These are a direct copy from the nrf51_pca10028 board, since it's also
an nRF51 and has the same size flash.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The allowed values for APB2 prescaler are: 1, 2, 4, 8, 16.
Set APB2 prescaler value to 1 in boards defconfig.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The NFFS partition at the end of flash is also useful for any other
file system or even the Flash Circular Buffer (FCB). Rename the
partition from 'nffs_partition' to 'storage_partition' and make it
depend on a new hidden Kconfig entry which the relevant users will
select (such as NFFS and FCB).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To prepare to upcoming dtc v1.4.6, fix warnings in dts files.
This commit addresses the following warning:
"unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property in /gpio_keys".
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In some BLE use cases, using MSI driven SYSCLK is required.
Rework board Kconfig.defconfig in order to enable use of 2
alternate default clock configurations.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We have been combining imported mcux drivers into a flattened directory
structure to maximize driver reuse, but the introduction of additional
nxp soc families (lpc and imx) to zephyr has introduced driver naming
conflicts. This caused us to rename and modify imported files, such as
fsl_gpio.c/h, to make them unique across all three nxp soc families.
This makes updating the the mcux drivers complicated, especially for the
lpc family.
Reoganize the mcux drivers into soc family subfolders, so we can just
copy all the drivers from an mcux distribution (which is done on an
soc-basis) into the appropriate soc family folder. Undo all of the
naming changes that occurred when lpc and imx drivers were originally
imported. Undo the accidental squashing of the kinetis watchdog and dcdc
drivers that occurred when the imx drivers were introduced.
The drawback to this approach is that we have duplicate files when the
same hw ip modules exist in multiple soc families, however there are
only few cases where this occurs, such as fsl_lpuart and fsl_trng.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes#7137
Enables the i2c drivers for these boards.
Required to enable i2c with these boards.
Tested samples/bluetooth/beacon for nrf52_pca10040
with i2c enabled.
Parameters used for enabling i2c:
CONFIG_I2C=y
CONFIG_I2C_0=y
CONFIG_I2C_NRF5=y
CONFIG_I2C_NRF5_0_GPIO_SCL_PIN=6
CONFIG_I2C_NRF5_0_GPIO_SDA_PIN=7
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.com>
Adds led and button dts nodes to all kinetis boards and removes the
now unused preprocessor macros from board.h.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update names of the configuration entries so that the new nRF SPIS
driver can be used on this board.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The test "net/utils" fails to build on nucleo_f103rb
due to "region `SRAM' overflowed by 8 bytes.
Disabling PWM at the board level to build the test.
Moreover, according to issue #6858, we will only configure
board valuable HW and connectors on board level and the
user should enable what is needed on application level.
Reported-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Underscore ('_') isn't a valid char for alias names based on the device
tree spec. Newer dtc compilers flag this as a warning so lets clean it
up. Replaced '_' with '-' to keep things simple.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The TRNG IP block in the KW41Z is really an entropy source and not
intended to be used as a general purpose random number generator
source. The block has 15 slots to read from and when the last slot
is read it has to regenerate the 15 numbers. This process takes
3-5 seconds and is blocking. The change here is to use the TRNG as
an entropy source to the XOROSHIRO pseudo random number function
and then have the KW41Z use XOROSHIRO for random number generation.
Signed-off-by: David Leach <david.leach@nxp.com>
The Colibri iMX7D Computer on Module with Colibri Evaluation Board
configuration supports the following hardware features on the Cortex M4
Core:
+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component |
+===========+============+=====================================+
| NVIC | on-chip | nested vector interrupt controller |
+-----------+------------+-------------------------------------+
| SYSTICK | on-chip | systick |
+-----------+------------+-------------------------------------+
| UART | on-chip | serial port-polling; |
| | | serial port-interrupt |
+-----------+------------+-------------------------------------+
The default configuration can be found in the defconfig file:
boards/arm/colibri_imx7d_m4/colibri_imx7d_m4_defconfig
Other hardware features are not currently supported by the port.
Connections and IOs:
The Colibri iMX7D Computer on Module with Colibri Evaluation Board
was tested with the following pinmux controller configuration.
+---------------+-----------------+---------------------------+
| Board Name | SoC Name | Usage |
+===============+=================+===========================+
| UART_B RXD | UART2_TXD | UART Console |
+---------------+-----------------+---------------------------+
| UART_B TXD | UART2_RXD | UART Console |
+---------------+-----------------+---------------------------+
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
All boards based on STM32 should use dts for I2C and SPI.
Move CONFIG flags selection from boards to arch and select them
for all STM32 SoCs.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We run the same tests over and over again in different qemu
environemnt. Optimize the list to reduce redundant testing of the same
protocols. Picked qemu_x86 because it has userspace enabled.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A Kconfig option is added for setting the initialization priority.
This is done to make the initialization priority requirements in
nrf52_pca20020 board power up sequence clearer.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
A documentanion file is added for Thingy:52. This document only
discusses the currently supported features of the board. The omissions
include the audio features and sensors which don't have a working driver
in tree.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
A new board configuration is added for Thingy:52, also known as
PCA20020. This includes support for some of the on-board sensors, and
other peripherals such as the on-board GPIO expander.
The board power rail sequencing is also implemented, as the rails need
to be powered up in a correct order and before certain device driver
init calls are made.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
The test "net/utils" fails to build on olimexino_stm32
due to "region `SRAM' overflowed by 192 bytes".
Disabling I2C and SPI on board level the test build fine.
Moreover, according to issue #6858, we will only configure
board valuable HW and connectors on board level and the
user should enable what is needed on application level.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
As we have E70 ethernet driver enabled, we need to enable the
generic ethernet L2 driver too so that the ethernet is actually
useful.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The SAM0 SoC was switched to use DTS for SPI configuration. Update
documentation for the SAM0 based boards to use the correct SPI
controller device names.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
As the board has ethernet chip it makes sense to enable the
ethernet support by default.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Upcoming Nordic ICs that share many of the peripherals and architecture
with the currently supported nRF5x ones are no longer part of the nRF5
family. In order to accomodate that, rename the SoC family from nrf5 to
nrf, so that it can contain all of the members of the wider Nordic
family.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
New revision (SWCU117H) got published and the old one (supposedly
SWCU117G) is no longer available.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Currently, it seems that only boards with smaller amount of RAM
get a value for "ram" property, and very few boards have "flash"
defined. However, to test bigger sample applications, it's helpful
to have these properties universally defined.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Added support for Waveshare BLE400 board.
Tested it with the following samples and confirm it work.
- samples/basic/blinky
- samples/basic/button
- samples/basic/fade_led
- samples/basic/threads
Signed-off-by: Roman Tataurov <diytronic@yandex.ru>
Describe in documentation few methods that can be used by
users to flash the ArgonKey with a binary image.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Move the dts.fixup back to board dir in prep for support mps2_an521.
The memory maps between the two mps2_an385 and mps2_an521 differ greatly
so its easier to just keep the fixup files with the board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add initial support for NUCLEO-L073RZ board.
This is a typical Nucleo-64 board, so most files are reused
from already supported Nucleo boards with small changes.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
SoC dts fixups are added and the i2c_nrf5 driver is modified to use
the values generated from the device tree.
The I2C_*_DEFAULT_CFG and I2C_*_IRQ_PRI options are removed from board
defconfigs. Bitrate and IRQ priority are configured using using the
device tree instead.
HAS_DTS_I2C is selected on all nrf5 boards to prevent generation of
conflicting defines from Kconfig.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
The i2c controller nodes are enabled in the board specific dts files
on boards where the controller was enabled in the board Kconfig.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
This commit changes the Arduino Zero pinmux configuration to use PA12
as MISO.
According to the schematic, the Arduino Zero provides a SPI bus on
SERCOM4 with the following pads/pins:
- MISO: PA12/pad0 (pin 21)
- MOSI: PB10/pad2 (pin 19)
- SCK: PB11/pad3 (pin 20)
The MISO signal is incorrectly labeled as PB12_S4_SPI_MISO on the
schematic. It should be labeled PA12_S4_SPI_MISO.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Nucleo-64 boards do not have X3 crystal by default, so HSE is clocked
from MCO output of ST-LINK, and CONFIG_CLOCK_STM32_HSE_BYPASS should be
enabled. STM32F0 HSE somehow magically works even without that, but
to do so is the right thing.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Since not all boards enable all devices, we typically have the SoC dtsi
file have a device marked with status = "disabled" and have the
board.dts explicitly enable with status = "ok". Update it so USB on
Atmel SAMD21 work this way.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move IRQ numbers into device tree so we can remove soc_irq.h. We are
already using IRQ defines generated form the DTS so no point in having
soc_irq.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added device tree support to the ARM SBCon I2C controller. We utilize
the compatiable "arm,versatile-i2c" the binding from Linux for the some
peripheral block.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The legacy SPI API was turned back on for the Adafruit Feather M0
Basic Proto when the SAM0 SoC was switched to using DTS for SPI. This
commit turns it back off.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
ArgonKey board is a 96boards sensor hub platform for all 96Boards
compliant family products. The ArgonKey packs a Cortex-M4 chip
together with a set of motion, environmental and ambiental sensors
and can be used as a development platform for many different
applications.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Switch the SoC device tree to define a single entry per SERCOM instead
of one per mode.
Define a Device Tree binding for the SAM0 SPI and use it instead of
Kconfig for enabling / disabaling instances
Switch the Arduino Zero, Adafruit Feather M0 Basic Proto, and
Trinket M0 to use the new defintion.
Add the APA102 LED that's on the Trinket as a test.
Signed-off-by: Michael Hope <mlhx@google.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Changed the default UART used for the console. You used to have to
use wires on the J4 header. Now you can use the UART provided by the
Segger USB composite device.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Fixed the output string in the documentation for
the SAM E70 Xplained. The output for the hello_world
sample wasn't correct.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Support the ST STM32F0DISCOVERY board with STM32F051R8T6 SoC
Tested with:
- `samples/basic/blinky`
- `samples/basic/button`
Includes flash config in `stm32f0_disco.rst` for use with mcuboot
Signed-off-by: Nathan Tsoi <nathan@vertile.com>
The Feather M0 Basic Proto is an Atmel SAMD21 based development board
with USB, UART, SPI, LED and onboard lithium polymer battery charger.
Use of the Adafruit stock photo (adafruit_feather_m0_basic_proto.jpg)
for the board documentation was approved by Adafruit Industries.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
As USB port is present on the board, and pinmux configured,
add USB support in board dts file.
Configure Ethernet oer USB as default net i/f
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
According to STM32-E407.pdf (Revision I, June 2017), CON1 RST is
connected to processor pin #25, not #23.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
The arm qemu platform has limitiations as we get into more complicated
features like userspace support. Add one hardware platform to catch
issues in sanitycheck for development of such features.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/arm/soc/<SOC>/dts.fixup so
we remove duplication in the boards and only have board specific
defines in boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The space referred to in these comments was once truly reserved for
the application: no zephyr partition would ever use it.
Now, though, that's not the case, since NFFS will use these sectors
when enabled.
Just delete the comments.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Let's point users at the latest documentation on flash
partitions from each of the board files, rather than duplicating some
of the information in it.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
Move common SoC dts.fixup defines into
arch/arm/soc/atmel_sam/<BAR>/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/arm/soc/nxp_imx/rt/dts.fixup
so we remove duplication in the boards and only have board specific
defines in boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/kwx/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/kl2x/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_lpc/lpc54xxx/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/k6x/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implements interrupt driven UART for the serial driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Move common SoC dts.fixup defines into
arch/arm/soc/ti_simplelink/<BAR>/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Current configuration was choosen to avoid colliding with existing ones
for i2c and uart, but others can be used.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Current configuration was choosen to avoid colliding with existing ones
for i2c and uart, but others can be used (see
drivers/pinmux/stm32/stm32_f0.h)
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Configure SPI using DT for the following STM32 boards:
96b_neonkey
nucleo_f091rc
nucleo_f334r8
nucleo_f401re
nucleo_l432kc
nucleo_l476rg
SPI nodes in <board>.dts file are populated matching boards existing
pinmux default configuration and enabled in Kconfig.defconfig if
SPI is enabled.
For nucleo_l476rg board SPI2 and SPI3 nodes are not yet added, because
of missing pinmux defines.
Fixes#5836
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Commit 247782a7b3 moved the sam0 UART
and SPI configuration into pinmux. Using these drivers without pinmux
causes the kernel to skip the pin configuration.
Tested on arduino_zero.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Remove spurious console code block to fix formatting of the following
zephyr-app-commands directive. While I am here, fix the indentation of
the two zephyr-app-commands directives.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Atmel SAMD21 series was classified too broadly as SAMD.
This patch names it correctly to make room,
for other members of SAMD series
Signed-off-by: Sean Nyekjaer <sean@nyekjaer.dk>
Also pull out the SERCOM pads configuration to defines. Note that the
SAM0 has a two level configuration - a signal (like TX) is mapped to a
pad, and then a pad is mapped to a function on a pin.
Signed-off-by: Michael Hope <mlhx@google.com>
nucleo_f413zh was missing some files to support flash with
openocd. Fix this lack and update doc.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
nucleo_f412zg was missing some files to support flash with
openocd. Fix this lack and update doc.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
CONFIG_I2C_NRF5_GPIO_SDA_PIN and CONFIG_I2C_NRF5_GPIO_SCL_PIN are
replaced with port specific versions. Board defconfigs relying on the
original names are updated. The driver is also modified to pass the
configure values to registers.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Pin multiplexing is a function of the PORT peripheral. This change
defines a separate pinmux device at the same address as the PORTs
themselves.
Signed-off-by: Michael Hope <mlhx@google.com>
Adds dts nodes and fixups for the fxos8700, fxas21002, and max30101
sensors to the hexiwear_k64 board. Tested with:
- samples/sensor/fxos8700
- samples/sensor/fxas21002
- samples/sensor/max30101
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts nodes and fixups for the fxos8700 sensor to the frdm_kw41z
board. Tested with samples/sensor/fxos8700
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts nodes and fixups for the fxos8700 sensor to the frdm_k64f
board. Tested with samples/sensor/fxos8700
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hts221 sensor driver was implicitly made dependent upon the
disco_l475_iot1 board when it was converted to dts, so build the
associated sample only for this board. This issue was encountered when
adding sensor dts support to nxp boards, which don't have hts221.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
We should enable CONFIG_POLL on application level when
we want to use SPI transceive_async() function.
This patch removes it from disco_l475_iot1 default
configuration.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The jlink commander failed to program flash with auto speed on the
usb_kw24d512 board, so set the speed explicitly on this board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that the jlink runner supports the flash command, set
BOARD_FLASH_RUNNER when the OpenSDA or LPCLink debug adapter is
programmed with jlink firmware.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enable and configure I2C1.
This configuration enables ready to use compatibility
with expansion shields based on Arduino type connectors
Additionally, fix comment on clock speed in board _defconfig
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Applies to #4008 and #5159 for this board. Problem is that the
button interrupt callback was only firing once. Solution is to
set the pin pull up flag to GPIO_PUD_PULL_UP.
Signed-off-by: Anders Pitman <tapitman11@gmail.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This moves and merges the existing board-level dts.fixup files
for STM32 L4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
disco_l475_iot1 boards fixup blocks for devices connected via SPI
and I2C stay in board level dts.fixup file, because they are board
specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F3 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F1 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
96b_carbon boards fixup block for Bluetooth HCI device via SPI
stays in board level dts.fixup file, because it is board specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F0 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
When we updated the Nordic SoCs for getting flash controller label/name
from dts, we missed updating the 96b_nitrogen/dts.fixup file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
So far, DT did not support the flash driver name.
Any flash-controller should have the appropriate
flash driver that should be identified by its name.
This path adds generic support for extract the description
from the flash-controller node,
adds implementation of this property for all nrf5x targets.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Move bluetooth module SPI port related configuration
to dts and generate dts based defines on 96b_carbon
and disco_l475_iot1.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
references to pdf files (e.g.,
www.st.com/resource/en/reference_manual/dm00091010.pdf)
were missing the http:// prefix so looked like a relative reference.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Adding 'config POLL' in Kconfig.defconfig creates a dependency
between CONFIG_POLL and board BOARD_DISCO_L475_IOT1 & SPI.
Remove this definition from the file and set CONFIG_POLL
in board _defconfig file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In Qemu 2.10 we can run this board configuration in Qemu directly. Make
this possible by setting the board configuration to allow emulation.
Until we have the latest QEMU in the SDK this can be used with a recent
QEMU like this:
$ mkdir build; cd build
$ cmake -DQEMU=/usr/bin/qemu-system-arm -DBOARD=mps2_an385 ..
$ make run
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some boards are supported natively by qemu. This option will allow us to
run tests using those platforms directly without having to go via a
dedicated qemu board definition.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In order to be able to document the build on Windows and UNIX
systems, slight variations are required on the app commands
that are used throughout the documentation system.
This includes getting rid of the prompt symbol and providing commands
for both UNIX and Windows operating systems.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Most boards enable the pinmux by default by setting CONFIG_PINMUX=y in
<board>_defconfig, but several boards did it in Kconfig.defconfig
instead. Several code reviews, such as #5043, have suggested using a
select in Kconfig.board to enable the pinmux, however this caused
warnings:
warning: (BOARD_LPCXPRESSO54114) selects PINMUX which has unmet direct
dependencies (BOARD_FRDM_K64F || BOARD_FRDM_KL25Z || BOARD_FRDM_KW41Z ||
BOARD_HEXIWEAR_K64 || BOARD_USB_KW24D512 || BOARD_GALILEO)
Fix how these boards enable the pinmux so they are more consistent with
other boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Defining TRIGGER_MODE choices in board Kconfig.defconfig files
brings unwanted dependency and warning messages when using sensors
on other boards.
Change sensor configuration by enabling wanted trigger choice rather
than redefining choice.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Updated previously broken links to emulation setup install, instructions
and Getting Started Guide.
Also added a few clarifications for the prerequisites setup.
Fixes#5601
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Instead of accessing the environment variable ZEPHYR_BASE every time we
require accessing the source code root, use an intermediate variable
that has OS path separators correctly set to '/' to avoid issues on
Windows.
Note: This removes the ZEPHYR_SOURCE_DIR CMake variable. External
applications using that will need to change to use the new ZEPHYR_BASE
variable.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Old reference on driver's specific raw mode was still lurking around.
Removing those.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This was validated on the cc3220sf_launchxl board
using the Zephyr thermometer sample program
adapted to call the i2c driver directly, and fetching
samples from the on-board TMP006 temperature sensor.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
ETH_MCUX_0 needs to be turned on when CONFIG_NET_L2_ETHERNET is enabled.
If CONFIG_NET_L2_ETHERNET is disabled (e.g. when configured for 6loble),
then ETH_MCUX_0 should remain disabled.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
This board doesn't support `make flash` way of programming.
So, remove that from documentation.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Of these, only struct net_ipv6_nbr_data::send_ns is a descriptive
change:
send_ns is used for timing Neighbor Solicitations in general, not
just for DAD.
The rest are typo/grammar fixes.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Update board definitions with supported feature. This is temporary
until we have full coverage for device drivers in DTS, then we can use
DTS instead.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use the existing J-Link functionality to support debugging nRF5x targets
with GDB over a Segger J-Link USB connection.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
ST official reference for this board is B-L475E-IOT01A.
While not used in zephyr, add reference in documentaion title.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable DT support in the dfu-util flasher when the target is a
DfuSe (DFU + ST extensions) device.
Untangling DfuSe-specific options (currently, the default is 'leave',
to immediately start running after the flashing is done) from the
actual address makes this cleaner, and sets up a subsequent patch to
let callers set DfuSe options.
It also lets us fix an unnecessary printline when flashing DfuSe
devices. There's no need to reset those, since the 'leave' modifier
starts execution immediately.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The various runners (flash/debug scripts) use environment variables to
take arguments. This is legacy behavior which is not desirable.
Use command line arguments instead.
Note: this leaves more general environment variables with publicly
documented behavior in place for now, for compatibility, e.g.:
ZEPHYR_FLASH_OVER_DFU, OPENSDA_FW, ESP_IDF_PATH, PYOCD_DAPARG
For example, when using dfu-util to flash arduino_101, instead of
setting DFUUTIL_PID, DFUUTIL_ALT, and DFUUTIL_IMG environment
variables, have the script invocation look like this:
python3 .../zephyr_flash_debug.py dfu-util flash \
[common arguments omitted] \
--pid=8087:0aba --alt=x86_app \
--img=.../build/zephyr/zephyr.bin
Make similar changes for other runners (openocd, etc.) and
targets (debug, debugserver).
To implement this in the scripts:
- have the individual scripts/support/runner/some-runner.py files
register their own command line arguments
- teach them to construct instances from arguments, not the
environment
- have zephyr_flash_debug.py request runners to register command
line argument parsers, and handle arguments
In the build system:
- add a new board_runner_args() extension function that board.cmake
files can use to add to the zephyr_flash_debug.py command line
- adjust cmake/flash/CMakeLists.txt to invoke with arguments
- add new helper include files for each runner (like
boards/common/dfu-util.board.cmake, etc.), which add default
options as needed and then add on overrides from
board_runner_args() calls
- update board.cmake files to use the new includes and extension
This implied some tweaking when using openocd to make the CMake string
escaping and unescaping work properly.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
The Python-based runners have replaced the old shell scripts. Refactor
the build system accordingly:
- FLASH_SCRIPT is now BOARD_FLASH_RUNNER
- DEBUG_SCRIPT is now BOARD_DEBUG_RUNNER
The values, rather than being the names of files, are now the names of
runners in scripts/support/runner. They are still short, descriptive
names like "openocd", "jlink", "em-starterkit", etc.
Adjust the zephyr_flash_debug.py call and runner internals
accordingly. Have each runner class report a name and the commands it
can handle. This lets us move some boilerplate from each do_run()
method into the common run() routine, and enables further improvements
in future patches.
The handles_command() method is temporary, and will be replaced by a
more general mechanism for describing runner capabilities in a
subsequent patch. The initial use case for extending this is to add
device tree awareness to the runners.
To try to avoid user confusion, abort the configuration if an
xxx_SCRIPT is defined.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
To avoid configuration surprises, replace
CONFIG_CLOCK_STM32_PLL_SRC_HSI
with
CONFIG_CLOCK_STM32_PLL_SRC_HSI=y
No impact today, but could depend on tools.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On stm32f3_disco pins PF0/PF1 are used for OSC_IN/OSC_OUT
signals. Use pins PA9/PA10 for I2C_2 port
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Enable USB OTG support for olimex stm32-e407 and stm32f407g_disc1
boards by adding USB OTG to the pinmux table. Also, fix out of
range endpoint addresses in CDC ACM case for STM32F4 based boards.
Signed-off-by: Sudarsana Nagineni <sudarsana.nagineni@intel.com>
This board doesn't support the 'flash' goal, which was mistakenly
included during the CMake conversion.
Signed-off-by: Marti Bolivar <marti@opensourcefoundries.com>
External serial flash on this board is 4MB.
Previously, this was confused with internal flash, which is 1MB.
Fixes#1270
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The following files didn't have any copyright or license headers on them
when they got contributed. So add the SPDX Apache license and
appropriate copyright info:
boards/arm/stm32l476g_disco/pinmux.c
samples/basic/threads/src/main.c
tests/net/socket/tcp/src/main.c
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added Inter-IC Sound driver (based on SSC module) for Atmel
SAM MCU family.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-2509
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The kernel timer frequency was incorrectly set to the system clock
frequency (528 MHz) instead of the core clock frequency (600 MHz).
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Not all boards require the various binary formats zephyr generates. So
be selective based on the arch, SoC or board and only geenrate the
binaries actually needed.
Fixes#5009
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add configuration, pinmux, dts and documentation for the STM32L476G
Discovery board based on the STM32L476VG SoC.
Signed-off-by: Arthur SFEZ <arthur.sfez@gmail.com>
The '=' character was incorrectly getting passed to the JLinkGDBServer
device argument, and caused the server to fail to connect to the target.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Rename the Atmel SAM I2C driver based on TWIHS module to match the
convention:
<driver class>_<SoC family>_<hardware module used by the driver>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
olimexino_stm32 was not getting the flash base address from the Kconfig
variable. Since the board uses DTS that will get set, so we can use the
standard openocd.board.cmake.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Unlike other NXP SoCs currently in Zephyr, the mimxrt1052 has the ARM
MPU rather than the NXP MPU. Start out by enabling it with a simple set
of memory regions for "flash" (ITCM), "ram" (DTCM), and the peripheral
buses. More regions will need to be added when we implement support for
external memories.
Tested with:
- samples/mpu/mpu_stack_guard_test
- tests/kernel/mem_protect/protection
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds support for the NXP MIMXRT1050-EVK board, an entry-level
development board for the new mimxrt1052 Cortex-M7 SoC.
Adds pinmuxing, dts, documentation, and jlink debug support for the new
board. Note that pinmuxing uses the mcux pinmux driver directly rather
than the Zephyr pinmux interface. The mimxrt1052 SoC has complicated
pinmuxing that may require changing the Zephyr pinmux interface to
support, so for now let's use the mcux driver directly.
We are also not yet configuring the external flash, therefore a debugger
is required to load code to the internal sram. The on-board OpenSDA
circuit with jlink firmware is sufficient, and the 'make debug' build
target is supported.
Samples tested include: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
the current zephyr sdk now includes openocd configurations for l4
boards, we can now update the boards and docs to reflect this
Signed-off-by: Arthur SFEZ <arthur.sfez@gmail.com>
The old way of constructing FLASH_SCRIPT_ENV_VARS was corrupting the
values that were passed to the flasher. This new method is the
standard way of creating a dictionary/hashmap in CMake and does not
suffer from the same problem.
This fixes
https://github.com/zephyrproject-rtos/zephyr/issues/4844#event-1334599401
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the dts fixup files into the board dir so that board ports can be
more standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Due to copy paste issue, doc file for board nucleo_f030r8
had wrong file name.
Fix it with correct doc name
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
I2C_1 is enabled in board's DT file but we need to enable
it also in boards default config.
I2C_0 doesn't exist in STM32L475 SOC.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Provide default settings in disco_l475_iot board for following
sensors: LSM6DSL, LIS3MDL, LPS22HB, HTS221.
Sensors are disabled by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This should clear up some of the confusion with random number
generators and drivers that obtain entropy from the hardware. Also,
many hardware number generators have limited bandwidth, so it's natural
for their output to be only used for seeding a random number generator.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Add board configuration, dts and pinmux, based on
arm/stm32f4_disco and arm/nucleo_f411re boards.
Error free tests are executed on eval board with the following
sample applications:
- hello_world
- blinky-sample
- button-sample
- console_echo_sample
- console_getchar_sample
Signed-off-by: Jose F. Fernandez <jffernandez@fenix-es.com>
We shouldn't select BOARD_DEPRECATED but set a string with the release
version that the board will get removed in.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
nucleo_f030r8 fails in CI because applications need
more RAM.
Reduce kernel memory used by stacks and ISR vector table.
Fixes#3923
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The original developer no longer has a working board and isn't
interested in maintaining support for the board. Mark the board
deprecated for now and see if anyone wants to pick it up, otherwise will
remove it in a future release.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Match change we made to how I2C is enabled for other stm32 platforms:
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds support for TI Simplelink MSP-EXP432P401R-LAUNCHXL
development board based on Cortex M4 family
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This requires openocd version 0.10 or later.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@linaro.org>
The EFM32 Wonder Gecko Starter Kit contains sensors and
peripherals demonstarting the usage of the EFM32WG MCU
family. This patch add basic support for this board.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Instead of having a board-specific config for this adc test, enable the
required battery-sense circuit by default at the board level when the
adc driver is enabled.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Some our Zephyr tools don't like seeing UTF-8 characters, as reported in
issue #4131) so a quick scan and replace for UTF-8 characters in .rst,
.h, and Kconfig files using "file --mime-encoding" (excluding the /ext
folders) finds these files to tweak.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Move all QEMU related defines to the boards and cleanup xtensa platforms
which were marked to be QEMU capable by mistake.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Default configuration for USART1 (Console output) on board
stm32f3_disco was set on PA9/PA10, which matches Rev-A/B
configuration. Though, on more recent configuration of the
board (Rev-C onward). USART1 is mapped to PC4/PC5.
This configuration has the benefit to support VCP, hence it
is chosen to be set by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable BlueNRJ chip on disco_l475_iot1 board.
Communication with SoC, is done over SPI(3). Hence this
commit enables SPI3 on SoC and configure BT_SPI IRQ,
RESET and CS pins.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add board configuration, dts and pinmux based on both
stm32f469i_disco board and nucleo_f412zg board
Signed-off-by: Massimiliano Cialdi <massimiliano.cialdi@powersoft.it>
Move all STM32 based board pinmux files into the board dirs so we are
consistent across all the STM32 platforms/boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added some clarification on flashing instructions for CC3220SF, in
support of customer issue.
Jira: ZEP-2581
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
BLE is the only networking interface on 96b_carbon, so if
CONFIG_NETWORKING is set, automatically use 6lowpan/BLE link
layer. This will allow to make networking apps work "out of the
box" on 96b_carbon, similar to e.g. qemu_x86 (which automatically
uses SLIP) or frdm_k64f (which automatically uses Ethernet).
This also enables NET_L2_BT_ZEP1656, because most 6LoWPAN/BLE samples
in Zephyr currently use that option, and it is required to achieve
working 6LoWPAN/BLE with Linux kernels currently widely accessible
to the end users. E.g. the latest Ubuntu LTS release, 16.04, ships
with 4.4 kernel, and can be upgraded with a special effort to HWE
kernel which is currently at 4.10. NET_L2_BT_ZEP1656 is needed for
both these kernels.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This reverts commit e1382cc7d6.
Due to restrictive simplelink host driver source licensing.
This also reverts commits based on the simplelink wifi host
driver:
Revert "ext: simplelink: host driver: depend on multithreading"
commit: 4d912b004b
Revert "ext: simplelink: Enable SimpleLink to use Zephyr __errno"
commit: 4e022f7b28
Revert "ext: simplelink: Add SimpleLink DPL porting layer to Zephyr"
commit: 4bc51e67d4
Revert "ext: simplelink: Enable build of the SimpleLink host driver."
commit: 2d2615a49a
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add cross-referenced information on the 96b_carbon and
96b_carbon_nrf51 pages which disambiguates between the two "boards".
Also describe how to flash 96b_carbon_nrf51 with
samples/bluetooth/hci_spi and 96b_carbon with samples/bluetooth/ipsp
to support a Bluetooth HCI stack on 96Boards Carbon (the physical
board).
While we're here, make the documentation page for 96b_carbon match the
format in doc/templates/board.tmpl.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
On 96Boards Carbon, Bluetooth is provided by a secondary nRF51 chip
connected to SPI_1, so enable this peripheral and its driver when BT
is selected.
Similarly, provide BT_SPI_* configs to integrate with the BT HCI SPI
driver. The files these config values apply to only get built when
CONFIG_BT=y, but this configuration can't be handled in the "if BT"
section in 96b_carbon's Kconfig.defconfig. This is because BT_SPI is
a choice value, and thus doesn't support a default setting.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Per ZEP-1958, Phase 2 of adding CC3220sf LaunchXL support,
was to "deprecate the CC3200 launchxl support in Zephyr
(redundant to the CC3220)."
Effectively, the CC3220 SOC replaces the CC3200.
This patch removes the following:
* the imported CC3200 SDK
* CC3200 SOC, board, DTS files.
* adjusts other files where cc3200 was mentioned.
Also, it fixes explicit references to CC3200 in generic
CC32xx driver files.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Rename the BT_CONTROLLER prefix used in all of the Kconfig variables
related to the Bluetooth controller to BT_CTLR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Some boards had HAS_DTS in the defconfig which is dropped if the Kconfig
variable does not have a prompt.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The SimpleLink host driver comes with its own definition of
__errno, which conflicts with Zephyr's definition, but has
a mechanism to enable use of the porting OS's __errno variable.
This patch enables SimpleLink to use Zephyr's __errno
via the DPL porting layer.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
This patch enables and builds the SimpleLink host driver
for Zephyr introduced in a previous patch.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Now that we have an mcux shim driver, remove the old k64-specific
driver. Also remove include/drivers/k20_sim.h, since the old
k64-specific driver was the only thing left using it.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
If the ftm driver is enabled, use an instance routed to the Arduino
header and configure the pinmux accordingly. Unlike the hexiwear_k64,
the pins routed to the RGB led cannot be muxed as ftm channels.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
If the ftm driver is enabled, use the instance routed to the RGB led and
configure the pinmuxes as ftm channels instead of gpios.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
- board name olimex_stm32_p405
- CPU STM32F405RGT6 Cortex M4
- LED/BUTTON support
- Console on USART2 with 8n1 115200 baud
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
ReST defines interpreted text roles where text enclosed by single quotes
can be "intrepreted", for example :ref:`some name` becomes a link to
a label anywhere in the doc set named "some name", :c:func:`funcname()`
becomes a link to the API documentation for "funcname", and
:option:`CONFIG_NAME` becomes a link to, in our case, the documentation
for the generated Kconfig option.
This patch fixes uses of `some name` (without a role) by either adding
an explicit role, or changing to ``some name``, which indicates inline
code block formatting (most likely what was intended).
This is a precursor to changing the default behavior of interpreted
text to treat `some name` as :any:`some name` (as configured in
doc/conf.py), which would attempt to create a link to any available
definition of "some name".
We may not change this default role behavior, but it becomes an option
after the fixes in this patch. In any case, this patch fixes incorrect
uses of single-quoted text (possibly introduced because GitHub's
markdown language uses single-quoted text for inline code formatting).
Jira: ZEP-2414
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This change fixes the prescaler values in the defconfig. The prescaler
values shown in the technical reference manual (STM32F407xx, p.19)
differ from those in the defconfig which results in wrong timer delays.
This patch corrects those values according to the manual. I tested it by
toggling a GPIO pin with different timer frequencies and run the
sanitycheck.
Signed-off-by: Andreas Kölbl <andreas.koelbl@st.oth-regensburg.de>
The previously used default value of 4 for the PPL_Q_DIVISOR results
in a frequency of 84MHz which is outside the acceptable range
of 47.88MHz to 48.12MHz.
The new value of 7 results in exactly 48MHz.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
This will allow checking if we are building for QEMU globally, without
having to know the exact architecture and board name.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Now that we generate BLUETOOTH_UART_ON_DEV_NAME, UART_PIPE_ON_DEV_NAME,
and BLUETOOTH_MONITOR_ON_DEV_NAME Kconfig defines for dts enabled
platforms add those into the appropriate dts files and remove from the
various board/Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch fix problems in nrf52_vbluno52 document:
+ Delete `Segger RTT` from supported features
+ Add `5.0` version to Bluetooth Low Energy feature
Signed-off-by: Nam Do <robotden@gmail.com>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Sets the default to jlink since the flashing and debugging examples
in the board document were written to use jlink.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Sets the default to daplink since the flashing and debugging examples in
the board document were written to use pyocd.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Sets the default to daplink since the flashing and debugging examples in
the board document were written to use pyocd.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Sets the default to daplink since the flashing and debugging examples in
the board document were written to use pyocd.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new variable to define which OpenSDA firmware is on the board,
and selects the default flash/debug scripts accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds the pyocd target name for the frdm_kw41z board, but does not change
the default flash/debug scripts from jlink to pyocd. pyocd has not yet
tagged a release with kw41z support, so to use it one must build pyocd
from source based on the current master branch (f21d43d).
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update the MCUX I2C driver and related platforms to get their I2C
information from the device tree. We also updated a few of the sensor
drivers found on the FRDM & Hexiwear boards to get their I2C bus name
from the device tree instead of directly from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables a usable adc driver instance based on the board design. No
additional pinmux configuration is necessary because a dedicated adc pin
is routed to the board's battery sense circuit. Updates the board
documentation to reflect that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables a usable adc driver instance based on the board design and
configures the pinmux to enable the SoC's PTB1 pin, which is routed to
the board's battery sense circuit. Updates the board documentation to
reflect that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables a usable adc driver instance based on the board design and
configures the pinmux to enable the SoC's PTB10 pin, which is routed to
the Arduino header A2 pin. Updates the board documentation to reflect
that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables a usable adc driver instance based on the board design and
configures the pinmux to enable one adc channel on the SoC's PTB2 pin,
which is routed to the Arduino header A2 pin. Updates the board
documentation to reflect that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables a usable adc driver instance based on the board design and
configures the pinmux to enable one adc channel on the SoC's PTB2 pin,
which is routed to the Arduino header A2 pin. Updates the board
documentation to reflect that the board now supports an adc driver.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
+ The VBLUno52 board
nRF52832 ARM Cortex-M4F processor
Bluetooth Low Energy 5.0
DAPLink interface
UNO pinout
4 power
+ The following samples were tested:
hello_world
basic/button
basic/blinky
bluetooth/peripheral_hr
bluetooth/beacon
Signed-off-by: Nam Do <robotden@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We can use the chosen property "zephyr,console" to determine what uart
should be used as the console and find its name to generate a define for
CONFIG_UART_CONSOLE_ON_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch add I2C to supported features and I2C section for
96b_carbon, nucleof401re and olimexino_stm32
It also adds serial port section to 96b_carbon and olimexino_stm32
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Configure I2C using DT for the following STM32 boards:
disco_l475_iot1
nucleo_f401re
96b_carbon
olimexino_stm32
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The stm32f3_disco has 40k of ram and we have some tests that require
more than that so we need to specify it in the yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
+ VBLUno51 board
nRF51822
Bluetooth Low Energy
DAPLink interface
UNO pinout
4 power
+ Wiki: https://vngiotlab.github.io/vbluno/
+ The following samples were tested:
hello_world
basic/button
basic/blinky
bluetooth/peripheral_hr
bluetooth/beacon
Signed-off-by: Nam Do <robotden@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Sidebar navigation for supported boards is wonky: opens to show
all boards (making for lots of scrolling to see the sidebar) and
sidebar items aren't always clickable (as explained in the JIRA
issue).
Fix is to not use multiple toctree directives in boards.rst and
create intermediate architecture-specific supported board docs.
JIRA: INF-132
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Board port was done before the yaml transition, so was missing a
cc2650_sensortag.yaml. As such when we build all the test we get a few
build errors that we also fixed up.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add configuration, documentation, pinmux, fixup and dts support for
STM32F103x8 based Minimum System Development board.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Allow to use an external debug adapter such as J-Link or ULINK
connected to a 20-pin JTAG header to flash the image. SWD is
the actual protocol used by the debug interface.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
As there are multiple ways to flash or debug (pyOCD or openOCD) allow
the user to override the default.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board metadata to be consumed by the sanitycheck script to provide
better matching with testcases and to test based on features declated in
the board files.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A couple of docs were created in previous PRs with board support
information common to a few boards. Move these to a new section
for "Board Support Tools". (I debated about hiding them completely
but decided it would still be useful to have these tool docs appear
in the table of contents, just not embedded with the supported boards
docs.)
Moved these board tools docs over to the doc/ folder and out of
boards/ and removed these pages from the navigation index.
JIRA: ZEP-2285
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
- board name olimex_stm32_e407
- CPU STM32F407ZGT6 Cortex M4
- LED/BUTTON support
- Console on USART1 with 8n1 115200 baud
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
The wiki directions indicate that this script should be used,
and openocd.sh doesn't even work. Switch to pyocd.sh by default.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add necessary board files, pinmux and device tree in order to have a
usable debug console.
Origin: Original
Change-Id: I43a9d278c3f2c936a714263626722f630367b663
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Following migration of stm32f1xx series clock control driver to
STM32Cube LL API, cleanup stm32 code base in order to take into
account that this is the only clock driver available for stm32
family.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following introduction of stm32cube LL based clock control driver
for stm32f1 series, update stm32f1xx based boards to support new
driver settings
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable the MPU on the Nucleo STM32F413 board.
Change-Id: I0f256a4c7231f9d3844e67a94d989c8d93b60e58
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
CONFIG_CLOCK_VDD_VOLTAGE does not exist. It was introduced by accident
with commit 614db02cc6 ("stm32f4: Add STM32F413 Nucleo board"), so
remove it!
Change-Id: I3363a92627708bf5ffb080c2238fc84c71caa8d9
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Atmel SAM3X series has been recently converted to use ASF
and should now use common SAM family drivers. The atmel_sam3
serial driver will be removed in the future.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
We now have generic ARM M4 MPU support added to Zephyr.
Let's enable it for use with Nordic nRF52 chips.
Memory Layout was generated from Section 8.3 "Memory
Map" of nRF52 Product Specifications (for both nRF52832
and nRF52840):
0x00000000: Flash
0x10000000: Factory Information Config Registers
0x10001000: User Information Config Registers
0x20000000: SRAM
0x40000000: APB Peripherals
0x50000000: AHB Peripherals
0xE0000000: ARM M4 Private Peripheral Registers
NOT Configured:
0x60000000: External RAM
0x80000000: External RAM
0xA0000000: External Device
0xC0000000: External Device
NOTE: More work will be needed for future Nordic MWU (Memory
Watching Unit) support.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Neither ASF nor CMSIS provide defines that can be processed by
the assembler. Exclude those from soc.h. Before this was done
incorrectly in board.h file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Removed CONFIG_HAS_DTS from the stm32f4_disco_defconfig &
stm32l496g_disco_defconfig files as its automatically selected for all
ARM SoCs at this point.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We now get the baud rate for the serial port from the device tree so we
don't need to be setting it in the defconfig.
The baud rate changed from 38400 to 115200 when we introduced the device
tree for MPS2. The default baud rate was based on matching mbed, but we
use 115200 to match the standard default we have for most boards now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch converts Atmel sam3x MCU series to use register
header files from Atmel Software Framework (ASF) library.
By using ASF different Atmel SAM MCU series can use common
device drivers.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Now that NXP boards support 'make flash' and 'make debug' via pyOCD and
Segger J-Link, update all the NXP board docs accordingly. Adds a new
generalized OpenSDA document so certain details don't have to be
repeated for every OpenSDA board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add configuration, pinmux, dts and documentation for the STM32L496G
Discovery board based on the STM32L496AG SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Since we now select HAS_DTS from the cortex-m Kconfig we don't need it
in 96b_carbon_nrf51_defconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds initial MPU support to NXP K6x family.
The boot configuration prevents the following security issues:
* Prevent to read at an address that is reserved in the memory map.
* Prevent to write into the boot Flash/ROM.
* Prevent from running code located in SRAM.
This driver has been tested on FRDM-K64F.
Change-Id: I907168fff0c6028f1c665f1d3c224cbeec31be32
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Link was pointing to wrong reference manual.
Fixed by this commit
Change-Id: I97c6748fcad27ad6f2541ed4cba6141fcbb2576a
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that all ARM platforms have a device tree we can move selecting of
HAS_DTS up and remove any !HAS_DTS cases, as well as setting in all the
defconfigs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add necessary board files, pinmux and device tree in order to have a
usable debug console.
Origin: Original
Change-Id: I280320700352fd36a544c03f4e57d2eeec2449e5
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Adds a new debug support script using pyOCD and configures most NXP
boards so they can use it. frdm_kw41z is the one exception because pyOCD
doesn't yet support kw41z. Tested with pyOCD v0.8.0 and the latest
DAPLink firmware for each board.
Introduces two new environment variables, PYOCD_FLASHTOOL and
PYOCD_GDBSERVER, that allow you to set custom paths to the pyOCD tools.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new debug support script using Segger JLink and configures all
NXP boards so they can use it. Tested with Segger JLink GDB server
V6.14b and OpenSDA v2.1 firmware.
Change-Id: Ia1b297d9c93d21db61379e22f27ae54cda3ad461
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Rename SOC_STM32L476XX to SOC_STM32L476XG to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file)
Change-Id: I834bb5b83c24c39e90c0492a2b22a7c7802de361
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The xC tag in the SoC reference indicates the flash size, use it in the
configuration to permit selection of correct flash size for dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds support for the nRF51 chip on the board.
If you'd like to run Zephyr on the STM32F4 chip on Carbon, you need to
use the 96b_carbon board instead.
The current SPI Bluetooth protocol only uses 5 wires, so we use the
remaining pin as UART TX.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
More general spelling fixes, and cleaning up stray UTF-8 characters
such as curly-quotes, em- and en-dashes. Use replacement strings
for |reg| and |trade|.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add configuration, dts and documentation for the Nucleo L432KC board
based on the STM32L432KC SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SimpleLink SDK actually encapsulates a family of devices,
of which cc32xx is just one device. Other devices can fit
under this SDK directory structure.
This expansion will also allow the import of the WiFi
host driver and its driver porting layer in the future,
inserted at the correct levels in the SimpleLink SDK
directory heirarchy.
Follow the URL (ending in "#directory-structure") referenced in
ext/hal/ti/simplelink/README which explains the SDK structure,
and where devices fit in.
Jira: ZEP-1958
Change-Id: I16515d3e3779de0d55d3b1b8e25029609d1f66c3
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
I2C address could not be configured for HTS221.
Remove non existing configuration in disco_l475_iot1 board
Change-Id: Ib5ed8e0f770c16b124cf918bdf9ecd42cdd9b213
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The files for the Arduino Due needed to be updated to use the new
configuration when the SoC moved from the atmel_sam3 directory to
the atmel_sam/sam3x directory.
Jira: ZEP-2067
Signed-off-by: Justin Watson <jwatson5@gmail.com>
The FPGA on the MPS2 board implements 4 SBCon devices for I2C which are
connected to:
- a touchscreen controller
- the audio device (for configuration)
- both shield connectors
Change-Id: I55ca985e18b45d68f5e7421c4768dfc9bf2fcb3f
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Introduce a simple device tree for the TI lm3s6965 SoC and QEMU
Cortex-M3 board port. We get flash and memory base addresses and sizes
from the device tree as well as the ARM NVIC number of priority bits.
Change-Id: I4452b5543de7be55518997e54837ccbfd4f121df
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As disco_l475_iot1 is default board for HTS221 sample
application, provide default boards settings to get
application functional once it is delivered.
Change-Id: Ie4957538db679d076713550c1555954a6a20d3e2
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add device tree support for nRF51822 SoCs and Arduino 101-BLE,
Curie-BLE, BLE Nano, PCA10028-DK, and Quark-SE BLE boards. This
is minimal support for memory, flash, and UART.
Change-Id: I7e572bea537e384b6d66e520462f023ace0c9b35
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree support for nRF52840 SoC and PCA10056-DK board. This
is minimal support for memory, flash, and UART.
For the nRF52840 we select between "nordic,nrf-uarte", "nordic,nrf-uart"
support for each board.
Change-Id: I1c377e0cb97ff4716ea5489fffaa7c0e2b34d18a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add device tree support for Nitrogen 96board, BLE Nano 2, and
nRF52-PCA10040 DK boards. This is minimal support for memory, flash,
and UART.
For the nRF52832 we select between "nordic,nrf-uarte", "nordic,nrf-uart"
support for each board.
Change-Id: Ia247b9b710a72416e9ab0de3ca1429bfab8917f8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit provides support for disco_l475_iot1 board
Pinmux driver is provided with initial support definitions
Change-Id: I17b637a8ba0b033014969eca8fffe76319c47c52
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In order to allow the use of such board, a very preliminar port was
developed. It consists of board files, as well as pinmux, uart, gpio,
spi drivers and device tree files.
Change-Id: I5753064e39e0b023cf4481744c176de26d8dbebb
Signed-off-by: Gustavo Denardin <gustavo.denardin@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commits align CONFIG_ factor names between stm32f4 and stm32l4
series to enable code factorization such as use of Q_DIVISOR.
Though, it does not concatenate kconfig sections as we might use
a bit of time to see what is needed in this regard
Change-Id: Ia603406d53949abf5675b801a5448397d5ab8462
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following activation of stm32 common clock driver for stm32f4 series
remove references to stm32f4 specific driver.
Change-Id: I372a0ea046007bcb34944d6b2b8880077583b1d3
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit provides CONFIG_ definitions to support
LL based clock driver on stm32f4 boards:
96b_carbon
nucleo_f401re
nucleo_f411re
This commit sticks to clock configurations previously defined.
Two changes to notice:
-HSE clock value should now be defined
-Prescaler values required as "1" should now be set to "1" instead
of "0".
Change-Id: I003bd226f198217d5e266e11fe37094773c1c62c
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added some review changes suggested by TI-er Bill Mills.
Jira: ZEP-1958
Change-Id: I892f22a5740ae7ae4dc949bc72de366e0e85d03c
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
This board is being replaced by the CC3220SF LaunchXL,
which has essentially the same peripheral map, 256Kb
of SRAM, but in addition has 1Mb of on-chip secure flash.
Jira: ZEP-1958
Change-Id: I80629474cab9ce41bce3903213f5c9f148cc138a
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
CC3220SF_LAUNCHXL effectively replaces the CC3200_LAUNCHXL,
with support for the CC3220SF SoC, which is an update for
the CC3200 SoC.
This is supported by the Texas Instruments CC3220 SDK.
Jira: ZEP-1958
Change-Id: I2484d3ee87b7f909c783597d95128f2b45db36f2
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Typo in :ref:`hello_world` (regular quote vs. back tick)
Change-Id: I77853f85b9c71751307ef105b6babcb0cfbc9060
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This patch adds MPU support to the ST nucleo_f411re board based on
STM32F401XE.
Change-Id: I43aae0930ccabe234fcb34216518b568a855a1be
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds MPU support to the ST nucleo_f401re board based on
STM32F401XE.
Change-Id: I5e8042c1f964827980b974a565a4d4666eeccf3b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds MPU support to the 96 boards Carbon board based on
STM32F401XE.
Change-Id: I8444318099a665133488ccdd5ba129c805f9a20e
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch enables MPU by default into the V2M Beetle port of Zephyr.
Change-Id: Iab2dea748c68a6932eb31e746d1a9cdb07808683
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The current PLL settings for the Carbon have two problems.
1. The VCO frequency (672MHz) is out of spec.
2. The 48MHz clock is being driven at 84MHz which breaks USB,
breaks SDIO and also risks biasing the RNG.
Fix this by bringing the VCO down to 336MHz (which also fixes
the 48MHz clock) and update the other dividers accordingly.
Change-Id: I394c476a8b27f027da5cdc31992613b376cf6aff
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I27d51c316144251939b20cfa6787ff7ab8035fe6
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix doxygen comment typos used to generate API docs
Change-Id: I248d53000d8e57b902b9a18fdcfc9e995142a8b3
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Added serial (UART) driver for Atmel SAM MCU family.
Note:
- Error handling is not implemented
- The driver works only in polling mode, interrupt mode is
not implemented.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1959
Change-Id: I3e770fd1feb2ddf92cf405a9aa17be92eb32e19b
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added I2C bus (TWIHS) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1866
Change-Id: Ic5aa7b6b21295feccae883d580b38bbeaf2ce291
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
CONFIG_BOARD was set to arduino_101_ble instead of curie_ble. Fix this
so the BOARD_NAME, BOARD, board dir, all are in sync.
Change-Id: I5f2a4f1aeec7c20f042e11b96e1c87883ad4df4b
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce SoC specific config options similar to what exists on NRF51,
this is mostly to help distinguish between SRAM & Flash sizes on
different variants.
Also deleted some unnecessary setting of CONFIG_SOC_NRF528{32,40} in the
board defconfig files.
Change-Id: I3aaedf0c15423ae12636f87b8e6a39070cbb2c6f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds initial support and documentation for the kw40z on the hexiwear
board.
Jira: ZEP-1391
Change-Id: Idb58bfb3c2951b1f737a8c547860bde4ef4d9a3e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converted over all STM32F3 based boards to use device tree and removed
associated bits that now come from the device tree for STM32F3.
Boards that are now using devicetree:
* Nucleo f334r8
* STM32373C Eval
Change-Id: I081a1d83f86e417a98b6864c745354b6b32953b7
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Converted over all STM32F1 based boards to use device tree and removed
associated bits that now come from the device tree for STM32F1. Also
renamed the STM32F10{3,7} SoC dtsi to try and make it clear that the 'X'
is a place holder. Fixedup the top level compatiables in the boards to
be the specific 'X' instead of the generic one.
Boards that are now using devicetree:
* Nucleo f103rb
* STM3210C Eval
* STM32 MINI A15
Change-Id: I29b3634ec7451f974687d55980414efa655e2e96
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Converted over all STM32F4 based boards to use device tree and removed
associated bits that now come from the device tree for STM32F4.
Boards that are now using devicetree:
* 96b_carbon
* nucleo f401re
* nucleo f411re
Change-Id: Ibe197ca0a3f5ad78d594485a578d986403cc824a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since all the L4 SoCs are using DTS we can remove the various Kconfig
bits that we now get from DTS.
Change-Id: Icdec49b478ff285dc3347b09412964a721f75bbf
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
By default a factory new SAM E70 chip will boot SAM-BA boot loader located in
the ROM, not the flashed image. This is determined by the value of GPNVM1
(General-Purpose NVM bit 1). Updated flash procedure will ensure that GPNVM1
is set to 1 changing the default behavior to boot from Flash.
Change-Id: Ic6334c9d4743a7665fc944e8f49fc1467ecda40d
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add openocd.cfg to control flashing and debugging of the
olimexino-stm32 board
Change-Id: Ia40d964b737792864efd85076bc599b2de15ebb0
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The schematics of the BBC micro:bit are hard to find, and its official
web-site doesn't document the mapping of the edge connector pins
numbers the nRF51 GPIO pin numbers. Provide helpful defines for this
in the board.h file.
Change-Id: I52ce1d61558703b6aa5a5d073ccd222f27fa8760
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
update references to shell sample that was moved by
https://gerrit.zephyrproject.org/r/#/c/12442/
Change-Id: I61b527c9077b05b67fc9c43f2ecff50dc92dae9c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Adds fxas21002 and max30101 sensors to the list of supported features in
the hexiwear_k64 board document. Updates the pinmux table with the
sensor pins and sorts it by port name, then pin number.
Change-Id: I7d4c2c3b7b0e6e52b34e5675ce957c3bc5d18d46
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
These are fixed I/O registers for getting and setting the states of
LEDs, buttons, SPI chip-selects, and LCD control lines. It also contains
several free-running counters with no specific use.
Change-Id: Ib49306d5501574f7eb354165cdca6f29e3d4dad4
Signed-off-by: Jon Medhurst <tixy@linaro.org>
On stm32 family, IP instance numbering starts from 1.
Update i2c driver to this scheme to minimize user
confusion
Change-Id: I967d5975bbbad59cd8a3a7b6dfc665955d09cc9f
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
For the SoCs in which all the boards for that platform are using dts we
can remove the Kconfig bits that are now coming from device tree.
Change-Id: Iccf4c84beb83fa1c516b6166f94de37b4a0162ae
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Previously, cc3200_launchxl board was not able to show the
Zephyr Boot Banner, as that required early initialization
of the UART driver, which was done POST_KERNEL.
This patch moves the pinmux and UART driver initialization
to PRE_KERNEL_1, allowing early printk, and the Boot Banner
to show.
Change-Id: I84a7c20c1d5bdc3de150dc6bb0adebc9a2d9f5cb
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The LEDs on BBC micro:bit boards are red and not green. Since
mentioning the color doesn't really provide any value to the GPIO pin
definitions, just remove it.
Change-Id: I7f53e0d8a0733cda911a624d0b53c750eacfa685
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds the necessary changes to enable use of DTS for
generating required build information.
Change-Id: I0d7aa15488339a425ffe57b6354992851212f7f3
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Now that dfu-util is a supported flashing method, make it the
default flashing option for Carbon when used via 'make flash'.
Change-Id: I0d2fb9a8cbb4324ea77f1c94ca5df6f1a51e67f6
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Tested on nrf52_pca10040 and nrf51_pca10028 using hello_world sample.
Change-Id: I7cdf1d21e7f8232da737a06e5afbfb1eaec05cde
Signed-off-by: Michał Kruszewski <mkru1992@gmail.com>
Let 'make flash' invoke the dfuutil.sh support script, and
export the relevant DFUUTIL_* environment variables, for all
3 cores of the Arduino 101 board: x86, ARC and BLE.
This is backward compatible with the current usage of OpenOCD
over JTAG, since this is only enabled when the environment
variable ZEPHYR_FLASH_OVER_DFU is set to y.
Change-Id: Ic5528cb87a180378d7120d150c27d1e24c9ebe75
Signed-off-by: Patrice Buriez <patrice.buriez@intel.com>
Basic Watchdog driver for Atmel SAM family MCUs. Currently only
disabling the watchdog is supported.
Tested on Atmel SAMV71 Xplained Ultra Evaluation Kit.
Origin: Original
Jira: ZEP-1684
Change-Id: I8f717c7f53aa290c944b7935e0570c2a6f53956e
Signed-off-by: Souvik K Chakravarty <souvik.k.chakravarty@intel.com>
Provide BUT button and LED1, LED2 leds defines in order to get
basic samples "blinky" and "button" available on olimexino_stm32.
Defines have been named in order to match with board printing.
Aliases are provided to get compatibility with zephyr sample code.
Change-Id: I975dc6c043ea83935fb229cafc737cb3ed80fdc4
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This patch automates flashing process for arduino_due board. Just make flash will able
to flash binary file on the board.
Bossa tool(http://www.shumatech.com/web/products/bossa) manual flashing process is
automated through shell script and currently this binary is only available for
x86_64 architecture.
JIRA : ZEP-145
Change-Id: Ib7b525466239d0437e449c56827f8a9b3e5a96a1
Signed-off-by: Punit Vara <punit.vara@intel.com>
This includes:
* Moving the Nordic nRF5x Segger J-Link page (temporarily placed inside
one of the board folders)
* Moving the nrf52_pca10040 doc
* Moving the nrf51_pca10028 doc
* Moving the nrf52840_pca10056 doc
Change-Id: I051eb51cee8166ae6472eb696ffeb0625a0424c7
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add basic PHY management sufficient to detect link up, link down and
auto negotiated link speed / duplex. The PHY driver is implemented as
a state machine that executed in the system work queue. The
implementation is non blocking, using the MII interrupt to capture the
completion of read and write events.
This PHY management should be fairly generic. In the future, it may be
beneficial to pull this code out as a standalone PHY driver for use
with other ethernet drivers.
JIRA: ZEP-1674
Change-Id: I3dcb5c14982ef4b40591fcf10d84840b8a2558e5
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
After introduction and activation of STM32Cube LL based driver on
F3 and L4 series, this commit removes the no more needed code for
native driver for these soc.
Change-Id: I266d1a3fc4b464cee34b1cc1a1a333c5bf923e41
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Activate support of LL Cube based Clock control driver
Note that prescaler should now use actual numerical value used
for calculation and not register value (hence 1 instead of 0)
Change-Id: Ia3a26bffbd470c6e958fd2ca82b8eb071beb6ca8
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Activate support of LL Cube based Clock control driver
Note that prescaler should now use actual numerical value used
for calculation and not register value (hence 1 instead of 0)
Change-Id: Ic2566d26f1b82441575a94ddd8d632c88df669d9
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Activate support of LL Cube based Clock control driver
Note that prescaler should now use actual numerical value used
for calculation and not register value (hence 1 instead of 0)
Change-Id: I4becae974678970745f918fb05906f36cc4d62a7
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds the base DTS support for the KW41Z Freedom board. The
initial set of changes include SRAM, FLASH, IRQ controller and LPUART
support.
Change-Id: Ic68c4959ddad0c5cfe70d5576a0e58372b93ec9d
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
This patch adds the base DTS support for the V2M Beetle board. The
initial set of changes include SRAM, FLASH, and IRQ controller support.
Change-Id: I06685622b9c57ac358544c71350074ce06e3371e
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds all the necessary changes to enable use of DTS for
generating required build information.
Change-Id: Ia476fbb14c7d9d6b9db3340c73f599556a880da3
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch ifdef's out information that would be redefined by
information generated from DTS. This patch also fixes up the serial
drives to work properly with the DTS generated information.
Change-Id: I912ccf35be23c107705a4866e5a68b3b51154ffa
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds DTS support for the Hexiwear K64 platform. This
includes enabling the DTS config option and adding conditionals around
the options to be replaced.
In addition, a DTS file is provided that customizes the Kinetis
platform to match the hexiwear board. A fixup file is provided to map
the generated information to the current client driver usage. This
file is temporary.
Change-Id: I247d538c6e13e0d1d4141fee74046575a7d2972e
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds DTS support for the FRDM_K64F board. The defconfig
enables the DTS usage and the FRDM K64F specific DTS file provides the
differences from the base Kinetis DTS definitions.
A fixup file is provided to map the generated configuration information
to the driver consumers. The fixup file will be removed once the
drivers are modified to handle the newly generated information.
Change-Id: Ib0ada28faff6a30e8b40eba5c5853e9018ae5fcb
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds DTS support and related files for the NXP Kinetis
platform. The DTS files contain the base definitions for the hardware
nodes on Kinetis platforms. The YAML files provide the definitions of
the contents of the DTS nodes.
The Kconfig changes were put in place to allow for the conversion of
existing drivers. Once those drivers are modified, the Kconfig options
that are replaced by the DTS information will be removed.
Change-Id: If110fffa99c0b12471cf2df206da6687277e4756
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This commit changes Kconfig prefix for ieee802154 drivers to
IEEE802154_*. This is done for consistency with config prefixes
used in other subsystems.
Change-Id: Ibbb4d96d2b748f4f13135bde85304ec34c5a90a6
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
Working Ethernet, and actually even successfully booting with Ethernet
enabled (and Ethernet is enabled by default on enabling networking)
so far requires a network cable attached.
Change-Id: I9c17e417f867942ddf085db9e8342e945aa07370
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
These two docs have a long skinny list of items that displays
better as a multi-column list (using the hlist directive).
Change-Id: Ia1a1f8555bdefe0c9051944d9946299395258bfc
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Origin: Original
Jira: ZEP-979
Change-Id: I1af64364b5b3b4aadbee225ee8f89615fa292863
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
Following comments on nucleo_f411re doc, update doc for
nucleof401re
Change-Id: I86b7a016b604a31e210e425718e835e15560a46a
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch updates the mps2_an385 documentation adding the information
of the CMSDK (Cortex-M System Design Kit) GPIOs Pinmuxing.
Change-Id: Icab0d47bf1a58be058f036fb3db346ef6390266a
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch updates the mps2_an385 documentation adding the information
of the new added CMSDK (Cortex-M System Design Kit) Drivers.
Change-Id: I5615ebec13e8831a0360fc32cfd8be0d3ebc85b5
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch enables the CMSDK (Cortex-M System Design Kit) Drivers on
mps2_an385 (Cortex M3).
Change-Id: Iff51141a183ac94ad6b905acf10389ca94a451d3
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Adds initial support and documentation for the frdm_kw41z board.
- Configures the kw41 to use the 32 MHz external oscillator on the board
to generate a 40 MHz system clock. The clock settings match the MCUX
SDK hello_world example project.
- Provides pinmux settings for the uart, i2c, LEDs, and switches
- Enables pinmux, gpio, uart, and i2c driver instances
- Configures the fxos8700 accelerometer/magnetometer driver
Jira: ZEP-1390
Change-Id: I025a0eae3d380eaf90b02683acf5c592e2204a2e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
ARM's Cortex-M Prototyping System (MPS2) is a board with an FPGA that
can be programmed with different 'SoCs'. To use these in Zephyr we need
a set of board files for each variant.
This adds a board for a variant which implements a Cortex-M3 CPU; the
naming of this matches that used for the Zephyr SoC (which is itself
based on ARM's documentation nomenclature).
Change-Id: Ie02a67a03016b8aeee31e3694f0edbcc37f9ee64
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add the GPIO pin and port definitions for the LEDs available on the
board.
Change-Id: I586a0ebfbbe8fa6e50dd1f91c1437665dd8ec677
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Add the GPIO pin and port definitions for the button and LEDs available
on the board.
Change-Id: If74cf9d780227346c7c8816e6eadca00b16953b2
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
This patch updates the default defconfig in order to support the new
Timers implementation.
Jira: ZEP-1300
Change-Id: I749042bcf41c6b4cb11614315c3c2ce09cdb2aa8
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Since commit "build: use target 'debugserver' for Qemu debugging",
DEBUG_SCRIPT should be used to enable make debug option
This commit provide debug option to following boards:
nucleo_f334r8
nucleo_f401re
stm3210c_eval
stm32373c_eval
Change-Id: I92eb36257b6e05125440b0e83985d59bcda27aa8
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Stop using the specific uart_k20 driver by default and start using the
more generic mcux uart driver instead.
Jira: ZEP-719
Change-Id: I7b107ea7118887591362159283ebb5413b45595a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This follows the board.rst template in the RFC
for board documentation:
https://gerrit.zephyrproject.org/r/#/c/9703/
This RST file was validated visually by rendering
using the online tool: http://rst.ninjs.org/
JIRA: ZEP-1541
Change-Id: Ibe6e1c7f8eb3c7862b4087a78b469693927280a2
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The headings on some .rst files were not following the expected
heading order of using # for h1, * for h2, = for h3, and - for h4
This patch fixes that, and the doc/templates/*.tmpl files created
for folks to use as templates for creating board and sample docs.
Change-Id: I0263b005648558d5ea41a681ceaa4798c9594dd9
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The k64 gpio driver quietly initializes the pinmux to force the pin to
be a gpio, regardless of the setting defined by the board's pinmux
table, or even if the pin was not in the pinmux table.
This behavior caused the accelerometer interrupt pin to be incorrectly
defined in the frdm_k64f and hexiwear_k64 pinmux tables.
Change-Id: If46df0e051452fef291d5ad5cdff56463d5f465e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hexiwear_k64 i2c pinmux settings were copied over incorrectly when
the new mcux pinmux driver was created.
Change-Id: I72e5f8f7c06e2d9b08921109691edaf311f3811b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moves the uart console pins from the k64 soc init to the frdm_k64f and
hexiwear_k64 board pinmux tables. Not having these pins in the board
pinmux tables led one to believe that no pins in PORTB were being used
on the hexiwear_k64 board, and thus the port was incorrectly disabled by
default.
Also fixes PORTB to be enabled by default if the uart console is used.
Change-Id: Ide6b7b34dfba8a75a02a8f2bf37cce843afb92f1
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Provide USER button and LD2 Led defines in order to get basic samples
"blinky" and "button" available on nucleo boards.
Defines have been named in order to match with board printing.
Aliases are provided to get compatibility with zephyr sample code.
Change-Id: Ie23a4f63c406def50b94a644d4e136d3bda1ceff
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Previously, CC3200 drivers had two options to use the peripheral
driver library APIs:
1) Build driverlib SDK files in Zephyr, in ext/hal/ti/cc3200/*
2) Link directly with the driverlib.a, from an externally installed
TI CC3200 SDK.
A new option is added to replace option 2), and is now the default:
3) Use the driverlib functions already provided in ROM.
This enables a savings in code size, which will depend on the
types of device drivers configured and the number of SDK
APIs actually used.
A rom_report build of the shell sample application showed
a savings of about 2kb in code space using this new config option.
Change-Id: Ie1ede6f7aacd23db20f5292e776f1dfeab5c7fe0
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Merges the ksdk pinmux dev driver into the regular ksdk pinmux driver,
which now exposes the public pinmux API. Removes the private ksdk pinmux
API and converts the frdm_k64f and hexiwear_k64 boards to use the public
pinmux API.
Jira: ZEP-958, ZEP-1432
Change-Id: Ie5f60b604133093050b9c596050cad776d7b7cb3
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enable PORTD on the frdm_k64f only if SPI_0 is enabled. Otherwise, there
are no pins in the pinmux table for this port and it should be left
disabled.
Change-Id: I7f8a05552f6a320debfd11a780be1092da831101
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Disable PORTA and PORTB by default on the hexiwear_k64 since there are
no pins in the pinmux table for these ports. Enable PORTE only if UART4
is enabled.
Change-Id: Ifdb01cacf0c475a9478454eb61474a930e22a628
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds the documentation page for the ARM V2M Beetle board into
the Zephyr tree.
Jira: ZEP-1300
Change-Id: I4f2fd9a4e496c0a674272f94bedcadf3c71d9971
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
We get odd warnings associated with Kconfig because of this:
warning: symbol value '0# empty for now, use this file for global kernel
configurations and overrides.' invalid for CLOCK_STM32F4X_APB2_PRESCALER
Change-Id: I77c2828ab29dfa179f345953cc490dbd67fd0b5a
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This will replace the current goal of 'make qemu' with 'make run' and
moves Qemu handling into its own file and into the boards instead of
being architecture specific.
We should be able to add new boards that support some other type of
emulation (by adding scripts/Makefile.<emu type>) and allow the board to
define their own options for the use type of emulation.
'make qemu' will still work, however it will be deprecated, starting
with this commit it is recommended to use 'make run'.
Jira: ZEP-359
Change-Id: I1cacd56b4ec09421a58cf5d010e22e9035214df6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use the existing debugserver target also for Qemu debugging. Qemu
should be maintained as one of many emulation/simulations platforms and
emulation should be abstracted in the Makefiles and not tied to Qemu.
qemugdb will still work, it is however being deprecated.
Change-Id: I0cd10fb66debb939b8f7f1304bf2ef4605da6a1d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The basic button sample expects SW0_GPIO_NAME and SW0_GPIO_PIN macros to
be defined by board.h. The frdm_64f doesn't have a physical switch with
this name, so create an alias to SW3 to make the sample work.
Change-Id: I61eb096582d9898dbcb9799e69078ad0c4b700cf
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The basic blinky sample expects LED0_GPIO_PORT and LED0_GPIO_PIN macros
to be defined by board.h. The frdm_k64f and hexiwear_k64 boards don't
have a physical LED with this name, so create an alias to the green LED
to make the sample work.
Change-Id: I3426c571bb2e3165dbd9f4372d863b474c35fd5c
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Previously, UART clock enable was done in pinmux init.
This is now moved into soc initialization, along with other
power related initialization routines.
Change-Id: I1f9464655ad966e9caac2d238006f12a06b202ab
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Previously, running UART applications in Zephyr from sFlash would
not show consistent character output.
The PRCM clock enable for UART was missing the sleep mode while
enabling the UART clock.
This has been fixed, and verified with philosophers (polled output)
and shell (interrupt driven) zephyr examples running from sFlash.
Change-Id: I95a87996f252d82b0c1c13d3f77535971b5cf9c5
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
For the basic samples to work, button and LED definitions are required
in board.h. These map the buttons and LEDs present on the board to
the corresponding GPIOs they are wired into.
In this particular case the LEDs are actually arranged in a 3x9 matrix,
with the GPIOs wired to the rows and columns of said matrix. An upcoming
patch will provide utility functions to access the matrix.
Change-Id: Icce93ee6a08ae28445c6dc4a41529105ac80f14a
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
For the basic samples to work, button and LED definitions are required
in board.h. These map the buttons and LEDs present on the board to
the corresponding GPIOs they are wired into.
Change-Id: Ia0be30cecd8c0ceabb495258480eb6f3ce13d3e5
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
For the basic samples to work, button and LED definitions are required
in board.h. These map the buttons and LEDs present on the board to
the corresponding GPIOs they are wired into.
Change-Id: I2785441c286b95fd77e636e9bf3d68bc9f5a1acc
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
For the basic samples to work, button and LED definitions are required
in board.h. These map the buttons and LEDs present on the board to the
corresponding GPIOs they are wired into.
Change-Id: I60903eb834ef1b2618b0525896c120fca84db177
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To make way for the upcoming blinky and GPIO support for nRF5x-based
boards, this change addresses the hardcoded dependencies in Kconfig
default configurations of the different boards, moving the common option
defaults to the SoC default configuration itself.
Change-Id: I8db0750311ad5a12b76237b39438376f20f6f496
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds generic definitions for GPIO pins for onboard LEDs and
switches to enable the basic blinky, button, and disco
Zephyr examples for the TI CC3200 LaunchXL.
Change-Id: Iac0ed2ad01285f9e84eea1fa7013771ddd8d3a78
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Leverages the configuration generated by the TI recommended PinMux
utility to enable pins for the 4 GPIO ports on the CC32xx LaunchXL
board, pre-configuring GPIOs for the onboard:
- 3 LEDs, and
- Two user push buttons (SW2, SW3).
The pinmux configuration is used in lieu of a Zephyr
pinmux driver, and is called during board initialization.
Change-Id: Id2403fc2ec3fcc0a62ee5149e1ac596e7e06ead4
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
With the appearance of the nRF52840 IC a new Preview Development Kit
(PDK) board has been introduced. This patch adds basic support for this
new board.
JIRA: ZEP-1418
Change-Id: If5845e75312ec756b968e595e5dc31c4c9624be2
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In preparation for the new Nordic MDK and nRF52840 IC support this patch
adds the specific nRF52832 IC model in the pca10040 board default
config, so that future boards with different ICs from the same nRF52
series are supported correctly.
JIRA: ZEP-1418
Change-Id: Ic7c2076eeeb33fb729e4dbba2ff4702ab812a826
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
All pins from the existing pin init in
drivers/pinmux/k64/pinmux_board_hexiwear_k64.c were brought forward.
Jira: ZEP-1393
Change-Id: I3eb38dc435809cb7997d5884ff63bf8dd1e54720
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Some pins were not brought forward from the existing pin init in
drivers/pinmux/k64/pinmux_board_frdm_64f.c because they do not appear to
be used anywhere and it increases power consumption to enable them. For
example, 6 pins were enabled as analog inputs, but there is not yet an
ADC driver for the k64. The pins that were not brought forward are:
* PTA 0-2
* PTB 2,3,9-11,23
* PTC 2-4,10,11
Jira: ZEP-1393
Change-Id: I7410f6d993bd0a4df8f80df72e84def73bcf74cc
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch updates defconfig file on V2M Beetle board in order to enable
clock_control and watchdog by default.
It defines also a dummy LED in order to maintain compliance with the
Zephyr test environment.
Jira: ZEP-1300
Change-Id: I40ae4cb19e79ff24e1e351a2185a7191f03664d1
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add board support for the Nucleo64 L476RG development board.
Change-Id: Ibb5424bc936c67a5d96855617202136d7dea772c
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
There was a misalignment between Zephyr UART device numbering and
SoC UART IP. Device "UART_1" was mapped to IP USART_2, which could
be confusing for user.
This commit allows to align "UART_1" to IP USART_1.
Change is propagated to all STM32F103RB/STM32F401RE based boards and
respective pinmux drivers
Change-Id: Ia8099dfeec7b9c0c686c2a58ccb4dbb1a55b6537
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add defaults for the fxos8700 sensor, including which i2c instance, the
slave address, and interrupt pin.
Change-Id: Ib8a1e451ddfd84d2b2f19b0da846854acc969dcf
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add defaults for the fxos8700 sensor, including which i2c instance, the
slave address, and interrupt pin.
Change-Id: I4b0255308fd5c9b7c43f0f22e8ce2fe86c5e7011
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Make the blinky application work with this board.
Change-Id: Ibe8d310229e2ff79a2164b7c8f16e7ba3ee0b8c2
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add board support for ARM V2M Beetle platform.
ARM V2M Beetle board is build around the ARM Beetle Cortex-M3
based processor.
The support has been tested in nanokernel mode with the bringup
application that will be pushed with a future patch.
Jira: ZEP-1245
Change-Id: Ib05a40c072f10149e692283177387cf2cfe32f66
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The Quark SE C1000 BLE Core is a nRF51822-QFAA, with 16kB of RAM and
256kB of flash. The configuration is otherwise similar to the Arduino
101 BLE, except that the UART RTS pin is the same as that used by
nrf51_pca10028.
Change-Id: I88cb18876bdde65abcf9a499894f70802046c824
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Board uses nRF51822-QFAA, with 16kB of RAM and 256kB of flash.
The UART has no hardware flow control pins.
Change-Id: I16ffeee15a1f5714c695dc8b38e77fb134ea7a0f
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Change the default Bluetooth UART device name to the UART connected to
the arduino header. This allows using the frdm_k64f with a frdm_kw40z
shield board.
Change-Id: Id22950f0a48a7c95bcddc6f1ec044f7a37cb9b72
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Change the default Bluetooth UART device name to the UART connected to
the on-board kw40.
Change-Id: I2ae981bce31a58aed4dc6d3c378fc6f6a0bec76f
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/hello_world
- samples/philosophers
- samples/drivers/uart
- samples/shell
UARTA0 is currently supported.
Change-Id: I85727c622d4d42183cc9f2f8b43d653e245dd17e
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Leverages the pinmux.c file generated by the TI PinMux utility
to enable UART pins. The pinmux configuration is used in lieu of a Zephyr
pinmux driver, and is called during board initialization.
UARTA0 is currently supported.
Jira: ZEP-1109
Change-Id: Iddb01f79043af034886859b608b7b6aadf844e53
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Added Kconfig and makefiles to be able to build a Zephyr application
on Linux/gcc, and load via OpenOCD.
Validated by running the hello world, and philosophers microkernel
samples, and stepping through the code in gdb.
Jira: ZEP-1109
Change-Id: If5d3e7b1a8ecf5ecf6a00f147742b3bc5716190f
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The k64 SoC has multiple instances of many peripherals, but which
instances can actually be used depends upon the board design and pinmux
configuration.
Move all instance-specific default driver configurations from the SoC to
the boards (frdm_k64f and hexiwear_k64). Default driver selection
remains in the SoC (e.g., enable the KSDK I2C driver when I2C is
enabled).
This paves the way to support different driver defaults for the
frdm_k64f and hexiwear_k64 boards, but it does not yet change any of the
default values; it only changes where the default values get set.
Change-Id: Id9ed898762eb400ecefeac91ae4dce66da05622d
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
STM32Cube uses SoC defines made to reflect HW heterogeneity that
should be taken into account by SW.
Aim of this commit is to adapt values used by Zephyr to the same
diversity. This will help create new SoC values only when justified
by a real hardware difference that should be taken into account
by software.
For instance, for SoC stm32f401re following define is used:
*STM32F401xE
Which means:
*Same SW could be used on STM32F401RE and STM32F401CE:
same CONFIG_SOC could be used
*Different SW should be used on STMF401RE and STM32F401RC:
different CONFIG_SOC should be used
This change focuses on stm32f4xx series.
Change-Id: I56ff4d1815d09747cf722385532eb2dcbdf37b44
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32Cube uses SoC defines made to reflect HW heterogeneity
that should be taken into account by SW.
Aim of this commit is to adapt values used by Zephyr to the same
diversity. This will help create new SoC values only when justified
by a real hardware difference that should be taken into account
by software.
For instance, for SoC stm32f103rb following define is used:
*STM32F103xB
Which means:
*Same SW could be used on STM32F103RB and STM32F103VB:
same CONFIG_SOC could be used
*Different SW should be used on STMF103RB and STM32F103R4:
different CONFIG_SOC should be used
This change focuses on stm32f1xx series.
Change-Id: I5ecfaa52952d04421b27b5e74fb71b4fc108b662
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Board uses nRF51822-QFAA, with 16kB of RAM and 256kB of flash.
Change-Id: I92b543022ae6103683cc9e16b925508fb3cf7db1
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Move common config options one level up to try to simplify the per-board
defconfig
Change-Id: I3d80fa494050634d0f877af2015b01b85df20d1d
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for the STM32F401 chip on the board
Change-Id: I96c0799f3658ecea096fa5971bce9faf21919ee1
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The BLE core on the Arduino 101 is an nRF51822 QFAA (256kB flash, 16kB
RAM).
Change-Id: Ia802b3eb634c0cd6775c4059c9569bccd915a578
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Removing options that are already set by the soc Kconfig files.
Change-Id: I603c7797a26e3afedfa5ee72fe989c614c080fe5
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Introduce an architecture sorting of boards. This is to allow for
easier maintenance going forward as the number of boards grows. It
will be easier for any scripts to know the board/arch mapping without
having to maintain an explicit list of what boards are associated with
which arch. We can also do things like have architecture maintainers
cover reviews and branches for arch/${ARCH} and boards/${ARCH} going
forward.
Change-Id: I02e0a30292b31fad58fb5dfab2682ad1c5a7d5a7
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>