This adds interrupt support to the SAM0 GPIO driver. This is heavily
inspired by @nzmichaelh work in #5715. The primary difference
from that implementation is that here the External Interrupt
Controller (EIC) is separated out into an interrupt controller driver
that is less tightly coupled to the GPIO API. Instead it implements
more of a conversion from the EIC's own odd multiplexing to a more
traditional port and pin mask IRQ-like callback. Unfortunately,
through the EIC on the SAMD2x are relatively well behaved
in terms of pin to EIC line mappings, other chips that share the
peripheral interface are not. So the EIC driver implements a
per-line lookup to the pin and port pair using definitions extracted
from the ASF headers.
The EIC driver still makes some assumptions about how it will be used:
mostly it assumes exactly one callback per port. This should be fine
as the only intended user is the GPIO driver itself.
This has been tested with some simple programs and with
tests/drivers/gpio/gpio_basic_api on a SAMD21 breakout and an
adafruit_trinket_m0 board.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds a SERCOM I2C driver for SAM0 series chips.
Tested with a SAMD21 chip on a SSD1306 display and a MLX90393
sensor. Only compile tested for SAMD20 and SAMR21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Moves the flash memory definitions from Kconfig to device tree for the
rv32m1 ri5cy and zero-riscy cores.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moves the sram memory definitions from Kconfig to device tree for the
rv32m1 ri5cy and zero-riscy cores.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors peripheral addresses, clocks, and compatibles from the ri5cy
core dtsi into a common soc dtsi, then attaches interrupts in
core-specific dtsi files.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The UARTs are on the SoC, not the board, so move their descriptors
to the SoC-level. Also turn on auto IRQ detection as these are PCI-
attached and their IRQs are subject to change depending upon firmware
settings.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Add initial support for the TI CC13x2 / CC26x2 series with the CC2652R
and CC1352R SoCs. The UART and GPIO peripherals are supported. Drivers
use the driverlib HAL from the TI CC13x2 / CC26x2 SDK.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Implementation of pinmux for the stm32mp157c_dk2 board.
Some UART pin mux definition has been added (mainly for
UART console and UART/SPI Arduino shield support).
This can be completed with pin mux for other stm32mp157c
UART.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for stm32mp1 basic UART API with Zephyr.
UART Console and UART shell are also supported.
Async UART API and USART support is to be done.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Move SERCOM peripherals to use the raw defines generated from DTS
parsing. This adds aliases to the DTS so that the SERCOM number
can still be used for clocking and pinmux.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds support for the SAM0 DMA Controller (DMAC). Chained
transfer are not currently implemented.
Tested with tests/drivers/dma/loop_transfer and custom modifications
to that test using three parallel reloading channels. Also tested
with a trivial program that did memory->serial.
Signed-off-by: Michael Hope <mlhx@google.com>
[hageman@inthat.cloud: Rebased and updated commit message]
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds support for the async API for SAM0 SERCOM SPI using
DMA to drive the device. This implementation does the reload
for both transmit and receive in the receive DMA handler.
Doing this simplifies the implementation but means that the
transmit drains completely, resulting in the SPI clock pausing
between buffers while both are reloaded in the receive handler.
Tested with tests/drivers/spi/spi_loopback and several simple
programs monitored with a logic analyzer.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Initial support for Microchip MEC1501 series is added to the tree.
Additional support for UART is also included. This SoC supports
two operational modes for interrupts (Direct and Aggregated). For
this commit, the direct capable interrupts are configured in
direct mode.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Adds Atmel SAMR21 soc which is based on SAMD21, but with a AT86RF233
radio connected internally via SPI.
The AT86RF233 is not yet supprted by Zephyr at this point.
This code is very much copy & paste from atmel_sam0/samd21
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
This commit adds a flash driver implementation that writes to RAM and
exports statistics through stats.h. It can be used to simulate flash
memory for testing purposes.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
The GPIO driver for the Intel Apollo Lake has so many pins it has to
export ten devices to shoehorn its one device into the GPIO API. The
current implementation uses the shared IRQ driver because these
pseudodevices all share one IRQ. However, since the GPIO driver is
aware of all the possible interrupt sources, it's smaller and faster
(and not even messy) to handle it internally, so this patch eliminates
the dependency on the shared IRQ driver.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Add USART1 and LPUART1 nodes on stm32wb series.
Only these 2 ones are available for now on this series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add GPIO support to stm32wb series.
Only ABCDE and H ports are available for now on this series.
Accordingly, update series dtsi file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support to stm32wb series in stm32 clock_control driver.
Ip is similar to stm32l4 one but AHB bus presacler is renamed
to "CPU1" and CPU2 and AHB4 prescalers should be defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Implementation of AMS (Austria Micro Systems) ENS210 temperature and
relative humidity sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Add driver support for Atmel SAM0 device ID, which is 16-bytes long.
The device ID can simply be read from memory at a known location, but
the location is only described in the data sheet, not in ASF.
For SAMD2x it's 0x0080A00C, 0x0080A040, 0x0080A044 & 0x0080A048.
For SAMD5x it's 0x008061FC, 0x00806010, 0x00806014 & 0x00806018.
This adds a new property to the device tree to define the device ID
registers for this SoC family.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Add driver and device tree binding for the Low Power Inter-Integrated
Circuit (LPI2C) controllers found in the RV32M1 RI5CY SoC.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This commit adds CAN support for nucleo F746zg.
Furtermore CAN was added in stm32f7.dtsi and pinmuc_stm32f7.h
CAN_RX: PD0, CAN_TX: PD1
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Add support for pulsing the hardware reset pin of the FXOS8700 high
during initialization.
According to the datasheet, this is required for the I2C/SPI bus
auto-detection logic to work properly if the VDD/VDDIO power
sequencing order cannot be guaranteed.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
2 identical packages were defined for stm32f412 SoC, invariant "g".
Merge them in new sinclge stm32f412Xg.dtsi.
Update matching boards accordinlgy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
