FIFO_DEPTH should be in the SoC's Kconfig as this is a
configuration of SPI master controller in SoC.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Adds dts fixups for lpuart instance 2, which will be used for the
arduino_serial connection on the mimxrt1020_evk board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Clean up a left over from GPIO driver factorization.
Definition of GPIO_REG_SIZE and GPIO_PORTS_BASE do not need anymore
to be spread accross SoCs.
Put these definitions directly in STM32 pinmux driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit introduces a new Kconfig symbol to signify
that a CPU implements the Nordic-specific security
attribution unit. The symbol is meant to be selected
by Nordic SoCs that implement the System Protection
Unit (SPU) peripheral.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds the nRF9160 fixup and the source files
for SOC and MPU boot configuration.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit introduces the Kconfig file structure for nrf9160
SoC in the Zephyr tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Support musca board as a variant, it is a Cortex-M33 based SoC.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Signed-off-by: Minos Galanakis <minos.galanakis@arm.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
SAMD2x series have available the Optional Vector Table Offset Register
(VTOR). If this option is not selected, SCB->VTOR is not configured
properly and the application hangs if it's located in an offset
different than 0.
Removed select CPU_CORTEX_M from SAMD20, as it's already selected by
select CPU_CORTEX_M0PLUS
Signed-off-by: Miguel A. Borrego <jimjim17@gmail.com>
This commit renames the CLOCK_CONTROL_NRF5 Kconfig symbol to
CLOCK_CONTROL_NRF. The change is required to aleviates confusion
when selecting the symbol in nRF9160 SOC definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In the wake of 9cbe468a470fe6a103557d4352d37604a632b2fe we need
to update the nomenclature of DT_FLASH_DEV_NAME macros.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This patch adds a x86_64 architecture and qemu_x86_64 board to Zephyr.
Only the basic architecture support needed to run 64 bit code is
added; no drivers are added, though a low-level console exists and is
wired to printk().
The support is built on top of a "X86 underkernel" layer, which can be
built in isolation as a unit test on a Linux host.
Limitations:
+ Right now the SDK lacks an x86_64 toolchain. The build will fall
back to a host toolchain if it finds no cross compiler defined,
which is tested to work on gcc 8.2.1 right now.
+ No x87/SSE/AVX usage is allowed. This is a stronger limitation than
other architectures where the instructions work from one thread even
if the context switch code doesn't support it. We are passing
-no-sse to prevent gcc from automatically generating SSE
instructions for non-floating-point purposes, which has the side
effect of changing the ABI. Future work to handle the FPU registers
will need to be combined with an "application" ABI distinct from the
kernel one (or just to require USERSPACE).
+ Paging is enabled (it has to be in long mode), but is a 1:1 mapping
of all memory. No MMU/USERSPACE support yet.
+ We are building with -mno-red-zone for stack size reasons, but this
is a valuable optimization. Enabling it requires automatic stack
switching, which requires a TSS, which means it has to happen after
MMU support.
+ The OS runs in 64 bit mode, but for compatibility reasons is
compiled to the 32 bit "X32" ABI. So while the full 64 bit
registers and instruction set are available, C pointers are 32 bits
long and Zephyr is constrained to run in the bottom 4G of memory.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The CIAA and QFAB variants of the nRF52832 were missing in Kconfig,
although present in Device Tree. Add the relevant Kconfig entries in
order to be able to select them.
Fixes#12417
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add support for the TRNG device contained in the i.MX RT SoCs. It uses
the existing MCUX driver, and mostly consists in adding the Kconfig and
DTS entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The original implementation of gpio functions access registers
directly. Using LL library can add a set of unifying access
functions for all series of stm32 for avoiding accessing low level
code, and improve readability.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
All series STM32 have mostly the same GPIO architecture
and can share the same code for GPIO manipulation.
Functions of the external interrupt line control are also the same.
This patch extracts common code from them and put them into the 'common'
folder.
Functions of control GPIO of these series scattered in
soc/arm/st_stm32/stm32xx/ folders contain these functions:
stm32_gpio_flags_to_conf(), stm32_gpio_configure(), stm32_gpio_set(),
stm32_gpio_get, stm32_gpio_enable_int().
This patch merges them into the gpio_stm32.c file.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
* i2c, spi, gpio are not tested, remove them now.
* fix the license issue in openocd.cfg
* fix the shell related setting
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The initial support of iotdk which is a board based on Synopsys
ARC IoT SoC.
In this commit, it includes
* processor support
* UART driver
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Adds support for the device configuration data (DCD), which provides a
sequence of commands to the imx rt boot ROM to initialize components
such as an SDRAM.
It is now possible to use the external SDRAM instead of the internal
DTCM on the mimxrt1020_evk, mimxrt1050_evk, and mimxrt1060_evk. Note,
however, that the default board configurations still link data into
internal DTCM, therefore you must use a device tree overlay to override
"zephyr,sram = &sdram0"
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moves the default TEXT_SECTION_OFFSET from the board level to the soc
level for the imx rt series. This offset is used to reserve space for
the imx boot header for external xip flash images.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds support for the boot data, image vector table, and FlexSPI NOR
config structures used by the imx rt boot ROM to boot an application
from an external xip flash device.
It is now possible to build and flash a bootable zephyr image to the
external xip flash on the mimxrt1020_evk, mimxrt1050_evk, and
mimxrt1060_evk boards via the 'ninja flash' build target and jlink
runner. Note, however, that the default board configurations still link
code into internal ITCM, therefore you must set CONFIG_CODE_HYPERFLASH=y
or CONFIG_CODE_QSPI=y explicitly to override the default. You must also
set CONFIG_NXP_IMX_RT_BOOT_HEADER=y to build the boot header into the
image.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This commit configures ETM/TPIU clock upon startup in case SWO logger
backend is enabled on Atmel SAM E70 SoC.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By default, after reset SWO signal is not connected to GPIO pin.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By default, after reset SWO signal is not connected to GPIO pin. This
commit adds required initialization code to enable support for SWO
logger. Not all SoC series support the feature.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit adds Serial Wire Output (SWO) logger backend. SWO is an
extension of Serial Wire Debug (SWD) port developed by ARM.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
On STM32L4, 14 pins (Port G[15:2]), require external power supply.
Activate this at port G init when PWR_CR2_IOSV is defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Zephyr gecko drivers depend on libraries provided by the vendor. The
same libraries may also be used directly by the application code or
RAIL library. To facilitate the latter use case scenario this commit
adds Kconfig options to independently enable compilation of vendor
HAL library modules.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
* Add DTS support for gpio controller driver
Signed-off-by: Ashokkumar B <ashokkumar@zilogic.com>
Signed-off-by: Subash G <subash@zilogic.com>
Signed-off-by: Vishnu K <vishnu@zilogic.com>
Signed-off-by: Vaishnavi D <vaishnavi.d@zilogic.com>
By adding 'aliases' node in SoC .dtsi file it is possible to generate
DT_ defines which specify a logical name rather than relay on module
location on APB bus. E.g. DT_SILABS_GECKO_USART_40010000_LABEL becomes
DT_SILABS_GECKO_USART_USART_0_LABEL. Thus it is possible to remove
dts_fixup.h defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Fixes an ethernet build error introduced with MCUXpresso SDK 2.5.0,
caused by a slight change in the ethernet pll configuration structure.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add uart5 nodes to stm32f1 series dts.
Provide matching dts_fixup add-on.
Signed-off-by: Chen Han <qq1433255094@outlook.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Updates the MCUXpresso SDK to version 2.5.0 for applicable SoCs.
Wireless (KW*) and legacy (KL25) SoCs were not included in this
MCUXpresso SDK release and are therefore not updated here.
New in this release is SoC-level and board-level support for external
xip flash in the i.MX RT family.
For RT1050, we are now using the MCUXpresso SDK for the EVKB version of
the board, which correponds to an upgrade from A0 to A1 silicon.
However, we don't yet have Kconfigs in place to support A1 silicon part
numbers, and therefore add a simple cmake hack to convert A0 part
numbers to A1 part numbers.
The SDK flash driver interface also changed slightly in this release,
and thus the zephyr flash shim driver is updated accordingly.
Origin: MCUXpresso SDK
License: BSD 3-Clause
URL: mcux.nxp.com
Purpose: Provide device header files and bare metal peripheral drivers
for Kinetis, LPC, and i.MX SoCs.
Maintained-by: External
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add support for Low Speed External 32.768 kHz oscillator (LSE ).
Add support for MSI PLL-Mode offering an automatic calibration feature
in combination with the LSE. This allows the MSI to reach an accurate
+/-0,25% clock perfectly suitable for USB full-speed clock.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
SPI devices almost always require chip selects, which are configured
through GPIOs. Make the GPIO infrastructure available by default when
SPI is enabled.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
In the wake of introducing nRF9160 .dtsi header, we are
adding several HAS_HW_NRF_xxxx Kconfig symbols, for the
peripherals present in nrf9160 SoC.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Make the following nRF peripheral drivers:
- ADC
- GPIO
- I2C
- SPI
- UART
- USB_DEVICE
enabled by default so that users do not need to explicitly enable them
in their applications after choosing an nRF SoC as the build target.
Kconfig options enabling these drivers depend on both a given hardware
feature (e.g. I2C) and an nRF family SoC selected, so effectively they
will be automatically enabled only when it is adequate (and in most
cases these drivers are the only option for a given hardware feature
on nRF SoCs).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Implementations of both flavors of serial drivers for Nordic SoCs
are no longer dependent on the gpio driver. Remove the dependency
from Kconfig.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Added board definitions for nucleo_f756zg. Features include gpio,
pinmux, uart (ST Zio, ST-Link and Arduino Uno v3 interfaces).
Added basic documentation and some soc definitions for the
stm32 f756XX soc.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
The various linker scripts on arc would include autoconf.h in the arch
linker script but might have CONFIG_ symbols referenced in the soc
specific linker script. Move autoconf.h inclusion to top of the soc
specific linker script out of the arch specific one so we know
autoconf.h is seen before any CONFIG_ references.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
