This adds support for the async API for SAM0 SERCOM USARTs using
DMA to drive the device.
Tested on SAMD21 with a few trivial programs and with
tests/drivers/uart/uart_async_api.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds support for the basic timer counter (TC) found on SAM0
series parts. This driver only supports running the counter
in 32 bit wide mode. Since this mode explicitly slaves the odd
counters to the even ones, only instances of the even ones are
defined.
Tested with tests/drivers/counter/counter_basic_api on SAMD21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add support for the Low Power Inter-Integrated Circuit (LPI2C)
controllers found in the NXP Kinetis KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The node name for device_id was device_id@0 it should be
device_id@80a00c to reflect the first register region
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
import linux-v5.1:Documentation/devicetree/bindings/vendor-prefixes.txt
Use vendor-prefixes.txt to check vendor prefixes
used in compatible strings and property names.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Previous the register size was 1M, technically the there are only a
small handful of registers defined in the IOAPIC, so shrinking the size
to 4k, so its as most one page large.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The IOAPIC node shouldn't have been in the cpu container, especially
since the cpu container does:
#address-cells = <1>;
#size-cells = <0>;
So the reg field of the IOAPIC would be treated as 2 registers instead
of a register and size. Move IOAPIC node out of the CPU node fixes this
issue.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Apollo Lake devicetree is augmented with its 8 I2C interfaces.
The default number of dynamic IRQ stubs is increased to deal with
these new interfaces having IRQ vector detection at runtime.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The legacy PCI support in the DesignWare I2C driver is replaced with
the new PCIe support. The Intel Quark X1000 SoC and the galileo board
configurations are updated accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The SARA-R4 series modules from U-Blox are size-optimized LTE-M /
NB-IoT and EGPRS modules designed for low power consumption and
longer battery life.
The binding identifies the UART device, power GPIO and reset GPIO
lines.
Signed-off-by: Michael Scott <mike@foundries.io>
The label binding was missed during initial development of the
WNC-M14A2A modem. Let's add the binding so that during the
migration to a shield, we can update the DTS correctly.
Signed-off-by: Michael Scott <mike@foundries.io>
ARM SysTick peripheral is optional in Cortex-M0 MCUs,
so we delete the respective dts node when the peripheral
is not present.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Atmel SAM D series SoC variants (present in the tree) all have
an ARM Cortex-M0+ core, not a Cortex-M0, so we correct this in
the .dtsi header.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Unlike Cortex-M3 and Cortex-M4, in Cortex-M7 the number of
MPU regions may vary based on the implementation. This commit
adds a DTS node for the ARM MPU peripheral in the device tree
of Cortex-M7 SoCs and updates the fixup files, so we may extract
the number of MPU regions at build time. SoCs:
- nxp_rt
- same70
- stm32f7
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds a DTS node for the ARM MPU peripheral in the
device tree of ARMv8-M SoCs (for the secure and the non-secure
DTS descriptions) and updates the fixup files. SoCs:
- nrf9160
- musca_a
- musca_b1
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add DTS binding files for the ARM MPU, for both ARM
MPU architecture variants, ARMv7-M and ARMv8-M.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add enum to list what values of maximum-speed are exceptable since
enum's get represented as strings in DT. This also allows us to
generate a code enum to correspond to the string.
We also introduce include/dt-bindings/usb/usb.h which is a hand coded
definition of the enum. We don't have a great way to generate this
right now, however it would be better if we did.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
MHU (Message Handling Unit) enables software to raise interrupts to
the processor cores. It is enabled in SSE 200 subsystems.
This patch aims to implement inter processor communication.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Add LiteX with softcore CPU VexRiscV SoC definitions and default
configurations.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add LiteX interrupt controller driver and bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add LiteX timer driver with bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add LiteX UART driver with bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Adding missing erase-block-size entries for the flash-controller
nodes in the nrf52810 and nrf52811 .dtsi files.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Move flash-controller and SRAM node definitions under SoC node.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Reduced Kconfig for counter with nRF TIMER and RTC. Added overlays
for TIMER and RTC configuration in the counter test.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add support for CLKOUT source selection and divider as found on the
NXP Kinetis KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add a new clock control driver for NXP Kinetis SoCs that have the
Peripheral Clock Controller module (PCC).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit adds basic support for nrf52811 in the arch SoC, dts
and nrfx folders.
The nRF52811 is a Bluetooth 5.1 Direction Finding SoC with comprehensive
protocol support.
The nRF52811 SoC is capable of the latest features of Bluetooth 5.1,
the most prominent being Direction Finding.
The radio in the nRF52811 SoC has comprehensive protocol capabilities,
including Bluetooth 5.1 Directing Finding, all Bluetooth 5 features,
802.15.4, Thread, Zigbee, ANT and 2.4 GHz proprietary.
It has 4 dBm TX power and has been optimized to offer the best RX
sensitivity of all SoCs in the nRF52 series.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Add flash and SRAM to the Microsemi MiV device tree.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add bindings for SiFive Data Tightly-Integrated Memory.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
add usbd1 definition to rt dts file,
set EHCI controller config default value in rt1050 default config file,
add EHCI controller driver MACROs to dts_fixup.h,
initialize EHCI clock in rt soc.c
add HAS_MCUX_USB_EHCI for supported soc in Kconfig.soc
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
Dts Nodes for all the GPIO portswere defined. In addition,
a new binding file was created for the gpio driver.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Expose MEC1501 5 I2C/SMB controllers
Add Microchip specific I2C device tree properties
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
All series of stm32 have at least one ADC instance and this commit adds
one ADC node to the root dts file of each soc, and also adds fixing up
mappings to them.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
The HT16K33 is a memory mapping, multifunction LED controller
driver. The controller supports up to 128 LEDs (up to 16 rows and 8
commons) and matrix key scan circuit of up to 13x3 keys.
This commit adds support for the keyscan functionality of the HT16K33.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The HT16K33 is a memory mapping, multifunction LED controller
driver. The controller supports up to 128 LEDs (up to 16 rows and 8
commons) and matrix key scan circuit of up to 13x3 keys.
This commit add support for the LED driver functionality of the
HT16K33.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
