After introducing STM32Cube based clock control driver for
stm32 family, update stm32 i2c_lx driver to support it.
Clean up will be done in a following commit.
Change-Id: Ie5059bf4122d65fab1a663a5b00e0d761850a49d
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use of SECONDARY in DEVICE_AND_API_INIT is now deprecated and should
be replaced by POST_KERNEL
Change-Id: I543ae70e493527e75b4a4bcb9191475065b49166
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update stm32 serial driver to support it.
Once supported across the whole family, a clean up will be done.
Change-Id: I7100bc699e7918c8be71d58091da1860ab734e25
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update pinmux driver to support it.
Once supported across the whole family, a clean up will be done.
Change-Id: Icc20816377f3a09f516a743462c92696a1fead3a
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update GPIO driver to support it.
Once supported across the whole family, we clean up will be done.
Change-Id: If50cb580cb01dc1d38557e54f19a8260feaa504e
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This new clock control driver aims at providing a lightweight
generic driver to the whole stm32 family.
Driver is based on LL Cube API and hence is for now available
only for STM32 supporting this API: stm32f3xx and stm32l4xx.
Other families should be supported soon.
Once globally supported, this unique driver will also help
reducing the impact of stm32 clock control heterogeneity in
other drivers.
Change-Id: Id15a8d0d44f03809b2907ef10d6877700459e674
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds the base DTS support for the KW41Z Freedom board. The
initial set of changes include SRAM, FLASH, IRQ controller and LPUART
support.
Change-Id: Ic68c4959ddad0c5cfe70d5576a0e58372b93ec9d
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
This patch adds DTS support to the ARM CMSDK UART driver. The DTS
currently specifies the IRQ, IRQ PRIO, and base address of the port.
Change-Id: I8e5bc81c013958be4297d563495bf126b53a83a9
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds device tree support to the STM32 UART driver. The base
address, interrupt, and interrupt priority values can now come from DTS.
Change-Id: I3c383da8b200037601ecb2dc087f99ef103761bb
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch ifdef's out information that would be redefined by
information generated from DTS. This patch also fixes up the serial
drives to work properly with the DTS generated information.
Change-Id: I912ccf35be23c107705a4866e5a68b3b51154ffa
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds DTS support and related files for the NXP Kinetis
platform. The DTS files contain the base definitions for the hardware
nodes on Kinetis platforms. The YAML files provide the definitions of
the contents of the DTS nodes.
The Kconfig changes were put in place to allow for the conversion of
existing drivers. Once those drivers are modified, the Kconfig options
that are replaced by the DTS information will be removed.
Change-Id: If110fffa99c0b12471cf2df206da6687277e4756
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This commit removes unnecessary CONFIG_SYS_POWER_DEEP_SLEEP protection
in shim drivers as QMSI 1.4 has introduced empty context save/restore
functions that can be called in Quark D2000, therefore keeping common
code at the shim driver level for Quark SE and D2000.
Change-Id: Ia2a466327f999668c6511c0193014e9151bff6ae
Signed-off-by: Juan Solano <juanx.solano.menacho@intel.com>
Use new device name for SPI device
Jira: ZEP-1704
Change-Id: Iec39468bbef54423af2b3a681dd4ae1eee866d1e
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update the qmsi dma shim driver based on the new dma api
interface.
Recently, a RFC was posted to update the dma api. The update
to dma api interface was already posted. This change is to
update the dma qmsi shim driver based on the dma api change.
It is using the new data structures and new api function names.
Jira: ZEP-873
Change-Id: If9a772c5ff1c2b10fca05172c48f75223bbf940e
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Enabling the riscv_machine_timer driver by default for riscv32
causes compilation issues on riscv32 boards (like zedboard_pulpino)
not supporting it.
Boards supporting the driver enable it via their respective
config file.
Change-Id: Ieb0d25fa339834fd386ae2725f40b6b7b72dc52b
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
This is one the series patches that simplifies the driver code by
using the IS_ENABLED macro. This removes the need of the const
variable and the wrapper functions on semaphore APIs.
Jira: ZEP-1251
Change-Id: Ic2df5d04966d2a066478ca3e119f76d24fc4dfb3
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
This is one of the series of patches that simplifies the driver
code by using the IS_ENABLED macro. This removes the need of the
const variable and the wrapper functions on semaphore APIs.
Jira: ZEP-1251
Change-Id: I84a09a0aaa3a00452d8c2b4bca7be0f6b2015218
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
This is one the series patches that simplifies the driver code by
using the IS_ENABLED macro. This removes the need of the const
variable and the wrapper functions on semaphore APIs.
Jira: ZEP-1251
Change-Id: I59802cf9f482337656b0fdc4b272f3b1ddc6cbda
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
This commit removes the aonpt interrupt masking/unmasking needed after
wake up as that functionality is now available in QMSI 1.4. The QMSI
save/restore functions are called instead.
Change-Id: I61a4a6952e959d0834904bbc8e1eb98092ae4b1c
Signed-off-by: Juan Solano <juanx.solano.menacho@intel.com>
This commit removes the RTC interrupt masking/unmasking needed after
wake up as that functionality is now available in QMSI 1.4. The QMSI
save/restore functions are called instead.
Change-Id: I15b5063fa64c71b125edd2c709410b5ae655032e
Signed-off-by: Juan Solano <juanx.solano.menacho@intel.com>
Several GPIO device drivers support only one of the two possible
access_op modes and return an errno error code for the mode they do
not support. Use the same errno code across all drivers.
Change-Id: Ic01ce9dee7fb2405d254c60cebee22053c803270
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Several GPIO drivers detect an out of range pin number and return an
errno error code. Use the same errno code across all drivers.
Change-Id: I0e2949432d6845d12c37064c78f9c228b8e8e45a
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Several gpio drivers consider GPIO_INT with GPIO_DIR_OUT to be illegal
and return an errno code. Use the same errno code across all drivers.
Change-Id: I1594df0cfdf96194685c83c34dff36261896f2de
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
This flag is no longer necessary and TICKLESS_IDLE will be
enabled by default if SYS_POWER_MANAGEMENT is enabled.
Jira: ZEP-1325
Change-Id: Ic6cd4b8dc0a17c6a413cabf6509b215a4558318d
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Update the builtin QMSI code to 1.4 (RC2).
The below shim drivers were updated for API or interface changes:
- aio
- counter
- i2c_ss
- rtc
- wdt.
Also, arch soc specific power management code were updated.
Jira: ZEP-1572
Change-Id: Ibc8fae032a39ffb2c2c997f697835bc0208fd308
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
If subcription was found within the subscription list,
we have check if remains identical subscription
from the next node.
Otherwise none unsubscription is realized.
Change-Id: I38132d7c80575801885b8057902f3d4666b08aea
Signed-off-by: Jonathan Gelie <jonathanx.gelie@intel.com>
This commit changes the net_buf getter functions in nbuf.h
by adding a timeout parameter. These function prototypes
are changed to accept a timeout parameter.
net_nbuf_get_rx()
net_nbuf_get_tx()
net_nbuf_get_data()
net_nbuf_get_reserve_rx()
net_nbuf_get_reserve_tx()
net_nbuf_get_reserve_data()
net_nbuf_copy()
net_nbuf_copy_all()
net_nbuf_push()
net_nbuf_append()
net_nbuf_write()
net_nbuf_insert()
Following convinience functions have not been changed
net_nbuf_append_u8
net_nbuf_append_be16
net_nbuf_append_be32
net_nbuf_insert_u8
net_nbuf_insert_be16
net_nbuf_insert_be32
net_nbuf_write_u8
net_nbuf_write_be16
net_nbuf_write_be32
so they call the base function using K_FOREVER. Use the
base function if you want to have a timeout when net_buf
is allocated.
Change-Id: I20bb602ffb73069e5a02668fce60575141586c0f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit changes Kconfig prefix for ieee802154 drivers to
IEEE802154_*. This is done for consistency with config prefixes
used in other subsystems.
Change-Id: Ibbb4d96d2b748f4f13135bde85304ec34c5a90a6
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
The driver was using net_buf_unref(). This technically works
ok but debugging the network buffer allocations is more
difficult if done like this.
Change-Id: If3453a49337c7a359c8af22cfdf331fccc697af5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit splits 802.15.4 drivers configuration into separate files.
Change-Id: Ie1bed862e8f4248240fef18bc211d0ee8ca1493c
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
The DW i2c driver chooses to return -EPERM following a PCI error in
driver configuration. This seems an odd choice. All of the other I2C
drivers return -EIO for general failures detected during driver
configuration.
Switch the DW driver from EPERM to EIO.
Change-Id: Ia4f96386620319736ae4c09212b0a05ea38169b1
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The I2C drivers handle an empty list of I2C messages inconsistenty.
There are two different behaviours, one set of drivers dectects a
requests to transfer zero messages and return -EINVAL while the other
group simple transfer no data and return success.
Adopt the latter behaviour consistently across all drivers. Update
the i2c.h API documentation to reflect this behaviour.
Change-Id: I427fc1b0e18ddc04b7b59c294e0240b3d6ca4073
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Subscribe value is set to zero before calling notify callback,
to distinguish a subscription failure from an unsubscription
on disconnection (when flag BT_GATT_SUBSCRIBE_FLAG_VOLATILE is set).
Change-Id: Ia91220492d82041b2c385bf88a15180387e7a483
Signed-off-by: Jonathan Gelie <jonathanx.gelie@intel.com>
Some application protocol required non-persistente subscription
across connection even in bonded case.
Flag BT_GATT_SUBSCRIBE_FLAG_VOLATILE specify if subscription
must be remove during disonnection.
Change-Id: I1bc2bbbb4bc86f58905e44a7eb267ca0871f2fdb
Signed-off-by: Jonathan Gelie <jonathanx.gelie@intel.com>
Implement the missing port read and write behaviour.
Change-Id: I0928379eddf81d806a0ae6b75a1ea2993c3a28ff
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Adjust the implementation of gpio_pin_read() to return 0 or 1 rather
than 0 or 2^pin. This ensures consistent behaviour with other gpio
device drivers, and conforms to the behaviour documented in gpio.h by
the previous patch.
Change-Id: Ia02aa68105a406f355d16a3f9b0550f948658483
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The subscriptions callback may free or reuse the subscription so all
instances that where this could happen need to safely fetch the next
element which is why this changes switch to use sys_list_t as it has
SYS_SLIST_FOR_EACH_NODE_SAFE.
Change-Id: I37d51f27116ea0c057b560924a9416676477597b
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reduce the pressure on the common RX buffer pool by reusing HCI
command buffers also for the Command Status or Command Complete
response to them. This also implies removing the existing Kconfig
variable for the command buffer sizes since the size is also dependent
on maximum Command Complete event sizes. Instead, reuse the RX buffer
size also for HCI Command buffers.
Change-Id: I006b287d64a0c9ca40de741aa9a424a49a927385
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A subsequent patch will start reusing HCI command buffers for
receiving the response, so the distinction of received vs sent data
headroom would just make the code unnecessarily complex. Instead, just
merge these two variable into a single one.
Change-Id: I31d846331939f1a2270df7ed0c75112825e16493
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If we are low on RX buffers and receive an LE Advertising Report or a
BR/EDR Inquiry response we should just discard this. If we don't
discard the event we increase the risk of deadlock where the RX
interrupt is enabled but bt_recv() is doing a synchronous HCI command
sending, i.e. waiting for a cmd_status/cmd_complete (which will never
come since the RX interrupt is disabled).
Change-Id: I6266625c9790d68bcf8e8718c8c36f127946c4c6
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add sensor sample ready check before fetching the sample.
Otherwise, invalid value will be returned.
Jira: ZEP-1532 ZEP-1358
Change-Id: I570151c8ae93fbb744dac857521f596fd63806a6
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
riscv defines the machine-mode timer registers that are implemented
by the all riscv SOCs that follow the riscv privileged architecture
specification.
The timer registers implemented in riscv-qemu follow this specification.
To account for future riscv SOCs, reimplement the riscv_qemu_driver by
the riscv_machine_driver.
Change-Id: I645b03c91b4e07d0f2609908decc27ba9b8240d4
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
This is a zero-copy networking implementation of Ethernet driver.
Limitations:
- one shot PHY setup, no support for PHY disconnect/reconnect
- no support for devices with DCache enabled due to missing
non-cacheable RAM regions in Zephyr.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1492
Change-Id: Ib944f91193efbd12c1142b0bcf1f635388bf1b87
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added basic USART driver for Atmel SAM MCU family. USART is a very
comprehensive module, currently only basic features sufficient to
support printf functionality are implemented by this driver.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Ia9710e4069243fb6c30de45953dfc1fe1266b63a
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
I found that I was not getting the i2C interrupt.
When CONFIG_I2C_0_IRQ_DIRECT=y, it is acceptable to just
pass the constant to irq_enable.
See ZEP-1651.
Change-Id: I10955e6d6fe5fdd2dda916c92c8bc8a2e871f41a
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Replace _ScbExcPrioSet with calls to NVIC_SetPriority as it handles both
interrupt and exception priorities. We don't need to shift around the
priority values for NVIC_SetPriority.
Jira: ZEP-1568
Change-Id: Iccd68733c3f7faa82b7ccb17200eef328090b6da
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a shim layer around the mcux lpuart driver to adapt it to the Zephyr
serial interface.
NXP has multiple uart hardware blocks that implement different features
and have different register maps. The k64 has a uart block called
'uart', while the kw41 has a uart block called 'lpuart' (low power
uart). The MCUXpresso SDK provides separate drivers for each type of
uart block but with similar software interfaces. As a result, there are
also separate shim drivers in Zephyr. There is a 1:1:1 relationship
between hardware block, mcux driver, and mcux shim driver.
Because we now have two mcux shim drivers for the uart interface, a new
naming convention is created:
<interface>_mcux_<hw block>
Where <interface> is the name of the Zephyr interface, in this case
'uart'. This convention is not new.
<hw block> is the name of the NXP hardware block, in this case 'lpuart'.
This is the new part, and distinguishes different hardware blocks
for the same interface.
Change-Id: I3a80b9bffa116bbb2b02ee950d4bdd79a19a4edc
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The newer version of mcux changes its flash api slightly, so update the
Zephyr shim accordingly.
Change-Id: I0c974fc3e82b9f40372c636f0b805ed143be2198
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
spi_transceive can return successfuly even if the data provided by the
slave is invalid, so check if the content is correct and retry until a
valid data is available.
Change-Id: Ia951de391e0b24c5b41eeabfb5c10b056d32b62e
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Drop the BLUETOOTH_SPI_RX_BUFFER_SIZE and BLUETOOTH_SPI_TX_BUFFER_SIZE
config options by fixing the max SPI buffer length to 255, as used by
the X-NUCLEO-IDB04A1 BSP. This simplifies the rx/tx buffer handling, and
avoids a potential spi rx stack overflow depending on the config values
set by the user.
Change-Id: Ifa7fd086016abda4bdcf9638f28b38d001a288c5
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
This new option is used to encapsulate the logic specific to devices
implementing the BlueNRG Bluetooth stack (e.g. X-NUCLEO-IDB05A1).
The current BlueNRG specific logic covers the HCI Reset handling and
the manual control of the SPI Chip Select line (normally not needed since
spi_transceive is also responsible for controlling the SPI CS line).
Change-Id: I5db4addf873eee0af2d957e2181c50aac53ab656
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Change BREDR_NAME to DEVICE_NAME so it can also be used as the LE
device name.
Change-Id: I9ef55d9dff098372d47d9d5754ad7a7163a65bc0
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Code was assuming that all the HCI messages were events, causing invalid
data length when receiving HCL ACL packets.
Change-Id: I8c1a07f46b6b62a04e242cf29ee1119f59d4bda6
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
SENSOR_CHAN_*_ANY will be deprecated, so use the new SENSOR_CHAN_*_XYZ
enum values.
Change-Id: I91cf25864613a934feab65588969d10c52fd4fe6
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Thus users won't have to first enable network stack and then telnet.
Change-Id: I30cb2b9debee3feaf804f9a70f9d3f90758f5f17
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The cause for this change is TCP. Until now, the radio strategy driver
(ALOHA or CSMA) was providing the actual nbuf, and not the buffer
fragment, counting on the fact that the loop was using
net_buf_frag_del() which made so, iteration after iteration, buffer
framgent to be always buf->frags. The problem with this logic is loosing
the fragments that might be still referenced by TCP, in case the whole
buffer did not make it so TCP can retry later and so on.
Instead, TX now takes the nbuf and the actual frag to send. It could
have been working with just a pointer on the data, and the whole length
of the frame. But it has been avoided due to possible future devices,
that will be smarter and run CSMA directly in the hw, thus it will
require to access the whole buffer list through the nbuf.
Change-Id: I8d77b1e13b648c0ec3645cb2d55d1910d00381ea
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is the skeleton for such support. Let's see if this will be needed
and thus extended in the future.
For now, it's disabled by default, not advised to be enabled.
It supports AYT, AO and DO/SUPR_GA. This is very limited and only there
to show how it could be handled.
Change-Id: I736bfa23145e9b727af08db682ab001f494f8c8d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Telnet "Interpret As Command" (IAC) code is ignored.
Change-Id: I882397389d77b8adfcbce62fbd9654c0b0412ae3
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Let's use the generic console input type now. This will be useful for
other console input drivers such as telnet.
Change-Id: I787a1e9d86481d5f8c4803453726d9042a89dea4
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Input line length can be modified via Kconfig.
Change-Id: I3423fce9814e04b11d11e5d391f85fe1efbe8d17
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Basically missing {} on if statements.
Taking the opportunity to remove a useless switch.
Change-Id: Ic6b3951dfc257cb46d858ebcd12bdf1b4e7ff997
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Telnet is started as an application, as it requires the net stack to be
ready. It will listen to any IP address on both protocols (IPv4, IPv6),
depending of course on which one is enabled.
Current behavior is very basic, as it does not handle any telnet
command (IAC). These will be silently ignored.
Jira: ZEP-1601
Change-Id: Id50656f23e6347bbbc893416953f1ba7116ef87d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of TI_CC2520_CHANNEL option NET_L2_IEEE802154_ORFD_CHANNEL is
used.
Change-Id: I9b0c0ff6b2c42070d05c5cf3e4dc33c364be9a5c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add driver and configuration for the MCR20A 802.15.4
transceiver.
Jira: ZEP-1429
Change-Id: I0b17b688220a47c2f0e5cde269064bbd0dec824a
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Fixes fxos8700_gpio_callback() to pass a pin number to
gpio_pin_disable_callback() rather than a pin mask.
Jira: ZEP-1507
Change-Id: I15bfbf4d3377f22942aa549377472d2b1142c32b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Remove dev driver and integrate it in the default pinmux driver.
Jira: ZEP-958
Change-Id: I55670240f8a21749d3a6ae22e300e16ba80a2fb6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Basic interrupt driven i2c driver for the NRf5 series.
The NRf5 series hardware imposes a constraint that various peripherals
cannot be used simultaneously. This driver does not implement mutual
exclusion against SPI, or SPIs drivers (yet).
Change-Id: I308d93bc486eef95db7b95c6b7c9beafc0d7e97f
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Extended the nRF5 GPIO driver to support configurable pin drive
strengths.
Change-Id: I59c42b8a69cc37b594c2388b892d3accd7b19807
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Enable gpio driver automatically when an app or upper
level driver needs it as chip select for spi.
Change-Id: I2bed134939426e2c84f313393d638a878c84fbfc
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
The pulse config option requires triggers enabled, so expand the
trigger requirement to also include all the pulse configs.
Change-Id: Ib94f4071cac757b24bfe940ca64fd11b07fed1c1
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
This avoids asm files from having to explicitly define the _ASMLANGUAGE
symbol themselves.
Change-Id: I71f5a169f75d7443a58a0365a41c55b20dae3029
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
Convert driver to use the CMSIS NVIC APIs rather than the internal ones
so we can remove them in the future.
Change-Id: I7bf3024ea4baf61f1e42bbbd5e4b0abfc6c04e6b
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use the CMSIS NVIC APIs rather than the internal ones
so we can remove them in the future.
Change-Id: I31c2f37bc0aa35668a441f4ef2821b768dd7b817
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove use of __scs structures and defines in place of CMSIS defined
ones. Also, use __ISB() instead of inline asm.
Jira: ZEP-1568
Change-Id: I8798206a12680f6c50105c7c28112632ac9dde50
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have a more generic mcux spi driver that can be used across
multiple Kinetis SoCs, remove the specific k64 spi driver.
Jira: ZEP-1374
Change-Id: Ifc324374f305837f5e3d2cfd7ad30d3608865b5b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux dspi driver to adapt it to the Zephyr
spi interface. Unlike the existing k64 spi driver, this driver can be
used for other Kinetis SoCs that contain the dspi module.
Jira: ZEP-1374
Change-Id: I9417c1513565dfcc47ccda098492f60e840f4f84
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds default configurations for baud rate, transfer word size, clock
polarity and phase. These default configurations can be shared across
multiple spi drivers.
Change-Id: I221b402c075003014991b38f6342a89e55c3bec9
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds Dualtimer support to be used as a Timer.
Jira: ZEP-1300
Change-Id: If13143c8a8bdb07210daca66deca44710a18406f
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds Dualtimer to be used as a counter.
Jira: ZEP-1300
Change-Id: Ic4a2d89ec7fc0c0c2a0bc7f6d32d97637049faaf
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds Timer 0 and 1 to be used as timers.
Jira: ZEP-1300
Change-Id: I57112a8ed6f5daa22345e8807e9ebe87bb09e782
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds clock control to the counters based on Timer 0 and 1.
Jira: ZEP-1300
Change-Id: I14499a833fe9720496ab7905bc1466e9b03bb316
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds a common interface for timers and counters based on
CMSDK APB timers.
Jira: ZEP-1300
Change-Id: I1f89f674d31410f19b651cd904c79f8d173a5357
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The NXP copyright should not have 'Semiconductors, Inc' in it.
Change-Id: I6e290146d49bf22d1d40b7fa764bb53b6b122303
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The commit c90e4d063be0ff5f47df45ca8500eff8518c5d25 changed
line 216 in drivers/gpio/gpio_stm32.c:
-elif CONFIG_SOC_SERIES_STM32F4X
+#elif /* CONFIG_SOC_SERIES_STM32F4X */
This causes the following compiler error:
zephyr/drivers/gpio/gpio_stm32.c:218:39: error: #elif with no expression
#elif /* CONFIG_SOC_SERIES_STM32F4X */
^
Change-Id: Ie8b124931e333aa7860e6db22f5c259670e29833
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Now that we have a more generic mcux serial driver, remove the uart_k20
driver.
Jira: ZEP-719
Change-Id: I51a3237454140feabbfe18ac2c8ee451e572c7be
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux uart driver to adapt it to the Zephyr
serial interface. Unlike the existing (and confusingly-named) uart_k20
driver, this driver can be used for k64 and other Kinetis SoCs.
Implements polling and interrupt-driven serial interface functions that
are logically equivalent to the uart_k20 driver. Adds an extra instance,
irq_tx_empty(), and err_check() that aren't implemented in the uart_k20
driver.
Jira: ZEP-719
Change-Id: Iab99542e7ec921ef4f361437768113fee01e5fe8
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Implementation includes adding some defines in the pinmux,
adjusting gpio driver to specific defines for STM32F3X family,
adding specific functionality in the F3X SoC definition.
Change-Id: I465c66eb93e7afb43166c4585c852e284b0d6e67
Signed-off-by: Adam Podogrocki <adam.podogrocki@rndity.com>
FXOS8700_THREAD_PRIORITY and FXOS8700_THREAD_STACK_SIZE need to also
depend on FXOS8700_TRIGGER, else they will not show in the fxos8700
menu entry when running "make menuconfig".
Change-Id: I8f59125157f046592f3c92dcf2a92bd0e407cd6a
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
The rationale for removing fragments while sending them is to free the
memory they're using as soon as possible. This worked fine because
most protocols implemented initially did not require any
retransmission, so the upper layers were never holding an extra
reference to the buffer (& their fragments).
This is not the case anymore, as the TCP layer holds a reference to
a buffer (& fragments) while confirmation from the peer has not been
received, allowing retransmission.
With this change, the fragments of a buffer are not removed when being
sent by the SLIP layer; however, the buffer is still deferenced when the
transmission is complete. If nothing else holds a reference, all the
fragments are returned to their respective pools, like before.
Change-Id: I74966d72f6970b66f526ea0b765101077c843de2
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
All sample applicatons in Zephyr, using the ENC28J60 driver, set
the ETH_ENC28J60_0_GPIO_PIN Kconfig variable to 19.
However, in the Kconfig.enc28j60 file this variable is set to 24.
That default value, 24, was used only during the first iterations
of this driver and never used again.
In this patch, we set the Kconfig variable to 19 and simplify
project configuration files by removing one line.
Change-Id: I3d5fd9da04a3f10845d2a409de56f5b9c235e995
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This is one of the series of patches that simplifies the driver
code by using the IS_ENABLED macro. This removes the need of the
const variable and the three wrapper functions on semaphore APIs.
Jira: ZEP-1251
Change-Id: I5102e8674663ddbfc65220de72c8b778a9ec726c
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
This is one of the series of patches that simplifies the driver
code by using the IS_ENABLED macro. This removes the need of the
const variable and the three wrapper functions on semaphore APIs.
Jira: ZEP-1251
Change-Id: I2ea0b2d04252d6b28e7d5ca528480234545e6eed
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
There was a recent change to the license boilerplate of the entire
source tree, however as this spi.c was just recently added it missed
the change.
Change-Id: Icc95084a4b051266beaf1796c31d9aec9da538d0
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove an unnecessary condition check in Kconfig.
All the config options already depend on I2C.
Change-Id: Ia8876442652df9f105e862d8c2db394699c81f63
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This driver acts as a pass-through, taking raw HCI data, converting
it to SPI comms and vice versa. It works in the same way as the
existing H:4 and H:5 drivers, only it uses SPI instead of UART.
In this first release, the only BLE board which has been tested is
the X-NUCLEO-IDB05A1:
http://www.st.com/en/ecosystems/x-nucleo-idb05a1.html
Although the current supported SPI format works like the one below,
it should be trivial to adapt it to support other chips with a
different format.
SANITY CHECK = 0x02
SPI WRITE = 0x0A
SPI READ = 0x0B
Tx Format:
[HOST] {SPI WRITE} 0x00 0x00 0x00 0x00 {HCI MESSAGE ...}
[CHIP] {SANITY CHECK} {FLASH SIZE} 0x00 0x00 0x00 {0xFF * MESSAGE LEN}
Rx Format:
{IRQ LINE GOES HIGH}
[HOST] {SPI READ} 0x00 0x00 0x00 0x00 {0xFF * BYTES TO READ}
[CHIP] 0x02 {FLASH SIZE} 0x00 {BYTES TO READ} 0x00 {HCI MESSAGE ...}
Change-Id: I4a00711c922d9ea02c5e2afb0d16715e413b1ed5
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This file doesn't even include <bluetooth/log.h> so any tricks on
BT_DBG are completely pointless (and wrong after the recent update to
the debug logging API).
Change-Id: I1b2b7942a11a4f7229dc35aa2701b3180dc35a28
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The new IS_ENABLED macro allows exposing conditionally enabled code
always to the compiler, even though it may not ultimately end up being
built. This is in particular useful for letting the compiler catch any
logging format string errors. Introduce a new BT_DBG_ENABLED macro
that c-files need to define before including <bluetooth/log.h> in
order to choose whether BT_DBG() logs are enabled or not.
When no Bluetooth logs are enabled the patch also modifies the log
macros to have the format strings checked with the help of the
__printf_like annotation and empty static inline functions.
Change-Id: Ie6bc8e10727b5b306f3ed0f94089a07a22583d9b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the use of the IS_ENABLED macro
(https://gerrit.zephyrproject.org/r/#/c/9882), the driver
reentrancy code is simplified:
The original const variable which used to serve the purpose of
making the build to compile out the reentrancy code when the
reentrancy configuration flag is not enabled is no longer
needed as the use of the IS_ENABLED macro achieves the same result.
Also the original 3 wrapper functions around semaphores API are
not necessary; instead, just use the semaphore API directly.
Jira: ZEP-1251
Change-Id: I23552b77d19044dc94de443018759cb3ec10a52b
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Remove the type field from the sensor value structure. All values will
have the type previously defined by SENSOR_VALUE_TYPE_INT_PLUS_MICRO.
This simplifies the interface, as apps will know what value type to
expect. Apps that prefer to use double values can optain them using the
sensor_value_to_double function.
Change-Id: I3588d74258030eb16c3f89d8eead13cca4606b18
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
tested with blinky, button and disco apps
Change-Id: I4b520d4f3e42c97e4a723747ce4a6c67ca9f1d18
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
riscv-qemu UART:
1) comprises only one register that is used to send or
receive characters in a polling fashion.
2) does not have a FIFO and is not interrupt-driven.
Change-Id: I9408f1776eba4cec4aa203a5da759ec04bcddf1f
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
The riscv-qemu timer driver does not implement
TICKLESS_IDLE
Change-Id: I3eeb5abb05b3f16b55ab9343c2045295b3010cfd
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
The pulpino_timer driver does not implement TICKLESS_IDLE
for the time being.
Change-Id: I0cce8c8a7e203d551a924863462e6c86af4c98ff
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
Add common log level for all IEEE802154 drivers.
Change-Id: If92c96b14e630d4482aadf9cacb25662d6663399
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Force-align all variables defined via asm .word to ensure 4-byte
alignment.
The straddled_tick_on_idle_enter variable was a bool, which resolved in
an one-byte quantity. Changing it to a 32-bit integer. It would have
occupied 4 bytes anyway with alignment.
Fixes ZEP-1549.
Change-Id: If5e0aa1a75dbc73d896b44616f059d221fe191c6
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The k64 pinmux driver was deprecated when the more generic mcux pinmux
driver was added, but it can actually just be removed because it is not
a public interface. Applications should be using the public pinmux API,
not the private k64 pinmux API. There was one case in the net samples
that used the private API which was cleaned up in a previous patch.
Change-Id: I49a6397baa57973930cb63bd2a9883b14f7ddafd
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that we have a more generic mcux gpio driver that can be used across
multiple Kinetis SoCs, remove the specific k64 gpio driver.
Jira: ZEP-1394
Change-Id: I177f96a75e441b70c523e74e99f1b7a54eac6b0e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new mcux gpio driver that can be used for k64 and other Kinetis
SoCs. This driver uses mcux CMSIS register accesses to the GPIO and PORT
modules. Some of the logic from the k64 gpio driver was reused and
refactored (mainly flag parsing and callback handling).
Jira: ZEP-1394
Change-Id: If5e9390861c181ec555dce6569b14debb729526a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Changes the init level for the mcux pinmux driver from POST_KERNEL to
PRE_KERNEL_1. This will allow moving the uart console pins from the k64
soc init to the board pinmux tables.
Change-Id: I6d3377c9a689c12711c84387f74843ca9488df52
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Renames the ksdk random generator shim driver to mcux.
Change-Id: I8bc376937fed3024c809782139a0a72c7332f89a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The ksdk pinmux dev driver was previously merged into the regular ksdk
pinmux driver, and the config PINMUX_DEV_KSDK was removed. Two
references were inadvertantly left behind, so remove them now.
Change-Id: I77394be5459d55a9f16e7bd2b3c9d688c4605b4f
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Merges the ksdk pinmux dev driver into the regular ksdk pinmux driver,
which now exposes the public pinmux API. Removes the private ksdk pinmux
API and converts the frdm_k64f and hexiwear_k64 boards to use the public
pinmux API.
Jira: ZEP-958, ZEP-1432
Change-Id: Ie5f60b604133093050b9c596050cad776d7b7cb3
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
On the nRF5x platforms we need always need the NRF_RTC_TIMER and it
depends on the CLOCK_CONTROL_NRF5. So enable all of these always.
Fixes issues if one tries to build nRF5x platforms w/o CONFIG_BLUETOOTH.
Change-Id: I0f9af785e785f37ec289a935ddf70ee6dec08cd4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove legacy option and use SYS_CLOCK_EXISTS where appropriate.
Change-Id: I3d524ea2776e638683f0196c0cc342359d5d810f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove aio disabling code before calling callback. If aio is
disabled before callback is invoked, calling pending
interrupt check API in the callback will get negative result.
If user wants to disable the aio, it can do this in callback
instead of this being done blindly before callback.
Jira: ZEP-1437
Change-Id: I42ebe4584af6396ac2360152f9b0e2c389c44145
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
drivers/gpio/gpio_pcal9535a.c defines a nano_timer,
but never uses it. So delete it.
gpio_sch.c uses a k_timer, but gpio_sch.h defines a
nano_timer. So change the variable poll_timer to
type k_timer.
Jira: ZEP-1525
Change-Id: I884e4703c1ace61da5be7d9c63e58e7c3bce7f68
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
The sensor_attr_set() wrapper deals with drivers that do not support
the attribute set API, there is no need to provide a per driver
implementation that only return -ENOTSUP.
Change-Id: I1568ab018988fc560bd89ab96f2f2256ddd5b7e1
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
UART 16750 is basically a UART 16550 with a 64-bytes FIFO.
The 64-bytes FIFO can be enabled via register FCR.
Account for it in the uart_ns16550 driver whenever the
CONFIG_UART_NS16750 variable is set.
Change-Id: I2342b28a41d03c96410bbfbe57e4b5a4e335731d
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
Since RTTWriteNoLock is not thread-safe or preemptable, it is necessary
to lock interrupts around the calls to it.
Change-id: I38b7e37a0f46e77bf82c1e07d549414393e84a51
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since callers of bt_recv() have so far anyway been required to know in
which context to call it (based on e.g. bt_hci_evt_is_prio) it's
cleaner to have two separate APIs: bt_recv and bt_recv_prio.
Change-Id: Icd0d9aed9c51ffd2def31432c4ffcc16a9f13ccd
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use interrupt based transmission instead of polling.
Change-Id: Iebfd67372044d3e6de9bdbdd6f0c9c6d01d46cb9
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
So far the use of k_sem meant that there was no major benefit of
having more than 2 or 3 RX buffers since there was no queuing
mechanism. Instead of using k_sem, introduce a k_fifo and use that to
queue up incoming buffers. This way the RX buffer count can be
increased with measurable effects on throughput.
Change-Id: I8122b233aeee7c8e145de3fff5f10bcfe348efaa
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The H:5 HCI driver doesn't need the type-specific bt_buf allocation
helpers.
Change-Id: Iccb9803f32f3143f1cdf972d9229124816a99aa6
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Completely redesign the H:4 driver to utilize its own thread and
select the new RECV_IS_RX_THREAD Kconfig option.
Jira: ZEP-1483
Change-Id: I0ca0661b66d564e5edc1b8505706d6bb76632e79
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This option has not been used so far and will only contribute
unnecessary complexity in subsequent patches that introduce a concept
of combined RX buffers.
Change-Id: I53e0ce5155eebc352b84ba41b30ecb9d9958699f
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This helps simplify code that was previously combining net_buf_add()
with memcpy().
Change-Id: If44cf9cd651aba5e544e36567869f147468663eb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This moves the shell component into its own subsys and groups all
related files and options into a single place.
Additionally, one Kconfig option will now be required to enable the
shell:
CONFIG_CONSOLE_SHELL=y
The header files was also moved to include/shell/shell.h and can be now
referenced with
#include <shell/shell.h>
instead of
#include <misc/shell.h>
Updated documentation as well.
Change-Id: Iffbba4acfa05408055e9fd28dffa213451351f94
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
replace include <nanokernel.h> with <kernel.h> everywhere and also fix
any remaining mentions of nanokernel.
Keep the legacy samples/tests as is.
Change-Id: Iac48447bd191e83f21a719c69dc26233216d08dc
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Introduce random device API analgous to other device driver classes in
Zephyr. Modify the the KSDK random driver to implement the API.
We retain the sys_rand32_get() interface for now on the assumption it
will eventually relocate to or be otherwise replaced by an entropy
management system.
The existing TEST_RANDOM_GENERATOR related drivers that do not
generate entropy are not modified to expose this driver API since they
cannot generate entropy.
Change-Id: I60b2d5afddf242e802a1d9014c99579870fb7472
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The GPIO_INT_LEVEL value is zero so the mask assignement
is never executed. Using the bit complement GPIO_INT_EDGE
the proper mask is assigned
This issue was reported by Coverity
Coverity-CID: 151966
Change-Id: Iacfeb6466388023bd6123ba86280aa9ca15f34e4
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Not all users are in an ISR context where we can't block, so give the
callers the freedom to choose if they want to block or not.
Jira: ZEP-1481
Change-Id: I19bd7e2df94c4eeb60886a17a78f872bd7bea887
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When CONFIG_SYS_POWER_DEEP_SLEEP is enabled, spi_qmsi_ss will
keep entering deep sleep because it needs to wait until the
current transfer completes, which blocks the current thread.
The system keeps entering deep sleep again and again and the
transfer will never complete.
Add device_busy_set() to spi_qmsi_ss driver to indicate that
the device is busy and block the system from entering deep
sleep during transaction.
Jira: ZEP-1488
Change-Id: I5a4456933249def93eaa529b30b99d730af74482
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
When CONFIG_SYS_POWER_DEEP_SLEEP is enabled, i2c_qmsi_ss will
keep entering deep sleep because it needs to wait until the
current transfer completes, which blocks the current thread.
The system keeps entering deep sleep again and again and the
transfer will never complete.
Add device_busy_set() to i2c_qmsi_ss driver to indicate that
the device is busy and block the system from entering deep
sleep during transaction.
Jira: ZEP-1487
Change-Id: Ia681d242349bce5a9867e54df4e65dba09005930
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
Enable arc to access the i2c controller on I/O fabric.
There are two i2c controllers on quark se SoC. One is attached
to the I/O fabric and the other one is in the sensor system.
X86 cpu is only able to access the i2c controller on the I/O
fabric and the access is supported by existing code. HW allows
arc to access both controllers. But, the existing code only
gives arc access to the controller in the sensor sub-system.
Let's grant arc the access to the controller on I/O fabric as
well by the following changes.
1. Add i2c_qmsi.c into arc compilation.
2. Use the already defined macros to choose interrupt numbers
and do interrupt unmasking automatically based on the
compilation targets.
3. Add new symbols in Kconfig including driver names for both
controllers
Jira: ZEP-1189
Change-Id: I317da6038c50e0c8bd16f446182c1f8bdf6d3ba2
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Enable arc to access the spi controller on I/O fabric.
There are two spi controllers on quark se SoC. One is attached
to the I/O fabric and the other one is in the sensor system.
X86 cpu is only able to access the spi controller on the I/O
fabric and the access is supported by existing code. HW allows
arc to access both controllers. But, the existing code only
gives arc access to the controller in the sensor sub-system.
Let's grant arc the access to the controller on I/O fabric as
well by the following changes.
1. Add spi_qmsi.c into arc compilation.
2. Use the already defined macros to choose interrupt numbers
and do interrupt unmasking automatically based on the
compilation targets.
3. Add new symbols in Kconfig including driver names for both
controllers
Jira: ZEP-1190
Change-Id: I40a5d423d4b7986a897834d1a3831938005eda6f
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Use new kernel header file and k_sleep from unified
kernel instead of nano timer.
Change-Id: I1c98c07f880382eaa87f6e0c45967a4b8b6bfd7d
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
From code inspection, the driver always took timeouts in milliseconds.
The only sub-ms wait uses k_busy_wait(), which has microseconds
granularity, but its granularity does not depend on the system clock
tick rate.
Change-Id: If48363fd1fbeeb8e5ff0f0f2ca86e671d63bc571
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
It receives a timeout in ms, but was still converting it to ticks, while
the unified kernel API takes a value in ms.
Change-Id: I8ff7f44090716385764fe4b2a087043a2e0d70af
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Adds optional support for tap and double tap sensor triggers to the
fxos8700 driver using the pulse detection hardware function.
Default configuration values were taken from NXP AN4072, section 6.3.
http://cache.nxp.com/assets/documents/data/en/application-notes/AN4072.pdf
Change-Id: Ia95091628a853eb956f6fd1df099a9e6e101b707
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The GPIO_INT_LEVEL and GPIO_INT_ACTIVE_LOW values are zero so the
statements are never executed then is better use the bit complement
masks
This issue was reported by Coverity
Coverity-CID: 157586
Change-Id: Ic8b20660a991dd3d0c71248f84c917e5ce5c3c7c
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Remove the existing code that iterates over k_sem_give() and setup the
initial counter directly, take the opportunity to set the maximum count.
Change-Id: Ib91ea263567ff761e4953c142a22a56658efe293
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The shell_cmd structure has three parameters and only two were
initialized. So, this commit initializes the remaining parameter
and also adds the ARG_UNUSED macro to avoid compiler warnings.
Change-Id: I667a4e9839ec5acd526df0bb465beb2062518315
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Remove the unused argument and comparing int to unsigned int
compiler warnings.
Change-Id: Iad79ec2ef8206b2494875a93551a0f47e234ff8d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Use the right data-type to avoid compiler warnings.
Change-Id: I3e807482c5636f37ef1288689450dbe3c9c04dcf
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch adds the ARG_UNUSED macros to some function
arguments to avoid compiler warnings.
Change-Id: I628aea55d98cf8519c046ae5835e95cfa70a973f
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
To support interrupt-based GPIO callbacks in the nRF5x series one needs
to use the GPIOTE module, which has a series of channels that can be
programmed to trigger interrupts on level changes.
This commit adds basic support for the GPIOTE module within the nRF5x
GPIO driver, as well as callback support in order for basic buttons and
switches to work.
Change-Id: I9ae600f894372ad42b09a18cc38a90fc29abb0df
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To make way for the upcoming blinky and GPIO support for nRF5x-based
boards, this change addresses the hardcoded dependencies in Kconfig
default configurations of the different boards, moving the common option
defaults to the SoC default configuration itself.
Change-Id: I8db0750311ad5a12b76237b39438376f20f6f496
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/basic/blinky
- samples/basic/disco
- samples/basic/button
All 4 GPIO ports are supported.
Change-Id: If8599a23c1d56cfd678a6e2e5339f7e093c6061a
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The new Nordic MDK redefines certain UART signal names for backwards
compatibility with the new nRF52840 IC.
This patch addresses the potential name conflict between the redefined
signals and the existing variable names defined in the UART driver.
JIRA: ZEP-1418
Change-Id: I559d9335d2eeaa0a88d3f261b70508a1c98b989d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Move logging out of misc/ to its own subsystem. Anything related to
logging and any new logging features or backends could be added here
instead of the generic location in misc/ which is overcrowded with
options that are not related to eachother.
Jira: ZEP-1467
Change-Id: If6a3ea625c3a3562a7a61a0ba5fd7e6ca75518ba
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
rename NANOKERNEL_TICKLESS_IDLE_SUPPORTED to
TICKLESS_IDLE_SUPPORTED and remove nanokernel occurances in Kconfig
files.
Make TICKLESS_IDLE depend on hardware that supports it.
Change-Id: I6a2e4fb0f7cf4b45475b48e71823ea089ee98759
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
PRINTK was conflicting, reanme to DBG.
Jira: ZEP-953
Change-Id: If5d6ef385c5ed223f6f7eae9bde887ae4a1b946a
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
That module is not used anymore: it was introduced pre-Zephyr to add
some kind of awareness when debugging ARM Cortex-M3 code with GDB but
was never really used by anyone. It has bitrotted, and with the recent
move of the tTCS and tNANO data structures to common _kernel and
k_thread, it does not even compile anymore.
Jira: ZEP-1284, ZEP-951
Change-Id: Ic9afed00f4229324fe5d2aa97dc6f1c935953244
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The ethernet controller being a freescale one, let's use its OUI. Then
only 3 bytes are needed for generating the rest of the MAC address.
Also, generating the MAC address in the right order.
Change-Id: Id3346ef44f8c24edc2e23dee6ac0581ac58cf4ff
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Left over from old IP stack it seems.
Change-Id: Ic7ce731b8661294125fa0e0e058570aeff7b97cf
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Such stack size might vary if debug is enabled or not and depending also
on other factors. Let's do the same for priority as well, putting it to
high prio as default (15 is way too low level).
Change-Id: I16afab33895085bacdef087fe70adeb1ae3ca2ab
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
ll_len means link layer length, but it's misleading here as ll_len is
the whole net buffer length: reserved ll length + payload length.
Change-Id: If7ec0fc950245d370fa0f82ae1050b05c11c7b90
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
ETHERNET is a left-over from old and now unavailable IP stack.
Change-Id: I488d9ffcfb1fe3589b522dc2d620873daeb892c8
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Note: This driver need to be ported to new native IP stack in order to
be available again.
Change-Id: I7825c8679e66f8a1d44d75c9d53e9da207b743af
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
At this point, if the frame was accepted by the controller, it means
that CRC was valid. Thus, there is no reason to get it in the buffer.
Let's just pop it out from controller's memory.
Jira: ZEP-1361
Change-Id: Ic8681c77b0afa30583c7fae281db1a89ff97ed2b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Directly use AON GPIO trigger instead of IPM.
In the past, SW did not allow arc to receive AON GPIO interrupt.
So, interrupt from BMI160 was routed to x86 cpu. Then, x86 cpu
passed the event to arc through IPM. But, SW was updated and arc
is able to directly receive interrupt from AON GPIO now. So, IPM
is not needed any more. Let's remove IPM related code and use
GPIO as the default trigger source.
This change is on top of the bmi160 sample app change to not use
IPM.
Change-Id: I49d8040764d03b24e09d89e66643c020ef63a3c9
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
The nRF RTC driver, which is used a system clock driver due to the lack
of SysTick hardware on the SoC, was using too much CPU time in its
_timer_idle_exit() implementation due to the use of 64-bit arithmetical
operations. This was causing the ISR wrapper to add excessive latency to
critical interrupts, causing BLE controller asserts.
This patch addresses the issue by using exclusively RTC ticks instead of
OS ticks, thus avoiding the necessity to convert during
_timer_idle_exit() calls, which are the most critical to interrupt
latency.
In addition the driver is now able to detect setting tick events in the
past due to it being interrupted by a higher priority context, and will
reschedule and trigger the ISR at the same time.
Change-id: I56a3be96b9fdd554c3650012d647af2f0415eb8a
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
There are static initializer macros available for most kernel objects
which we should use whenever possible.
Change-Id: I496f4d05d26801eddd21fae53bdd4fcdc3246fe3
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When going into DEEP_SLEEP state, the ARC timer
needs to be restored.
This implements the function to restore the timer
after sleep.
As the time spent during sleep is not currently known,
the timer is expired to reschedule the application task.
Jira: ZEP-1224
Change-Id: I22a30d0fd79f177cf166b9a29dc78d68f7d7fbad
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
In order to resume the ARC from deep sleep,
the interrupts need to be restored.
The FIRQ stack needs to be saved and restored
when performing sleep operations.
During early initialization, the sp in the 2nd register bank
is made to refer to _firq_stack.
This allows for the FIRQ handler to use its own stack.
Fast Interrupts cannot be used after sleep if this information
is not restored.
This patch adds the suspend and resume functions.
Jira: ZEP-1223
Change-Id: Ic81980f05aee6c1f7b8c46c743f2648c65b29486
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Move interrupt initialization for the ARC to its own
device. The init function for the arc will be only
doing platform specific operations
Jira: ZEP-1288
Change-Id: Icb04c3622890021c65cd24cecf6cafee6c37caf9
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
In order to keep the initialization process light-weight, remove
net_buf_pool_init() and instead perform the initialization of the pool
and buffers in a "lazy" manner. This means storing more information
in the pool, and removing any 'const' members from net_buf. Since
there are no more const members in net_buf the buffer array can be
declared with __noinit, which further reduces initialization overhead.
Change-Id: Ia126af101c2727c130651b697dcba99d159a1c76
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Restructure the RANDOM Kconfig to match the structure used in other
drivers with a single top level menu. Move the true random number
generators to appear first in the menu, with pseudo generators at the
bottom. Do not present pseudo generators if a true random generator
is presented.
This change implies that tests, samples and applications that require
the random driver interface must now select CONFIG_RANDOM_GENERATOR.
In order for tests and samples to build (and run) on platforms that
have no random driver it remains necessary to select
the CONFIG_TEST_RANDOM_GENERATOR.
Note that CONFIG_TEST_RANDOM_GENERATOR retains its original purpose of
enabling a random driver that delivers non random numbers for the
purpose of testing only.
Change-Id: I2e28e44b4adf800e64a885aefe36a52da8aa455a
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Update drivers to return INT_PLUS_MICRO values instead of doubles.
This hides the fact that the drivers use floating point operations and
doesn't force the application to use them as well.
Change-Id: I14c6faecb35331c2fdbdab41bc624d751de984b8
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Use integers for sensor value calculations in which doubles are not
required.
Change-Id: I8662023ca596cb232e31849b0b77ae2bf0372cf0
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Remove SENSOR_VALUE_TYPE_INT as it is the same as
SENSOR_VALUE_TYPE_INT_PLUS_MICRO with val2 set to 0.
Change-Id: If5a9c579b7267701c27f40fd887acae47d64edc5
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Until now it has been necessary to separately define a k_fifo and
an array of buffers when creating net_buf pools. This has been a bit
of an inconvenience as well as blurred the line of what exactly
constitutes the "pool".
This patch removes the NET_BUF_POOL() macro and replaces it with a
NET_BUF_POOL_DEFINE() macro that internally expands into the buffer
array and new net_buf_pool struct with a given name:
NET_BUF_POOL_DEFINE(pool_name, ...);
Having a dedicated context struct for the pool has the added benefit
that we can start moving there net_buf members that have the same
value for all buffers from the same pool. The first such member that
gets moved is the destroy callback, thus shrinking net_buf by four
bytes. Another potential candidate is the user_data_size, however
right not that's left out since it would just leave 2 bytes of padding
in net_buf (i.e. not influence its size). Another common value is
buf->size, however that one is also used by net_buf_simple and can
therefore not be moved.
This patch also splits getting buffers from a FIFO and allocating a
new buffer from a pool into two separate APIs: net_buf_get and
net_buf_alloc, thus simplifying the APIs and their usage. There is no
separate 'reserve_head' parameter anymore when allocating, rather the
user is expected to call net_buf_reserve() afterwards if something
else than 0 headroom is desired.
Change-Id: Id91b1e5c2be2deb1274dde47f5edebfe29af383a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This issue was reported by Coverity
Coverity-CID: 157621
Change-Id: I7f84c0868467ab55e033aecac037967da001a6db
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Device sync APIs are actually wrappers for semaphores.
Let's replace them with semaphores.
Jira: ZEP-1411
Change-Id: Ic37972a631f0bfd7bc45f28088e1c423151b1612
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Device sync APIs are actually wrappers for semaphores.
Let's replace them with semaphores.
Jira: ZEP-1411
Change-Id: I02c7cba21d21ff9288e452121e3b7ebb7d251bb4
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Device sync APIs are actually wrappers for semaphores.
Let's replace them with semaphores.
Jira: ZEP-1411
Change-Id: I5662057222aec54f02db9d9cdcd7f4f006c6c530
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Use the SYS_INIT() mechanism to invoke the sys_rand32_init() function
in random drivers that require an initializer. Remove all empty
sys_rand32_init() instances.
The existing explicit sys_rand32_init() function runs immediately after
PRE_KERNEL_2 before stack canaries are initialized. In order to get
equivalent behaviour with sys_rand32_init() we set SYS_INIT() to
initialize the random drivers at the lowest priority of PRE_KERNEL_2.
Change-Id: I4521e44daac806bc4eef01ce7fdf2ba5367e0587
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Basic interrupt driven driver for the nRF5 onboard temperature sensor.
Change-Id: Id0ac303293b8e8b8285b19bcda31284ee6617105
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Now that we have a more generic ksdk pinmux driver that can be used
across multiple Kinetis SoCs, deprecate the specific k64 pinmux driver.
Jira: ZEP-1393
Change-Id: I11cfe9a53746a6e85eced2a7cecf0396d42a7a19
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Kinetis SoCs contain one or more PORT modules to handle pin muxing and
pin configuration. Unlike the existing k64 pinmux driver, this driver
handles each PORT module individually and can be used for other Kinetis
SoCs.
This driver uses KSDK CMSIS register accesses to the PORT module rather
than the KSDK PORT driver (fsl_port.h), because the Zephyr pinmux
interface contains both set() and get() functions to access the pin
configuration. The KSDK PORT driver only contains a set() function
(which is a very thin static inline function to modify the PCR
register), therefore building a shim on top of it would result in a
strange mix of using the KSDK PORT driver for the set() and a direct
CMSIS register access for the get().
Jira: ZEP-1393
Change-Id: I2f7c6b08b207350697d590dcd665223f81de9f9e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
subdir-ccflags-y +=-I${srctree}/subsys/net/ip isn't need so lets
remove it.
Change-Id: I60d97ce25398d7d3801e837075dbf75d1375e055
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
ccflags-y += -I$(srctree)/kernel/unified/include isn't need so lets
remove it.
Change-Id: I910bbac4a189de965d844f5fc36571e8dcb5705d
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We can locally reference the file we need, so don't add a -I we don't
need.
Change-Id: I4d9507d5368073443dcc78a5821fe09d3e0b9bfc
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We can locally reference the files we need, so don't add a -I we
don't need.
Change-Id: I764aea4177a8995489e0f15f71f7373427b43394
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There's now snprintk available that's more light-weight on the stack
than snprintf.
Change-Id: I6b3e4409703ca92fe6b8f4146ff47c490ab826cb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SYS_LOG macros now map to printk by default, and printk doesn't
(currently) support %2.2x, rather %02x needs to be used instead (it
gives the same result).
Change-Id: I0f7a5b7da91afba0c970bce7e2680de40c917bd3
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix compilation issues that show up if SYS_LOG is mapped to printk
instead of printf. Unlike printf, printk is annotated so that the
compiler catches incorrect format specifiers passed to it.
Change-Id: I4d6f635a0ed61de698727028ea8767dc0ef28bb1
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Provide PWM driver for STM32 series F1/F4/L4.
Driver is ported on STM32Cube HAL and should support other STM32
series with minor updates.
Configuration is done so that PWM sample driver could be run on
all nucleo boards supporting PWM driver.
Change-Id: I6522a565451085df932e0eefd8404268380b5bfe
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add pin config for PWM support on ST Nucleo boards
Following config is chosen:
-PA0/PWM2_CH1 for F401RE and L476RG
-PA8/PWM1_CH2 for F103RB
Change-Id: I013e15ed35360d7777bb24ff94e0830f913a6580
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds Timer 0 and 1 to be used as counters.
Jira: ZEP-1300
Change-Id: I9d8b971d8a3d76eee2f9cc4600e95729d67717a3
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add driver for CMSDK (Cortex-M System Design Kit) APB WDOG. This device
uses NMI as interrupt hence it requires Runtime NMI (CONFIG_RUNTIME_NMI)
to be configured in the platform.
Tested with drivers/watchdog sample application.
Jira: ZEP-1300
Change-Id: Ib318047109af81e32060e80d456ef3873fd380ea
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch enables the clock control interface into the ARM LTD
CMSDK APB UART driver.
Jira: ZEP-1300
Change-Id: Ic0a214beb02d56ffb02ad4e6ca26b80805c0a4e6
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch enables the clock control interface into the ARM LTD
Beetle GPIO driver.
Jira: ZEP-1300
Change-Id: I576767b68a8e4aa965d34716528df3bb4e837d73
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the clock_control implementation for the ARM LTD
Beetle platform.
The main features enabled are:
* Clock on and off in ACTIVE, SLEEP and DEEPSLEEP mode.
* PLL support (freq: 12, 36, 48 Mhz).
The integration with the existing drivers will be done in future
patches.
Jira: ZEP-1300
Change-Id: I07cb2325275bd86a036e8e24aeb7bbf2c6176a93
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add board support for the Nucleo64 L476RG development board.
Change-Id: Ibb5424bc936c67a5d96855617202136d7dea772c
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the I2C for the STM32Lx series
Change-Id: Id1694aeb3606b4fa9772bfb7a9f60e48a7cc93a8
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add all possible pin assignment definitions for I2C{1-3} on STM32L4xx.
Change-Id: I2d4266bc3bb9ba41b74a80567c0b04a89963753e
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add macro for all the available pinmux for the USARTs present on
STM32L4.
Change-Id: Ie4352750e1c6f08642b3e222b57f2a791f08ef74
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add EXTI support for the STM32l4XX family.
Change-Id: Ia92f26eaf49899ea23fae05dd3a7357007c9db20
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the support for all the GPIO port of the L4.
Change-Id: Id365e17223cd5c49443df9fb6b96a3c4f204f523
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the clock driver for the STM32L4 series.
Change-Id: Icdf79061f163d8d00187b382d1564422fb875c5b
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Deal with STM32L4X additions for clock and interrupt handling to the
uart driver.
Change-Id: I6e8dafb132dafea54b8f31a3a5cb6e35a207574d
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There was a misalignment between Zephyr UART device numbering and
SoC UART IP. Device "UART_1" was mapped to IP USART_2, which could
be confusing for user.
This commit allows to align "UART_1" to IP USART_1.
Change is propagated to all STM32F103RB/STM32F401RE based boards and
respective pinmux drivers
Change-Id: Ia8099dfeec7b9c0c686c2a58ccb4dbb1a55b6537
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32Cube based implementation allows single driver file for
all stm32 based SoCs.
By maximizing code reuse, use of STM32Cube eases new SoCs
porting into Zephyr and provides better maintanability and
maturity.
Change-Id: Ief4b723add3dfc8b2a839683559c5a4c5d5eb837
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit replaces the nanokernel.h include by kernel.h.
Change-Id: Ib42fbf2d9f77a73c0831f569b3dbbfb342ea2e1d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Adds general sensor triggering support to the fxos8700 driver, including
options for the driver to use its own thread or the global workqueue
thread to handle sensor interrupts. Adds specific support to handle the
data ready sensor trigger.
Jira: ZEP-1395
Change-Id: I092f22e35747b92a88eb71a3d162a4fc16227b45
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch fixes RX overflow error in the k64 SPI driver.
Jira: ZEP-1351
Jira: ZEP-1352
Several circumstances lead to an RX overflow:
The RFOF_RE (RX fifo overflow) must not be set as default.
The flag is only set when rx_buf is available. Also it must
be checked inside spi_k64_isr whether RFOF_RE has been set or not.
If the rx_buf is not available and the incoming data
should be ignored, then MCR_ROOE need to be set.
Since it is not possible to change the MCR register
during the transfer, RX fifo must be emptied
if rx_buf_len < tx_buf_len.
The driver also uses spi_data.xfer_len now,
the variable was already defined. Now, transfers are also
possible if tx_buf_len < rx_buf_len (e.g. read slave device register).
spi_k64_push_data has been adjusted accordingly.
The patch simplifies the handling of interrupts.
The interrupts are also switched off in the event of an error.
The patch also fixes a few coding style issues.
Change-Id: I6ce81f595bb1edbbf2253b6595602896ca652762
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Remove non existent CONFIG_SPI_DEBUG and replace cnt
with DBG_COUNTER_* macros.
Jira: ZEP-1351
Jira: ZEP-1352
Change-Id: I1fba7aaead1ad0b36297b069e5a83e25b7991588
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Clear RX and TX FIFO before starting transfer fixing RX overflow issue
on FRDM K64F board.
Change-Id: I9345a0058a6c7958a6ecf3dc23b99fe7bff18796
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Logging in spi_k64 driver is based on printf-like functions and does
not make sense with syslog which adds additional information like
function name and new line already.
Change-Id: I84a81ebf5c3cc94b311a2e41bdb5f014432d2b09
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Use configured init priority same way it is used for other SPI
drivers. Default priority initializes SPI before console hiding
possible errors and debug messages.
Change-Id: Iddc9c783290d852caa8a9385de4ab114f8f7a2e3
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Fixes following error:
...
drivers/spi/spi_k64.c:717:86: error: 'cnt' undeclared (first use in
this function)
...
Change-Id: If49fa4838265cd39a6f72eb265388ff7faae9a9e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The Real Time Terminal functionality of the Segger J-Link
debug probe and software suite allows applications to write
to a certain RAM area that is read in real-time by the
debugger. This is specially useful when a UART is not
available to provide a console.
This commit adds a console driver that outputs over an RTT
"connection".
Change-Id: Ifce8020060e9f519a61f3f1fbe9f56f98da2ef7f
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add function return value check. This was caught by
Coverity.
Coverity-CID: 157124
Change-Id: I93b23325d657dc787300908b9117b6976617fdba
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Fibers do not exist anymore in unified kernel.
Also, let's just use that option directly so removing the internal
define which is then useless.
Change-Id: I1179d84401934b339d3a9ccd12f6145a120bcb2f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Other driver than QMSI might have this limitation. Let's wait for a
future rework of SPI API to properly fix that.
Change-Id: Ibad382ce86e7479961b275c4851abf88ed581023
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Currently it's only possible to configure those GPIOs through
boards.<h/c> files and thus it's not relevant for board that do not
embed cc2520 but might get one wired to it, unlike
quark_se_c1000_devboard which directly embeds one cc2520.
Change-Id: I819bc1d2de707ea12eb70dc60a40b28f92666e51
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
* Moved networking code into subsys/net.
* Renamed net/yaip to net/ip at the same time.
* Fixed the tests/net to compile
* Fixed the Makefiles and Kconfig files in subsys/net
to use the new location of the IP stack
Change-Id: Ie45d9e8cb45a93fefdf969b20a81e3b1d3c16355
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The cc2520 driver RX thread did not like the stack information
collection macros defined in net_core.h. Both the cc2520 TX and
RX got the same variable name which did not compile.
This is now changed so that the first parameter is added to
the variable name to create a unique variable.
Change-Id: Ia41d01a71afd73af2ef31aa5f7a890a3cf0385aa
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the native IP stack is now the default, there is no need
for corresponding Kconfig option.
Change-Id: I08e4992f540f928a2b7378e8803e634e38725348
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit removes the legacy Contiki based uIP stack.
The new native IP stack must be used after this commit.
The commit also removes following things:
- legacy cc2520 driver
- legacy ethernet drivers
- legacy IP stack samples
and changes these things:
- disabled tests that only work for legacy IP stack
- select new IP stack by default
- enable random number generator by default as it is needed
by the new IP stack
Change-Id: I1229f9960a4c6654e9ccc6dac14a7efb9394e45d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The default kernel init priority is too low. Make this
configurable and set the default priority so that the
ethernet driver is started just before the network stack.
This commit adds generic ethernet priority and changes
currently available ethernet drivers to use it.
Change-Id: If695e52b6dd9ea227f10ba306bb145d72d2312b0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Refactor code to exit earlier in case of error.
Change-Id: I9ff893f923ff877d69b0e985bb6e4159504e67cd
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The original commit:
https://gerrit.zephyrproject.org/r/#/c/6256/
has changed because an internal rebase. Two lines adding an SPI
command are missing.
This commit adds back the missing lines.
Change-Id: I5cbeda73ef1eae5eb98dfa3b7f3086b7438da9a9
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
Use the stack declaration macro from net_core.h which
allows user to see more information about stack usage
when using net shell.
Change-Id: Id3cc0fa49c5da79ba7d5573103864f1881e2f2e5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Hack in commit-id 835f93b8250abc0f3edbee9a99463fccac03597c was breaking
raw mode needed for wpan* adaptations.
Change-Id: If1ff96fa8170cc84e356fb0452e487f0ff174da5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is a hack, related to:
commit-id 835f93b8250abc0f3edbee9a99463fccac03597c
Change-Id: I7e305cef9ca908e2a71a011920663e1603ad8d6e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The 802.15.4 frame has a header and in the end after the payload a CRC.
Overall MTU is 127 bytes, but CRC is most likely going to be generated
by the device itself (offloading). Because the limitation of current
nbuf, it's not possible to keep this CRC in the buffer because it
require a user data size of 127 bytes but if we do so, IP stack will
fill in as much as it can as packet data, thus occupying the 2 last
bytes. This generates bugs. A perfect solution would be to generalize a
better handling of MTU and head or tail reserve data into nbuf, but
this will probably be solved in the future.
Change-Id: I1a0fee4d555e2717c1edd5afba399a1f17d9c7a9
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
commit-id 67c465d2cc introduced this
weird format by not removing unnecessary spaces.
Change-Id: I964185c8a894cfcf10e253e6d378c63ec02ad8d7
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Since the whole init level changes: all drivers and most of subsystems
are initialized at level POST_KERNEL. Unfortunately that broke legacy
tweaks on what to start first and after.
Let's raise cc2520 priority, still below net_init.
Jira: ZEP-1261
Change-Id: I0d91aa87a893584b3f5b39a193c823127961402f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Thus setting a high priority of 2 on the rx fiber, as 0 is invalid.
Change-Id: I44a95f3648ca3fbf2eb699f1fa36963d6f3e5021
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
And take the opportunity to reduce the buffer size, as 127 is the 15.4
MTU, it has just engouh space on 128 bytes for the spi cmd plus the
frame.
Change-Id: Ifdeb83f85ab1adcdebc55bd72c38a98f18a86dbc
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Current value (100) is outside the default values: 0 - 15.
Jira: ZEP-1231
Change-Id: Ib3120b52e6eb3d95b369debd7df541fa2b0dfa6e
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Looks like getting an SFD interruption is not 100% reliable, so let's
just use a semaphore with a timeout on it instead of using
device_sync* routines.
Change-Id: I4e4115c7b939c95d7e75fbb33664d411e0a6e8cc
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Flushing rxfifo is necessary only on complete failure. It's badly
documented, but cc2520 errata mention that srxflush instruction should
be avoided as much as possible because it generates garbage in rxfifo
and kills incoming rx packet.
Change-Id: I486f7f4179103cf0c86c206821a0a61fec06178a
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
15.4 drivers are supposed to append LQI byte in the end of the buffer,
but of course there is no such thing in uart-pipe. Thus the bug, so
let's announce the proper length even if such LQI is missing.
Also align the debug output to proper length (FCS included)
Change-Id: Ib9ad86a8c22e1cf6437bc82e7fce11a489d0e761
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As there's a single intermediate frame buffer used by both RX and TX
routines, protect operations on it with irq_lock() to avoid possibility
that it will be concurrently modified.
Change-Id: Ibbaf882a15fbb193054dbb13ae848becf9deef3f
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This updates driver for Kinetis SDK Ethernet device (used for example
by BOARD=frdm_k64f) to work with native Zephyr IP stack driver model.
The conversion is done based on the template of eth_enc28j60.c.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Change-Id: Ifb0c7d3f921d663d00a2ded89ecdf2336b6e3783
The register being set before checking the count of the remaining
packets is incorrect, so this code fixes it by setting the proper
register bank before access
Jira: ZEP-1138
Change-Id: Id49ee8439665ff69786f22e13e0d94a2148e4ae7
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
The ENC28J60 hardware module does not support concurrent
transmission and reception.
This fix adds a control semaphore to exclude the execution
of both processes.
Applies the equivalent changes to the legacy driver.
Jira: ZEP-1097
Change-Id: I9602195d5a97f8d4bf652753c284d61f192357fe
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
Tranmission: Consider that fragments are no adjacent.
Reception: Consider receiving data in more than one fragment.
SPI routines: Align SPI fragment size with default buffer fragment
size (128 bytes) for better performance.
Change-Id: I51fc25d8540c36f3719e617a6f33cdea3f63032c
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
Everytime the devices receives a frame with odd length it will
add an extra byte of padding to the reception buffer.
This was causing and issue when receiving frames above 64 bytes
length and with odd length.
This commit pops the extra padding byte everytime the received
frame has an odd length.
The equivalent fix is applied to the legacy driver.
Jira: ZEP-1098
Change-Id: Ib93cbcdcf11f3812961b6702f1b7fa621590aab2
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
When the driver receives or transmits a frames with a length
that is multiple of MAX_BUFFER_LENGTH the last block would be
read/sent twice to spi because a missed calculation on
num_remaining.
The issue is fixed by controling when the remaining bytes are
written/read into the spi device and by setting the spi command
on each spi write/read attempt.
The fix is applied to the legacy driver as well.
Jira: ZEP-1098
Change-Id: Icb2195d74e34dcbcf0c70531da9886ca315bd78b
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
The MAX_BUFFER_LENGTH symbols is now declared in the
eth_ecn28j60_priv.h file.
The legacy driver does not need this declaration here anymore.
Change-Id: I396fe92dbf5679c64183e25fa8b8d342c7f30dae
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
The upper IP stack uses the MAC address to construct the IPv6
address in SLAAC. Because of this the MAC needs to be stored
in big-endian format so that it can be used directly as is.
Change-Id: Ib31da56307017b4284031328772d4cb51d84fa23
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Let's not count the whole buffer length but only the very first frag's.
Up to L2 radio strategy to loop on every fragments and call tx for each.
(once sent, it deletes the fragment, so next fragment is always
buf->frags).
Change-Id: I94130fedfbecffdf62286bcb7f10563c776a255e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The given buffer can come with many fragments, but it's not up to the
hardware driver to send all of these but only the first in the list.
The overall fragments send procedure is handled in l2 level where the
radio transmission strategy loops over the list of framents and send
them one by one relevantly.
Change-Id: Ia7ae42ab4e9f8efb83bf07de6791918059b1e1c9
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As we use STXONCCA, RX will be stopped and reinstated afterwards.
We would be using STXON, since FRMCTRL1_SET_RXENMASK_ON_TX bit is set,
behavior would be the same.
Recalibrating the RX will uselessly abort any received frames before TX
or right after RX got reinstated. So, let's not do that and trust that
RX is anyway properly calibrated after TX.
Change-Id: Iac4fa03a175f8d139c1fc821de01caab1ec86e6b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The fragment count value was incorrectly printed. All
the values > 9 had their last digit chopped off.
Change-Id: I8304b8047baa97995c3927809e4616653c87928b
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This change is related to patch called
"net: Adapt to new behavior of net_buf_frag_add"
This version removes extra net_nbuf_unref() from
the code. The unref was done because net_buf_frag_del()
did not remove the double ref from the list element.
Because of the other patch, the list does not have
double ref any more, so we need to remove the extra
unref in couple of extra places.
Change-Id: If90e01c24b9b4e68afbfa283850d2a1ecb3065ed
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Change DBG to ERR for error cases to get errors when only errors are
selected.
Change-Id: I51fd15900b1efb96d5dff36367afcdf380f11b88
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This prepends logs instead of [general] with [cc2520].
Change-Id: I148159a451981fbe3da638732f0e97900f76bc58
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Slip context parameter is not used in hexdump and in few places
it is not defined. So CONFIG_SLIP_DEBUG=y throws errors.
Change-Id: I73ca26b7d5cd7c3cd532462b5300e25bbdac9511
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
ll_reserve is given through each buffer to be sent, it is therefore easy
to get it from there.
Change-Id: I8b52fe1b72065f5f58275f939253942f7db1f136
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
No need to store the mtu locally as the network interface already holds
it.
Change-Id: I4a1c3d164eefa28622dcb6cd510a66a825c3d9fb
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Link Layer reserved space will be handled by relevant L2 layer.
Change-Id: I8e45119adb4de84ba321cad444c11bedef4415e8
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
LQI is actually not provided as is, but should be computed from an
abstract correlation factor. See Section 20.6.
LQI is provided the same way as Linux does, so it can push it everytime
into the buffer.
Change-Id: I5de318db2c2581d7482cc16e41dc601130753a62
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fixing 80 chars limit by removing length computation:
We can count the FCS as part of the received length, even if AUTOCRC is
on. L2 layer is able to parse this out.
Change-Id: I3c824ed95d177570a07d04784798e14f5979c96b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
L2 RAW channel allows to use some functions of IP stack for RAW access
of network drivers. It is hidden from user and is selected by 2520 raw
driver.
Change-Id: I91dd09803052072dfddb7989d9d67c3a5840f89e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add TI CC2520 driver allowing RAW access to radio interface similar
way Bluetooth user channel works. This makes possible to handle radio
channel inside external 802.15.4 stacks, for example export it over USB
and handle in Linux.
Change-Id: I61bb4c8b998ff1e47dc65427ac471f04ec8fea63
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Source contiki headers only for legacy driver
Change-Id: I356fd65ce9a4ee144c29eed1b51f2f0175315c1c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The bug was introduced by commit ID
a136a2587752cca256950b0efd5567ca29117d11
Which led to write junk as an address into cc2520 and thus made the
chip filtering out all unicast packet (as the incoming address never
matched)
Change-Id: I72009e795039f2059177a5b37a4bcf5d9717d65d
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
As it used directly as the ieee addr.
Propre endianess will have to be solved once this stack will be ported
to other arch than x86.
Change-Id: Ie556fabbd99cc5559025c8392d2f699facb007fa
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
We have no use of configuring cc2520, at built time at least, in
promiscuous mode. So let's get rid of these options for the new driver.
Change-Id: I17611c43bc7ba7961831beaa47cc4e2371f8de61
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This fixes bug setting incorrect long ieee802154 address and also
print address in BE byte order the same way as for Linux.
Change-Id: I774301e992372588dffa6ce5964fb119642a0a0d
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Multipackets support not handled perfectly and breaks regular
flow on some occasions. So remove this support and have to
implement properly.
Change-Id: I1b72c66479c3516df6e6e93998edff1260eb839d
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Print the link layer header in different color so that the
actual IP payload in packets are easier to see. Also the
link layer header of the first packet was not printed.
Change-Id: I99699d378ae28d6d90c683c646c904c926b7dd06
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This driver is used for testing on Qemu where all "radio transmission"
will go through a pipe between 2 Qemus.
Change-Id: I5b4e75de82a98eb730ef9c70b460b4b60c0a60c3
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If no IP stack is seleceted, selecting one of the 2 cc2520 driver will
automatically select the relevant stack.
Change-Id: Icca22da190dc790ce6d302e14c45732f902e02ae
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Or the build will not go through.
Change-Id: I48f5f8661c4100a76e4624ea64d383055327e2a7
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
When only the dummy frame format is enabled, some variables are left
unused, causing some warnings.
Change-Id: Ic7bc5560a9fcb573e715c2cc29f308cec5214f64
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
640 bytes seems too short, raising to 800 bytes.
Change-Id: I8c3418787939369e24fe47c23b0558c36f05af2c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
net_core.h is loading sys_log.h as well, so we need to be
first in order to setup some local definitions.
Change-Id: Ife482bd21e314aa5a5e88433eb8f9a560f9d53a6
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It's basically a copy/paste of original driver,
using native IP stack API.
This is meant to avoid cluttering the original driver
code with #ifdef, and in future it will help removing
the old driver as well.
Change-Id: I67d974ad7440d258583a5c7c6c7160e99210808c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Another driver will be made for native IP stack. This is meant
to avoid cluttering the code with #ifdef all over the place.
Instead driver will be transparently selected at built time.
Change-Id: I283f1194fece9357425b87794b5cb51938ca80d3
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Allocate the right amount of space for L2's context.
Change-Id: Ia2f4f4162334e9e9c26dc95230abdfde5986e052
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
No need to partition the data if MTU is large enough and
data can be sent in one frame.
Change-Id: I8ba0f5030ed1e2c1341c7e2dd409ba636b1a9a4c
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Using macros does not let the compiler verifying about the type we are
providing, which usually give an error easier to understand.
Also, this will let the compiler deciding how to actually optimize
(inline or not) the code.
Change-Id: Iba49590b620ef0a1bd0ed5621453524fcfea747c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If the MTU is bigger than fragment size, we must leave the
fragment link layer header empty so that the received data
count does not get wrong.
Change-Id: I0ed562f39bfbfb559885baa6d774c0383b2228b2
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There is no harm for doing so but debug prints will look
weird in this case.
Change-Id: I48b6953d07a58bc952fe961cf1db846740dadc50
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There will be a crash if network device sends data to network
stack before it is ready to receive such data.
Change-Id: I1a32485faba2972909262c4305fb465b6cb87f07
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The code was using NET_DBG() which is not really available
for the slip/tap driver.
Change-Id: I64cedd5fbfb54fdb80d606cf3199312c8871246f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Easier to see buffer leaks using this variant.
Change-Id: Ibdc8d73133cab4822451104fcd5742e4f1e20e42
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As there is a L2 in the middle, there is no need for
net_if to provide such information.
Change-Id: I58a35d4d124cd8a67026f32e71713ef06f43b7c5
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Net core then does not know anything about l2 related logic.
For instance ARP is used in ethernet l2 API and nowhere else.
This will be helpful when adding different technologies altogether.
Currently, only SLIP driver is enabled to use relevant l2 layer.
Change-Id: I03c93326321028d04222733ca4083e3c6b785202
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
2 warnings happens when CONFIG_SLIP_DEBUG is set, thus fixing it.
Change-Id: I032d7481942e86911764da35cdd6f7b8e05cdeaa
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If CONFIG_SLIP_TAP is defined, then ethernet link layer header is
added before the packet.
Change-Id: I3d266017f85683999d3c67de49b75b60686d7ba7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Renamed net_recv() to net_recv_data() so that the more generic
name can be used by applications. The net_recv_data() is only
meant to be used when L2 layer feeds data into L3 (IP) layer.
Change-Id: Iba155d51f81e3b99964fa916fe87a05a8bf8766a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Check if we have received IPv4 packet and call a handler
function to process it.
Change-Id: I9f9e5f0888d2c3b91401c98f4925647ddce09962
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The SLIP driver is using UART pipe driver to communicate with
host when Zephyr is running in Qemu. Currently this is only
used by networking sub-system when testing the networking
stack.
Change-Id: I432b4136670766a7fc190f146057924c266f9bea
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch refactors the main Kconfig file in order to align it with the
Zephyr code style and to make sure that each Kconfig configuration
portion is easily identifiable.
Change-Id: Ib226aaa9a98e9b08a47d9d1c329f18f4f6936620
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
With the current interface if multiple counters/timers are present in
the system, it is not possible to select from which one to read the
current value.
This patch fixes the behavior.
Change-Id: Id1ae1f2330e98d078f755c0b81c3b176e90b8389
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch refactors the main Kconfig file in order to align it with the
Zephyr code style and to make sure that each Kconfig configuration
portion is easily identifiable.
Change-Id: Iba83be8ae154df4b29ff423b4c3cc97a78c93e00
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The nRF5x series SoCs do not implement systick, hence we disable
CORTEX_M_SYSTICK.
Instead, use nRF SoC Series NRF_RTC1 for system clock interfaces.
The kernel system clock interface is implemented using the low
power real time counter NRF_RTC1. NRF_RTC0 is used by the BLE
controller.
In addition, cleanup nRF5x series defconfig to be consistent.
Jira: ZEP-742
Jira: ZEP-1308
Jira: ZEP-1315
Change-id: I0f6cc1836fe0820a65f2cbb02cf5ae7e9eb92e1d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Make the systick feature optional that can be selected by the SoC.
Change-Id: I4a405640b84daecc17fc1882743d3cafb78ff861
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The reference and polarity fields of the config struct which is passed
to qm_set_config are never cleared, meaning the wrong configuration
may be written if aio_set_config is called for different sets of pins
in the same program.
This patch clears these fields in aio_cmp_disable to prevent such an
issue.
Change-Id: I8feabae1f3d9fa4c7260d94c1ec919ef2fb84bfb
Signed-off-by: James Fagan <james.p.fagan@intel.com>
This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
* Adds static to the containing file scope declarations.
Change-Id: Idaaa0d705a31bc69cdf7e576e303f581d3d0bd5f
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
* Adds static to the containing file scope declarations.
Change-Id: I14651826724c014cc71d62ab6cab03c668c578c0
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
* Adds static to the containing file scope declarations.
Change-Id: I6d48d2eaf6ffd5fa28b37e1d3ca2d467705110f3
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
Change-Id: Ic9e2fd935417fa40127bddeba4660109332087ff
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
* Adds static to the containing file scope declarations.
Change-Id: I03326a800392cffda00b47949981b7e6d119b90f
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Pinmux driver almost certainly should be initialized before the
rest of hardware devices (which may need specific pins already
configured for them), and usually after generic GPIO drivers.
Thus, its priority should be between KERNEL_INIT_PRIORITY_DEFAULT
(default 40) and KERNEL_INIT_PRIORITY_DEVICE (default 50). Thus,
we set PINMUX_INIT_PRIORITY to 45.
There are exceptions to the rule above for particular boards. For
example, BOARD=galileo has GPIO and pinmuxer on I2C bus and thus
overrides PINMUX_INIT_PRIORITY to be much higher. Note that while
PINMUX_INIT_PRIORITY was defined previously (at 60), it was used
only for galileo, which overrides it anyway.
This fix was prompted by investigation why eth_ksdk driver was
non-functional after kernel priorities re-hashing: both eth_ksdk
and pinmux used the same priority, and eth_ksdk happened to run
before pinmux. While bumping eth_ksdk priority would help in the
particular case, the same would likely reoccur with other drivers
like I2C, SPI, etc.
Change-Id: Ie5ca3135c1ee2fe8d9cf48d5c12e62eac63487f7
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Using the K_* macros makes it easier to read what exactly the various
timeouts are.
Change-Id: Ia405d3760b8e600af7e33a7221ef6ec717708973
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This fixes an always false evaluation of the gpio I/O direction
This issue was reported by Coverity
Coverity-CID: 151978
Change-Id: I93ec3319a3f18d564c961a5cbd9dcc9c60efbeb7
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
The GPIO_INT_ACTIVE_LOW value is zero so the mask assignement is
never executed. Using the bit complement GPIO_INT_ACTIVE_HIGH the
proper mask is assigned
This issue was reported by Coverity
Coverity-CID: 151966
Change-Id: Ibc7d2e4c3ebee249b5ab9719f8177cc14c0d1d33
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
The variable type mismatching was caught by LLVM.
Jira: ZEP-1179
Change-Id: If26c881d207a6cedc52b7589c5d7ebb2040c7ab7
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
The enum type mismatching was caught by LLVM.
Jira: ZEP-1179
Change-Id: I50b68e201ef6fb18a02eeda2a2e7548dad3f358c
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This fixes an always false evaluation of the gpio I/O direction
This issue was reported by Coverity (CID 150821).
Change-Id: I6c0e9fe405cbd3e35454a81754fa0b1c721691f0
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
This fixes an always false evaluation of the gpio I/O direction
This issue was reported by Coverity
Coverity-CID: 151833
Change-Id: Ie952d6f50c0383d5631325b69e8e8b234c67c4b8
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
This fixes an always false evaluation of the gpio I/O direction
This issue was reported by Coverity
Coverity-CID: 151834
Change-Id: I033e368b2e91d888f2e8a797490df757513c3906
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
This patch adds the "static" keyword to all the functions that have a
containing file scope.
Change-Id: I0692b389da7f4bf591b5e33f7481bf3dcbbf9801
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the "static" keyword to all the functions that have a
containing file scope.
Change-Id: I28e7daef19359759afb09cd196f659a81c758ea1
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the "static" keyword to all the functions that have a
containing file scope.
Change-Id: I12c29f83e5e8a7eb51880d481da17666764b2c2b
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the "static" keyword to all the functions that have a
containing file scope.
Change-Id: Ib05943b53b6863b5b44848ecb2199b7e99d24139
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
Change-Id: I46a156581cdf79d0ba8f0030ce7b595469db1bcb
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
* Adds static to the gpio_dw_isr declaration.
* Adds guards to the header files.
Change-Id: I1ae70868f0bda97891cbeb494e5efba1bd537aa1
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
Change-Id: I4c8df0999f92a834d4023ce5856a2a6c39797c00
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch removes a redundant "depends on" from the gpio Kconfig for
nRF5X family.
Change-Id: I28ac15b58839e05f47ade81bef66a03a0a44bebd
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch addresses the following issues:
* Aligns the Kconfig code style with Zephyr projects requirements.
* Removes redundant "depends on" from Kconfig.
* Adds static to the gpio_sam3_init declaration.
Change-Id: If5c8a1822d6c116ea34d0f220f3e5fa359b6fa18
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch fixes an unreachable code condition in the uart_console
driver.
If UART_CONSOLE_DEBUG_SERVER_HOOKS was not defined
handled_by_debug_server in console_out was always 0.
This issue was reported by Coverity (CID 131627).
Change-Id: I4376c3e5b3e68220218df6aabd91b6a8900ca31f
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch fixes two "Unchecked return value" conditions into the bma280
driver.
The issue was reported by Coverity (CID 151953).
Change-Id: I2e595b67619411594cec527f358f6c3d3d034550
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This fixes an uninitialized pointer being pass and evaluated by
a subsequent function
This issue was reported by Coverity (CID 150824)
Change-Id: If1f636a44cc675b56e426b1de85895b74ba7105e
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
The variable type mismatching was caught by LLVM.
Jira: ZEP-1179
Change-Id: I1193a946ea5814510e6c07668c5d05a5d91445a8
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This patch fixes unchecked return value conditions in the bme280
driver.
This issue was reported by Coverity (CID 151961, 151959, 151955).
Change-Id: I3a2dfbabd41ae52b00fa512a40e00c2e36c3b5ca
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch fixes a less-than-zero comparison of an unsigned value
condition present in bmi160 driver.
This issue was reported by Coverity (CID 152002, 152003).
Change-Id: I703066519652ac1ecdd9ddf7e97ec7dcbe2a9e27
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Move away from legacy APIs and use unified kenrel instead.
Change-Id: Icae86beec66df1b041405cbe3455913630fc8ad1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use unified kernel APIs and align syntax after function name changes.
Change-Id: I028f4faeaf33e28197d5f705063459188272027d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Switch left-over usage of TICKS_NONE and TICKS_UNLIMITED to the new
unified kernel counterparts K_NO_WAIT and K_FOREVER.
Change-Id: I2f2a16360e816f9f8791eb216deb3c70b8cc87df
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The NBLE driver is now deprecated and will be removed in a future
Zephyr version.
Change-Id: I50753f8cf8566ac1e4e73df480c96253c199e6a7
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There was a lot of duplication between architectures for the definition
of threads and the "nanokernel" guts. These have been consolidated.
Now, a common file kernel/unified/include/kernel_structs.h holds the
common definitions. Architectures provide two files to complement it:
kernel_arch_data.h and kernel_arch_func.h. The first one contains at
least the struct _thread_arch and struct _kernel_arch data structures,
as well as the struct _callee_saved and struct _caller_saved register
layouts. The second file contains anything that needs what is provided
by the common stuff in kernel_structs.h. Those two files are only meant
to be included in kernel_structs.h in very specific locations.
The thread data structure has been separated into three major parts:
common struct _thread_base and struct k_thread, and arch-specific struct
_thread_arch. The first and third ones are included in the second.
The struct s_NANO data structure has been split into two: common struct
_kernel and arch-specific struct _kernel_arch. The latter is included in
the former.
Offsets files have also changed: nano_offsets.h has been renamed
kernel_offsets.h and is still included by the arch-specific offsets.c.
Also, since the thread and kernel data structures are now made of
sub-structures, offsets have to be added to make up the full offset.
Some of these additions have been consolidated in shorter symbols,
available from kernel/unified/include/offsets_short.h, which includes an
arch-specific offsets_arch_short.h. Most of the code include
offsets_short.h now instead of offsets.h.
Change-Id: I084645cb7e6db8db69aeaaf162963fe157045d5a
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Fix compilation error when CONFIG_USB_UART_CONSOLE is not enabled:
drivers/console/uart_console.c: In function 'uart_console_init':
drivers/console/uart_console.c:497:12: error: unused variable 'dtr' [-Werror=unused-variable]
uint32_t dtr = 0;
Change-Id: I592724150f86199f6a57354c3246197db2ac7a01
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add support for console output via the USB UART.
Note that console input via the USB UART doesnt work.
Adds a simulated poll method for UART interface exposed by USB.
Jira : ZEP-775
Change-Id: I357827ea52c027eb000baed80225f422df1f3358
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Add spi flash erase boundary check. The erase boundary must be
4K-aligned. So, the flash chip will round down an non-4K aligned
address to the nearest 4K boundary automatically. As a result of
this, the erase area will start from a different address (if the
API caller specifies an non-4K alighed address), even though the
size of the erased area is the same as what is specified by the
API caller. Let's add a boundary check to make sure the starting
address (from the API caller) is 4K aligned.
Correct an error in the highest address check. Because of the
error, the erase api call will fail if the flash's highest
address byte is involved.
Jira: ZEP-1277 ZEP-1278
Change-Id: I8b6be57cc8f636f94e5fe67d5a492841a8555005
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Add the device_ctrl hook to the ADC driver of the Sensor Subsystem,
using the QMSI APIs to save and restore the driver's context.
Jira: ZEP-667
Change-Id: I8b89a875d8185cc4db3c4bfc30ef0f39c6589df1
Signed-off-by: Iván Briano <ivan.briano@intel.com>
This commit updates the spi_qmsi_ss driver by adding save/restore
context functionality for power management, using the corresponsing
QMSI APIs.
Jira: ZEP-664
Change-Id: I9e62729f91c4808eb557d8a64c0f10955f5456f3
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
This commit updates the i2c_qmsi_ss driver by adding save/restore
context functionality for power management, using the corresponsing
QMSI APIs.
Jira: ZEP-666
Change-Id: I36fb18b52edd4dac4c4b6cb98162adbca74800cb
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
This commit updates the gpio_qmsi_ss driver by adding save/restore
context functionality for power management, using the corresponsing
QMSI APIs.
Jira: ZEP-665
Change-Id: I5d8b6050f5b099678b7e6d9144907ea2ce2dda4b
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
convert all sensor drivers to use threads and the unified kernel API and
remove all legacy APIs.
Change-Id: Ica43ea74ecbbf85273f718f182c413a9dcd8abc6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move both semaphores and nano_work objects to unified kernel APIs.
Change-Id: Icca8a091063544c451e47201cd8e956b95010513
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add driver for CMSDK APB UART ports. The driver implements RX and TX
functionalities. Data transmission is implemented using polling and
interrupts. The driver default configuration for the port is to use
8bit data transmission, 1 stop bit, no parity control.
The driver exposes a public uart driver API and allows to register up
to five UART devices: from 'UART_0' to 'UART_4'. The driver performs
the required pinmux, the clock control configuration is left to the
platform.
The driver has been verified to work with the Hello World sample
application on a Beetle Board.
Jira: ZEP-1245
Change-Id: I5baf78b7659aae2a574d8e66205e6fd5eb579133
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds the support for "runtime" pinmux on ARM V2M Beetle.
The GPIO controllers 2 and 3 are reserved and therefore not exposed
by this driver.
Jira: ZEP-1245
Change-Id: I9637f1a0d2bf6a757e1942160fb170165ffe6a0c
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds the support for the board pinmux initialization on
ARM V2M Beetle.
The GPIO controllers 2 and 3 are reserved and therefore neither exposed
nor configured by this driver.
Jira: ZEP-1245
Change-Id: Id5499c5dd887c319730408eeb30f02eeed1c3699
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The driver is currently used only by the ARM Beetle platform.
Jira: ZEP-1245
Change-Id: I6611edd7486a3c6d82d66a9a96c5d4860dad1539
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This fixes the warnings related to the use of deprecated APIs
converting them to use the unified version.
Change-Id: I76d076de27ecdae4af46abf4baac68e2cc1313c0
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Start using the k_work and k_delayed_work APIs.
Change-Id: Iac0525a444c5c4e0f28db08844d7b28e17e905fc
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Switch to using k_work and k_delayed_work APIs.
Change-Id: I3be18132cc417607adaec0ad711256b94e314c38
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Don't use the deprecated NANOKERNEL init level. The only requirement
for Bluetooth drivers is for them to be registered before the
application main() runs, so POST_KERNEL should be good enough.
Change-Id: I02a8609bf63e9d608b802576214a2e76211b3965
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the unified kernel API k_sleep() instead of the deprecated
fiber_sleep().
Change-Id: I587d72ca5b53aacc02647b32c3ebceb1d7fe067e
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Switch to using the unified kernel k_thread_spawn() API instead of
nano_fiber_start().
Change-Id: I325cf467ae2a52c6aec8fc166397c323929e3013
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the unified kernel API k_yield() instead of fiber_yield().
Change-Id: I8f52031f52f7ac8783033a51751dc22decdfa59a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use defines from k_fifo intead of legacy API.
Change-Id: Ib8cf0d88240ef145da550b8cf83d2580e7140521
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
All boolean options default to 'n' without the need to explicitly
state this. It's only the cases where we want 'default y' where we
need to state this.
Change-Id: I47dbda62462ea437a2423b8508ea2cc640a22e41
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Restructure the Bluetooth options more logically.
- Both host and controller are now behind the same high level
CONFIG_BLUETOOTH.
- Selecting controller support disables other HCI driver selection, so
the controller isn't in the same list as HCI drivers any more.
- Under the top-level there's a "Custom stack" option, which when
enabled opens up the option of choosing CONFIG_NBLE.
There are various other cleanups and simplifications in this patch as
well, since splitting these up would have been fairly tricky while
making sure all test cases still build.
Change-Id: I5bb715cb9d20201cb8b72fbd149c8a09a4b2d7d2
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add Low Power States support to the power shim layer
and show the usage in the quark_se sample.
States are defined as follow:
- SYS_POWER_STATE_CPU_LPS: SS2 with LPSS enabled
- SYS_POWER_STATE_CPU_LPS_1: SS2 with LPSS disabled
- SYS_POWER_STATE_CPU_LPS_2: SS1 with LPSS disabled
Jira: ZEP-994
Change-Id: Ie4b93f6e539cb53fc035be00280b66b2cb0d9fea
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Change the included kernel header file from nanokernel.h to
kernel.h
Change-Id: Ie58174524880ec933191ee1fd46e6c1ba4cd0cc9
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Change the included kernel header file from nanokernel.h
to kernel.h
Change-Id: I754b883d1769517e908e88096e7704666ec12275
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Change the included kernel header file from nanokernel.h
to kernel.h
Change-Id: I76cc952316430d618ea3ecb526d9bc2a99f04cef
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This suppresses warnings for platforms where SERIAL can't be provided.
All the platforms that these drivers are interesting for already
default to SERIAL=y.
Change-Id: Id692f99e018009b30903db8a2c046a6086be01c2
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
USB class drivers may need to offload some work from
upcall interrupt context to a background fiber. This
requires some way to defer taking more data from host
till the offloaded work completes. Two APIs are added to
achieve this.
Further USB class drivers sometimes need to set STALL condition
on end-points to signal errors to host.These too are
added.
Change-Id: Ic973522c3394e23d7f9c4c67affc0cd050afc20f
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Add type cast to prevent overflow.
In the pwm driver function pwm_qmsi_get_cycles_per_sec(),
there is a multiplication which takes ticks_per_us (32 bit
unsigned integer) and USEC_PER_SEC. Practically, overflow
will not happen, since the sys clock is not that high. But,
it can trigger an overflow alarm by automatic tools.
Change-Id: I67e6f6a4763e62f6674fcdd364880d93829e739e
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Add delay to wait for new configuration to take effect before
returning to API caller. It takes time for any change to rtc
configuration to take effect since rtc runs under a much slower
clock.
Of course, we do not have an equation for best wait time.
The value is based on the test results on arduino 101, minfield
and quark se c1000 devboard(some margin added).
Jira: ZEP-991
Change-Id: I0dcee3c5809963dcd418186b85e3473427a4d526
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This KSDK flash shim driver supports the device in the FRDM K64F
platform (enabled with this commit).
WARNING: the driver disables the system interrupts for potentially
long periods of time. This is required to avoid Read-While-Write
issues since most platforms run in XIP mode.
For more detailed information see the link below:
http://cache.freescale.com/files/32bit/doc/app_note/AN4695.pdf
Change-Id: I70f8d09080251033ce2f45be0c2eb95c19fded08
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
It's unused anywhere and unlikely to be in the future.
Change-Id: I57926e91da7d31ef6ddda4f86e6dac103dbfa176
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Update to QMSI 1.3.1 release.
The only build fix needed was due to the split of the I2C ISR on
qm_isr.h .
Change-Id: Ide7a1537572c72981ec3283dc5cf0d543d9ac7d1
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
The uart_k20 serial driver incorrectly assumed that all instances of the
UART peripheral are driven by the system clock, when actually some
instances are driven by the bus clock (which usually runs at half the
system clock). This caused incorrect baud rate calculations for UART
instances driven by the bus clock (UART2-4).
Change-Id: I38041781cdee146912bb5167e7c71d6416b966b5
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
These pins are routed to the arduino header, and configuring them for
UART signals allows us to use the frdm_k64f with a frdm_kw40z shield
board for bluetooth.
Change-Id: Ie30916409844b1dc1c6e1280d5a755a6dc42e418
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Making a reference to the common work queue code should not necessarily
drag in the system workqueue, since it is possible to use a workqueue
that is not the system workqueue. This is done by moving the system
workqueue into its own code module.
Moving the system workqueue to its own code module allows removing the
NANO_WORKQUEUE and SYSTEM_WORKQUEUE kconfig options, and compiling the
common workqueue code and system workqueue all the time. They are only
linked in the final image if a reference to them exist, same as the
other kernel modules.
Change-Id: I6f48d2542bda24f4702e7c2e317818dd082b3c11
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Move controller code from drivers/controller to
subsys/bluetooth/controller.
Change-Id: I73f675188485aa3267507bad7647796e593a3da0
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move the Bluetooth host stack from net/bluetooth to
subsys/bluetooth/host. This is preparation for having both host and
controller under the same root, i.e. subsys/bluetooth/.
Change-Id: I3bc796f7e331fca0c485f3890d62b9c03e027b96
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/hello_world
- samples/philosophers
- samples/drivers/uart
- samples/shell
UARTA0 is currently supported.
Change-Id: I85727c622d4d42183cc9f2f8b43d653e245dd17e
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The shell is not a kernel feature, it is more of a subsystem.
Change-Id: Iaba60b2086ddfe77af427d70b8fc8d06a8bebe14
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add kernel functions to kernel module and make it part
of the shell sample.
Change-Id: If5e8ff8ce7b8edbbb8d62509964700b007eaf88b
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add the definition required to change the pinmux of port H.
Change-Id: I3cc107f9151db4d38fe2cace90cd02d5955a2717
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Some STM32 have more than 32 EXTI lines. Add support for them.
Change-Id: I9a2561664d0d81664acf268bb2257dd99b596a44
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update the suspend and resume hook after changes in QMSI and the resume
from sleep flow.
Change-Id: I14637b5a29b1942740012243fb8217803cf27e9b
Jira: ZEP-1004
Signed-off-by: Iván Briano <ivan.briano@intel.com>
This commit updates the i2c_qmsi driver by removing the temporary Zephyr
save/restore context implementation and using the new QMSI APIs.
Jira: ZEP-996
Change-Id: I9fbd563f214b757f3435037b3e24da4bcf08da14
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
This commit updates the gpio_qmsi driver by removing the temporary
Zephyr save/restore context implementation and using the new QMSI APIs.
Jira: ZEP-999
Change-Id: Ic7b80a8f86baa7a6be11c93bbdebb18a102b0221
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
This commit updates the rtc_qmsi driver by modifying the temporary
Zephyr save/restore context implementation and using the new QMSI APIs.
Jira: ZEP-1000
Change-Id: I6f77fe086ea6415a5bc2b2b21874c8a573fd7b44
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
Signed-off-by: Iván Briano <ivan.briano@intel.com>
This commit updates the spi_qmsi driver by removing the temporary Zephyr
save/restore context implementation and using the new QMSI APIs.
Jira: ZEP-997
Change-Id: I70c6838025253d13d6ebe690ec90dfc1b18bfcea
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
This commit updates the pwm_qmsi driver by removing the temporary Zephyr
save/restore context implementation and using the new QMSI APIs.
Jira: ZEP-1008
Change-Id: Ic92feeb906539f506eb521b7302f8cf5af3edc64
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
Remove the Zephyr implementation and
update the uart_qmsi driver to use new QMSI PM APIs.
Jira: ZEP-998
Change-Id: I418e6384c16e374e9062820e12648a2d524a312d
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
Remove the Zephyr implementation and
update the wdt_qmsi driver to use new QMSI PM APIs.
Jira: ZEP-1001
Change-Id: I4d0a2e3b8cf402b457ee0454650080d406eb6d0a
Signed-off-by: JuanX Solano Menacho <juanx.solano.menacho@intel.com>
For AON peripherals on Quark SE C1000, an API is needed
to retrieve the interrupt status after wake up.
This enables the application to know the wake source before
enabling again the interrupts.
Add this API to the rtc as this is a wake event
on Quark SE C1000.
Jira: ZEP-1188
Change-Id: Id850ce405eb3f4857be720201e462ea8e24a334f
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
For AON peripherals on Quark SE C1000, an API is needed
to retrieve the interrupt status after wake up.
This enables the application to know the wake source before
enabling again the interrupts.
Add this API to the gpio as this is a wake event
on Quark SE C1000.
Jira: ZEP-1188
Change-Id: Icc4aa6617bf18402b7e5dc3aab779ec2964e1c5b
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
For AON peripherals on Quark SE C1000, an API is needed
to retrieve the interrupt status after wake up.
This enables the application to know the wake source before
enabling again the interrupts.
Add this API to the aio comparator as this is a wake event
on Quark SE C1000.
Jira: ZEP-1188
Change-Id: Ifa08353270910a363c15a4203770ff3e7857572b
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
For AON peripherals on Quark SE C1000, an API is needed
to retrieve the interrupt status after wake up.
This enables the application to know the wake source before
enabling again the interrupts.
Add this API to the periodic timer as this is a wake event
on Quark SE C1000.
Jira: ZEP-1188
Change-Id: I79976230bccb1f970b6856d28bf7428175167828
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
In ST CMSIS files, FLASH_BASE does not mean base address of FLASH register
Instead FLASH_R_BASE is used.
stm32f1 clock control driver is updated to be compatible with this naming.
Change-Id: Ic4fb49c60c392e15fd12c69266baf4c686bd343b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
There is no need for copying command string to temporary variable on
the stack.
Change-Id: I41fd2582600908ac523b87c83a426eef27d1c454
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
This fix commands tab completion and make it similar to Linux shell
completion:
- single match complets command and add space at the end
- multi match lists matched commands and complete common part
- no match does nothing
Change-Id: Ib2d90889c79e8d35a78b8847d2b9e124cdc00a6c
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Add the necessary infrstructure to support power management for the
QMSI Flash driver. If deep sleep is supported, this driver supports
saving its context to be restored on resume.
Jira: ZEP-1006
Change-Id: Ied88e86d13ef9e4e62bd6ac9d8454d9a9a3d2962
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Add the necessary infrastructure to support power management for the
QMSI DMA driver. If deep sleep is supported, this driver supports
saving its context to be restored on resume.
Jira: ZEP-1005
Change-Id: I49f1f985eb0f250c777c6950178715fb794db537
Signed-off-by: Iván Briano <ivan.briano@intel.com>
The GPIO and AON GPIO ports are available to both the x86 and ARC
cores, but the driver always assumed only the x86 at the time of
configuring interrupts.
Use the available macros to set the correct values independently of
which core it's being built for.
Jira: ZEP-1030
Change-Id: I310afcc48780fbe1cac9dc3368a6de11bd797fda
Signed-off-by: Iván Briano <ivan.briano@intel.com>
The SoC level peripherals are accesible by both cores, while the SS
ones are only available to the sensor subsystem. Since the ARC core can
make use of both drivers at the same time, we need to be able to
differentiate their configuration values somehow.
Also disable the SoC GPIO for the ARC by default, as it still needs
more changes to be usable.
Jira: ZEP-1030
Change-Id: Ic5415c404ecd32a3e560467b6f5eaa873a515d72
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Use the macros provided by QMSI (or by ourselves, when QMSI doesn't
have them yet) to register interrupts independently of which core it's
building for.
Change-Id: I83fd7e42598b45aef8132316906a3bff291dfe92
Signed-off-by: Iván Briano <ivan.briano@intel.com>
The callback from the QMSI driver now can take a data pointer to pass
to the given function, so use that to pass the device to our callback
instead of defining one function for each supported port.
Change-Id: I82d863314e0443b7c4a12d4a9ad763b9634ca8e2
Signed-off-by: Iván Briano <ivan.briano@intel.com>
If application prompt handler returns NULL curently selected module
prompt should also be checked before of printing default shell prompt.
Change-Id: Iba9c191041951c31036766b1cc8070b040655445
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Ability to use Zephyr shell by multiple modules simultaneously, each
module for its own usage.
Old shell implementation enabled the user to call only one module
commands, not all of the modules simultaneously.
Change-Id: I0ef8fa2fd190b7490c44fe91d1016363258302c9
Signed-off-by: Yael Avramovich <yael.avramovich@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In the unified kernel legacy layer, both these functions are
implemented as #defines which can't be put in a struct.
Eventually this driver should be updated to use new APIs, but
this will get it to at least build which is the priority.
Change-Id: Ic5dfb5b85ff3bd0d1646f542340642549a2b2e05
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This allows to delete character after cursor.
Change-Id: I9acc5e1edeb688ea4ec36e91aef69ecb5f5f6354
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
This allows to navigate to begining and end of the line easily.
Change-Id: I3a839a0499961d55574a310c65811dd2fe048703
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
In 3 of our UART driver implementations the ISR is exclusively
used and enabled for the RX path. The existing logic was
susceptible to a stall situation where a polled out transmission
would be interrupted by a reception and then the ISR code
would loop forever due to the TX event being signalled (although
the interrupt itself was disabled) causing the ISR to keep
looping for an RX interrupt.
Change-Id: Ic379e58b1c974aca3cee37d2d81f12c3726fb160
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
These options were only needed for a MyNewt-based nRF51 firmware on
these boards (the MyNewt BLE stack is called Nimble, hence the
prj_nimble.conf sample config files). With a Zephyr-based nRF51
firmware these options are no-longer needed, so it's not appropriate
to have them default to enabled. Instead, if they are needed, require
the app-specific configuration to enable them.
Change-Id: Iefbee4d97590af4e11bcedea05fe61f32a147b83
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
qm_interrupt.h is not needed.
Change-Id: Ia9e62db9fc39ee7a8a36e087eb447cbc4a419817
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Implement qmsi shim driver based on the new API interfaces.
Recently, a RFC was sent and discussed on the re-design of
PWM interfaces. A API change was already posted.
The API new design will deprecate all existing APIs and three
new APIs will be added. The new APIs are pwm_pin_set_cycles,
pwm_pin_set_usec and pwm_get_cycles_per_sec. Pwm_pin_set_cycles
and pwm_pin_set_usec will rely on two driver functions to set
the period and pulse width. This change is to implement the
driver functions pwm_qmsi_pin_set and pwm_qmsi_get_cycles_per_
sec.
Jira: ZEP-745
Change-Id: I39bb973f8c5b19cb7dbd496d10e7f0b6735efc12
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Update the QMSI drop we maintain in Zephyr, and fix the build where
needed:
- QM_SCSS_INT is renamed to QM_INTERRUPT_ROUTER;
- every member of QM_INTERRUPT_ROUTER was renamed as well;
- QM_IRQ_* renamed too, mostly added _INT at the end;
- some isr functions were renamed to keep their names consistent;
- build for x86 needs to define QM_LAKEMONT, as QM_SENSOR was for ARC.
Change-Id: I459029ca0d373f6c831e2bb8ebd52402a55994d1
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Add support for the STM32F401 chip on the board
Change-Id: I96c0799f3658ecea096fa5971bce9faf21919ee1
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change the clock accessors to a tuple of bus ID of the subsystem and enable
bits for the device - it is clearer to read than the opaque pointers.
Change-Id: I9ae73c222c04adac4cf2bc06e97f4ec199bdac3c
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
STM32F401 allows for upto 16 alternate functions on each pin.
Change-Id: Ib1c14fd31abaa2b05a5ab0f7bd1b4a4748f10f84
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implements MCU-specific GPIO input interrupt integration. Added
definition of System configuration controller as well as its needed by
the GPIO code.
The SYSCFG controller is used for system-specific configuration such as:
- remap the type of memory accessible at address 0x00000000
- manage the external interrupt line connection to GPIOs
- configure the I/O compensation cell
Change-Id: Id2ebfbd1b21e77be76406d1cd6cd5d4989e9e2fa
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Based on the STM32F10x driver. Removing old code as we need to use the
bus number when dealing with 4 possible peripherals.
Change-Id: Id0263aa008e9b039ff9a00339e5622e289ffdf99
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds support for the STMicroelectronics STM32F4x family in the
STM32 MCU line. Configuration is included for the STM32F401RE MCU.
Acknowledgements to Pawel Wodnicki's earlier submission from February that
was used as a starting point for this port. In the end, we rewrote all of it.
Change-Id: I9797c282ac3c0cc66a63b9d34821de95df537ef6
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
The correct layout for help text is <TAB><SPACE><SPACE>.
Change-Id: Ief4167e75709e358089f701041ac06386351f423
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Fix issues with tab vs space as well as missing license/copyright
header in hci/Kconfig.
Change-Id: Id766308dc8eda2d598ea749e5e0d2166014db929
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bt_driver API was created when Zephyr only had a Bluetooth host
stack, but no controller-side functionality. The only "driver" that
was needed for the host was the HCI driver, and hence "HCI" was
omitted from the name.
With support both for host and controller Zephyr will be getting more
Bluetooth driver types, in particular radio drivers. To prepare for
this, move all HCI drivers to drivers/bluetooth/hci/ and rename the
bt_driver API bt_hci_driver.
Change-Id: I82829da80aa61f26c2bb2005380f1e88d069ac7d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since RSSI events trigger interrupts and signal the RX path
semaphore with a resulting event lenght of 0. Due to this
fact the Controller HCI driver was leaking (i.e. not freeing)
those events, grinding the recv_fiber to a halt.
Issue identified by Szymon Janc.
Change-Id: I3e259b2823717b523ac331f8f787252414fb9290
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Report the HCI version supported by the Controller as 4.2,
since it was set as 0 (1.0b) and this confused certain Host
implementations, such as BlueZ.
Change-Id: I809721ee9c2b55e77e6a3ca63688c802a9ffa0ba
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The grove sensors use the sensor interface, so make them depend
on it just like the other sensors.
Change-Id: I9b62a3fa26f54dd683c65ca154c1af7c7c92772f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Set DMA transfer to QM_DMA_TYPE_SINGLE for all channels.
This keeps the previous behavior as of QMSI 1.1.
In the future, we may consider adding support for using other DMA
transfer types. This, however, will demand adding new API to Zephyr's
dma.h .
Change-Id: I8071555190662a72279069ff9fce3d4b9e861629
Signed-off-by: Maciej Kuc <maciejx.kuc@intel.com>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
STM32F4 requires the alternative function config to be set, so just
initialize that as part of the gpio configure call.
Change-Id: I33a4a8efec59c5ebe7dc3f3580f0dd2bf7ded7f4
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Adds basic sensor driver support for the NXP FXOS8700 6-axis
accelerometer/magnetometer. Currently this driver supports
accelerometer-only, magnetometer-only, and hybrid (accelerometer +
magnetometer) modes, as well as 2g, 4g, and 8g accelerometer full scale
ranges.
This driver does not yet support any sensor triggers such as the data
ready trigger, or runtime changing of sensor attributes.
Datasheet:
http://cache.nxp.com/files/sensors/doc/data_sheet/FXOS8700CQ.pdf
Origin: Original
Jira: ZEP-721
Change-Id: Iff0f751c737196f60d5c5d3448631b57093ece34
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Change-Id: I6e3c7e4e420d9b9c55bbb49cf6f13b6e09ec4bb7
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Correct the text of the SYS_CLOCK_TICKS_PER_SEC #error diagnostic to
reflect the actual logic of the gate.
Change-Id: I28ad324b0b246e4a8de29b64483a97577a1b6fb7
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The config variable WDT_0_IRQ_PRI is intended to be generic across a
range of watchdog drivers, however it has no default value which means
that if CONFIG_WATCHDOG is enabled, but no driver is provided for a
specific board the the configuration will fail. For now, make
WDT_0_IRQ_PRI depend on the only driver that uses it.
Change-Id: I54708d66ac8fbc2ef657a1ef4510eb5e7a2cff28
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The Ready To Send (RTS) hardware flow control signal in the nRF5
UART was being configured as an output with a pull-up on it.
This was seemingly causing certain issues with btattach on Linux
and it's not done anywhere else.
Change-Id: Id792d967b043ea7a796d6598500a733c092dbc2c
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The various other KSDK shim drivers follow the name pattern
<DEVICE>_KSDK, renaming the RANDOM driver to follow the pattern.
Change-Id: I89409083f94c0990129726e70a964b02e0dc2802
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The baudrate calculation present in set_baudrate() is
causing the UART to emit inital bytes incorrectly, for a
reason currently unknown, but directly related to the fact
that __aeabi_uldivmod is being invoked.
Since the nRF5x Product Specifications do not provide a
standard formula to calculate baudrates and instead list
a predefined set of divisor values, we opt here to use the
official values and remove the attempt at calculating them
manually.
Change-Id: Ic3ff42ea6d065e9a1d26a5350ce5bf5ad661160a
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When user wants to set all the PWM ports in one call,
pwm_qmsi_set_values() should call __set_one_port() for
each PWM port. The current pwm_qmsi_set_values() will
return after setting the first PWM port. It's illogical.
Change-Id: I5776bf636c2dc58683c629e26f72fca335e781db
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
This refactor is in preparation for making driver API structures
const.
The console driver provides a mechanism to install an input and an
output hook function. These are primarily used by the onboard
gdb-server. The output hook is entirely implemented within the
console driver.
The input hook is partially implemented in the top of the uart driver
and within the console driver. The hook function itself is installed
in the uart API structure, but is invoked only by the console driver.
Installing the hook function directly into the uart API structure
prevents the API structure being const. There are two approaches to
fixing this:
1) Implement setting of the input hook in the same way as
uart_irq_callback_set().
2) Move the input hook entirely to the console driver.
We implement the latter. This approach has two benefits, first it
removes the need for every uart driver to implement the behaviour and
second, the current placement of the callback function in the uart API
seems odd given that the callback is only invoked by the console
driver, never by a uart driver.
Change-Id: I258b312d3055df1c2bdeb896bd4f4f39c40838f7
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The variable is defined as SYS_LOG_GROVE_LEVEL in Kconfig..
Change-Id: I0f77336df2293694ece71f4f5fccb5283f6dc58c
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The name read16() collides with other definitions within Zephyr. We
don't actually use this function here, so remove the definition. Fix
various other unnecessary name exports while we are here by adding
'static'.
Change-Id: I7eee8c527a62fea4e6e1bdae8a4874d8ce66596c
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The read16() name collides with other definitions within zephyr. Make
it static and fix a few other unnecessary name exports while we are
here.
Change-Id: Id72d44a6b84b8d72c7ba2d0f34b29dbc1d02f2b6
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The exact pin numbers for the nRF5 UART configuration is
board-specific, so the Kconfig default values should be in a
board-specific file.
Change-Id: Ibaacde292db191221e32b3626c68bf972dd26016
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to avoid type conflicts make sure that ISR_HANDLED
is defined. This makes the ISR the correct type.
Make sure that the pointer for the unused argument for ISR
is of the proper type (NULL).
Change-Id: Ia1873f32d2e2174085f929e318a780a1b2574785
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Make default value compatible with both nRF51 and nRF52.
Change-Id: I65dafbdf8518103becdd7388e9c0195ef1c4460d
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Default IRQ priority changed to 1 to so it can also be compatible with
nRF51 (Cortex-M0 allows up to 4 priority levels but Zephyr needs the
first two for the OS).
Change-Id: Ie57a729f5d932f020a7d1d7e55cf3741f1ecfbab
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Integrating the IRQ definitions for both nRF51 and nRF52, and defining
the set of IRQ values that are common to both.
Also switch the controller, uart and clock drivers to use the common
header definitions.
Change-Id: Id6816d7a97720896cfe4df83656fb8b1f8fb01fa
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
It's not FMSTAT<0/1> but FSMSTAT<0/1>
Change-Id: I836cf001b7baefe86df67f13a8759ea4e697a28e
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Put the clk_perih_enable() call outside of the switch statement so it
actually runs.
Jira: ZEP-1048
Change-Id: Iee8efb4430d37dc74ce48f249bbf58d53125b520
Signed-off-by: Iván Briano <ivan.briano@intel.com>
As part of an effort to closely integrate with Zephyr OS,
removed the custom implementation of clock control
interfaces used in controller code and use the driver model
in Zephyr OS.
Jira: ZEP-897
Change-id: I03efbff471e42b9bd9832818dd20dd5998a60227
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
This way the application can reuse the same callback for multiple CCC
since it can track what CCC is affect by checking the attribute pointer.
Change-Id: I608da643aea07de26b65d67e6db3268d717d0f53
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
nRF51x SoC is based on ARM Cortex-M0 and running at 16MHz clock.
Due to Radio ISR latency restriction, the CPU utilization within
BLE tIFS of 150 us should not be more than the time radio h/w
takes to get ready. In order to keep short CPU utilization
inside tIFS encryption procedure has been spread over several
connection intervals. In comparison to possible encryption setup
in 3 connection intervals, this commit introduces a encryption
setup being done in 5 connection intervals so that max. CPU time
is well within the permissible limits by nRF51 h/w and tIFS.
Change-Id: I8971d69675836b9e18bea59d95951e0dfe8a7d2d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Move to utilizing an inline function for getting the base addr of the
external interrupt register region. This is in prep for support more
than 32 external interrupts.
Change-Id: Ifdaad67703068395a7749543ef68435435e7c9ba
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The HDC1008_I2C_ADDR config option should be available only if HDC1008
is enabled.
Change-Id: I0d1813512396faefb609527ba5df2a0c4ea159a9
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Change e4b89571aa renamed the variable
to an undeclared one, without breaking verify but daly breaks.
A local variable of type spi_intel_data was missing on this
function.
Jira: ZEP-1095
Change-Id: Ie410933c2472378d4a6f24d6ca932ac203e3b08c
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Mutable driver state relocated from config_info to driver_info.
This driver is unused by any board, nor can it be compiled for any
board. Hence this patch reflects the mechanical change that should be
made to the driver in order to support a const config_info, but the
patch has been neither compiled, nor tested.
Change-Id: I28597962e81d6e02f1f4befe48c3a3324691cfeb
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Mutable driver state relocated from config_info to driver_info. This
driver supports PCI enumeration. We drop code that attempts to update
irq_num based on PCI enumeration because the interrupt found by PCI
enumeration must always be the same as the statically configured IRQ
number.
Change-Id: I5580b0ba95635696a825fe66dbf16259c54d5ba8
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
PCI enumeration modifies pci_dev and base_addr at driver
initialization therefore these objects move from config_info to
driver_data in preparation for config_info becoming const.
We drop code that attempts to update irq_num based on PCI enumeration
because the interrupt found by PCI enumeration must always be the same
as the statically configured IRQ number.
Change-Id: Ibfefa851d2836d524b8151ed0108ecf9de2cd3a3
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
PCI enumeration modifies pci_dev, base_addaress at driver
initialization therefore this objects move from config_info to
driver_data in preparation for config_info becoming const..
We drop code that attempts to update irq_num based on PCI enumeration
because the interrupt found by PCI enumeration must always be the same
as the statically configured IRQ number.
Change-Id: Id5af682dac112ec6dc6e4aa14b655e0047972d38
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Mutable driver state relocated from config_info to driver_info. This
driver supports PCI enumeration. We drop code that attempts to update
irq_num based on PCI enumeration because the interrupt found by PCI
enumeration must always be the same as the statically configured IRQ
number.
Change-Id: I97198ae9603505606a872b07824d6c61688f0ced
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Pending bit gets cleared by writing 1 into it, so don't use the previous
value and just write the line bit offset instead.
Change-Id: I4c88016bf53327b2670a144d3b994945f26fc002
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>¬
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Since dd5e90ec the device_get_binding call returns NULL unless the
driver_api is set by the driver. Since the exti driver only uses an
internal struct to store the callbacks, remove the need for the device
binding call from other drivers (e.g. gpio).
Change-Id: If0b733c27754108118d87ef02640311f0535ab57
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
The field is "NF: Noise detect flag". Given that every other field name is
faithful to the manual, do the same for NF.
Change-Id: I300663e6d5016bf28071d2a1926ec73682ae3d01
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
In QMSI 1.2 API, the RTC divider value for the prescaler can now be set
on runtime. This is done through a config parameter for the qm_rtc
driver.
Fix the rtc shim driver by using the value defined in rtc.h as
RTC_DIVIDER.
Change-Id: I5ab61a5a1a3debca103f2782e0ac584938dc91e1
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Update the QMSI drop we maintain in Zephyr, and fix the build where
needed:
- QM_USB_BASE is renamed to QM_USB_0_BASE;
- parameter int_en from qm_uart cfg struct was removed;
- driver's folder now has a new structure, fix makefiles accordingly;
- QM_WDT_MODE and related renamed to QM_WDT_CR_RMOD;
- QM_SCSS_AON renamed to QM_AONC.
Change-Id: Iffe9c66b7a3f2fe64418326e20ff0894149b3044
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
The hexiwear board has a k64 SoC, so we can reuse the k64 pinmux driver
and just add a new pinmux table for the board.
Jira: ZEP-716
Change-Id: I936691b3578db298014f44fe18433d7943b431f3
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The k64 pinmux driver can be used for any k64 board, not just frdm_k64f,
therefore renaming the driver accordingly.
Change-Id: I45e96d4a5ff6aa859d0f57fe098e44a8ae5283d1
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Those options are not being used anywhere, so remove them and avoid some
confusion.
Change-Id: Ia3767dbd2432851dfae4b1e996f02ed1b2450505
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The Atmel SAM3 serial driver poll in function checked
for new characters incorrectly.
Change-Id: I9024a991404bf949226634c9f6c6ea507577cff1
Signed-off-by: Justin Watson <jwatson5@gmail.com>
In the Nordic Semiconductor's nRF5x series SoC clock control
system can source the system clocks from a range of internal or
external high and low frequency oscillators and distribute them
to modules based upon a module’s individual requirements.
In this commit the implementation adds support for 16MHz
peripheral clock, 32.768 kHz RC oscillator, and 32.768 kHz
crystal oscillator clock sources.
16MHz peripheral clock is required to use the 2.4GHz Radio
peripheral. 32.768 kHz RC or crystal oscillator clock source
is required to use the real time counter peripheral.
Jira: ZEP-896
Change-id: I1a1e22322a5a26b587f3e27bb979e6296987ac1c
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Provide a network driver wrapped around the KSDK ENET and PHY
drivers.
The driver performs one shot PHY setup. There is no support for PHY
disconnect, reconnect or configuration change. The PHY setup,
implement via KSDK contains polled code that can block the
initialization thread for a few seconds.
There is no statistics collection for either normal operation or error
behaviour.
Origin: Original
Change-Id: Ia0f2e89a61348ed949976070353e823c178fcb24
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The bt_storage_clear() function doesn't modify the data behind the
addr parameter, so the pointer should be decared const.
Change-Id: Icce676f9df80bac26ba4877bb63752559a43339f
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
PCI enumeration modifies pci_dev and port at driver initialization,
these objects move from config_info to driver_data in preparation for
config_info becoming const.
This driver shares a unified uart configuration structure with other
uart device drivers. The structure uses 'union' and the preprocessor
to customize the structure to the drivers specific requirement. There
appears to be no compelling reason why all the uart drivers should
share the same (customized) config_info structure. In order to
re-organize the structure for this driver to get config_info const, an
ns16550 specific config structure is defined and the driver switched
over from the generic uart_config.
Change-Id: I31932d811f623a9370b69903114ae97b15d65886
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Move the RW channel_period object from the driver config structure to
the driver context. Remove the now empty driver config structure.
Change-Id: I38df7877f1bfb9bb55bcd61e7f35cebb6e4916bd
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The callback list within the driver config is updated dynamically
hence the list itself cannot be const. Create a runtime context
driver data structure and relocate the callback list to the new
structure.
Change-Id: Ied20846e6a78e43967239afa7797456a9abd8548
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
