
Signed-off-by: Krzysztof Frydryk <Krzysztofx.Frydryk@intel.com>
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Adds tmd2620 driver and devicetree bindings to work in
trigger and polling mode supporting Power management.
Signed-off-by: Peter Fecher <p.fecher@phytec.de>
Add LEDC device for esp32s3
Update PWM LED binding
Remove invalid comment from driver source file
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Enabled simultaneous support by adding a DTS variable named “io-mapped”.
There are 3 possibilities through instance in dtsi file.
Under PCIe, PCIe ns16550.
Under soc and has a variable io-mapped, legacy(IO mapped).
Under soc and don’t have a variable io-mapped, MMIO mapped.
Simultaneous access can be enabled by a Kconfig.
For PCIe instances UART initialization should be done post-kernel as it
depends on PCIe initialization.
Co-authored-by: Najumon BA <najumon.ba@intel.com>
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Add the `zephyr,pm-device-runtime-auto` flag to `pm.yaml` and
`struct pm_device`.
This flag is intended to signify to the boot system that device runtime
PM should be automatically enabled on the device after the init function
has run.
Only run `pm_device_runtime_auto_enable` function on a device if
initialisation succeeded. This prevents actions being run on devices
that are not ready.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Added a new watchdog driver which can handle a multiple wdt_dw instances
and can control the pause signal.
The mlt platform has three designware watchdogs, one for each core.
I decided to create a separate intel watchdog driver for the following
reasons:
1. All three devices share the same interrupt number. Each watchdog reports
an interrupt to the core to which it has been assigned. The same interrupt
number cannot be used by multiple devices in the device tree. So, it would
be assigned to only one device. The other dw watchdog devices would use
this assignment, even though it would not be described for them in the dt.
The interrupt handler function in dw watchdog checks the interrupt flag.
If the interrupt was connected to the first watchdog, and the second or
third watchdog signal an interrupt, the interrupt handler of the first
device would ignore it because it would not have set the interrupt flag.
The watchdog device don't knows anything about the existence of the others
devices.
2. The designware watchdog only supports a hardware pause signal. It cannot
be paused programmatically. On the mtl platform, there is a separate group
of control registers for all per-core watchdogs. There are GPIO-like
registers that allows control of a hardware pause signal for subordinate
watchdogs. This separate block is shared by all three watchdogs.
3. The base addresses of the subordinate watchdogs are read from the
aforementioned control registers. As a result, in the device tree we have
only one base address for the intel watchdog, which points to the pause
control registers and containing the base addresses of the subordinate
devices.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Add a driver that listens for input events and reports them on a kscan
API. This allows porting kscan drivers to the input APIs while
maintaining compatibility with the existing kscan based applications.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This patch makes possible to choose custom byte which should be used
to enable non-permanent readout protection (RDP1). Actually, any byte
except 0xAA and 0xCC (which are used by RDP0 and RDP2 respectively)
can be used to enable RDP1 but in multi-image environment, some other
image could check if RDP1 is enabled by comparing it to some hardcoded
value.
If property is not defined, 0x55 will be used to enable RDP1. The
default value comes from STM32 HAL.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Update DMA bindings with DMA config macros
only for st,stm32-dma-v2.yaml and st,stm32-dma-v2bis.yaml
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
Adds the new stm32h5 serie to the list of st,stm32g0-exti
compatible : now the matching targets is C0/G0/H5/U5/L5/MP1.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add binding and sensor attribute to allow single phase
mode where only one signal is required from the encoder.
The signal must be connected to Phase A input.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add a GPIO nexus binding for Pmod interface connectors.
This commit also includes a header file with macros
that map signal names in the Pmod specification to
the corresponding indices in the GPIO nexus, meant for
use in devicetree files.
Signed-off-by: Alexander Mihajlovic <alexander@eub.se>
Add an input device to take input key events as an input and generates
short press or long press devices as output.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The number of available EasyDMA MAXCNT bits is now defined per-instance
in Devicetree.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Change device tree VW routing to a form allowing overrides.
Add two new DT optional properties for specifying the reset
source and reset value of each virtual wire. Only virtual
wires that are enabled using the status property are modified.
NOTE: eSPI virtual wires are controlled in groups of 4 by
hardware. The optional reset signal source properties applies
to all four virtual wires in the group. If this field is
changed from the hardware default, it should be changed for
only one virtual wire in the group. If the property exists
in more than one wire in the group it must be set to the
same value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Modify Mircrochip MEC172x eSPI driver to get eSPI virtual wire
hardware routing from device tree.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The clock control driver requires three pieces of information:
PCR register index, bit position, and clock domain. Clock domain
was missing from DT information and MCHP macros.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Deleted adc_mchp_xec.c and microchip,xec-adc.yaml file.
DTSI, yaml, CMakeLists.txt and Kconfig.xec files are
updated for compatible.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Updated the "adc_mchp_xec_v2.c" adc driver to support both MEC172x and
MEC15xx SOC.
ADC smapling clock configuration updated using DTS.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
The regulator driver has a configured min/max range that is used
to limit set values, and to initialise the regulator.
A new init value has been added, so that the startup voltage can
be higher than the lowest permitted value.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
Added initial version of Infineon cyw43xxx BT (
H4 HCI extension drivers/bluetooth/hci/CMakeLists.txt)
Add initial version of binding file for Infineon CYW43xx BT
HCI extension driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
This adds a basic Intel TCO watchdog driver. The driver doesn't support
windowed timeouts (a non-zero window.min value) or callbacks. The driver
currently assumes TCO version 6, which can be found e.g. on Elkhart Lake
and Raptor Lake platforms. The driver also expects the TCOBA base
address to be specified through DTS, rather than doing runtime lookup
(using e.g. ACPI or PCIe).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remedial rework to handle the enabling of the I2S master clock
output based on the presence of an introduced DT property.
For details see issue/54841.
Signed-off-by: Raul Pando <raul.pando@bytegrity.co.uk>
Add initial version of clock control for Atmel SAM SoC series. This add
support to Power Management which allows control peripherals clock.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add support for the TI TPS382x series. The IC has an input pin which
should be toggled by the processor and a output pin which should be
connected to the RESET input of the processor. The timeout is not
configurable.
This device can be used by devices which does not have any internal
hardware watchdog device.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Modifying counter drivers (rtc and timer) to rely completely on
device tree and not on Kconfig of MDK flags.
Adapting dtsi for all SoCs and adapting test configuration.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Adds a driver for the Nordic nRF GPREGRET registers and adds
entries to the SoCs for this peripheral.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Add support for virtual UART device that uses ARC Hostlink channels
for data transfers. Due to the Hostlink principle, this driver
supports only polling API.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
This symbol allows users of the driver to disable the
power management feature of just this sensor if they are
not using the int_gpios pin of the BQ274XX.
Signed-off-by: Nick Ward <nix.ward@gmail.com>
interrupts property was previously added with "required: false", but
when required was removed (redundant), the interrupts property was left
dangling.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
To enable Bluetooth controller coexistence feature, there is
implementation of ticker task, which aborts any ongoing radio events
during assertion of the grant pin. This solves the co-existence issue
in the role of the subordinate transceiver.
Signed-off-by: Tomáš Beneš <tomas@dronetag.cz>
The zephyr,gpio-keys is now emitting input events, so it makes sense to
require a key code to be set. Change the zephyr,code property to be
required and add an example in the binding description.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Port the gpio_keys_zephyr driver from the gpio subsystem with a
dedicated API to the input subsystem reporting input events.
Move the test as well, simplify the cases a bit since the API is simpler
now.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The 200ns reset time specified in the datasheet are a minimum time; and the
nanoseconds were being rounded to whole microseconds anyway.
Also make it the same type as `config_delay_us` (`uint16_t`).
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
From FPGA-TN-02001-3.3 "iCE40 Programming and Configuration":
> After driving CRESET_B High or allowing it to float High, the AP must
> wait a minimum of 1200 µs, allowing the iCE40 FPGA to clear its internal
> configuration memory.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
The board embeds an audio codec IC, Cirrus CS42L73. While there is no
in-tree driver for it, we need a binding to describe how it is wired in
the board, e.g. for IRQ/RESET lines.
Following Linux binding for the same IC, create one in
dts/bindings/sound. Note that Linux binding is less complete/outdated.
Ref. https://statics.cirrus.com/pubs/proDatasheet/CS47L63_DS1249F2.pdf
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add driver for Xptek XPT2046 resistive touch controller on SPI.
Only interrupt driven mode supported, does not do polling.
Signed-off-by: Seppo Takalo <seppo.takalo@iki.fi>
Introduce driver for NXP DCNANO LCDIF (lcd interface) peripheral,
present on iMX.RT500. Currently this driver only supports updating
the primary framebuffer, and does not implement support for the cursor
buffer present on this IP.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce driver for MCUX MIPI DSI 2L. This IP block differs slightly from
the existing MCUX MIPI peripheral, and uses a different hardware
abstraction layer. For these reasons, a new driver was introduced rather
than extending the existing mcux_dsi implementation.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Allow configuration of AHB RX buffer allocation. This allows sections
of the AHB RX buffer to be reserved for specific masters, which can
enhance performance.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The driver utilizes ST Microelectronics library (which
exists in modules\hal\st\sensor\vl53l1x. Platform specific
headers and source files used by the library are included
and adapted for Zephyr.
The driver can be configured in proj.conf to use a
interrupt/polling methods and the use of the XSHUT pin on
the VL53L1X. All uses were tested successfully.
Signed-off-by: Mark Watson <mwatson@prosaris.ca>
This patch adds watchdog driver for Renesas Smartbond SOCs.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
This adds driver for SmartBond TRNG peripheral that with separate
ISR an thread data pools.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Add support for configuring power on delay when using SPI SDHC. This
allows cards that reliably initialize with a shorter (1ms) delay to
avoid the long initialize delay otherwise imposed.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add I2C bus recovery support to the STM32 v1 and v2 driver. The STM32 i2c
peripheral does not natively support I2C bus recovery so recovery is
performed using GPIO bitbanging. This mirrors the bus recovery
implementation for NXP MCUX LPI2C driver.
Fixes: zephyrproject-rtos#54917
Signed-off-by: Maxmillion McLaughlin <github@maxmclau.com>
Added initial version of Infineon CAT1 GPIO driver.
Added initial version of binding file for Infineon CAT1 GPIO driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Infineon CAT1 UART driver.
Added initial version of binding file for Infineon CAT1 UART driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Infineon CAT1 Pin controller driver.
Added initial version of binding file for Infineon CAT1 Pinctrl driver.
Added initial version of dt header for Infineon CAT1 pinctrl driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Provide dts binding for F412 PLL I2S.
This I2S dedicated PLL is fully configurable and take same
input as Main PLL
Only one output clock (PLLR) is supported for now.
This PLL could be found on STM32F412 and F413 parts for instance.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Provide dts binding for F4 PLL I2S.
This PLL share input source and input M diviso with F4 Main PLL.
Only one output clock (PLLR) is supported for now.
This PLL could be found on STM32F401 parts for instance.
Additionally, provide related header definitions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Polarity support added to XEC PWM driver. This allows (for example) PWM
controlled LEDs that are active low to actually be turned off when set
to off.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Rework the Host Command support. It includes:
-change API to backend
-change a way of defining rx and tx buffers
-fix synchronization between the handler and backend layer
-simplify the HC handler
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Follow naming pattern in the subsystems(logging or shell) and name
the layer between generic handler and peripheral driver "backend".
The name doesn't suit that well to the SHI backend, because there isn't
SHI API itself and the SHI interface is used only for the host
communication. So the backend code includes the peripheral driver itself.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add the implementation for the akm09918c magnetometer driver.
Additionally, add the appropriate node to the TDK robokit1 device
tree. In order to prevent regressions, add the sensor to the sensor
build_all tests and specific tests using an emulator.
Signed-off-by: Yuval Peress <peress@google.com>
Add a driver implementation that uses the I2S peripheral.
Based off this blog post:
https://electronut.in/nrf52-i2s-ws2812/
Should help with #33505, #29877 and maybe #47780, as there is no garbage
data at the end of transmissions on nRF52832, and no gaps.
Signed-off-by: Jonathan Rico <jonathan@rico.live>
STM32L4plus mcu has SDMMC internal DMA which works without any
configuration and it's handled by SDMMC HAL driver. This commit adds
option to enable it and use it.
Signed-off-by: Petr Hlineny <development@hlineny.cz>
Create and use a new `zephyr,i2c-target-eeprom` compatible
within I2C eeprom target driver that allows to use
that driver along with real atmel at24 EEPROM simultaneously.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Update machine timer drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on NIOSV devicetree.
Signed-off-by: Khor Swee Aun <swee.aun.khor@intel.com>
This commit adds access to the string values without a quotes.
Signed-off-by: Radosław Koppel <r.koppel@k-el.com>
Co-authored-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
This commit adds support for BH1750 ambient light sensor.
The driver works using I2C peripheral in one-time mode.
Signed-off-by: Michal morsisko <morsisko@gmail.com>
The Microchip XEC (MEC172x and MEC152x) have a breathing-blinking
LED (BBLED) block which implements a simple PWM mode. The BBLED
PWM frequencies are 32KHz and 48MHz selectable in device tree.
Frequency divider is 12-bit resolution from 256 to (256 * 4096).
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The Microchip XEC family of microcontrollers includes a
simple DMA block implementing multiple channels. DMA supports
memory to memory, memory to peripheral, and peripheral to
memory transfers. Peripheral support is limited by each
chip to I2C and SPI controllers. DMA hardware does not support
scatter-gather or linked transactions.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Align driver with changes introduced in the hal. `nrf_timer_frequency_set`
was changed to `nrf_timer_prescaler_set`, update driver accordingly.
Signed-off-by: Adam Kondraciuk <adam.kondraciuk@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
New Zephyr WDT driver for TI CC13xx/CC26xx family.
Supports interrupts & MCU soft reset on timeout.
Signed-off-by: Stancu Florin <niflostancu@gmail.com>
Each GPIO controller may contain GPIO hog definitions. GPIO hogging is a
mechanism for providing automatic GPIO configuration during system
initialization.
Each GPIO hog is represented as a child node of the GPIO controller.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
changes to support low power and wake support in microchip xec uart
driver. Add support for wakerx_gpio config in dts to select the wake gpio.
Configure for wake in PM_DEVICE_ACTION_SUSPEND state and clear
interrupt in wake isr. Also added support for
CONFIG_UART_CONSOLE_INPUT_EXPIRED
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Boolean properties for STM32 ADC internal channels are not used anymore
and can be removed. It is replaced by channel number properties.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add some bindings to define STM32 ADC internal channels for:
- Temperature
- Vref
- Vbat
The goal is to transfer information to the dts instead of inside the
ADC driver.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Bugfix for the Cyclone V SoC DK ethernet driver need to add emac-index
in dts
- We remove the "local-mac-address" property from
dts/arm/intel_socfpga_std.dtsi to
boards/arm/cyclonev_socdk/cyclonev_socdk.dts, since this value is
dependant on the board / implementation and not universal to
the "intel_socfpga" package that it inherets from.
- The above is also true for the "status" property as the board
should enable the device.
Signed-off-by: Benjamin Kyd <benjamin.kyd@intel.com>
Add three xbar nodes and four qdec nodes in the rt10xx devicetree include.
Add xbara to rt1052 in Kconfig.soc
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add a driver for the NXP MCUX Quadrature Decoder. The driver
is simple and only implements the phase a and phase b inputs. The
module has additional features which can be added in future PRs.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Change the name of the custom macro defined for the stm32 devices
to fit the VND_PWM_xxx model
Keeping old deprecated macro, though.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Introduce Ethernet low-level driver for NXP S32 Network Controller
(NETC). Current driver allows to manage from Zephyr a Physical Station
Interface (SI) and/or a Virtual SI. The NETC has an integrated Ethernet
Switch. Currently the Switch is initialized from this driver with a
default configuration, and all ports are enabled and transparent for
the user. A separate Switch driver should be addressed in future patches.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Introduce NXP S32 NETC External MDIO controller driver. Driver supports
a single instance, as current support is based on NXP S32Z/E SoCs.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Introduce NXP S32 Message Receive Unit (MRU) driver based
of Mbox API. The MRU couples with a processor and allows to
receive messages from senders, which are other modules or
processors.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Add 2 properties in STM32 external interrupt controller:
- num-lines
- line-ranges
Additionally, make interrupt-names a required property.
The properties will help to simplify exti init code in building the
exti_irq_table and simplify the isr related bits.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Intel DSP Communication Widget is a device for generic sideband
message transmit/receive between IPs in a SOC.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
The interrupt is used to wake up EC from low power mode.
So EC does not defer eSPI bus while transaction is accepted.
Fixes EC host commands slow issue.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
This commit makes the peripheral-id property optional and removes it's
usage from the Gecko SPI driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
The documentation for the fixed-partitions binding is missing critical
information and is vague in other important respects. This is an
important binding that deserves to be crystal clear. Fix it.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Add kscan pins gpio driver for KSI[7:0], KSO[15:0] pins that
they can be configured to gpio mode. These pins registers address,
bit fields and function are different from GPIO group, so I create
a new compatible driver for these pins.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
- Adds the declaration of the MMC API
- Adds MMC spec related declarations
- Adds some properties to sdhc dts binding for mmc
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
- Adds the pin controls and ushdc settings in device tree
- Attaches clock to USDHC in soc.c
- Adds binding for mmc
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
While nPM1100 is to be operated in fixed configuration for some
applications, it has some degree of configuration via GPIOs. For
example, mode (auto/PWM) can be configured via MODE pin. VBUS current
can also be adjusted using ISET pin, even though there is no API yet to
limit the PMIC input current.
This patch adds a new regulator class driver for nPM1100 PMIC, so that
it can be used with the standard regulator API when needed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit adds the support for host commands being transported
by the Serial Host Interface on the IT8xxx2 SoC.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
This commit adds the support for host commands being transported
by the Serial Host Interface on the NPCX SoC.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
Adds a driver for TDK InvenSense 42688 six axis IMU. Verified using
the sensor shell sample app via:
- sensor info
- sensor get icm42688p@0
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Signed-off-by: Yuval Peress <peress@google.com>
Add a st,static-prescaler optional property to DTS
of the stm32 where the LPTIM has a x2 factor on
its clock input.
This property is present or not depending on the stm32.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Drop compatible from fuel-gauge.yaml, it's not needed since this binding
is not meant to be used directly, and is also incorrect as it includes
the "yaml" suffix.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Purpose of this node is only to provide a way to configure RF
clock using device tree and clock_control driver.
Default configuration is reproducing existing hard-coded configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Introduce driver for APS6408L PSRAM, built on top of the MCUX memc
driver for flexSPI. This driver supports operating the PSRAM in high
speed mode (200MHz or more). Note that in order to support this
PSRAM's alignment requirements, either ahb-read-addr-opt or
ahb-prefetch must be set for the FlexSPI instance.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Rename flexspi-hyperram driver to flexspi-s27ks0641, and update
function names. This driver is only capable of supporting the
s27ks0641 HyperRAM chip, as the lookup table given in this driver
is specific to the s27ks0641.
Rename the flexspi-hyperram binding to reflect this, to
prevent confusion from users.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fix all line-length errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(line-length)'
Using a limit is set to 100 columns, not touching the commandlines in
GitHub workflows (at least for now).
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix all comments-indentation errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(comments-indentation)'
This checks that the comment is aligned with the content.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix all hyphens errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(comments)'
Default config would be to require two spaces after the start of the
comment, proposing to keep it on 1, inline with the Linux binding
config, that is:
```
- comments:
- min-spaces-from-content: 1
```
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix all hyphens errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(hyphens)'
Default config is only one space after the hyphen.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix all brackets errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(brackets)'
Default config is to have no spaces inside brackets, changed few
documentation strings as well that refered to lists even though the
linter does not care about those.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix Microchip XEC clock control driver single-ended XTAL2 pin
initialization. Add support for external 32KHZ_IN pin as a
clock source including PINTRL to switch the GPIO to 32KHZ_IN
function. Add device tree option to disable internal silicon
oscillator if it is not required by the configuration. Add
device tree tuning options based on crystal and board layout.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add config cell property to gd,gd32-dma.
For supporting hardware variation, Splitting base definition
to gd,gd32-dma-base.yaml.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
peripheral-id property should be eventually removed.
For now set it as optional and allow skipping the usage
in UART driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
peripheral-id property should be eventually removed entirely.
For now set it as optional and allow skipping the usage
in GPIO driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
This commit adds initial support for Silabs Real-Time counter
Co-authored-by: Filip Kokosinski <fkokosinski@antmicro.com>
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
This commit adds a series of driver-related changes to
Gecko pinctrl.
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds initial support for gecko pinctrl driver
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The ADC module has four conversion groups, each one is set up as a zephyr
device. The start-up calibration is initiated globally for all groups
and it is run in each device init function. The ADC module supports post
calibration per group. Post calibration is run automatically after each
group acquires the samples.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Add FFF-based fake regulator driver. This driver can be used as a stub
or mock in testing.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
These inherited properties from Linux bindings are not supported yet.
The reason for the removal is because regulator-couple-with requires
definition of #cells spec, unless bindings explicitely ban the property
or use allowlist.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add support for virtual USB host controller intended for use
together with virtual bus and virtual device controllers.
This driver is not an emulation of any real host controller.
The driver has initial support for handling control and bulk
transfers.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add support for virtual USB device controller intended for use
by virtual bus and virtual UHC controllers. This driver is not
an emulation of any real host controller.
The driver has initial support for handling control and bulk
transfers.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add common layer of UHC API and MAX3421E host controller driver.
This implements the bare minimum necessary to communicate with
one peripheral device.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Support for the measuring the CPU die temperature
for the ESP32 targets S2,C3. The ESP32 support
was ommited due to lack of offset calibration.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Serial speeds listed in device tree did not reflect
what driver supports.
2M and 500K were missing while
1200, 2400 and 460800 were present while not supported.
This change synchronized dts with driver code:
drivers/serial/uart_smartbond.c
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
PCA9420 PMIC offers of multiple operation states, or DVS (Dynamic
Voltage Scaling). Such states may be automatically changed by hardware
using MODESEL0/1 pins. Certain MCUs allow to automatically configure
certain output pins when entering low power modes so that PMIC state is
changed without software intervention. This means that application just
needs to configure the voltages for each state using
`nxp,modeN-microvolt`, set `nxp,enable-modesel-pins` in devicetree and
forget about configuring regulators.
This patch introduces a new _parent_ API to expose such functionality in
a vendor agnostic way. Consider this API as experimental for now, until
we have other usecases.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Most of devicetree properties for regulator, such as:
- regulator-min/max-microvolt
- regulator-min/max-microamp
- regulator-allowed-modes
- etc.
Are meant to specify limits on what consumers may set. They are **NOT**
meant to describe the hardware capabilities. For example, I could have a
BUCK converter that supports 0-5V output voltage, but my circuit may
only allow working on the 2.7-3.3V range.
This patch reworks the API so that the API class layer manages this
information. This is done by drivers collecting all such fields in a
common configuration structure that is later accessed by the class
layer. This simplifies drivers implementation. For example, if A
consumer calls regulator_set_voltage() with a voltage that is supported
but not allowed, driver code won't be called. Similarly, if a regulator
is configured to be `always-on`, enable/disable driver code will never
be called.
Drivers have been adjusted. PCA9420 mode settings have been removed from
devicetree in this commit as they are not actual modes but PMIC states.
This will be refactored in a follow-up commit.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The XY Memory is a feature commonly found in DSP processors to increase
the DSP performance. The XY component allows a ARC processor to
implicitly load source operands and store results into a closely coupled
memory using a single instruction.
Add XY memory for ARC EM9D/EM11D processors including em_starterkit,
em_starterkit_em11d. emsdp_em9d, nsim_em, iotdk.
Signed-off-by: Siyuan Cheng <siyuanc@synopsys.com>
In Infineon XMC4XXX SoCs, gpio interrupts are triggered via an
Event Request Unit (ERU) module. A subset of the gpios are
connected to the ERU. The ERU monitors edge triggers and creates
a SR.
This driver configures the ERU for a target port/pin combination
for rising/falling edge events. Note that the ERU module does
not generate SR based on the gpio level. Internally the ERU
tracks the *status* of an event. The status is set on a positive
edge and unset on a negative edge (or vice-versa depending on
the configuration). The value of the status is used to implement
a level triggered interrupt; The ISR checks the status flag and
calls the callback function if the status is set.
The ERU configurations for supported port/pin combinations are
stored in a devicetree file dts/arm/infineon/xmc4xxx_x_x-intc.dtsi.
The configurations are stored in the opaque array
uint16 port_line_mapping[].
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
The interrupt-map property specifies both 32-bits values and a phandle;
update the type accordingly.
Update the definition of pcie-host-ecam-generic on qemu arm64 to match
the new type.
Signed-off-by: Rodrigo Cataldo <rodrigo.cataldo@huawei.com>
Co-authored-by: Henri Xavier <datacomos@huawei.com>
Add DTS information for qemu-virt-a53 and qemu-kvm-arm64 for PCIe
controller support. Three new bindings are required for the PCIe
controller in ECAM mode.
The DTS information was extracted from QEMU (dumpdtb) with a PCIe device
attached to the virtual machine (ivshmem)
Signed-off-by: Rodrigo Cataldo <rodrigo.cataldo@huawei.com>
Co-authored-by: Henri Xavier <datacomos@huawei.com>
We are about to add UART reset during driver initialization. First step
is to add 'resets' property, which provides information about reset
register offset and bit.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
We are about to add timer reset during driver initialization. First step
is to add 'resets' property, which provides information about reset
register offset and bit.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
To deassert reset in STM32MP1 RCC the driver needs to set the bit in
reset clear register.
This patch extends existing implementation to support this type of
register.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
This driver exposes STM32 RCC reset functionality through reset API.
Information about RCC register offset and bit is encoded just like GD32.
The first 5 least significant bits contains register bit number.
Next 12 bits are used to keep RCC register offset. Remaining bits are
unused.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
STM32 battery-backed RAM is organized in 4 byte registers. Number of
registers can vary between models from 5 to 32 registers.
Usually, the registers are part of RTC. On some variants they are part
of tamper module. On STM32F1 the registers are in separate module. For
now, only backup registers from RTC are supported.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
NXP LPUART IP supports rs485 mode when transceiver driver enable
using RTS. Allow setting rs485 mode up via the "nxp,rs485-mode"
dts property. "nxp,rs485-de-active-low" dts property can be used
for set RTS polarity.
Signed-off-by: Grixa Yrev <GrixaYrev@yandex.ru>
- Similar to what was done for other parts of the driver, remove any
register specification from Devicetree (modesel-reg/mask)
- Keep all the information in the driver, and define modes as "numbers",
e.g. PCA9420_MODE0: 0, PCA9420_MODE1: 1, etc.
- Bindings provide IC defaults now (all modes allowed 0/1/2/3 and
initial mode set to 0).
- When mode is controlled via the MODESEL0/1 pins (ie directly by an iMX
MCU using the dedicated PMIC_MODE0/1 pins), the driver will not allow
to select a mode (it is not possible). This mode is now enabled by
setting `nxp,enable-modesel-pins` in Devicetree. When enabled, all the
allowed modes are configured to be selectable via pins. When disabled,
mode can be set via I2C (using TOP_CNTL3 MODE0/1_I2C fields)
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add bindings for Aspeed AST10x0 reset driver. The reset line can be
de-asserted or asserted through the syscon registers.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Add RX and TX fifo size properties to CDC ACM UART bindings.
This allows per instance settings in contrast to Kconfig
USB_CDC_ACM_RINGBUF_SIZE option. New properties takes the default
size value of USB_CDC_ACM_RINGBUF_SIZE which can be removed
subsequently.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add rgb-is-inverted option to indicate module's pixel-format is
inverting from MADCTL settings of ST7735R controller.
This option intends to implement a workaround for LCD modules
that is the actual screen color was different (inverted)
from the RGB setting in MADCTL property.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Implement a LED driver for Microchip XEC using the breathing,
blinking LED controller. The driver supports LED on, off, and
blink API's. The BBLED block uses the 32768 Hz clock domain
allowing the module to operate in light and deep sleep states.
Blink frequency is 32768 divided by 256 * (prescale + 1) where
prescale is a 12-bit value. Duty cycle is specified by an 8-bit
value where 0 = full off, 127 is 50%, and 255 is full on.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove regulator-fixed-sync specialization, create a single driver that
is always synchronous. The asynchronous part is rarely/never used, so
let's keep things simple for now.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
NXP S32 System Timer module includes a 32-bit count-up timer and four
32-bit compare channels with a separate interrupt source for each
channel. The timer is driven by the module clock divided by an 8-bit
prescale value.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Microchip XEC GPIO pins support inverting the output of
alternate pin functions. This feature may be useful for
those peripherals that do not implement output inversion
in the peripheral. GPIO control register pad input and
parallel input register values are not affected by the
function output invert feature. GPIO interrupt detection
of an output is inverted if the invert polarity is enabled.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
add Intel HDA DAI driver
Long device list in dtsi needs to be refactored in the future
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
The driver had a conceptual issue regarding current limitation. PCA9420
is able to limit the current flowing through VIN, ie input current. This
is a global setting, not individual to each regulator. This patch
creates a new DT property: nxp,vin-ilim-microamp to specify such limit.
It is applied when the device is initialized.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Voltage ranges were hardcoded in Devicetree, however, things can be
significantly simplified by using the recently introduce linear ranges
API. All values are now computed using information stored in the driver,
so there is no need to store any lookup table in ROM. Code should now
both be faster in average and consume less ROM.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Maximum current was not specified. Even though not used, yet, it is a
valuable information. Values taken from PCA9420 datasheet, Figure 1
"Simplified block diagram".
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Regulator registers were set for each BUCK/LDO in DT, likely because of
the way the devices were instantiated. When using a generic iterator,
ie, DT_INST_FOREACH_CHILD, there's no way to differentiate the child
being _parsed_. Since instantiation happens now based on child node
names, we are able to know which registers each devices gets assigned at
the driver level. This greatly simplifies Devicetree, and it actually
removes information that is not strictly hardware description from it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Right now the PCA9420 driver instantiates by iterating over all
children. This is somewhat problematic, for a few reasons:
- Since instantiation is generic code, we're forced to put internal
details on Devicetree, e.g. reg-masks. After this change, this will no
longer be necessary.
- We take all children, regardless of what is defined in DT.
While we have no means to validate Devicetree node names as in Linux
dtschema, this approach allows us to have per-child specific
initialization code. This is somewhat similar to the Linux approach.
Note: nodelabels have been removed, since they were not used.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
regulator-allowed-modes/regulator-initial-mode are standard properties
defined in regulator.yaml, so use them.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Import all Linux properties, so that we can maximize compatiblity with
upstream bindings.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Following Linux regulator.yaml, regulator-name is a common property for
all regulators.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The sdhc-spi-slot requies an spi bus, but sd nodes (like sdmmc-disk)
cannot be added to it without a warning because it does not declare an
sd bus.
Signed-off-by: JP Sugarbroad <jpsugar@amazon.com>
RT1718S is an i2c-based TCPC chip that supports 3 additional GPIOs.
The pins can be used for USB-C operations e.g. handling FRS, but they
can also work as usual GPIOs.
Add a driver for the RT1718S GPIO and a handler for an alert signal from
the chip. The handler reads the alert register once asserted and calls
the GPIO interrupt handler if needed(Vendor-defined alert).
gpio_rt1718s.c file and "richtek,rt1718s" node collect common properties
and data for all RS1718S functionalities. The file can be extended for
TCPC driver. rt1718s.h file also defines inline functions with i2c
operations common for all drivers. The common header and source files
can be moved to tcpc directories once the tcpc driver is added since it
is the main functionality.
Signed-off-by: Dawid Niedzwiecki <dn@semihalf.com>
Add drdy_pulsed property in Device Tree in order to select how
data ready irq should behave (either pulsed or latched mode).
Moreover change/fix the API called to set drdy irq mode.
(fix#51944)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Since we can include other binding files at any level (child,
grand-child, etc.) it makes no sense to maintain two copies of pinctrl
props definitions (pincfg-node/pincfg-node-group). Instead,
pincfg-node.yaml defines props at root level, and it is included where
needed, either child-binding or grandchild-binding.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Added to the device tree values of the dma-copy-alignment
and dma-buf-size-alignment attributes.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
dma-buf-size-alignment: Buffer size alignment required by the DMA
controller.
dma-copy-alignment: Minimal chunk of data possible to be copied
by the controller.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Renamed the dma-buf-alignment field to a more explicit
and descriptive name dma-buf-addr-alignment.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
No sfdp-table property given by the DTS but received from
the octoflash Node rely on the issued by the read sfdp command.
Note that the size of the mx25lm51245 flash controller
is expressed in bits (ie 512Mbits or 64 Mbytes).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
DTS property attributes are (by default) not required.
Explicitly specifying `required: false` is redundant.
Perhaps a warning to that effect would be useful.
Signed-off-by: Chris Friedt <cfriedt@meta.com>
Add a sample sbs gauge driver with feature parity and basic tests
comparison to its sensor counter-part. Includes a simple stub test that is
extended upon.
Signed-off-by: Aaron Massey <aaronmassey@google.com>
Added support for fxas21002 sensor over SPI bus on
RDDRONE board and proper selection through dts.
Tested with fxas21002 sensor on RDDRONE.
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Co-authored-by: Sumit Batra <sumit.batra@nxp.com>
Added support for fxos8700 sensor over SPI bus on
RDDRONE board and proper selection through dts.
Tested with fxos8700 sensor on RDDRONE.
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Co-authored-by: Sumit Batra <sumit.batra@nxp.com>
Use the new PCIe core infrastructure for looking up the BDF at runtime
based on the VID/DID values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the new PCIe core infrastructure for looking up the BDF at runtime
based on the VID/DID values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the new PCIe core infrastructure for looking up the BDF at runtime
based on the VID/DID values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the new PCIe core infrastructure for looking up the BDF at runtime
based on the VID/DID values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the new PCIe core infrastructure for looking up the BDF at runtime
based on the VID/DID values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BDF values can differ on the same platform, based on e.g. BIOS
configuration, and in the case of qemu the command line parameters. It's
therefore more reliable to always look up the BDF value based on the
known Vendor and Device IDs.
This patch introduces such a framework, and allows the incremental
update of PCIe drivers to start taking advantage of it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add property mxicy,mx25r-power-mode to jedec,spi-nor binding for
controlling low power/high performance mode on Macronix MX25R* Ultra Low
Power flash devices.
- "low-power" configures the flash in ultra low power mode.
- "high-performance" configures the flash in high performance mode.
Signed-off-by: Gregers Gram Rygg <gregers.gram.rygg@nordicsemi.no>
Updating mps3_an547 board files with DTB entries for Ethos-U.
Adding DTS bindings for the Ethos-U DTB entry.
Signed-off-by: Kristofer Jonsson <kristofer.jonsson@arm.com>
Signed-off-by: Fredrik Knutsson <fredrik.knutsson@arm.com>
The sensor uses the ALERT terminology (pin can be configured to trigger
on certain events such as conversion ready or overvoltage alerts). The
"IRQ" name is not clear.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify the units of the current LSB in microamperes, so that we can
measure low maximum currents. Right now it was specified in
milliamperes, but ignored and always hardcoded to 1mA in the driver.
This makes the driver pretty much useless when the maximum current to be
measured is in a range of e.g. 20-50mA.
This patch also removes some unnecessary ifdeffery: since we write the
calibration register, we can always provice measurements with the right
units. It is also wrong to provide sensor readings that do not match
with the units specified by the channel. After this change voltage is
always reported in V, current in A and power in W.
Note that power measurement had the current LSB hardcoded in the
calculation (assuming 1mA/LSB), this has been fixed as well.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Following dtschema practices, add phyisical units to the shunt resistor
value: milliohms.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The "pmic" driver was in reality a driver for NXP PCA9420 PMIC. There's
no "universal PMIC". While the driver may work for other NXP PMICs, it
is clearly not generic for other vendors PMIC.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Force cache-size to 0 and treat flashdisk as read-only when backing
partition has read-only flag set. This allows users to save RAM when the
application does not write to the flashdisk, e.g. when a predefined FAT
filesystem is used.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Ensure that PECI block is enabled in the EC Subsystem by clearing
the PECI_DIS (peci disable) register
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Following the modification of the STM32 OSPI driver, the clock-names
binding is now required
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
The icmsg backend for ipc_service has a limitation of supporting only
on endpoint. This limitation is acceptable for many IPC instances.
However, some require to use multiple endpoints sharing a single
instance. To preserve the simple and the most efficient single-instance
backend, a separated backend is introduced implementing a wrapper
around icmsg core which adds multiple endpoints support.
There are two multi-endpoint ipc_service icmsg backends: one in the
initiator role, and the other one in the follower role. In a IPC
configuration one end of communication must be in the follower role
while the other one is in the initiator. The initiator initiates
an endpoint discovery handshake to establish enpoint identifiers for
requested endpoint names. The follower responds to requests sent by
the initiator.
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
For larger transfers DMA can be used enabling other tasks
to continue running. A threshold of 32 byte transfers
is about right and is defined threshold value for using DMA.
This does not currently support multiple SPI transactions changing
chip select with DMA (though the hardware supports this) currently.
Instead opting for the simpler first change of enabling one shot
DMA SPI transfers for those where the size warrants it.
Adds the loopback binding option to enable the spi_loopback test.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add support input interrupts for GPIO pins on NXP S32Z27
SoC. The driver will convert GPIO pin to respective
interrupt line that will be processed by External
Interrupt Controller.
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Add initial support for the NXP S32Z27 SIUL2 External
Interrupt Controller. Each SIUL2 node has a child node
will act as an interrupt-controller that processes external
interrupt signals.
This driver is required to manage GPIO interrupts.
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
New ADC driver for the TI CC13xx/CC26xx family.
ADC channel configurations are translated from Zephyr constants to
simplelink driverlib ones (e.g., sample times use a lookup table).
Async mode was also implemented & tested.
Signed-off-by: Stancu Florin <niflostancu@gmail.com>
Adds Atmel SAMC20 and SAMC21 soc. C series is based on Cortex-M0+.
C21 contains CAN interface.
The init routines are same for SAMC20 and SAMC21. They use one
clock OSC48M without configuration.
The code is inspirated from atmel_sam0/samd21.
Signed-off-by: Kamil Serwus <kserwus@gmail.com>
This commit adds an optional property to the nRF21540 Front-End Module
devicetree description that specifies supply voltage in mV. This
property can be used by the nRF21540 driver to compensate the value of
achieved gain for different supply voltage.
Signed-off-by: Artur Hadasz <artur.hadasz@nordicsemi.no>
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Add SparkFun Pro Micro header connector that is implemented by many
other controllers. This allows hardware with compatible headers to
define the related GPIOs and peripherals.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
The ESP32 series MCUs allow to set a timeout which triggers an error
if the SCL line is unchanged for the specified amount of time.
By default, the ESP-IDF HAL sets the timeout to an arbitrary value of
10 times the bus cycle.
This is not sufficient for chips like the TI bq76952, which pulls the
SCL line low (clock stretching) for several 100 µs.
The timeout should also not be dependent on the chosen bitrate, as it
is defined by the time a chip needs for internal calculation before it
can provide requested data or continue communication.
This commit adds a property to devicetree to allow configuration of
the scl timeout. This value is set via direct register access, as the
ESP-IDF HAL does not provide access to the enable bit and does not
give any information about the maximum size of the timeout (defined
in I2C clock cycles in the register).
Fixes#51351
Signed-off-by: Martin Jäger <martin@libre.solar>
Microchip MEC172x has a modified eSPI SAF hardware implementation.
Hardware changes include multiple clock dividers for each SPI
flash device and data transfer using QMSPI local DMA.
espi reset interrupt is made a higer priority in MEC172x devicetree
because espi reset event resets all espi hardware and we don't
to want to service any other espi interrupt blocks when espi reset
occurs.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add bindings to describe a block storage device based on flash map
partition.
Co-authored-by: Johann Fischer <johann.fischer@nordicsemi.no>
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Add devicetree binding for the PSA Crypto Random source.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
This commit adds missing binding file for the ite,it8xxx2-usbpd.
Without this file, the DT_HAS_*_ENABLED macro wasn't defined and
couldn't be used in the Kconfigs.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
A USB TypeC connector has many peripherals associated with
it and the DTS binding in this commit provides a way to group
peripherals and properties in a device tree.
This binding is used with the USB-C Subsytem.
This is based on Linux, documentation:
https://www.kernel.org/doc/Documentation/devicetree/bindings/connector/usb-connector.yaml
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Add pin control properties to the STM32 UCPD bindings file so that
the pins can be configured in the device tree.
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Executing code out of RAM on IT8xxx2 requires that the relevant
addresses be mapped onto the CPU's instruction memory bus, referred to
by ITE documentation as Instruction Local Memory (ILM). ILM mappings
configure blocks of RAM to be used for accesses to chosen addresses when
performing instruction fetch, instead of the memory that would normally
be accessed at that address.
ILM must be used for some chip features (particularly Flash
self-programming, to execute from RAM while writing to Flash), and has
historically been configured in the Flash driver. The RAM for that was
hard-coded as a single 4k block in the linker script. Configuring ILM
in the flash driver is confusing because it is used by other SoC code as
well, currently in code that cannot depend on the Flash being functional
or in hand-selected functions that seem performance-critical.
This change moves ILM configuration to a new driver and dynamically
allocates RAM to ILM in the linker script, allowing software use of the
entire 64k RAM depending on configuration. This makes ILM configuration
more discoverable and makes it much easier to correctly support the
CODE_DATA_RELOCATION feature on this SoC.
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
USB interface that may be used to send messages from a USB host to
the M4 processor in the S3B, and vice-versa.
Signed-off-by: Michal Sieron <msieron@antmicro.com>
Add support for regulator-boot-on to PMIC driver. Many PMIC devices will
be enabled at boot, so this property allows the regulator framework
to correctly track their state.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
As part of a previous refactor, this property was removed from the STM32
USART binding. The driver code to support this feature was not changed.
This commit simply adds the property back to the new base .yaml for
device trees which used it.
Tested on a proprietary board using the STM32U5 on USART1.
Signed-off-by: Peter Maxwell Warasila <madmaxwell@soundcomesout.com>
Migrates all Winsen sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all WE sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Vishay sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all TI sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ST sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Silabs sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Sensirion sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Semtech sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Seeed sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all SBS sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Plantower sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Panasonic sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all NXP sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Nuvoton sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Nordic sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Microchip sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Measurement Specialties sensors to inherit base sensor
device properties. This will allow us to define properties shared by
multiple sensors in one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Maxim sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all LM sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ITE sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Intersil sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Invensense sensors to inherit base sensor device
properties. This will allow us to define properties shared by multiple
sensors in one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Infineon sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all HOPERF sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Honeywell sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Espressif sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Bosch sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Avago sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Atmel sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Asahi-Kasei sensors to inherit base sensor device
properties. This will allow us to define properties shared by multiple
sensors in one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Aosong sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all AMS sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ADI sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Introduces an initial set of devicetree properties to be inherited by
all sensor devices, similar to how we define a base set of devicetree
properties for I2C and SPI devices. These properties will be used by the
future sensor subsystem to manage and expose sensors to a host operating
system, through HID or another protocol. Additional properties may be
added in the future.
An earlier version of this patch attempted to use the label property
instead of friendly-name, as it was noted during code review as a
possibly legitimate usage of the mostly-deprecated label property.
However, in practice it was difficult to implement because most sensor
bindings also inherit from i2c-device.yaml or spi-device.yaml, and
therefore inherit the deprecated label property from base.yaml. To work
around the deprecation, every sensor binding would have needed to
explicitly block the label property with a property-blocklist, which
would somewhat defeat the purpose of having a shared sensor-device.yaml.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Add MEC172x full duplex qmspi driver version to support full
duplex transfers as expected by the Zephyr spi driver model.
On every spi clock we transmit one bit and receive one bit.
This driver will work with Zephyr SPI NOR driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
updated dts variables naming (hyphen instead of underscore).
moved all properties in microchip ldma yaml to a separate include file,
these properties will be common with the (to be added)
full duplex spi driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Newer ESP32 series MCUs like the ESP32-C3 contain some register changes
incompatible to the original ESP32 and the SJA1000.
The additions in this commit consider these changes and fix the
incompatibilities in the TWAI front-end for the SJA1000 driver.
Signed-off-by: Martin Jäger <martin@libre.solar>
Implement GPIO driver minimal API's for NXP S32 devices, based on SIUL2
peripheral. SIUL2 allows to control the pins electrical characteristics
such as internal pull resistors, pin direction and more.
GPIO driver API's for interrupts will be implemented in a future patch.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
This patch introduces support for NXP S32 LINFlexD peripheral operating
in UART mode. Polling and interrupt-based serial API's are supported.
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Introduce Pinctrl driver for SIUL2 module present on NXP S32 devices,
which provides control over all pins, such as function selection and
electrical characteristics that appear on external chip pins.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Add mode selection properties for regulator-pmic compatible. These
mode selection properties will be used with regulators that support
multiple modes, with each mode enabling specific voltage and current
limits.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Refactor binding to use root PMIC IC, so that properties can be shared
between regulator devices. Each individual regulator output is still
created as an individual device, since the regulator API aligns with
these devices better than the PMIC IC itself.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Convert timer driver to use a light weight syscon and DTS and convert
register information to use offsets and sys_read/sys_write instead of
structs.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some windows might need to be set as writtable, so add a flag read-only
to DTS bindings which is set to true for all windows right now. This can
be set to false where needed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Instead of just declaring the memory window register in DTS and have
everything else all over the place (headers, Kconfig, etc.) this change
defines the memory window instances in DTS and uses the device model to
initialize the windows. Code is still part of the SoC, given that we do
not have a driver subsystem suitable for this type of device yet.
Move FW status to own workflow and separate from window setup.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If the flash is used in 4-byte addressing, reading SFDP will fail after
a system reset if the flash isn't power cycled or hardware reset, since
Zephyr will try to use 3-byte addressing while the flash (still) expects
4-byte addressing.
This commit adds the ability to send a reset command to the flash as part
of initialization, which complements the existing reset-gpio
functionality, and is useful on low-pincount flashes which do not have a
hardware reset.
Signed-off-by: Ole Morten Haaland <omh@icsys.no>
Added support for the AMS AS621x series of temperature sensors as a
variant of the TI TMP108 temperature sensor.
Signed-off-by: Jared Baumann <jared.baumann8@t-mobile.com>
Signed-off-by: James Johnson <james.johnson672@t-mobile.com>
Adding ethernet in the DTS file and corresponding binding
for Cyclone V SoC FPGA board..
Signed-off-by: Esteban Valverde <esteban.valverde.vega@intel.com>
Add a fifo address as int value into dmic yaml to separate different
outputs (corresponds to different dais) from the same hw block. Also
change shim address from array to int value.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Replace the hardcoded kPWM_Prescale_Divide_128
driver prescaler with the ones defined in the dtsi file
that allow overriding them by the user.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
This commit adds a driver to simulate GPIO state and interrupts
using the keyboard when using SDL.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Add 2 properties to configure the "any movement" event.
* Ability to disable the interrupt latch
* Select movement mode
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Include files should not have compatible properties set. These do not
represent real hardware and should therefore not appear to do so, e.g.
by appearing in the bindings index as if they were a real hardware
peripheral.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 qmspi. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 adc. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 pwm. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 espi. Update board dts, pinmux and espi driver
files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The FULLDRIVE description on the rt-iocon yaml file was
describing the slew rate and not the FULLDRIVE property.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
When the EXTI Line nb is not set as interrupt by default
(at reset value), the uart instance cannot waekup the
system from its low power stop mode.
The EXTI line must be specified, like with stm32WL55
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds a base binding for I3C controllers.
Note that this follows the Linux kernel 5.17 bindings under
Documentation/devicetree/bindings/i3c/i3c.yaml.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a few bits to the devicetree API tests for multi-bus
nodes where a bus can support multiple protocols. This uses
I3C as basis as I3C controller can support both I2C and I3C on
the same bus, while I2C controller cannot support both. So
this needs to make sure the correct bus macros are generated
if appropriate (and not generated if not needed).
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add support to at86rf212[b] sub-giga devices. This work enables use of
pages 0, 2 and 5 in accordance with IEEE-802.15.4/2003/2006/2011. The
proprietary speeds can be object of future work.
Note: It is recommended that user define a power table for better
performance, low emissions and to save power. A reference power table
can be found in the datasheet and should be used for tests only and
not on a final product.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The current version of power table is hardcoded in the driver which is a
problem when use devices in production. This change remove all hardcode
from driver and reimplement the feature to allow people create a table
which is defined in devicetree. The big advantage is that each board can
define their own table based on lab tests and allows use of FEM devices
inclusive.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The property is similar to the usb_controller_index_t
enum that is available in the NXP SDK.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
This commit introduces the 1-wire master driver for maxim ds2485.
The ds2485 master has nearly the same (1-wire) feature set and
i2c-interface as the ds2477.
Therefore the common parts are extracted, but to avoid
any nda troubles only the ds2485 specific part is included.
Compared to older 1-wire masters, the ds2485 supports higher level
commands, supporting multi byte operations, search next, automatic crc
calculation.
In this driver only basic read and write operations are supported,
further hardware features are not yet utilized by the driver.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This driver provides an interface to SocketCAN interfaces of the Linux
system running a Zephyr application with the native_posix board. These
interfaces may be virtual or actual CAN buses.
Signed-off-by: Martin Jäger <martin@libre.solar>
Migrate information to DTS and get it from there on the code. Note that
for CAVS 15, the information is not migrated as there's no DTS entry for
it. It can be brought back (in the DTS) if TLB support is enabled for
it.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Add emulator functionality to the serial_test driver, so that it can be
used to simulate a device on the other end of the uart.
If you don't set the buffer-size property in the dts node, there should
be effectively no change from the previous behavior.
Signed-off-by: Jeremy Bettis <jbettis@google.com>
Add the DMA in the DTS binding for OCTOSPI interface
for the stm32 devices from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
There are three types GD32 FMC.
GD32 FMC v1: its flash memory has 1 bank, page size is equal in the
bank, flash size is smaller than 512KB.
GD32 FMC v2: its flash memory has 2 banks. Page size equal within the
same bank but different between banks. Flash size can be up to 3072KB.
FMC v2 has two registers to control bank0 and bank1 separately.
GD32 FMC v3: its flash memory has 2 banks, use sector size as the
minimum operating unit, the sector size is not equal.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
Define RaspberryPi Pico ADC.
The ADC has internally connected temperature sensor,
Add property to enable this.
The ADC has a single VREF. VCC usually connects to it,
but it may not be in a case.
Add property to make configurable it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Use the clock control API to enable peripheral clocks. Note that both
GPIO and pinctrl drivers are updated at once since they share some IP
blocks.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Use the clock control API to turn on ADC clocks. Note that clock
selection is not yet implemented, so we still rely on custom rcu
properties for that.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This patch adds a clock control driver for GD32 platforms. It is
important to note that the driver is only able to handle peripheral
clocks, but not "system clocks" (e.g. PLL settings, SYS_CK, etc.). On
some similar platforms (STM32) this task is embedded in the same clock
driver, performed at init time but with no options to do any
manipulation at runtime via the API calls. The clock control API as-is
is really orthogonal to "system clocks", and it is arguably a bad idea
to embed system clock init code in a clock control driver. It can be
done at SoC level still using Devicetree as a source of hardware
description/initial configuration.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Remove the CAN_STM32FD_CLOCK_DIVISOR configuration option,
and add configuration via dts property clk-divider instead.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Changes to code:
1. Renamed CAVS_IPC API from common/include/cavs_ipc.h to
common/include/intel_adsp_ipc.h. Renamed all API functions and structs -
added "intel_adsp_" prefix.
2. Moved definitions from intel-ipc-regs.h and ace-ipc-regs.g to SOC
specific headers include/<soc_name>/adsp_ipc_regs.h.
3. Added new common intel_adsp_ipc_devtree.h header with new
macros to retrieve IPC and IDC nodes and register addresses.
Put those new macros in code replacing hardcoded values outside of
devicetree.
4. Changed documentation of IDC and renamed IDC register struct
to have common name between all intel adsp socs.
5. Removed excessive docs description on cAVS IPC protocol.
Changes to Devicetree:
1. Renamed in all CAVS boards .dtsi files content in IPC nodes:
- "cavs_host_ipc" node labels to "adsp_ipc" labels.
- compatible "intel,cavs-host-ipc" renamed to
"intel,adsp-host-ipc".
2. Added (previously missing) yaml file for "intel,adsp-host-ipc"
compatible.
3. Renamed in all CAVS boards .dtsi files content in IDC nodes:
- "idc" node labels to "adsp_idc" labels.
- compatible "intel,cavs-idc" renamed to "intel-adsp-idc"
4. Renamed intel,cavs_idc.yaml file to intel,adsp_idc.yaml
so it is suitable for both CAVS and ACE SoC family.
Moved it from ipm bindings to ipc bindings where it belongs.
Changes to Kconfig:
1. Renamed existing Kconfig option CONFIG_CAVS_IPC to
INTEL_ADSP_IPC.
2. For renamed INTEL_ADSP_IPC addded default value based on
status of the "adsp-ipc" and "adsp-ipc" node.
Signed-off-by: Andrey Borisovich <andrey.borisovich@intel.com>
Convert the device to be Devicetree based. Adjusted tests and other
areas that were using old Kconfig properties.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some custom refresh profiles need to set the PLL and VDCS
registers. Add them as optional DT properties.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Add support for overriding display LUTs in the UC81xx driver. This
makes it possible to use different LUTs for the full and partial
refresh profiles.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Add a separate profile for partial refreshes. This makes it possible
to specify a separate refresh configuration for partial and full
refreshes.
The driver now transitions to full refresh mode when blanking is
turned on. It transitions back to partial refresh mode when there is a
write while blanking is off.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Introduce the concept of refresh profiles which are specified as a
child node in the device tree. This makes it possible to use different
overrides for different types of refreshes (full/partial).
The only profile that is currently supported is the "full" profile.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
This patch is to add Cadence QSPI NOR flash device tree element
for the Cadence QSPI NOR flash driver bringup
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
This adds flash driver for Renesas SmartBond(tm) family.
This technically uses QSPI controller but since default and most
commonly used configuration is to boot from external QSPI flash (DA1469x
do not have built-in flash) and that flash is mapped into memory space,
it can be represented as internal flash.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
This adds serial driver for Renesas SmartBond(tm) family. Both polling
and interrupt APIs are supported.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
This adds GPIO driver for Renesas SmartBond(tm) family.
Driver supports pin configuration (input/output) and interrupts on edge.
Interrupts on level are not supported by hardware.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Add a new reset driver for GD32 platforms. This driver controls the
reset registers from the RCU peripheral. It can be used to restore
peripherals to their initial state when initializing a device.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
It was not possible to disconnect a pin using the nRF pinctrl driver.
That is, it was not possible to set PSEL to 0xFFFFFFFF (indicating pin
is not connected). This can be useful in certain scenarios, e.g. a
bootloader configures all signals of a certain peripheral but
application then needs to disconnect certain signals.
A new DT macro has been introduced to accomplish this:
NRF_PSEL_DISCONNECT. It can be used like this to explicitely disconnect
a peripheral signal:
```
&pinctrl {
uart0_default: uart0_default {
group1 {
psels = <NRF_PSEL(UART_TX, 0, 1)>,
<NRF_PSEL_DISCONNECTED(UART_RX)>;
};
};
};
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Despite being used in GD32 dts files, the compatible did not exist. Note
that there is no GD32 flash driver yet.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The TS_CAL values for the temperature sensor are measured on 12, 14 and
16 bit resolution depends on the STM32 series. Because the drivers
operates at 12 bit resolution the TS_CAL1 and TS_CAL2 must be divided.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
This commit defines a new dma version for devices like stm32U5.
The peripheral is a GPDMA in this soc serie.
It has several specific definitions used by its stm32 LL driver
compared to the V2, including up to 16 channels.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
There are 3 bindings for STM32 serial driver:
st,stm32-uart.yaml
st,stm32-usart.yaml
st,stm32-lpuart.yaml
Add a common st,stm32-uart-base.yaml that would be included by these
3 bindings an would group common properties.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
This commit adds string token versions of the values also
in items inside string-array.
Signed-off-by: Radosław Koppel <r.koppel@k-el.com>
Co-authored-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Co-authored-by: Kumar Gala <galak@kernel.org>
Add missing support for the triggered mode using GPIO
interrupt alert pin. It uses mode detection at runtime
which allows working multiple sensors with different
modes simultaneously.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
The new property nist-config is introduced to the stm32 mcus
to configure the RNG for NIST SP800-90B certification.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The gpio-leds binding is meant for LED drivers, not GPIO. As in Linux,
move the binding to the led folder.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
gpio-keys binding has been used in Zephyr to describe random push
buttons in boards. On Linux, it is used by a keyboard input driver,
while in Zephyr is, in most cases, used directly in applications out of
the device driver model. This should likely be _fixed_ if one day we
have a proper input device class. Still, we can align a few things:
- Inherit from base.yaml (we need status, compatible, etc defined there)
- Remove the requirement of a label in child nodes
- Fix child nodes label description
- Move to dts/bindings/input
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Don't import the label prop from base.yaml as it is marked deprecated.
This lets the various tests that still use DT_LABEL() to work properly.
Signed-off-by: Kumar Gala <galak@kernel.org>
Mark 'label' property as deprecated in base.yaml. 'label' is still
defined and valid for specific bindings to specify like gpio-keys.yaml
or fixed-partitions.yaml.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add spi0 and spi1 configuration to rp2040.
spi0 and spi1 are declared as compatible with
"raspberrypi,pico-spi" and "arm,pl022".
"raspberrypi,pico-spi" is just inherited from
"arm,pl022" and "reset-device"
spi0 and spi1 declare as compatible with "raspberrypi,pico-spi"
and "arm,pl022".
"raspberrypi,pico-spi" is just inheriting "arm,pl022" and
"reset-device" for declaring the 'reset' property,
with no additional property and implementation.
Add also pinctrl macros to dt-bindings header.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Add fundamental feature support for PL022 SPI peripheral.
This commit implements synchronous transfer with 8bit-MSB format.
Optional functions are not currently implemented yet.
- interrupt based transfer is not implemented yet.
- DMA transfer is not implemented yet.
- Slave mode is not implemented yet.
- Currently support only 8-bit data transfer.
Hardware limitation:
- LSB-first format is not supported by hardware.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
The binding 'nxp,lpc-iap' is no longer used, which is confirmed
by running:
$ find ${ZEPHYR_BASE}/dts/arm/nxp -type f | egrep -e '\.dts(i)*$' | \
xargs grep -nH nxp,lpc-iap
Changes in this commit:
- remove DT_HAS_NXP_LPC... in drivers/flash/Kconfig.mcux
- remove schema file for nxp,lpc-iap
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
The binding 'nxp,iap-lpc' is used for different flash controllers,
preventing clarity. This commit introduces bindings for each version of
the flash controller, as they appear with NXP lpc device families:
nxp,iap-fmc11: for the flash controler used on the lpc11u6x family
nxp,iap-fmc54: for the flash controler used on the lpc54xx family
nxp,iap-fmc55: for the flash controler used on the lpc55xx family,
except lpc553x
nxp,iap-fmc553: for the flash controler used on the lpc553x family
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
The SSD16xx driver currently hard-codes a couple of register overrides
that aren't relevant or even correct for many devices. Make them
optional device tree properties instead.
Note that this changes the behavior for panels that expect
SSD16XX_CMD_DUMMY_LINE and SSD16XX_CMD_GATE_LINE_WIDTH to be set by
the driver. This fixes a bug where the incorrect value
was written to all SSD16xx panels except for GDEH0213B1 and GDEH029A1.
The overlay files for devices that need dummy line and gate line width
to be specified have been updated as a part of this commit.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The OTP in most SSD16xx-based displays normally contain default
VCOM/GDV/SDV values. Make all of these optional in the device tree.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Add the option to specify the minimum duration that the `reset-gpios`
pin is held low on boot. This lets devices with additional capacitance
on the reset line still reboot the Bluetooth controller.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
This fixes underrun issues when hardware flow control can't be used.
Only tested on STM32F4.
Signed-off-by: John Kjellberg <kjellberg.john@gmail.com>
...
All the of the ITE it8xxx2 devicetree compatiables are of the form
ite,it8xxx2-<DEV>. However the PECI device was ite,peci-it8xxx2,
rename the compatiable to match the pattern used everywhere else.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add dts bindings for the NIOS2 QSPI controller and flash device and
add nodes to the dts files for these devices as well.
Signed-off-by: Kumar Gala <galak@kernel.org>
Fat finger mis-typed when I renamed the file last time.
So correctly name the file this time. Hopefully this is
correct and won't need anymore renaming... :(
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The current atmel sam flash driver was develop based on the cortex-m7
version of smart arm microcontroller. The driver support write
protection and cache functions which is not supported by other cortex-m
variants. This fixes current driver implementation and devicetree
entries for all sam variants.
Notes:
* The cortex-m3 doesn't have support erase pages flash command and
because of that the driver still not not compatible. Keep it disabled
until a patch be send. The hwinfo driver is not affected by this
restriction.
* The sam4l variation requires a specific driver because uses another
flash controller (flashcalw). Added another compatible to
differentiate and keeped node disabled until a driver be available.
Fixes#48516
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
() Fix the compatible string from "intel,dai,dmic" to
"intel,dai-dmic".
() Also rename the yaml file to have vendor name first.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use a test compatible so that test can create a DT-based device and
provide a valid choice when building the test.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to work on a clock speed higher than 20 MHz, IO MUX is required.
Co-authored-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Signed-off-by: XiNGRZ Chan <hi@xingrz.me>
various microchip bindings set 'girq-cells' and 'pcr-cells'
sections in the bindings. However the bindings where for the
client nodes and thus do not need to set these.
Signed-off-by: Kumar Gala <galak@kernel.org>
Change the wording about "alternate/optional" clock to "domain" clocks,
to better describe the feature and minimize confusion.
Additionally, provide more description about domain clocks and dual
domain functionality implemented in peripherals.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adds optional device tree property to specify a default character
to clock out when the TX buffer pointer is NULL. If the property is
not set the existing behavior (default char of 0x00) is used.
I verified the expected behavior using an i.MX RT685 board and
logic analyzer that the def-char character is transmitted when
TX buffer pointer is NULL.
Signed-off-by: Bryce Wilkins <bryce.wilkins@gmail.com>
LPC55s3x family has an additional analog mode bit available. Update
IOCON binding and IOCON driver to support setting this bit via a pin
control property.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Use Devicetree to describe the UART UPIPE IEEE 802.15.4 driver. This
allows to remove usage of IEEE802154_UPIPE_DRV_NAME in preparation for
the removal of NET_CONFIG_IEEE802154_DEV_NAME.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_NRF5_DRV_NAME in preparation for the
removal of NET_CONFIG_IEEE802154_DEV_NAME.
All SoC files have been updated with the addition of an ieee802154 node
(disabled and only on those SoCs that define ieee802154-supported. The
peripheral has been enabled in the nRF52840DK board (used for testing
ieee802154).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_KW41Z_DRV_NAME in preparation for the removal
of NET_CONFIG_IEEE802154_DEV_NAME.
KW41Z files have been updated with the addition of radio and an
ieee802154 nodes The peripheral has been enabled in the frdm_k41z board
(used for testing ieee802154).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_CC13XX_CC26XX_SUBG_DRV_NAME in preparation
for the removal of NET_CONFIG_IEEE802154_DEV_NAME.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_CC13XX_CC26XX_DRV_NAME in preparation for the
removal of NET_CONFIG_IEEE802154_DEV_NAME. All boards used in testing
have been updated to enable the peripheral in DT as well.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
ICI (Inter-Core Interrupt Unit) interrupts and priorities were hardcoded
in C files. This patch moves this information to Devicetree and updates
code to make use of it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
sysconf base address was hardcoded in <soc.h>. Create a new compatible
and define it in Devicetree, where hardware needs to be described.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Introduce a simple binding for atmel,24mac402 EEPROM that the SAM
GMAC ethernet driver can utilize to get MAC address out of. We
introduce a 'mac-eeprom' phandle into GMAC ethernet devicetree
node that will provide a pointer to the MAC eeprom to utilize.
Signed-off-by: Kumar Gala <galak@kernel.org>
The CLINT (Core Local Interruptor) description was not aligned with
Linux. For example, there's no "riscv,clint0", but "sifive,clint0". The
peripheral is not described as an interrupt-controller either.
Ref. https://elixir.bootlin.com/linux/v5.18.14/source/arch/riscv/boot/
dts/starfive/jh7100.dtsi#L106
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
After some analysis I found out that there's no machine timer provided
by the "riscv" vendor. There are some specs for the mtime/mtimecmp
registers (this is why we can have a single driver), but the actual
register layout or implementations differ amongst vendors. GD32 uses the
Nuclei implementation, named "system timer" in their documentation. This
patch aligns with vendor specs.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This adds a driver for Maxims DS2484 Single-Channel 1-Wire master
driver. The DS2484 features an extra pin to enable sleep modes which
is available if the pin is configured in the device tree.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Unlike stated in 57df225b396e43358aac4cc998ed2e99fdb57780, RM0456.pdf
reference manual mentions about PLL1R that "Only division by 1 and even
division factors are allowed."
Though, in reference manual, there is one issue on PLL1R values
description, which should actually be:
0000000: pll1_r_ck = vco1_ck
0000001: pll1_r_ck = vco1_ck / 2 (default after reset)
0000010: Not allowed
0000011: pll1_r_ck = vco1_ck / 4
...
This description will be fixed.
Reflect this in binding and driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Instead of enabling WOVCRO clock based on the SOC, use a configuration
to indicate support, so that each platform can specify if WOVCRO is
supported or not.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Add binding for Aspeed AST10x0 clock driver. The clocks can be turned
on or off through the syscon registers.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
The UC8176 and UC8179 chips that exist in tree have subtly different
register layouts. Use separate compatible strings for these chips and
a quirks structure that describe device-specific behavior.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The GD7965 driver is really just a vendor name for the UltraChip
UC8179. Rename the driver to UC81xx since there are other chips in the
family (e.g., the UC8176) with an almost identical register interface.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
For the !SOC_I2C_SUPPORT_HW_CLR_BUS in which we implement bus
reset via GPIOs, change the devicetree properties to be actual
gpio properties and update the code to reflect this.
Signed-off-by: Kumar Gala <galak@kernel.org>
This commit adds the pll2 and pll3 clock control nodes
with st,stm32u5-pll-clock compatible.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit changes the range for stm32u5 pll divider values
to allow divider value of 1.
- DIVQ is allowed to beconfigured 1 for all PLL instances
- DIVR can be 1 for PLL2 and PLL3, but is not valid for PLl1.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
We have drivers for "nxp,lpc-rtc" and "zephyr,native-posix-counter"
devicetree compatibles, however we had no bindings for them. Add
simple bindings
Signed-off-by: Kumar Gala <galak@kernel.org>
Two files ending with yml while the rest is ending with yaml, just
rename those two to avoid special handling.
Fixes documentation build.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This CL adds a DT node, 'power_leakage_io', which property,
'leak-gpios', contains GPIOs that have leakage current. In oerder to get
better power consumption, npcx power driver will disable the connections
between these io pads and input buffers before entering deep sleep.
Then, restore the connections after ec wakes up.
The users can overwrite this property at board DT file. Here is an
example:
&power_leakage_io {
leak-gpios = <&gpio0 0 0
&gpiob 1 0>;
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL configures low-voltage (1.8V) detection via GPIO driver with
GPIO_VOLTAGE_1P8 flag. It also adds support for this flag in
pin_get_config() function.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Cleanup npcx low-voltage (1.8V) detection configuration. It removes
unused soc utilities, macros, and DT node. We will configure this
feature by GPIO driver with GPIO_VOLTAGE_1P8 flag later.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Move the RX (MISO) delaying capability information to Devicetree. It is
done using 2 properties:
- rx-delay-supported: enabled on SPI nodes that support delaying RX.
This property can be used by the driver to determine if this
capability is supported or not on a given instance.
- rx-delay: the actual RX delay value
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify the overrun character in Devicetree. Since 0xFF is the most
common value, DT property contains such default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Devicetree is the natural place to describe hardware, so move the
maximum frequency the SPI can work with to Devicetree instead of relying
on values from HAL.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some panels using this driver don't provide tcon/cdi/pwr/softstart
values in their reference code. It is normally expected that the right
values will be loaded from OTP in such cases. Make these values
optional to support such panels.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add configuration for SPI connected ADXL345 accelarator sensor
as adi,adxl345-spi.yaml.
Rename original adi,adxl345.yaml that configured for I2C
rename to adi,adxl345-i2c.yaml.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Implement support for SAML21 parts, tested on a SAML21 Xplained Pro dev
board. Confirmed operational peripherals: UART, GPIO, PWM, ADC.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Remove 'label' property from SDHC nodes. We can use variants of
DEVICE_DT_GET to get access to a device pointer for use in an
application.
Signed-off-by: Kumar Gala <galak@kernel.org>
The 'nxp,imx-flexspi-device' compatible that was specified in
the YAML file is not an actual compatible that is intented to be
used. Instead the YAML file is included in other YAML files
that set specific compatible.
If the 'nxp,imx-flexspi-device' was used we'd actually get an error
from edtlib because of having the same compatible specified by
two different YAML files.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Clean up unused psl functions in scfg.c, unused DT macros, unused psl DT
nodes and related yaml files. Currently, PSL pad configurations are made
by pinctrl mechanism. Please refer
https://issuetracker.google.com/234861079 for more detail.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
HDA is a common IP used across the entire ADSP line and deserves
a name respecting that alongside similiar IP drivers such as the
ADSP GPDMA driver.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add adsp-imr binding. This memory type is being used in intel adsp dts
but this binding was missing.
Co-authored-by: Marcin Szkudlinski <marcin.szkudlinski@intel.com>
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
All in tree device drivers on a bus use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add simple clock control node in devicetree for beetle to handle
relationship between drivers (uart, timers, gpio) and clock controller
device.
Signed-off-by: Kumar Gala <galak@kernel.org>
Use DT_INST_FOREACH_STATUS_OKAY to reduce duplicated code for each
instance.
We make interrupts optional since they aren't always available.
Signed-off-by: Kumar Gala <galak@kernel.org>
Replace sensor_label property in devicetree with just a sensor phandle
property. This is more generic and allows driver to use DEVICE_DT_GET
instead of device_get_binding.
Signed-off-by: Kumar Gala <galak@kernel.org>
- adds properties 'group', 'index' and 'prescaler'.
- updates board's dts to include those properties.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Clean up unused pinmux function 'npcx_pinctrl_mux_configure()' and
related 'NPCX_DT_IO_ALT*' macro functions.
Please refer https://issuetracker.google.com/234861079 for more detail.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Switch from using a driver-specific, compile-time devicetree one-shot
property to supporting the newly added CAN_MODE_ONE_SHOT flag for
enabling/disabling one-shot mode at run-time.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove the support for enabling passthrough mode support for MPU9150
on the AK8975. We don't have a proper MPU9150 driver and the MPU9150
has been EOL. So its highly unlikely this code is being used.
Additonally we remove the device tree binding for the MPU9150 since
we don't have a proper driver for it.
Signed-off-by: Kumar Gala <galak@kernel.org>
CONFIG_SIFIVE_SPI_0_ROM (default y) was an option to disable spi0 if
used to access SPI Flash ROM. However, its design had a problem: it
relied on instance numbers. You had to set status okay for spi0 to make
it work (incongruent with the purpose of the option itself). This patch
makes things simpler: if such SPI0 is not available, simply keep it
disabled in DT. Bindings have been updated to mention this case.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
cAVS and ACE gpdma driver have several similarities. This commit merge
this two drivers into a single one for Intel ADSP devices.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add NPCX Power Switch Logic (PSL) DT node which controls the power rails
of SoC to get better power consumption.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL introduces how to configure PSL (Power Switch Logic) pads
properties such as input detection mode/polarity, pin-muxing and so
on via pinctrl mechanism. It includes:
1. Add two pinctrl properties and their enums for PSL input
detection configuration.
psl-in-mode:
- "level"
- "mode"
psl-in-pole:
- "low-falling"
- "high-rising"
2. Add macro functions to get PSL input detection and pin-muxing
configurations from 'pinmux', 'psl-offset' abd 'psl-polarity'
properties.
Here is an example to configure PSL_IN2 as the PSL detection input and
its mode and polarity.
/* A falling edge detection type for PSL_IN2 */
&psl_in2_gp00 {
psl-in-mode = "edge";
psl-in-pol = "low-falling";
};
A device will be introduced later which uses this pinctrl node to
configure PSL input detection settings and how to turn off VCC1 power
rail by PSL_OUT.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This peripheral combines a hardware-based USB CDC ACM serial interface
and a JTAG interface.
It is present in the ESP32-C3.
Signed-off-by: Martin Jäger <martin@libre.solar>
This will add ace compatible DMA driver.
Co-authored-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This adds basic support for the watchdog timer on the RP2040 MCU and
Raspberry Pi Pico development board
Signed-off-by: Jamie McCrae <spam@helper3000.net>
This commit adds support for the ds18b20 1-wire temperature sensor.
The sampling resolution of the sensor can be set in DT.
In case only a single device is on the bus, the driver issues
skip_rom commands. However, in case DT defines several devices,
the driver will use match_rom commands and therefore it is necessary
to set the rom_id of the device via the sensor attribute interface before
being able to sample sensor values.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The zephyr-serial w1 driver introduced in this commit implements
all routines for the w1 api on top of the zephyr serial driver.
W1 bit read, write, and reset operations are executed by issuing
polling zephyr serial byte read and write operations.
The driver should be usable on most platforms in zephyr that have
implemented support for the polling procedures of the serial driver.
As not all serial drivers are implemented exactly the same minor
additional quirks may be needed on some platforms.
The most notable difference of polling serial driver implementations
seems to be that some return immediately from poll_out after the
transmission was started(e.g. STM32) and others wait until
the transmission was completed before returning from poll_out
(e.g. NRF). While this has influence on the timeout, both types
are supported by this driver because the driver waits for a
configurable time period until it terminates the read.
The driver needs an appropriate open drain interface to be able
to communicate with slaves.
In the simpliest case this might be achived by configuring the mcu pins
in open-drain configuration with a (sufficiently small) pull-up to 3V3/5V.
Otherwise an external circuit needs to provide this interface.
Overdrive and Standard Speed modes are supported by this driver.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit introduces a new api for the Dallas 1-wire protocol.
The api includes link functions for read and write operations on
bit, byte, and block level, as well as functions to reset and
lock the bus.
The bus configuration is derived from the device tree and can be
queried using w1_slave_count routine.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The default S0S1 drive setting is not suitable for TWI/TWIM pins.
Override it with S0D1 as for some SoCs (e.g. nRF52833) without
this the peripheral will not work properly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
There is no driver or other references to the zephyr,ipm-console
devicetree compatiable. So remove the binding.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add binding for zephyr sdmmc disk device, which uses the SD
subsystem to manage an SD memory card.
Fixes#46410Fixes#46266
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add a stm32h7 spi compatible.
This compatible intends to match all SPI hardware blocks that
can be compatible with the one available in stm32h7 devices,
for instance, but not limited to stm32u5 and stm32mp1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use consistent name for SPI HW block property so applications
using a device tree overlay work transparently.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Add MKR header connector that is implemented by Arduino MKR series.
This allows hardware with compatible headers to define the related GPIOs.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Some EFR32 SoCs use a secure element subsystem to manage
security features (i.e., TRNG, secure bootloader or cryptographic
functions).
This driver relies on the SE Manager high-level API provided by Silicon
Labs. The API interacts with the SE subsystem, provides helper functions
to achieve cryptographic operations and ensures that only one operation
is running at a time by using mutexes and semaphores.
Instead of relying on the SE Manager from Silicon Labs, one could
recreate the behaviour of the Manager and put the code in the crypto
driver folder and create a dependency for other drivers using the crypto
manager (e.g., keys, entropy).
I went for the SE Manager API as it is already there and supported by
Silicon Labs.
Tested using the random subsystem.
Signed-off-by: Steven Lemaire <steven.lemaire@zii.aero>
Add the stm32g0 bindings for the HSISYS to be used with the hsi divisor
with a factor programmable from 1 to 128.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
According to the formulas found in the reference manuals of the SoC
families using the "st,stm32-temp-cal" version of the temperature sensor
(i.e. G0, G4, H7, L0, L1, L4, L5, U5, WB, WL), the temperature is
computed with the following formula:
T = ((TS_CAL2_TEMP - TS_CAL1_TEMP) / (TS_CAL2 - TS_CAL1))
* (TS_DATA - TS_CAL1) + TS_CAL1_TEMP
What is called ts-cal-offset in the stm32_temp driver is therefore the
same value as TS_CAL1_TEMP1. Use it directly instead of defining another
property.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The stm32_temp driver defines the ts-voltage-mv property to determine
the reference voltage of the ADC in the temperature computation. However
this information is already available in the device tree at the ADC
level (even with the same default value). Use it through the ADC API
instead of duplicating the information.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This new DTS Node is defining a ratio for Vbat internal
bridge of monitoring sensor connected
to a ADC internal channel. The voltage reference value
is given by the ADC of the stm32.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Like other temperature or vrefint sensor, the stm32 mcu
also have a Vbat monitoring internal channels on ADC.
Add this entry to the device tree.
The vref is usually 3300mV present on the target board.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
-pin properties, e.g. tx-pin have been replaced by pinctrl. Mark them as
deprecated since old pin configuration schemes will be deprecated in
Zephyr 3.2.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit moves the hardware configuration for ledc
peripheral to the device-tree instead of Kconfig.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Enable pin control support for SWO log backend, by creating a new
ITM node for the ARM instrumentation trace macrocell. Add pin control
properties under this node, and refactor the swo-req-freq property to be
defined within this node.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit rewrite renesas R-Car clock driver in order
to be able to support any new SoC easier.
This work is so creating a clock driver per soc alongside a
common driver for all reneasas r-car boars.
- drivers: create a driver per soc
- create a common driver
- create a common header used by soc & common driver
- create a soc specific driver calling for common driver
- dts: use new compatible
- use old yaml as common yaml
- create a new "child" yaml to define the new compatible field
- change compatible in device tree
As in Linux, the driver can support both r8a77951 and r8a77950
SoC's so we decided to name the new driver as in Linux with Zephyr
prefix : "clock_control_r8a7795_cpg_mssr.c".
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Panasonic's reduced Arduino header is based on the Arduino UNO layout.
The main difference is that some pins are not available due to the
lack of pins on the Panasonic module.
Signed-off-by: Steffen Jahnke <steffen.jahnke@eu.panasonic.com>
Bindings for Intel HDA now require the buffer alignment property to be
set.
Sets the property to 128 bytes for the common Intel cAVS device tree as
was implied by the tests cases.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Enable statically allocated buffers to determine their buffer alignment
with a device tree property rather than having to find out through docs.
Should save people lots of time.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add I2C bus recovery support to the NXP MCUX LPI2C driver. Since the LPI2C
peripheral block does not natively support I2C bus recovery, recovery is
performed using GPIO bitbanging.
Fixes: #42574
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The armv8 timer, arm gic, and arm gic-v3-its don't use or need the
devicetree label property. Update the dts bindings to not require it and
remove setting of the label property in dts files.
Signed-off-by: Kumar Gala <galak@kernel.org>
In 8f9290d2741844 ('dts: bindings: riscv: Add and use bindings for
sifive CPUs'), new compat strings for SiFive CPUs were added, but with
riscv prefixes. Vendor-specific compats should just be prefixed with the
vendor, so move that over here.
Fixes: 8f9290d2741844 ('dts: bindings: riscv: Add and use bindings
for sifive CPUs')
Signed-off-by: Olof Johansson <olof@lixom.net>
G4 and U5 series missed clock information in DT. Driver likely worked
because it was using HAL helpers, bypassing the purpose of DT and clock
control drivers. The clocks property is now required in the binding
file.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Adds `four-byte-opcodes` property. When set, then used write and read
opcodes will be converted to 4-Byte opcode.
Doesn't convert erase opcodes yet.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds write opcode (`writeoc`) property. That allows to provide
custom write opcode in the DTS.
Doesn't support OPI mode.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
The driver supported getting register shift from Devicetree, from a
custom definition in SoC headers (fragile) or, it took a default value.
This change simplifies things by making reg-shift property required in
all instances.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The reserved memory mechanism (sections and regions definition) has been
entirely replaced, greatly extended and made it better by the work done
on the zephyr,memory-region compatible.
Since there is are no actual users, we can remove it.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This reverts commit 7f51907fda.
The problem with setting the priority at the highest priority possible
is that when the IPC is under high traffic, the WQ could starve the
scheduler.
Move back to a more sane preemptive priority as default value.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This includes DTS bindings for the Texas Instruments CC13xx/CC26xx flash
controller driver and adds support for it in CC1352R and CC2652R SoCs
DTS files.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Recently OpenAMP introduced the possibility to set the sizes for TX and
RX buffers per created instance. Expose this also to Zephyr users by
using a DT property "zephyr,buffer-size".
For the sake of simplicity use the same DT property to set the buffer
size for both TX and RX buffers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Extends #43119 with PPB and IO values of
`memory-region-mpu`.
That allows MPU region definition with
PPB or IO attributes in the DTS.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
This patch adds DTS properties for using wake-up mode
and the autosleep function to the ADXL362 driver.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Add a pseudo device diver with device tree bindings for coredump.
The device tree bindings exposes memory address/size values to be
included in any dump. And the driver exposes an API to add/remove
dump memory regions at runtime.
Signed-off-by: Mark Holden <mholden@fb.com>
This commit aligns SPIM shim to utilize memory-region property from
nordic,nrf-uarte compatible. The memory-region is not required
property that enables user to specify placement of dma buffers
in memory region. It is done by assigning to memory-region property,
phandle to node with zephyr,memory-region and mimo-sram compatible.
When memory-region property is not specified for given
instance, buffer is placed in default RAM region with other data.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
This commit aligns UARTE shim to utilize memory-region property from
nordic,nrf-uarte compatible. The memory-region is not required
property that enables user to specify placement of dma buffers
in memory region. It is done by assigning to memory-region property,
phandle to node with zephyr,memory-region and mimo-sram compatible.
When memory-region property is not specified for given
instance, buffer is placed in default RAM region with other data.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Since the introduction of the `zephyr,memory-region` compatible
to create new memory region, drivers can now use the newly defined
region in the DT by using the macro LINKER_DT_NODE_REGION_NAME()
on the node_id to retrieve the region name and possibly allocated data
or variables in that region (or for whatever other use).
This is assuming though that the driver knows in advance the node_id to
reference.
A better approach is to add a new generic 'memory-region' property
that can be used by any driver to reference a region by using a phandle,
so that the driver can use that to retrieve the memory-region of interest.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The ALH is an intermediary device, which acts as a hub and provides an
abstracted support for numerous sound interfaces (e.g. SoundWire).
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
This sensor is virtually identical to the lsm6dso. The only difference
is the accelerometer ranges are double those of the lsm6dso.
Use the same driver. The difference is detected by using "st,lsm6dso32"
as the first compatible entry, followed by "st,lsm6dso".
An bit flag in the existing accel_range config field is used to check if
the chip is the doubled range or not.
Signed-off-by: Trent Piepho <trent.piepho@igorinstitute.com>
Config pwm open-drain mode without enabling STORE_REG. This CL
collects all active PWM's base address and related index in an
array. Then, pinctrl driver configs its open-drain mode by
finding the corresponding 'channel' index.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Pinmux is depricated (see #39740) and shouldn't be used anymore
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Extend the common ADC controller binding with a child binding that
allows specifying configuration of ADC channels.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add 'inversion-on' property to st7735r.
Issue INVON(21h) command on initializing if inversion-on was enabled.
As a result of this command, the display color is inverted.
Otherwise, INVOFF(20h) will be issued.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add pin control support for IOMUXC peripheral present
on mimx8ml8_m7 soc. This reuses the existing pin
control driver for the IOMUXC peripheral, but uses a
new header and compatible binding to handle the
different register layout on this SOC.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add pin control support for IOMUXC peripheral present
on mimx8mq6_m4 soc. This reuses the existing pin
control driver for the IOMUXC peripheral, but uses a
new header and compatible binding to handle the
different register layout on this SOC.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add pin control support for mcimx7_m4 SOC. This reuses the existing pin
control driver for the IOMUXC peripheral, but uses a new header and
compatible binding to handle the different register layout on this SOC.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add the DTS binding for OCTOSPI interface for the stm32 devices
from STMicroelectronics.
This corresponds to a NOR octo SPI flash.
In this config, there is only on NOR-flash device.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx eSPI and host_subs driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx adc driver. Please notice users need to
configure the corresponding pinctrl nodes in 'pinctrl-0' property in the
adc0 DT node. For example, if ADC0 and ADC2 channels are selected for
the application, please add the follwoings in your board DT layout file.
&adc0 {
status = "okay";
/* Use adc0 channel 0 and 2 for 'adc_api' driver tests */
pinctrl-0 = <&adc0_chan0_gp45
&adc0_chan2_gp43>;
pinctrl-names = "default";
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx tachometer driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in ps2 driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in pwm driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in i2c driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in uart driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL is the initial version for npcx pinctrl driver and introduces
pinctrl nodes for both IO-pads and peripheral devices for each npcx
series. Users can set pin configuration via these nodes in the board
layout DT file. It also wraps all configurations related to pin-muxing
in pinctrl_soc.h. Regarding the other pin properties, we will implement
them later.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The drive-mode property is nRF specific, so prefix it with `nordic,`,
same as the `nordic,invert` property.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Enable pin control for lpc11u6x i2c driver, and remove pinmux usage from
board level DTS files.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
convert lpc11u6x syscon clock driver to pin control, and remove all
pinmux usage from driver and syscon dts node.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update pin control driver for lpc11u6x. This SOC does not have a HAL,
so fsl_clock is not available. It also lacks a slew-rate field in the
IOCON register, so this property must be optional.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
switch gpio driver to use pio nodes to configure pin control settings,
and stop using pinmux driver within gpio driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Since implementation of clock source selection in consumer device drivers
could be achieved without usage of a clock-names property and no
example of usage is provided up to now, remove this property from existing
examples.
Additionally, make it clear in stm32 clock control binding that it is
driver's responsibility to correctly access clock source information
and use it as required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add STM32 clock mux binding.
Only property of a node using such compatible is to
select a clock input.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the UPLLCK clock for the CAN controller as recommended by the Atmel SAM
E70 data sheet.
Move the configuration of the clock prescaler from Kconfig to devicetree
and limit it to the values recommended by the SAM E70 datasheet.
Fixes: #45012
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add DTS binding for Motorola MC146818 compatible Real Time Clock.
This is being used for the RTC/CMOS timer on x86 PC-compatible
platforms.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add optional PINCTRL support to the Microchip XEC PS2 driver
shared between MEC15xx and MEC172x families.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Comparator will monitor signal though ADC channel, based on
user configuration, callback will be triggered.
This will enable comparator functionality for nuvoton MCU utilizing its
ADC threshold detection feature. Implementation is exported through
sensor trigger API. Use of CONFIG_ADC_CMP_NPCX is required.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
remove existing SDMMC SPI driver, since it is replaced by the SPI mode
SD host controller driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
with the legacy USDHC driver fully removed from the tree, the
nxp,imx-usdhc binding can now be used for the new SD host controller
driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
all in tree SOCs with the USDHC peripheral have now been converted to
use the new SD host controller USDHC driver, so remove legacy NXP disk
USDHC driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add SDHC driver implementing spi mode support for SD cards. This driver
implements the standard SD host controller APIs, and sets the host
property "is_spi" to indicate to the SD subsystem the card will be
running in SPI mode.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add generic SDHC dts binding, as well as DTS binding for NXP USDHC.
Update iMX.RT DTS binding to use USDHC compatible
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Make the LSE driving capability configurable for the STM32 series.
Fixes#44737.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Fix the descriptions for the ST STM32 FDCAN devicetree bindings. These
are derivates of the Bosch M_CAN, but they target specific SoC
implementations.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the base Bosch M_CAN CAN-FD controller devicetree binding to
match the product name and the upstream Linux devicetree binding.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Fold the simple bosch,m-can devicetree binding into the front-end
devicetree bindings. The bosch,m-can compatible is not used in Zephyr.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
MCP4728 is a 12-bit, Quad Digital-to-Analog Converter with EEPROM Memory.
Controlled via I2C interface.
Signed-off-by: Marek Janus <marek.janus@grinn-global.com>
In 92d8329d5b a new DT property was introduced to set the WQ priority
of the instance. The fallback value when the property was not present
was arbitrarily set to <0 PRIO_PREEMPT>.
The problem is that this value is actually changing the behaviour for
the code that is not explicitly setting the DT property, breaking in
some cases the existing code.
Move the default value to <0 PRIO_COOP> to give the old code a
consistent behaviour before and after the 92d8329d5b commit.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This is a follow-up to commit 1a01ca2adf.
Since support for pinctrl has been added to the qdec_nrfx driver,
the related binding can no longer require the `a-pin` and `b-pin`
properties to be defined.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add DT option to configure the data ready interrupt mode.
Latched is the default; pulsed can be enabled through
the drdy-pulsed DT, if desired.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
Add FDS (Filtered Data Type Selection) + High-Pass reference mode support
(FDS in CTRL6, HP_REF_MODE in CTRL7)
Values are configurable through DT per instance.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
The PWM period cell will soon be required by the pwm_dt_spec facilities,
this patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The binding has no corresponding driver and it is not referenced
anywhere, so drop it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The binding did not define the PWM cells. Only channel and period have
been added as they are the minimum required ones (flags are not supported).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PWM period cell will soon be required by the pwm_dt_spec facilities.
This patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PWM period cell will soon be required by the pwm_dt_spec facilities.
This patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The period cell will soon be required by the pwm_dt_spec facilities,
this patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PWM period cell will soon be required by the pwm_dt_spec facilities,
this patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The period cell will soon be required by the pwm_dt_spec facilities,
this patch adds it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The period cell will soon be required by the pwm_dt_spec facilities,
this patch adds it. Note that flags have not been added as they are
optional and not supported anyway.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Introduce has-interrupt-mask-reg DTS property for nxp,pca95xx driver.
This additionnal property allow to specify that the gpio expander has an
interrupt mask register that must be configured by the driver.
This allow to use this driver with PCAL95xx.
This fixes issue #44834.
Signed-off-by: Xavier Chapron <xavier.chapron@stimio.fr>
NXP LPUART IP supports loopback mode, where TX is internally connected
to RX input. Allow setting loopback mode up via the "nxp,loopback" dts
property.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Align the board dts with the recent changes in the "nordic,nrf-sw-pwm"
binding (remove the no longer existing `channel-count` property) and
add a node representing the edge connector for convenient referring
to SoC pins connected to it.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
... to align with what is used in most other PWM bindings.
Update PWM nodes in SoC .dtsi files accordingly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Align with other PWM drivers and treat the `pwm` parameter (described
ambiguously as "PWM pin") of the `pwm_pin_set_cycles` function as a PWM
channel, not an SoC pin. This will also make the driver consistent with
the `pwm-cells` property definition in the "nordic,nrf-sw-pwm" binding
and with related `DT_PWMS_*` macros.
The change described above requires also providing a way to specify
SoC pins that are to be assigned to the PWM channels. Hence, the commit
introduces in the "nordic,nrf-sw-pwm" binding the `channel-gpios`
property that replaces the `channel-count` one.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Rework bindings documentation to clearly illustrate the role of ahb
(and cpu1) prescaler which defines the actual core clock frequency,
and not only a bus frequency.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use enum to describe the range of allowed MSI values.
This will help to detect configuration issues earlier.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On some parts, it could be required to use steps before applying
highest frequencies.
This was previously done as part of LL_PLL_ConfigSystemClock_FOO
utility functions which are no more used.
Use device tree to mention when this is required and implement it
in stm32_clock_control_init().
Additionally, fix the calls tp LL_RCC_SetAHBPrescaler, which require
use of ahb_prescaler helper.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The pinctrl support made usage of the 'peripheral'
property no longer required.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
those bindings are no more needed since pinmux was
deprecated in favor of pinctrl.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
After pinctrl's subsystem support, I2C pin properties are
no longer required for pin muxing, however, this information
is still valuable in an eventual FSM failure if the target
SoC has no harwared mechanisms to support bus recovery.
In this case, bus recovery uses pin information to restore
the I2C bus state.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Adds hda link in and out drivers. The link in and link
out channels of HDA have small differences
with the host channels. Updates the existing
cavs_hda drivers and code to account for these
differences.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
all the consumers of the obsolete pinmux driver is
updated to use pinctrl API, this commit removes
the pinmux driver and assosciated sections.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
This commit has the necessary changes to update the consumers
of pinmux driver(SPI, I2C, UART) and update the board specific
files to use the pinctrl interface.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
Add pinctrl driver for CC13XX/CC26XX family of SoCs
to facilitate transition from pinmux to pinctrl.
`IOCPortConfigureSet()` from TI hal driverlib used to
implement the generic pinctrl driver.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
LPTIMER has a different `countermode` meaning.
We shall exclude introduced property from lptim bindings.
Alternative property (e.g. `external-mode`) can be added
later on to support external counter mode.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Introduces H7 FMC bindings with support for
memory remap or swap configuration.
The following values are supported:
* disabled - default mapping (reset state).
* sdram-sram - swaps the NOR/PSRAM and SDRAM banks.
* sdramb2 - remaps SDRAM bank 2.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
the icm42670 from Invensense/TDK is a 6-axis accelerometer with
gyroscope and temperature sensing capabilities.
this initial driver does not support the devices 2K FIFO or many of the
other advanced features. Instead, only basic features are implemented.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
Add the period cell to GD32 PWM compatible and update all boards
accordingly. A period of 20 ms (50 Hz) has been set for all PWM LEDs.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Rather than specify input clock for each peripheral individually, instead
specify the relevant clocks in DTS.
This will enable easier support for non-default coreclk on fe310 in a
follow-up CL.
Signed-off-by: Shawn Nematbakhsh <shawn@rivosinc.com>
Currently the only way for a BOARD/SOC to configure at compile time the
MPU regions is to add, in a soc-specific file, the 'mpu_config' struct
adding static entries for the new regions with the needed attributes
(cacheable, non-cacheable, etc...). This exported struct is then read by
the MPU driver at boot time and used to properly setup the MPU regions.
At the same time it is now possible to introduce new memory regions in
the DT using the newly introduced 'zephyr,memory-region' attribute.
What is missing is the link between these two solutions: that is how to
declare the memory regions in the DT and automatically configure these
regions in the MPU with the correct attributes.
This patch is trying to address exactly this problem.
It is now possible to declare the memory regions in the DT and define
the MPU attributes for the regions using the 'zephyr,memory-region-mpu'
property. When this new property is present together with the
'zephyr,memory-region' property and a the 'zephyr,memory-region'
compatible, the 'mpu_config' struct is automatically extended at
compile-time to host the DT defined regions with the correct MPU
attributes.
So for example in the DT we can now have:
sram_cache: memory@20200000 {
compatible = "zephyr,memory-region", "mmio-sram";
reg = <0x20200000 0x100000>;
zephyr,memory-region = "SRAM_CACHE";
zephyr,memory-region-mpu = "RAM";
};
and a new region will be created called "SRAM_CACHE" and a new MPU
region will be configure at boot time with the attribute
"REGION_RAM_ATTR".
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add a new boolean devicetree property `tx-rx-swap` to the
st,stm32-usart binding, used to control TX/RX swap during
device initialization.
Signed-off-by: Alexander Mihajlovic <a@abxy.se>
Add boolean properties to the binding for the nRF RADIO peripheral
to indicate whether the following features are supported:
- IEEE 802.15.4 mode
- 2 Mbps BLE mode
- coded BLE PHY
- high TX power settings
Set these properties appropriately in devicetree radio nodes for all
nRF SoCs.
Add also such properties and set them in appropriate nodes for nRF
flash controllers to indicate whether they support partial erase.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
For consistency with the scheme used for other nRF peripherals,
use the peripheral name that nRF Product Specifications use.
In this case, it is WDT, not WATCHDOG.
Also remove the requirement for the label property in the binding.
It is no longer needed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add missing devicetree nodes representing the following peripherals
in nRF SoCs:
- ACL
- BPROT
- CCM
- COMP/LPCOMP
- CTRLAP
- DCNF
- MPU (nRF MPU peripheral in nRF51 Series, not ARM MPU)
- MUTEX
- MWU
- NFCT
- OSCILLATORS
- POWER (in nRF51 and nRF52 Series)
- PPI
- RESET
- SWI
- USBREG
Add also corresponding bindings and validation of base addresses of
these nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Adds an initial driver for HDA streams on cAVS. A common code base is
provided for all HDA streams while the drivers are identified
differently as they have small behavior differences.
Uses dma_status to describe the positions for read/write. Uses dma_reload
to inform when to move the read/write positions. This closely follows
how HDA is being used in SoF
Simple test case is provided for both drivers.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add build time optional PINCTRL support to the Microchip XEC TACH
driver shared by MEC15xx and MEC172x families.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Update Microchip XEC TACH driver to support MEC172x.
Standardize device tree properties between chips.
Standardize device structure usage.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Depending on the stm32 mcus and the timer instance, several channels
can enable the complementary output for the PWM signal.
Example of a DTS <&pwm1 2 4 (PWM_POLARITY_NORMAL | PWM_COMPLEMENTARY)>;
Note that the timer channel must support the complementary output
on that channel : usually channels 1-3 + channel 4 on stm32g4x.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Follow up on commit 37bf7cb
("dts/bindings: stm32: Set pinctrl-[0/names] properties as required")
Report lack of those fields soon at build to avoid cryptic
DT api build error messages.
Signed-off-by: Maciej Zagrabski <maciej.zagrabski@grinn-global.com>
Instead of having one single WQ per backend, move to one WQ per
instance instead and add a new "zephyr,priority" property in the DT to
set the WQ priority of the instance. Fix the sample as well.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add Nano header connector defined by Arduino. This allows
hardware with compatible headers to define the related GPIOs.
Signed-off-by: Marco Peter <marco.peter@joylab.ch>
Add description for a plain GPIO configuration using
st,stm32-pinctrl and st,stm32f1-pinctrl bindings.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add backlight gpios property to mcux display driver, so that the driver
can correctly initialize the backlight gpio control.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
In order for pinctrl support to be complete, RT series GPIO driver must
support pinmuxing within the driver level. RT series pinmux settings do
not correspond directly to gpio port/pin numbers, so use DTS mappings to
pinctrl nodes to select and apply pinmux settings in the gpio driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enable pinctrl driver for usdhc. USDHC driver uses custom pinctrl states
for fast, slow, and medium signal frequencies, as well as pin pull for
SD detection.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enable pinctrl for flexspi driver. Note that when flexspi is being using
in XIP mode, pinctrl settings are not required and will not be applied.
Pinctrl settings are only required when the flexspi device being used is
not the one used for XIP.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
RT11xx series has similar pin configuration peripheral to RT10xx, with
some differences in register layout. Create new pinctrl definition
header file, and reuse existing driver code for RT10xx.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
iMX.RT parts use a GPR register for some pinmux settings. Update pinctrl
driver to support this GPR register definition.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This update Atmel sam and sam0 ethernet gmac and mdio drivers to use
pinctrl driver and API. It updates all boards with new pinctrl groups
format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 rtc driver. It allows to
define pins to be used for tamper detection.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 dac driver. It updates all
boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 usb dc driver. It updates
all boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 tcc pwm driver. It updates
all boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 i2c driver. It updates all
boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This add support to pinctrl at Atmel sam0 spi driver. It updates all
boards with new pinctrl groups format and drop pinmux entries.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam0 serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update current Atmel sam0 pinctrl initiative to current Zephyr
pinctrl API. It update current devicetree bindings and add the sam0
pinctrl driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam qdec sensor driver to use pinctrl driver and API.
It update board and sample with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam pwm driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format. In addition this
remove all remaining manual pinmux at board level.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam canfd driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format. In addition this
add missing entries to run automated tests for can/canfd drivers.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam ssc driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format. In addition this
remove DEV_NAME macro at sam xdma driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam afec driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format. In addition, it
add overlay files to allow run samples/drivers/adc example.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam usb drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam counter driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam i2c drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format. This add missing
i2c-0 alias into sam4l_ek board.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam spi driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update current Atmel sam pinctrl initiative to current Zephyr
pinctrl API. It update current devicetree bindings and add the sam
pinctrl driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit makes the transition from the pinmux driver to the pinctrl
driver. It also modifies UART, SPI and I2C drivers used in FE310-based
boards to use the new pinctrl API.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The PLL div-p for the stm32g4x has more possible value than stm32l4
possible ra nge is from 2 to 31
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Adds an entropy driver that uses Bluetooth HCI commands as its source
of randomness. As this method is blocking, the ISR API is not supported.
As this method will range from relatively slow (same core Bluetooth HCI
controller) to extremely slow (UART HCI Bluetooth controller), use the
xoshiro PRNG by default for RNG generation.
Implements #37186
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
added bindings for vnd,reset used for devicetree test reset
added adc temp sensor as supporting reset
Signed-off-by: Andrei-Edward Popa <andrei.popa105@yahoo.com>
added bindings and compatible for reset controller nodes
added bindings for devices that use the reset controller
Signed-off-by: Andrei-Edward Popa <andrei.popa105@yahoo.com>
the tlc5971 driver uses spi for controlling the global brightness
and individiual pixel brightness of a daisy chain of tlc5971
devices.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
If a user has a 1GB external flash it is currently not possible
to configure this through DTS. To allow for such a configuration
we add an option which specifies the size in bytes not bits.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
This commit adds ipc backend, that relies on simple
inter core messaging buffer also added by this commit.
This backend is configurable with DT overlay. Each
ipc instance could be defined with ipc-icmsg commpatible.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Enable pinctrl for ethernet mcux driver, and update kinetis DTS node to
include labelling for PTP node, to enable driver to access pinctrl
properties.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
kinetis pinctrl driver had swapped values for slew rate
(fast slew rate should set bit to zero). Fix slew rate values.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
- Move the SX oscillator control pins to a regulator node
- Create a board level compatible for the RF switch
- Use gpio_dt_spec to simplify board pins.c (now rf.c)
- Cleanup include list
For reference:
https://downloads.rakwireless.com/
LoRa/RAK811/Hardware_Specification/RAK811_HF_Schematics.pdf
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add build time optional PINCTRL support to common PWM driver
for Microchip XEC MEC15xx and MEC172x families.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add support for MEC172x series to Microchip XEC PWM driver.
Standardize device tree properties for both SoC families.
Standardize device structure usage.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add the Vref reference voltage in the DTS, so that the adc driver
can retrieve the value for conversion.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
As mentioned in #42882, the I2C of IT8XXX2 is designed for two different
IP blocks, so this PR divides this I2C driver into two compatibles.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Adds 'swj-cfg' property to the F1 pinctrl. It is an optional
property that allows to control Serial Wire JTAG
configuration.
Different configurations allow to free certain IO
pins that can be used in remap or standalone.
That replaces previously used Kconfig approach.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
This contains accessor macros for getting the maximum bitrate supported
by a CAN controller/transceiver combination.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add generic devicetree bindings for simple CAN transceivers.
Always-on CAN transceivers are considered passive and just provide a
maximum supported bitrate.
Active CAN controllers can typically be controlled by the MCU via either
SPI, I2C, or GPIO. Common GPIO controlled CAN transceivers provide
either a stand-by or an enable pin (or both) for controlling the state
of the CAN transceiver.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for the new pinctrl API to the nRF PWM driver.
Update code of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the nRF QDEC driver.
Update code of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the nRF QSPI NOR flash driver.
Update code of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for configuring pins to be used by the nRF PWM, QDEC, and
QSPI peripherals.
A new custom property "nordic,invert" is added to the pin configuration
group binding to allow configuring PWM channel outputs as inverted.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the DMIC driver that handles
the nRF PDM peripheral. Update code of the driver and the related
devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the nRF I2S driver. Update code
of the driver and the related devicetree binding.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Bindings for the Xilinx Processor System GPIO controller, both for the
parent controller device as well as the GPIO pin bank child devices.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
Add dts binding for rt1xxx pinctrl driver settings. A binding file is
present for the pinctrl node itself, and for the pinctrl child node that
defines all pinmux options
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce ADC properties which indicated if the ADC instances have
dedicated channels for the internal temperature sensor or voltage
reference.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This macro expands to DT_STRING_TOKEN if property exists, otherwise
falls back to default value.
Helpful when a non-required enum binding doesn't mention a default
value, but a default value makes sense to be set in the code.
Including DT_INST_STRING_TOKEN_OR and test code.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
Add support for the new pinctrl API to the I2C drivers that handle
the nRF TWI and TWIM peripherals. Update code of the drivers and
related devicetree bindings.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for the new pinctrl API to the SPI drivers that handle
the nRF SPI, SPIM, and SPIS peripherals. Update code of the drivers
and related devicetree bindings.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
1. Check I2C Clock and Data is high through GPIO driver instead
of the I2C bitbang registers
2. i2c_xec_poll_write() and i2c_xec_poll_read() will poll to
check I2C clock and data lines are high before initiating the
transaction. The polling will be every 25us for a cumulative
max of 2.5ms
3. wait_completion() will not call recover_from_error() to reset
the controller. Instead will poll for 10ms for the PIN bit to
clear before returning error.
4. wait_completion() will send STOP if the 9th bit is NACK
5. If any errors with current transaction:
(a) Set error_seen flag.
(b) In the next transaction do the recovery process (reset the
i2c controller) if the clk and data lines are high.
Note: error_seen flag is set for Address NACK with Repeated
Start as well.
6. If timeout error occurs in wait_completion():
(a) Set timeout_seen flag;
(b) Wait till the slave will release the clock.
(c) Once slave releases clock send STOP on the bus. If the
timeout occurred while master read, read the I2C DATA register
for the hardware to proceed.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Allow movement detection to be used on hardware
that only has one interrupt line connected.
Change hardware configuration to a bitmask.
Signed-off-by: Andrew Hedin <andrew.hedin@lairdconnect.com>
Add a new hwinfo driver to get the reset cause on
SAM4S/SAME70/SAMV71 SoC series.
The user-nrst dts property has been added to enable external user
resets.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
This commit implements the temperature sensor interface for
the Maxim MAX31875Low-Power I2C Temperature Sensor.
Signed-off-by: Pete Dietl <petedietl@gmail.com>
In nRF53 family of SoCs, GPIO pins must be explicitly forwarded by the
application core to the network core if the latter should drive them.
Add a binding of a generic GPIO pin forwarder.
Signed-off-by: Jedrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
The driver was never migrated to Devicetree, this patch converts the
driver to a proper Devicetree based device.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This adds support for the ads101x (ads1013, ads1014, ads1015) and
ads111x (ads1113, ads1114, ads1115) family of i2c adc devices.
Signed-off-by: Ryan McClelland <ryanmcclelland@fb.com>
Introduce a new "zephyr,memory-region" compatible to be used when a new
memory region must be created in the linker script from the devicetree
nodes using the compatible.
Remove also the LINKER_DT_REGION_FROM_NODE macro and add a new
LINKER_DT_REGIONS macro to cycle through all the compatible regions.
In the same PR modify the DTS files and the linker scripts.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Intel's adsp needs to set, at a minimum, a clocking bit before the driver
can initialize the designware dma controller. In many ways it is the
designware dmac IP but with additional registers and functionality added
on top of it. So the code structure here follows how the hardware
appears to be designed, layered on top of the designware driver.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
This is the compatible which is used in the blinky sample, so
it's worth trying to add a better example for what you can do with it
in general in the main description.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Exposes the RC register so that the initial value can be set in
the device tree. This is useful in the case where the timer
generates an event but an interrupt is not required.
e.g generate event to sample adc on RC register match.
Tested on Atmel SMART SAM E70 Xplained Ultra board
Signed-off-by: Marius Scholtz <mariuss@ricelectronics.com>
Current uart driver implementation is incompleted regarding the
usage of DT_INST_FOREACH_STATUS_OKAY. If uart0 and uart2 are selected,
build breaks due to peripheral number ordering, which would be
0 and 1 in this case. This fix PR fix this by re-working the macros
and setting proper uart peripheral instances in DTSI, required for signal
routing configuration.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Build shows warning due to incompatible
CPU vendor name. This fixes it and applies
necessary changes in files.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Initial implementation of a simple GPIO controlled power domain.
It exposes no API of its own, all functionality is contained inside
the runtime power management callbacks.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add support for power domains on Zephyr. Power domains are implemented
as simple devices so they can use the existent Zephyr API, for resume
and suspend sync and async and also reference count.
The pm subsystem will ensure that domains are resumed before and
suspended after devices using them. For device runtime power
management, every time the device is got or released the same actions
is done to the domain it belongs.
As domains are implemented as simple devices, it is totally acceptable
a domain belongs to another domain.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add support for disabling automatic retransmission of CAN frames
(similar to CAN "one-shot" mode in the Linux kernel).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Renesas R-Car series contains a PFC (Pin Function Controller).
This module consists of registers for selecting the function of
the multiplexed pins and controls the pull-up resistor on each pin.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Remove the unused base binding for CAN bus devices (as in devices
present on a CAN bus). This binding should have been removed in
2269408572
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
On some platforms, HPET is not wired to trigger IRQ 2.
This would make HPET non-functional if the legacy
interrupt routing bit is set in the global config
register. This adds a DTS flag so the driver won't
set the bit to enable legacy interrupt.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
dts/bindings/timer/riscv,machine-timer must have compatible name
riscv,machine-timer. nuclei,machine-timer is wrong, correct it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
This PR adds the different handling of temperature sensor for the
STM32L5 soc. In this soc, there are some calibration settings which
need to be applied for temperature conversion.
Signed-off-by: Wouter Cappelle <wouter.cappelle@crodeon.com>
The dts binding general rules document states that the property
description should explain why the default value was selected
(e.g. "default is the value at power-on").
See comment in #41143
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add fragment:
io-channel-cells:
- input
to binding of the "ite,it8xxx2-adc" and "zephyr,adc-emul" compatible.
It is necessary to use io-channels property.
Signed-off-by: Dawid Niedzwiecki <dn@semihalf.com>
An additional devicetree poperty `single-wire` is added
to uart and usart bindings of stm32. The driver checks this value
during initialization and enables the single wire mode when set.
Signed-off-by: Jonathan Hahn <Jonathan.Hahn@t-online.de>
The leon3 SoCs were missing definitions of the CPU node. This node is
now required for PM, so that power states can be defined.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Better setting a default value there so DT_PROP() will return something
relevant whether the property is set or not.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
NPCX7/9 has a different ADC register structure. NPCX7 has 3 threshold
detectors from offset 0x14 & has 10 input channels. NPCX9 has 6
threshold detectors from offset 0x60 & has 12 input channels.
This commit fixes the NPCX ADC register structure.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
YAML description file for the On-Chip Memory of the Xilinx
Zynq-7000, DT identifier "xlnx,zynq-ocm".
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
The spi-bus-width property provides information if the target system
has all SIO[0123] pins connected to NOR flash memory.
It must be equal to 4 to enable QSPI 4 IO operation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Some flash memories connected to QUADSPI IP block on stm32[fh]7 devices
require proper reset pulse before configuration.
This patch adds two new properties - the 'reset-gpios' phandle,
which allows specifying GPIO pin for RESETn pulse and
'reset-gpios-duration', which provides the time (in ms) for reset
duration.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'flash-id' property defines the number of QSPI's dedicated GPIO
bank (and flash ID), which will be used to communicate with flash
memory.
For example, on stm32h7xx it is possible to use 'quadspi_bk1_*' and
'quadspi_bk2_*' set of pins, so one may need to select between them
when required.
By default - pins from 'quadspi_bk1_*' bank are used, so the
'flash-id = <2>;' property, when your use case (e.g. PCB design)
requires it, forces usage of 'quadspi_bk2_*' pins.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Convert the CAN loopback driver from being configured via Kconfig to
multi-instance configured via devicetree.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The vnd,gpio-device compatible is now used by the test GPIO driver
(CONFIG_GPIO_TEST) introduced in #41387. This means that we can't define
new devices with this compatible when CONFIG_GPIO=y.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The pinsN group name can be a confusing in some circumstances, so change
it to groupN. Some platforms (e.g. nrf or gd32) are already using
groupN. Documentation and API tests have been updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
If there are no console messages input at an interval of 15
seconds, the system will be able to enter suspend mode.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
So far driver was using SENSE mechanism for all or none edge
interrupts. This was not convenient since in some modules may
require IN event to be used and other did not. Converting it to
use a mask specified in the device tree. Pins indicated in the
mask will use sensing.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add a new DT property named "pixel-group-size" that allows users to
configure the driver to refresh the matrix by illuminating multiple
LEDs in particular rows simultaneously. This way the maximum possible
brightness of the LEDs can be increased (as they can be lit longer)
and the timer interrupt handler is executed less frequently, what
results in decreased CPU load, but more GPIOTE/PPI channels needs to
be allocated if the PWM peripheral cannot be used. Thus, it is left
to users to select the configuration that suits them best.
Update definitions of both the bbc_microbit boards with this new
property, using the maximum available group size (to achieve maximum
possible brightness). For v2, no new resources are used (only all
channels in the already used PWM peripheral are now utilized).
For v1, two more GPIOTE and PPI channels are allocated.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Some STM32 series need to configure health test register
for proper RNG behavior.
In addition, some also require to write a Magic number
before writing the configuration.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
- Supporting multiple instances of ivShMem virtual devices.
- Introduces DT based configuration for ivShMem devices.
- Add DTS overlay file to test new multiple ivshmem instance capability.
- Enable BDF unspecified device initialization.
(limited to one instance. An improved version of pcie_bdf_lookup()
will come soon that fixes this limitation)
- Make PCIE DTS file macros available for a proper ivshmem device
properties parsing.
Sample for dts file:
pcie0 {
label = "PCIE_0";
#address-cells = <1>;
#size-cells = <1>;
compatible = "intel,pcie";
ranges;
ivshmem0: ivshmem@800 {
compatible = "qemu,ivshmem";
reg = <PCIE_BDF_NONE PCIE_ID(0x1af4,0x1110)>;
label = "IVSHMEM";
status = "okay";
};
};
Signed-off-by: Michael Schmidt <michael1.schmidt@intel.com>
GD32V SoC uses divided clock from core-clock for machine timer clock.
Add config of clock divide factor to support GD32V.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Implemented driver for the simcom sim7080 modem.
This driver features Socket offloading, TCP, UDP, DNS,
SMS, GPS and FTP.
Signed-off-by: Lukas Gehreke <lk.gehreke@gmail.com>
Remove the requirement for specifying #address-cells and #size-cells
properties for CAN controller devicetree nodes.
CAN controllers do not have a common concept of devicetree child nodes
and thus have no need for these properties. This is in line with
upstream Linux kernel devicetree bindings.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move odr and range properties for both accelerometer and gyro
from Kconfigs to Device Tree.
Fixes#41117
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Fix the yaml dts multi-line property description in the following
(expected) way:
description: |
PUT_TEXT_HERE
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Adding support for the TI TMP108 temperature sensor. This includes
over/under temp interrupt support as well as one shot, continuous
conversion and power down modes.
Signed-off-by: Jimmy Johnson <catch22@fastmail.net>
Add a display driver and the corresponding devicetree binding for a LED
matrix with rows and columns driven by nRF SoCs GPIOs. Such matrix can
be found, for example, in the BBC micro:bit boards.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Create an explicit ina230 driver which is supposed to
work with 230 and 231 variants. While at it switch
to i2c_dt_spec helpers and change device-tree node
names to use - instead of _ in order to follow
convention.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Create a common properties file that will be included by all bindings
(as i2c and spi) handled by lps22hh driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add support for the 8 channels TCA9548A I2C mux.
Added a new binding ti,tca9548a binding inheriting
properties from ti,tca954x-base and defining its own compatibles fields.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Add an optional "reset-gpios" phandle-array
field to the driver common yaml.
The reset GPIO channel and pin can be defined
in device tree as a node property.
The driver then deassert the reset signal at mux
initialization if a "reset-gpios" has been specified.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Prepare the driver to upcoming support of more mux references.
Rename all TCA9546A related files to TCA954x.
Keep ti,tca9546a and ti,tca9546a-channel compatible
for backward compatibility reasons.
New tca954x-base binding embedding common properties,
tca9546a binding inherits from it and define its own compatibles fields.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Include the mem-region bindings for the stm32 ccm nodes and set the name
in the current dtsi files.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add the compatible property to the board level sdram nodes in few stm32
dts files so that the zephyr,memory-region name is used correctly in the
linker script.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add bindings for SDL based display controller.
Rework SDL based display controller driver to obtain
configuration from devicetree. Remove unnecessary casts,
add multi-instance support.
Add display controller node and chosen property
to native_posix devicetree.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Include common display controller bindings.
Add required height and width properties to "ilitek,ili9340"
and "ilitek,ili9488" users.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Introduce optional `zephyr,linker-region` property which signifies that
the node should result in a linker memory region and what the name of
that region should be. Property added to compatibles likely to result
in a linker memory region; 'mmio-sram', 'arm,itcm`, `arm,dtcm`,
`nxp,imx-itcm`, `nxp,imx-dtcm` and `fixed-partitions`.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Refactor the mcp230xx driver to generically also support
SPI IO expanders, renaming it to mcp23xxx in the process.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
Add driver for MEC172x QMSPI with local DMA(LDMA). The driver
support SPI asynchronous operation.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
This commit adds a generic i2c regulator driver, and enables the NXP
PCA9420 PMIC IC using this driver. The regulator driver also exposes an
additional API in include/drivers/regulator/consumer.h, which allows
drivers to implement support for adjusting voltage levels and current
limits, if their device supports it.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
There is currently no information available about the XIP
addresses for the nRF52840 and nRF5340.
Add this via a new 'reg' block in the relevant QSPI nodes, along with
names for the register blocks so they are easier to retrieve.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Adds a driver using the SNVS high power and optionally low power
RTC instances. A device specific function `mcux_snvs_rtc_set` is
provided to update the current counter value.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
The commit adds "disk-access" property to fstab bindings to allow
selecting FS_MOUNT_FLAG_USE_DISK_ACCESS while defining file
systems in DTS.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This adds an spi master mode driver via bitbanged gpio. Only syncronous
transfers are implemented. Clock signal timing is accomplished via busy
waits, the gpios are manipulated via the standard gpio interface; these
two factors limit the frequency at which it can operate - but here
a simple and generic implementation was chosen over performance.
The driver supports the various clock polarity and phase
configurations, and can also work with word sizes which are non
multiples of 8bits, currently up to 16 bits.
A sample program is also added demonstrating basic use of the driver
with 9bit data words.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Adds optional device tree properties to insert delays between spi chip
select assert/deassert and the clock edges, and also between spi
frames and transfers to the mcux flexcomm spi driver. If the properties
are not set, no additional delay is inserted.
Verified expected behavior on mimxrt685_evk and check with a scope
that the pre- and post-delay could be changed from the device tree
properties.
Signed-off-by: Bryce Wilkins <bryce.wilkins@gmail.com>
This commit adds support for IMX6SX PWM.
The PWM module is the same module present on the IMX7D and so dts
bindings has been renamed following the one present on linux.
Signed-off-by: Antonio Tessarolo <anthonytexdev@gmail.com>
Most of the time SPI devices use TI's frame format. But some may use
Motorola's. This is already taken care of in the SPI API and now it will
be possible to select the right format from DTS. Like:
...
frame-format = <SPI_FRAME_FORMAT_MOTOROLA>;
...
This is only meant to be used for devices supporting both formats (so
the format is not hard-coded in the driver) and selected by hardware
configuration or else. Which, in such case, it will need to use
DT_INST_PROP(<instance number>, frame-format) macro call to retrieve
the property value. Others can fully ignore it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Software reset is already implemented in the driver when the
`reset_gpio` is not defined. However it could not be activated
because the `reset_gpio` is a required field in the DTS
binding.
Signed-off-by: Casper Meijn <casper@meijn.net>
This patch adds support for the new pinctrl API to the UARTE driver. The
old pin property based solution is still kept so that users have time to
transition to the new model.
Notes:
- Some build assertions cannot be performed since the driver does not
have direct access to pin settings anymore. As a result user will not
be notified if HWFC is enabled but RTS/CTS pins are not configured.
- Hardware flow control can be enabled regardless of pin configuration,
it is now up to the user to configure RTS/CTS pins in DT.
- Some RX enable checks that were performed using pin information has
been replaced with a DT property that informs if RX is enabled or not.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add initial support for nRF pin controller driver. The implementation in
this patch does not yet support any peripheral. Only states
representation and basic driver functionality is introduced.
Note:
The nrf_pin_configure function has been marked as __unused since it may
not be used in certain scenarios until all peripherals are supported by
the pinctrl driver. For example, if only UART/E is supported but the
board does not enable UART, the function will never get called. However,
that board will likely have other peripherals that will gain support in
the future.
Thanks to Marti Bolivar for bindings documentation.
Co-authored-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Now that STM32 drivers are using pinctrl API, set pintrl-0 and
pintrl-names properties as required in order to report malformed
nodes description soon at build stage and avoid cryptic
DT api build error messages.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the new pinctrl API to configure pins.
Since STM32F1 series require pinctrl option and required register
address is parent timer address in place of own node register address,
use PINCTRL_DT_INST_CUSTOM_REG_DEFINE in place of usual
PINCTRL_DT_INST_DEFINE for this specific series.
Additionally, remove the automatic selection of PINMUX API.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the new pinctrl API to configure pins.
Additionally, rename usb_pinctrl to usb_pcfg to better fit
new pinctrl API.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the pinctrl state name (default) for the I2C peripherals.
Changes performed based on the script proposed in
"boards: arm: stm32: add pinctrl state name for UART peripheral"
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use nrfx_gpiote and nrfx_ppi allocators to allocate channels
at runtime instead of fixed, device-tree based allocation which
is harder to maintain.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add bindings for a generic PCIe Controller in ECAM mode.
ECAM stands for PCI Express Enhanced Configuration Access Mechanism
where the PCIe config space is flat memory-mapped.
An optional msi-parent phandle is added to link to an optional
MSI/MSI-X Interrupt Message Translation HW component.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce a new RPMsg with static VRINGs backend. This new backend makes
easy to generate and use IPC instances backed by OpenAMP using the DT.
Each instance is defined in the DT as (for example):
ipc: ipc {
compatible = "zephyr,ipc-openamp-static-vrings";
shm = <&sram_ipc0>;
mboxes = <&mbox 0>, <&mbox 1>;
mbox-names = "tx", "rx";
role = "primary";
status = "okay";
};
It is then possible to register an send data through endpoints using the
IPC service APIs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
* With existence of Adafruit Qt Py boards, and upcoming wireless
Xiao from Seeeduino, define nexus node and peripheral node
labels for use with shields that accept any Xiao format board.
* Adds `&xiao_d`, `&xiao_spi`, `&xiao_i2c` and `&xiao_serial` generic
node labels.
* Add new 'seeed-xioa-header.yaml` to document new nexus node.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
Add a pin control driver for GD32 SoCs using the AFIO model.
Thanks to Gerson Fernando Budke for testing and implementation
suggestions.
Co-authored-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
1.Putting the PWM_CHANNEL_X, PWM_PRESCALER_CX information
in the description.
2.Use the common definition EC_FREQ.
3.Use the common macro IT8XXX2_DT_ALT_ITEMS_LIST.
4.Stop using DRV_CONFIG, DRV_REG macro.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Users will have to include dt-bindings/spi/spi.h in order to use the
relevant flags fol this property. For instance:
...
duplex = <SPI_HALF_DUPLEX>;
....
By default all SPI device are configured to be full duplex so the
property is optional. This property makes sense only for devices that
can be configured on either modes. Which, in such case, it will need to
use DT_INST_PROP(<instance number>, duplex) macro call to retrieve the
property value. Others can fully ignore it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add tests for the instance based enum macros DT_INST_ENUM_IDX and
DT_INST_ENUM_IDX_OR.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
IT8XXX2 uses shared ns16550.c driver which does not provide a power
management callback(pm_action_cb), so create driver to handle
IT8XXX2 specific UART features.
note: pm_action_cb(old name: pm_control_fn)
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Prescaler was misplaced in pwm binding, instead of timers binding.
For example, TIM6/TIM7 doesn't have PWM capability,
but have a prescaler.
Also prescaler is common to all PWM channels of the same timer.
This change also prepares the introduction of timer based counter
(which requires prescaler at timer level)
For compatibility reason temporarily keep pwm binding to avoid
breaking boards out of tree.
Block st,prescaler property in lptim binding
as lptim doesn't use this property for now.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
This will be used to take a phandle to a FEM device, either a generic
two pin device or an nRF21540. Keep the nRF21540 binding example up to
date.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The way the nRF21540 device is configured makes sense once you
understand it, but it's quite unusual: a single peripheral is
configured with two separate devicetree nodes linked by a phandle.
Since this risks entering "exploding head" territory for beginners, it
deserves a thorough example. Add one to the binding's description.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This is a helper binding for radio front-end modules that have a
two-pin control interface, where one pin is used to turn on an power
amplifier (PA) for TX, and another is used to turn on a low-noise
amplifier (LNA) for RX.
Such hardware is already supported by the Bluetooth subsystem, but via
PA/LNA Kconfig settings. Since this is hardware configuration, it is
better to move this to devicetree instead.
Add a binding that makes it possible to define nodes which contain the
same information, along with a bit of extra information related to the
gain in dB of each amplifier not currently available from Kconfig.
This is similar to the existing binding for the nordic,nrf21540-fem
compatible.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Andrzej Kuros <andrzej.kuros@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This is to support upcoming external radio coexistence implementations,
see binding documentation for more info.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
add ledc to board dtsi file,
change compatible and device define in pwm driver,
add yaml for board ledc support,
fix missing include for board in gpio include
Signed-off-by: Andrei-Edward Popa <andrei_edward.popa@upb.ro>
Use i2c_hal functions to enable support for
multiple SoCs.
Use DT compat to enable I2C from device
tree configuration
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
This joins all clock control handling to same source
by using hal clock functions. It also brings ESP32C3
clock support.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
In order to have Espressif SoCs working with
the same uart drivers, all low level functions
are now replaced to hal_espressif HAL calls.
This also changes pinmux, gpio and uart
init order to meet its dependencies.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
STM32WL could be either single core (stm32wlex) or
dual core (stm32wl5/4x).
Make CPU2 prescaler an optional property (while it will
be required if inherited from st,stm32wb-rcc.yaml.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that Kconfig option for STM32 clocks configuration has been
removed, set rcc properties as required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added watchdog implementation which is using counter device
to implement watchdog driver API. Watchdog timeout is called from
counter interrupt context. Some counter implementations support
using ZLI interrupt level which can be use here as well. Watchdog
like this can be used along hardware watchdog to cover for its
limitations, i.e. Nordic watchdog resets unconditionally after
62uS after triggering watchdog interrupt. It is not enough time
to dump logging data.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The FIU/UMA module in the NPCX chip provides an dedicated SPI interface
to access the SPI flash. This commit adds the driver support for it.
With this commit, the application can call the flash APIs
(via spi_nor.c) to access the internal flash of NPCX EC chips.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Change-Id: I32bbf09f6e014b728ff8e4692e48151ae759e188
Rewrite the NRFX IPC driver to properly support multi-channel addressing
leveraging the newly introduced MBOX APIs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
One limitation of the current IPM API is that it is assuming that the
hardware is only exporting one single channel through which the data can
be sent or signalling can happen.
If the hardware supports multiple channels, the IPM device must be
instantiated (possibly in the DT) several times, one for each channel to
be able to send data through multiple channels using the same hw
peripheral. Also in the current IPM API only one callback can be
registered, that means that only one driver is controlling all the
signalling happening on all the channels.
This patch is introducing a new MBOX API that is supporting
multi-channel signalling and data exachange leveraging and extending the
previous (and outdated) IPM API.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This is a driver for the Synopsys DesignWare MAC. It should work
with the "DesignWare Cores Ethernet Quality-of-Service" versions 4.x
and 5.x.
This driver uses a zero-copy strategy, meaning that the hardware
reads and writes data directly from/to packet fragment buffers
provided by the network subsystem without first copying the data into
a dedicated DMA bounce buffer.
Platform specific setup is necessary for the hardware to work.
Currently, only the STM32H7X series is implemented and tested.
While this part needs refinement, this driver performs better and uses
far less code space than the HAL-based alternative.
Not yet implemented:
- MDIO (it is WIP, currently relying on default PHY config)
- PTP support
- VLAN support
- various hardware offloads (when available)
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
MEC172x eSPI driver, eSPI pin programming, interrupt updates related
to eSPI and other updates for MEC172x eSPI driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add a set of tests to check the API behavior. The API tests can only run
on a platform that does not have an actual pinctrl driver, e.g.
native_posix. The test itself implements a pinctrl mock driver and
provides the required "pinctrl_soc.h" header with required types/macros.
The implementation is used in the tests to verify the behavior of the
API or Devicetree macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
When using group based representation on pinctrl nodes, the pin
configuration properties end up being at the grand-children level, so
the `pincfg-node.yaml` file can't be used.
Having a common file that can be used for both cases would require
tooling changes, so for now a copy that operated at the grand-children
level has been created.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Initial skeleton for pinctrl drivers. This patch includes common
infrastructure and API definitions for pinctrl drivers.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move odr options from Kconfigs to Device Tree. Moreover add
in DT a power-mode option to select among 4 possible values
(PD, LP, HR, HF). The power mode cannot be currently set from
sensor APIs.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
