Update to shim driver compatible with the hardware block
in S32K344. Configure the pins before initializing I2C
to avoid happening bus busy.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Reuse existing MCUX-based shim driver for FlexCAN.
Enable flexcan0 for Zephyr canbus to run tests.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Adds driver for pwm on xmc4xxx using Capture Compare Unit 8 (CCU8)
module. There are two CCU8 nodes with each one having four slices.
Each slice has two output channels.
Unlike CCU4, this module can generate complementary high-side/low-side
signals for each output channel. A variable dead time can be added
during the off to on transitions to make sure that the
high-side/low-side signals are not on at the same time.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Adds driver for pwm on xmc4xxx using Capture Compare Unit 4 (CCU4)
module. There are four CCU4 with each one having four channels
Thus it's possible to have up to 16 pwm output signals. The output of
each channel can only be connected to a specific port/pin. The possible
connection and gpio configurations are defined using pinctrl.
The CCU4 module also has a capture mode. Capture support will be added
in the future.
Signed-off-by: Andriy Gelman <andriy.gelman@gmail.com>
Pinmuxing is now done by a pinctrl driver, not by board.c,
so the code used previously for pinmuxing can be removed.
Fixes#59186.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
Introduces support for SoC-specific input-edge-detect configuration to
the CC13/26xx pinctrl driver.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
CC13/26xx's pinctrl_cc13xx_cc26xx.c driver included ioc.h and
(indirectly) pinctrl_soc.h which contained duplicate defines.
This change removes the header conflict and redundant definitions.
This prepares for subsequent changes in this change set that add
additional flags to the pinctrl driver which would otherwise trigger the
header conflict.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
- use CONFIG_HAS_HW_NRF_* symbols consistently in nRF multi-instance
drivers when creating particular driver instances
- remove unnecessary hidden Kconfig options that indicated the type of
peripheral to be used by a given instance (e.g. SPI, SPIM, or SPIS)
and enabled proper nrfx driver instance; instead, use one option per
peripheral type and include the corresponding shim driver flavor into
compilation basing on that option (not the one that enables the nrfx
driver as it was incorrectly done so far in some cases)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Some EFR32 build broke after 3d2194f11e with:
pm.c:152: undefined reference to `pm_state_exit_post_ops'
Add an extra empty function to make this one build again.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Added dts additions for stm32f105xb cpu which is the same as existing
stm32f105xc with less flash.
Signed-off-by: Mathieu Anquetin <mathieu.anquetin@groupe-cahors.com>
This CL attempts to implement npcx's flash driver instead of the
original one (npcx spi driver plus spi_nor flash driver).
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add a new pinctrl type to control peripheral modules' specific IO
characteristics such as tri-state, the power supply type selection (3.3V
or 1.8V), and so on. In NPCX series, the corresponding registers/fields
are irregular. This CL wraps these definitions to dt nodes and put them
in pinctrl property if needed.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Remove unnecessary __weak attribute from power management functions.
These functions are now defined once, globally, and mandatory for
systems that support CONFIG_PM.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add a new Kconfig option that has to be selected by SoCs providing PM
hooks. This option will be now required to enable CONFIG_PM. Before this
change, CONFIG_PM could always be enabled, regardless of SoC providing
any kind of low-power support.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Updated the clock init to reflect the sdk also
updated the clock frequencies to reflect the
respective soc clock values, this file originally
contained unexpected clock values, updated comments
to reflect changes and got rid of doxygen style
comments
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\xmc47_relax_kit board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
Removes duplicate code and inconsistencies in the naming of the
cc13xx_cc26xx devicetree and RTC driver hierarchy and alignes it with
the actual TI product series naming hierarchy.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
On nRF5340 net core it was observed that when `wfi` instruction was
followed by `pop {r0, lr}` in the `arch_cpu_idle` function,
the value of `lr` sometimes got read as 0 from memory despite
having correct value stored in the memory.
This commit inserts additional `nop` instruction after waking up
to delay access to the memory.
Signed-off-by: Andrzej Kuroś <andrzej.kuros@nordicsemi.no>
Reuse existing MCUX-based shim driver for LPUART that is compatible with
the hardware block in S32K344. DMA is not yet supported.
Use the board's debug connector (P6 / LPUART2) as default console.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Unify the pinctrl_soc.h header for all the NXP S32 family by using
the HAL macros that expose the features supported on specific
devices. This approach still need a different binding for each device to
expose in DT different properties and allowed values.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Introduce minimal power initialization for NXP S32 SoCs and allow to
reset the SoC through the sys_reboot() API.
Presently only S32K3 SoCs is supported but it can be extended later to
other NXP S32 SoCs, hence it's placed in a common directory.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The S32K3 MCUs are 32-bit Arm Cortex-M7-based microcontrollers with a
focus on automotive and industrial applications. The S32K344 features
a lock-step core, internal flash, RAM and TCM with ECC.
Co-authored-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
Co-authored-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
NMI_INIT() is now a no-op, so remove it from all SoC code. Also remove
the irq lock/unlock pattern as it was likely a cause of copy&paste when
NMI_INIT() was called.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This patch sets ENET2 ref clock to be generated by External OSC
ENET2 ref clock direction as output
ENET2 ref clk frequency to 50MHz
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
A known issue exists that does not allow a CC13/26x2R device to
establish a link to a CC13/26x2P device unless the capacitor array is
tuned to a non-default value in the P device.
See SimpleLink(TM) cc13xx_cc26xx SDK 6.20+ Release Notes, Known Issues.
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
All Cortex-M processors can support RTT by default. This change enables
RTT support for the cc13xx/cc26xx SoC series (tested in hardware on
CC1352R).
Signed-off-by: Florian Grandel <fgrandel@code-for-humans.de>
