Add support for U(S)ART 4 to 10 that can be found at least on some
members of the STM32F4 family.
Change-Id: Ie870492511f885005cf023040e498bd4d800e807
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The registration of each serial port differs only by a few details.
These differences can be factorized in order to create a generic
registration macro.
This has several advantages:
- Less code
- Easier to add new ports
- Less work to add support for new STM32 families
Change-Id: I6e62a96ccbbf03c9d51bc2617db6a851ff0d83c7
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Add necessary board files, pinmux and device tree in order to have a
usable debug console.
Origin: Original
Change-Id: I280320700352fd36a544c03f4e57d2eeec2449e5
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The RX pin should be PA15 to use the Virtual COM port of the ST-LINK.
Also adds the missing entry in pinmux_stm32l4x.h.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
During introduction of LL clock_control driver on stm32f4 series,
AHB2 clock activation/deactivation case was let under stm32l4 condition
preventing activation of this clock with F4 series.
This patch fixes the issue.
Change-Id: I5e488e990d33252f491f8960fc7a798ca3416be2
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
uart_irq_tx_empty() function proved to be problematic: its semantics
was not documented properly, and many hardware uses terminology like
"TX register empty" to signify condition of TX register being ready
to accept another character (what in Zephyr is tested with
uart_irq_tx_ready()). To avoid confusion, uart_irq_tx_empty() was
renamed to uart_irq_tx_complete(), propagating to drivers/serial
device methods.
The semantics and usage model of all of uart_irq_rx_ready(),
uart_irq_tx_ready(), uart_irq_tx_complete() is now described in
detail.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Since more and more code is going to be reused by both the Host and the
Controller, this commit introduces a common/ folder that will contain
everything that is not tied to one of the two components but shared by
them.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
XT_* macros are defined in xtensa HAL headers as xcc intrinsics. gcc
does not have any of these intrinsics. Replace XT_* macros with inline
assembly or provide gcc-compatible definitions.
Change-Id: If823ea8a7898a11a3a8363b17efdba27dee4c6a4
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Commit 58c8d15 ("clock control:stm32: provide STM32Cube LL based
driver") added PLL initialization which disables the PLL before
configuring it.
This works if the system clock source is not the PLL (which is the
usual case for Zephyr booting out of chip reset). However, if the
SYSCLK source *is* the PLL, this halts execution.
To support this use case, switch the SYSCLK source to the
always-present HSI before disabling the PLL.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Factor out a subroutine used to switch SYSCLK to HSI. This code will
be used again in a subsequent patch.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Since the HCI driver debug option applies to both files in
drivers/bluetooth and subsys/bluetooth, the configuration option itself
now lives in the top-level Kconfig file for consistency.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
fix misspelling in Kconfig files that would show up in configuration
documentation and screens.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
There is no need to unmask/mask the global transceiver interrupt
in kw41z_start/stop as the radio interrupt line is enabled/disabled
anyway with irq_enable/disable calls.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
- set state to IDLE if TMR1 expires, but CCA reports channel as free
- no need to check for CCABFRTX, as the hardware isn't setup to do
CCA before TX
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Sequence timeouts should be scaled to 16us, as TMR_PRESCALE was set
to 62.5kHz.
Also, radio warmup times and TX packet length need to be taken into
account.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
The main difference to how the previous driver operates, is that this
version has zero-copy transmission. The transmit DMA descriptor is
updated for every fragment that is transmitted from the driver.
Another difference in the transmission path is that this version won't
spin indefinitely while waiting for the DMA transfer to complete; an
arbitrary number of busy checks (20) will be performed, and then
the transmission thread will yield for as long as necessary to finish
the transfer.
These two changes should fix ZEP-472; since that issue was opened for
an older version of Zephyr with uIP, I did not bother going all the way
back to test.
This has been only tested with a Galileo board, using Shared IRQ.
Jira: ZEP-1652
Jira: ZEP-472
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The purpose of irq_update() is to cache value of UART IRQ status
register for devices which needs such caching. No other driver
performs any other side effects in this call. For STM32, clearing
TC (tx complete) bit was introduced in 8c079e91c9
which is otherwise titled as a conversion to STM32Cube HAL. Thus,
there does not seem to be specific reasons why this code was added.
On the other hand, it leads to behaviorial artifacts when dealing
with interrup-driven UART code (specific issue seen was delaying
of transmitting every other character).
Change-Id: Id20bf214b36eeb6c09e29cc2e6bfca4f7221a1a4
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
* lis2dh 3 axis accelerometer support on SPI and I2C bus
* data ready and anymotion type of trigger support
Tested on Dynastream module D52QD2M4IA-A using SPI
Origin: based on Zephyr lis3dh driver
Change-Id: I2c4e9418b87f09c957bba8f73522bd78830bc809
Signed-off-by: Roger Lendenmann <roger.lendenmann@intel.com>
The files for the Arduino Due needed to be updated to use the new
configuration when the SoC moved from the atmel_sam3 directory to
the atmel_sam/sam3x directory.
Jira: ZEP-2067
Signed-off-by: Justin Watson <jwatson5@gmail.com>
SBCon is a simple device which allows directly setting and getting the
hardware state of two-bit serial interfaces like I2C. Therefore to be
useable we need to drive the lines with the appropriate protocol under
software control.
Change-Id: If9000bb75f7b0ad7bbb256b1cb38cc70fa6ca8ea
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Several minor changes to clean up I2C Kconfig file
- align help text
- remove duplicate dependencies
- use unified naming for I2C port options
- replace outdated references to datasheet in help text
- add comments at the end of 'endif'
Change-Id: I452083feb29f40909e6e38324ff9d9961fc6bd07
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The switch from C99 integer types to u16_t, etc. caused misalignment
in structs and function definitions with multi-line parameter lists.
Change-Id: Ic0e33dc199f834ad7772417bca4c0b2d2f779d15
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With recent changes we now have both SAME70 and SAM3X under
SOC_FAMILY_SAM so we need to limit the watchdog driver only to SAME70 as
it only builds there right now.
Change-Id: I4a7c90247ad22532b2384ca536cfb0cbd65186f9
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Converted Stellaris UART driver over to utilize device tree generated
defines. Added a yaml description for the uart, and converted over the
ti_lm3s6965 SoC & qemu_cortex_m3 board port over to utilize it.
Change-Id: Ie20844eb63d2c68eb59ad4160f7f5b5a35e2943b
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There isn't any reason to export the uart_stellaris_isr function, so
lets make it static and remove the associated header file.
Change-Id: I3a131b584d9d6fb6279a1503512668a71510dd4d
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This driver implements an I2C interface by driving two GPIO lines under
software control.
Change-Id: Ie49cc67aed6acb30086ee851041fe2470da241cf
Signed-off-by: Jon Medhurst <tixy@linaro.org>
This library implements the I2C single master protocol in software.
It supports the Standard-mode and Fast-mode speeds and doesn't support
optional protocol feature like 10-bit addresses or clock stretching.
Change-Id: I375d572a83714522421f2967dc414b3bec169e95
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Clean-up the pinmux header as a preparatory work before adding more
pinmuxes.
This is achieved by the following two actions:
- Reorder the defines by increasing GPIO order to make it
easier to add more pinmux over time while avoiding a huge mess
- Use tabs to align
Change-Id: I07d9ae28f61287748d33dcf638dcbf2e6865517b
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
This commit provides support for disco_l475_iot1 board
Pinmux driver is provided with initial support definitions
Change-Id: I17b637a8ba0b033014969eca8fffe76319c47c52
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adds a shim layer around the mcux lpsci driver to adapt it to the Zephyr
serial interface.
Change-Id: I024f1605e3194f34bb57e8a121900e05b3085a82
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commits align CONFIG_ factor names between stm32f4 and stm32l4
series to enable code factorization such as use of Q_DIVISOR.
Though, it does not concatenate kconfig sections as we might use
a bit of time to see what is needed in this regard
Change-Id: Ia603406d53949abf5675b801a5448397d5ab8462
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Small code refactorisation in order to ease up coming
support of stm32f1 series by stm32 commom clock control
driver
Change-Id: I486cfba137cd048d65f0732e10aa29d877bb03e5
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following activation of stm32 common clock driver for stm32f4 series
remove references to stm32f4 specific driver.
Change-Id: I372a0ea046007bcb34944d6b2b8880077583b1d3
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following update of LL clock driver to suport F4 series,
update dma driver to support LL clock driver API.
Change-Id: Ic8ecfe4f33109204f3b5f8c22bcb9c41de81531d
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit enables STM32Cube LL based driver for stm32f4 series.
This generic driver provides a unified API to clock driver for all
stm32 series.
LL API allows driver to be lightweight and to keep genericity across
stm32 family to ease further devlopment and maintenance.
Change-Id: Ie31ae8f433313787f9c9eda77de41925721d54dd
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Devicetree.org specifies that serial devices property used to set
baud rate is "current-speed", while zephyr uses "baud-rate".
Align property name in order to keep zephyr dts files compatible
with device tree specification and could be re-used from/to
Linux for instance. We also cleanup a few SoCs that set "baud-rate" in
the SoC dts and not the board.
Jira: ZEP-2048
Change-Id: I097e7439ee46fe77c628b56531772950382fafcc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The data fragments were stored in reversed order when the RX
data was saved into network buffers. This was caused by net_pkt
changes in commit "net/net_pkt: Fully separate struct net_pkt
from struct net_buf".
Change-Id: I8ad2cfc23b2cb90896b0548eab168895b0d7421d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For stream-based protocols (TCP), adding less data than requested
("short write") is generally not a problem - the rest of data can
be sent in the next packet. So, make net_pkt_append() return length
of written data instead of just bool flag, which makes it closer
to the behavior of POSIX send()/write() calls.
There're many users of older net_pkt_append() in the codebase
however, so net_pkt_append_all() convenience function is added which
keeps returning a boolean flag. All current users were converted to
this function, except for two:
samples/net/http_server/src/ssl_utils.c
samples/net/mbedtls_sslclient/src/tcp.c
Both are related to TLS and implement mbedTLS "tx callback", which
follows POSIX short-write semantics. Both cases also had a code to
workaround previous boolean-only behavior of net_pkt_append() - after
calling it, they measured length of the actual data added (but only
in case of successful return of net_pkt_append(), so that didn't
really help). So, these 2 cases are already improved.
Jira: ZEP-1984
Change-Id: Ibaf7c029b15e91b516d73dab3612eed190ee982b
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This patch adds support for reading MAC address from I2C EEPROM.
Only chips with 7-bit I2C device address are supported.
Change-Id: Ibedc33e54e33bdb901840e104063e2f4752b9123
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Otherwise they are send as is and stripped by tunslip6, resulting in
malformed packets.
Jira: ZEP-2037
Change-Id: I1267b9ac956f3cd7aa3456ce20447ef97281d7a8
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
Don't busy-wait in uart_stm32_fifo_fill(), this routine is supposed
to be called on IRQ, and the waiting loop was shown to interfere
with interrupt-driven UART handling.
The original problem mentioned in the patch being reverted ("it is
possible to evaluate the TXE bit *before* H/W has had the
opportunity to detect that data is being processed") may still
exist and may require handling in a different way. The most obvious
way is to replace "while" loop with "if", because STM32 doesn't
have multi-level FIFO anyway. But I was dissuaded to include such a
change as part of this patch, so it's left for future analysis.
This reverts commit 49c2858d94.
Change-Id: Ib27b53ba3a29b84c1a2dccff6d33f4118680cc19
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add tickless kernel support. Sets timer always in one
shot mode to the time the kernel scheduler needs the
next timer event. Uses mili seconds as the scheduling
time unit.
Jira: ZEP-1817
Change-Id: Ia2e63711cdd9d7d9c241b9ff08a606aa79575012
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Add tickless kernel support. Sets timer always in one
shot mode to the time the kernel scheduler needs the
next timer event. Uses mili seconds as the scheduling
time unit.
Jira: ZEP-1818
Change-Id: I21ce037b571c4c6ff588033a15aa49624cba7a57
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Add tickless kernel support. Sets timer always in one
shot mode to the time the kerneel scheduler needs the
next timer event. Uses mili seconds as the scheduling
time unit.
Jira: ZEP-1816
Change-Id: I85232b572759b9653c6396edc057ff4409525c97
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Update the timer to use the tickless kernel interface
provided by kernel to operate in event based mode. In
this mode, the timer would not generate periodic ticks
and would only be programmed in one shot mode. It would
announce elapsed time in wall time units instead of
ticks. Timer can also be disabled enabling waiting
forever for a non-timer event.
Jira: ZEP-1812
Change-Id: I13110b9fb53b33a9244cc91a3d991f8452d330b1
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Adds event based scheduling logic to the kernel. Updates
management of timeouts, timers, idling etc. based on
time tracked at events rather than periodic ticks. Provides
interfaces for timers to announce and get next timer expiry
based on kernel scheduling decisions involving time slicing
of threads, timeouts and idling. Uses wall time units instead
of ticks in all scheduling activities.
The implementation involves changes in the following areas
1. Management of time in wall units like ms/us instead of ticks
The existing implementation already had an option to configure
number of ticks in a second. The new implementation builds on
top of that feature and provides option to set the size of the
scheduling granurality to mili seconds or micro seconds. This
allows most of the current implementation to be reused. Due to
this re-use and co-existence with tick based kernel, the names
of variables may contain the word "tick". However, in the
tickless kernel implementation, it represents the currently
configured time unit, which would be be mili seconds or
micro seconds. The APIs that take time as a parameter are not
impacted and they continue to pass time in mili seconds.
2. Timers would not be programmed in periodic mode
generating ticks. Instead they would be programmed in one
shot mode to generate events at the time the kernel scheduler
needs to gain control for its scheduling activities like
timers, timeouts, time slicing, idling etc.
3. The scheduler provides interfaces that the timer drivers
use to announce elapsed time and get the next time the scheduler
needs a timer event. It is possible that the scheduler may not
need another timer event, in which case the system would wait
for a non-timer event to wake it up if it is idling.
4. New APIs are defined to be implemented by timer drivers. Also
they need to handler timer events differently. These changes
have been done in the HPET timer driver. In future other timers
that support tickles kernel should implement these APIs as well.
These APIs are to re-program the timer, update and announce
elapsed time.
5. Philosopher and timer_api applications have been enabled to
test tickless kernel. Separate configuration files are created
which define the necessary CONFIG flags. Run these apps using
following command
make pristine && make BOARD=qemu_x86 CONF_FILE=prj_tickless.conf qemu
Jira: ZEP-339 ZEP-1946 ZEP-948
Change-Id: I7d950c31bf1ff929a9066fad42c2f0559a2e5983
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
If setting up crypto context fails enough times, the sessions will all
end up "in use" though they will not. This will lock tc shim driver
altogether and no crypto context will be possible to run on it.
Change-Id: I72346854e52294f96afc32f30ac5bfd0c368812b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Thus it is possible to reduce or raise such amount relevantly if
required.
Change-Id: Ib53131e10e69fcbf1bcd9d844703d5b8832ee224
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
All existing log entries add a line break, so let's just use the sys_log
way.
Change-Id: Ia94efa593700e9590e16b51262f0b5a2fe10ffa2
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As everywhere else in drivers, domain of driver should be used as name
prefix.
Change-Id: I1bb2284495c7a6b2648395b757a5f912e4410b15
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As it is a crypto driver, let's prefix all options with CRYPTO_ as it is
done everywhere else.
Change-Id: I1eccbf655417664a1f031a221081b0b1db673394
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- help message should have same intendation on a specific file
- No need of "depends on" if it's already in a relevant if/endif
- either prompt is used, or not, but let's not mix.
Change-Id: Ib75f25dcf2440fd0ba7bde5c95bc1fbece68be07
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix misspellings in Kconfig help text and made spelling of
RX and TX consistent (from reviewer comments)
Change-Id: Ie9d4c3863cd210e7a17b50a85a7e64156b6bf3d7
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types. This handles the remaining includes and kernel, plus
touching up various points that we skipped because of include
dependancies. We also convert the PRI printf formatters in the arch
code over to normal formatters.
Jira: ZEP-2051
Change-Id: Iecbb12601a3ee4ea936fd7ddea37788a645b08b0
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Even one liner if () should have get { ... }
Change-Id: I7f9d8d74398286e97549bed050e29d4d175e1b02
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I4ec03eb2183d59ef86ea2c20d956e5d272656837
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- net_pkt becomes a stand-alone structure with network packet meta
information.
- network packet data is still managed through net_buf, mostly named
'frag'.
- net_pkt memory management is done through k_mem_slab
- function got introduced or relevantly renamed to target eithe net_pkt
or net_buf fragments.
- net_buf's sent_list ends up in net_pkt now, and thus helps to save
memory when TCP is enabled.
Change-Id: Ibd5c17df4f75891dec79db723a4c9fc704eb843d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There have been long lasting confusion between net_buf and net_nbuf.
While the first is actually a buffer, the second one is not. It's a
network buffer descriptor. More precisely it provides meta data about a
network packet, and holds the chain of buffer fragments made of net_buf.
Thus renaming net_nbuf to net_pkt and all names around it as well
(function, Kconfig option, ..).
Though net_pkt if the new name, it still inherit its logic from net_buf.
'
This patch is the first of a serie that will separate completely net_pkt
from net_buf.
Change-Id: Iecb32d2a0d8f4647692e5328e54b5c35454194cd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I8f57a17f78e674aca5400f005db8975c9f9e150e
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is a start to move away from the C99 {u}int{8,16,32,64}_t types to
Zephyr defined u{8,16,32,64}_t and s{8,16,32,64}_t. This allows Zephyr
to define the sized types in a consistent manor across all the
architectures we support and not conflict with what various compilers
and libc might do with regards to the C99 types.
We introduce <zephyr/types.h> as part of this and have it include
<stdint.h> for now until we transition all the code away from the C99
types.
We go with u{8,16,32,64}_t and s{8,16,32,64}_t as there are some
existing variables defined u8 & u16 as well as to be consistent with
Zephyr naming conventions.
Jira: ZEP-2051
Change-Id: I451fed0623b029d65866622e478225dfab2c0ca8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix doxygen comment typos used to generate API docs
Change-Id: I6fd5051c99bdcc731740c92001e525349c254d85
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This reverts commit e60af3be66.
We revert this as we intent to move away from {u}int{8,16,32,64}_t types
to our own internal types for sized variables so we shouldn't need the
PRI macros anymore.
Change-Id: I4a57eb2c23cb1b137112224f604602d40c7cce4f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To allow for various libc implementations (like newlib) in which the way
various {u}int{8,16,32}_t types are defined vary between both libc
implementations and across architectures we need to utilize the PRI
defines.
Change-Id: I69e60e3823028389b314adaf6e279fd47fde1182
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added serial (UART) driver for Atmel SAM MCU family.
Note:
- Error handling is not implemented
- The driver works only in polling mode, interrupt mode is
not implemented.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1959
Change-Id: I3e770fd1feb2ddf92cf405a9aa17be92eb32e19b
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added I2C bus (TWIHS) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1866
Change-Id: Ic5aa7b6b21295feccae883d580b38bbeaf2ce291
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add plumbing to build system and SoC level dtsi for the NRF52832 SoC.
We additionally add the necessary yaml files for the UART on the NRF52
SoCs.
Change-Id: I3b4a821b2993827e33d8e84bdbbc759d1521f8bd
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The MKL25Z soc do not support irqs in PORTB, PORTC and PORTE.
This is a patch to not enable irq if such ports are enabled.
Change-Id: I7b0b308504fcea47714fee8f2913baf336c4aa7d
Signed-off-by: Gustavo Denardin <gustavo.denardin@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all STM32 platforms are using device tree we can remove the
handling for !HAS_DTS from the serial driver.
Change-Id: Ifafc283f2509dd9a438f321e0b647720d4f13810
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all NXP MCUX platforms are using device tree we can remove the
handling for !HAS_DTS from the serial drivers.
Change-Id: I05185142afa7fae83ce68de954202829868af88f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Wrong base address has been provided to I2C_2 instance.
Fix this issue for proper behavior
Change-Id: I81e5cb71a5136e742f460db5db39b2adf2f10f2d
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
I2C_SHARED_IRQ, I2C_0_IRQ_SHARED, I2C_0_IRQ_DIRECT Kconfig options
are DW driver specific. Its presence is confusing for a user of any
other I2C driver than DW. This patch renames these options to include
DW string and makes it visible only for DW I2C driver. This is a
similar implementation to that used by ETH DW Ethernet driver.
Change-Id: I795506f9b103c028a22317df9ad632dce5cd1343
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add support for nRF5x series GPIOTE based PWM driver
implementation.
Provides upto 3 pins/channels using one HF timer, two PPI
channels per pin, and one GPIOTE config per pin.
Change-id: I6056b199ec2cff595ba8fea9f659a0338ed4635b
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Correct the way interrupts are enabled and disabled using the INTENSET
and INTENCLR registers, which ignore all 0s written to them and are both
positive registers.
Change-Id: I052548b0255d9d5ae36b2a708ed1968ae3ab1d06
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
simcall must be in the volatile asm so that gcc does not optimize it
out. It also needs "memory" clobber to make sure data passed through
memory buffer is actually written back before the simcall.
Change-Id: I410b7348bf605d0d08f81ec5395f6cb144f33a43
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Check net_recv_data() return value, if it returns an error release
the net_buf. Based on a fix in eth_mcux driver.
Change-Id: I44ca5fd8dfb7175620b7e8850a68443100039db6
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add the simplest possible CRC 16 function that computes the CRC value
without the help of lookup tables.
Change-Id: I9163389adaa4a70c4e8ce8ce6d5f0661f40c7871
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Check net_recv_data() return value and if it returns an error
then release the net_buf in order to avoid leaking it.
Coverity-CID: 158884
Change-Id: I10d411a2de4b7c7bbe2475df65d93f5b1e619679
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
CONFIG_* usually come from Kconfig, rename variables that are locally
defined to avoid confusion about where they are set.
Change-Id: I83b8459913c5deb68dc1b9f5386b8934363a6d1f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
That option was not defined and the sensor does not have this feature,
probably was part of some copy/paste mistake.
Change-Id: Ib24d1f85cf90648b01fa81b285a1ec01fe28c545
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The following warning occurs when !SYS_LOG_INF due to the fact
that these variables are only used for information purposes.
When logging is <INFO then the variables aren't utilised at all.
To fix this we're removing the variables completely and using
the direct calls from within the information prints instead.
drivers/dma/dma_stm32f4x.c: In function 'dma_stm32_dump_reg':
drivers/dma/dma_stm32f4x.c:196:11: warning: unused variable 'sfcr' [-Wunused-variable]
uint32_t sfcr = dma_stm32_read(ddata, DMA_STM32_SFCR(id));
^
drivers/dma/dma_stm32f4x.c:195:11: warning: unused variable 'sm1ar' [-Wunused-variable]
uint32_t sm1ar = dma_stm32_read(ddata, DMA_STM32_SM1AR(id));
^
drivers/dma/dma_stm32f4x.c:194:11: warning: unused variable 'sm0ar' [-Wunused-variable]
uint32_t sm0ar = dma_stm32_read(ddata, DMA_STM32_SM0AR(id));
^
drivers/dma/dma_stm32f4x.c:193:11: warning: unused variable 'spar' [-Wunused-variable]
uint32_t spar = dma_stm32_read(ddata, DMA_STM32_SPAR(id));
^
drivers/dma/dma_stm32f4x.c:192:11: warning: unused variable 'ndtr' [-Wunused-variable]
uint32_t ndtr = dma_stm32_read(ddata, DMA_STM32_SNDTR(id));
^
drivers/dma/dma_stm32f4x.c:191:11: warning: unused variable 'scr' [-Wunused-variable]
uint32_t scr = dma_stm32_read(ddata, DMA_STM32_SCR(id));
Change-Id: I91a0373ef6c9afa8a342181c0ab24bd58743300d
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To follow Zephyr convention this patch is placing all I2C driver
Kconfig options in submenu.
Change-Id: Ibc485305b7effb65ed7f24b933fe35d0fa0afee8
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
I2C_CLOCK_SPEED Kconfig option is DW driver specific. It does not
define I2C interface speed but rather the I2C DW module clock speed.
It is confusing for a user of any other I2C driver than DW.
This patch renames this option to I2C_DW_CLOCK_SPEED and makes it
visible only for DW I2C driver.
Change-Id: I97f57332fd5cca644eabdef0968a0b2174b885ff
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Atmel SAM family GMAC Ethernet driver is implementing zero-copy
networking. As a result it has to reserve a defined amount of RX
data net buffers before bringing up the interface. Since net buffer
pool is initialized by the network stack and this driver was bringing
the interface up in its initialization function the driver initialization
was performed, as a workaround, after network stack initialization. It
is not a clean solution. This patch fixes this by bringing the
interface up in interface initialization function. The driver itself
can now be initialized before the network stack is.
Tested on Atmel SMART SAM E70 Xplained board
Change-Id: I65886fd6db6f27a10628e393cfabd8e5f78c08ff
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Fix eth_tx function which was dereferencing a pointer before
checking that it is not null.
Tested on Atmel SMART SAM E70 Xplained board
Change-Id: Idae4cf9d9a80f6ee9f74a94dd1debe7511c5fab4
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Adds basic sensor driver support for the Maxim MAX30101 heart rate
sensor.
This driver does not yet support any sensor triggers such as the data
ready trigger, or runtime changing of sensor attributes.
Default configuration values were taken from the MikroE Hexiwear driver.
https://github.com/MikroElektronika/HEXIWEAR
Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX30101.pdf
Jira: ZEP-720
Change-Id: Ie8981e124da36a56a214f133bf9a11b9f47d60fa
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Both the string and image rendering may want to take advantage of
scrolling and sequential display capabilities. Consolidate the APIs so
that there's a single one for images (mb_display_image) and a single
one for strings (mb_display_print). Both take a duration parameter for
the per-frame duration as well as a mode parameter which specifies
sequential vs scrolling behavior as well as an optional looping flag.
Change-Id: Ia092d771e3f1b94afd494c7544dab988161c539e
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Reorder the struct members for more compact layout. The current row
tracker tracks just values 0 to 2 so uint8_t is more than enough for
it.
Change-Id: I845c84aeb32d59ed0ebbd55d8b6cfda7ad19b75a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We don't need to store copies of the current and next image when
scrolling text, since looking up the font is just as efficient and
also consumes less memory.
Change-Id: Ia905164c5b5784afb52cb2bb38c1ab1d00817df0
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add a helper function to reset the state of the display, and make use
of it from the various public functions. This also ensures that the
timer is stopped before starting a new display routine.
Change-Id: I8a916b5b13c18b41b7fc3593e6d97e874ef117af
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add an empty column between characters of scrolling text so that the
individual characters are more easily distinguishable instead of being
back-to-back mashed together.
Also adjust the default scrolling step interval so that the character
display frequency stays roughly the same as before.
Change-Id: Idca0dc149a84f3f99b753a28ad1120ce75b97667
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For a better clarity and minimize the possibility
of false definitions and duplicates, gather defines
by port and store the by alphabetical order then in
alternate function order.
Change-Id: Ib9febc9e6c5037a774190007120b87bf100c3fca
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
* SPIMx support for nrf52 spi interface with easy dma
Change-Id: I3221b14867924b91a9d809faf689090574f5dc1c
Signed-off-by: Roger Lendenmann <roger.lendenmann@intel.com>
Add support for I2C_2 instance on stm32lx driver
Change-Id: Iaa17305dd21f92954274ca522d30d464e0a53b7b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
It is envisaged that this will be used by SoC or board code to make
available fixed purpose memory-mapped i/o registers to the rest of the
system which normally expects to use GPIO devices, e.g. for driving chip
select lines, LEDs or reading button states.
As such, the driver code doesn't provide a kconfig based configuration
mechanism, instead SoC/board code can hard-wire the devices it wants
with something simple like:
GPIO_MMIO32_INIT(misc_reg1, "MISC1", 0x12345678, 0xffffffffu)
Then, for example, if bit N of the register at 0x12345678 is wired up as
an SPI device chip select line, the SPI driver could be configured to
use pin N of the "MISC1" GPIO driver and not need any other board
specific code.
Change-Id: Ib02fcbab73fcf9637e25834db060fb3108626f47
Signed-off-by: Jon Medhurst <tixy@linaro.org>
On stm32 family, IP instance numbering starts from 1.
Update i2c driver to this scheme to minimize user
confusion
Change-Id: I967d5975bbbad59cd8a3a7b6dfc665955d09cc9f
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
As part of the transition to Device Tree, a temporary
HAS_DTS configuration variable, and a .fixup file per board
with symbol aliases were added.
This patch removes the cc32xx related fixup file
definitions, except for those used additionally outside
the cc32xx drivers.
Since cc32xx has DTS files, and since HAS_DTS will always be true,
it also removes the 'if !HAS_DTS' blocks from the cc32xx Kconfig
files.
Change-Id: I1c1b9f734795f523342f82ab32f2a38983812c0b
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Previously, cc3200_launchxl board was not able to show the
Zephyr Boot Banner, as that required early initialization
of the UART driver, which was done POST_KERNEL.
This patch moves the pinmux and UART driver initialization
to PRE_KERNEL_1, allowing early printk, and the Boot Banner
to show.
Change-Id: I84a7c20c1d5bdc3de150dc6bb0adebc9a2d9f5cb
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Add a new mb_display_print() API which takes printf-style parameters
and outputs scrolling text instead of one character at a time. The
existing mb_display_str() API is renamed to mb_display_string() for
consistency, and now also takes printf-style parameters.
Change-Id: I59c42bcd74c62f05ecb6d097dc808b9e5c1984c5
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Adds a simple driver to access the 5x5 LED display found on BBC
micro:bit boards. The display is so limited that no effort is done to
try to integrate with the existing console (which would likely make
the display unusable). Instead, dedicated mb_display_* APIs are added
that are specific to this display.
References:
https://www.microbit.co.uk/device/screenhttps://lancaster-university.github.io/microbit-docs/ubit/display/
Jira: ZEP-1990
Change-Id: I431b5b358b5f07592a60d3aed87eaab6ac20ce25
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SiFive Freedom E310 Platform Level Interrupt Controller (PLIC) follows
the riscv PLIC specification as defined in the riscv privilege
architecture specification.
It provides implementation for the riscv PLIC APIs as
required by the riscv-privilege SOC Family for SOCs providing
support for the RISCV_HAS_PLIC config.
Change-Id: I95d02edb53deeccd91e490776e8e1dbfb82d235f
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
Rearming the riscv machine timer is done by first updating the
mtimecmp low value register. If the low value is updated with a
relatively small value, a timer interrupt can be generated while
updating the mtimecmp high value.
To avoid such a spurious interrupt to occur, disable the timer
interrupt while rearming the timer.
Change-Id: I50ab3f19554a9a8dfe70943b6da0d20be3de88dc
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
This will provide the feature through Crypto API.
Change-Id: If6953a54b393544b019755ae73571effe0724e69
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Without this bit set, if we a pass ptr to a string such as:
"This is a string\n"
The DMA'ed output would be:
"TTTTTTTTTTTTTTTTTT"
Change-Id: I0186c95ddca0390596d22af2551dbfa6716a5082
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The device data structure is statically declared and referenced
on a per-controller basis during driver registration. Unfortunately,
due to using the same name (ddata) to initially declare as used
in individual functions, we accidentally referenced the main struct
by mistake due to a lack of local declaration. Let's prevent that
from happening again by using different name-spaces.
Change-Id: I9f7e5e7f95ee68d71aee70fa979e015ca2b5519e
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The STM32 DMA controller supplies streams, which in turn provide a
selection of channels. The stream number is provided by the DMA API
through it's 'channel' argument, but the sub-channel (within the
stream) is specified on an application case by case bases via Kconfig.
Change-Id: Ib5bfdb80f4d616516850787e1402164807771c5e
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Some controllers contain channels with-in channels, or in the case
of the STM32 DMA controller channels within streams. Channels
will vary depending on application, so these need to be provided
on a use-case bases.
Change-Id: I4f5fe3ec5817583b95dc7f059b5dc57f937523c4
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes the fxos8700 Kconfig help indentation to be <tab><space><space>.
Change-Id: If6e9395b5d28044962ca568be5515658e7dc2627
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds sensor driver support for the NXP FXAS21002 3-axis gyroscope.
Includes statically configurable range and output data rate, as well as
the sensor data ready trigger.
Datasheet:
http://www.nxp.com/assets/documents/data/en/data-sheets/FXAS21002.pdf
Jira: ZEP-1392
Change-Id: I84587c4d5e76863245e9d045c6abb10b21b2615a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Each controller contains a number of streams. Subsequently each
stream contains a number of channels. Channels are selectable
via the stream's control register.
Change-Id: Ib75d1377cb8fc38f27e4566b275343b2ffb8da65
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit c0bd8a0ce4 ("api: dma: dma api update") introduced some new APIs
and deprecated the old ones. Let's move to the new API before the old
calls are completely removed.
Change-Id: I21795fa20124f8101c56b0fceb0f0d9afd96b0f0
Signed-off-by: Lee Jones <lee.jones@linaro.org>
File include/misc/sys_log.h has been moved to include/logging/sys_log.h.
Change-Id: I011ca632396b574ae7e388b47fc2ba3a58fafc7b
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Providing a new line, then an attribute on the same line as the
following closing bracket is odd. Move to something more
transitional and in line with regular coding standards.
Change-Id: I08f7cd76ca2f522a8b5b6de2e5baf94e95b5195a
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is possible to evaluate the TXE bit *before* H/W has had the
opportunity to detect that data is being processed. Therefore
we should hold off on any evaluation until TXE has initially been
set.
Change-Id: Iff26bfbe3ab419734003bf81a4cb357de83908e7
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently only 1 is allowed. While we're at it, let's generify the
existing entries, since they could be used by all controllers, not
just QMSI.
Change-Id: Iec5d195fff239931b21a7584eb4b642b40f95be5
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the entries for STM32 UART ports are at the same level than
the top menuconfig UART_STM32. As a result they are mixed with other
configs in the "Serial Drivers" menu.
Use if/endif grammar to put these entries under a dedicated STM32
submenu.
Change-Id: If28945204b801578d29f8cce7c2370ca3c2737a1
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Add support for GPIO banks I to K that can be found on some high-density
STM32F4 products.
Change-Id: I2cb65ed4d4a2282f7d17478cb1fcdd65dffe71b0
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The registration of each GPIO bank differs by only few details. These
differences can be factorized in order to create a generic registration
macro.
This has several advantages:
- Less code
- Easier to add new banks
- Less work to add support for new STM32 families
The diff stat speaks for it-self: 26 insertions(+), 92 deletions(-)
Change-Id: I674752fda5ee3caefb815ccf070a1b636b16cf85
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
The PLLN multiplier can range between 50 and 432 on all STM32F4, except
on the STM32F401 where the lower bound is restricted to 192.
Fix the range property and the help text to reflect this reality.
Change-Id: I7b93e84b321f7869aaf611287344cd3e25c893c8
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Since all interrupts come in on the status line,
we only connect it for the KL2X.
Change-Id: Ia9e0d483fe68464a0eeab08c95a043260e5793b0
Signed-off-by: Gustavo Denardin <gustavo.denardin@gmail.com>
Clear pending IRQ when starting and restore back the RTC1 state when
disabling sys_clock, to avoid issues when soft rebooting the device or
chainloading another Zephyr image (e.g. mcuboot).
Change-Id: I693d9168196ad2cfb8475ecfa2051eac043b1fbd
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
In prep for supporting the older KL2x SoCs that use a different SPI
block, rename the current SPI driver to DSPI to match what the MCUX HAL
defines it as.
Change-Id: I9097580df5fca649ab6fd9a38212fced0b1ea6ed
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
At the moment CC2520 configuration options are selected inside "TI
CC2520 Driver RAW channe" submenu like:
[*] TI CC2520 Driver support ----
[ ] TI CC2520 Driver RAW channel --->
Make RAW channel depends on TI CC2520.
Change-Id: I92879b7f4391f1842c012b6c03c78956e90b9441
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The fxos8700 is primarily an accelerometer/magnetometer, but it does
also include a temperature sensor. Note that the temperature sensor is
uncalibrated and can only be used when the magnetometer is enabled
(magnetometer-only mode or hybrid mode).
Change-Id: I74c4ae68c30e0f9836caa70baed44ad8956b17ea
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Declaring these as const lets the linker generate more optimal code.
Some extra care is needed with hci_ecc.c since it was overwriting the
send callback. Now the choice of send() call is done directly in the
bt_send() function
Change-Id: Iac74f5ee9bee097bbb34c11bd13d1d886700f5cc
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Support connection via SPI and keep I2C as the default.
Jira: ZEP-1698
Change-Id: I42a76131577a37429375364deb07e451107f5d81
Signed-off-by: Dario Pennisi <dario@iptronix.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Allow user to set the four last bytes of a MAC address.
By default the bytes are selected randomly but for testing
purposes we need a way to specify the address in advance.
Change-Id: Ic9820a8026b327d1ee5025ab77fdc77f5778de67
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Networking stack has split one global DATA pool to RX and TX DATA pools
and also added net_buf pool support to each context. Update the driver
to support this new design. Since the GMAC TX descriptor list has a fixed
size but the number of TX DATA buffers is no longer limited updating the
TX descriptor list has to be guarded by a semaphore.
Tested on Atmel SMART SAM E70 Xplained board
Change-Id: I181e1cdd183e173b85d5d1711b6e78cd5165666d
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
It is possible that the slip->last pointer is not set during
the startup of the slip driver if we receive some garbage bytes.
This in turn caused memory to be overwritten in random places.
Jira: ZEP-1737
Change-Id: Ia2ce193b81a8f707b7ca63497d497ea70699bb32
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
No need to always look through all the network interfaces
when receiving packet as we support only one interface and
it is always the same one.
Change-Id: Ic0bfabc8409160352081cac1a6c3dbbfa35fe390
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The current state of affairs will not allow to set a MAC address and
thus will initialize a random MAC address.
However, when we are in a situation where we are trying to interface
Zephyr OS QEMU VMs with physical targets for testing, this is not
practical. We need to create a macvtap interface, on which we need to
set the MAC address of the Zephyr OS SLIP device so packets can be
routed. There is no way to guess which random address is going to be
used, and there is no practical way to query it.
So this patch adds a CONFIG_SLIP_MAC_ADDR config
setting. slip_iface_init() is changed to take the code from
slip_get_mac() for initializing the MAC address (which should be
happening there anyway) and if CONFIG_SLIP_MAC_ADDR is set, it takes
that one -- otherwise goes to generate a random one.
Change-Id: I55a68f2743604f310d41c934783eca82084d7e94
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Add few nop instructions to allow the DMA controller settle,
It takes time after starting the transfer to access the DMA
controller registers, so a few cycles are added, the minimal number
of cycles needed has been calculated using tests results on c1000
development board.
Jira: ZEP-1803
Change-Id: I1f8e8478f0350e1b6e4dd596b783dc4babc2d02b
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
This commit adds missing RAW mode device to the driver.
Change-Id: I9ee9c41bc94b0ae202613ef707030033b46df1de
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
The PHY debug code is useful while working specifically with the PHY
state machine, but in general the frequent, periodic nature of the
output is a hinderance. Turn down the verbosity, leave a local define
available for anyone who specifically needs to see the PHY state
machine debug.
Change-Id: I40e59b6df5c29702813d3a554ea9e795a3761c65
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The enc28j60's reception routine requires a timeout
for a buffer assignation. The timeout is configurable
to allow a per application fine tuning.
The effect that K_NO_WAIT currently has is that there are frames
lost everytime that a buffer is required and there are none
available.
Jira: ZEP-1169
Change-Id: Ia18736fd85daee51fe1c2304977209cc7f0038b5
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
The code used net_nbuf_get_reserve_{rx|tx}_data() function to
allocate a fragment. Instead of that low level function, use
net_nbuf_get_frag() instead. There are few places this is not
possible or is too big change like in few test programs.
Change-Id: Ied7e2b7db352de998b200ffa6ff82471bfa5ebe3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive lot of packets, it might happen that we exhaust
all the DATA buffers in the system. This would prevent from
us sending anything to the network.
Change this by splitting the DATA buffer pool into RX and TX
parts. This way RX flooding cannot consume all DATA buffers
that needs to be sent.
Change-Id: I8e8934c6d5fdd47b579ffa6268721b5eb3d64b6d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Provide a configuration option for promiscuous mode.
Promiscuous mode provides a convenient workaround for ZEP-1673 however
it generates significant demand for RX buffers on a loaded network.
Add a configuration option to conveniently enable / disable.
The Kconfig defaults promiscuous on to workaroudn 1673, once that
issue is resolved the default logic on NET_IPV6 will be dropped.
Change-Id: I6929aca70d7bd88ce88c65d6654d664ea6653b66
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Basic Watchdog driver for Atmel SAM family MCUs. Currently only
disabling the watchdog is supported.
Tested on Atmel SAMV71 Xplained Ultra Evaluation Kit.
Origin: Original
Jira: ZEP-1684
Change-Id: I8f717c7f53aa290c944b7935e0570c2a6f53956e
Signed-off-by: Souvik K Chakravarty <souvik.k.chakravarty@intel.com>
Provide a random driver wrapped around the MCUX TRNG driver.
Change-Id: Icbd7ab587aa18ecbd7eae52290aaa5d8ee504cf2
Origin: Original
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
MCUX contains more than one type of random number generator,
so refrect this in config and file names.
Change-Id: Iba4482a1ae41f35d471686f8b159c113147c4df8
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Current users of sys_bitfield*() are bending over backwards to cast
what is most of the times a pointer into an integer.
Bitfields can be better described with an void *, so
uint{8,16,32,64}_t or any other container can be used. Most
sys_bitfield*() operations, by extension, can do the same. Note void *
has byte arithmetic, like char *.
This change will also make it implicit, for any future split of the
address space between virtual (what the SW is seeing) and physical
(what the HW is seeing) way clearer, as the functions dealing with
physical, non directly referentiable/mappeable addreses to use an
integer type, like mem_addr_t.
- include/arch/ARCH/*asm_inline*:
- sys_bitfield*() all modified to take 'void *'
Note 'void *' arihtmethic is byte based, which makes some things
easier.
- include/sys_io.h:
- introduces DEFINE_BITFIELD
- update docs
- tests/kernel/bitfield: remove all the cast contortions, use DEFINE_BITFIELD
PENDING: update other TCs
- include/arch/nios/nios2.h, drivers/interrupt_controller/ioapic_intr.c:
remove cast contortions
Change-Id: I901e62c76af46f26ff0d29cdc37099597f884511
Jira: ZEP-1347
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
These are more consistent with naming used by other ports (uppercase,
short), and some existing software relies on them to be exactly those.
This change is a follow up to the discussion on the Zephyr mailing
list, calling to establish consistent naming conventions for Zephyr
devices, and is a small step in that direction.
Change-Id: I013b0505b579c6337aeb6fbef2423216ca6cf046
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
To secure correct signal levels on the pins by the UART when
the system is in OFF mode, the pins must be configured in
the GPIO peripheral as described in nRF5 Product
Specification.
UART Pin, Direction, Output Value:
RXD, Input, NA
CTS, Input, NA
RTS, Output, 1
TX, Output, 1
This commit sets the RTS line to a initial value of 1.
Change-id: I5147fe58033f42c979b9354798b6fd13d78f7f71
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
To avoid glitches in the lines, set the line to the pull specified
before actually changing the line's direction (in/out) so that no
unexpected pulses are generated.
Change-id: I4fe133c5b82f2a1bfa473341612c2c7eca9027b8
Signed-off-by: Krzysztof Chruściński <Krzysztof.Chruscinski@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Refactor the PHY state machine and add support for explicit start and
stop.
The stop implementation remains partial, the state machine will enter
a disabled state but will not actual attempt to power down the PHY.
This is deliberate, while implementing this it has become apparent
that issuing a PHY power down command is an effective way of bricking
frdm-k64f boards, hence explicit power down deliberately disabled
until the issue is properly understood.
Change-Id: I846a51b0ac48feed35d260cf20b50f4f1ac59298
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Add the link type to net_if_set_link_addr() call. This fixes the
driver after changes introduced in
4eb2020055.
Change-Id: I72475a055ac805524b4b0f0c2380513e8f041368
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
Some fixes where needed to get PLL2 source of PREVI1 functional.
Compiled ok with following configuration:
CONFIG_CLOCK_STM32F10X_CONN_LINE_PREDIV1_SRC_PLL2CLK=y
CONFIG_CLOCK_STM32F10X_CONN_LINE_PREDIV2=0
CONFIG_CLOCK_STM32F10X_CONN_LINE_PLL2_MULTIPLIER=8
Jira: ZEP-1758
Change-Id: I5ddfaef1b44c4c4e5e6adedc158a1c9092bc8df5
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Some GPIO ports activation where missing since not used
on available soc/boards.
Since stm32 family increases, activation of these ports
should be made available.
Jira: ZEP-1551
Change-Id: I612d135b28ef255bc771599e33796671ff81d0ac
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We need to account for the interrupt happening in the middle
of the calculation.
Issue: ZEP-1546
Change-Id: I193534856d7521cac7ca354d3e5b65e93b984bb1
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Using net_nbuf_unref to release the net_buf so that we can
debug the allocations more easily. It is ok to use the original
net_buf_unref() too, we just miss some important net_buf
housekeeping information if done like that.
Change-Id: Ieb7b39ed525bfc46eb5c07a01f2a3a75fdbeb9fd
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If slip_input_byte fails to get buffer for the first byte then no point
of saving later bytes and send it to upper layers. Final packet will be
incomplete and upper layers will discard it. Consider incoming bytes
only after successful buffer allocation on first byte, otherwise silently
ignore it.
Change-Id: Ie16d0df0c608d1644d39f66900252a340051c012
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
No functionality changes. Added more comments and used switch cases
for more readability.
Change-Id: I9396270d7368d9b0c923a88f90b44129a1d69cbc
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The interface L2 address type is set at the same time as the
L2 address is set to the network interface. This is most
convinient place to set the address type.
Change-Id: I712d7357d075959eb79df3463141cfbc6d163a74
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit adds a driver for nRF5 802.15.4 radio. This driver
is a wrapper for the driver provided by ext/hal/nordic/drivers.
Change-Id: I20ee4aff3d1b994c621ba8eaab208d15d85e4c01
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
The interrupt processing of MCR20A was flawed and complicated.
This patch simplifies the handling of interrupts and reduces
the number of necessary SPI transfers.
Minor fixes:
- use mutex for the PHY access control
- remove unnecessary mcr20a_mask_irqb calls
- do not read RX_FRM_LEN twice
- increase timeout for sequence synchronization semaphore
if the log level greater than 1
- enable only the Sequence-end (SEQIRQ) interrupt
- fix magic in NET_DEVICE_INIT
- make the timeout values dependent on the log level
Change-Id: Ib3f64a092ffba91c80ff6e1d5cec995ab9d40bfb
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Fixes an unlikely issue that could arise if the RTC handler in the nRF RTC
driver was blocked for more than one sys tick interval. This could lead to
_sys_clock_tick_announce() being called with more than one sys tick when the
kernel did not expect it.
Jira: ZEP-1763
Change-ID: I5608fca6f0ac97a17c1ce452c1c5c67696a49a9a
Signed-off-by: Øyvind Hovdsveen <oyvind.hovdsveen@nordicsemi.no>
The LOAPIC driver was doing this in a way susceptible to a very
nasty race condition: the CCR register could reset and be readable
before the associated interrupt could be delivered.
This resulted in a small window of time where CCR was reset, but
accumulated_cycle_count not updated, causing some calls to
k_cycle_get_32() to appear to jump backwards in time.
Just use the x86 TSC for these cycle timestamps. A divisor may be
provided in cases where the CPU clock speed is some multiple of
the bus speed. Modern x86 CPUs do not change their TSC rate even
when adjusting cpu frequency, so this should be a reliable timing
source.
Issue: ZEP-1546
Change-Id: I441bd8e32af866587a91f306e89e3fa0ece512b5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
It's possible the timer interrupt could occur when performing the
computation, resulting in incorrect values returned.
It's still possible for bad values to be returned if the function is
called with interrupts locked, but that is only fixable with a second
timer source.
Issue: ZEP-1546
Change-Id: I16d5b04c3e32377f7249eb4fb1bf2f7c22bd0836
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Some files made it through review process with full license header.
Change-Id: I2722b127c40b4b19500042c12e4fde85a165bae9
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This is a reworked version of the previous RTC driver. The main
changed is related to the handling _timer_idle_exit() on non-RTC
wake-ups. The previous version didn't announce the elapsed time
to the kernel in _timer_idle_exit(). Additionally, the driver now
makes sure never to announce more idle ticks than the kernel asked
for, since the kernel does not handle negative deltas in its timeout
queues.
Change-Id: I312a357a7ce8f0c22adf5153731064b92870e47e
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
Signed-off-by: Øyvind Hovdsveen <oyvind.hovdsveen@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Some arches may want to define this as an inline function, or
define in core arch code instead of timer driver code.
Unfortunately, this means we need to remove from the footprint
tests, but this is not typically a large function.
Issue: ZEP-1546
Change-Id: Ic0d7a33507da855995838f4703d872cd613a2ca2
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
On Nios II the same timer peripheral IP block can't function
as a periodic system timer and a high-resolution timestamp source.
A second timer instance with different configuration is required.
Until that is implemented, just return the accumulated cycle count.
Issue: ZEP-1546
Change-Id: If3dcebdc60334bf3aa0ab45ccd82f1b2531b6bc1
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
There are race conditions trying to coordinate the value between
the accumulated_cycle_count (updated at interrupt time) and
trying to compute the delta from the last interrupt using the
mtime registers. An unlucky call could result in the timestamp
appearing to move backwards in time.
the 'mtime' register isn't reset at every interrupt. Since we just
want a cycle counter, report its raw value.
Issue: ZEP-1546
Change-Id: I9f404b33214d6502fea47374fcf0ecbf84ef8136
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This driver currently only handles memory-to-memory transfers.
TODO: Add support for all types of transfers.
Change-Id: Ic9787dcca919a58fb11b48c9f6b6b371db88c3ea
Origin: Original
Maintained-by: Zephyr
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adds a driver for Atmel Crypto Authorization solution
ATAES132A crypto device.
The driver supports the following functionality.
- AES CCM encryption, decryption and authentication
- AES ECB block operation.
The driver requires an I2C device to access crypto device registers.
Jira: ZEP-1387
Change-Id: I60aa8f3b069b703d4f83d866d28391625bb9ac13
Signed-off-by: Juan Manuel Cruz Alcaraz <juan.m.cruz.alcaraz@intel.com>
Shim layer interfacing between crypto APIs and TinyCrypt
library. Currently facilitates only a subset of TinyCrypt
features/algorithms.
Jira: ZEP-509
Change-Id: I7fe6b9d86df016d92d717378d08a1ab09caafb31
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
When a GPIO pin is configured, the shim driver will first read the
current values in the controller registers to keep the other pins from
changing their configuration. After that it sets the bits for the
corresponding pin accordingly.
When the flag to enable interrupts is passed to the function, the
corresponding bits are all set properly, but no changes are made if
interrupts are not requested. This makes it impossible to disable
interrupts for a given pin once they've been enabled.
Fix it by always resetting the interrupt enabled bit when they have not
been requested. Other values can be left untouched as they won't have
any effect.
Jira: ZEP-1717
Change-Id: I30e97bb06d966291e23d0c66ddf39bce615c287b
Signed-off-by: Iván Briano <ivan.briano@intel.com>
Requesting a flash_write with a length of 0 results in a flash
position being written. Instead we should return 0 unless there is
some other input parameter that is invalid.
Change-Id: Ife6e6e2314bbee2bde7d0b69db3122ca00c361e0
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
This is a workaround for lack of driver API support for multicast
management. So, instead we want to receive all multicast frames
"by default", or otherwise basic IPv6 features, like address
resolution, don't work. On Kinetis Ethernet controller, that
translates to enabling promiscuous mode. The real fix depends
on ZEP-1673.
Change-Id: I98a27584be65bdc405de005383eb30bad2a7fcfc
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add basic PHY management sufficient to detect link up, link down and
auto negotiated link speed / duplex. The PHY driver is implemented as
a state machine that executed in the system work queue. The
implementation is non blocking, using the MII interrupt to capture the
completion of read and write events.
This PHY management should be fairly generic. In the future, it may be
beneficial to pull this code out as a standalone PHY driver for use
with other ethernet drivers.
JIRA: ZEP-1674
Change-Id: I3dcb5c14982ef4b40591fcf10d84840b8a2558e5
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
This driver was written for v1.5 before the introduction of the function
_sys_clock_final_tick_announce. At that time _sys_idle_elapsed_ticks was reset
to 0 automatically. Now that it is reset by the new function, the driver needed
to be fixed.
Change-Id: I039b4dbacb691aaf992b37e44404abd19a54a833
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
This is needed by next commit as some assembly files handling interrupts use
some options from this file.
This file is not included in next commit to separate code and build system
aptches.
Change-Id: Iff3a8019362599beb0c0058c3169480fa5183c1c
Signed-off-by: Mazen NEIFER <mazen@nestwave.com>
These were reported by ISSM compiler.
Jira: ZEP-1179
Change-Id: I10d04c2949ad2a390d4c1159d2342c73108a58b7
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
This commit brings code size optimization as suggested by Christer
Weinigel review during review of initial commit for this driver.
It also cleans up useless definition in header file.
Change-Id: Ibeaa2e51570dff21825c60c30ba83d939b31d938
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After activation of cube based driver support on L4 and F3 series,
this commits performs the clean up of F3 and L4 relative code to
native clock control drivers.
Indirectly, it makes pwm driver supported de facto on F3 series
Change-Id: Idac17103a9b5ef6eab540719343cc8f5865f15fa
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introduction and activation of STM32Cube LL based driver on
F3 and L4 series, this commit removes the no more needed code for
native driver for these soc.
Change-Id: I266d1a3fc4b464cee34b1cc1a1a333c5bf923e41
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update stm32f3xx flash driver to support it.
Clean up will be done afterwards.
Change-Id: I3260bb063f714fa29adbc71d8036f20479a99b34
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update stm32 pwm driver to support it.
Once supported across the whole family, a clean up will be done.
Change-Id: I2ed38763b706e34ea1dceea50e97ce836dd9e195
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update stm32 i2c_lx driver to support it.
Clean up will be done in a following commit.
Change-Id: Ie5059bf4122d65fab1a663a5b00e0d761850a49d
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use of SECONDARY in DEVICE_AND_API_INIT is now deprecated and should
be replaced by POST_KERNEL
Change-Id: I543ae70e493527e75b4a4bcb9191475065b49166
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update stm32 serial driver to support it.
Once supported across the whole family, a clean up will be done.
Change-Id: I7100bc699e7918c8be71d58091da1860ab734e25
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update pinmux driver to support it.
Once supported across the whole family, a clean up will be done.
Change-Id: Icc20816377f3a09f516a743462c92696a1fead3a
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introducing STM32Cube based clock control driver for
stm32 family, update GPIO driver to support it.
Once supported across the whole family, we clean up will be done.
Change-Id: If50cb580cb01dc1d38557e54f19a8260feaa504e
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This new clock control driver aims at providing a lightweight
generic driver to the whole stm32 family.
Driver is based on LL Cube API and hence is for now available
only for STM32 supporting this API: stm32f3xx and stm32l4xx.
Other families should be supported soon.
Once globally supported, this unique driver will also help
reducing the impact of stm32 clock control heterogeneity in
other drivers.
Change-Id: Id15a8d0d44f03809b2907ef10d6877700459e674
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds the base DTS support for the KW41Z Freedom board. The
initial set of changes include SRAM, FLASH, IRQ controller and LPUART
support.
Change-Id: Ic68c4959ddad0c5cfe70d5576a0e58372b93ec9d
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
This patch adds DTS support to the ARM CMSDK UART driver. The DTS
currently specifies the IRQ, IRQ PRIO, and base address of the port.
Change-Id: I8e5bc81c013958be4297d563495bf126b53a83a9
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds device tree support to the STM32 UART driver. The base
address, interrupt, and interrupt priority values can now come from DTS.
Change-Id: I3c383da8b200037601ecb2dc087f99ef103761bb
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch ifdef's out information that would be redefined by
information generated from DTS. This patch also fixes up the serial
drives to work properly with the DTS generated information.
Change-Id: I912ccf35be23c107705a4866e5a68b3b51154ffa
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds DTS support and related files for the NXP Kinetis
platform. The DTS files contain the base definitions for the hardware
nodes on Kinetis platforms. The YAML files provide the definitions of
the contents of the DTS nodes.
The Kconfig changes were put in place to allow for the conversion of
existing drivers. Once those drivers are modified, the Kconfig options
that are replaced by the DTS information will be removed.
Change-Id: If110fffa99c0b12471cf2df206da6687277e4756
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This commit removes unnecessary CONFIG_SYS_POWER_DEEP_SLEEP protection
in shim drivers as QMSI 1.4 has introduced empty context save/restore
functions that can be called in Quark D2000, therefore keeping common
code at the shim driver level for Quark SE and D2000.
Change-Id: Ia2a466327f999668c6511c0193014e9151bff6ae
Signed-off-by: Juan Solano <juanx.solano.menacho@intel.com>
Use new device name for SPI device
Jira: ZEP-1704
Change-Id: Iec39468bbef54423af2b3a681dd4ae1eee866d1e
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update the qmsi dma shim driver based on the new dma api
interface.
Recently, a RFC was posted to update the dma api. The update
to dma api interface was already posted. This change is to
update the dma qmsi shim driver based on the dma api change.
It is using the new data structures and new api function names.
Jira: ZEP-873
Change-Id: If9a772c5ff1c2b10fca05172c48f75223bbf940e
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Enabling the riscv_machine_timer driver by default for riscv32
causes compilation issues on riscv32 boards (like zedboard_pulpino)
not supporting it.
Boards supporting the driver enable it via their respective
config file.
Change-Id: Ieb0d25fa339834fd386ae2725f40b6b7b72dc52b
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
This is one the series patches that simplifies the driver code by
using the IS_ENABLED macro. This removes the need of the const
variable and the wrapper functions on semaphore APIs.
Jira: ZEP-1251
Change-Id: Ic2df5d04966d2a066478ca3e119f76d24fc4dfb3
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
This is one of the series of patches that simplifies the driver
code by using the IS_ENABLED macro. This removes the need of the
const variable and the wrapper functions on semaphore APIs.
Jira: ZEP-1251
Change-Id: I84a09a0aaa3a00452d8c2b4bca7be0f6b2015218
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
This is one the series patches that simplifies the driver code by
using the IS_ENABLED macro. This removes the need of the const
variable and the wrapper functions on semaphore APIs.
Jira: ZEP-1251
Change-Id: I59802cf9f482337656b0fdc4b272f3b1ddc6cbda
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
This commit removes the aonpt interrupt masking/unmasking needed after
wake up as that functionality is now available in QMSI 1.4. The QMSI
save/restore functions are called instead.
Change-Id: I61a4a6952e959d0834904bbc8e1eb98092ae4b1c
Signed-off-by: Juan Solano <juanx.solano.menacho@intel.com>
This commit removes the RTC interrupt masking/unmasking needed after
wake up as that functionality is now available in QMSI 1.4. The QMSI
save/restore functions are called instead.
Change-Id: I15b5063fa64c71b125edd2c709410b5ae655032e
Signed-off-by: Juan Solano <juanx.solano.menacho@intel.com>
Several GPIO device drivers support only one of the two possible
access_op modes and return an errno error code for the mode they do
not support. Use the same errno code across all drivers.
Change-Id: Ic01ce9dee7fb2405d254c60cebee22053c803270
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Several GPIO drivers detect an out of range pin number and return an
errno error code. Use the same errno code across all drivers.
Change-Id: I0e2949432d6845d12c37064c78f9c228b8e8e45a
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Several gpio drivers consider GPIO_INT with GPIO_DIR_OUT to be illegal
and return an errno code. Use the same errno code across all drivers.
Change-Id: I1594df0cfdf96194685c83c34dff36261896f2de
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
This flag is no longer necessary and TICKLESS_IDLE will be
enabled by default if SYS_POWER_MANAGEMENT is enabled.
Jira: ZEP-1325
Change-Id: Ic6cd4b8dc0a17c6a413cabf6509b215a4558318d
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Update the builtin QMSI code to 1.4 (RC2).
The below shim drivers were updated for API or interface changes:
- aio
- counter
- i2c_ss
- rtc
- wdt.
Also, arch soc specific power management code were updated.
Jira: ZEP-1572
Change-Id: Ibc8fae032a39ffb2c2c997f697835bc0208fd308
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
If subcription was found within the subscription list,
we have check if remains identical subscription
from the next node.
Otherwise none unsubscription is realized.
Change-Id: I38132d7c80575801885b8057902f3d4666b08aea
Signed-off-by: Jonathan Gelie <jonathanx.gelie@intel.com>
This commit changes the net_buf getter functions in nbuf.h
by adding a timeout parameter. These function prototypes
are changed to accept a timeout parameter.
net_nbuf_get_rx()
net_nbuf_get_tx()
net_nbuf_get_data()
net_nbuf_get_reserve_rx()
net_nbuf_get_reserve_tx()
net_nbuf_get_reserve_data()
net_nbuf_copy()
net_nbuf_copy_all()
net_nbuf_push()
net_nbuf_append()
net_nbuf_write()
net_nbuf_insert()
Following convinience functions have not been changed
net_nbuf_append_u8
net_nbuf_append_be16
net_nbuf_append_be32
net_nbuf_insert_u8
net_nbuf_insert_be16
net_nbuf_insert_be32
net_nbuf_write_u8
net_nbuf_write_be16
net_nbuf_write_be32
so they call the base function using K_FOREVER. Use the
base function if you want to have a timeout when net_buf
is allocated.
Change-Id: I20bb602ffb73069e5a02668fce60575141586c0f
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit changes Kconfig prefix for ieee802154 drivers to
IEEE802154_*. This is done for consistency with config prefixes
used in other subsystems.
Change-Id: Ibbb4d96d2b748f4f13135bde85304ec34c5a90a6
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
The driver was using net_buf_unref(). This technically works
ok but debugging the network buffer allocations is more
difficult if done like this.
Change-Id: If3453a49337c7a359c8af22cfdf331fccc697af5
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit splits 802.15.4 drivers configuration into separate files.
Change-Id: Ie1bed862e8f4248240fef18bc211d0ee8ca1493c
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
The DW i2c driver chooses to return -EPERM following a PCI error in
driver configuration. This seems an odd choice. All of the other I2C
drivers return -EIO for general failures detected during driver
configuration.
Switch the DW driver from EPERM to EIO.
Change-Id: Ia4f96386620319736ae4c09212b0a05ea38169b1
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The I2C drivers handle an empty list of I2C messages inconsistenty.
There are two different behaviours, one set of drivers dectects a
requests to transfer zero messages and return -EINVAL while the other
group simple transfer no data and return success.
Adopt the latter behaviour consistently across all drivers. Update
the i2c.h API documentation to reflect this behaviour.
Change-Id: I427fc1b0e18ddc04b7b59c294e0240b3d6ca4073
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Subscribe value is set to zero before calling notify callback,
to distinguish a subscription failure from an unsubscription
on disconnection (when flag BT_GATT_SUBSCRIBE_FLAG_VOLATILE is set).
Change-Id: Ia91220492d82041b2c385bf88a15180387e7a483
Signed-off-by: Jonathan Gelie <jonathanx.gelie@intel.com>
Some application protocol required non-persistente subscription
across connection even in bonded case.
Flag BT_GATT_SUBSCRIBE_FLAG_VOLATILE specify if subscription
must be remove during disonnection.
Change-Id: I1bc2bbbb4bc86f58905e44a7eb267ca0871f2fdb
Signed-off-by: Jonathan Gelie <jonathanx.gelie@intel.com>
Implement the missing port read and write behaviour.
Change-Id: I0928379eddf81d806a0ae6b75a1ea2993c3a28ff
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Adjust the implementation of gpio_pin_read() to return 0 or 1 rather
than 0 or 2^pin. This ensures consistent behaviour with other gpio
device drivers, and conforms to the behaviour documented in gpio.h by
the previous patch.
Change-Id: Ia02aa68105a406f355d16a3f9b0550f948658483
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The subscriptions callback may free or reuse the subscription so all
instances that where this could happen need to safely fetch the next
element which is why this changes switch to use sys_list_t as it has
SYS_SLIST_FOR_EACH_NODE_SAFE.
Change-Id: I37d51f27116ea0c057b560924a9416676477597b
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Reduce the pressure on the common RX buffer pool by reusing HCI
command buffers also for the Command Status or Command Complete
response to them. This also implies removing the existing Kconfig
variable for the command buffer sizes since the size is also dependent
on maximum Command Complete event sizes. Instead, reuse the RX buffer
size also for HCI Command buffers.
Change-Id: I006b287d64a0c9ca40de741aa9a424a49a927385
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A subsequent patch will start reusing HCI command buffers for
receiving the response, so the distinction of received vs sent data
headroom would just make the code unnecessarily complex. Instead, just
merge these two variable into a single one.
Change-Id: I31d846331939f1a2270df7ed0c75112825e16493
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If we are low on RX buffers and receive an LE Advertising Report or a
BR/EDR Inquiry response we should just discard this. If we don't
discard the event we increase the risk of deadlock where the RX
interrupt is enabled but bt_recv() is doing a synchronous HCI command
sending, i.e. waiting for a cmd_status/cmd_complete (which will never
come since the RX interrupt is disabled).
Change-Id: I6266625c9790d68bcf8e8718c8c36f127946c4c6
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add sensor sample ready check before fetching the sample.
Otherwise, invalid value will be returned.
Jira: ZEP-1532 ZEP-1358
Change-Id: I570151c8ae93fbb744dac857521f596fd63806a6
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
riscv defines the machine-mode timer registers that are implemented
by the all riscv SOCs that follow the riscv privileged architecture
specification.
The timer registers implemented in riscv-qemu follow this specification.
To account for future riscv SOCs, reimplement the riscv_qemu_driver by
the riscv_machine_driver.
Change-Id: I645b03c91b4e07d0f2609908decc27ba9b8240d4
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
This is a zero-copy networking implementation of Ethernet driver.
Limitations:
- one shot PHY setup, no support for PHY disconnect/reconnect
- no support for devices with DCache enabled due to missing
non-cacheable RAM regions in Zephyr.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1492
Change-Id: Ib944f91193efbd12c1142b0bcf1f635388bf1b87
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added basic USART driver for Atmel SAM MCU family. USART is a very
comprehensive module, currently only basic features sufficient to
support printf functionality are implemented by this driver.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Ia9710e4069243fb6c30de45953dfc1fe1266b63a
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
I found that I was not getting the i2C interrupt.
When CONFIG_I2C_0_IRQ_DIRECT=y, it is acceptable to just
pass the constant to irq_enable.
See ZEP-1651.
Change-Id: I10955e6d6fe5fdd2dda916c92c8bc8a2e871f41a
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Replace _ScbExcPrioSet with calls to NVIC_SetPriority as it handles both
interrupt and exception priorities. We don't need to shift around the
priority values for NVIC_SetPriority.
Jira: ZEP-1568
Change-Id: Iccd68733c3f7faa82b7ccb17200eef328090b6da
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a shim layer around the mcux lpuart driver to adapt it to the Zephyr
serial interface.
NXP has multiple uart hardware blocks that implement different features
and have different register maps. The k64 has a uart block called
'uart', while the kw41 has a uart block called 'lpuart' (low power
uart). The MCUXpresso SDK provides separate drivers for each type of
uart block but with similar software interfaces. As a result, there are
also separate shim drivers in Zephyr. There is a 1:1:1 relationship
between hardware block, mcux driver, and mcux shim driver.
Because we now have two mcux shim drivers for the uart interface, a new
naming convention is created:
<interface>_mcux_<hw block>
Where <interface> is the name of the Zephyr interface, in this case
'uart'. This convention is not new.
<hw block> is the name of the NXP hardware block, in this case 'lpuart'.
This is the new part, and distinguishes different hardware blocks
for the same interface.
Change-Id: I3a80b9bffa116bbb2b02ee950d4bdd79a19a4edc
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The newer version of mcux changes its flash api slightly, so update the
Zephyr shim accordingly.
Change-Id: I0c974fc3e82b9f40372c636f0b805ed143be2198
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
spi_transceive can return successfuly even if the data provided by the
slave is invalid, so check if the content is correct and retry until a
valid data is available.
Change-Id: Ia951de391e0b24c5b41eeabfb5c10b056d32b62e
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Drop the BLUETOOTH_SPI_RX_BUFFER_SIZE and BLUETOOTH_SPI_TX_BUFFER_SIZE
config options by fixing the max SPI buffer length to 255, as used by
the X-NUCLEO-IDB04A1 BSP. This simplifies the rx/tx buffer handling, and
avoids a potential spi rx stack overflow depending on the config values
set by the user.
Change-Id: Ifa7fd086016abda4bdcf9638f28b38d001a288c5
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
This new option is used to encapsulate the logic specific to devices
implementing the BlueNRG Bluetooth stack (e.g. X-NUCLEO-IDB05A1).
The current BlueNRG specific logic covers the HCI Reset handling and
the manual control of the SPI Chip Select line (normally not needed since
spi_transceive is also responsible for controlling the SPI CS line).
Change-Id: I5db4addf873eee0af2d957e2181c50aac53ab656
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Change BREDR_NAME to DEVICE_NAME so it can also be used as the LE
device name.
Change-Id: I9ef55d9dff098372d47d9d5754ad7a7163a65bc0
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Code was assuming that all the HCI messages were events, causing invalid
data length when receiving HCL ACL packets.
Change-Id: I8c1a07f46b6b62a04e242cf29ee1119f59d4bda6
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
SENSOR_CHAN_*_ANY will be deprecated, so use the new SENSOR_CHAN_*_XYZ
enum values.
Change-Id: I91cf25864613a934feab65588969d10c52fd4fe6
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Thus users won't have to first enable network stack and then telnet.
Change-Id: I30cb2b9debee3feaf804f9a70f9d3f90758f5f17
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The cause for this change is TCP. Until now, the radio strategy driver
(ALOHA or CSMA) was providing the actual nbuf, and not the buffer
fragment, counting on the fact that the loop was using
net_buf_frag_del() which made so, iteration after iteration, buffer
framgent to be always buf->frags. The problem with this logic is loosing
the fragments that might be still referenced by TCP, in case the whole
buffer did not make it so TCP can retry later and so on.
Instead, TX now takes the nbuf and the actual frag to send. It could
have been working with just a pointer on the data, and the whole length
of the frame. But it has been avoided due to possible future devices,
that will be smarter and run CSMA directly in the hw, thus it will
require to access the whole buffer list through the nbuf.
Change-Id: I8d77b1e13b648c0ec3645cb2d55d1910d00381ea
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is the skeleton for such support. Let's see if this will be needed
and thus extended in the future.
For now, it's disabled by default, not advised to be enabled.
It supports AYT, AO and DO/SUPR_GA. This is very limited and only there
to show how it could be handled.
Change-Id: I736bfa23145e9b727af08db682ab001f494f8c8d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Telnet "Interpret As Command" (IAC) code is ignored.
Change-Id: I882397389d77b8adfcbce62fbd9654c0b0412ae3
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Let's use the generic console input type now. This will be useful for
other console input drivers such as telnet.
Change-Id: I787a1e9d86481d5f8c4803453726d9042a89dea4
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Input line length can be modified via Kconfig.
Change-Id: I3423fce9814e04b11d11e5d391f85fe1efbe8d17
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Basically missing {} on if statements.
Taking the opportunity to remove a useless switch.
Change-Id: Ic6b3951dfc257cb46d858ebcd12bdf1b4e7ff997
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Telnet is started as an application, as it requires the net stack to be
ready. It will listen to any IP address on both protocols (IPv4, IPv6),
depending of course on which one is enabled.
Current behavior is very basic, as it does not handle any telnet
command (IAC). These will be silently ignored.
Jira: ZEP-1601
Change-Id: Id50656f23e6347bbbc893416953f1ba7116ef87d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of TI_CC2520_CHANNEL option NET_L2_IEEE802154_ORFD_CHANNEL is
used.
Change-Id: I9b0c0ff6b2c42070d05c5cf3e4dc33c364be9a5c
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add driver and configuration for the MCR20A 802.15.4
transceiver.
Jira: ZEP-1429
Change-Id: I0b17b688220a47c2f0e5cde269064bbd0dec824a
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Fixes fxos8700_gpio_callback() to pass a pin number to
gpio_pin_disable_callback() rather than a pin mask.
Jira: ZEP-1507
Change-Id: I15bfbf4d3377f22942aa549377472d2b1142c32b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Remove dev driver and integrate it in the default pinmux driver.
Jira: ZEP-958
Change-Id: I55670240f8a21749d3a6ae22e300e16ba80a2fb6
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Basic interrupt driven i2c driver for the NRf5 series.
The NRf5 series hardware imposes a constraint that various peripherals
cannot be used simultaneously. This driver does not implement mutual
exclusion against SPI, or SPIs drivers (yet).
Change-Id: I308d93bc486eef95db7b95c6b7c9beafc0d7e97f
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Extended the nRF5 GPIO driver to support configurable pin drive
strengths.
Change-Id: I59c42b8a69cc37b594c2388b892d3accd7b19807
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Enable gpio driver automatically when an app or upper
level driver needs it as chip select for spi.
Change-Id: I2bed134939426e2c84f313393d638a878c84fbfc
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
The pulse config option requires triggers enabled, so expand the
trigger requirement to also include all the pulse configs.
Change-Id: Ib94f4071cac757b24bfe940ca64fd11b07fed1c1
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
This avoids asm files from having to explicitly define the _ASMLANGUAGE
symbol themselves.
Change-Id: I71f5a169f75d7443a58a0365a41c55b20dae3029
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
Convert driver to use the CMSIS NVIC APIs rather than the internal ones
so we can remove them in the future.
Change-Id: I7bf3024ea4baf61f1e42bbbd5e4b0abfc6c04e6b
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use the CMSIS NVIC APIs rather than the internal ones
so we can remove them in the future.
Change-Id: I31c2f37bc0aa35668a441f4ef2821b768dd7b817
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove use of __scs structures and defines in place of CMSIS defined
ones. Also, use __ISB() instead of inline asm.
Jira: ZEP-1568
Change-Id: I8798206a12680f6c50105c7c28112632ac9dde50
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have a more generic mcux spi driver that can be used across
multiple Kinetis SoCs, remove the specific k64 spi driver.
Jira: ZEP-1374
Change-Id: Ifc324374f305837f5e3d2cfd7ad30d3608865b5b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux dspi driver to adapt it to the Zephyr
spi interface. Unlike the existing k64 spi driver, this driver can be
used for other Kinetis SoCs that contain the dspi module.
Jira: ZEP-1374
Change-Id: I9417c1513565dfcc47ccda098492f60e840f4f84
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds default configurations for baud rate, transfer word size, clock
polarity and phase. These default configurations can be shared across
multiple spi drivers.
Change-Id: I221b402c075003014991b38f6342a89e55c3bec9
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds Dualtimer support to be used as a Timer.
Jira: ZEP-1300
Change-Id: If13143c8a8bdb07210daca66deca44710a18406f
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds Dualtimer to be used as a counter.
Jira: ZEP-1300
Change-Id: Ic4a2d89ec7fc0c0c2a0bc7f6d32d97637049faaf
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds Timer 0 and 1 to be used as timers.
Jira: ZEP-1300
Change-Id: I57112a8ed6f5daa22345e8807e9ebe87bb09e782
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds clock control to the counters based on Timer 0 and 1.
Jira: ZEP-1300
Change-Id: I14499a833fe9720496ab7905bc1466e9b03bb316
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds a common interface for timers and counters based on
CMSDK APB timers.
Jira: ZEP-1300
Change-Id: I1f89f674d31410f19b651cd904c79f8d173a5357
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The NXP copyright should not have 'Semiconductors, Inc' in it.
Change-Id: I6e290146d49bf22d1d40b7fa764bb53b6b122303
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The commit c90e4d063be0ff5f47df45ca8500eff8518c5d25 changed
line 216 in drivers/gpio/gpio_stm32.c:
-elif CONFIG_SOC_SERIES_STM32F4X
+#elif /* CONFIG_SOC_SERIES_STM32F4X */
This causes the following compiler error:
zephyr/drivers/gpio/gpio_stm32.c:218:39: error: #elif with no expression
#elif /* CONFIG_SOC_SERIES_STM32F4X */
^
Change-Id: Ie8b124931e333aa7860e6db22f5c259670e29833
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Now that we have a more generic mcux serial driver, remove the uart_k20
driver.
Jira: ZEP-719
Change-Id: I51a3237454140feabbfe18ac2c8ee451e572c7be
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux uart driver to adapt it to the Zephyr
serial interface. Unlike the existing (and confusingly-named) uart_k20
driver, this driver can be used for k64 and other Kinetis SoCs.
Implements polling and interrupt-driven serial interface functions that
are logically equivalent to the uart_k20 driver. Adds an extra instance,
irq_tx_empty(), and err_check() that aren't implemented in the uart_k20
driver.
Jira: ZEP-719
Change-Id: Iab99542e7ec921ef4f361437768113fee01e5fe8
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Implementation includes adding some defines in the pinmux,
adjusting gpio driver to specific defines for STM32F3X family,
adding specific functionality in the F3X SoC definition.
Change-Id: I465c66eb93e7afb43166c4585c852e284b0d6e67
Signed-off-by: Adam Podogrocki <adam.podogrocki@rndity.com>
FXOS8700_THREAD_PRIORITY and FXOS8700_THREAD_STACK_SIZE need to also
depend on FXOS8700_TRIGGER, else they will not show in the fxos8700
menu entry when running "make menuconfig".
Change-Id: I8f59125157f046592f3c92dcf2a92bd0e407cd6a
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
The rationale for removing fragments while sending them is to free the
memory they're using as soon as possible. This worked fine because
most protocols implemented initially did not require any
retransmission, so the upper layers were never holding an extra
reference to the buffer (& their fragments).
This is not the case anymore, as the TCP layer holds a reference to
a buffer (& fragments) while confirmation from the peer has not been
received, allowing retransmission.
With this change, the fragments of a buffer are not removed when being
sent by the SLIP layer; however, the buffer is still deferenced when the
transmission is complete. If nothing else holds a reference, all the
fragments are returned to their respective pools, like before.
Change-Id: I74966d72f6970b66f526ea0b765101077c843de2
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
All sample applicatons in Zephyr, using the ENC28J60 driver, set
the ETH_ENC28J60_0_GPIO_PIN Kconfig variable to 19.
However, in the Kconfig.enc28j60 file this variable is set to 24.
That default value, 24, was used only during the first iterations
of this driver and never used again.
In this patch, we set the Kconfig variable to 19 and simplify
project configuration files by removing one line.
Change-Id: I3d5fd9da04a3f10845d2a409de56f5b9c235e995
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This is one of the series of patches that simplifies the driver
code by using the IS_ENABLED macro. This removes the need of the
const variable and the three wrapper functions on semaphore APIs.
Jira: ZEP-1251
Change-Id: I5102e8674663ddbfc65220de72c8b778a9ec726c
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
This is one of the series of patches that simplifies the driver
code by using the IS_ENABLED macro. This removes the need of the
const variable and the three wrapper functions on semaphore APIs.
Jira: ZEP-1251
Change-Id: I2ea0b2d04252d6b28e7d5ca528480234545e6eed
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
There was a recent change to the license boilerplate of the entire
source tree, however as this spi.c was just recently added it missed
the change.
Change-Id: Icc95084a4b051266beaf1796c31d9aec9da538d0
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove an unnecessary condition check in Kconfig.
All the config options already depend on I2C.
Change-Id: Ia8876442652df9f105e862d8c2db394699c81f63
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This driver acts as a pass-through, taking raw HCI data, converting
it to SPI comms and vice versa. It works in the same way as the
existing H:4 and H:5 drivers, only it uses SPI instead of UART.
In this first release, the only BLE board which has been tested is
the X-NUCLEO-IDB05A1:
http://www.st.com/en/ecosystems/x-nucleo-idb05a1.html
Although the current supported SPI format works like the one below,
it should be trivial to adapt it to support other chips with a
different format.
SANITY CHECK = 0x02
SPI WRITE = 0x0A
SPI READ = 0x0B
Tx Format:
[HOST] {SPI WRITE} 0x00 0x00 0x00 0x00 {HCI MESSAGE ...}
[CHIP] {SANITY CHECK} {FLASH SIZE} 0x00 0x00 0x00 {0xFF * MESSAGE LEN}
Rx Format:
{IRQ LINE GOES HIGH}
[HOST] {SPI READ} 0x00 0x00 0x00 0x00 {0xFF * BYTES TO READ}
[CHIP] 0x02 {FLASH SIZE} 0x00 {BYTES TO READ} 0x00 {HCI MESSAGE ...}
Change-Id: I4a00711c922d9ea02c5e2afb0d16715e413b1ed5
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This file doesn't even include <bluetooth/log.h> so any tricks on
BT_DBG are completely pointless (and wrong after the recent update to
the debug logging API).
Change-Id: I1b2b7942a11a4f7229dc35aa2701b3180dc35a28
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The new IS_ENABLED macro allows exposing conditionally enabled code
always to the compiler, even though it may not ultimately end up being
built. This is in particular useful for letting the compiler catch any
logging format string errors. Introduce a new BT_DBG_ENABLED macro
that c-files need to define before including <bluetooth/log.h> in
order to choose whether BT_DBG() logs are enabled or not.
When no Bluetooth logs are enabled the patch also modifies the log
macros to have the format strings checked with the help of the
__printf_like annotation and empty static inline functions.
Change-Id: Ie6bc8e10727b5b306f3ed0f94089a07a22583d9b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the use of the IS_ENABLED macro
(https://gerrit.zephyrproject.org/r/#/c/9882), the driver
reentrancy code is simplified:
The original const variable which used to serve the purpose of
making the build to compile out the reentrancy code when the
reentrancy configuration flag is not enabled is no longer
needed as the use of the IS_ENABLED macro achieves the same result.
Also the original 3 wrapper functions around semaphores API are
not necessary; instead, just use the semaphore API directly.
Jira: ZEP-1251
Change-Id: I23552b77d19044dc94de443018759cb3ec10a52b
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Remove the type field from the sensor value structure. All values will
have the type previously defined by SENSOR_VALUE_TYPE_INT_PLUS_MICRO.
This simplifies the interface, as apps will know what value type to
expect. Apps that prefer to use double values can optain them using the
sensor_value_to_double function.
Change-Id: I3588d74258030eb16c3f89d8eead13cca4606b18
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
tested with blinky, button and disco apps
Change-Id: I4b520d4f3e42c97e4a723747ce4a6c67ca9f1d18
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
riscv-qemu UART:
1) comprises only one register that is used to send or
receive characters in a polling fashion.
2) does not have a FIFO and is not interrupt-driven.
Change-Id: I9408f1776eba4cec4aa203a5da759ec04bcddf1f
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
The riscv-qemu timer driver does not implement
TICKLESS_IDLE
Change-Id: I3eeb5abb05b3f16b55ab9343c2045295b3010cfd
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
The pulpino_timer driver does not implement TICKLESS_IDLE
for the time being.
Change-Id: I0cce8c8a7e203d551a924863462e6c86af4c98ff
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
Add common log level for all IEEE802154 drivers.
Change-Id: If92c96b14e630d4482aadf9cacb25662d6663399
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Force-align all variables defined via asm .word to ensure 4-byte
alignment.
The straddled_tick_on_idle_enter variable was a bool, which resolved in
an one-byte quantity. Changing it to a 32-bit integer. It would have
occupied 4 bytes anyway with alignment.
Fixes ZEP-1549.
Change-Id: If5e0aa1a75dbc73d896b44616f059d221fe191c6
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The k64 pinmux driver was deprecated when the more generic mcux pinmux
driver was added, but it can actually just be removed because it is not
a public interface. Applications should be using the public pinmux API,
not the private k64 pinmux API. There was one case in the net samples
that used the private API which was cleaned up in a previous patch.
Change-Id: I49a6397baa57973930cb63bd2a9883b14f7ddafd
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that we have a more generic mcux gpio driver that can be used across
multiple Kinetis SoCs, remove the specific k64 gpio driver.
Jira: ZEP-1394
Change-Id: I177f96a75e441b70c523e74e99f1b7a54eac6b0e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new mcux gpio driver that can be used for k64 and other Kinetis
SoCs. This driver uses mcux CMSIS register accesses to the GPIO and PORT
modules. Some of the logic from the k64 gpio driver was reused and
refactored (mainly flag parsing and callback handling).
Jira: ZEP-1394
Change-Id: If5e9390861c181ec555dce6569b14debb729526a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Changes the init level for the mcux pinmux driver from POST_KERNEL to
PRE_KERNEL_1. This will allow moving the uart console pins from the k64
soc init to the board pinmux tables.
Change-Id: I6d3377c9a689c12711c84387f74843ca9488df52
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Renames the ksdk random generator shim driver to mcux.
Change-Id: I8bc376937fed3024c809782139a0a72c7332f89a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The ksdk pinmux dev driver was previously merged into the regular ksdk
pinmux driver, and the config PINMUX_DEV_KSDK was removed. Two
references were inadvertantly left behind, so remove them now.
Change-Id: I77394be5459d55a9f16e7bd2b3c9d688c4605b4f
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Merges the ksdk pinmux dev driver into the regular ksdk pinmux driver,
which now exposes the public pinmux API. Removes the private ksdk pinmux
API and converts the frdm_k64f and hexiwear_k64 boards to use the public
pinmux API.
Jira: ZEP-958, ZEP-1432
Change-Id: Ie5f60b604133093050b9c596050cad776d7b7cb3
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
On the nRF5x platforms we need always need the NRF_RTC_TIMER and it
depends on the CLOCK_CONTROL_NRF5. So enable all of these always.
Fixes issues if one tries to build nRF5x platforms w/o CONFIG_BLUETOOTH.
Change-Id: I0f9af785e785f37ec289a935ddf70ee6dec08cd4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove legacy option and use SYS_CLOCK_EXISTS where appropriate.
Change-Id: I3d524ea2776e638683f0196c0cc342359d5d810f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove aio disabling code before calling callback. If aio is
disabled before callback is invoked, calling pending
interrupt check API in the callback will get negative result.
If user wants to disable the aio, it can do this in callback
instead of this being done blindly before callback.
Jira: ZEP-1437
Change-Id: I42ebe4584af6396ac2360152f9b0e2c389c44145
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
drivers/gpio/gpio_pcal9535a.c defines a nano_timer,
but never uses it. So delete it.
gpio_sch.c uses a k_timer, but gpio_sch.h defines a
nano_timer. So change the variable poll_timer to
type k_timer.
Jira: ZEP-1525
Change-Id: I884e4703c1ace61da5be7d9c63e58e7c3bce7f68
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
The sensor_attr_set() wrapper deals with drivers that do not support
the attribute set API, there is no need to provide a per driver
implementation that only return -ENOTSUP.
Change-Id: I1568ab018988fc560bd89ab96f2f2256ddd5b7e1
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
UART 16750 is basically a UART 16550 with a 64-bytes FIFO.
The 64-bytes FIFO can be enabled via register FCR.
Account for it in the uart_ns16550 driver whenever the
CONFIG_UART_NS16750 variable is set.
Change-Id: I2342b28a41d03c96410bbfbe57e4b5a4e335731d
Signed-off-by: Jean-Paul Etienne <fractalclone@gmail.com>
Since RTTWriteNoLock is not thread-safe or preemptable, it is necessary
to lock interrupts around the calls to it.
Change-id: I38b7e37a0f46e77bf82c1e07d549414393e84a51
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since callers of bt_recv() have so far anyway been required to know in
which context to call it (based on e.g. bt_hci_evt_is_prio) it's
cleaner to have two separate APIs: bt_recv and bt_recv_prio.
Change-Id: Icd0d9aed9c51ffd2def31432c4ffcc16a9f13ccd
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use interrupt based transmission instead of polling.
Change-Id: Iebfd67372044d3e6de9bdbdd6f0c9c6d01d46cb9
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
So far the use of k_sem meant that there was no major benefit of
having more than 2 or 3 RX buffers since there was no queuing
mechanism. Instead of using k_sem, introduce a k_fifo and use that to
queue up incoming buffers. This way the RX buffer count can be
increased with measurable effects on throughput.
Change-Id: I8122b233aeee7c8e145de3fff5f10bcfe348efaa
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The H:5 HCI driver doesn't need the type-specific bt_buf allocation
helpers.
Change-Id: Iccb9803f32f3143f1cdf972d9229124816a99aa6
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Completely redesign the H:4 driver to utilize its own thread and
select the new RECV_IS_RX_THREAD Kconfig option.
Jira: ZEP-1483
Change-Id: I0ca0661b66d564e5edc1b8505706d6bb76632e79
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This option has not been used so far and will only contribute
unnecessary complexity in subsequent patches that introduce a concept
of combined RX buffers.
Change-Id: I53e0ce5155eebc352b84ba41b30ecb9d9958699f
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This helps simplify code that was previously combining net_buf_add()
with memcpy().
Change-Id: If44cf9cd651aba5e544e36567869f147468663eb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This moves the shell component into its own subsys and groups all
related files and options into a single place.
Additionally, one Kconfig option will now be required to enable the
shell:
CONFIG_CONSOLE_SHELL=y
The header files was also moved to include/shell/shell.h and can be now
referenced with
#include <shell/shell.h>
instead of
#include <misc/shell.h>
Updated documentation as well.
Change-Id: Iffbba4acfa05408055e9fd28dffa213451351f94
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
replace include <nanokernel.h> with <kernel.h> everywhere and also fix
any remaining mentions of nanokernel.
Keep the legacy samples/tests as is.
Change-Id: Iac48447bd191e83f21a719c69dc26233216d08dc
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Introduce random device API analgous to other device driver classes in
Zephyr. Modify the the KSDK random driver to implement the API.
We retain the sys_rand32_get() interface for now on the assumption it
will eventually relocate to or be otherwise replaced by an entropy
management system.
The existing TEST_RANDOM_GENERATOR related drivers that do not
generate entropy are not modified to expose this driver API since they
cannot generate entropy.
Change-Id: I60b2d5afddf242e802a1d9014c99579870fb7472
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The GPIO_INT_LEVEL value is zero so the mask assignement
is never executed. Using the bit complement GPIO_INT_EDGE
the proper mask is assigned
This issue was reported by Coverity
Coverity-CID: 151966
Change-Id: Iacfeb6466388023bd6123ba86280aa9ca15f34e4
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Not all users are in an ISR context where we can't block, so give the
callers the freedom to choose if they want to block or not.
Jira: ZEP-1481
Change-Id: I19bd7e2df94c4eeb60886a17a78f872bd7bea887
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When CONFIG_SYS_POWER_DEEP_SLEEP is enabled, spi_qmsi_ss will
keep entering deep sleep because it needs to wait until the
current transfer completes, which blocks the current thread.
The system keeps entering deep sleep again and again and the
transfer will never complete.
Add device_busy_set() to spi_qmsi_ss driver to indicate that
the device is busy and block the system from entering deep
sleep during transaction.
Jira: ZEP-1488
Change-Id: I5a4456933249def93eaa529b30b99d730af74482
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
When CONFIG_SYS_POWER_DEEP_SLEEP is enabled, i2c_qmsi_ss will
keep entering deep sleep because it needs to wait until the
current transfer completes, which blocks the current thread.
The system keeps entering deep sleep again and again and the
transfer will never complete.
Add device_busy_set() to i2c_qmsi_ss driver to indicate that
the device is busy and block the system from entering deep
sleep during transaction.
Jira: ZEP-1487
Change-Id: Ia681d242349bce5a9867e54df4e65dba09005930
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
Enable arc to access the i2c controller on I/O fabric.
There are two i2c controllers on quark se SoC. One is attached
to the I/O fabric and the other one is in the sensor system.
X86 cpu is only able to access the i2c controller on the I/O
fabric and the access is supported by existing code. HW allows
arc to access both controllers. But, the existing code only
gives arc access to the controller in the sensor sub-system.
Let's grant arc the access to the controller on I/O fabric as
well by the following changes.
1. Add i2c_qmsi.c into arc compilation.
2. Use the already defined macros to choose interrupt numbers
and do interrupt unmasking automatically based on the
compilation targets.
3. Add new symbols in Kconfig including driver names for both
controllers
Jira: ZEP-1189
Change-Id: I317da6038c50e0c8bd16f446182c1f8bdf6d3ba2
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Enable arc to access the spi controller on I/O fabric.
There are two spi controllers on quark se SoC. One is attached
to the I/O fabric and the other one is in the sensor system.
X86 cpu is only able to access the spi controller on the I/O
fabric and the access is supported by existing code. HW allows
arc to access both controllers. But, the existing code only
gives arc access to the controller in the sensor sub-system.
Let's grant arc the access to the controller on I/O fabric as
well by the following changes.
1. Add spi_qmsi.c into arc compilation.
2. Use the already defined macros to choose interrupt numbers
and do interrupt unmasking automatically based on the
compilation targets.
3. Add new symbols in Kconfig including driver names for both
controllers
Jira: ZEP-1190
Change-Id: I40a5d423d4b7986a897834d1a3831938005eda6f
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Use new kernel header file and k_sleep from unified
kernel instead of nano timer.
Change-Id: I1c98c07f880382eaa87f6e0c45967a4b8b6bfd7d
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
From code inspection, the driver always took timeouts in milliseconds.
The only sub-ms wait uses k_busy_wait(), which has microseconds
granularity, but its granularity does not depend on the system clock
tick rate.
Change-Id: If48363fd1fbeeb8e5ff0f0f2ca86e671d63bc571
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
It receives a timeout in ms, but was still converting it to ticks, while
the unified kernel API takes a value in ms.
Change-Id: I8ff7f44090716385764fe4b2a087043a2e0d70af
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Adds optional support for tap and double tap sensor triggers to the
fxos8700 driver using the pulse detection hardware function.
Default configuration values were taken from NXP AN4072, section 6.3.
http://cache.nxp.com/assets/documents/data/en/application-notes/AN4072.pdf
Change-Id: Ia95091628a853eb956f6fd1df099a9e6e101b707
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The GPIO_INT_LEVEL and GPIO_INT_ACTIVE_LOW values are zero so the
statements are never executed then is better use the bit complement
masks
This issue was reported by Coverity
Coverity-CID: 157586
Change-Id: Ic8b20660a991dd3d0c71248f84c917e5ce5c3c7c
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Remove the existing code that iterates over k_sem_give() and setup the
initial counter directly, take the opportunity to set the maximum count.
Change-Id: Ib91ea263567ff761e4953c142a22a56658efe293
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The shell_cmd structure has three parameters and only two were
initialized. So, this commit initializes the remaining parameter
and also adds the ARG_UNUSED macro to avoid compiler warnings.
Change-Id: I667a4e9839ec5acd526df0bb465beb2062518315
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Remove the unused argument and comparing int to unsigned int
compiler warnings.
Change-Id: Iad79ec2ef8206b2494875a93551a0f47e234ff8d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Use the right data-type to avoid compiler warnings.
Change-Id: I3e807482c5636f37ef1288689450dbe3c9c04dcf
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
This patch adds the ARG_UNUSED macros to some function
arguments to avoid compiler warnings.
Change-Id: I628aea55d98cf8519c046ae5835e95cfa70a973f
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
To support interrupt-based GPIO callbacks in the nRF5x series one needs
to use the GPIOTE module, which has a series of channels that can be
programmed to trigger interrupts on level changes.
This commit adds basic support for the GPIOTE module within the nRF5x
GPIO driver, as well as callback support in order for basic buttons and
switches to work.
Change-Id: I9ae600f894372ad42b09a18cc38a90fc29abb0df
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
To make way for the upcoming blinky and GPIO support for nRF5x-based
boards, this change addresses the hardcoded dependencies in Kconfig
default configurations of the different boards, moving the common option
defaults to the SoC default configuration itself.
Change-Id: I8db0750311ad5a12b76237b39438376f20f6f496
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The pinmux configuration is done during board initialization.
This was validated using the following Zephyr apps:
- samples/basic/blinky
- samples/basic/disco
- samples/basic/button
All 4 GPIO ports are supported.
Change-Id: If8599a23c1d56cfd678a6e2e5339f7e093c6061a
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The new Nordic MDK redefines certain UART signal names for backwards
compatibility with the new nRF52840 IC.
This patch addresses the potential name conflict between the redefined
signals and the existing variable names defined in the UART driver.
JIRA: ZEP-1418
Change-Id: I559d9335d2eeaa0a88d3f261b70508a1c98b989d
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Move logging out of misc/ to its own subsystem. Anything related to
logging and any new logging features or backends could be added here
instead of the generic location in misc/ which is overcrowded with
options that are not related to eachother.
Jira: ZEP-1467
Change-Id: If6a3ea625c3a3562a7a61a0ba5fd7e6ca75518ba
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
rename NANOKERNEL_TICKLESS_IDLE_SUPPORTED to
TICKLESS_IDLE_SUPPORTED and remove nanokernel occurances in Kconfig
files.
Make TICKLESS_IDLE depend on hardware that supports it.
Change-Id: I6a2e4fb0f7cf4b45475b48e71823ea089ee98759
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
PRINTK was conflicting, reanme to DBG.
Jira: ZEP-953
Change-Id: If5d6ef385c5ed223f6f7eae9bde887ae4a1b946a
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
That module is not used anymore: it was introduced pre-Zephyr to add
some kind of awareness when debugging ARM Cortex-M3 code with GDB but
was never really used by anyone. It has bitrotted, and with the recent
move of the tTCS and tNANO data structures to common _kernel and
k_thread, it does not even compile anymore.
Jira: ZEP-1284, ZEP-951
Change-Id: Ic9afed00f4229324fe5d2aa97dc6f1c935953244
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The ethernet controller being a freescale one, let's use its OUI. Then
only 3 bytes are needed for generating the rest of the MAC address.
Also, generating the MAC address in the right order.
Change-Id: Id3346ef44f8c24edc2e23dee6ac0581ac58cf4ff
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Left over from old IP stack it seems.
Change-Id: Ic7ce731b8661294125fa0e0e058570aeff7b97cf
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Such stack size might vary if debug is enabled or not and depending also
on other factors. Let's do the same for priority as well, putting it to
high prio as default (15 is way too low level).
Change-Id: I16afab33895085bacdef087fe70adeb1ae3ca2ab
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
ll_len means link layer length, but it's misleading here as ll_len is
the whole net buffer length: reserved ll length + payload length.
Change-Id: If7ec0fc950245d370fa0f82ae1050b05c11c7b90
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
ETHERNET is a left-over from old and now unavailable IP stack.
Change-Id: I488d9ffcfb1fe3589b522dc2d620873daeb892c8
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Note: This driver need to be ported to new native IP stack in order to
be available again.
Change-Id: I7825c8679e66f8a1d44d75c9d53e9da207b743af
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
At this point, if the frame was accepted by the controller, it means
that CRC was valid. Thus, there is no reason to get it in the buffer.
Let's just pop it out from controller's memory.
Jira: ZEP-1361
Change-Id: Ic8681c77b0afa30583c7fae281db1a89ff97ed2b
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Directly use AON GPIO trigger instead of IPM.
In the past, SW did not allow arc to receive AON GPIO interrupt.
So, interrupt from BMI160 was routed to x86 cpu. Then, x86 cpu
passed the event to arc through IPM. But, SW was updated and arc
is able to directly receive interrupt from AON GPIO now. So, IPM
is not needed any more. Let's remove IPM related code and use
GPIO as the default trigger source.
This change is on top of the bmi160 sample app change to not use
IPM.
Change-Id: I49d8040764d03b24e09d89e66643c020ef63a3c9
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
The nRF RTC driver, which is used a system clock driver due to the lack
of SysTick hardware on the SoC, was using too much CPU time in its
_timer_idle_exit() implementation due to the use of 64-bit arithmetical
operations. This was causing the ISR wrapper to add excessive latency to
critical interrupts, causing BLE controller asserts.
This patch addresses the issue by using exclusively RTC ticks instead of
OS ticks, thus avoiding the necessity to convert during
_timer_idle_exit() calls, which are the most critical to interrupt
latency.
In addition the driver is now able to detect setting tick events in the
past due to it being interrupted by a higher priority context, and will
reschedule and trigger the ISR at the same time.
Change-id: I56a3be96b9fdd554c3650012d647af2f0415eb8a
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
There are static initializer macros available for most kernel objects
which we should use whenever possible.
Change-Id: I496f4d05d26801eddd21fae53bdd4fcdc3246fe3
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When going into DEEP_SLEEP state, the ARC timer
needs to be restored.
This implements the function to restore the timer
after sleep.
As the time spent during sleep is not currently known,
the timer is expired to reschedule the application task.
Jira: ZEP-1224
Change-Id: I22a30d0fd79f177cf166b9a29dc78d68f7d7fbad
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
In order to resume the ARC from deep sleep,
the interrupts need to be restored.
The FIRQ stack needs to be saved and restored
when performing sleep operations.
During early initialization, the sp in the 2nd register bank
is made to refer to _firq_stack.
This allows for the FIRQ handler to use its own stack.
Fast Interrupts cannot be used after sleep if this information
is not restored.
This patch adds the suspend and resume functions.
Jira: ZEP-1223
Change-Id: Ic81980f05aee6c1f7b8c46c743f2648c65b29486
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Move interrupt initialization for the ARC to its own
device. The init function for the arc will be only
doing platform specific operations
Jira: ZEP-1288
Change-Id: Icb04c3622890021c65cd24cecf6cafee6c37caf9
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
In order to keep the initialization process light-weight, remove
net_buf_pool_init() and instead perform the initialization of the pool
and buffers in a "lazy" manner. This means storing more information
in the pool, and removing any 'const' members from net_buf. Since
there are no more const members in net_buf the buffer array can be
declared with __noinit, which further reduces initialization overhead.
Change-Id: Ia126af101c2727c130651b697dcba99d159a1c76
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Restructure the RANDOM Kconfig to match the structure used in other
drivers with a single top level menu. Move the true random number
generators to appear first in the menu, with pseudo generators at the
bottom. Do not present pseudo generators if a true random generator
is presented.
This change implies that tests, samples and applications that require
the random driver interface must now select CONFIG_RANDOM_GENERATOR.
In order for tests and samples to build (and run) on platforms that
have no random driver it remains necessary to select
the CONFIG_TEST_RANDOM_GENERATOR.
Note that CONFIG_TEST_RANDOM_GENERATOR retains its original purpose of
enabling a random driver that delivers non random numbers for the
purpose of testing only.
Change-Id: I2e28e44b4adf800e64a885aefe36a52da8aa455a
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Update drivers to return INT_PLUS_MICRO values instead of doubles.
This hides the fact that the drivers use floating point operations and
doesn't force the application to use them as well.
Change-Id: I14c6faecb35331c2fdbdab41bc624d751de984b8
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Use integers for sensor value calculations in which doubles are not
required.
Change-Id: I8662023ca596cb232e31849b0b77ae2bf0372cf0
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Remove SENSOR_VALUE_TYPE_INT as it is the same as
SENSOR_VALUE_TYPE_INT_PLUS_MICRO with val2 set to 0.
Change-Id: If5a9c579b7267701c27f40fd887acae47d64edc5
Signed-off-by: Bogdan Davidoaia <bogdan.m.davidoaia@intel.com>
Until now it has been necessary to separately define a k_fifo and
an array of buffers when creating net_buf pools. This has been a bit
of an inconvenience as well as blurred the line of what exactly
constitutes the "pool".
This patch removes the NET_BUF_POOL() macro and replaces it with a
NET_BUF_POOL_DEFINE() macro that internally expands into the buffer
array and new net_buf_pool struct with a given name:
NET_BUF_POOL_DEFINE(pool_name, ...);
Having a dedicated context struct for the pool has the added benefit
that we can start moving there net_buf members that have the same
value for all buffers from the same pool. The first such member that
gets moved is the destroy callback, thus shrinking net_buf by four
bytes. Another potential candidate is the user_data_size, however
right not that's left out since it would just leave 2 bytes of padding
in net_buf (i.e. not influence its size). Another common value is
buf->size, however that one is also used by net_buf_simple and can
therefore not be moved.
This patch also splits getting buffers from a FIFO and allocating a
new buffer from a pool into two separate APIs: net_buf_get and
net_buf_alloc, thus simplifying the APIs and their usage. There is no
separate 'reserve_head' parameter anymore when allocating, rather the
user is expected to call net_buf_reserve() afterwards if something
else than 0 headroom is desired.
Change-Id: Id91b1e5c2be2deb1274dde47f5edebfe29af383a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This issue was reported by Coverity
Coverity-CID: 157621
Change-Id: I7f84c0868467ab55e033aecac037967da001a6db
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
Device sync APIs are actually wrappers for semaphores.
Let's replace them with semaphores.
Jira: ZEP-1411
Change-Id: Ic37972a631f0bfd7bc45f28088e1c423151b1612
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Device sync APIs are actually wrappers for semaphores.
Let's replace them with semaphores.
Jira: ZEP-1411
Change-Id: I02c7cba21d21ff9288e452121e3b7ebb7d251bb4
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Device sync APIs are actually wrappers for semaphores.
Let's replace them with semaphores.
Jira: ZEP-1411
Change-Id: I5662057222aec54f02db9d9cdcd7f4f006c6c530
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Use the SYS_INIT() mechanism to invoke the sys_rand32_init() function
in random drivers that require an initializer. Remove all empty
sys_rand32_init() instances.
The existing explicit sys_rand32_init() function runs immediately after
PRE_KERNEL_2 before stack canaries are initialized. In order to get
equivalent behaviour with sys_rand32_init() we set SYS_INIT() to
initialize the random drivers at the lowest priority of PRE_KERNEL_2.
Change-Id: I4521e44daac806bc4eef01ce7fdf2ba5367e0587
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Basic interrupt driven driver for the nRF5 onboard temperature sensor.
Change-Id: Id0ac303293b8e8b8285b19bcda31284ee6617105
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Now that we have a more generic ksdk pinmux driver that can be used
across multiple Kinetis SoCs, deprecate the specific k64 pinmux driver.
Jira: ZEP-1393
Change-Id: I11cfe9a53746a6e85eced2a7cecf0396d42a7a19
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Kinetis SoCs contain one or more PORT modules to handle pin muxing and
pin configuration. Unlike the existing k64 pinmux driver, this driver
handles each PORT module individually and can be used for other Kinetis
SoCs.
This driver uses KSDK CMSIS register accesses to the PORT module rather
than the KSDK PORT driver (fsl_port.h), because the Zephyr pinmux
interface contains both set() and get() functions to access the pin
configuration. The KSDK PORT driver only contains a set() function
(which is a very thin static inline function to modify the PCR
register), therefore building a shim on top of it would result in a
strange mix of using the KSDK PORT driver for the set() and a direct
CMSIS register access for the get().
Jira: ZEP-1393
Change-Id: I2f7c6b08b207350697d590dcd665223f81de9f9e
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
subdir-ccflags-y +=-I${srctree}/subsys/net/ip isn't need so lets
remove it.
Change-Id: I60d97ce25398d7d3801e837075dbf75d1375e055
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
ccflags-y += -I$(srctree)/kernel/unified/include isn't need so lets
remove it.
Change-Id: I910bbac4a189de965d844f5fc36571e8dcb5705d
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We can locally reference the file we need, so don't add a -I we don't
need.
Change-Id: I4d9507d5368073443dcc78a5821fe09d3e0b9bfc
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We can locally reference the files we need, so don't add a -I we
don't need.
Change-Id: I764aea4177a8995489e0f15f71f7373427b43394
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There's now snprintk available that's more light-weight on the stack
than snprintf.
Change-Id: I6b3e4409703ca92fe6b8f4146ff47c490ab826cb
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SYS_LOG macros now map to printk by default, and printk doesn't
(currently) support %2.2x, rather %02x needs to be used instead (it
gives the same result).
Change-Id: I0f7a5b7da91afba0c970bce7e2680de40c917bd3
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix compilation issues that show up if SYS_LOG is mapped to printk
instead of printf. Unlike printf, printk is annotated so that the
compiler catches incorrect format specifiers passed to it.
Change-Id: I4d6f635a0ed61de698727028ea8767dc0ef28bb1
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Provide PWM driver for STM32 series F1/F4/L4.
Driver is ported on STM32Cube HAL and should support other STM32
series with minor updates.
Configuration is done so that PWM sample driver could be run on
all nucleo boards supporting PWM driver.
Change-Id: I6522a565451085df932e0eefd8404268380b5bfe
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add pin config for PWM support on ST Nucleo boards
Following config is chosen:
-PA0/PWM2_CH1 for F401RE and L476RG
-PA8/PWM1_CH2 for F103RB
Change-Id: I013e15ed35360d7777bb24ff94e0830f913a6580
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds Timer 0 and 1 to be used as counters.
Jira: ZEP-1300
Change-Id: I9d8b971d8a3d76eee2f9cc4600e95729d67717a3
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add driver for CMSDK (Cortex-M System Design Kit) APB WDOG. This device
uses NMI as interrupt hence it requires Runtime NMI (CONFIG_RUNTIME_NMI)
to be configured in the platform.
Tested with drivers/watchdog sample application.
Jira: ZEP-1300
Change-Id: Ib318047109af81e32060e80d456ef3873fd380ea
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch enables the clock control interface into the ARM LTD
CMSDK APB UART driver.
Jira: ZEP-1300
Change-Id: Ic0a214beb02d56ffb02ad4e6ca26b80805c0a4e6
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch enables the clock control interface into the ARM LTD
Beetle GPIO driver.
Jira: ZEP-1300
Change-Id: I576767b68a8e4aa965d34716528df3bb4e837d73
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the clock_control implementation for the ARM LTD
Beetle platform.
The main features enabled are:
* Clock on and off in ACTIVE, SLEEP and DEEPSLEEP mode.
* PLL support (freq: 12, 36, 48 Mhz).
The integration with the existing drivers will be done in future
patches.
Jira: ZEP-1300
Change-Id: I07cb2325275bd86a036e8e24aeb7bbf2c6176a93
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add board support for the Nucleo64 L476RG development board.
Change-Id: Ibb5424bc936c67a5d96855617202136d7dea772c
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the I2C for the STM32Lx series
Change-Id: Id1694aeb3606b4fa9772bfb7a9f60e48a7cc93a8
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add all possible pin assignment definitions for I2C{1-3} on STM32L4xx.
Change-Id: I2d4266bc3bb9ba41b74a80567c0b04a89963753e
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add macro for all the available pinmux for the USARTs present on
STM32L4.
Change-Id: Ie4352750e1c6f08642b3e222b57f2a791f08ef74
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add EXTI support for the STM32l4XX family.
Change-Id: Ia92f26eaf49899ea23fae05dd3a7357007c9db20
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the support for all the GPIO port of the L4.
Change-Id: Id365e17223cd5c49443df9fb6b96a3c4f204f523
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the clock driver for the STM32L4 series.
Change-Id: Icdf79061f163d8d00187b382d1564422fb875c5b
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Deal with STM32L4X additions for clock and interrupt handling to the
uart driver.
Change-Id: I6e8dafb132dafea54b8f31a3a5cb6e35a207574d
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There was a misalignment between Zephyr UART device numbering and
SoC UART IP. Device "UART_1" was mapped to IP USART_2, which could
be confusing for user.
This commit allows to align "UART_1" to IP USART_1.
Change is propagated to all STM32F103RB/STM32F401RE based boards and
respective pinmux drivers
Change-Id: Ia8099dfeec7b9c0c686c2a58ccb4dbb1a55b6537
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32Cube based implementation allows single driver file for
all stm32 based SoCs.
By maximizing code reuse, use of STM32Cube eases new SoCs
porting into Zephyr and provides better maintanability and
maturity.
Change-Id: Ief4b723add3dfc8b2a839683559c5a4c5d5eb837
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit replaces the nanokernel.h include by kernel.h.
Change-Id: Ib42fbf2d9f77a73c0831f569b3dbbfb342ea2e1d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
Adds general sensor triggering support to the fxos8700 driver, including
options for the driver to use its own thread or the global workqueue
thread to handle sensor interrupts. Adds specific support to handle the
data ready sensor trigger.
Jira: ZEP-1395
Change-Id: I092f22e35747b92a88eb71a3d162a4fc16227b45
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch fixes RX overflow error in the k64 SPI driver.
Jira: ZEP-1351
Jira: ZEP-1352
Several circumstances lead to an RX overflow:
The RFOF_RE (RX fifo overflow) must not be set as default.
The flag is only set when rx_buf is available. Also it must
be checked inside spi_k64_isr whether RFOF_RE has been set or not.
If the rx_buf is not available and the incoming data
should be ignored, then MCR_ROOE need to be set.
Since it is not possible to change the MCR register
during the transfer, RX fifo must be emptied
if rx_buf_len < tx_buf_len.
The driver also uses spi_data.xfer_len now,
the variable was already defined. Now, transfers are also
possible if tx_buf_len < rx_buf_len (e.g. read slave device register).
spi_k64_push_data has been adjusted accordingly.
The patch simplifies the handling of interrupts.
The interrupts are also switched off in the event of an error.
The patch also fixes a few coding style issues.
Change-Id: I6ce81f595bb1edbbf2253b6595602896ca652762
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Remove non existent CONFIG_SPI_DEBUG and replace cnt
with DBG_COUNTER_* macros.
Jira: ZEP-1351
Jira: ZEP-1352
Change-Id: I1fba7aaead1ad0b36297b069e5a83e25b7991588
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Clear RX and TX FIFO before starting transfer fixing RX overflow issue
on FRDM K64F board.
Change-Id: I9345a0058a6c7958a6ecf3dc23b99fe7bff18796
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Logging in spi_k64 driver is based on printf-like functions and does
not make sense with syslog which adds additional information like
function name and new line already.
Change-Id: I84a81ebf5c3cc94b311a2e41bdb5f014432d2b09
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Use configured init priority same way it is used for other SPI
drivers. Default priority initializes SPI before console hiding
possible errors and debug messages.
Change-Id: Iddc9c783290d852caa8a9385de4ab114f8f7a2e3
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Fixes following error:
...
drivers/spi/spi_k64.c:717:86: error: 'cnt' undeclared (first use in
this function)
...
Change-Id: If49fa4838265cd39a6f72eb265388ff7faae9a9e
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The Real Time Terminal functionality of the Segger J-Link
debug probe and software suite allows applications to write
to a certain RAM area that is read in real-time by the
debugger. This is specially useful when a UART is not
available to provide a console.
This commit adds a console driver that outputs over an RTT
"connection".
Change-Id: Ifce8020060e9f519a61f3f1fbe9f56f98da2ef7f
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add function return value check. This was caught by
Coverity.
Coverity-CID: 157124
Change-Id: I93b23325d657dc787300908b9117b6976617fdba
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Fibers do not exist anymore in unified kernel.
Also, let's just use that option directly so removing the internal
define which is then useless.
Change-Id: I1179d84401934b339d3a9ccd12f6145a120bcb2f
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Other driver than QMSI might have this limitation. Let's wait for a
future rework of SPI API to properly fix that.
Change-Id: Ibad382ce86e7479961b275c4851abf88ed581023
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Currently it's only possible to configure those GPIOs through
boards.<h/c> files and thus it's not relevant for board that do not
embed cc2520 but might get one wired to it, unlike
quark_se_c1000_devboard which directly embeds one cc2520.
Change-Id: I819bc1d2de707ea12eb70dc60a40b28f92666e51
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
* Moved networking code into subsys/net.
* Renamed net/yaip to net/ip at the same time.
* Fixed the tests/net to compile
* Fixed the Makefiles and Kconfig files in subsys/net
to use the new location of the IP stack
Change-Id: Ie45d9e8cb45a93fefdf969b20a81e3b1d3c16355
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The cc2520 driver RX thread did not like the stack information
collection macros defined in net_core.h. Both the cc2520 TX and
RX got the same variable name which did not compile.
This is now changed so that the first parameter is added to
the variable name to create a unique variable.
Change-Id: Ia41d01a71afd73af2ef31aa5f7a890a3cf0385aa
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the native IP stack is now the default, there is no need
for corresponding Kconfig option.
Change-Id: I08e4992f540f928a2b7378e8803e634e38725348
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit removes the legacy Contiki based uIP stack.
The new native IP stack must be used after this commit.
The commit also removes following things:
- legacy cc2520 driver
- legacy ethernet drivers
- legacy IP stack samples
and changes these things:
- disabled tests that only work for legacy IP stack
- select new IP stack by default
- enable random number generator by default as it is needed
by the new IP stack
Change-Id: I1229f9960a4c6654e9ccc6dac14a7efb9394e45d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The default kernel init priority is too low. Make this
configurable and set the default priority so that the
ethernet driver is started just before the network stack.
This commit adds generic ethernet priority and changes
currently available ethernet drivers to use it.
Change-Id: If695e52b6dd9ea227f10ba306bb145d72d2312b0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Refactor code to exit earlier in case of error.
Change-Id: I9ff893f923ff877d69b0e985bb6e4159504e67cd
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
