The driver for STM32's independent watchdog already exists and is
compatible with the stm32l1 SoC. Enable the independent watchdog
for the stm32l1 series for use with this driver.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
This checks if the DMA controller supports or not
the memory-to-memory transfers. For DMA Version1,
in the stm32f2xx, stm32f4xx, stm32f7xx series,
only DMA instance 2 is able to transfer mem-to-mem.
For other series, with DMA Version2, there is no such a limitation.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Currently, only the stm32h747 soc is supported in the h7 foler.
The h7 series comes with both single core and dual core products.
This change moves C-M4 core out of stm32h7.dtsi so that it can be
included by single core STM32H7 soc description.
Signed-off-by: Moonkwun Jung <mkainyh@gmail.com>
STM32L073 soc variant is a STM32L072 with LCD peripheral.
Reflect this in dts definition by including stm32l072.dtsi
in stm32l073.dtsi.
This also allows to fix an issue on stm32l073 gpioe which
declared wrong reg definition.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added dts additions for stm32 nucleo f767zi board, also added
and modified soc addtions for thet board.
Updated dts reference file name.
Updated yaml to take out adc for now.
Signed-off-by: Roland Ma <rolandma@yahoo.com>
This patchset enables USART3 on the 96Boards STM32 Mezzanine.
It is broken out to J10 Grove Connector.
Changes:
- Enabled USART3 in board dts.
- Updated board index.rst with uart pinouts.
- soc dtsi: enabled usart3.
Test: Tested USART3 as console at 115200 baud
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
This patch enables SPI4 on the 96Boards STM32 Sensors Mezzanine.
SPI4 has been broken out to a Grove Connector on the board.
Changes:
- Updated board dts to enable spi4
- Updated board Kconfig
- Updated board documentation
- Update board pinmux
- Updated stm32f4 pinmux header file
- Updated stm32f401 dtsi
- Updated stm32f4 defconfig to enable PORTE GPIO
- Added board to spi_loopback test
Test: spi_loopback test passed
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
This patch introduces the support of the Low Power Timer
for the STM32WBxx from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patch introduces the support of the Low Power Timer
for the STM32L4xx from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
dts pinctrl definitions were pushed in tree without the code
available to deal with it. They have been kept waiting for the
code, but this is taking much more time than initially thought.
So in current zephyr tree, for all STM32 boards, we have pinmux.c
file which is used to configure pins and these files that are
basically no-op. This situation is creating a lot of confusion
especially to new comers, and create useless maintenance effort.
Remove these files for now.
When zephyr will ready to use them, this commit could be reverted.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit moves DMA parameters previously hard coded in the driver
to the dts.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There is no APB2 bus on stm32f0 series.
What could be found as APB2 in CMSIS files is actually
second group of APB (A.K.A APB1_2).
Fix nodes that are using this wrong reference accorss the series.
Fixes#20310
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32L151XB-A SoC is almost similar to the STM32L151XB SoC except that
it has more RAM (32KiB). Hence add devicetree and Kconfig support.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
STM32L1 uses the same spi controller as STM32F1 so we can just set the
right addresses and enable them. We also need to add the fixup names and
to correctly include the header for ST LL HAL.
Signed-off-by: Karl Palsson <karlp@etactica.com>
The patch adds initial support for STM32F030X4 SoC.
STM32F0 Cube package advises to use 'stm32f030x6' code
for both STM32F030x4 and STM32F030x6 SoC variants.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Add soc and dts files to support for most of the common peripherals
in the STM32G4 series. Add specific support for the STM32G431RB.
Signed-off-by: Richard Osterloh <richard.osterloh@gmail.com>
The driver for STM32's independent watchdog already exists and is
compatible with the stm32wb SoC. Enable the independent watchdog
for the stm32wb series for use with this driver.
Signed-off-by: Robert Weber <robertweber95@gmail.com>
Update the ADC bindings to include #io-channel-cells and update the
related dts files to set #io-channel-cells.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
SPI3 clock info were missing and following macros were
not generated:
- DT_ST_STM32_SPI_FIFO_40003C00_CLOCK_BITS
- DT_ST_STM32_SPI_FIFO_40003C00_CLOCK_BUS
Signed-off-by: Armando Visconti <armando.visconti@st.com>
