Add soc and dts files to support for most of the common peripherals
in the STM32G4 series. Add specific support for the STM32G431RB.
Signed-off-by: Richard Osterloh <richard.osterloh@gmail.com>
Add KConfig board support to match board jumper settings
Failing to update bank selection will affect GPIOs tied to VTR3
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
This patch re-namespaces global variables and functions
that are used only within the arch/arm/ code to be
prefixed with z_arm_.
Some instances of CamelCase have been corrected.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This is part of the core kernel -> architecture interface and
has been renamed z_arch_kernel_init().
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
k_cpu_idle() and k_cpu_atomic_idle() were being directly
implemented by arch code.
Rename these implementations to z_arch_cpu_idle() and
z_arch_cpu_atomic_idle(), and call them from new inline
function definitions in kernel.h.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add a set of build time assertions that checks if the peripheral base
addresses defined in dts nodes match the values provided by nrfx/MDK.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Various C and Assembly modules
make function calls to z_sys_trace_*. These merely call
corresponding functions sys_trace_*. This commit
is to simplify these by making direct function calls
to the sys_trace_* functions from these modules.
Subsequently, the z_sys_trace_* functions are removed.
Signed-off-by: Mrinal Sen <msen@oticon.com>
Enable CMSDK GPIO driver on v2m_musca_b1 SoC/Board. Add LEDs that are
on the board and init the pinmux for those LEDs to work.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds support for Kinestis K22
Co-authored-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Co-authored-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Co-authored-by: Tom Burdick <thomas.burdick@gmail.com>
Signed-off-by: Tom Burdick <thomas.burdick@gmail.com>
We shall not include core kernel headers in soc.h
header of ARM SoCs. We should try to only include
the vendor headers and auto-generated board header
from DTS. This commit implements this policy for
the SoCs, whose builds have shown to fail due to
header inclusion cycles.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This file contains redundant definitions of a bunch of nRF IRQ numbers
(not all, however) that only generates confusion, as enumeration values
provided by MDK can be used instead.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This change is done so that there is no need to additionaly include
<nrfx.h> before <soc/nrfx_coredep.h> (what might be a bit surprising)
and so that <nrfx_config.h> doesn't need to be include separately for
nRF SoCs requiring a special mapping of peripheral accessing symbols.
This commit removes also no longer needed inclusions and updates
the hal_nordic module with required minor correction of nrfx_glue.h.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Header files of nrfx HALs are not supposed to be included directly
but only with their names prepended with the hal/ directory (so that
an inclusion of an nrfx HAL header clearly differs from an inclusion
of an nrfx driver header).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
A commit that organizes the soc.h header of NXP SoCs:
- removing redundant inclusions of sys/util.h
- removing inclusions of device.h and kernel_includes.h
- including the auto-generated DTS board header
- including the fsl_common.h header
- fixing minor style issues
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We, now, have multiple nRF52x SoCs with 2.4GHz
Radio with LE Coded PHY Capabilities. Therefore,
we would like to have a Kconfig option and select
it in the corresponding SoCs. This allows us to
simplify several #ifdef blocks in the nRF Bluetooth
Controller that would, otherwise, require listing
all nRF SoCS with LE Coded PHY support.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Enable CMSDK GPIO driver on v2m_musca SoC/Board. Add LEDs that are on
the board and init the pinmux for those LEDs to work.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A 16bits on/off based PWM, found on MEC1501.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add RTC timer driver for CC13X2/CC26X2, and use it instead of systick
as system clock. It is necessary to use this timer for power
management support, so that the system can exit from deep sleep upon
expiry of timeouts.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Include .gcc_except_table (sub-)sections in linker files to support C++
with exceptions enabled. If these sections are not mapped warnings will
be generated for orphaned sections at link time.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Make sure that all sub-sections of .gcc_except_table are mapped in
rodata else C++ builds with exceptions enabled will generate warnings
due to orphan sections.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
No users of this driver after dropping quark platforms.
COUNTER_0_NAME was only defined by the QMSI driver and was defined but
not used in DTS fixup files of ateml_sam0 SoCs. Removing those leftover
defines as well.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This driver was still using CONFIG_* values to determine its address,
IRQ, etc. Add a binding for an "intel,hpet" device and migrate this
driver to devicetree.
Fixes: #18657
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
* add pinmux driver. hsdk board has arduino, mikrobus and
pmod interfaces, which can be confiured for different function,
such as: gpio, spi, uart, iic.
* add introduction for arduino, mikrobus and pmod interfaces.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
RT SOCs have several memory areas (OCRAMs, DTCM, ITCM, SDRAM, FLASH...)
but only two are selected for FLASH (code) and RAM (data).
It would be good to let the linker be aware about other regions, which
could then be used by drivers or application to create dedicated
sections and relocate memory. For example if we have code in ITCM and
data in DTCM, we still need a dma-able region/section for e.g.
video/camera buffers.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Add qemu_x86_long board (with CONFIG_X86_LONGMODE=y) for testing.
This requires adding support to soc/ia32 for long mode (trivial),
and adding a quick 64- to 32-bit ELF conversion before invoking
QEMU, which apparently doesn't like 64-bit kernel files.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The previous linker script was barebones and non-standard. It is
replaced with a script conforms to the rest of the Zephyr arches,
utilizing include/linker headers and standard macros.
link-tool-gcc.h is updated to account for the "i386:x86-64" arch and
the generation of 64-bit ELF binaries.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This patch adds basic build infrastructure, definitions, a linker
script, etc. to use the Zephyr and 0.10.1 SDK to build a 64-bit
ELF binary suitable for use with GRUB to minimally bootstrap an
Apollo Lake (e.g., UpSquared) board. The resulting binary can hardly
be called a Zephyr kernel as it is lacking most of the glue logic,
but it is a starting point to flesh those out in the x86 tree.
The "kernel" builds with a few harmless warnings, both with GCC from
the Zephyr SDK and with ICC (which is currently being worked on in
a separate branch). These warnings are either related to pointer size
differences (since this is an LP64 build) and/or dummy functions
that will be replaced with working versions shortly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Update the -march flag passed to the compiler to reflect the
underlying microarchitecture is 'goldmont'.
Fixes: #17104
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
There are 2 other timers that could be selected, let's just take the
first 32bits one. This should be sufficient to verify the driver.
Enabling the timer in relevant board's dts file as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
