Add soc and dts files to support for most of the common peripherals
in the STM32G4 series. Add specific support for the STM32G431RB.
Signed-off-by: Richard Osterloh <richard.osterloh@gmail.com>
Add KConfig board support to match board jumper settings
Failing to update bank selection will affect GPIOs tied to VTR3
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
This patch re-namespaces global variables and functions
that are used only within the arch/arm/ code to be
prefixed with z_arm_.
Some instances of CamelCase have been corrected.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add a set of build time assertions that checks if the peripheral base
addresses defined in dts nodes match the values provided by nrfx/MDK.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable CMSDK GPIO driver on v2m_musca_b1 SoC/Board. Add LEDs that are
on the board and init the pinmux for those LEDs to work.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds support for Kinestis K22
Co-authored-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Co-authored-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Co-authored-by: Tom Burdick <thomas.burdick@gmail.com>
Signed-off-by: Tom Burdick <thomas.burdick@gmail.com>
We shall not include core kernel headers in soc.h
header of ARM SoCs. We should try to only include
the vendor headers and auto-generated board header
from DTS. This commit implements this policy for
the SoCs, whose builds have shown to fail due to
header inclusion cycles.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This file contains redundant definitions of a bunch of nRF IRQ numbers
(not all, however) that only generates confusion, as enumeration values
provided by MDK can be used instead.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This change is done so that there is no need to additionaly include
<nrfx.h> before <soc/nrfx_coredep.h> (what might be a bit surprising)
and so that <nrfx_config.h> doesn't need to be include separately for
nRF SoCs requiring a special mapping of peripheral accessing symbols.
This commit removes also no longer needed inclusions and updates
the hal_nordic module with required minor correction of nrfx_glue.h.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Header files of nrfx HALs are not supposed to be included directly
but only with their names prepended with the hal/ directory (so that
an inclusion of an nrfx HAL header clearly differs from an inclusion
of an nrfx driver header).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
A commit that organizes the soc.h header of NXP SoCs:
- removing redundant inclusions of sys/util.h
- removing inclusions of device.h and kernel_includes.h
- including the auto-generated DTS board header
- including the fsl_common.h header
- fixing minor style issues
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We, now, have multiple nRF52x SoCs with 2.4GHz
Radio with LE Coded PHY Capabilities. Therefore,
we would like to have a Kconfig option and select
it in the corresponding SoCs. This allows us to
simplify several #ifdef blocks in the nRF Bluetooth
Controller that would, otherwise, require listing
all nRF SoCS with LE Coded PHY support.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Enable CMSDK GPIO driver on v2m_musca SoC/Board. Add LEDs that are on
the board and init the pinmux for those LEDs to work.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A 16bits on/off based PWM, found on MEC1501.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Add RTC timer driver for CC13X2/CC26X2, and use it instead of systick
as system clock. It is necessary to use this timer for power
management support, so that the system can exit from deep sleep upon
expiry of timeouts.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
No users of this driver after dropping quark platforms.
COUNTER_0_NAME was only defined by the QMSI driver and was defined but
not used in DTS fixup files of ateml_sam0 SoCs. Removing those leftover
defines as well.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
RT SOCs have several memory areas (OCRAMs, DTCM, ITCM, SDRAM, FLASH...)
but only two are selected for FLASH (code) and RAM (data).
It would be good to let the linker be aware about other regions, which
could then be used by drivers or application to create dedicated
sections and relocate memory. For example if we have code in ITCM and
data in DTCM, we still need a dma-able region/section for e.g.
video/camera buffers.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
There are 2 other timers that could be selected, let's just take the
first 32bits one. This should be sufficient to verify the driver.
Enabling the timer in relevant board's dts file as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Such basic timer is found on MEC150x for instance.
Since instances have dedicated data, let's define specifice instance
based on unique DT base address definition.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Refactors the kinetis flash configuration field so it can be shared
across all kinetis SoCs. Defaults are overridden for the k8x and ke1xf
series to preserve values used prior to this refactoring.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Kinetis SoCs have a 16-byte flash configuration field that must be
loaded at a specific address in flash. This field is not needed if we
are building an image to be chainloaded by MCUboot or a RAM-only image,
so we can exlude it in these cases and recover some wasted flash.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Convert use of dt_int_val/dt_hex_val to dt_node_reg_{addr,size}. As
we want to remove dt_int_val/dt_hex_val.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert how we get the various chosen properties like "zephyr,console"
to use the new kconfig functions like dt_chosen_to_label.
Because of how kconfig parses things we define a set of variables of the
form DT_CHOSEN_Z_<PROP> since comma's are parsed as field seperators in
macros.
This conversion allows us to remove code in gen_defines.py for the
following chosen properties:
zephyr,console
zephyr,shell-uart
zephyr,bt-uart
zephyr,uart-pipe
zephyr,bt-mon-uart
zephyr,uart-mcumgr
zephyr,bt-c2h-uart
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configuration item custom busy wait is required for all MEC1501
series if its RTOS timer driver is enabled. We moved the selection
of the timer from board level to MEC1501 SoC level.
Frequency selection remains at the board level.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Enables the arm v7m mpu on the lpc54114 m4 core. Reuses the mpu
configuration from the i.mx rt, which has the same mpu.
Tested on hardware with tests/kernel/mem_protect
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The driver for STM32's independent watchdog already exists and is
compatible with the stm32wb SoC. Enable the independent watchdog
for the stm32wb series for use with this driver.
Signed-off-by: Robert Weber <robertweber95@gmail.com>
