The Quark D2000 is the only x86 with an MVIC, and since support for
it has been dropped, the interrupt controller is orphaned. Removed.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Removed Quark D2000 SoC files and first-order related DT bindings.
A few config options have been moved from the CONFIG_* space to
the DT_* space, as they were defined in the D2000 Kconfig files
and "leaked" into the other Quark trees.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Allow individual specification of the time quanta used for the CAN bus
propagation segment and phase segment 1.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Several bindings have an expectation of sub-nodes that describe the
actual infomation. The sub-nodes don't have any compatiable so we can't
key on that.
So we can add the concept of a sub-node to the YAML to handle cases like
'gpio-keys', 'gpio-leds', 'pwm-leds', etc..
The sub-node in the YAML is effective the "binding" params that describe
what properties should exist in the sub-node.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The binding specified 2 cells for an interrupt, but in reality we only
have an IRQ number. Remove the 'pri' cell from the binding to match
what the dts files are doing.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The pinctrl property in the bindings is meaningless, lets remove it and
add a proper pinctrl property when we are ready.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Added support for the STM32L496XE series with 512KB internal flash and
256KB SRAM of contiguous addresses.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
* Fix white space in phy.yaml
* Fix property name in st,stm32-usbphyc.yaml and usb-nop-xceiv.yaml to
use "#phy-cells" and not "phy-cells"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce uint8-array type for local-mac-address as we need to
distinguish it from 'array' meaning a uint32 array.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
* Rename stringlist to string-array to be closer inline with upstream
dtschema definitions.
* Add string-array to the device_node.yaml.template
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
TI_HDC Driver now also supports waiting for conversion to finish instead
of waiting for GPIO interrupt.
Signed-off-by: Nikos Oikonomou <nikoikonomou92@gmail.com>
Hdc1008 driver is renamed into ti_hdc to prepare it to support all
available Texas Instruments HDC sensors (e.g. hdc1080, hdc2080).
Signed-off-by: Nikos Oikonomou <nikoikonomou92@gmail.com>
This commit adds counter driver based on RTCC module for SiLabs Gecko
SoCs.
Tested with SLWSTK6061A / BRD4250B wireless starter kit.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Move common properties like 'compatible', 'reg', 'reg-names',
'interrupts', 'interrupt-names', and 'label' into one common base.yaml
that all the other yaml's can inherit from. This removes both
duplication and inconsistent definition.
The device specific yamls just need to say if a property is 'required'
or not.
NOTE: due to some generation conflicts we did not covert
'soc-nv-flash.yaml' to use base.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We've never propertly generated any pinmux info, so remove generation
from the binding yaml files for pinmux properties.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
stm32wb55rg is a dual core SoC (M4/M0) with a radio/protocol stack
running on M0 core. M0 FW starts at flash address 0x80CB000.
So flash size available to zephyr is 812K instead of 1M.
Configure package size to reflect this (flash size is now 812K)
and update MPU setting to exclude M0 FW. From MPU point of view,
we set flash size to 512K since we should chose a size being a power
of 2.
If we consider there will be 2 images partitions in a FOTA scheme,
512 K is beyond image-0 and hence is sufficient to cover application
image.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
sram2a and sram2b where defined in the prospect of defining
HCI shared memory sections from device tree.
Remove them, since this is not the case anymore.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since Kconfig is responsible for enabling/disabling devices at build,
the devices in dt are defaulted to status="ok" to keep the output in
generated_dts_board.conf the same across configurations and simplify
the board-level dts files.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
