drivers/sensor: lps22hh: Move odr Kconfig property into dts
Move odr options from Kconfigs to Device Tree. Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit is contained in:
parent
9c98d2c615
commit
56b435f2bf
4 changed files with 24 additions and 22 deletions
|
@ -52,24 +52,4 @@ config LPS22HH_THREAD_STACK_SIZE
|
|||
help
|
||||
Stack size of thread used by the driver to handle interrupts.
|
||||
|
||||
menu "Attributes"
|
||||
|
||||
config LPS22HH_SAMPLING_RATE
|
||||
int "Output data rate"
|
||||
range 0 7
|
||||
default 0
|
||||
help
|
||||
Sensor output data rate expressed in samples per second.
|
||||
Data rates supported by the chip are:
|
||||
0: ODR selected at runtime
|
||||
1: 1Hz
|
||||
2: 10Hz
|
||||
3: 25Hz
|
||||
4: 50Hz
|
||||
5: 75Hz
|
||||
6: 100Hz
|
||||
7: 200Hz
|
||||
|
||||
endmenu
|
||||
|
||||
endif # LPS22HH
|
||||
|
|
|
@ -171,9 +171,11 @@ static int lps22hh_init_chip(const struct device *dev)
|
|||
|
||||
LOG_DBG("%s: chip id 0x%x", dev->name, chip_id);
|
||||
|
||||
ret = lps22hh_set_odr_raw(dev, CONFIG_LPS22HH_SAMPLING_RATE);
|
||||
/* set sensor default odr */
|
||||
LOG_DBG("%s: odr: %d", dev->name, cfg->odr);
|
||||
ret = lps22hh_set_odr_raw(dev, cfg->odr);
|
||||
if (ret < 0) {
|
||||
LOG_ERR("%s: Failed to set sampling rate", dev->name);
|
||||
LOG_ERR("%s: Failed to set odr %d", dev->name, cfg->odr);
|
||||
return ret;
|
||||
}
|
||||
|
||||
|
@ -237,6 +239,7 @@ static int lps22hh_init(const struct device *dev)
|
|||
LPS22HH_SPI_OPERATION, \
|
||||
0), \
|
||||
}, \
|
||||
.odr = DT_INST_PROP(inst, odr), \
|
||||
COND_CODE_1(DT_INST_NODE_HAS_PROP(inst, drdy_gpios), \
|
||||
(LPS22HH_CFG_IRQ(inst)), ()) \
|
||||
}
|
||||
|
@ -258,6 +261,7 @@ static int lps22hh_init(const struct device *dev)
|
|||
.stmemsc_cfg = { \
|
||||
.i2c = I2C_DT_SPEC_INST_GET(inst), \
|
||||
}, \
|
||||
.odr = DT_INST_PROP(inst, odr), \
|
||||
COND_CODE_1(DT_INST_NODE_HAS_PROP(inst, drdy_gpios), \
|
||||
(LPS22HH_CFG_IRQ(inst)), ()) \
|
||||
}
|
||||
|
|
|
@ -33,6 +33,7 @@ struct lps22hh_config {
|
|||
const struct spi_dt_spec spi;
|
||||
#endif
|
||||
} stmemsc_cfg;
|
||||
uint8_t odr;
|
||||
#ifdef CONFIG_LPS22HH_TRIGGER
|
||||
struct gpio_dt_spec gpio_int;
|
||||
#endif
|
||||
|
|
|
@ -11,3 +11,20 @@ properties:
|
|||
This pin defaults to active high when produced by the sensor.
|
||||
The property value should ensure the flags properly describe
|
||||
the signal that is presented to the driver.
|
||||
|
||||
odr:
|
||||
type: int
|
||||
required: false
|
||||
default: 0
|
||||
description: |
|
||||
Specify the default output data rate expressed in samples per second (Hz).
|
||||
Default is power-down mode
|
||||
enum:
|
||||
- 0 # Power-Down
|
||||
- 1 # 1Hz
|
||||
- 2 # 10Hz
|
||||
- 3 # 25Hz
|
||||
- 4 # 50Hz
|
||||
- 5 # 75Hz
|
||||
- 6 # 100Hz
|
||||
- 7 # 200Hz
|
||||
|
|
Loading…
Add table
Add a link
Reference in a new issue