QEMU Cortex-A53 is the default (and only) board for this architecture,
as such we should enable default testing.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
In the bootloader code, there is a mis-used logical operator
which should be bitwise operator. So fix it.
Fixes#22651
Coverity-CID: 208198
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There is a blue LED used to display connectivity for the SparkFun
SARA-R4 shield. This LED is connected to the modem via GPIO 16
which is the default used by SARA-R4 driver when
CONFIG_MODEM_UBLOX_SARA_R4_NET_STATUS is enabled.
Signed-off-by: Michael Scott <mike@foundries.io>
When running in qemu we utilize fdt-single_arch-zcu102-arm.dtb to
configure qemu. The current dtb requests just under 2G of memory in the
simulation, but we don't really need this and it impacts running on low
memory VMs.
So remove DDR ddr_bank2 and reduce ddr_bank1_3 from 1G - 256K to
128M - 256K in size.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Commit 9987c2e2f9 spills SoC configs
into architecture files which is less desirable. This provides
the jump address for bootloader, and modifies the bootloader to
jump to __start defined in reset-vector.S. This prepares for
that commit to be reverted.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Both memctl_default.S and memerror-vector.S (inside
arch/xtensa/core/startup) refer to XCHAL_CACHE_MEMCTL_DEFAULT which
is not defined anywhere. The linker script for intel_apl_adsp SoC
provides default values, but not the bootloader linker script. So
provide the same default value in the bootloader linker script as
in the SoC linker script.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
- added CONFIG_X86_64 since ACRN hypervisor supports x86_64 capable
platforms only.
- removed CONFIG_SET_GDT: Zephyr doesn't support it in x86_64, and ACRN
doesn't require the guests to setup GDT during boot time.
- added CONFIG_X2APIC, which is preferred by ACRN, which makes it
possible to pass through local APIC to the guests.
Signed-off-by: Zide Chen <zide.chen@intel.com>
Add STM32 CRYP driver support and a corresponding build-only test to
the crypto sample project.
Signed-off-by: Markus Fuchs <markus.fuchs@de.sauter-bc.com>
The Kconfig board choice only has only one option which is implicitly
enabled, therefore it is not necessary to set the symbol explicitly in
board defconfigs.
mimxrt10{50,60}_evk boards are excluded from this change because they
have multiple board configurations (e.g., hyperflash vs. qspi) in the
board choice.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The Kconfig board choice only has only one option which is implicitly
enabled, therefore it is not necessary to set the symbol explicitly in
board defconfigs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The board ships with a write protected bootloader so the flash base
address was artifically adjusted to skip that bootloader. With commit
018bf777e7:
boards: arm: Make Adafruit boards use their DT-defined code partion.
We shouldn't need to artifically adjust the flash anymore. So remove
this, nice side effect is it fixes a dts compile warning.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove unneeded tag bluetooth. Those tests and samples use (should use)
depends_on: ble or whitelist platforms.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Fix the following device tree warnings:
unit-address and first reg (0x20000) don't match for iccm@0
unit-address and first reg (0x80010000) don't match for dccm@80000000
Since the em_starterkit_em7d_normal has a different base address for
iccm & dccm, and most of the em_starterkit variants have different sizes
for iccm & dccm. Just define the nodes in the specific
em_starterkit*.dts file and remove them from emsk.dtsi. This removes
the issue reported in the warning.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the following device tree warnings:
unit-address and first reg (0x40000) don't match for iccm@0
unit-address and first reg (0x80040000) don't match for dccm@80000000
Re-work iccm and dccm reg address and size to be based on #defines.
This allows the nsim_sem_normal.dts to override defaults that are set in
nsim.dtsi. Utilize DT_ADDR macro to take a 'unit-address' still value
and convert it into a hex value (just prepending 0x).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix warnings of the following form:
unit-address and first reg (0x30000) don't match for partition@10000
unit-address and first reg (0x200000) don't match for partition@1F0000
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
ADC_1 peripheral instance was enabled by default in driver.
This is not the usual way to enable peripheral instances, as it
makes board configuration unclear.
Move activation in boards that are declaring ADC support.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
LPC SoCs share the same register for all GPIO poarts. This leads us to a
device tree configuration that missmatches GPIO register address and
GPIO port identifier.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
CONFIG_BOARD_FOO is enabled in a number of board *_defconfig files
although it is useless as it is set by default (as defined as a
one option choice, symbol defaults to 'y').
CONFIG_BOARD_FOO should remain only in target that are defined
in boards providing multiple choices (dual cores, board with multiple
revisions).
Clean it from STM32 impacted boards.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds scripts which downloads the firmware and extracts the
trace messages. The scripts required the SOF diagnostics driver
installed.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Add a command-line frontend to match the logging backend for Intel
Apollolake-based boards like the Audio DSP in the Up Squared.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Create a board definition for the Audio DSP found on the Up Squared
board.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This API will be deprecated in favor of the new API that clearly
specifies whether it works on logical or physical levels.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the non-deprecated flags and configure the modem power switch as
active-low. The UBLOX_PWR_DETECT signal appears to be active high.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update the lora/sx1276 driver to the new GPIO API, using configured
active level and the replacement interrupt and active-sensitive set
APIs.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Convert to the new GPIO API using logical access, including setting the
GPIO line as active low in the Device Tree source.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update bluetooth hcp_spi sample to new GPIO API.
Following changes have been done:
- Use new gpio api functions
- Introduce define for dt generated gpio flags
- Update 96b_carbon_nrf51.dts according to new bindings
- Gpio IRQ pin is configured to output inactive
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the flags included in the new GPIO API to describe the properties of
LEDs and buttons in the device tree source files.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update devicetree sources and bindings, switch to new GPIO API. Use
devicetree property name to identify interrupt signal.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the GPIO_ACTIVE_LOW to signal that the button pins are active low,
instead of the deprecated GPIO_INT_ACTIVE_LOW.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Converts the sdhc spi driver to the new gpio api. Updates device trees
for the olimexino_stm32 and nrf52840_blip boards to set appropriate
active high/low polarity for the spi chip select pin.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts the fxas21002 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on the hexiwear_k64 board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update bluetooth hcp spi driver to new GPIO API.
Following changes have been done:
- Use new gpio api functions
- Get reset, irq and cs flags from dt defines
- Define reset pin as active low and invert set/unset logic.
Tested on disco_l475_iot1 and 96b_carbon.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts the usdhc driver to the new gpio api. Updates the
device tree for the mimxrt1050_evk board to set appropriate active
high/low polarity for the power and card detect pins.
Note that the driver doesn't actually support interrupts yet. It
initializes a gpio callback for the card detect pin, but never actually
enables the gpio interrupt. This incomplete behavior is left as-is,
since the purpose of this patch is only to convert the driver to the new
gpio api, not to add new features.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
For this board all 16 pins on the SX1509B should be configured as
outputs. Six of them are active-low LEDs. Provide configuration so
those six are initialized to output high, and the remainder to output
low.
Two of the pins control the behavior of the CCS811 gas sensor. By
driving them low on boot the baseline current draw of the board is
reduced by 100 uA.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
In initialization code, pairs of gpio_pin_configure/gpio_pin_write are
replaced with calls to gpio_pin_configure that configure a given pin as
output with the proper initial state.
dts file for the board is also updated with the new GPIO flags.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In initialization code, pairs of gpio_pin_configure/gpio_pin_write are
replaced with calls to gpio_pin_configure that configure a given pin as
output with the proper initial state.
dts file for the board is also updated with the new GPIO flags.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Provide correct active level and pull on all signals. Use
init-to-active when configuring antenna switch.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Mark the INT signal to be active low and use the new functions to get
gpio state and configure the gpio interrupt flanks.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
Update the code configuring pins that control the routing of certain
lines on the board, to take advantage of the introduced possibility
of configuring a pin as output with specified initial state.
Additionally, use `gpio_pin_get_raw` instead of `gpio_pin_get` for
checking the reset pin state, to save a few bytes in flash.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Correct DRDY active level to default active-high, switch to new
interrupt configuration.
Also fix a common bug where an already-active DRDY signal is not
properly handled.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
- Updates gpio driver and device tree files to the new GPIO Config flags
- Implements the new port_* APIs
- Update I2C and PWM Drivers to use new GPIO config
- Add esp32.overlay to gpio_basic_api test
- refactor convert_int_type, regs struct
- remove config_polarity
- add kConfig notes
Tests:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_basic_api
- tests/drivers/gpio/gpio_api_1pin
Board:
- esp32 DevKitC V4
Note about interrupts:
The ESP32 requires specifying a CPU interrupt to be used for GPIO
interrupt signals. CPU interrupts can be either level or edge (or
special) triggered, but not both.
Please check gpio/Kconfig.esp32 for more info.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Updates the rv32m1 gpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Assumes the gpio api layer handles translating logical flags to physical
flags.
Stops quietly reconfiguring pinmuxes to gpio mode. The pinmux must now
be configured explicitly in the board's pinmux.c or in the application.
Tested with:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_api_1pin
On boards:
- rv32m1_vega_ri5cy
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use standard spelling for pull and active flags. Correct LED active
level (based on SAM-D21-Xplained-Pro).
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
LPC54114 to use D0 and D1 pinout.
LPC55S69 to use A0 and A1 pinout.
Pins enabled to be used as GPIO for 2 pin test gpio_basic_api.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Updates the mcux lpc driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle functions recently added to the gpio api.
ISR functions to be added later.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Updates the imx gpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Assumes the gpio api layer handles translating logical flags to physical
flags.
Tested with:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_api_1pin
- tests/drivers/gpio/gpio_basic_api
On boards:
- udoo_neo_full_m4
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Updates the mcux igpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Assumes the gpio api layer handles translating logical flags to physical
flags.
Removes port configuration support since that feature is deprecated in
the new gpio api.
Tested with:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_api_1pin
On boards:
- mimxrt1015_evk
- mimxrt1020_evk
- mimxrt1050_evk
- mimxrt1060_evk
- mimxrt1064_evk
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Updates the cc13x2/cc26x2 gpio driver and all associated boards to use
new device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Tested with:
samples/basic/blinky
samples/basic/button
tests/drivers/gpio/gpio_api_1pin
tests/drivers/gpio/gpio_basic_api
On board:
cc1352r1_launchxl
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Updates the cc32xx gpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Tested with:
samples/basic/blinky
samples/basic/button
tests/drivers/gpio/gpio_api_1pin
tests/drivers/gpio/gpio_basic_api
On boards:
cc3220sf_launchxl
cc3235sf_launchxl
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API.
Tested on external SX1509B breakout board and Thingy:52.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on frdm_k64f board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on nrf52840_pca10056 board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on sam_e70_xplained board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Tested on efr32_slwstk6061a board.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This board enabled the IEEE802154_RF2XX driver unconditionally. Instead
make it depend on the IEEE802154 subsystem being enabled.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Move conditionals that depend on USB to Kconfig.defconfig so that unmet
dependencies don't issue a warning.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The symbol SPI_SAME70_PORT_0_PIN_CS3 was defined without a type.
A non-whitelisted Kconfig warning is generated which results on a
configuration error. This associate the bool type to symbol.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
A bug under investigation (issue #22078) limits board operations
to 16MHz. When running at 32MHz, some applications may crash.
In order to enable use of nucleo_l152re with mot of applications,
limit frequency to 16MHz until bug is fixed.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit adds the following:
- EFR32FG1P SoC support for the watchdog
- efr32_slwstk6061a board support for the watchdog
Signed-off-by: Oane Kingma <o.kingma@interay.com>
This commit adds the following:
- EFR32MG SoC support for the watchdog
- efr32mg_sltb004a board support for the watchdog
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
This commit adds the following:
- device tree bindings for Gecko watchdog driver
- EFM32PG SOC support for the watchdog driver
- EFM32PG board support for the watchdog driver
- DTS aliases for testing with default watchdog driver test
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Define a binding for a voltage divider circuit with one or more analog
input channels. Add devicetree nodes for several boards that have
battery voltage measurement support.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Adds device tree nodes and configures Kconfig defaults for the ft5336
touch panel driver on mimxrt10{50,60,64}_evk boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enable the shared IRQ for the UART line and enable the remaining tasks
that depends on a separated declaration of the TX/RX/Err/... IRQs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The cmsis_rtos tests are failing because the stack size used by CMSIS is
too small. Customize the stack size for the aarch64 architecture and
re-enable the tests.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
We need a slightly bigger stack to be able to successfully pass the
logging test. Fix the stack size and enable back the test.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Prepare for a day when all boards specify the chip select in the bus
devicetree node by making sure that the devicetree node associated
with arduino_spi uses the standard D10 pin from the arduino header as
the cs-gpios property value.
Also update the arduino tags in the board yaml files.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This adds support for the Atmel SAM E54 Xplained Pro Evaluation Kit.
Only basic functionality has been tested so far.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
By default the firmware is compiled for the EFM32PG12B SoC with the ARM
Cortex-M4F core. When building for efm32pg_stk3402a_jg, The firmware is
compiled for the EFM32JG12B SoC with the ARM Cortex-M3 core.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Most JEDEC NOR flash devices uses not only typical SPI mode
(MISO,MOSI,SCK and CS), but also QSPI mode (IO0,IO1,IO2,IO3,SCK and CS).
QSPI mode uses more data lines and as a result provide higher
throughput. If this were not enough, Nordic chips provide
hardware acceleration for read/write/erase functions, what
gives significant performance boost.
It does a lot of things "behind the scene", i.e when user has written
some data to the flash and would like to read them back, it has to wait
until the flash is ready by reading WIP bit in Status Register.
This driver does it automatically.
Signed-off-by: Kamil Lazowski <Kamil.Lazowski@nordicsemi.no>
Update the hal_nordic module revision, to switch to nrfx 2.1.0.
Because the list of peripherals for nRF5340 has changed as follows:
- SPIM2 has been renamed to SPIM4
- SPIM2-3, SPIS2-3, TWIM2-3, TWIS2-3, and UARTE2-3 have been added
a couple of related corrections needed to be applied in dts and Kconfig
files, plus the spi_nrfx_spim driver has been extended with the support
for SPIM4.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
There is no such thing as CAVS DMA IP block, the DMA IP block found on
CAVS based chips is made with DesignWare one.
This will help to centralize DW based DMA device into one driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The samd20 does not have hardware support for controlling the SS pin.
Declare a cs-gpio to be able to use the SS pin for samd20 xplained pro
board.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Adafruit Feather M0 and Adafruit Trinket M0 boards aren't set up
to use their defined flash partition table to generate the 0x2000
flash offset for code. This should be enabled by default as the
boards ship with a write-protected bootloader and code should be
flashed where it expected by default.
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
Flashing stm32wb SoCs is available since Zephyr SDK-0.11.0.
Enables it on nuclmeo_wb55rg and set it as default as it is
faster in flashing and support doesn't require additional
action (vs pyocd package support).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit introduces the can-primary alias to identify
the primary CAN interface.
This alias is used for all samples and tests, so they don't
need to probe the right interface.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The CONFIG_ prefixes were missing on these.
Found with a work-in-progress scripts/kconfig/lint.py check.
This symbol is defined in kernel/Kconfig.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
I2C interrupts usage should be the preferred way. This commit
enables them by default in the STM32 I2C driver itself.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Same deal as in commit 677f1e6 ("config: Turn pointless/confusing
'menuconfig's into 'config's"), for a newly-introduced stuff.
Also clean up headers to be consistent with recent cleanups.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
During the first real test of my manual by another developer,
I found out that it would be better to update sequence of events.
Also found out misprints, and some actions was not so obvious.
Corrected manual to be more green developers friendly.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Add the user button to the device tree of nucleo_l452re board.
This button is wire to the pin PC13 of STM32L452
Signed-off-by: Julien D'ascenzio <julien.dascenzio@paratronic.fr>
This commit adds initial support for the Silicon Labs EFM32
Giant Gecko GG11 StarterKit.
Features supported for now are NVIC, SysTick, GPIO, Flash,
Counter, I2C, UART and Ethernet. Support for Watchdog and
ADC will follow as soon as their respective PRs are merged.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Extend `qemu_x86` board configuration with `ieee802154` capability, to
allow it to execute `ieee802154` tests.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
nrf52811_pca10056 board should enable nRF 802.15.4 radio driver
automatically when 802.15.4 subsystem is enabled, as other Nordic
802.15.4-compliant boards do.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Replaced NFFS mentions by LittleFS in all <board>.dts comments
to storage partitions.
Replaced NFFS by LittleFS in a few boards documentation.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Remove link board can, shield was discontinued in
prototype status and will be replaced by a successor.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
...instead of kconfig.
This provides a bit more flexibility in defining driver
instances. Also, since the DTS defines 5 I2C controllers,
the driver code is extended to cover all 5 if the controllers
are enabled.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The I2C controllers on the MEC1501 SoC can be attached to
different I2C output line. For example, the I2C #0 controller
can be used with I2C7 physical lines out of SoC. The output
selection is done by the attribute "port_sel". This renames
the parent I2C nodes on the SoC side to refer to
the controller themselves instead of the output lines to
avoid confusion. The labels of these nodes are also renamed
to reflect the controllers.
On the board level, the DTS labels are overwritten to indicate
the actual output lines.
Aliases are also provided in both SoC and board levels to
provide shortcuts to the DTS nodes.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The SoC, driver, and board support for the CC2650 and CC2650 Sensortag
aren't currently supported and we are removing them as such. If anyone
is interesting in supporting this platform we can easily recovery it
from git.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implement a set of per-cpu trampoline stacks which all
interrupts and exceptions will initially land on, and also
as an intermediate stack for privilege changes as we need
some stack space to swap page tables.
Set up the special trampoline page which contains all the
trampoline stacks, TSS, and GDT. This page needs to be
present in the user page tables or interrupts don't work.
CPU exceptions, with KPTI turned on, are treated as interrupts
and not traps so that we have IRQs locked on exception entry.
Add some additional macros for defining IDT entries.
Add special handling of locore text/rodata sections when
creating user mode page tables on x86-64.
Restore qemu_x86_64 to use KPTI, and remove restrictions on
enabling user mode on x86-64.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
generated_dts_board.h is pretty redundant and confusing as a name. Call
it devicetree.h instead.
dts.h would be another option, but DTS stands for "devicetree source"
and is the source code format, so it's a bit confusing too.
The replacement was done by grepping for 'generated_dts_board' and
'GENERATED_DTS_BOARD'.
Two build diagram and input-output SVG files were updated as well, along
with misc. documentation.
hal_ti, mcuboot, and ci-tools updates are included too, in the west.yml
update.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
HAS_SEGGER_RTT is assigned by various Nordic boards, but assignments
have no effect on promptless symbols. This symbol is enabled through
being select'ed by SOC_SERIES_NRF52X.
Holyiot, nRF52833-PCA10100, nRF52840-PCA10056, and nRF52-PCA10040 only
assign HAS_SEGGER_RTT without assigning USE_SEGGER_RTT. They probably
meant to enable USE_SEGGER_RTT, so do that instead.
Also add a help text to HAS_SEGGER_RTT and a warning re. HAS_SEGGER_RTT
vs. USE_SEGGER_RTT to the documentation.
Flagged by https://github.com/zephyrproject-rtos/zephyr/pull/20742.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Error in that manual.
Header JP39 should have connected jumpers 1-2, 3-4.
In docs I wrote that is to make sure JP39 does not have any jumper.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Added dts additions for stm32 nucleo f767zi board, also added
and modified soc addtions for thet board.
Updated dts reference file name.
Updated yaml to take out adc for now.
Signed-off-by: Roland Ma <rolandma@yahoo.com>
Assignments to promptless symbols have no effect. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
From looking at
http://www.mouser.com
/catalog/specsheets/CircuitCO_595-MINNOWMAX-DUAL%20Data%20Sheet.pdf
, this board uses an Intel Atom E3815 or an Intel Atom E3825 CPU.
Both of those CPUs are listed as vulnerable to all three variants of
Meltdown and Spectre in
https://www.techarp.com/guides/complete-meltdown-spectre-cpu-list/6/.
All the X86_NO_SPECTRE_V* symbols default to n (and it seems nothing
turns them on at the moment), so just remove the assignment, which will
be a no-op.
Also remove the comment re. Spectre V4, as it seems this board is
vulnerable to more than that, though I could've missed something.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Flashing board nucleo_f207zg requires additional instructions
to be provided to openocd in order to enable flashing without holding
the reset button.
Update nucleo_f207zg openocd config to provide requested instructions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We need to include soc.h in nrf5340_cpunet_reset.c, to include
the nRF5340 device headers. Fixes a compilation error when we
build with CONFIG_ARM_MPU=n.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add reference to wpanusb and wpan_serial examples. This links user with
some IEEE 802.15.4 applications.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is (always) selected, in
soc/arm/ti_simplelink/cc32xx/Kconfig.soc.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is selected by the SOC_SERIES_CC13X2_CC26X2,
SOC_SERIES_CC2650, SOC_SERIES_CC32XX, and SOC_SERIES_MSP432P4XX symbols.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is selected by the SOC_SERIES_EFM32HG,
SOC_SERIES_EFM32PG12B, SOC_SERIES_EFM32WG, SOC_SERIES_EFR32FG1P, and
SOC_SERIES_EFR32MG12P symbols.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
We have some races causing random failures with this platform, set cpu
number to one while we investigate and fix the issue.
Related to #21317
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is selected by SOC_SERIES_PSOC62, in
soc/arm/cypress/psoc6/Kconfig.series.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being select'ed by other symbols.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being selected by SOC_SERIES_SAM3X,
SOC_SERIES_SAM4S, and SOC_SERIES_SAME70.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being selected by SOC_MSP432P401R, in
soc/arm/ti_simplelink/msp432p4xx/Kconfig.soc.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being selected by other symbols.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being selected by SOC_ATOM in
soc/x86/atom/Kconfig.soc.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This shield adds analog and digital sensors to a TI LaunchPad
development kit. Currently only the ADXL362 accelerometer is supported.
This is useful for exercising the SPI interface. The analog sensors will
be useful if we add support for the sensor controller and ADC in the
future.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Add BoosterPack connector information to the DTS of the CC1352 and
CC26x2 LaunchPad boards. This allows shields (e.g. BoosterPacks) to use
aliases for the connector interfaces and mappings for the GPIOs. This is
similar to what is being done for the Arduino connectors.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being select'ed by SOC_SERIES_IMX_6X_M4,
SOC_SERIES_IMX7_M4, and SOC_SERIES_IMX_RT.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
These configuration files all enable UART_CONSOLE, which selects
CONSOLE_HAS_DRIVER.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Segger offers J-Link firmware for the debug MCU on the BBC micro:bit.
If this firmware is installed, it allows programming via nrfjprog and
JLink. Add support for this in the board.cmake.
Leave the default at pyocd, to support the factory-programmed
firmware.
With this patch, users who have installed the JLink firmware can flash
this board with nrfjprog using:
$ west flash -r nrfjprog
And can flash or debug with jlink using:
$ west flash -r jlink
$ west debug -r jlink
As usual with runner overrides, you can omit the '-r {nrfjprog,jlink}'
if BOARD_FLASH_RUNNER as a CMake variable is set to nrfjprog or
BOARD_DEBUG_RUNNER is set to jlink.
For more details on this Segger firmware, see:
https://www.segger.com/products/debug-probes/j-link/models/other-j-links/bbc-microbit-j-link-upgrade/
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
KPTI is still work-in-progress on x86_64. Don't allow
user mode to be enabled unless the SOC/board configuration
indicates that the CPU in use is invulnerable to meltdown
attacks.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Assignments have no effect on promptless symbols. Flagged by
https://github.com/zephyrproject-rtos/zephyr/pull/20742.
This symbol is enabled through being select'ed.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all lpc socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all i.mx 6/7 socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all i.mx rt socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adding Kconfig settings to warn anyone trying to build for this
platform of its pending deprecation in 2.2.0.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The DT_INST_* defines for the PWM controllers enabled in the device
tree are always defined causing the LED pins to always be set as PWM
outputs in the pinmux. Revert to using CONFIG_PWM_* for pinmux
configuration for now.
This reverts commit eb42a24dc6.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Defines device tree aliases for on-chip peripherals at the soc level
instead of the board level for all kinetis socs. The eliminates some
duplicate code in the board level device trees, and will allow drivers
to use device-tree generated macros directly instead of through dts
fixups.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add SPI CS GPIO line to reel_board device tree. This is needed to make
the board work with Arduino SPI compatible shields.
Tested on reel_board (1507.1) and reel_board_v2 (1507.2).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
We move the SRAM partition that is used as shared memory with
the Network MCU to the upper part of the Application MCU
memory. In this case we can allocate all lower SRAM to the
application, if we are building a Zephyr image without
support for Trusted Execution.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
With this commit we introduce SRAM partitioning for nRF5340
Application MCU. We define fixed partitions for the Secure
and the Non-Secure images, when building with trusted
execution environment enabled (Secure and Non-Secure images).
For (Secure image) builds without trusted execution environment
enabled we now allocate all available Application MCU SRAM into
the single image, except for the SRAM being used as shared memory
with the Network MCU.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The virtual COM port of the STlink in the Nucleo board is connected to
LPUART1, but the board was configured to use UART1 instead. For this
reason, hello world sample did not work.
In addition to that, PA2 was assigned to both LPUART1 and UART2. UART2
TX is now muxed to PA14.
Signed-off-by: Martin Jaeger <17674105+martinjaeger@users.noreply.github.com>
On nucleo_g071rb, flashing using pyocd requested to hold reset button
during flashing operation.
Using newly available pyocd arguments this is no more needed and
nucleo_g071rb can now be flashed in a fully automated way.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit adds support for the on-board flash MX25R8035F that is
directly connected to the efr32fg soc.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
This commit adds support for the on-board flash MX25R8035F that is
directly connected to the efr32mg soc.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Add board support files for mimxrt1010_evk, the development board for
i.MXRT1010 (CM7) SoC.
- Add pinmux, dts and doc.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
EEPROM simulator and native_posix have been unified to one solution,
the old eeprom,native_posix is removed.
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Add support for a eeprom simulator. The PR limits the addition to
qemu_x86 but it can easily be added to other devices by defining the
eeprom simulator in the dts and setting 'CONFIG_EEPROM_SIMULATOR=y'
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add shield definition for the Texas Instruments LMP90100 Sensor Analog
Frontend (AFE) Evaluation Board (EVB).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for specifying PWM flags for the NXP Kinetis FlexTimer
(FTM) PWM driver through the device tree.
All in-tree clients of this PWM controller are active-low LEDs.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The SRAM address and size are currently available as both
DT_SRAM_{BASE_ADDRESS,SIZE} and as CONFIG_SRAM_{BASE_ADDRESS,SIZE} (via
the Kconfig preprocessor).
Use the CONFIG_SRAM_* versions everywhere, and remove generation of the
DT_SRAM_* versions from gen_defines.py.
The Kconfig symbols currently depend on 'ARC || ARM || NIOS2 || X86'.
Not sure why, so I removed it.
It looks like no configuration files set CONFIG_SRAM_* at the moment, so
another option might be to use the DT_* symbols everywhere instead. Some
Kconfig.defconfig.series files add defaults to them though.
Also improve the help texts for CONFIG_SRAM_* to say that they normally
come from devicetree rather than configuration files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit removes the ignore tags for the tests that work after the
changes in the PR #20267.
In the future, this ignored testing tag list will be further reduced
as critical bugs for the qemu_cortex_r5 platform are addressed
(see #20217).
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The Xilinx ZynqMP SoC embeds both Cortex-R "RPU" and Cortex-A "APU"
cores.
Since the current Zephyr architecture cannot support AMP of Cortex-R
and Cortex-A within the same project, the RPU and APU should be
considered separate platforms and handled accordingly.
This commit re-purposes the SOC_XILINX_ZYNQMP symbol as a helper symbol
indicating that Xilinx ZynqMP SoC is used, and adds a new symbol,
SOC_XILINX_ZYNQMP_RPU, for specifying the actual build target platform.
When Cortex-A support is added in the future, SOC_XILINX_ZYNQMP_APU
symbol should be added and used to conditionally handle APU-specific
code.
For more details, refer to the issue #20217.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
ZynqMP SoC embeds two separate processor types: Cortex-R for RPU and
Cortex-A for APU.
Since the current Zephyr architecture cannot support AMP of Cortex-R
and Cortex-A within one project, the RPU and APU should be considered
separate platforms.
This commit relocates the device tree nodes that are not common between
RPU and APU to a separate dtsi file (zynqmp_rpu.dtsi).
When Cortex-A53 APU support is added in the future, an additional dtsi
file (zynqmp_apu.dtsi) for specifying the APU device tree should be
added.
For more details, refer to the issue #20217.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Based on this commit
| commit dd6186f299
| Author: Bobby Noelte <b0661n0e17e@gmail.com>
| Date: Sat Sep 30 18:24:46 2017 +0200
|
| boards: nucleo_f030r8: reduce kernel memory usage
|
| nucleo_f030r8 fails in CI because applications need
| more RAM.
|
| Reduce kernel memory used by stacks and ISR vector table.
|
| Fixes#3923
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
This enables LiteX PRBS random number generator driver
for litex_vexriscv board.
Signed-off-by: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Enable the NXP FTM PWM outputs in the board pinmux files based on the
DT_INST_* defines instead of CONFIG_PWM_* to match the pwm_mcux_ftm
driver.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the NXP FTM instances in the KE1xF SoC to PWM to match the
other SoCs/boards using the FlexTimer as PWM generator.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
At the moment we have different images for
for Nucleo F030R8 and Nucleo F070RB boards,
the images have the same pixel size but different
file formats, e.g:
NAMES="f030r8 f070rb"
for i in $NAMES; do
file boards/arm/nucleo_$i/doc/img/nucleo_$i.jpg;
done
boards/arm/nucleo_f030r8/doc/img/nucleo_f030r8.jpg: JPEG image
data, Exif standard: [TIFF image data, little-endian,
direntries=0], baseline, precision 8, 500x367, frames 3
boards/arm/nucleo_f070rb/doc/img/nucleo_f070rb.jpg: JPEG image
data, JFIF standard 1.01, aspect ratio, density 1x1,
segment length 16, progressive, precision 8, 500x367, frames 3
The nucleo_f030r8.jpg file is larger:
for i in $NAMES; do
ls -1 -sh boards/arm/nucleo_$i/doc/img/nucleo_$i.jpg;
done
128K boards/arm/nucleo_f030r8/doc/img/nucleo_f030r8.jpg
40K boards/arm/nucleo_f070rb/doc/img/nucleo_f070rb.jpg
Applying simultaneous black/white threshold to the images
and comparing them with imagemagick tools shows that
the images have no significant difference.
for i in $NAMES; do
convert boards/arm/nucleo_$i/doc/img/nucleo_$i.jpg \
-threshold 80% /tmp/$i.png;
done
compare $(for i in $NAMES; do echo -n "/tmp/$i.png "; done) \
-compose src /tmp/diff.png
See also 'boards: arm: unify Nucleo-64 boards connectors image'
(https://github.com/zephyrproject-rtos/zephyr/pull/15926).
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
This patchset enables USART3 on the 96Boards STM32 Mezzanine.
It is broken out to J10 Grove Connector.
Changes:
- Enabled USART3 in board dts.
- Updated board index.rst with uart pinouts.
- soc dtsi: enabled usart3.
Test: Tested USART3 as console at 115200 baud
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Move adafruit_2_8_tft_touch_v2 to Kconfig.defconfig format.
As part of this change Kconfig flags SPI and DISPLAY are removed
from the shield configuration as they are part of application
configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move dfrobot_can_bus_v2_0 to Kcondig.shield foramt and as part of
this change introduce nrf52_pca10040 board specific configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move link_board_can to conditional Kconfig.
As part of this change, some board specific symbols are moved
to reel_board specific file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move sparkfun_sara_r4 to conditional Kconfig.
As part of this change, remove disco_l475_iot1 specific configuration
as it is already part of board default configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Factorize definitions for ssd1306_128x32 and sd1306_128x64 shields
and move to conditional Kconfig.
As part of this change, direct drivers Kconfig symbols enabling
(I2C, SSD1306) are removed as they are application responsibility.
Also disabling SSD16XX is removed as SSD16XX should not be enabled
by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move wavehare epaper shields to conditional Kconfig.
As part of this change, direct drivers Kconfig symbols enabling
(SPI, SSD16XX) are removed as they are application
responsibility. GPIO is removed as well as it should be 'y' by
default on all boards according to Default board configuration
guidelines.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Put shield configuration Kconfig flags in new Kconfig.defconfig.
This way shield BLE subsystem can now be selected by application
using NETWORKING symbol, similarly to what is done when modem is
directly present on board.
Additionally, move board Kconfig files to a similar scheme where
shields related Kconfig flags are made available under shield,
board and NETWORKING symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Put shield configuration Kconfig flags in new Kconfig.defconfig.
This way shield BLE susbystem can now be selected by application
using BT symbol, similarly to what is done when BlueNRG ship is
directly present on board.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To make use of shields Kconfig.defconfig, parse these files
and newly created Kconfig.shield files which will define the
SHIELD_XXX Kconfig symbols that will be used for conditional
configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add Add STM32_OSPEEDR_VERY_HIGH_SPEED flag for SPI1_SCK to function
properly. This is needed for the proper communication with the LoRa
modem. Without this flag, the received data is mangled when burst
read is performed.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
The CONFIG_UP_SQUARED_{ATOM,CELERON,PENTIUM} symbols are unused after
commit c5e582038c ("boards/x86/up_squared: default to new local APIC
timer").
Since these symbols are the only thing in boards/x86/up_squared/Kconfig,
which is osource'd in in board/Kconfig, just remove the entire file.
Found with a script.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This adds support for the EC (embedded controller) on a Google
reference board with codename "kukui". This board uses the STM32F098RC
chip. We built an application for the board and verified UART
functionality on the board.
Signed-off-by: Jack Rosenthal <jrosenth@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Setup manual was modified, added detailed description how to launch
and program board, added more photos for better understanding
of the setup process.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Edited the index.rst file to say spi functionality is included. Also
edited the .yaml file in the boards directory to support spi for sanity
tests.
Signed-off-by: Jose Manuel Pacheco Luna <manuel.pacheco@nxp.com>
Added in enablement for the SPI-0 instance pins, as found in the
board schematic files. These connect to the arduino headers on the
front of the board.
Signed-off-by: Jose Manuel Pacheco Luna <manuel.pacheco@nxp.com>
Add the green LED on the back of the reel_board to the device tree and
add PWM support for the front RGB LED.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add at86rf233 dts binding to enable IEEE 802.15.4 driver. The driver is
managed by sercom-4 at chip level.
see: SAM-R21_G.pdf section: 5.2 Internal Multiplexed Signals
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
MX25R64 supports maximum 33 MHz clock for READ operations in
high-performance mode. The previous 80 MHz speed should have been
8 MHz and was for DSPI/QSPI operations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit removes any ignored testing tags for working tests.
In the future, this ignored testing tag list will be further reduced
as critical bugs for the qemu_cortex_r5 platform are addressed
(see #20217).
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds a temporary hack to support CI testing of the
qemu_cortex_r5 platform.
The Xilinx QEMU, required to run the tests for this platform, is
currently not available in the default SDK for CI (version 0.10.3) and
attempting to run any tests with the AArch64 QEMU included in this SDK
will cause failures (see #20217).
Since the latest SDK (version 0.11.0-alpha-8) has been added to the CI
image to allow initial testing, this hack automatically detects this
and uses the Xilinx QEMU for testing the qemu_cortex_r5 platform.
When the Zephyr SDK 0.11.0 is available as the default SDK for CI in
the future, this commit should be reverted.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit modifies the 'qemu_cortex_r5' board qemu emulation to use
the arm-generic-fdt machine with the Xilinx-provided zcu102 device tree
instead of the hard-coded xlnx-zcu102 machine, which is very primitive
and cannot properly emulate the Cortex-R5 RPU of ZynqMP.
The QEMU zcu102 FDT (fdt-single_arch-zcu102-arm.dtb) in this commit was
generated from the v2019.2 release of the Xilinx/qemu-devicetrees.
Zephyr SDK version 0.11 Alpha 4 or above is required to use this, as
arm-generic-fdt is supported only by the Xilinx QEMU fork which was
added to the Zephyr SDK in the version 0.11 Alpha 4.
For more details, refer to the issue #20217.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Add support for the ST STM32G0316-DISCO development board. This board
features an ST STM32G031J6 MCU on a breakable SO8 to DIL8 module, a user
LED and a button.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
SOC_FAMILY_NRF has no prompt. Assignments in configuration files have no
effect on symbols without prompts. A prompt means the symbol is
user-configurable.
SOC_FAMILY_NRF is instead enabled indirectly through being selected by
other symbols.
Detected through some work-in-progress improved error checking.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This patch enables SPI4 on the 96Boards STM32 Sensors Mezzanine.
SPI4 has been broken out to a Grove Connector on the board.
Changes:
- Updated board dts to enable spi4
- Updated board Kconfig
- Updated board documentation
- Update board pinmux
- Updated stm32f4 pinmux header file
- Updated stm32f401 dtsi
- Updated stm32f4 defconfig to enable PORTE GPIO
- Added board to spi_loopback test
Test: spi_loopback test passed
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Low frequency and high frequency clocks had separate devices
while they are actually handled by single peripheral with single
interrupt. The split was done probably because opaque subsys
argument in the API was used for other purposes and there was
no way to pass the information which clock should be controlled.
Implementation changes some time ago and subsys parameter was
no longer used. It now can be used to indicate which clock should
be controlled.
Change become necessary when nrf5340 is taken into account where
there are more clocks and current approach would lead to create
multiple devices - mess.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit targets solving issue #17731 over the LL_SW_SPLIT
arch of the BLE stack in Zephyr. This functionality is exposed
to the user as HCI Zephyr Command extensions
- BT_HCI_OP_VS_WRITE_TX_POWER_LEVEL
- BT_HCI_OP_VS_READ_TX_POWER_LEVEL
which enable Tx power read/write operations within BLE radio events
on a per role/connection basis.
The functionality is enabled upon the Kconfig advanced configuration
triggered by
- BT_CTLR_TX_PWR_DYNAMIC_CONTROL
depending on the enablement of Zephyr HCI vendor-specific command
extensions.
Necessary low-level radio HAL functionality and power definitions
are also supplied to address the high-level functionality of
controlling the Tx power.
Signed-off-by: Andrei Stoica <stoica.razvan.andrei@gmail.com>
Renames the lpc usart shim driver to more accurately reflect the
flexcomm hardware IP and to prepare for instantiating it on an SoC
outside the LPC family.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Configure as GPIOs pins that by default are not GPIOs
Enable pinmux for port F
Enable ADC, PWM drivers by default, but keep SPI disabled.
Swap I2C instances since I2C0 is multiplexed with UART2
Select VTR3 as 1.8V
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
EEPROM drivers that support STM32L1 have been tested
on 96b_wistrio boards.
EEPROM support is added to the board documentation.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fetch HW models from a new west module.
And, remove all pre-west glue which was used to:
* Fetch them in CI
* Validate their vesion
* Modify the include path and link to them
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Adds a device tree nexus node to define which gpio pins are mapped from
the soc to the arduino header.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a device tree nexus node to define which gpio pins are mapped from
the soc to the arduino header.
The frdm_kw41z board excludes the arduino A0 pin because it cannot be
muxed as a gpio on the soc.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the high-speed spi instance 8 on the lpcxpresso55s69 board.
Configures pinmuxes and clocks, and updates board documentation
accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
64BIT has no prompt. Assignments in configuration files have no effect
on symbols without prompts. A prompt means the symbol is
user-configurable.
64BIT is instead enabled indirectly through being selected by
BOARD_QEMU_RISCV64, which is enabled in the same configuration file.
Detected through some work-in-progress improved error checking.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
CPU_MINUTEIA has no prompt. Assignments in configuration files have no
effect on symbols without prompts. A prompt means the symbol is
user-configurable.
CPU_MINUTEIA is instead enabled indirectly through being selected by
other symbols.
Detected through some work-in-progress improved error checking.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
USE_CODE_PARTITION is a bit vague as a symbol name ("use code partition
how?"). Rename it to USE_DT_CODE_PARTITION to make it clearer that it's
about devicetree.
This would break any third-party configuration files that set it, but
it'll generate an error since kconfig.py promotes warnings to errors, so
it's probably not a big deal.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
In board pinmux.c ifdef of the form DT_GPIO_KEYS_SWx_GPIO_CONTROLLER
should be DT_GPIO_KEYS_SWx_GPIOS_CONTROLLER.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The original v1.3 had MMA8653+MAG3110, but v1.5 has verified LSM303AGR
and theoretical FXOS8700. Add the v1.5 variant 1 nodes in disabled
form; they can be enabled through overlays.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Created MEC1501 deep and light sleep example for MCHP MEC1501.
Modifications were made to SoC, board, timer, and hello world
sample program. Power management split into SoC power
implementing the interface and device power for device specific
logic.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Extended flash simulator for posix architecture to read/write data
from a binary file on the host file system.
Further enable the flash simulator by default on native_posix(_64)
boards and updated the documentation accordingly.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
olimexino_stm32 board doesn't have a
debugger. Now that stm32flash
runner is available, let's use it.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
SOC_FAMILY_ARM has no prompt. Assignments in configuration files have no
effect on symbols without prompts. A prompt means the symbol is
user-configurable.
SOC_FAMILY_ARM is instead enabled indirectly through being selected by
other symbols.
Detected through some work-in-progress improved error checking.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Commit ceffca2c42 added DTS support for board LEDs and buttons. Remove
redundant LED0_GPIO_PORT, SW0_GPIO_NAME, etc. defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add dts configs for bt-c2h-uart and bt-mon-uart. These are used by
the hci_uart sample and BT_DEBUG_MONITOR.
Signed-off-by: Rubin Gerritsen <Rubin.Gerritsen@nordicsemi.no>
In order to avoid a warning from Sphinx complaining that the
supported_features.rst file is not included in any ToC, rename it to
.txt so that Sphinx understands that this is only a snippet to be
included in other files.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The HiFive1 boards power up using a 32 KiHz low frequency kernel, so
have a cycle rate of 32768 Hz. The board definitions have not been
revisited since the Zephyr default for ticks-per-second increased from
100 to 10000. The timer system on the board does not operate
correctly at 4 cycles per tick, but does at 328 cycles per tick.
To support functional timers while keeping system milliseconds in sync
with clock time set ticks-per-second to 128.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
For consistency with all other boards, make the `buttons` node a child
of the root node, not the `leds` one.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
On LSM6DSO sensor the INT1 pin is used for both generating the drdy
interrupt and for switching to I3C hotjoin mode just after reset if
it is at logical '1' level. If you reset the x_nucleo_shield3 board
the LSM6DSO enter in hot join, as INT1 '1' level is preserved by
the level shifter.
This commit switch to INT2 to generate DRDY interrupt, so that INT1
always remain to logical '0' level.
Fixes: #20933
Signed-off-by: Armando Visconti <armando.visconti@st.com>
mps2_an521 is the default board for ARMv8-M architecture with
support for Security Extension, and CI should test building and
running samples and tests on this board by default. As the focus
is on kernel, userspace, and arm test suites, certain tags are
set to be ignored when testing on this platform.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In Zephyr we have the rule of "do not use stdint defined types",
but unfortunately that leaves us with no properly defined
format specifiers for printing values out.
So cast to stdint types in this expression to actually be able to
do so.
Fixes Coverity CID: 205798
Fixes Coverity CID: 205825
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
When building with support for BLE stack on the nRF5340 APP CPU
(Application MCU), use RPMsg HCI driver by default.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
When building with support for BLE stack, enable the BT_ECC
for the nRF5340 NET CPU (Network MCU).
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
When building with support for BLE stack, enable the Vendor Specific
commands for the nRF5340 APP CPU (Application MCU).
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Provide the mapping from FE310-G002 GPIO pins to the Arduino Uno
headers. Note where pins have pre-assigned functions that may
interfere with use as GPIOs with the default pinmux assignments.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Adds missing items to the list of supported features for all nxp imx rt
boards. These features were already supported, just missing from the
list.
This change increases the number of samples and tests that sanitycheck
selects for these boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Sorts the list of supported features in alphabetical order for all nxp
boards. No features are added or removed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Link to Nordic Semiconductor Infocenter, instead of DocLib
in the documentation for nRF-based Development Kits.
Change Nordic Semi to Nordic Semiconductor in the
DK figure captions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Some people are behind firewalls that prevent them
from doing ssh connections.
Change the default BabbleSim fetching instructions to
be over https which should work for everybody.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
A partition start offsets should be expressed relative to the flash
device base address. For cpunet flash partitions start offsets
were improperly expressed as absolute flash address.
This patch fixes partitions start addresses for nRF5340 cpunet.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Since the nRF5340 DK contains the required DC/DC circuitry,
enable it by default while keeping it configurable. This
reduces power consumption in application core , network
core and high voltage use.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Explicitly configures the rgb led pinmuxes as gpios. Currently the gpio
driver quietly changes the pinmux to gpio mode when configuring a gpio
pin, but this behavior is about to change.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Some board description files failed to note where gpio was supported,
causing tests to be inappropriately filtered. Add the feature where
the gpio_basic_api test would use it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Name convention for nordic USB driver changed
Kconfig files for custom boards have to be udapted accordingly.
Changes affect only name convention change.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This commit adds support for nRF52833 development board.
Changes afffects:
- Introduce files related to board description.
- Add blank documentation file (for future update).
- configuration files for build process.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This commit enables CAN support for the Olimexino STM32 board.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
commit 0df4a53107 changed the behavior of
how openocd commands are passed to openocd. We used to add -c to each
command, now the commands are being added without -c causing an error.
This adds "-c" to all commands instead of just passing a list.
Also fixes#20449.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Provide information required to allow the driver to put the flash chip
into a deep power down mode. This can reduce standby current by as
much as 90%.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The SPI NOR driver requires that the size (in bits) be provided in the
devicetree node. Update the binding to make the property required,
and update all nodes based on the memory chip identified.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The races are believed to be resolved with the patch to
irq_offload(). Allow the MMU to be turned on and enable
it for qemu_x86_64.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We add the functionality that allows the nRF5340 Application
MCU to boot the Network MCU by releasing the RESET line. The
Application MCU may optionally allocate and corfigure resources
that the Network MCU is going to use (currently GPIO and secure
attribution) if running in secure mode. Non-Secure Application
MCU firmware can only issue Network MCU resets.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
When building with support for BLE stack, enable
the BLE Controller module for the nRF5340 DK NRF5340
CPUNET (Network MCU).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Enables the arm v7m mpu on the efr32mg soc and the board
efr32mg_sltb004a.
Tested on hardware with samples/mpu/mpu_test and
tests/kernel/mem_protect
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Specific SW defined BLE LL parameters need to be set
if the user enables it on this platform. As such, conditionally
enable them directly into the defconfig.
INTMUX CH2 and CH3 are not available to be used if BT support
is enabled on Vega, because they are used internally by the
BLE SW LL
Signed-off-by: David Leach <david.leach@nxp.com>
Since the experimental BLE software link layer is enabled on
the VEGABoard, add some information about it, as well as the
limitations.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Having a pin toggle when the code reaches a certain point
is really useful for debugging; the infrastructure is already
in place for Nordic boards, so just build upon and enable the
mechanism on the Vega board as well.
Signed-off-by: David Leach <david.leach@nxp.com>
Update the models revision used for building so that nrf52_bsim
can be used with nrfx 2.0.0.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Calls to nrfx HAL functions in various nRF platform related source
files are complemented with pointers to relevant peripherals.
Additionally, TIMER HAL functions that got renamed in nrfx 2.0.0 are
updated in the qemu_cortex_m0 board supporting code.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
When calling posix_print_error_and_exit()
a return != 0 was not provided to the shell
This was due to thee way the tracing functions call back
into the main app exit function, assuming that callback
will return.
But in the SOC_INF boards, that function does
not return, and the tracing functions never have the
chance to exit(!=0)
Fix it by calling posix_exit() in the wrap function instead.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Promote the private z_arch_* namespace, which specifies
the interface between the core kernel and the
architecture code, to a new top-level namespace named
arch_*.
This allows our documentation generation to create
online documentation for this set of interfaces,
and this set of interfaces is worth treating in a
more formal way anyway.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The board area was renamed from riscv32 to riscv back in July to
accommodate riscv64 support. Fix the remaining references in
documentation.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Some boards require specific sequences of commands to run which aren't
generally useful for other boards. Add a catch-all runner to handle
these cases.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This commit refactors kernel and arch headers to establish a boundary
between private and public interface headers.
The refactoring strategy used in this commit is detailed in the issue
This commit introduces the following major changes:
1. Establish a clear boundary between private and public headers by
removing "kernel/include" and "arch/*/include" from the global
include paths. Ideally, only kernel/ and arch/*/ source files should
reference the headers in these directories. If these headers must be
used by a component, these include paths shall be manually added to
the CMakeLists.txt file of the component. This is intended to
discourage applications from including private kernel and arch
headers either knowingly and unknowingly.
- kernel/include/ (PRIVATE)
This directory contains the private headers that provide private
kernel definitions which should not be visible outside the kernel
and arch source code. All public kernel definitions must be added
to an appropriate header located under include/.
- arch/*/include/ (PRIVATE)
This directory contains the private headers that provide private
architecture-specific definitions which should not be visible
outside the arch and kernel source code. All public architecture-
specific definitions must be added to an appropriate header located
under include/arch/*/.
- include/ AND include/sys/ (PUBLIC)
This directory contains the public headers that provide public
kernel definitions which can be referenced by both kernel and
application code.
- include/arch/*/ (PUBLIC)
This directory contains the public headers that provide public
architecture-specific definitions which can be referenced by both
kernel and application code.
2. Split arch_interface.h into "kernel-to-arch interface" and "public
arch interface" divisions.
- kernel/include/kernel_arch_interface.h
* provides private "kernel-to-arch interface" definition.
* includes arch/*/include/kernel_arch_func.h to ensure that the
interface function implementations are always available.
* includes sys/arch_interface.h so that public arch interface
definitions are automatically included when including this file.
- arch/*/include/kernel_arch_func.h
* provides architecture-specific "kernel-to-arch interface"
implementation.
* only the functions that will be used in kernel and arch source
files are defined here.
- include/sys/arch_interface.h
* provides "public arch interface" definition.
* includes include/arch/arch_inlines.h to ensure that the
architecture-specific public inline interface function
implementations are always available.
- include/arch/arch_inlines.h
* includes architecture-specific arch_inlines.h in
include/arch/*/arch_inline.h.
- include/arch/*/arch_inline.h
* provides architecture-specific "public arch interface" inline
function implementation.
* supersedes include/sys/arch_inline.h.
3. Refactor kernel and the existing architecture implementations.
- Remove circular dependency of kernel and arch headers. The
following general rules should be observed:
* Never include any private headers from public headers
* Never include kernel_internal.h in kernel_arch_data.h
* Always include kernel_arch_data.h from kernel_arch_func.h
* Never include kernel.h from kernel_struct.h either directly or
indirectly. Only add the kernel structures that must be referenced
from public arch headers in this file.
- Relocate syscall_handler.h to include/ so it can be used in the
public code. This is necessary because many user-mode public codes
reference the functions defined in this header.
- Relocate kernel_arch_thread.h to include/arch/*/thread.h. This is
necessary to provide architecture-specific thread definition for
'struct k_thread' in kernel.h.
- Remove any private header dependencies from public headers using
the following methods:
* If dependency is not required, simply omit
* If dependency is required,
- Relocate a portion of the required dependencies from the
private header to an appropriate public header OR
- Relocate the required private header to make it public.
This commit supersedes #20047, addresses #19666, and fixes#3056.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This support is Zephyr RTOS aware, so you can debug threads as well.
Add a CMake fragment which adds openocd support for nrf5 boards which
can also be flashed via JLink. This ought to work for nRF51 and nRF52
based boards at time of writing with openocd 0.10.0 or later (zephyr
SDK 0.10.3 also worked when I tried for nrf52840_pca10056).
Use it from the nRF DKs from Nordic which have interface MCUs with
Segger compatible firmware. I'm also including Thingy:52, even though
it doesn't, to make it easier when connecting to it via a standalone
JLink dongle. The board has a nice connector for that.
I'm leaving non-Nordic boards alone for now because I don't know them.
It's just one line of CMake to add it for other boards, which should
be easy for their maintainers to do.
Suggested-by: Radosław Koppel <radoslaw.koppel@nordicsemi.no>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Introduce a standard watchdog alias 'watchdog0' that can be utilized
by sample/test code in the future. This helps remove the need for
CONFIG_WDT_0_NAME in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_0_ARM_CMSDK_WATCHDOG_LABEL instead of
CONFIG_WDT_0_NAME. This requires we introduce a "label" property in all
the related dts files. Also introduce a standard watchdog alias
('watchdog0') that can be utilized by sample/test code in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
dts pinctrl definitions were pushed in tree without the code
available to deal with it. They have been kept waiting for the
code, but this is taking much more time than initially thought.
So in current zephyr tree, for all STM32 boards, we have pinmux.c
file which is used to configure pins and these files that are
basically no-op. This situation is creating a lot of confusion
especially to new comers, and create useless maintenance effort.
Remove these files for now.
When zephyr will ready to use them, this commit could be reverted.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update shield description and sample to allow testing of LIS3MDL
sensor IRQ pin.
Update sample yaml file to state dependency on arduino_gpio.
Additionally, fix redundant line in sample yaml
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
DMA is now selected by Kconfig symbols in I2S, and DMA_STM32
is selected by DMA in
soc/arm/st_stm32/common/Kconfig.defconfig.series. So remove the
DMA selecting operation here.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Previous defconfig for dma is DMA_STM32F4X in this board, while the new
generic driver uses DMA_STM32 to enable DMA support, and also dma driver
of stm32 now needs HEAP_MEM_POOL_SIZE to be big enough to hold dma
stream instances.
Additional .conf files are added for also adding HEAP_MEM_POOL_SIZE
configuration to two test cases.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Update ccs811 dts binding to include GPIO pins for wakeup, reset, and
interrupt and change driver code to get the GPIO pin and controller
info from DT instead of Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SensorTile.box SPI3 bus hosts the LIS2MDL device connected
in 4-wires mode (full duplex MISO and MOSI lines) by default.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Update vl53l0x dts binding to include GPIO XSHUT pin and change
driver code to get the GPIO pin and controller info from DT instead of
Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Experimentation with RSSI checks of BLE scans confirms that the
antenna switch setting is incorrect on the argon, boron, and xenon
platforms: when PCB is selected, performance is best with a uFL
antenna, and vice-versa. Checks against the Particle OpenThread
firmware confirm that the correct practice is to invert the settings.
Though the SKY 13351 SPDT switch datasheet suggests otherwise it seems
the VCTLx signals are active low.
Switch the sense of all antennal selection output operations.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add details for features exposed via headers.
Add power management recommended setup.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Add support for the NXP TWR-KV58F220M development board. This board
features an NXP MKV58F24 MCU, four user LEDs and four buttons,
potentiometer, two TWRPI headers, and a motor control header.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
1) Add cryptographically secure random functions to provide
FIPS 140-2 compliant random functions.
2) Add name to random function choice selectors to ease
selection in SOC .defconfig files
3) Add bulk fill random functions.
Signed-off-by: David Leach <david.leach@nxp.com>
Putting 'if's directly on the defaults is simpler here.
I'm guessing BOARD should always be "musca_{a,b1}_nonsecure" if it isn't
"musca_{a,b1}", so I removed the condition on the
"musca_{a,b1}_nonsecure" default (turning it into an "else").
Avoiding a top-level 'if'/'depends on' also avoids adding direct
dependencies to the BOARD symbol, which looks a bit neater in the
generated docs (though direct dependencies only matter for symbols that
might be selected/implied).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The 1ms wait time has been shown to not be enough. Increasing to 10ms.
This change has been shown to be necessary after
CONFIG_SYS_CLOCK_TICKS_PER_SEC was changed from 128 to 32768
in https://github.com/zephyrproject-rtos/zephyr/pull/16782
Signed-off-by: Sigurd Olav Nevstad <sigurdolav.nevstad@nordicsemi.no>
This MCU has sectors of size 4096, but some partitions were aligned to
0x800 addresses. MCUBoot detects this incosistency and halts. This patch
fixes the partitions to use properly aligned addresses (multiples of
0x1000).
Signed-off-by: Fabio Utzig <utzig@apache.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Building `smp_svr` for this board results in a build error due to
undefined symbols `DT_NXP_KINETIS_UART_4006D000_*` which are related to
uart3 DTS symbols not being generated. This marks uart3's status as OK.
Signed-off-by: Fabio Utzig <utzig@apache.org>
Enable the MX25R32 SPI NOR Flash on the VEGAboard and provide board
config file for the spi_flash sample.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
This utilizes the newly introduced dediprog west flash runner to flash
the image onto the onboard SPI chip.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Unlike most other GPIO controllers which support 32 pins this device
only supports 16. (There is an SX1508B that has 8 pins, but the
driver doesn't support it.)
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Comparing the output of "west boards" with mentions of boards in build
instructions (:board: boardname) found a couple of incorrect board
references.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Convert the NXP Kinetis ADC12 driver from relying on CONFIG_ADC_n
Kconfig defines to using DT_INST defines for instance configuration.
This resolves the issue of having e.g. ADC12 instances 2 and 3
enabled, but not instance 0.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for 1.8v Low speed connector available on the Wistrio
board inorder to access peripherals in a board independent way.
Following peripherals are supported:
1. 12-GPIOs
2. SPI0
3. UART0
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Add support for 3.3v Low speed connector available on the Carbon
board inorder to access peripherals in a board independent way.
Following peripherals are supported:
1. 8-GPIOs
2. I2C0
3. SPI0
4. UART0
5. UART1
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Add support for 3.3v Low speed connector available on the Wistrio
board inorder to access peripherals in a board independent way.
Following peripherals are supported:
1. 7-GPIOs
2. I2C0
3. UART0
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Unused since commit 7809970c8a ("drivers: counter: cmsdk: Convert to new
DT_<COMPAT>_<INSTANCE> defines"). Kconfig.defconfig leftover.
Found with a script.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Added in commit f9efca4b4f ("boards: riscv32: add LiteX VexRiscV
board"), then never used.
Found with a script.
Also change UART_LITEUART from a 'menuconfig' symbol to a 'config'
symbol, as it's no longer followed by symbols that depend on it
(UART_LITEUART_PORT_0 should have been a plain 'config' too).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
There are two set of code supporting x86_64: x86_64 using x32 ABI,
and x86 long mode, and this consolidates both into one x86_64
architecture and SoC supporting truly 64-bit mode.
() Removes the x86_64:x32 architecture and SoC, and replaces
them with the existing x86 long mode arch and SoC.
() Replace qemu_x86_64 with qemu_x86_long as qemu_x86_64.
() Updates samples and tests to remove reference to
qemu_x86_long.
() Renames CONFIG_X86_LONGMODE to CONFIG_X86_64.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
posix_soc_if.h is meant to be a private header between
the POSIX ARCH, SOC, and maybe boards,
it should not contain definitions meant to be used directly
by the kernel or app.
Some definitions were placed here due to a dependency moebius
loop.
Unravel that by removing all header dependencies in posix_soc_if.h,
move those definitions out to a more logical place,
and while we are here reduce the amount of users of
irq_offload.h in POSIX arch related code
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The Thingy:52 has a LIS2DH12 low-power accelerometer on the external
I2C bus. Add the necessary description to devicetree.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Unused since commit 7e96ca5d80 ("i2c: Remove non DTS Kconfig params").
intel_s1000_crb probably isn't getting tested in CI, because Kconfiglib
generated a warning for the symbol no longer being given a type, which
would be turned into an error.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Same deal as in commit 7fdb525754 ("kconfig: Use 'default' instead of
'def_bool' in Kconfig.defconfig files"), but I hacked Kconfiglib to also
find cases where the type is given separately as e.g.
config FOO
int
default 3
Motivation (from a note in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html):
For a symbol defined in multiple locations (e.g., in a
Kconfig.defconfig file in Zephyr), it is best to only give the
symbol type for the "base" definition of the symbol, and to use
'default' (instead of 'def_<type>' value) for the remaining
definitions. That way, if the base definition of the symbol is
removed, the symbol ends up without a type, which generates a
warning that points to the other definitions. That makes the extra
definitions easier to discover and remove.
It's also nice if 'def_bool' and the like turn into a semi-reliable flag
that the symbol is only defined in Kconfig.defconfig files. That might
be a sign that things could be cleaned up.
Will do a separate pass later to remove some symbols only defined in
Kconfig.defconfig files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Replace:
dt_chosen_reg_addr
dt_chosen_reg_size
dt_node_reg_addr
dt_node_reg_size
with:
dt_chosen_reg_addr_int
dt_chosen_reg_size_int
dt_chosen_reg_addr_hex
dt_chosen_reg_size_hex
dt_node_reg_addr_int
dt_node_reg_size_int
dt_node_reg_addr_hex
dt_node_reg_size_hex
So that we get the proper formatted string for the type of symbol.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Should be within the 'if BOARD_NATIVE_POSIX`, or USB_NATIVE_POSIX will
get enabled whenever USB is (unless a user value overrides it).
Probably didn't cause any problems, since
boards/posix/native_posix/Kconfig.defconfig is only included for this
board.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Configure the pin connected to edge LED as PWM output.
On the new board version 1507.3 this pin also controls a buzzer.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Now that everything is DT based for I2C drivers we can rename the
CONFIG_I2C_[0..5]_NAME define to DT_I2C_[0..5]_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all I2C drivers utilize DTS we can select HAS_DTS_I2C in a
common place and don't need to do it per driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update board dts files to add User LED and Button support. Also update
the board yaml file to say the boards support gpio.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add binding for arm,mps2-fpgaio-gpio and update device tree and change
FPGA GPIO init code to utilize device tree defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configures the default instance of the sdhc driver for the
mimxrt1050_evk board so applications don't have to configure it
explicitly. Similarly, enables the gpio instance required by the sdhc
driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
We need to be able to specify GPIO flags in devicetree without that
preventing translation from the Arduino specifier to the host GPIO
specifier. Set up to ignore the low 6 bits of the flags field when
matching the child specifier, and to copy those bits to the parent
specifier.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Unused since commit 6fd6b7e50a ("xtensa: remove legacy arch
implementation").
Found with a script.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Duplicate definitions elsewhere have been removed.
A couple functions which are defined by the arch interface
to be non-inline, but were implemented inline by native_posix
and intel64, have been moved to non-inline.
Some missing conditional compilation for z_arch_irq_offload()
has been fixed, as this is an optional feature.
Some massaging of native_posix headers to get everything
in the right scope.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
With this commit we add the option to use jlink for
flashing and running samples & tests on Arduino Due
using jlink. Bossac remains the default option.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Unused since commit 0829ddfe9a ("kbuild: Removed KBuild").
This symbol is the only thing in boards/xtensa/xt-sim/Kconfig,
which gets included via
osource "$(BOARD_DIR)/Kconfig"
in boards/Kconfig, so just remove the entire file.
Found with a script.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The RAK811 module used on this board incorporates STM32L151CB-A SoC,
which has more RAM (32 KiB) compared to its companion STM32L151CB.
Hence, fix the doc, dts and Kconfig to include correct part number.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
We enable Memory Protection on stm32 nucleo_g071rb board,
since the respective SoC series implements the ARM MPU.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Remove the
# Omit prompt to signify a "hidden" option
comments that appear on some symbols. They seem to have been copy-pasted
at random, as there are lots of promptless symbols that don't have them
(that's confusing in itself, because it might give the idea that the
ones with comments are special in some way).
I suspect those comments wouldn't have helped me much if I didn't know
Kconfig either. There's a lot more Kconfig documentation now too, e.g.
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Keep some comments that give more information than the symbol having no
prompt.
Also do some minor drive-by cleanup.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Change default flash size and offset to use the new kconfig function
`dt_chosen_reg_addr` instead of deprecated `dt_hex_val`
Signed-off-by: Alex Tsamakos <alex@actinius.com>
A style was recently added that will allow long narrow lists to display
as three columns across the page (with a responsive design that
self-adjusts based on screen width). This looks much better than a long
list that runs down the page.
Adding this directive before a block (or nested under the directive)
will allow the content to be multi-column:
.. rst-class:: rst-columns
as explained in
https://docs.zephyrproject.org/latest/guides/documentation/index.html
in the Multi-column lists section.
This PR tweaks a few remaining documents that have such long narrow
lists.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add configuration file for the stm32mp157c_dk2.
Beacon, Central are working.
Peripheral is not compiling because of .elf exceeding FLASH region,
else should be working.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add shield x_nucleo_idb05a1.
Tested samples with the disco_l475_iot1 (SPI3 disabled to ensure
to test the shield on SPI1, and not the on-board BlueNRG-MS chip):
Beacon, Central and Peripheral have been tested and are working.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Erwan Gouriou <erwang.gouriou@linaro.org>
Enable RTOS, PS2, PWM and ADC for modular MEC15xx
Add extra step to build flashable image.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Move systick activation in soc/ as a Kconfig.defconfig file and
remove activation in boards _defconfig files.
This will allow to deactivate it in a more flexible way
with upcoming LPTIMER as tick source when power management
features are enabled.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
For some reason UART_2 and UART_3 was not marked "okay" in the device
tree, making use difficult.
I have tested both UARTs on a "blue pill" board (stm32_min_dev_blue)
with both polling and RX/TX interrupts and found them to work as
expected.
Signed-off-by: Tommy Vestermark <tovsurf@vestermark.dk>
The POSIX ARCH delegates some of the tasks which normally
are taken care of by the ARCH to the SOC or BOARD levels.
To avoid changes in the kernel-arch IF propagating into
the arch-soc and arch-board interfaces (which would break
off-tree posix boards) isolate them.
Also move arch inlined functions into the arch.h header,
and out from the headers which specify the posix arch-soc
and arch-board interfaces.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The specification for these arch APIs is to have them inline,
and the bodies were just oneliners calling another function
anyway.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Re-run with updated script to convert integer literal delay arguments to
k_sleep to use the standard timeout macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Set the bus speed to 125000 like the other boards.
Remove the SPI definition.
Move the definition of the oscillator frequency from Kconfig
to the device-tree.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Updated connection info and restructered a bit some paragraphs to stay
consistent with the structure of other boards.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
found some references to files (via :zephyr_file: and :zephyr-app:) that
were moved, so the links were broken
Fixes: #19660
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
DTSpec writes this as a single word, presumably to make it easier to
grep for / more precise. Follow along in the rest of the docs now that
our main DT docs page agrees with this usage.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Add duplicate per-CPU data structures (x86_cpuboot, tss, stacks, etc.)
for up to 4 total CPUs, add code in locore and z_arch_start_cpu().
The test board, qemu_x86_long, now defaults to 2 CPUs.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
And set qemu_x86_long board to build with CONFIG_SMP=y by default.
Apparently two benchmark tests - latency_measure and sys_kernel -
do not work with the SMP scheduler, so those tests are disabled.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Apply same scheme for all nucleo_64 pins boards:
-provide a separate arduino connector dtsi file
-provide complete gpio map
-update board.yaml vs arduino support (i2c, spi and gpio)
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add KConfig board support to match board jumper settings
Failing to update bank selection will affect GPIOs tied to VTR3
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
The `pwm-led0` alias is required for building fade_led and blink_led
samples. Add a suitable `pwmleds` definition and the mentioned alias
for all Nordic Semiconductor Development Kits that have a PWM node
with "okay" status.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The incomming new NRF clock driver requires extra nrf HAL
and drivers functions, which are only supported in the HW models
after version 1.8
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Fix a possible leak if `realloc` fails here; check the result of the
`realloc` call before updating the pointer, so it can be freed in the
failure case.
Signed-off-by: Noah Pendleton <noah.pendleton@gmail.com>
Now that we have a QEMU board for Cortex-M0, and set as default,
we do not need to have nrf51_pca10028 as default board.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
For the qemu_cortex_m0 we implement a custom system clock
driver based on the nRF51 TIMER peripheral. The system
clock is configured to run at 1 MHz frequency.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit configures the qemu_cortex_m0 board to
build with it's custom timer driver, instead of the
default nrf_rtc_timer driver for nRF51x SoCs. It,
additionally, configures a default system clock
frequency to 1MHz, as well as 10 Hz tick frequency.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds some documentation for the
newly introduced qemu_cortex_m0 platform.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit defines qemu_cortex_m0 board, adding
support for Cortex-M0 in QEMU. The added platform
is based on the (nRF51) bbc_microbit board.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This makes it clearer that this is an API that is expected
to be implemented at the architecture level.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Simple naming change, since MULTIBOOT is clear enough by itself and
"namespacing" it to X86 is unnecessary and/or inappropriate.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Implement a simple ACPI parser with enough functionality to
enumerate CPU cores and determine their local APIC IDs.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Mostly build tests now, will be extended to verify CTF output once we
have this feature in sanitycheck.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This adds a way to specify a custom SPI configuration file to be
used with the image generation tool. For example, this can be
used to reduce the SPI image size to allow faster flashing
(e.g. 512KB instead of 16MB).
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Configure interrupt gpio information (irq-gpios) into the
x-nucleo-iks01a3 shield overlay file.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit introduces separate "compatible" strings for DTS nodes
representing different types of Nordic SPI peripherals. Previously
"nordic,nrf-spi" was used for both SPI and SPIM. SPIS was already
handled separately.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/spi/
new binding for "nordic,nrf-spim" is added and common fields for all
3 types of Nordic SPI peripherals are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in spiX nodes are updated (when there is no
choice as only one type of SPI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/spi/
spi_nrfx_spim driver is updated with the new form of macros generated
from dts
* boards/
all spiX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of SPI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (SPI_x_NRF_SPI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit introduces separate "compatible" strings for dts nodes
representing different types of Nordic TWI peripherals. Previously
"nordic,nrf-i2c" was used for both TWI and TWIM, and TWIS was not
supported.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/i2c/
new bindings for "nordic,nrf-twim" and "nordic,nrf-twis" are added
and the one for "nordic,nrf-i2s" is renamed to "nordic,nrf-twi",
common fields for all these bindings are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in i2cX nodes are updated (when there is no
choice as only one type of TWI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/i2c/
both flavors of i2c_nrfx drivers are updated with the new names of
macros generated from dts
* boards/
all i2cX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of TWI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (I2C_x_NRF_TWI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable CMSDK GPIO driver on v2m_musca_b1 SoC/Board. Add LEDs that are
on the board and init the pinmux for those LEDs to work.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Utilize CONFIG_TRUSTED_EXECUTION_NONSECURE to decide if we do pinmux.
This Kconfig option is more useful since we only set the _SECURE
version isn't set if we are ignoring the security mode feature.
Move the LED pinmux setup into the not NONSECURE case.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds support for NXP's Freedom K22 board.
Co-authored-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Co-authored-by: Tom Burdick <thomas.burdick@gmail.com>
Signed-off-by: Tom Burdick <thomas.burdick@gmail.com>
Header files of nrfx HALs are not supposed to be included directly
but only with their names prepended with the hal/ directory (so that
an inclusion of an nrfx HAL header clearly differs from an inclusion
of an nrfx driver header).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The QEMU x86 .dts files were re-arranged before long mode was
merged. We don't need this reference to the flash region anymore.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>