Remove `clocks` property for fixed-clock binding.
A fixed-clock should not have an input clock, since by
definition it's an always on fixed-rate clock.
Signed-off-by: Moritz Fischer <moritzf@google.com>
This adds a driver for Texas Instruments Cost-Optimized, Ultra-Small,
12-Bit, System-Monitoring ADCs. Currently only TLA2021 is supported,
TLA2022 and TLA2024 may follow based on this driver.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Convert the XPT2046 driver to the input subsystem, change the api,
remove the callback and enable logic.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Usage of 64-bit address constants from devicetree without a
UINT64_C wrapping macro results in the following warning and the
cut-off of the address value:
"warning: integer constant is so large that it is unsigned"
This change extends devicetree API adding few wrappers over the
address constant getters which add ULL size suffix to an
address integer literal when the appearance of 64-bit address
values is possible
Signed-off-by: Alexander Razinkov <alexander.razinkov@syntacore.com>
Add a GPIO based quadrature decoder driver that reports relative axes
movements using the input subsystem.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Adds properties to configure OCTOSPI IO
Manager data lines. That allows to use
any `IOLowPort` and `IOHightPort`.
Note: OSPIM requires additional clock to be enabled.
Please refer to Reference Manual.
Extra clock can be enabled in devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Add Nuvoton numaker series UART support, including interrupt-driven,
also apply pinctrl and clock-control.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Add Nuvoton numaker series clock controller support, including:
1. Do system clock initialization in z_arm_platform_init().
2. Support peripheral clock control API equivalent to BSP
CLK_EnableModuleClock()/CLK_SetModuleClock().
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
Add support for communication with serial ports on native POSIX platform
via UART driver API. Serial port driver supports polling API,
configuration of the serial ports used via devicetree and command line
options, and runtime configuration with `uart_configure`.
Multiple instances of the driver are supported.
Example use and configuration is also demonstrated in the
`samples/drivers/uart/native_tty` sample.
Closes: #56586
Signed-off-by: Marko Sagadin <marko.sagadin42@gmail.com>
The IS31FL3216A is a fun light LED controller. The LED current of each
channel can be set in 256 steps by adjusting the PWM duty cycle through
an I2C interface.
Signed-off-by: Guy Morand <guy.morand@bytesatwork.ch>
Add a minimal driver for the ti lp5569 led controller. The driver supports
multiple instances. Commands on|off|set_brightness are supported.
Signed-off-by: Jonas Remmert <j.remmert@phytec.de>
Currently, only the presence of a GIC is reflected in the device tree,
and its version must be set separately in each SoC's Kconfig.
This patch adds separate bindings for each GIC version whose presence
in the device tree automatically enables the corresponding Kconfig symbol.
Signed-off-by: Piotr Wojnarowski <pwojnarowski@antmicro.com>
When the GIC driver was originally introduced, it was only used on
Cortex-R SoCs. However, this is not the case anymore. Update the
description to reflect that this driver is not specific to Cortex-R.
Signed-off-by: Piotr Wojnarowski <pwojnarowski@antmicro.com>
Add driver for TCN75A temperature sensor. The following features are
supported:
- TCN75A oneshot mode, which allows single shot conversions with lower
power consumtion
- Resolution selection, up to 12 bit resolution (9 bit default)
- Triggering based on temperatue thresholds. If the TCN75A exits a set
threshold range, the application can be notified via a callback.
Signed-off-by: Daniel DeGrasse <daniel@degrasse.com>
Add a new pinctrl driver for TI CC32XX SoC. The driver has not been
tested, just implemented following datasheet specs and checked that it
compiles. Consider this as a best-effort driver to remove custom pinmux
code in board files.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This PR adds a custom driver for the ADS1112 ADCs. Unlike ADS1113/4/5
family served by the ADS1x1x driver, the ADS1112 does not use an address
pointer to address config registers. Instead, there is only one writable
register and all i2c writes will set it. The registers resemble the
ADS1119 device, but config bitmap is different, include a distinct data
rate table, gain table, and input multiplexing table. There is also not a
status register to be monitored with the ADS1112, as it uses config bit 7
for the same purpose instead of a separate register.
The driver was tested on hardware using the ADC shell interface. Manual
probing validated the voltages for the MUX_SINGLE configs at datarate 15
in CM_SINGLE. Higher gains were not tested and CM_CONTINUOUS is not
supported in this initial implementation.
The new driver has also been added to the existing ADC test using adc_emul
for completeness.
Origin: original
License: Apache 2.0
Purpose: Adding support for ADS1112 ADCs
Signed-off-by: Jordan Montgomery <jordan.montgomery@getcruise.com>
Restructure the Bosch M_CAN driver backend to use per-instance Message RAM
configuration.
This removes the need for a common, artificial "can" devicetree node for
SoCs with multiple Bosch M_CAN-based CAN controllers and allows for
per-instance configuration of the number of e.g. standard (11-bit) and
extended (29-bit) filter elements.
As part of the restructure, software handling of CAN filter flags was moved
from per-flags bitfields to per-filter bitfields, solving an issue when
using more than 32 standard (11-bit) filter elements or more than 16
extended (29-bit) filter elements.
Fixes: #42030, #53417
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Switch the Bosch M_CAN devicetree binding to use a bosch,mram-cfg property
for specifying the memory layout of the Bosch M_CAN Message RAM. This is
identical to the Linux kernel devicetree binding for Bosch M_CAN IP core
based CAN controllers.
This introduces an offset cell which can be used for controllers with
shared Message RAM between Bosch M_CAN instances.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The BG95 pin configuration does not internally ever use the reset pin.
Because of this, there is no need to make reset pin mandatory.
Commit removes reset pin dependency [e.g. in case of BG95].
Signed-off-by: Andrei Hutanu <andrei.hutanu.i@gmail.com>
Add a property to the ADC channels which allows the configuration
of the current source pin.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Added Input/Output trigger mux address's as properties
that can be passed into the DMA driver. This is intended
to send INPUTMUX signals into the DMA.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Ports the Jinghua Display JHD1313 LCD (with RGB backlight) driver
to use the new auxdisplay driver interface. This driver is used on
the seeed grove LCD RGB display, and replaces it.
Signed-off-by: Jamie McCrae <spam@helper3000.net>
Removed few VIF properties which are being hardcoded
Updated the script to parse source VIF XML and add information to
the output
Added optional Kconfig option to configure custom source VIF XML path
Cleaned up the code
Signed-off-by: Madhurima Paruchuri <mparuchuri@google.com>
Added intel LPSS DMA interface using dw common to support
usage of internal DMA in LPSS UART, SPI and I2C for
transfer and receive operations.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Adds PHY driver. Works via MDIO API and
exposed ADIN2111 MDIO Clause 45
functions.
Link status detection is triggered by
ADIN2111 driver within offloaded IRQ
handler.
Supports:
- LED0, LED1 enable/disable
- Fatal HW error detection
- AN 2.4V tx mode enable/disable
The initialization order is important.
PHY 2 must be initialized after PHY1.
Therefore, it shall be defined after the 1st one
in the devicetree.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds MDIO driver. Works via exposed
ADIN2111 functions.
It is possible to access Clause 45 and 22 registers.
Due to MDIO API limitation Clause 45 access
is done using driver specific MDIO functions.
Provides API and functions for PHY driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds initial ADIN2111 2-Port 10BASE-T1L (SPE)
switch support. Works over SPI.
The driver creates 2 interfaces, 1 per port (PHY).
Configures multicast and broadcast filters.
The same unicast is applied to both ports.
Supports:
- Link state detection
- CRC enable/disable
- Ports config set
- Ports ETH stats
Provides functions for MDIO driver.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
The OpenTitan power manager is responsible for changing the OpenTitan's
operation to and from low power state. This patch adds a simple binding
for the power manager's config registers.
This is part of the OpenTitan watchdog patch series. The power manager
HWIP block needs to be configured to enable the watchdog reset
functionality in the OpenTitan Verilator simulation.
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
The OpenTitan AON Timer is a hardware device that has two features:
the wakeup timer and watchdog timer. This commit series implements the
watchdog feature.
The spec can be found here:
https://opentitan.org/book/hw/ip/aon_timer/index.html
Signed-off-by: Tyler Ng <tkng@rivosinc.com>
This adds support for the USB interface for the
Renesas Smartbond DA1469x device family.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Niek Ilmer <niek.ilmer.aj@renesas.com>
Add an API-less MFD driver for nPM6001. In this case, the MFD device
driver doesn't expose any API as plain I2C API is used within other
device drivers (regulator, GPIO, watchdog). This driver just initializes
some device properties.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
include the infineon,cat1-scb.yaml for I2c and UART bindings to convey
that they are using SCB (Serial Control Block)
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Add a new regulator driver for Analog Devices ADP5360. While it is a MFD
device, only support for BUCK/BUCKBOOST regulators is added in this
patch.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add VREF+ sensor driver and DT node definition.
This driver allows determining the actual voltage applied to an SoC's
VREF+ pin, by comparing the VREFINT internal bandgap voltage reference
with its factory calibration data.
In packages where VREF+ is bonded to VDDA, this permits direct measurement
of VDDA voltage.
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Introduce DesignWare ARC Data Fusion IP Subsystem(DFSS) SPI
driver for ARC boards, i.e. EMSDP, which uses DW SPI to controll
SPI-Flash and DFSS SPI to connect external devices. Both drivers
share most source code, but DFSS uses ARC auxiliary registers.
Move FIFO depth setting to device tree.
Signed-off-by: Siyuan Cheng <siyuanc@synopsys.com>
Renesas Renesas SmartBond(tm) have two ADC blocks:
GPADC and SDADC.
This change adds drivers for both.
Each ADC supports only one channel setup, drivers allow
to have multiply channels in sequence. Switching
between ADC sources in done in software.
GPADC has 10 bit resolution (accuracy can be increase
with oversampling). Values up to 3.6V can be measured
on selected pins. V30 and VBAT1 can also be measured.
SDADC has 14 bit resolution and can take measurements
from 8 pins (single of differential) and VBAT.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Since Merge zephyrproject-rtos#57360, user can use ch<x> and ch<x>N
simultaneously, which is beneficial for STM32 users
working in motor control area.
Signed-off-by: Savent Gate <savent_gate@outlook.com>
Driver was based on can_sam. SAMC21 has only 1 interrupt for one
can "output", so can interrupt has to executes two lines of
interrupts.
CAN is configured to use OSC48M clock via GLCK7. GLCK7 is set
by divider configured from dts.
Signed-off-by: Kamil Serwus <kserwus@gmail.com>
This driver implement basic functions of ili9342c controller
which comes mostly with IPS displays.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
The LSM6DSV16X is a system-in-package featuring a 3-axis digital
accelerometer and a 3-axis digital gyroscope for industrial and IoT
solutions. The LSM6DSV16X embeds advanced dedicated features such as
a finite state machine (FSM) for configurable motion tracking and a
machine learning core (MLC) for context awareness.
https://www.st.com/en/mems-and-sensors/lsm6dsv16x.html
This driver is based on stmemsc HAL i/f v2.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert the NPCX keyboard scan driver to the input subsystem and add the
input to kscan compatibility driver to maintain functionality with the
current API.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add a USB device controller driver skeleton to use as a starting point
for implementing a specific driver.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Example configuration uses 'A' and 'X' key codes for longpress events.
Described behavior shows correct key codes (30 and 45), however comments
near those key codes were invalid for 'X' key. Fix that.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Glitches were observed if a GPIO pin was configured by
ROM to a non-default state and then Zephyr PINCTRL
reconfigured the pin. The fix involves using the correct
PINCTRL YAML output enable and state flags. Reading the
current spin state and reflecting into new pin configuration
if the pin is output and the drive low/high properties are
not present. We also take advantage of GPIO hardware reflecing
the alternate output value in the parallel output bit before
enabling parallel output mode. Interpret boolean flags with
both enable and disable as do not touch if neither flag is
present. We give precedence to enable over disable if both
flags mistakenly appear. Note, PINCTRL always clears the
GPIO control input pad disable bit.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Allows Ethernet communication between "cells"
in the Jailhouse hypervisor.
The vring queue deviates from a standard virtqueue
so is implemented separately.
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
This allows finding the correct PCIe device when multiple devices
have the same vendor-id/device-id but differ in the class-rev register
Signed-off-by: Grant Ramsay <gramsay@enphaseenergy.com>
Add support for partial refresh profiles. This makes it possible to
use partial refresh on generation 2 devices which are able to store
partial refresh LUTs in OTP.
Partial refresh is only enabled if a partial profile has been
provided. The display will use the full refresh profile if in this
case.
Devices that need custom LUTs and voltages can specify them separately
for the full and partial profiles. The controller will be reset when
changing profiles which means that profiles always override the
default reset values. This means that it is, for example, possible to
use default values and LUTs from OTP for a full refresh and a custom
profile for partial refreshes.
For example, to use a GoodDisplay GDEY027T91 with partial refresh
simply use the following device tree fragment:
display: ssd1680@0 {
compatible = "solomon,ssd1680";
spi-max-frequency = <4000000>;
duplex = <SPI_HALF_DUPLEX>;
reg = <0>;
dc-gpios = <&arduino_header 15 GPIO_ACTIVE_LOW>;
reset-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>;
busy-gpios = <&arduino_header 13 GPIO_ACTIVE_HIGH>;
/* Enable the built-in temperature sensor */
tssv = <0x80>;
width = <264>;
height = <176>;
/* Enable partial refresh using built-in LUT */
partial {
};
};
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Update the device tree bindings for the SSD16xx driver to make it
possible to specify multiple refresh profiles.
The only profile currently supported is the 'full' profile.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The SSD16xx driver currently provides basic support for most chips in
the Solomon Systech SSD16xx range of e-paper drivers. We currently use
the SSD1608, SSD1673, SSD1675A, and SSD1681 in various boards
supported by Zephyr.
The main user-facing difference between the various SSD16xx chips is
the resolution they support (sources & gates), but there are other
differences as well. For example:
* 8 or 16 bits used to represent x coordinates
* 8 or 16 bits used to represent y coordinates
* Differences in refresh configuration (SSD16XX_CMD_UPDATE_CTRL2)
* Differences in LUT sizes
The driver currently assumes that the user specifies the number of
bits used to describe coordinates. However, as we add support for more
chips, more of the differences will become apparent and need
workaround.
Comparing data sheets from different chips in the SSD16xx range
suggests that there are (at least) two different generations
present. These differ in the size of the LUTs they expect and the way
they handle partial refresh. This impacts register layout where
SSD16XX_CMD_UPDATE_CTRL2 uses bit 3 selects "mode 2" whereas older
devices uses this for a mode referred to as "initial".
In order to add support for partial refresh in newer devices, we need
to be able to distinguish between the different generations of the
chip. It might be possible to add a DT property to indicate the
revision, but that seems like a bit of an anti-pattern and it would be
hard for users to specify the correct chip generation.
This change introduces chip-specific compatible strings instead of the
generic SSD16xx. There is unfortunately clear pattern that can be used
to distinguish different generations, so the full chip name must be
specified. A benefit of this is that we don't need to specify the
width of the fields describing coordinates in device trees.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Use the same wording in description for both I2C and SPI variants to
improve consistency.
Create st,lsm6dsl-common.yaml to include common binding properties from I2C
and SPI variants.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Update LTDC driver to use LCDIF bindings, to simplify bindings
between LCD interface controller IP blocks.
Boards supporting the LTDC are also updated to use the properties as
declared by the new lcd controller binding
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update MCUX ELCDIF driver to use new LCDIF bindings. This
update also adds support for configuring the root clock of
the ELCDIF module based on the pixel-clock property to the
RT11xx SOC clock init, as this SOC series has this IP block
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update DCNANO LCDIF IP to use shared lcd interface binding. This
requires changes to the RT5xx SOC and RT595 EVK, as this SOC
uses the LCDIF IP, and configures the clock for it based off
the new pixel-clock property.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add common LCD interface binding. This binding captures the
following properties, which are shared between multiple LCD interface
IP blocks:
- VSYNC/HSYNC pulse width
- Vertical/Horizontal front and back porch
- HSYNC,VSYNC,data enable, and pixel clock polarity flags
- pixel clock frequency
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce phy-clock property, which is used by MIPI devices to determine
the target clock frequency for the MIPI PHY. This property can vary
depending on the attached display and target framerate.
Update the MIPI DSI MCUX driver to utilize this property to configure
the MIPI host, and update the RT500 clock initialization to configure
the MIPI root clock based on this property.
Remove dphy-clk-div property from the MIPI DSI 2L binding, as it
is redundant with this change.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Although snps,designware-usb bindings already exist, this one is
prolematic. Compatible is too general and does not reflect
the actual controller IP. It has Zephyr-specific properties,
but has no zephyr prefix. It forces properties that are not
necessary for this controller. We start here with new bare minimum
properties for DesignWare OTG USB 2.0 controller.
The STM32F4 SoC family USB controllers, which are also implement
DesignWare OTG USB 2.0 IP, can also be used with existing drivers,
but require certain quirks. To use these we need special compatible.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add GDMA support for esp32s3.
Remove suspend/resume since they are optional and do
the same as start/stop.
Fix possible null pointer derreference.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Added device tree bindings and implementaion for setting the
spi controllers chip select setup and hold time settings.
Signed-off-by: Dean Sellers <dsellers@evos.com.au>
As recommended in AN4760 the memory region where the QSPI flash can be
memory mapped should be configured to be Strongly ordered memory. This
works around an issue where a speculative read from the CPU may cause
later problems with using the QSPI bus.
This avoids #57466.
Signed-off-by: Ole Morten Haaland <omh@icsys.no>
Most available AT45 flash chips have their first two sectors shorter
than the consecutive ones. Usually, the first sector is marked as 0a
and has its size equal to eight pages (one block) and the second one
(usually 0b) is the complement to the size of a regular sector.
This commits modifies the driver so that erasing of these first two
sectors is performed correctly. This modified behavior is configurable
with a new DT property so that it is still possible to also use legacy
AT45 chips that do not feature such sector split. Such legacy chips
usually also do not support the chip erase and sector erase commands,
so two more DT properties are introduced to cover that.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The LSM6DSO16IS is a system-in-package featuring a 3-axis digital
accelerometer and a 3-axis digital gyroscope for industrial and IoT
solutions. The LSM6DSO16IS embeds a new ST category of processing,
ISPU (intelligent sensor processing unit) to support real-time applications
that rely on sensor data. The ISPU is an ultra-low-power, high-performance
programmable core which can execute signal processing and AI algorithms
in the edge.
https://www.st.com/en/mems-and-sensors/lsm6dso16is.html
This driver is based on stmemsc HAL i/f v2.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
- Added initial version of Infineon CAT1 Flash driver
- Added binding file for infineon,cat1-flash-controller.yaml
- Added overlays for subsys/nvs and drivers/flash_shell
to support cy8cproto_063_ble, cy8cproto_062_4343w boards
- Defined erase-block-size in PSoC6 MPN dtsi.
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
This PR adds a driver for the BMI323, which implements
the following features:
* Enable and disable accelerometer and gyroscope respectively
* Set full scale for accelerometer and gyroscope respectively
* Set data rate for accelerometer and gyroscope respectively
* Get samples (x,y,z) from accelerometer and gyroscope respectively
* Get die temperature
* Set trigger to accelerometer data ready, and accelerometer any motion.
The driver implements device and device runtime power management. If
runtime management is used, it is initialized into the suspended state,
which soft-resets the device to achieve the lowest possible power
consumption, otherwise it is resumed when initialized. When resumed,
the bus is initialized, the feature engine is enabled, and INT1 is
initialized.
The driver only implements the SPI bus at this time. The driver is
prepared to be expanded with I2C support in the future.
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
Add the `full-duplex` property for the `microchip,enc28j60` node.
Replace ETH_ENC28J60_0_FULL_DUPLEX Kconfig option with this property.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Updated the code to to invoke reset using PCR block
z_mchp_xec_pcr_periph_reset() instead of resetting
using I2C Configuration register
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Add the ability for the flash simulator to store its contents in a
memory region.
This allows filesystems on the flash simulator to survive a reboot.
And allows subsystems (e.g. coredump) to store their info on ram while
using the (existing) flash partition backend.
Add a example (for nucleo_f411re) that shows how to configure the flash
simulator for hardware (cfg discussion #54166).
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Add support for a generic NTC, `ntc-thermistor-generic`. In this case,
the compensation table is provided via devicetree. Note that DT property
is prefixed with `zephyr,`, because while hardware related, it is linked
to a particular software implementation.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Refactor driver to align a bit more with its Linux counterpart, ie,
ntc_thermistor. This driver did quite a few _unconventional_ things,
like using "zephyr," compatibles, a dedicated node for pre-computed
compensation table (referenced by the actual pseudo-device node), etc.
The comparison helper function should likely be simplified as well (to
avoid the need for custom wrapper for bsearch), but this can be done
later.
In this refactor, each thermistor gets a compatible, e.g. "epcos,xxxx".
Compatibles are known by the driver, so are compensation tables. This
simplifies devicetree files. There's no need to bother about
compensation tables in **every** board file if Zephyr supports a certain
NTC model.
In general we should respect Linux bindings, which in the end influence
how drivers are implemented. In this case, this principle resulted in
simplified, easier to use code.
For future developers, this is how support for a new NTC can be added:
1. Add to the end of the driver:
```c
#undef DT_DRV_COMPAT
#define DT_DRV_COMPAT vnd_model
static __unused const struct ntc_compensation comp_vnd_model[] = {
{ x, y },
...,
};
#define DT_INST_FOREACH_STATUS_OKAY_VARGS(NTC_THERMISTOR_DEV_INIT,
DT_DRV_COMPAT, comp_vnd_model)
```
3. In driver's Kconfig make sure it depends on
DT_HAS_$DT_DRV_COMPAT$_ENABLED
Note: $X$ means _value_ of X.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
It looks like the Zephyr thermistor driver bindings were half-copied
from Linux ntc-thermistor. Zephyr principle is to maintain compatibility
with Linux, when possible, so there's no reason to deviate here. Convert
the connection type from a custom enum to a boolean, as Linux does.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Initial sensor driver for NPM1300 PMIC charger.
Includes basic configuration of charger voltage and current.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
All Nucleo boards provide the ST Morpho connector/header, which exposes
all pins of the MCU. It is tipically used in ST shields, so provide a
nexus node to allow creating generic shields.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This patch introduces support for NXP S32 CANEXCEL (CANXL) peripheral.
CAN protocol supporting:
- CAN classic
- CAN FD
Remote transmission request is not supported as this feature is not
available on NXP S32 CANXL HAL.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\cy8cproto_062_4343w board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
Added RTC driver that supports Motorola MC146818B
Enabled RTC set/get time and alarm, alarm callback
and update callback.
Counter and RTC uses same hardware in case of
Motorola MC146818, so they can't be used at a time.
Updated stand-alone mc146818 counter dts instances
to support rtc and counter with same compatible
string of "motorola,mc146818" on ia32, atom,
apollo_lake, elhart_lake and raptor_lake platforms.
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
This patch adds support for the TI INA3221 current monitor.
This is the datasheet used for reference:
https://www.ti.com/lit/gpn/ina3221
Since this device has three channels, there is a custom attribute to
select which channel is to be used when getting a sample.
Measurements are done on all enabled channels.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Make it possible to use CPOL/CPHA SPI clock modes with the SDHC driver.
Some cards require the clock to switch to low when not active.
Signed-off-by: Łukasz Hejnak (LeHack) <lehack-ghub@lehack.pl>
Add a binding for STM32 ADC to specify the resolutions and all associated
register information (through a STM32_ADC_RES macro).
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
- Remove build asserts in favor of DT enums
- Remove power level property since it is unused by SDK
- Correct voltage ref value in DT to correspond to
chip specific values documented in reference manuals
instead of corresponding to SDK enum names.
- Fix SOC devicetrees affected by these changes.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This is a new parameter to divide the LPTIM input clock
by a prescaler, changing the max reachable timeout of the LP timer.
It will divide the LPTIM input clock by 1 (reset value) up to 128.
The lptim configuration register is written with a 3bit value.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Implements a UART driver using PIO. Both PIOs are supported.
Only polling API is supported. Only 8N1 mode is supported.
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Added a generic driver for RaspberryPi Pico PIO.
This driver is an intermediate driver for abstracting the PIO
device driver from physical pin configuration.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Signed-off-by: Yonatan Schachter <yonatan.schachter@gmail.com>
Signed-off-by: Ionut Catalin Pavel <iocapa@iocapa.com>
Add STM32WL-specific sx126x_set_tx_params function based on the
STM32CubeWL modifications to LoRaMac-node.
Add the "power-amplifier-output" DT property to
"st,stm32wl-subghz-radio" for selecting between the RFO_LP and RFO_HP
output configurations provided by the above mentioned function.
Add the "rfo-lp-max-power" and "rfo-hp-max-power" DT properties for
defining the maximum design power of the respective outputs' matching
networks.
closes#48511
Signed-off-by: Kenneth J. Miller <ken@miller.ec>
Adds a retention system which builds on top of retained_mem
drivers to allow partitioning of areas and data integrity with
magic header prefixes and checksum of stored data.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
This commit adds the Gecko IADC driver and support for it to the
efr32bg_sltb010a board.
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
- Add Gecko BURTC sys_clock driver to handle wake up from EM2,3 states
- Remove custom PM policy and dependency on HAL sl_power_manager service
- EM1 supported in all configurations
- EM2,3 supported only if SysTick is replaced by BURTC
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
This commit makes the alarms-count dts property of the
rtc-device.yaml optional, setting the default to 0.
This simplifies the dts rtc dts node by not requiring
the property to be set to 0 if it is not supported.
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
- Add initial version of Infineon CAT1 i2c driver.
- Add initial version of binding file for Infineon
CAT1 I2C driver
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
This adds the SPI driver for the Renesas SmartBond(tm) DA1469x MCU family.
The driver only supports controller mode. All four SPI modes are supported.
Note that the lowest supported speed is 2285714Hz.
Requesting speeds higher than 16MHz, will result in a 16MHz SCLK.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Move the devicetree bindings for Analog-to-Digital Converters (ADCs)
from dts/bindings/iio/adc to dts/bindings/adc as Zephyr does not have
an IIO layer.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
On iMX.RT devices, the number of GPIO pins exceeds the maximum of
64 that the PINT interrupt controller can support. Therefore, two
interrupt lines are now shared between the GPIO modules.
This patch allows the user to set the interrupt source for a GPIO
peripheral. For most LPC devices, this will always be the PINT. For some
RT devices, the PINT cannot use pins on GPIO modules other than 0 and 1
as input, and thus the INTA and INTB sources should be used.
Since Zephyr does not support sharing these interrupt between all GPIO
controllers, the user must configure a subset of all GPIO controllers to
use the shared module interrupts. An example of how to do so is provided
for the RT595 EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce PINT driver, for NXP pin interrupt and pattern match engine.
The driver currently supports only the pin interrupt feature of the
PINT.
Add DTS entires for the PINT on LPC and RT devices that support this
peripheral, and remove the interrupt defintions that are PINT specific
from the GPIO module on these devices.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The I2CLCTL_MLCS setting was recently added to MTL
platform. LNL has these registers in separate space, therefore
new field is added to intel,ssp-dai.yaml and appropraite definitions
to LNL device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Repleace usage of shim2 device tree field with hdamlssp.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In current implementation the HDAMLI2SL register is represented by
shim2 field in common SSP device tree file. This could be misleading
since the filed is is different location to I2S IP.
Adding separate device for this register following DMIC case.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
A recent change added the stop-bits and data-bits to the base
uart-controller binding, meaning it's no longer required to
be added in the Altera specific binding.
This requires no further changes because its only use is in
uart_altera.c where only the index of the enum is used,
which remains the same between the new implementation and
how it was previously implemented in the altera specific binding.
Relevant commit: 0234f12
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Add the header file required for the example to work. Users get the
following error due to unresolved INPUT_BTN_* values otherwise:
parse error: expected number or parenthesized expression
Signed-off-by: Amit Kucheria <amitk@kernel.org>
Signed-off-by: Amit Kucheria <amit@mbedrock.com>
These bindings are removed because they are now handled in the
included base uart-controller.yml.
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
Add bindings for LTC1665/LTC1660, which is a 8/10-bit
Digital-to-Analog Converter with eight individual channels.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
This addition should help users to better understand potential issues
with domain clock configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In ACE 2.0 platform (LNL) dmic got two new shim register ranges.
DMIC driver need to program them to configure the interface.
This patch adds new shims to device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
The temperature sensor of the STM32F0x0 is similar to C0 (with one value
for calibration) but uses a negative coefficient, so we add it to the
bindings, just like in st,stm32-temp.yaml
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add a devicetree binding for the CAN-FD capable variant of the NXP FlexCAN
controller. Add example devicetree snippets to both NXP FlexCAN and NXP
FlexCAN-FD binding documentation to limit confusion.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the nxp,kinetis-flexcan devicetree compatible to nxp,flexcan as it
is not specific to the NXP Kinetis series.
This is preparation for adding a nxp,flexcan-fd binding.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add new compatible to separate production calibrated sensors
with single and dual calibration temperatures. Also update
stm32_temp driver to support single calibration sensors.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
Adds support for a devicetree property that controls the ClockDiv
value provided to the SDIO during init.
Signed-off-by: Maxmillion McLaughlin <github@maxmclau.com>
Zephyr SPI driver model for full-duplex operation assumes
data will be transmitted and received during each clock period.
The QMSPI driver for the XEC family also supported dual and
quad I/O use cases which are inherently half-duplex. To
support dual/quad the driver incorrectly processed spi buffers
as all transmit buffers first then all receive buffers. This
worked if only the SPI driver was used. It did not work with
the Zephyr flash SPI NOR driver which assumes SPI drivers
follow the SPI driver model. This commit implements a QMSPI
driver that follows the Zephyr SPI driver model resulting in
a slightly smaller driver. Dual/quad SPI transactions are
supported if the experimental SPI extended mode Zephyr
configuration flag is enabled. We also remove the QMSPI full duplex
driver added previously to support the flash SPI NOR driver.
Added board to spi loop-back test and spi_flash sample.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Arm fvp_baser_aemv8r and fvp_base_revc_2xaemv8a boards are using
SMSC91C111 as their ethernet adapters.
Portions of the codes are based on FreeBSD code from its
'src/sys/dev/smc/if_smc.c' and 'src/sys/dev/smc/if_smcreg.h'.
This driver has two parts, one is the ethernet controller driver, which
is MAC layer driver. The other is the MDIO driver, which is the PHY
layer driver. Both of them are in the same source file due to that they
need to share the same reading and writing register functions and
the smsc object.
The mdio driver is needed by the existing 'phy_mii' driver, which is
a driver for the generic MII-compliant PHY.
This driver was developed under the fvp_base_revc_2xaemv8a target and
has been tested on the fvp_baser_aemv8r target.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
move DT_DRV_COMPAT to bmm150.h. so that can be decide which interface
to use.
define struct bmm150_bus_io interface for bmm150_i2c.c and bmm150_spi.c
in bmm150.h.
redefined bus operation interface in bmm150.c, this allow the driver
to decide which interface to use during construction.
Signed-off-by: Weiwei Guo <guoweiwei@syriusrobotics.com>
Convert the SDL driver to use the input subsystem. This is specifically
meant to emulate touchscreen drivers, so it's setup to send triplet of
x, y, touch for touch-on events and just touch off on touch off events.
Renamed the driver to input-sdl-touch since now we can also develop an
sdl driver for simulating key events.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This commit adds support for ANY_MOTION and DATA_READY interrupts for
the BMI270. To implement this, a different config blob than the
"max_fifo" blob has to be used.
Signed-off-by: Benjamin Lindqvist <benjamin@eub.se>
This adds the i2c driver for the Renesas SmartBond(tm) MCU family.
It supports blocking transfers and callback transfers.
Currently only supports controller mode.
Co-authored-by: Stan Geitel <stan@geitel.nl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Under disk bindings. NVMe is a purely PCIe based technology, thus the
relevant includes.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This adds a driver for the DS2482-800 1-wire multi channel bus driver.
The driver uses a split architecture in order to share a common lock
among all configured channels of a single IC.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Add test for the experimental feature GPIO_ENABLE_DISABLE_INTERRUPT,
which covers APIs gpio_pin_interrupt_enable() and
gpio_pin_interrupt_disable().
Signed-off-by: Sung-Chi Li <lschyi@google.com>
Use the LTDC in combination with the DSI HOST makes the pinctrl obsolete.
DSI HOST has dedicated pins.
Signed-off-by: Rico Ganahl <rico.ganahl@bytesatwork.ch>
The driver has been recently moved under the input subsystem but the
corresponding driver was left over. Move it from kscan to input.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Give precision to the description of the dma phandle in the
quadspi node.
When a DMAMUX is present and enabled, the channel is the dma one
(not dmamux channel) and the request is given by the DMAMUX.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The emulated RTC device driver is used to emulate a real
RTC device. Note that it is not a replacement for the
native_rtc module, which is used to control simulated time,
get time from the host system, etc.
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
This test suite adds tests for the following:
- Setting and getting time
- Validating time is incrementing correctly
- Validating behavior of alarms with callback disabled
- Validating behavior of alarms with callback enabled
- Validating update callback
The test suite uses the devicetree alias rtc to find
the device to test.
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
Add optional filter value properties. The filter is disabled by default
but can be enabled by setting the filter-sample-period > 0 in the dts
file. A latency is introduced if the filter is enabled. The latency can
be printed by setting sensor log level to debug.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
This commit implements the temperature sensor interface for
the Maxim MAX31865 SPI Temperature Sensor.
Signed-off-by: Fin Maaß <fin.maass@haw-hamburg.de>
Co-authored-by: Armin Brauns <armin.brauns@embedded-solutions.at>
In ACE 2.0 platform (LNL) ssp got new shim registers.
SSP driver need to program them to configure the interface.
This patch adds new shims to device tree.
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
This commit adds definition of ACE 2.0 Lunar Lake board.board.
Signed-off-by: Krzysztof Frydryk <Krzysztofx.Frydryk@intel.com>
Signed-off-by: Jaroslaw Stelter <Jaroslaw.Stelter@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Adds tmd2620 driver and devicetree bindings to work in
trigger and polling mode supporting Power management.
Signed-off-by: Peter Fecher <p.fecher@phytec.de>
Add LEDC device for esp32s3
Update PWM LED binding
Remove invalid comment from driver source file
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Enabled simultaneous support by adding a DTS variable named “io-mapped”.
There are 3 possibilities through instance in dtsi file.
Under PCIe, PCIe ns16550.
Under soc and has a variable io-mapped, legacy(IO mapped).
Under soc and don’t have a variable io-mapped, MMIO mapped.
Simultaneous access can be enabled by a Kconfig.
For PCIe instances UART initialization should be done post-kernel as it
depends on PCIe initialization.
Co-authored-by: Najumon BA <najumon.ba@intel.com>
Signed-off-by: Anisetti Avinash Krishna <anisetti.avinash.krishna@intel.com>
Add the `zephyr,pm-device-runtime-auto` flag to `pm.yaml` and
`struct pm_device`.
This flag is intended to signify to the boot system that device runtime
PM should be automatically enabled on the device after the init function
has run.
Only run `pm_device_runtime_auto_enable` function on a device if
initialisation succeeded. This prevents actions being run on devices
that are not ready.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Added a new watchdog driver which can handle a multiple wdt_dw instances
and can control the pause signal.
The mlt platform has three designware watchdogs, one for each core.
I decided to create a separate intel watchdog driver for the following
reasons:
1. All three devices share the same interrupt number. Each watchdog reports
an interrupt to the core to which it has been assigned. The same interrupt
number cannot be used by multiple devices in the device tree. So, it would
be assigned to only one device. The other dw watchdog devices would use
this assignment, even though it would not be described for them in the dt.
The interrupt handler function in dw watchdog checks the interrupt flag.
If the interrupt was connected to the first watchdog, and the second or
third watchdog signal an interrupt, the interrupt handler of the first
device would ignore it because it would not have set the interrupt flag.
The watchdog device don't knows anything about the existence of the others
devices.
2. The designware watchdog only supports a hardware pause signal. It cannot
be paused programmatically. On the mtl platform, there is a separate group
of control registers for all per-core watchdogs. There are GPIO-like
registers that allows control of a hardware pause signal for subordinate
watchdogs. This separate block is shared by all three watchdogs.
3. The base addresses of the subordinate watchdogs are read from the
aforementioned control registers. As a result, in the device tree we have
only one base address for the intel watchdog, which points to the pause
control registers and containing the base addresses of the subordinate
devices.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Add a driver that listens for input events and reports them on a kscan
API. This allows porting kscan drivers to the input APIs while
maintaining compatibility with the existing kscan based applications.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This patch makes possible to choose custom byte which should be used
to enable non-permanent readout protection (RDP1). Actually, any byte
except 0xAA and 0xCC (which are used by RDP0 and RDP2 respectively)
can be used to enable RDP1 but in multi-image environment, some other
image could check if RDP1 is enabled by comparing it to some hardcoded
value.
If property is not defined, 0x55 will be used to enable RDP1. The
default value comes from STM32 HAL.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
Update DMA bindings with DMA config macros
only for st,stm32-dma-v2.yaml and st,stm32-dma-v2bis.yaml
Signed-off-by: Marc Desvaux <marc.desvaux-ext@st.com>
Adds the new stm32h5 serie to the list of st,stm32g0-exti
compatible : now the matching targets is C0/G0/H5/U5/L5/MP1.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add binding and sensor attribute to allow single phase
mode where only one signal is required from the encoder.
The signal must be connected to Phase A input.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add a GPIO nexus binding for Pmod interface connectors.
This commit also includes a header file with macros
that map signal names in the Pmod specification to
the corresponding indices in the GPIO nexus, meant for
use in devicetree files.
Signed-off-by: Alexander Mihajlovic <alexander@eub.se>
Add an input device to take input key events as an input and generates
short press or long press devices as output.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The number of available EasyDMA MAXCNT bits is now defined per-instance
in Devicetree.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Change device tree VW routing to a form allowing overrides.
Add two new DT optional properties for specifying the reset
source and reset value of each virtual wire. Only virtual
wires that are enabled using the status property are modified.
NOTE: eSPI virtual wires are controlled in groups of 4 by
hardware. The optional reset signal source properties applies
to all four virtual wires in the group. If this field is
changed from the hardware default, it should be changed for
only one virtual wire in the group. If the property exists
in more than one wire in the group it must be set to the
same value.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Modify Mircrochip MEC172x eSPI driver to get eSPI virtual wire
hardware routing from device tree.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The clock control driver requires three pieces of information:
PCR register index, bit position, and clock domain. Clock domain
was missing from DT information and MCHP macros.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Deleted adc_mchp_xec.c and microchip,xec-adc.yaml file.
DTSI, yaml, CMakeLists.txt and Kconfig.xec files are
updated for compatible.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Updated the "adc_mchp_xec_v2.c" adc driver to support both MEC172x and
MEC15xx SOC.
ADC smapling clock configuration updated using DTS.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
The regulator driver has a configured min/max range that is used
to limit set values, and to initialise the regulator.
A new init value has been added, so that the startup voltage can
be higher than the lowest permitted value.
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
Added initial version of Infineon cyw43xxx BT (
H4 HCI extension drivers/bluetooth/hci/CMakeLists.txt)
Add initial version of binding file for Infineon CYW43xx BT
HCI extension driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
This adds a basic Intel TCO watchdog driver. The driver doesn't support
windowed timeouts (a non-zero window.min value) or callbacks. The driver
currently assumes TCO version 6, which can be found e.g. on Elkhart Lake
and Raptor Lake platforms. The driver also expects the TCOBA base
address to be specified through DTS, rather than doing runtime lookup
(using e.g. ACPI or PCIe).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remedial rework to handle the enabling of the I2S master clock
output based on the presence of an introduced DT property.
For details see issue/54841.
Signed-off-by: Raul Pando <raul.pando@bytegrity.co.uk>
Add initial version of clock control for Atmel SAM SoC series. This add
support to Power Management which allows control peripherals clock.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add support for the TI TPS382x series. The IC has an input pin which
should be toggled by the processor and a output pin which should be
connected to the RESET input of the processor. The timeout is not
configurable.
This device can be used by devices which does not have any internal
hardware watchdog device.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Modifying counter drivers (rtc and timer) to rely completely on
device tree and not on Kconfig of MDK flags.
Adapting dtsi for all SoCs and adapting test configuration.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Adds a driver for the Nordic nRF GPREGRET registers and adds
entries to the SoCs for this peripheral.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Add support for virtual UART device that uses ARC Hostlink channels
for data transfers. Due to the Hostlink principle, this driver
supports only polling API.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
This symbol allows users of the driver to disable the
power management feature of just this sensor if they are
not using the int_gpios pin of the BQ274XX.
Signed-off-by: Nick Ward <nix.ward@gmail.com>
interrupts property was previously added with "required: false", but
when required was removed (redundant), the interrupts property was left
dangling.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
To enable Bluetooth controller coexistence feature, there is
implementation of ticker task, which aborts any ongoing radio events
during assertion of the grant pin. This solves the co-existence issue
in the role of the subordinate transceiver.
Signed-off-by: Tomáš Beneš <tomas@dronetag.cz>
The zephyr,gpio-keys is now emitting input events, so it makes sense to
require a key code to be set. Change the zephyr,code property to be
required and add an example in the binding description.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Port the gpio_keys_zephyr driver from the gpio subsystem with a
dedicated API to the input subsystem reporting input events.
Move the test as well, simplify the cases a bit since the API is simpler
now.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The 200ns reset time specified in the datasheet are a minimum time; and the
nanoseconds were being rounded to whole microseconds anyway.
Also make it the same type as `config_delay_us` (`uint16_t`).
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
From FPGA-TN-02001-3.3 "iCE40 Programming and Configuration":
> After driving CRESET_B High or allowing it to float High, the AP must
> wait a minimum of 1200 µs, allowing the iCE40 FPGA to clear its internal
> configuration memory.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
The board embeds an audio codec IC, Cirrus CS42L73. While there is no
in-tree driver for it, we need a binding to describe how it is wired in
the board, e.g. for IRQ/RESET lines.
Following Linux binding for the same IC, create one in
dts/bindings/sound. Note that Linux binding is less complete/outdated.
Ref. https://statics.cirrus.com/pubs/proDatasheet/CS47L63_DS1249F2.pdf
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add driver for Xptek XPT2046 resistive touch controller on SPI.
Only interrupt driven mode supported, does not do polling.
Signed-off-by: Seppo Takalo <seppo.takalo@iki.fi>
Introduce driver for NXP DCNANO LCDIF (lcd interface) peripheral,
present on iMX.RT500. Currently this driver only supports updating
the primary framebuffer, and does not implement support for the cursor
buffer present on this IP.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce driver for MCUX MIPI DSI 2L. This IP block differs slightly from
the existing MCUX MIPI peripheral, and uses a different hardware
abstraction layer. For these reasons, a new driver was introduced rather
than extending the existing mcux_dsi implementation.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Allow configuration of AHB RX buffer allocation. This allows sections
of the AHB RX buffer to be reserved for specific masters, which can
enhance performance.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The driver utilizes ST Microelectronics library (which
exists in modules\hal\st\sensor\vl53l1x. Platform specific
headers and source files used by the library are included
and adapted for Zephyr.
The driver can be configured in proj.conf to use a
interrupt/polling methods and the use of the XSHUT pin on
the VL53L1X. All uses were tested successfully.
Signed-off-by: Mark Watson <mwatson@prosaris.ca>
This patch adds watchdog driver for Renesas Smartbond SOCs.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
This adds driver for SmartBond TRNG peripheral that with separate
ISR an thread data pools.
Co-authored-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Add support for configuring power on delay when using SPI SDHC. This
allows cards that reliably initialize with a shorter (1ms) delay to
avoid the long initialize delay otherwise imposed.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add I2C bus recovery support to the STM32 v1 and v2 driver. The STM32 i2c
peripheral does not natively support I2C bus recovery so recovery is
performed using GPIO bitbanging. This mirrors the bus recovery
implementation for NXP MCUX LPI2C driver.
Fixes: zephyrproject-rtos#54917
Signed-off-by: Maxmillion McLaughlin <github@maxmclau.com>
Added initial version of Infineon CAT1 GPIO driver.
Added initial version of binding file for Infineon CAT1 GPIO driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Infineon CAT1 UART driver.
Added initial version of binding file for Infineon CAT1 UART driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Added initial version of Infineon CAT1 Pin controller driver.
Added initial version of binding file for Infineon CAT1 Pinctrl driver.
Added initial version of dt header for Infineon CAT1 pinctrl driver.
Signed-off-by: Nazar Palamar <nazar.palamar@infineon.com>
Provide dts binding for F412 PLL I2S.
This I2S dedicated PLL is fully configurable and take same
input as Main PLL
Only one output clock (PLLR) is supported for now.
This PLL could be found on STM32F412 and F413 parts for instance.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Provide dts binding for F4 PLL I2S.
This PLL share input source and input M diviso with F4 Main PLL.
Only one output clock (PLLR) is supported for now.
This PLL could be found on STM32F401 parts for instance.
Additionally, provide related header definitions.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Polarity support added to XEC PWM driver. This allows (for example) PWM
controlled LEDs that are active low to actually be turned off when set
to off.
Signed-off-by: Jeff Daly <jeffd@silicom-usa.com>
Rework the Host Command support. It includes:
-change API to backend
-change a way of defining rx and tx buffers
-fix synchronization between the handler and backend layer
-simplify the HC handler
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Follow naming pattern in the subsystems(logging or shell) and name
the layer between generic handler and peripheral driver "backend".
The name doesn't suit that well to the SHI backend, because there isn't
SHI API itself and the SHI interface is used only for the host
communication. So the backend code includes the peripheral driver itself.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add the implementation for the akm09918c magnetometer driver.
Additionally, add the appropriate node to the TDK robokit1 device
tree. In order to prevent regressions, add the sensor to the sensor
build_all tests and specific tests using an emulator.
Signed-off-by: Yuval Peress <peress@google.com>
Add a driver implementation that uses the I2S peripheral.
Based off this blog post:
https://electronut.in/nrf52-i2s-ws2812/
Should help with #33505, #29877 and maybe #47780, as there is no garbage
data at the end of transmissions on nRF52832, and no gaps.
Signed-off-by: Jonathan Rico <jonathan@rico.live>
STM32L4plus mcu has SDMMC internal DMA which works without any
configuration and it's handled by SDMMC HAL driver. This commit adds
option to enable it and use it.
Signed-off-by: Petr Hlineny <development@hlineny.cz>
Create and use a new `zephyr,i2c-target-eeprom` compatible
within I2C eeprom target driver that allows to use
that driver along with real atmel at24 EEPROM simultaneously.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Update machine timer drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on NIOSV devicetree.
Signed-off-by: Khor Swee Aun <swee.aun.khor@intel.com>
This commit adds access to the string values without a quotes.
Signed-off-by: Radosław Koppel <r.koppel@k-el.com>
Co-authored-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
This commit adds support for BH1750 ambient light sensor.
The driver works using I2C peripheral in one-time mode.
Signed-off-by: Michal morsisko <morsisko@gmail.com>
The Microchip XEC (MEC172x and MEC152x) have a breathing-blinking
LED (BBLED) block which implements a simple PWM mode. The BBLED
PWM frequencies are 32KHz and 48MHz selectable in device tree.
Frequency divider is 12-bit resolution from 256 to (256 * 4096).
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The Microchip XEC family of microcontrollers includes a
simple DMA block implementing multiple channels. DMA supports
memory to memory, memory to peripheral, and peripheral to
memory transfers. Peripheral support is limited by each
chip to I2C and SPI controllers. DMA hardware does not support
scatter-gather or linked transactions.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Align driver with changes introduced in the hal. `nrf_timer_frequency_set`
was changed to `nrf_timer_prescaler_set`, update driver accordingly.
Signed-off-by: Adam Kondraciuk <adam.kondraciuk@nordicsemi.no>
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
New Zephyr WDT driver for TI CC13xx/CC26xx family.
Supports interrupts & MCU soft reset on timeout.
Signed-off-by: Stancu Florin <niflostancu@gmail.com>
Each GPIO controller may contain GPIO hog definitions. GPIO hogging is a
mechanism for providing automatic GPIO configuration during system
initialization.
Each GPIO hog is represented as a child node of the GPIO controller.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
changes to support low power and wake support in microchip xec uart
driver. Add support for wakerx_gpio config in dts to select the wake gpio.
Configure for wake in PM_DEVICE_ACTION_SUSPEND state and clear
interrupt in wake isr. Also added support for
CONFIG_UART_CONSOLE_INPUT_EXPIRED
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Boolean properties for STM32 ADC internal channels are not used anymore
and can be removed. It is replaced by channel number properties.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add some bindings to define STM32 ADC internal channels for:
- Temperature
- Vref
- Vbat
The goal is to transfer information to the dts instead of inside the
ADC driver.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Bugfix for the Cyclone V SoC DK ethernet driver need to add emac-index
in dts
- We remove the "local-mac-address" property from
dts/arm/intel_socfpga_std.dtsi to
boards/arm/cyclonev_socdk/cyclonev_socdk.dts, since this value is
dependant on the board / implementation and not universal to
the "intel_socfpga" package that it inherets from.
- The above is also true for the "status" property as the board
should enable the device.
Signed-off-by: Benjamin Kyd <benjamin.kyd@intel.com>
Add three xbar nodes and four qdec nodes in the rt10xx devicetree include.
Add xbara to rt1052 in Kconfig.soc
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add a driver for the NXP MCUX Quadrature Decoder. The driver
is simple and only implements the phase a and phase b inputs. The
module has additional features which can be added in future PRs.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Change the name of the custom macro defined for the stm32 devices
to fit the VND_PWM_xxx model
Keeping old deprecated macro, though.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Introduce Ethernet low-level driver for NXP S32 Network Controller
(NETC). Current driver allows to manage from Zephyr a Physical Station
Interface (SI) and/or a Virtual SI. The NETC has an integrated Ethernet
Switch. Currently the Switch is initialized from this driver with a
default configuration, and all ports are enabled and transparent for
the user. A separate Switch driver should be addressed in future patches.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Introduce NXP S32 NETC External MDIO controller driver. Driver supports
a single instance, as current support is based on NXP S32Z/E SoCs.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Introduce NXP S32 Message Receive Unit (MRU) driver based
of Mbox API. The MRU couples with a processor and allows to
receive messages from senders, which are other modules or
processors.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Add 2 properties in STM32 external interrupt controller:
- num-lines
- line-ranges
Additionally, make interrupt-names a required property.
The properties will help to simplify exti init code in building the
exti_irq_table and simplify the isr related bits.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Intel DSP Communication Widget is a device for generic sideband
message transmit/receive between IPs in a SOC.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
The interrupt is used to wake up EC from low power mode.
So EC does not defer eSPI bus while transaction is accepted.
Fixes EC host commands slow issue.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
This commit makes the peripheral-id property optional and removes it's
usage from the Gecko SPI driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
The documentation for the fixed-partitions binding is missing critical
information and is vague in other important respects. This is an
important binding that deserves to be crystal clear. Fix it.
Signed-off-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Add kscan pins gpio driver for KSI[7:0], KSO[15:0] pins that
they can be configured to gpio mode. These pins registers address,
bit fields and function are different from GPIO group, so I create
a new compatible driver for these pins.
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
- Adds the declaration of the MMC API
- Adds MMC spec related declarations
- Adds some properties to sdhc dts binding for mmc
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
- Adds the pin controls and ushdc settings in device tree
- Attaches clock to USDHC in soc.c
- Adds binding for mmc
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
While nPM1100 is to be operated in fixed configuration for some
applications, it has some degree of configuration via GPIOs. For
example, mode (auto/PWM) can be configured via MODE pin. VBUS current
can also be adjusted using ISET pin, even though there is no API yet to
limit the PMIC input current.
This patch adds a new regulator class driver for nPM1100 PMIC, so that
it can be used with the standard regulator API when needed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit adds the support for host commands being transported
by the Serial Host Interface on the IT8xxx2 SoC.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
This commit adds the support for host commands being transported
by the Serial Host Interface on the NPCX SoC.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
Adds a driver for TDK InvenSense 42688 six axis IMU. Verified using
the sensor shell sample app via:
- sensor info
- sensor get icm42688p@0
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Signed-off-by: Yuval Peress <peress@google.com>
Add a st,static-prescaler optional property to DTS
of the stm32 where the LPTIM has a x2 factor on
its clock input.
This property is present or not depending on the stm32.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Drop compatible from fuel-gauge.yaml, it's not needed since this binding
is not meant to be used directly, and is also incorrect as it includes
the "yaml" suffix.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Purpose of this node is only to provide a way to configure RF
clock using device tree and clock_control driver.
Default configuration is reproducing existing hard-coded configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Introduce driver for APS6408L PSRAM, built on top of the MCUX memc
driver for flexSPI. This driver supports operating the PSRAM in high
speed mode (200MHz or more). Note that in order to support this
PSRAM's alignment requirements, either ahb-read-addr-opt or
ahb-prefetch must be set for the FlexSPI instance.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Rename flexspi-hyperram driver to flexspi-s27ks0641, and update
function names. This driver is only capable of supporting the
s27ks0641 HyperRAM chip, as the lookup table given in this driver
is specific to the s27ks0641.
Rename the flexspi-hyperram binding to reflect this, to
prevent confusion from users.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fix all line-length errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(line-length)'
Using a limit is set to 100 columns, not touching the commandlines in
GitHub workflows (at least for now).
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix all comments-indentation errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(comments-indentation)'
This checks that the comment is aligned with the content.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix all hyphens errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(comments)'
Default config would be to require two spaces after the start of the
comment, proposing to keep it on 1, inline with the Linux binding
config, that is:
```
- comments:
- min-spaces-from-content: 1
```
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix all hyphens errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(hyphens)'
Default config is only one space after the hyphen.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix all brackets errors detected by yamllint:
yamllint -f parsable -c .yamllint $( find -regex '.*\.y[a]*ml' ) | \
grep '(brackets)'
Default config is to have no spaces inside brackets, changed few
documentation strings as well that refered to lists even though the
linter does not care about those.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix Microchip XEC clock control driver single-ended XTAL2 pin
initialization. Add support for external 32KHZ_IN pin as a
clock source including PINTRL to switch the GPIO to 32KHZ_IN
function. Add device tree option to disable internal silicon
oscillator if it is not required by the configuration. Add
device tree tuning options based on crystal and board layout.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add config cell property to gd,gd32-dma.
For supporting hardware variation, Splitting base definition
to gd,gd32-dma-base.yaml.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
peripheral-id property should be eventually removed.
For now set it as optional and allow skipping the usage
in UART driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
peripheral-id property should be eventually removed entirely.
For now set it as optional and allow skipping the usage
in GPIO driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@antmicro.com>
This commit adds initial support for Silabs Real-Time counter
Co-authored-by: Filip Kokosinski <fkokosinski@antmicro.com>
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
This commit adds a series of driver-related changes to
Gecko pinctrl.
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
This commit adds initial support for gecko pinctrl driver
Co-authored-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The ADC module has four conversion groups, each one is set up as a zephyr
device. The start-up calibration is initiated globally for all groups
and it is run in each device init function. The ADC module supports post
calibration per group. Post calibration is run automatically after each
group acquires the samples.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Add FFF-based fake regulator driver. This driver can be used as a stub
or mock in testing.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
These inherited properties from Linux bindings are not supported yet.
The reason for the removal is because regulator-couple-with requires
definition of #cells spec, unless bindings explicitely ban the property
or use allowlist.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add support for virtual USB host controller intended for use
together with virtual bus and virtual device controllers.
This driver is not an emulation of any real host controller.
The driver has initial support for handling control and bulk
transfers.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add support for virtual USB device controller intended for use
by virtual bus and virtual UHC controllers. This driver is not
an emulation of any real host controller.
The driver has initial support for handling control and bulk
transfers.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add common layer of UHC API and MAX3421E host controller driver.
This implements the bare minimum necessary to communicate with
one peripheral device.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Support for the measuring the CPU die temperature
for the ESP32 targets S2,C3. The ESP32 support
was ommited due to lack of offset calibration.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Serial speeds listed in device tree did not reflect
what driver supports.
2M and 500K were missing while
1200, 2400 and 460800 were present while not supported.
This change synchronized dts with driver code:
drivers/serial/uart_smartbond.c
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
PCA9420 PMIC offers of multiple operation states, or DVS (Dynamic
Voltage Scaling). Such states may be automatically changed by hardware
using MODESEL0/1 pins. Certain MCUs allow to automatically configure
certain output pins when entering low power modes so that PMIC state is
changed without software intervention. This means that application just
needs to configure the voltages for each state using
`nxp,modeN-microvolt`, set `nxp,enable-modesel-pins` in devicetree and
forget about configuring regulators.
This patch introduces a new _parent_ API to expose such functionality in
a vendor agnostic way. Consider this API as experimental for now, until
we have other usecases.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Most of devicetree properties for regulator, such as:
- regulator-min/max-microvolt
- regulator-min/max-microamp
- regulator-allowed-modes
- etc.
Are meant to specify limits on what consumers may set. They are **NOT**
meant to describe the hardware capabilities. For example, I could have a
BUCK converter that supports 0-5V output voltage, but my circuit may
only allow working on the 2.7-3.3V range.
This patch reworks the API so that the API class layer manages this
information. This is done by drivers collecting all such fields in a
common configuration structure that is later accessed by the class
layer. This simplifies drivers implementation. For example, if A
consumer calls regulator_set_voltage() with a voltage that is supported
but not allowed, driver code won't be called. Similarly, if a regulator
is configured to be `always-on`, enable/disable driver code will never
be called.
Drivers have been adjusted. PCA9420 mode settings have been removed from
devicetree in this commit as they are not actual modes but PMIC states.
This will be refactored in a follow-up commit.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The XY Memory is a feature commonly found in DSP processors to increase
the DSP performance. The XY component allows a ARC processor to
implicitly load source operands and store results into a closely coupled
memory using a single instruction.
Add XY memory for ARC EM9D/EM11D processors including em_starterkit,
em_starterkit_em11d. emsdp_em9d, nsim_em, iotdk.
Signed-off-by: Siyuan Cheng <siyuanc@synopsys.com>
In Infineon XMC4XXX SoCs, gpio interrupts are triggered via an
Event Request Unit (ERU) module. A subset of the gpios are
connected to the ERU. The ERU monitors edge triggers and creates
a SR.
This driver configures the ERU for a target port/pin combination
for rising/falling edge events. Note that the ERU module does
not generate SR based on the gpio level. Internally the ERU
tracks the *status* of an event. The status is set on a positive
edge and unset on a negative edge (or vice-versa depending on
the configuration). The value of the status is used to implement
a level triggered interrupt; The ISR checks the status flag and
calls the callback function if the status is set.
The ERU configurations for supported port/pin combinations are
stored in a devicetree file dts/arm/infineon/xmc4xxx_x_x-intc.dtsi.
The configurations are stored in the opaque array
uint16 port_line_mapping[].
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
The interrupt-map property specifies both 32-bits values and a phandle;
update the type accordingly.
Update the definition of pcie-host-ecam-generic on qemu arm64 to match
the new type.
Signed-off-by: Rodrigo Cataldo <rodrigo.cataldo@huawei.com>
Co-authored-by: Henri Xavier <datacomos@huawei.com>
Add DTS information for qemu-virt-a53 and qemu-kvm-arm64 for PCIe
controller support. Three new bindings are required for the PCIe
controller in ECAM mode.
The DTS information was extracted from QEMU (dumpdtb) with a PCIe device
attached to the virtual machine (ivshmem)
Signed-off-by: Rodrigo Cataldo <rodrigo.cataldo@huawei.com>
Co-authored-by: Henri Xavier <datacomos@huawei.com>
We are about to add UART reset during driver initialization. First step
is to add 'resets' property, which provides information about reset
register offset and bit.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
We are about to add timer reset during driver initialization. First step
is to add 'resets' property, which provides information about reset
register offset and bit.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
To deassert reset in STM32MP1 RCC the driver needs to set the bit in
reset clear register.
This patch extends existing implementation to support this type of
register.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
This driver exposes STM32 RCC reset functionality through reset API.
Information about RCC register offset and bit is encoded just like GD32.
The first 5 least significant bits contains register bit number.
Next 12 bits are used to keep RCC register offset. Remaining bits are
unused.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
STM32 battery-backed RAM is organized in 4 byte registers. Number of
registers can vary between models from 5 to 32 registers.
Usually, the registers are part of RTC. On some variants they are part
of tamper module. On STM32F1 the registers are in separate module. For
now, only backup registers from RTC are supported.
Signed-off-by: Patryk Duda <pdk@semihalf.com>
NXP LPUART IP supports rs485 mode when transceiver driver enable
using RTS. Allow setting rs485 mode up via the "nxp,rs485-mode"
dts property. "nxp,rs485-de-active-low" dts property can be used
for set RTS polarity.
Signed-off-by: Grixa Yrev <GrixaYrev@yandex.ru>
- Similar to what was done for other parts of the driver, remove any
register specification from Devicetree (modesel-reg/mask)
- Keep all the information in the driver, and define modes as "numbers",
e.g. PCA9420_MODE0: 0, PCA9420_MODE1: 1, etc.
- Bindings provide IC defaults now (all modes allowed 0/1/2/3 and
initial mode set to 0).
- When mode is controlled via the MODESEL0/1 pins (ie directly by an iMX
MCU using the dedicated PMIC_MODE0/1 pins), the driver will not allow
to select a mode (it is not possible). This mode is now enabled by
setting `nxp,enable-modesel-pins` in Devicetree. When enabled, all the
allowed modes are configured to be selectable via pins. When disabled,
mode can be set via I2C (using TOP_CNTL3 MODE0/1_I2C fields)
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add bindings for Aspeed AST10x0 reset driver. The reset line can be
de-asserted or asserted through the syscon registers.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Add RX and TX fifo size properties to CDC ACM UART bindings.
This allows per instance settings in contrast to Kconfig
USB_CDC_ACM_RINGBUF_SIZE option. New properties takes the default
size value of USB_CDC_ACM_RINGBUF_SIZE which can be removed
subsequently.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add rgb-is-inverted option to indicate module's pixel-format is
inverting from MADCTL settings of ST7735R controller.
This option intends to implement a workaround for LCD modules
that is the actual screen color was different (inverted)
from the RGB setting in MADCTL property.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Implement a LED driver for Microchip XEC using the breathing,
blinking LED controller. The driver supports LED on, off, and
blink API's. The BBLED block uses the 32768 Hz clock domain
allowing the module to operate in light and deep sleep states.
Blink frequency is 32768 divided by 256 * (prescale + 1) where
prescale is a 12-bit value. Duty cycle is specified by an 8-bit
value where 0 = full off, 127 is 50%, and 255 is full on.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove regulator-fixed-sync specialization, create a single driver that
is always synchronous. The asynchronous part is rarely/never used, so
let's keep things simple for now.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
NXP S32 System Timer module includes a 32-bit count-up timer and four
32-bit compare channels with a separate interrupt source for each
channel. The timer is driven by the module clock divided by an 8-bit
prescale value.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Microchip XEC GPIO pins support inverting the output of
alternate pin functions. This feature may be useful for
those peripherals that do not implement output inversion
in the peripheral. GPIO control register pad input and
parallel input register values are not affected by the
function output invert feature. GPIO interrupt detection
of an output is inverted if the invert polarity is enabled.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
add Intel HDA DAI driver
Long device list in dtsi needs to be refactored in the future
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
The driver had a conceptual issue regarding current limitation. PCA9420
is able to limit the current flowing through VIN, ie input current. This
is a global setting, not individual to each regulator. This patch
creates a new DT property: nxp,vin-ilim-microamp to specify such limit.
It is applied when the device is initialized.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Voltage ranges were hardcoded in Devicetree, however, things can be
significantly simplified by using the recently introduce linear ranges
API. All values are now computed using information stored in the driver,
so there is no need to store any lookup table in ROM. Code should now
both be faster in average and consume less ROM.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Maximum current was not specified. Even though not used, yet, it is a
valuable information. Values taken from PCA9420 datasheet, Figure 1
"Simplified block diagram".
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Regulator registers were set for each BUCK/LDO in DT, likely because of
the way the devices were instantiated. When using a generic iterator,
ie, DT_INST_FOREACH_CHILD, there's no way to differentiate the child
being _parsed_. Since instantiation happens now based on child node
names, we are able to know which registers each devices gets assigned at
the driver level. This greatly simplifies Devicetree, and it actually
removes information that is not strictly hardware description from it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Right now the PCA9420 driver instantiates by iterating over all
children. This is somewhat problematic, for a few reasons:
- Since instantiation is generic code, we're forced to put internal
details on Devicetree, e.g. reg-masks. After this change, this will no
longer be necessary.
- We take all children, regardless of what is defined in DT.
While we have no means to validate Devicetree node names as in Linux
dtschema, this approach allows us to have per-child specific
initialization code. This is somewhat similar to the Linux approach.
Note: nodelabels have been removed, since they were not used.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
regulator-allowed-modes/regulator-initial-mode are standard properties
defined in regulator.yaml, so use them.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Import all Linux properties, so that we can maximize compatiblity with
upstream bindings.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Following Linux regulator.yaml, regulator-name is a common property for
all regulators.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The sdhc-spi-slot requies an spi bus, but sd nodes (like sdmmc-disk)
cannot be added to it without a warning because it does not declare an
sd bus.
Signed-off-by: JP Sugarbroad <jpsugar@amazon.com>
RT1718S is an i2c-based TCPC chip that supports 3 additional GPIOs.
The pins can be used for USB-C operations e.g. handling FRS, but they
can also work as usual GPIOs.
Add a driver for the RT1718S GPIO and a handler for an alert signal from
the chip. The handler reads the alert register once asserted and calls
the GPIO interrupt handler if needed(Vendor-defined alert).
gpio_rt1718s.c file and "richtek,rt1718s" node collect common properties
and data for all RS1718S functionalities. The file can be extended for
TCPC driver. rt1718s.h file also defines inline functions with i2c
operations common for all drivers. The common header and source files
can be moved to tcpc directories once the tcpc driver is added since it
is the main functionality.
Signed-off-by: Dawid Niedzwiecki <dn@semihalf.com>
Add drdy_pulsed property in Device Tree in order to select how
data ready irq should behave (either pulsed or latched mode).
Moreover change/fix the API called to set drdy irq mode.
(fix#51944)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Since we can include other binding files at any level (child,
grand-child, etc.) it makes no sense to maintain two copies of pinctrl
props definitions (pincfg-node/pincfg-node-group). Instead,
pincfg-node.yaml defines props at root level, and it is included where
needed, either child-binding or grandchild-binding.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Added to the device tree values of the dma-copy-alignment
and dma-buf-size-alignment attributes.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
dma-buf-size-alignment: Buffer size alignment required by the DMA
controller.
dma-copy-alignment: Minimal chunk of data possible to be copied
by the controller.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
Renamed the dma-buf-alignment field to a more explicit
and descriptive name dma-buf-addr-alignment.
Signed-off-by: Adrian Warecki <adrian.warecki@intel.com>
No sfdp-table property given by the DTS but received from
the octoflash Node rely on the issued by the read sfdp command.
Note that the size of the mx25lm51245 flash controller
is expressed in bits (ie 512Mbits or 64 Mbytes).
Signed-off-by: Francois Ramu <francois.ramu@st.com>
DTS property attributes are (by default) not required.
Explicitly specifying `required: false` is redundant.
Perhaps a warning to that effect would be useful.
Signed-off-by: Chris Friedt <cfriedt@meta.com>
Add a sample sbs gauge driver with feature parity and basic tests
comparison to its sensor counter-part. Includes a simple stub test that is
extended upon.
Signed-off-by: Aaron Massey <aaronmassey@google.com>
Added support for fxas21002 sensor over SPI bus on
RDDRONE board and proper selection through dts.
Tested with fxas21002 sensor on RDDRONE.
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Co-authored-by: Sumit Batra <sumit.batra@nxp.com>
Added support for fxos8700 sensor over SPI bus on
RDDRONE board and proper selection through dts.
Tested with fxos8700 sensor on RDDRONE.
Signed-off-by: Benjamin Perseghetti <bperseghetti@rudislabs.com>
Co-authored-by: Sumit Batra <sumit.batra@nxp.com>
Use the new PCIe core infrastructure for looking up the BDF at runtime
based on the VID/DID values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the new PCIe core infrastructure for looking up the BDF at runtime
based on the VID/DID values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the new PCIe core infrastructure for looking up the BDF at runtime
based on the VID/DID values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the new PCIe core infrastructure for looking up the BDF at runtime
based on the VID/DID values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use the new PCIe core infrastructure for looking up the BDF at runtime
based on the VID/DID values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BDF values can differ on the same platform, based on e.g. BIOS
configuration, and in the case of qemu the command line parameters. It's
therefore more reliable to always look up the BDF value based on the
known Vendor and Device IDs.
This patch introduces such a framework, and allows the incremental
update of PCIe drivers to start taking advantage of it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add property mxicy,mx25r-power-mode to jedec,spi-nor binding for
controlling low power/high performance mode on Macronix MX25R* Ultra Low
Power flash devices.
- "low-power" configures the flash in ultra low power mode.
- "high-performance" configures the flash in high performance mode.
Signed-off-by: Gregers Gram Rygg <gregers.gram.rygg@nordicsemi.no>
Updating mps3_an547 board files with DTB entries for Ethos-U.
Adding DTS bindings for the Ethos-U DTB entry.
Signed-off-by: Kristofer Jonsson <kristofer.jonsson@arm.com>
Signed-off-by: Fredrik Knutsson <fredrik.knutsson@arm.com>
The sensor uses the ALERT terminology (pin can be configured to trigger
on certain events such as conversion ready or overvoltage alerts). The
"IRQ" name is not clear.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify the units of the current LSB in microamperes, so that we can
measure low maximum currents. Right now it was specified in
milliamperes, but ignored and always hardcoded to 1mA in the driver.
This makes the driver pretty much useless when the maximum current to be
measured is in a range of e.g. 20-50mA.
This patch also removes some unnecessary ifdeffery: since we write the
calibration register, we can always provice measurements with the right
units. It is also wrong to provide sensor readings that do not match
with the units specified by the channel. After this change voltage is
always reported in V, current in A and power in W.
Note that power measurement had the current LSB hardcoded in the
calculation (assuming 1mA/LSB), this has been fixed as well.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Following dtschema practices, add phyisical units to the shunt resistor
value: milliohms.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The "pmic" driver was in reality a driver for NXP PCA9420 PMIC. There's
no "universal PMIC". While the driver may work for other NXP PMICs, it
is clearly not generic for other vendors PMIC.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Force cache-size to 0 and treat flashdisk as read-only when backing
partition has read-only flag set. This allows users to save RAM when the
application does not write to the flashdisk, e.g. when a predefined FAT
filesystem is used.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Ensure that PECI block is enabled in the EC Subsystem by clearing
the PECI_DIS (peci disable) register
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Following the modification of the STM32 OSPI driver, the clock-names
binding is now required
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
The icmsg backend for ipc_service has a limitation of supporting only
on endpoint. This limitation is acceptable for many IPC instances.
However, some require to use multiple endpoints sharing a single
instance. To preserve the simple and the most efficient single-instance
backend, a separated backend is introduced implementing a wrapper
around icmsg core which adds multiple endpoints support.
There are two multi-endpoint ipc_service icmsg backends: one in the
initiator role, and the other one in the follower role. In a IPC
configuration one end of communication must be in the follower role
while the other one is in the initiator. The initiator initiates
an endpoint discovery handshake to establish enpoint identifiers for
requested endpoint names. The follower responds to requests sent by
the initiator.
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
For larger transfers DMA can be used enabling other tasks
to continue running. A threshold of 32 byte transfers
is about right and is defined threshold value for using DMA.
This does not currently support multiple SPI transactions changing
chip select with DMA (though the hardware supports this) currently.
Instead opting for the simpler first change of enabling one shot
DMA SPI transfers for those where the size warrants it.
Adds the loopback binding option to enable the spi_loopback test.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add support input interrupts for GPIO pins on NXP S32Z27
SoC. The driver will convert GPIO pin to respective
interrupt line that will be processed by External
Interrupt Controller.
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Add initial support for the NXP S32Z27 SIUL2 External
Interrupt Controller. Each SIUL2 node has a child node
will act as an interrupt-controller that processes external
interrupt signals.
This driver is required to manage GPIO interrupts.
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
New ADC driver for the TI CC13xx/CC26xx family.
ADC channel configurations are translated from Zephyr constants to
simplelink driverlib ones (e.g., sample times use a lookup table).
Async mode was also implemented & tested.
Signed-off-by: Stancu Florin <niflostancu@gmail.com>
Adds Atmel SAMC20 and SAMC21 soc. C series is based on Cortex-M0+.
C21 contains CAN interface.
The init routines are same for SAMC20 and SAMC21. They use one
clock OSC48M without configuration.
The code is inspirated from atmel_sam0/samd21.
Signed-off-by: Kamil Serwus <kserwus@gmail.com>
This commit adds an optional property to the nRF21540 Front-End Module
devicetree description that specifies supply voltage in mV. This
property can be used by the nRF21540 driver to compensate the value of
achieved gain for different supply voltage.
Signed-off-by: Artur Hadasz <artur.hadasz@nordicsemi.no>
Signed-off-by: Jędrzej Ciupis <jedrzej.ciupis@nordicsemi.no>
Add SparkFun Pro Micro header connector that is implemented by many
other controllers. This allows hardware with compatible headers to
define the related GPIOs and peripherals.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
The ESP32 series MCUs allow to set a timeout which triggers an error
if the SCL line is unchanged for the specified amount of time.
By default, the ESP-IDF HAL sets the timeout to an arbitrary value of
10 times the bus cycle.
This is not sufficient for chips like the TI bq76952, which pulls the
SCL line low (clock stretching) for several 100 µs.
The timeout should also not be dependent on the chosen bitrate, as it
is defined by the time a chip needs for internal calculation before it
can provide requested data or continue communication.
This commit adds a property to devicetree to allow configuration of
the scl timeout. This value is set via direct register access, as the
ESP-IDF HAL does not provide access to the enable bit and does not
give any information about the maximum size of the timeout (defined
in I2C clock cycles in the register).
Fixes#51351
Signed-off-by: Martin Jäger <martin@libre.solar>
Microchip MEC172x has a modified eSPI SAF hardware implementation.
Hardware changes include multiple clock dividers for each SPI
flash device and data transfer using QMSPI local DMA.
espi reset interrupt is made a higer priority in MEC172x devicetree
because espi reset event resets all espi hardware and we don't
to want to service any other espi interrupt blocks when espi reset
occurs.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add bindings to describe a block storage device based on flash map
partition.
Co-authored-by: Johann Fischer <johann.fischer@nordicsemi.no>
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Add devicetree binding for the PSA Crypto Random source.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
This commit adds missing binding file for the ite,it8xxx2-usbpd.
Without this file, the DT_HAS_*_ENABLED macro wasn't defined and
couldn't be used in the Kconfigs.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
A USB TypeC connector has many peripherals associated with
it and the DTS binding in this commit provides a way to group
peripherals and properties in a device tree.
This binding is used with the USB-C Subsytem.
This is based on Linux, documentation:
https://www.kernel.org/doc/Documentation/devicetree/bindings/connector/usb-connector.yaml
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Add pin control properties to the STM32 UCPD bindings file so that
the pins can be configured in the device tree.
Signed-off-by: Sam Hurst <sbh1187@gmail.com>
Executing code out of RAM on IT8xxx2 requires that the relevant
addresses be mapped onto the CPU's instruction memory bus, referred to
by ITE documentation as Instruction Local Memory (ILM). ILM mappings
configure blocks of RAM to be used for accesses to chosen addresses when
performing instruction fetch, instead of the memory that would normally
be accessed at that address.
ILM must be used for some chip features (particularly Flash
self-programming, to execute from RAM while writing to Flash), and has
historically been configured in the Flash driver. The RAM for that was
hard-coded as a single 4k block in the linker script. Configuring ILM
in the flash driver is confusing because it is used by other SoC code as
well, currently in code that cannot depend on the Flash being functional
or in hand-selected functions that seem performance-critical.
This change moves ILM configuration to a new driver and dynamically
allocates RAM to ILM in the linker script, allowing software use of the
entire 64k RAM depending on configuration. This makes ILM configuration
more discoverable and makes it much easier to correctly support the
CODE_DATA_RELOCATION feature on this SoC.
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
USB interface that may be used to send messages from a USB host to
the M4 processor in the S3B, and vice-versa.
Signed-off-by: Michal Sieron <msieron@antmicro.com>
Add support for regulator-boot-on to PMIC driver. Many PMIC devices will
be enabled at boot, so this property allows the regulator framework
to correctly track their state.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
As part of a previous refactor, this property was removed from the STM32
USART binding. The driver code to support this feature was not changed.
This commit simply adds the property back to the new base .yaml for
device trees which used it.
Tested on a proprietary board using the STM32U5 on USART1.
Signed-off-by: Peter Maxwell Warasila <madmaxwell@soundcomesout.com>
Migrates all Winsen sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all WE sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Vishay sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all TI sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ST sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Silabs sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Sensirion sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Semtech sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Seeed sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all SBS sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Plantower sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Panasonic sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all NXP sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Nuvoton sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Nordic sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Microchip sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Measurement Specialties sensors to inherit base sensor
device properties. This will allow us to define properties shared by
multiple sensors in one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Maxim sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all LM sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ITE sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Intersil sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Invensense sensors to inherit base sensor device
properties. This will allow us to define properties shared by multiple
sensors in one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Infineon sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all HOPERF sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Honeywell sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Espressif sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Bosch sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Avago sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Atmel sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Asahi-Kasei sensors to inherit base sensor device
properties. This will allow us to define properties shared by multiple
sensors in one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all Aosong sensors to inherit base sensor device properties.
This will allow us to define properties shared by multiple sensors in
one place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all AMS sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Migrates all ADI sensors to inherit base sensor device properties. This
will allow us to define properties shared by multiple sensors in one
place.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Introduces an initial set of devicetree properties to be inherited by
all sensor devices, similar to how we define a base set of devicetree
properties for I2C and SPI devices. These properties will be used by the
future sensor subsystem to manage and expose sensors to a host operating
system, through HID or another protocol. Additional properties may be
added in the future.
An earlier version of this patch attempted to use the label property
instead of friendly-name, as it was noted during code review as a
possibly legitimate usage of the mostly-deprecated label property.
However, in practice it was difficult to implement because most sensor
bindings also inherit from i2c-device.yaml or spi-device.yaml, and
therefore inherit the deprecated label property from base.yaml. To work
around the deprecation, every sensor binding would have needed to
explicitly block the label property with a property-blocklist, which
would somewhat defeat the purpose of having a shared sensor-device.yaml.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Add MEC172x full duplex qmspi driver version to support full
duplex transfers as expected by the Zephyr spi driver model.
On every spi clock we transmit one bit and receive one bit.
This driver will work with Zephyr SPI NOR driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
updated dts variables naming (hyphen instead of underscore).
moved all properties in microchip ldma yaml to a separate include file,
these properties will be common with the (to be added)
full duplex spi driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Newer ESP32 series MCUs like the ESP32-C3 contain some register changes
incompatible to the original ESP32 and the SJA1000.
The additions in this commit consider these changes and fix the
incompatibilities in the TWAI front-end for the SJA1000 driver.
Signed-off-by: Martin Jäger <martin@libre.solar>
Implement GPIO driver minimal API's for NXP S32 devices, based on SIUL2
peripheral. SIUL2 allows to control the pins electrical characteristics
such as internal pull resistors, pin direction and more.
GPIO driver API's for interrupts will be implemented in a future patch.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
This patch introduces support for NXP S32 LINFlexD peripheral operating
in UART mode. Polling and interrupt-based serial API's are supported.
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Introduce Pinctrl driver for SIUL2 module present on NXP S32 devices,
which provides control over all pins, such as function selection and
electrical characteristics that appear on external chip pins.
Signed-off-by: Manuel Arguelles <manuel.arguelles@nxp.com>
Add mode selection properties for regulator-pmic compatible. These
mode selection properties will be used with regulators that support
multiple modes, with each mode enabling specific voltage and current
limits.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Refactor binding to use root PMIC IC, so that properties can be shared
between regulator devices. Each individual regulator output is still
created as an individual device, since the regulator API aligns with
these devices better than the PMIC IC itself.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Convert timer driver to use a light weight syscon and DTS and convert
register information to use offsets and sys_read/sys_write instead of
structs.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Some windows might need to be set as writtable, so add a flag read-only
to DTS bindings which is set to true for all windows right now. This can
be set to false where needed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Instead of just declaring the memory window register in DTS and have
everything else all over the place (headers, Kconfig, etc.) this change
defines the memory window instances in DTS and uses the device model to
initialize the windows. Code is still part of the SoC, given that we do
not have a driver subsystem suitable for this type of device yet.
Move FW status to own workflow and separate from window setup.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If the flash is used in 4-byte addressing, reading SFDP will fail after
a system reset if the flash isn't power cycled or hardware reset, since
Zephyr will try to use 3-byte addressing while the flash (still) expects
4-byte addressing.
This commit adds the ability to send a reset command to the flash as part
of initialization, which complements the existing reset-gpio
functionality, and is useful on low-pincount flashes which do not have a
hardware reset.
Signed-off-by: Ole Morten Haaland <omh@icsys.no>
Added support for the AMS AS621x series of temperature sensors as a
variant of the TI TMP108 temperature sensor.
Signed-off-by: Jared Baumann <jared.baumann8@t-mobile.com>
Signed-off-by: James Johnson <james.johnson672@t-mobile.com>
Adding ethernet in the DTS file and corresponding binding
for Cyclone V SoC FPGA board..
Signed-off-by: Esteban Valverde <esteban.valverde.vega@intel.com>
Add a fifo address as int value into dmic yaml to separate different
outputs (corresponds to different dais) from the same hw block. Also
change shim address from array to int value.
Signed-off-by: Jaska Uimonen <jaska.uimonen@linux.intel.com>
Replace the hardcoded kPWM_Prescale_Divide_128
driver prescaler with the ones defined in the dtsi file
that allow overriding them by the user.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
This commit adds a driver to simulate GPIO state and interrupts
using the keyboard when using SDL.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Add 2 properties to configure the "any movement" event.
* Ability to disable the interrupt latch
* Select movement mode
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
Include files should not have compatible properties set. These do not
represent real hardware and should therefore not appear to do so, e.g.
by appearing in the bindings index as if they were a real hardware
peripheral.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 qmspi. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 adc. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 pwm. Update board dts, pinmux and driver files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Remove pinmux calls and add pinctrl support for mec15xx
and mec1501 espi. Update board dts, pinmux and espi driver
files.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
The FULLDRIVE description on the rt-iocon yaml file was
describing the slew rate and not the FULLDRIVE property.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
When the EXTI Line nb is not set as interrupt by default
(at reset value), the uart instance cannot waekup the
system from its low power stop mode.
The EXTI line must be specified, like with stm32WL55
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds a base binding for I3C controllers.
Note that this follows the Linux kernel 5.17 bindings under
Documentation/devicetree/bindings/i3c/i3c.yaml.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a few bits to the devicetree API tests for multi-bus
nodes where a bus can support multiple protocols. This uses
I3C as basis as I3C controller can support both I2C and I3C on
the same bus, while I2C controller cannot support both. So
this needs to make sure the correct bus macros are generated
if appropriate (and not generated if not needed).
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add support to at86rf212[b] sub-giga devices. This work enables use of
pages 0, 2 and 5 in accordance with IEEE-802.15.4/2003/2006/2011. The
proprietary speeds can be object of future work.
Note: It is recommended that user define a power table for better
performance, low emissions and to save power. A reference power table
can be found in the datasheet and should be used for tests only and
not on a final product.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The current version of power table is hardcoded in the driver which is a
problem when use devices in production. This change remove all hardcode
from driver and reimplement the feature to allow people create a table
which is defined in devicetree. The big advantage is that each board can
define their own table based on lab tests and allows use of FEM devices
inclusive.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The property is similar to the usb_controller_index_t
enum that is available in the NXP SDK.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
This commit introduces the 1-wire master driver for maxim ds2485.
The ds2485 master has nearly the same (1-wire) feature set and
i2c-interface as the ds2477.
Therefore the common parts are extracted, but to avoid
any nda troubles only the ds2485 specific part is included.
Compared to older 1-wire masters, the ds2485 supports higher level
commands, supporting multi byte operations, search next, automatic crc
calculation.
In this driver only basic read and write operations are supported,
further hardware features are not yet utilized by the driver.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This driver provides an interface to SocketCAN interfaces of the Linux
system running a Zephyr application with the native_posix board. These
interfaces may be virtual or actual CAN buses.
Signed-off-by: Martin Jäger <martin@libre.solar>
Migrate information to DTS and get it from there on the code. Note that
for CAVS 15, the information is not migrated as there's no DTS entry for
it. It can be brought back (in the DTS) if TLB support is enabled for
it.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Add emulator functionality to the serial_test driver, so that it can be
used to simulate a device on the other end of the uart.
If you don't set the buffer-size property in the dts node, there should
be effectively no change from the previous behavior.
Signed-off-by: Jeremy Bettis <jbettis@google.com>
Add the DMA in the DTS binding for OCTOSPI interface
for the stm32 devices from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
There are three types GD32 FMC.
GD32 FMC v1: its flash memory has 1 bank, page size is equal in the
bank, flash size is smaller than 512KB.
GD32 FMC v2: its flash memory has 2 banks. Page size equal within the
same bank but different between banks. Flash size can be up to 3072KB.
FMC v2 has two registers to control bank0 and bank1 separately.
GD32 FMC v3: its flash memory has 2 banks, use sector size as the
minimum operating unit, the sector size is not equal.
Signed-off-by: HaiLong Yang <hailong.yang@brainco.cn>
Define RaspberryPi Pico ADC.
The ADC has internally connected temperature sensor,
Add property to enable this.
The ADC has a single VREF. VCC usually connects to it,
but it may not be in a case.
Add property to make configurable it.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Use the clock control API to enable peripheral clocks. Note that both
GPIO and pinctrl drivers are updated at once since they share some IP
blocks.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Use the clock control API to turn on ADC clocks. Note that clock
selection is not yet implemented, so we still rely on custom rcu
properties for that.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This patch adds a clock control driver for GD32 platforms. It is
important to note that the driver is only able to handle peripheral
clocks, but not "system clocks" (e.g. PLL settings, SYS_CK, etc.). On
some similar platforms (STM32) this task is embedded in the same clock
driver, performed at init time but with no options to do any
manipulation at runtime via the API calls. The clock control API as-is
is really orthogonal to "system clocks", and it is arguably a bad idea
to embed system clock init code in a clock control driver. It can be
done at SoC level still using Devicetree as a source of hardware
description/initial configuration.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Remove the CAN_STM32FD_CLOCK_DIVISOR configuration option,
and add configuration via dts property clk-divider instead.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
Changes to code:
1. Renamed CAVS_IPC API from common/include/cavs_ipc.h to
common/include/intel_adsp_ipc.h. Renamed all API functions and structs -
added "intel_adsp_" prefix.
2. Moved definitions from intel-ipc-regs.h and ace-ipc-regs.g to SOC
specific headers include/<soc_name>/adsp_ipc_regs.h.
3. Added new common intel_adsp_ipc_devtree.h header with new
macros to retrieve IPC and IDC nodes and register addresses.
Put those new macros in code replacing hardcoded values outside of
devicetree.
4. Changed documentation of IDC and renamed IDC register struct
to have common name between all intel adsp socs.
5. Removed excessive docs description on cAVS IPC protocol.
Changes to Devicetree:
1. Renamed in all CAVS boards .dtsi files content in IPC nodes:
- "cavs_host_ipc" node labels to "adsp_ipc" labels.
- compatible "intel,cavs-host-ipc" renamed to
"intel,adsp-host-ipc".
2. Added (previously missing) yaml file for "intel,adsp-host-ipc"
compatible.
3. Renamed in all CAVS boards .dtsi files content in IDC nodes:
- "idc" node labels to "adsp_idc" labels.
- compatible "intel,cavs-idc" renamed to "intel-adsp-idc"
4. Renamed intel,cavs_idc.yaml file to intel,adsp_idc.yaml
so it is suitable for both CAVS and ACE SoC family.
Moved it from ipm bindings to ipc bindings where it belongs.
Changes to Kconfig:
1. Renamed existing Kconfig option CONFIG_CAVS_IPC to
INTEL_ADSP_IPC.
2. For renamed INTEL_ADSP_IPC addded default value based on
status of the "adsp-ipc" and "adsp-ipc" node.
Signed-off-by: Andrey Borisovich <andrey.borisovich@intel.com>
Convert the device to be Devicetree based. Adjusted tests and other
areas that were using old Kconfig properties.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some custom refresh profiles need to set the PLL and VDCS
registers. Add them as optional DT properties.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Add support for overriding display LUTs in the UC81xx driver. This
makes it possible to use different LUTs for the full and partial
refresh profiles.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Add a separate profile for partial refreshes. This makes it possible
to specify a separate refresh configuration for partial and full
refreshes.
The driver now transitions to full refresh mode when blanking is
turned on. It transitions back to partial refresh mode when there is a
write while blanking is off.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Introduce the concept of refresh profiles which are specified as a
child node in the device tree. This makes it possible to use different
overrides for different types of refreshes (full/partial).
The only profile that is currently supported is the "full" profile.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
This patch is to add Cadence QSPI NOR flash device tree element
for the Cadence QSPI NOR flash driver bringup
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
This adds flash driver for Renesas SmartBond(tm) family.
This technically uses QSPI controller but since default and most
commonly used configuration is to boot from external QSPI flash (DA1469x
do not have built-in flash) and that flash is mapped into memory space,
it can be represented as internal flash.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
This adds serial driver for Renesas SmartBond(tm) family. Both polling
and interrupt APIs are supported.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
This adds GPIO driver for Renesas SmartBond(tm) family.
Driver supports pin configuration (input/output) and interrupts on edge.
Interrupts on level are not supported by hardware.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Signed-off-by: Ben Lauret <ben.lauret.wm@renesas.com>
Add a new reset driver for GD32 platforms. This driver controls the
reset registers from the RCU peripheral. It can be used to restore
peripherals to their initial state when initializing a device.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
It was not possible to disconnect a pin using the nRF pinctrl driver.
That is, it was not possible to set PSEL to 0xFFFFFFFF (indicating pin
is not connected). This can be useful in certain scenarios, e.g. a
bootloader configures all signals of a certain peripheral but
application then needs to disconnect certain signals.
A new DT macro has been introduced to accomplish this:
NRF_PSEL_DISCONNECT. It can be used like this to explicitely disconnect
a peripheral signal:
```
&pinctrl {
uart0_default: uart0_default {
group1 {
psels = <NRF_PSEL(UART_TX, 0, 1)>,
<NRF_PSEL_DISCONNECTED(UART_RX)>;
};
};
};
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Despite being used in GD32 dts files, the compatible did not exist. Note
that there is no GD32 flash driver yet.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The TS_CAL values for the temperature sensor are measured on 12, 14 and
16 bit resolution depends on the STM32 series. Because the drivers
operates at 12 bit resolution the TS_CAL1 and TS_CAL2 must be divided.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
This commit defines a new dma version for devices like stm32U5.
The peripheral is a GPDMA in this soc serie.
It has several specific definitions used by its stm32 LL driver
compared to the V2, including up to 16 channels.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
There are 3 bindings for STM32 serial driver:
st,stm32-uart.yaml
st,stm32-usart.yaml
st,stm32-lpuart.yaml
Add a common st,stm32-uart-base.yaml that would be included by these
3 bindings an would group common properties.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
This commit adds string token versions of the values also
in items inside string-array.
Signed-off-by: Radosław Koppel <r.koppel@k-el.com>
Co-authored-by: Marti Bolivar <marti.bolivar@nordicsemi.no>
Co-authored-by: Kumar Gala <galak@kernel.org>
Add missing support for the triggered mode using GPIO
interrupt alert pin. It uses mode detection at runtime
which allows working multiple sensors with different
modes simultaneously.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
The new property nist-config is introduced to the stm32 mcus
to configure the RNG for NIST SP800-90B certification.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The gpio-leds binding is meant for LED drivers, not GPIO. As in Linux,
move the binding to the led folder.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
gpio-keys binding has been used in Zephyr to describe random push
buttons in boards. On Linux, it is used by a keyboard input driver,
while in Zephyr is, in most cases, used directly in applications out of
the device driver model. This should likely be _fixed_ if one day we
have a proper input device class. Still, we can align a few things:
- Inherit from base.yaml (we need status, compatible, etc defined there)
- Remove the requirement of a label in child nodes
- Fix child nodes label description
- Move to dts/bindings/input
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Don't import the label prop from base.yaml as it is marked deprecated.
This lets the various tests that still use DT_LABEL() to work properly.
Signed-off-by: Kumar Gala <galak@kernel.org>
Mark 'label' property as deprecated in base.yaml. 'label' is still
defined and valid for specific bindings to specify like gpio-keys.yaml
or fixed-partitions.yaml.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add spi0 and spi1 configuration to rp2040.
spi0 and spi1 are declared as compatible with
"raspberrypi,pico-spi" and "arm,pl022".
"raspberrypi,pico-spi" is just inherited from
"arm,pl022" and "reset-device"
spi0 and spi1 declare as compatible with "raspberrypi,pico-spi"
and "arm,pl022".
"raspberrypi,pico-spi" is just inheriting "arm,pl022" and
"reset-device" for declaring the 'reset' property,
with no additional property and implementation.
Add also pinctrl macros to dt-bindings header.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Add fundamental feature support for PL022 SPI peripheral.
This commit implements synchronous transfer with 8bit-MSB format.
Optional functions are not currently implemented yet.
- interrupt based transfer is not implemented yet.
- DMA transfer is not implemented yet.
- Slave mode is not implemented yet.
- Currently support only 8-bit data transfer.
Hardware limitation:
- LSB-first format is not supported by hardware.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
The binding 'nxp,lpc-iap' is no longer used, which is confirmed
by running:
$ find ${ZEPHYR_BASE}/dts/arm/nxp -type f | egrep -e '\.dts(i)*$' | \
xargs grep -nH nxp,lpc-iap
Changes in this commit:
- remove DT_HAS_NXP_LPC... in drivers/flash/Kconfig.mcux
- remove schema file for nxp,lpc-iap
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
The binding 'nxp,iap-lpc' is used for different flash controllers,
preventing clarity. This commit introduces bindings for each version of
the flash controller, as they appear with NXP lpc device families:
nxp,iap-fmc11: for the flash controler used on the lpc11u6x family
nxp,iap-fmc54: for the flash controler used on the lpc54xx family
nxp,iap-fmc55: for the flash controler used on the lpc55xx family,
except lpc553x
nxp,iap-fmc553: for the flash controler used on the lpc553x family
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
The SSD16xx driver currently hard-codes a couple of register overrides
that aren't relevant or even correct for many devices. Make them
optional device tree properties instead.
Note that this changes the behavior for panels that expect
SSD16XX_CMD_DUMMY_LINE and SSD16XX_CMD_GATE_LINE_WIDTH to be set by
the driver. This fixes a bug where the incorrect value
was written to all SSD16xx panels except for GDEH0213B1 and GDEH029A1.
The overlay files for devices that need dummy line and gate line width
to be specified have been updated as a part of this commit.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The OTP in most SSD16xx-based displays normally contain default
VCOM/GDV/SDV values. Make all of these optional in the device tree.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Add the option to specify the minimum duration that the `reset-gpios`
pin is held low on boot. This lets devices with additional capacitance
on the reset line still reboot the Bluetooth controller.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
This fixes underrun issues when hardware flow control can't be used.
Only tested on STM32F4.
Signed-off-by: John Kjellberg <kjellberg.john@gmail.com>
...
All the of the ITE it8xxx2 devicetree compatiables are of the form
ite,it8xxx2-<DEV>. However the PECI device was ite,peci-it8xxx2,
rename the compatiable to match the pattern used everywhere else.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add dts bindings for the NIOS2 QSPI controller and flash device and
add nodes to the dts files for these devices as well.
Signed-off-by: Kumar Gala <galak@kernel.org>
Fat finger mis-typed when I renamed the file last time.
So correctly name the file this time. Hopefully this is
correct and won't need anymore renaming... :(
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The current atmel sam flash driver was develop based on the cortex-m7
version of smart arm microcontroller. The driver support write
protection and cache functions which is not supported by other cortex-m
variants. This fixes current driver implementation and devicetree
entries for all sam variants.
Notes:
* The cortex-m3 doesn't have support erase pages flash command and
because of that the driver still not not compatible. Keep it disabled
until a patch be send. The hwinfo driver is not affected by this
restriction.
* The sam4l variation requires a specific driver because uses another
flash controller (flashcalw). Added another compatible to
differentiate and keeped node disabled until a driver be available.
Fixes#48516
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
() Fix the compatible string from "intel,dai,dmic" to
"intel,dai-dmic".
() Also rename the yaml file to have vendor name first.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use a test compatible so that test can create a DT-based device and
provide a valid choice when building the test.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In order to work on a clock speed higher than 20 MHz, IO MUX is required.
Co-authored-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Signed-off-by: XiNGRZ Chan <hi@xingrz.me>
various microchip bindings set 'girq-cells' and 'pcr-cells'
sections in the bindings. However the bindings where for the
client nodes and thus do not need to set these.
Signed-off-by: Kumar Gala <galak@kernel.org>
Change the wording about "alternate/optional" clock to "domain" clocks,
to better describe the feature and minimize confusion.
Additionally, provide more description about domain clocks and dual
domain functionality implemented in peripherals.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Adds optional device tree property to specify a default character
to clock out when the TX buffer pointer is NULL. If the property is
not set the existing behavior (default char of 0x00) is used.
I verified the expected behavior using an i.MX RT685 board and
logic analyzer that the def-char character is transmitted when
TX buffer pointer is NULL.
Signed-off-by: Bryce Wilkins <bryce.wilkins@gmail.com>
LPC55s3x family has an additional analog mode bit available. Update
IOCON binding and IOCON driver to support setting this bit via a pin
control property.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Use Devicetree to describe the UART UPIPE IEEE 802.15.4 driver. This
allows to remove usage of IEEE802154_UPIPE_DRV_NAME in preparation for
the removal of NET_CONFIG_IEEE802154_DEV_NAME.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_NRF5_DRV_NAME in preparation for the
removal of NET_CONFIG_IEEE802154_DEV_NAME.
All SoC files have been updated with the addition of an ieee802154 node
(disabled and only on those SoCs that define ieee802154-supported. The
peripheral has been enabled in the nRF52840DK board (used for testing
ieee802154).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_KW41Z_DRV_NAME in preparation for the removal
of NET_CONFIG_IEEE802154_DEV_NAME.
KW41Z files have been updated with the addition of radio and an
ieee802154 nodes The peripheral has been enabled in the frdm_k41z board
(used for testing ieee802154).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_CC13XX_CC26XX_SUBG_DRV_NAME in preparation
for the removal of NET_CONFIG_IEEE802154_DEV_NAME.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the radio and IEEE 802.15.4. This allows to
remove usage of IEEE802154_CC13XX_CC26XX_DRV_NAME in preparation for the
removal of NET_CONFIG_IEEE802154_DEV_NAME. All boards used in testing
have been updated to enable the peripheral in DT as well.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
ICI (Inter-Core Interrupt Unit) interrupts and priorities were hardcoded
in C files. This patch moves this information to Devicetree and updates
code to make use of it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
sysconf base address was hardcoded in <soc.h>. Create a new compatible
and define it in Devicetree, where hardware needs to be described.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Introduce a simple binding for atmel,24mac402 EEPROM that the SAM
GMAC ethernet driver can utilize to get MAC address out of. We
introduce a 'mac-eeprom' phandle into GMAC ethernet devicetree
node that will provide a pointer to the MAC eeprom to utilize.
Signed-off-by: Kumar Gala <galak@kernel.org>
The CLINT (Core Local Interruptor) description was not aligned with
Linux. For example, there's no "riscv,clint0", but "sifive,clint0". The
peripheral is not described as an interrupt-controller either.
Ref. https://elixir.bootlin.com/linux/v5.18.14/source/arch/riscv/boot/
dts/starfive/jh7100.dtsi#L106
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
After some analysis I found out that there's no machine timer provided
by the "riscv" vendor. There are some specs for the mtime/mtimecmp
registers (this is why we can have a single driver), but the actual
register layout or implementations differ amongst vendors. GD32 uses the
Nuclei implementation, named "system timer" in their documentation. This
patch aligns with vendor specs.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This adds a driver for Maxims DS2484 Single-Channel 1-Wire master
driver. The DS2484 features an extra pin to enable sleep modes which
is available if the pin is configured in the device tree.
Signed-off-by: Caspar Friedrich <c.s.w.friedrich@gmail.com>
Unlike stated in 57df225b396e43358aac4cc998ed2e99fdb57780, RM0456.pdf
reference manual mentions about PLL1R that "Only division by 1 and even
division factors are allowed."
Though, in reference manual, there is one issue on PLL1R values
description, which should actually be:
0000000: pll1_r_ck = vco1_ck
0000001: pll1_r_ck = vco1_ck / 2 (default after reset)
0000010: Not allowed
0000011: pll1_r_ck = vco1_ck / 4
...
This description will be fixed.
Reflect this in binding and driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Instead of enabling WOVCRO clock based on the SOC, use a configuration
to indicate support, so that each platform can specify if WOVCRO is
supported or not.
Signed-off-by: Ederson de Souza <ederson.desouza@intel.com>
Add binding for Aspeed AST10x0 clock driver. The clocks can be turned
on or off through the syscon registers.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
The UC8176 and UC8179 chips that exist in tree have subtly different
register layouts. Use separate compatible strings for these chips and
a quirks structure that describe device-specific behavior.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The GD7965 driver is really just a vendor name for the UltraChip
UC8179. Rename the driver to UC81xx since there are other chips in the
family (e.g., the UC8176) with an almost identical register interface.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
For the !SOC_I2C_SUPPORT_HW_CLR_BUS in which we implement bus
reset via GPIOs, change the devicetree properties to be actual
gpio properties and update the code to reflect this.
Signed-off-by: Kumar Gala <galak@kernel.org>
This commit adds the pll2 and pll3 clock control nodes
with st,stm32u5-pll-clock compatible.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit changes the range for stm32u5 pll divider values
to allow divider value of 1.
- DIVQ is allowed to beconfigured 1 for all PLL instances
- DIVR can be 1 for PLL2 and PLL3, but is not valid for PLl1.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
We have drivers for "nxp,lpc-rtc" and "zephyr,native-posix-counter"
devicetree compatibles, however we had no bindings for them. Add
simple bindings
Signed-off-by: Kumar Gala <galak@kernel.org>
Two files ending with yml while the rest is ending with yaml, just
rename those two to avoid special handling.
Fixes documentation build.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This CL adds a DT node, 'power_leakage_io', which property,
'leak-gpios', contains GPIOs that have leakage current. In oerder to get
better power consumption, npcx power driver will disable the connections
between these io pads and input buffers before entering deep sleep.
Then, restore the connections after ec wakes up.
The users can overwrite this property at board DT file. Here is an
example:
&power_leakage_io {
leak-gpios = <&gpio0 0 0
&gpiob 1 0>;
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL configures low-voltage (1.8V) detection via GPIO driver with
GPIO_VOLTAGE_1P8 flag. It also adds support for this flag in
pin_get_config() function.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Cleanup npcx low-voltage (1.8V) detection configuration. It removes
unused soc utilities, macros, and DT node. We will configure this
feature by GPIO driver with GPIO_VOLTAGE_1P8 flag later.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Move the RX (MISO) delaying capability information to Devicetree. It is
done using 2 properties:
- rx-delay-supported: enabled on SPI nodes that support delaying RX.
This property can be used by the driver to determine if this
capability is supported or not on a given instance.
- rx-delay: the actual RX delay value
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Specify the overrun character in Devicetree. Since 0xFF is the most
common value, DT property contains such default.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Devicetree is the natural place to describe hardware, so move the
maximum frequency the SPI can work with to Devicetree instead of relying
on values from HAL.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Some panels using this driver don't provide tcon/cdi/pwr/softstart
values in their reference code. It is normally expected that the right
values will be loaded from OTP in such cases. Make these values
optional to support such panels.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add configuration for SPI connected ADXL345 accelarator sensor
as adi,adxl345-spi.yaml.
Rename original adi,adxl345.yaml that configured for I2C
rename to adi,adxl345-i2c.yaml.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Implement support for SAML21 parts, tested on a SAML21 Xplained Pro dev
board. Confirmed operational peripherals: UART, GPIO, PWM, ADC.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Remove 'label' property from SDHC nodes. We can use variants of
DEVICE_DT_GET to get access to a device pointer for use in an
application.
Signed-off-by: Kumar Gala <galak@kernel.org>
The 'nxp,imx-flexspi-device' compatible that was specified in
the YAML file is not an actual compatible that is intented to be
used. Instead the YAML file is included in other YAML files
that set specific compatible.
If the 'nxp,imx-flexspi-device' was used we'd actually get an error
from edtlib because of having the same compatible specified by
two different YAML files.
Signed-off-by: Kumar Gala <galak@kernel.org>
All in tree device drivers use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Clean up unused psl functions in scfg.c, unused DT macros, unused psl DT
nodes and related yaml files. Currently, PSL pad configurations are made
by pinctrl mechanism. Please refer
https://issuetracker.google.com/234861079 for more detail.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
HDA is a common IP used across the entire ADSP line and deserves
a name respecting that alongside similiar IP drivers such as the
ADSP GPDMA driver.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add adsp-imr binding. This memory type is being used in intel adsp dts
but this binding was missing.
Co-authored-by: Marcin Szkudlinski <marcin.szkudlinski@intel.com>
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
All in tree device drivers on a bus use some form of DEVICE_DT_GET
so we no longer need to require label properties.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add simple clock control node in devicetree for beetle to handle
relationship between drivers (uart, timers, gpio) and clock controller
device.
Signed-off-by: Kumar Gala <galak@kernel.org>
Use DT_INST_FOREACH_STATUS_OKAY to reduce duplicated code for each
instance.
We make interrupts optional since they aren't always available.
Signed-off-by: Kumar Gala <galak@kernel.org>
Replace sensor_label property in devicetree with just a sensor phandle
property. This is more generic and allows driver to use DEVICE_DT_GET
instead of device_get_binding.
Signed-off-by: Kumar Gala <galak@kernel.org>
- adds properties 'group', 'index' and 'prescaler'.
- updates board's dts to include those properties.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Clean up unused pinmux function 'npcx_pinctrl_mux_configure()' and
related 'NPCX_DT_IO_ALT*' macro functions.
Please refer https://issuetracker.google.com/234861079 for more detail.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Switch from using a driver-specific, compile-time devicetree one-shot
property to supporting the newly added CAN_MODE_ONE_SHOT flag for
enabling/disabling one-shot mode at run-time.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove the support for enabling passthrough mode support for MPU9150
on the AK8975. We don't have a proper MPU9150 driver and the MPU9150
has been EOL. So its highly unlikely this code is being used.
Additonally we remove the device tree binding for the MPU9150 since
we don't have a proper driver for it.
Signed-off-by: Kumar Gala <galak@kernel.org>
CONFIG_SIFIVE_SPI_0_ROM (default y) was an option to disable spi0 if
used to access SPI Flash ROM. However, its design had a problem: it
relied on instance numbers. You had to set status okay for spi0 to make
it work (incongruent with the purpose of the option itself). This patch
makes things simpler: if such SPI0 is not available, simply keep it
disabled in DT. Bindings have been updated to mention this case.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
cAVS and ACE gpdma driver have several similarities. This commit merge
this two drivers into a single one for Intel ADSP devices.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add NPCX Power Switch Logic (PSL) DT node which controls the power rails
of SoC to get better power consumption.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL introduces how to configure PSL (Power Switch Logic) pads
properties such as input detection mode/polarity, pin-muxing and so
on via pinctrl mechanism. It includes:
1. Add two pinctrl properties and their enums for PSL input
detection configuration.
psl-in-mode:
- "level"
- "mode"
psl-in-pole:
- "low-falling"
- "high-rising"
2. Add macro functions to get PSL input detection and pin-muxing
configurations from 'pinmux', 'psl-offset' abd 'psl-polarity'
properties.
Here is an example to configure PSL_IN2 as the PSL detection input and
its mode and polarity.
/* A falling edge detection type for PSL_IN2 */
&psl_in2_gp00 {
psl-in-mode = "edge";
psl-in-pol = "low-falling";
};
A device will be introduced later which uses this pinctrl node to
configure PSL input detection settings and how to turn off VCC1 power
rail by PSL_OUT.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This peripheral combines a hardware-based USB CDC ACM serial interface
and a JTAG interface.
It is present in the ESP32-C3.
Signed-off-by: Martin Jäger <martin@libre.solar>
This will add ace compatible DMA driver.
Co-authored-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This adds basic support for the watchdog timer on the RP2040 MCU and
Raspberry Pi Pico development board
Signed-off-by: Jamie McCrae <spam@helper3000.net>
This commit adds support for the ds18b20 1-wire temperature sensor.
The sampling resolution of the sensor can be set in DT.
In case only a single device is on the bus, the driver issues
skip_rom commands. However, in case DT defines several devices,
the driver will use match_rom commands and therefore it is necessary
to set the rom_id of the device via the sensor attribute interface before
being able to sample sensor values.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The zephyr-serial w1 driver introduced in this commit implements
all routines for the w1 api on top of the zephyr serial driver.
W1 bit read, write, and reset operations are executed by issuing
polling zephyr serial byte read and write operations.
The driver should be usable on most platforms in zephyr that have
implemented support for the polling procedures of the serial driver.
As not all serial drivers are implemented exactly the same minor
additional quirks may be needed on some platforms.
The most notable difference of polling serial driver implementations
seems to be that some return immediately from poll_out after the
transmission was started(e.g. STM32) and others wait until
the transmission was completed before returning from poll_out
(e.g. NRF). While this has influence on the timeout, both types
are supported by this driver because the driver waits for a
configurable time period until it terminates the read.
The driver needs an appropriate open drain interface to be able
to communicate with slaves.
In the simpliest case this might be achived by configuring the mcu pins
in open-drain configuration with a (sufficiently small) pull-up to 3V3/5V.
Otherwise an external circuit needs to provide this interface.
Overdrive and Standard Speed modes are supported by this driver.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
This commit introduces a new api for the Dallas 1-wire protocol.
The api includes link functions for read and write operations on
bit, byte, and block level, as well as functions to reset and
lock the bus.
The bus configuration is derived from the device tree and can be
queried using w1_slave_count routine.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The default S0S1 drive setting is not suitable for TWI/TWIM pins.
Override it with S0D1 as for some SoCs (e.g. nRF52833) without
this the peripheral will not work properly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
There is no driver or other references to the zephyr,ipm-console
devicetree compatiable. So remove the binding.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add binding for zephyr sdmmc disk device, which uses the SD
subsystem to manage an SD memory card.
Fixes#46410Fixes#46266
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add a stm32h7 spi compatible.
This compatible intends to match all SPI hardware blocks that
can be compatible with the one available in stm32h7 devices,
for instance, but not limited to stm32u5 and stm32mp1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use consistent name for SPI HW block property so applications
using a device tree overlay work transparently.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Add MKR header connector that is implemented by Arduino MKR series.
This allows hardware with compatible headers to define the related GPIOs.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Some EFR32 SoCs use a secure element subsystem to manage
security features (i.e., TRNG, secure bootloader or cryptographic
functions).
This driver relies on the SE Manager high-level API provided by Silicon
Labs. The API interacts with the SE subsystem, provides helper functions
to achieve cryptographic operations and ensures that only one operation
is running at a time by using mutexes and semaphores.
Instead of relying on the SE Manager from Silicon Labs, one could
recreate the behaviour of the Manager and put the code in the crypto
driver folder and create a dependency for other drivers using the crypto
manager (e.g., keys, entropy).
I went for the SE Manager API as it is already there and supported by
Silicon Labs.
Tested using the random subsystem.
Signed-off-by: Steven Lemaire <steven.lemaire@zii.aero>
Add the stm32g0 bindings for the HSISYS to be used with the hsi divisor
with a factor programmable from 1 to 128.
Signed-off-by: TLIG Dhaou <dhaou.tlig-ext@st.com>
According to the formulas found in the reference manuals of the SoC
families using the "st,stm32-temp-cal" version of the temperature sensor
(i.e. G0, G4, H7, L0, L1, L4, L5, U5, WB, WL), the temperature is
computed with the following formula:
T = ((TS_CAL2_TEMP - TS_CAL1_TEMP) / (TS_CAL2 - TS_CAL1))
* (TS_DATA - TS_CAL1) + TS_CAL1_TEMP
What is called ts-cal-offset in the stm32_temp driver is therefore the
same value as TS_CAL1_TEMP1. Use it directly instead of defining another
property.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The stm32_temp driver defines the ts-voltage-mv property to determine
the reference voltage of the ADC in the temperature computation. However
this information is already available in the device tree at the ADC
level (even with the same default value). Use it through the ADC API
instead of duplicating the information.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This new DTS Node is defining a ratio for Vbat internal
bridge of monitoring sensor connected
to a ADC internal channel. The voltage reference value
is given by the ADC of the stm32.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Like other temperature or vrefint sensor, the stm32 mcu
also have a Vbat monitoring internal channels on ADC.
Add this entry to the device tree.
The vref is usually 3300mV present on the target board.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
-pin properties, e.g. tx-pin have been replaced by pinctrl. Mark them as
deprecated since old pin configuration schemes will be deprecated in
Zephyr 3.2.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit moves the hardware configuration for ledc
peripheral to the device-tree instead of Kconfig.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Enable pin control support for SWO log backend, by creating a new
ITM node for the ARM instrumentation trace macrocell. Add pin control
properties under this node, and refactor the swo-req-freq property to be
defined within this node.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit rewrite renesas R-Car clock driver in order
to be able to support any new SoC easier.
This work is so creating a clock driver per soc alongside a
common driver for all reneasas r-car boars.
- drivers: create a driver per soc
- create a common driver
- create a common header used by soc & common driver
- create a soc specific driver calling for common driver
- dts: use new compatible
- use old yaml as common yaml
- create a new "child" yaml to define the new compatible field
- change compatible in device tree
As in Linux, the driver can support both r8a77951 and r8a77950
SoC's so we decided to name the new driver as in Linux with Zephyr
prefix : "clock_control_r8a7795_cpg_mssr.c".
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Panasonic's reduced Arduino header is based on the Arduino UNO layout.
The main difference is that some pins are not available due to the
lack of pins on the Panasonic module.
Signed-off-by: Steffen Jahnke <steffen.jahnke@eu.panasonic.com>
Bindings for Intel HDA now require the buffer alignment property to be
set.
Sets the property to 128 bytes for the common Intel cAVS device tree as
was implied by the tests cases.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Enable statically allocated buffers to determine their buffer alignment
with a device tree property rather than having to find out through docs.
Should save people lots of time.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Add I2C bus recovery support to the NXP MCUX LPI2C driver. Since the LPI2C
peripheral block does not natively support I2C bus recovery, recovery is
performed using GPIO bitbanging.
Fixes: #42574
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The armv8 timer, arm gic, and arm gic-v3-its don't use or need the
devicetree label property. Update the dts bindings to not require it and
remove setting of the label property in dts files.
Signed-off-by: Kumar Gala <galak@kernel.org>
In 8f9290d2741844 ('dts: bindings: riscv: Add and use bindings for
sifive CPUs'), new compat strings for SiFive CPUs were added, but with
riscv prefixes. Vendor-specific compats should just be prefixed with the
vendor, so move that over here.
Fixes: 8f9290d2741844 ('dts: bindings: riscv: Add and use bindings
for sifive CPUs')
Signed-off-by: Olof Johansson <olof@lixom.net>
G4 and U5 series missed clock information in DT. Driver likely worked
because it was using HAL helpers, bypassing the purpose of DT and clock
control drivers. The clocks property is now required in the binding
file.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Adds `four-byte-opcodes` property. When set, then used write and read
opcodes will be converted to 4-Byte opcode.
Doesn't convert erase opcodes yet.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Adds write opcode (`writeoc`) property. That allows to provide
custom write opcode in the DTS.
Doesn't support OPI mode.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
The driver supported getting register shift from Devicetree, from a
custom definition in SoC headers (fragile) or, it took a default value.
This change simplifies things by making reg-shift property required in
all instances.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The reserved memory mechanism (sections and regions definition) has been
entirely replaced, greatly extended and made it better by the work done
on the zephyr,memory-region compatible.
Since there is are no actual users, we can remove it.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This reverts commit 7f51907fda.
The problem with setting the priority at the highest priority possible
is that when the IPC is under high traffic, the WQ could starve the
scheduler.
Move back to a more sane preemptive priority as default value.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This includes DTS bindings for the Texas Instruments CC13xx/CC26xx flash
controller driver and adds support for it in CC1352R and CC2652R SoCs
DTS files.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Recently OpenAMP introduced the possibility to set the sizes for TX and
RX buffers per created instance. Expose this also to Zephyr users by
using a DT property "zephyr,buffer-size".
For the sake of simplicity use the same DT property to set the buffer
size for both TX and RX buffers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Extends #43119 with PPB and IO values of
`memory-region-mpu`.
That allows MPU region definition with
PPB or IO attributes in the DTS.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
This patch adds DTS properties for using wake-up mode
and the autosleep function to the ADXL362 driver.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
Add a pseudo device diver with device tree bindings for coredump.
The device tree bindings exposes memory address/size values to be
included in any dump. And the driver exposes an API to add/remove
dump memory regions at runtime.
Signed-off-by: Mark Holden <mholden@fb.com>
This commit aligns SPIM shim to utilize memory-region property from
nordic,nrf-uarte compatible. The memory-region is not required
property that enables user to specify placement of dma buffers
in memory region. It is done by assigning to memory-region property,
phandle to node with zephyr,memory-region and mimo-sram compatible.
When memory-region property is not specified for given
instance, buffer is placed in default RAM region with other data.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
This commit aligns UARTE shim to utilize memory-region property from
nordic,nrf-uarte compatible. The memory-region is not required
property that enables user to specify placement of dma buffers
in memory region. It is done by assigning to memory-region property,
phandle to node with zephyr,memory-region and mimo-sram compatible.
When memory-region property is not specified for given
instance, buffer is placed in default RAM region with other data.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Since the introduction of the `zephyr,memory-region` compatible
to create new memory region, drivers can now use the newly defined
region in the DT by using the macro LINKER_DT_NODE_REGION_NAME()
on the node_id to retrieve the region name and possibly allocated data
or variables in that region (or for whatever other use).
This is assuming though that the driver knows in advance the node_id to
reference.
A better approach is to add a new generic 'memory-region' property
that can be used by any driver to reference a region by using a phandle,
so that the driver can use that to retrieve the memory-region of interest.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The ALH is an intermediary device, which acts as a hub and provides an
abstracted support for numerous sound interfaces (e.g. SoundWire).
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
This sensor is virtually identical to the lsm6dso. The only difference
is the accelerometer ranges are double those of the lsm6dso.
Use the same driver. The difference is detected by using "st,lsm6dso32"
as the first compatible entry, followed by "st,lsm6dso".
An bit flag in the existing accel_range config field is used to check if
the chip is the doubled range or not.
Signed-off-by: Trent Piepho <trent.piepho@igorinstitute.com>
Config pwm open-drain mode without enabling STORE_REG. This CL
collects all active PWM's base address and related index in an
array. Then, pinctrl driver configs its open-drain mode by
finding the corresponding 'channel' index.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Pinmux is depricated (see #39740) and shouldn't be used anymore
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Extend the common ADC controller binding with a child binding that
allows specifying configuration of ADC channels.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add 'inversion-on' property to st7735r.
Issue INVON(21h) command on initializing if inversion-on was enabled.
As a result of this command, the display color is inverted.
Otherwise, INVOFF(20h) will be issued.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Add pin control support for IOMUXC peripheral present
on mimx8ml8_m7 soc. This reuses the existing pin
control driver for the IOMUXC peripheral, but uses a
new header and compatible binding to handle the
different register layout on this SOC.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add pin control support for IOMUXC peripheral present
on mimx8mq6_m4 soc. This reuses the existing pin
control driver for the IOMUXC peripheral, but uses a
new header and compatible binding to handle the
different register layout on this SOC.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add pin control support for mcimx7_m4 SOC. This reuses the existing pin
control driver for the IOMUXC peripheral, but uses a new header and
compatible binding to handle the different register layout on this SOC.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add the DTS binding for OCTOSPI interface for the stm32 devices
from STMicroelectronics.
This corresponds to a NOR octo SPI flash.
In this config, there is only on NOR-flash device.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx eSPI and host_subs driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx adc driver. Please notice users need to
configure the corresponding pinctrl nodes in 'pinctrl-0' property in the
adc0 DT node. For example, if ADC0 and ADC2 channels are selected for
the application, please add the follwoings in your board DT layout file.
&adc0 {
status = "okay";
/* Use adc0 channel 0 and 2 for 'adc_api' driver tests */
pinctrl-0 = <&adc0_chan0_gp45
&adc0_chan2_gp43>;
pinctrl-names = "default";
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in npcx tachometer driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in ps2 driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in pwm driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in i2c driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Replace soc-specific pin functions with Zephyr pinctrl api functions for
pin-mux configuration in uart driver.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL is the initial version for npcx pinctrl driver and introduces
pinctrl nodes for both IO-pads and peripheral devices for each npcx
series. Users can set pin configuration via these nodes in the board
layout DT file. It also wraps all configurations related to pin-muxing
in pinctrl_soc.h. Regarding the other pin properties, we will implement
them later.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
The drive-mode property is nRF specific, so prefix it with `nordic,`,
same as the `nordic,invert` property.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Enable pin control for lpc11u6x i2c driver, and remove pinmux usage from
board level DTS files.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
convert lpc11u6x syscon clock driver to pin control, and remove all
pinmux usage from driver and syscon dts node.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Update pin control driver for lpc11u6x. This SOC does not have a HAL,
so fsl_clock is not available. It also lacks a slew-rate field in the
IOCON register, so this property must be optional.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
switch gpio driver to use pio nodes to configure pin control settings,
and stop using pinmux driver within gpio driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Since implementation of clock source selection in consumer device drivers
could be achieved without usage of a clock-names property and no
example of usage is provided up to now, remove this property from existing
examples.
Additionally, make it clear in stm32 clock control binding that it is
driver's responsibility to correctly access clock source information
and use it as required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add STM32 clock mux binding.
Only property of a node using such compatible is to
select a clock input.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the UPLLCK clock for the CAN controller as recommended by the Atmel SAM
E70 data sheet.
Move the configuration of the clock prescaler from Kconfig to devicetree
and limit it to the values recommended by the SAM E70 datasheet.
Fixes: #45012
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add DTS binding for Motorola MC146818 compatible Real Time Clock.
This is being used for the RTC/CMOS timer on x86 PC-compatible
platforms.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add optional PINCTRL support to the Microchip XEC PS2 driver
shared between MEC15xx and MEC172x families.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Comparator will monitor signal though ADC channel, based on
user configuration, callback will be triggered.
This will enable comparator functionality for nuvoton MCU utilizing its
ADC threshold detection feature. Implementation is exported through
sensor trigger API. Use of CONFIG_ADC_CMP_NPCX is required.
Signed-off-by: Bernardo Perez Priego <bernardo.perez.priego@intel.com>
remove existing SDMMC SPI driver, since it is replaced by the SPI mode
SD host controller driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
with the legacy USDHC driver fully removed from the tree, the
nxp,imx-usdhc binding can now be used for the new SD host controller
driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
all in tree SOCs with the USDHC peripheral have now been converted to
use the new SD host controller USDHC driver, so remove legacy NXP disk
USDHC driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add SDHC driver implementing spi mode support for SD cards. This driver
implements the standard SD host controller APIs, and sets the host
property "is_spi" to indicate to the SD subsystem the card will be
running in SPI mode.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add generic SDHC dts binding, as well as DTS binding for NXP USDHC.
Update iMX.RT DTS binding to use USDHC compatible
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Make the LSE driving capability configurable for the STM32 series.
Fixes#44737.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Fix the descriptions for the ST STM32 FDCAN devicetree bindings. These
are derivates of the Bosch M_CAN, but they target specific SoC
implementations.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rename the base Bosch M_CAN CAN-FD controller devicetree binding to
match the product name and the upstream Linux devicetree binding.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Fold the simple bosch,m-can devicetree binding into the front-end
devicetree bindings. The bosch,m-can compatible is not used in Zephyr.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
MCP4728 is a 12-bit, Quad Digital-to-Analog Converter with EEPROM Memory.
Controlled via I2C interface.
Signed-off-by: Marek Janus <marek.janus@grinn-global.com>
In 92d8329d5b a new DT property was introduced to set the WQ priority
of the instance. The fallback value when the property was not present
was arbitrarily set to <0 PRIO_PREEMPT>.
The problem is that this value is actually changing the behaviour for
the code that is not explicitly setting the DT property, breaking in
some cases the existing code.
Move the default value to <0 PRIO_COOP> to give the old code a
consistent behaviour before and after the 92d8329d5b commit.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This is a follow-up to commit 1a01ca2adf.
Since support for pinctrl has been added to the qdec_nrfx driver,
the related binding can no longer require the `a-pin` and `b-pin`
properties to be defined.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add DT option to configure the data ready interrupt mode.
Latched is the default; pulsed can be enabled through
the drdy-pulsed DT, if desired.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
Add FDS (Filtered Data Type Selection) + High-Pass reference mode support
(FDS in CTRL6, HP_REF_MODE in CTRL7)
Values are configurable through DT per instance.
Signed-off-by: Maxime Vincent <maxime@veemax.be>
The PWM period cell will soon be required by the pwm_dt_spec facilities,
this patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The binding has no corresponding driver and it is not referenced
anywhere, so drop it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The binding did not define the PWM cells. Only channel and period have
been added as they are the minimum required ones (flags are not supported).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PWM period cell will soon be required by the pwm_dt_spec facilities.
This patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PWM period cell will soon be required by the pwm_dt_spec facilities.
This patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The period cell will soon be required by the pwm_dt_spec facilities,
this patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The PWM period cell will soon be required by the pwm_dt_spec facilities,
this patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The period cell will soon be required by the pwm_dt_spec facilities,
this patch adds it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The period cell will soon be required by the pwm_dt_spec facilities,
this patch adds it. Note that flags have not been added as they are
optional and not supported anyway.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Introduce has-interrupt-mask-reg DTS property for nxp,pca95xx driver.
This additionnal property allow to specify that the gpio expander has an
interrupt mask register that must be configured by the driver.
This allow to use this driver with PCAL95xx.
This fixes issue #44834.
Signed-off-by: Xavier Chapron <xavier.chapron@stimio.fr>
NXP LPUART IP supports loopback mode, where TX is internally connected
to RX input. Allow setting loopback mode up via the "nxp,loopback" dts
property.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Align the board dts with the recent changes in the "nordic,nrf-sw-pwm"
binding (remove the no longer existing `channel-count` property) and
add a node representing the edge connector for convenient referring
to SoC pins connected to it.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
... to align with what is used in most other PWM bindings.
Update PWM nodes in SoC .dtsi files accordingly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Align with other PWM drivers and treat the `pwm` parameter (described
ambiguously as "PWM pin") of the `pwm_pin_set_cycles` function as a PWM
channel, not an SoC pin. This will also make the driver consistent with
the `pwm-cells` property definition in the "nordic,nrf-sw-pwm" binding
and with related `DT_PWMS_*` macros.
The change described above requires also providing a way to specify
SoC pins that are to be assigned to the PWM channels. Hence, the commit
introduces in the "nordic,nrf-sw-pwm" binding the `channel-gpios`
property that replaces the `channel-count` one.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Rework bindings documentation to clearly illustrate the role of ahb
(and cpu1) prescaler which defines the actual core clock frequency,
and not only a bus frequency.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use enum to describe the range of allowed MSI values.
This will help to detect configuration issues earlier.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On some parts, it could be required to use steps before applying
highest frequencies.
This was previously done as part of LL_PLL_ConfigSystemClock_FOO
utility functions which are no more used.
Use device tree to mention when this is required and implement it
in stm32_clock_control_init().
Additionally, fix the calls tp LL_RCC_SetAHBPrescaler, which require
use of ahb_prescaler helper.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The pinctrl support made usage of the 'peripheral'
property no longer required.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
those bindings are no more needed since pinmux was
deprecated in favor of pinctrl.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
After pinctrl's subsystem support, I2C pin properties are
no longer required for pin muxing, however, this information
is still valuable in an eventual FSM failure if the target
SoC has no harwared mechanisms to support bus recovery.
In this case, bus recovery uses pin information to restore
the I2C bus state.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Adds hda link in and out drivers. The link in and link
out channels of HDA have small differences
with the host channels. Updates the existing
cavs_hda drivers and code to account for these
differences.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
all the consumers of the obsolete pinmux driver is
updated to use pinctrl API, this commit removes
the pinmux driver and assosciated sections.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
This commit has the necessary changes to update the consumers
of pinmux driver(SPI, I2C, UART) and update the board specific
files to use the pinctrl interface.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
Add pinctrl driver for CC13XX/CC26XX family of SoCs
to facilitate transition from pinmux to pinctrl.
`IOCPortConfigureSet()` from TI hal driverlib used to
implement the generic pinctrl driver.
Signed-off-by: Vaishnav Achath <vaishnav@beagleboard.org>
LPTIMER has a different `countermode` meaning.
We shall exclude introduced property from lptim bindings.
Alternative property (e.g. `external-mode`) can be added
later on to support external counter mode.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
Introduces H7 FMC bindings with support for
memory remap or swap configuration.
The following values are supported:
* disabled - default mapping (reset state).
* sdram-sram - swaps the NOR/PSRAM and SDRAM banks.
* sdramb2 - remaps SDRAM bank 2.
Signed-off-by: Georgij Cernysiov <geo.cgv@gmail.com>
the icm42670 from Invensense/TDK is a 6-axis accelerometer with
gyroscope and temperature sensing capabilities.
this initial driver does not support the devices 2K FIFO or many of the
other advanced features. Instead, only basic features are implemented.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@escolifesciences.com>
Add the period cell to GD32 PWM compatible and update all boards
accordingly. A period of 20 ms (50 Hz) has been set for all PWM LEDs.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Rather than specify input clock for each peripheral individually, instead
specify the relevant clocks in DTS.
This will enable easier support for non-default coreclk on fe310 in a
follow-up CL.
Signed-off-by: Shawn Nematbakhsh <shawn@rivosinc.com>
