STM32F103 micros starting from 64-pin (xE) packages upward have
available port G. This patch defines a dts binding for them.
Signed-off-by: Pavel Kral <pavel.kral@omsquare.com>
Add #pwm-cells to the i.MX PWM binding and dts files. This is to
support have a pwms clients work properly.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add #pwm-cells to the STM32 PWM binding and dts files. This is to
support have a pwms clients work properly.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Newer DTC now warns about mismatch between the reg and unit-address.
Most of these cases are due to case not matching, so fix thoses so
everything is lowercase.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The information extracted from the device tree is now used to initialize
GPIO device instances. Up until now the GPIO device driver made no use
of this information. Actual instance creation is still controlled using
the Kconfig method. Missing GPIO device tree nodes were added in the
process for STM32L073, STM32F413 and STM32F373.
The information for gpio instance initialization has already been
present for supported STM32 SoCs but remained unused. Changes in the
device tree had no effect on GPIO functionality and was essentially
redundant. Using the device tree for hardware description seems
plausible and less painful than a myriad of defines in some SoC
description header.
The change was implemented under the assumption that current device
trees provide a correct description of the SoCs. Base register addresses
and RCC register bits were not explicitly checked for each device.
Manual tests were executed on:
- NUCLEO-F103RB
- STM32F429I-DISCO
- STM32F746G-DISCO
- NUCLEO-F767ZI
Manual tests consisted of blinky on different GPIOs and pins on each
board.
sanitycheck was executed for all STM32 based boards
Fixes: #10629
Signed-off-by: Martin Bertsche <martin72216@googlemail.com>
Update stm32f469i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
-Update yaml file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32l496g_disco configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update disco_l475_iot1 configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The only difference between the F413xH and F413xG is flash memory size.
STMF413xH: 1536 Kbytes
STMF413xG: 1024 Kbytes
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
This patch adds a USB device driver for the USBHS device that can be
found on Atmel SAM E70 SoC family. Only the FIFO mode is supported
(as opposed to DMA). It supports LS, FS and HS modes, but defaults to
FS mode as Zephyr does not fully support HS mode yet.
Tested examples on an Atmel SMART SAM E70 Xplained Board:
* usb/cdc_acm
* usb/hid-mouse
* usb/mass
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add clocks property in stm32l4r5 devices.
Replace i2c2 node by i2c3 node in l4.dtsi as i2c3 available
in all stm32l4 SoCs while i2c2 is not available in some parts.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add dts binding and info for TRNG device and enable basic support to
get the device name from DTS. We leave for now the base addresses
coming from the MCUX HAL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add dts binding and info for RNGA device and enable basic support to
get the device name from DTS. We leave for now the base addresses
coming from the MCUX HAL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add #pwm-cells properties to kinetis dts files and update the yaml
binding to spec the two cells as pin and period (in nanosecond to match
Linux Kernel binding spec).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert gpio_cc32xx driver over to using device tree. Added binding
files, updates to dts for various SoCs that use cc32xx.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adding watchdog driver for sam SoC. The current implemntation just
diables the watchdog on device boot.
This PR adds the following support for SAM3X, SAM4S and SAME70
1. Activate processor reset
2. Activate all reset
3. Generate interrupt on watchdog timer expiration.
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Silicon Labs EFR32MG12P Mighty Gecko MCU includes:
* Cortex-M4F core at 40MHz
* up to 1024KB of flash and 256KB of RAM
* integrated Sub-GHz and/or 2.4GHz radio
* multiple low power peripherals
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Signed-off-by: Endre Karlson <endre.karslon@gmail.com>
Partially replaces Kinetis MCUX driver configuration from Kconfig to
Device Tree. Interrputs moved from defines configuration to DT.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Introduces the location property and adds the ability to use values
generated by the device tree configuration.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add I2S bus initial support to stm32f4 SOC family.
On stm32f4 the I2S shares same controller as SPI, so
the declarations have been adapted from SPI ones.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The Silicon Labs EFM32 Happy Gecko MCU includes:
* Cortex-M0+ core at 24MHz
* Up to 64KB of flash and 8KB of RAM
* Full speed (12 MHz) USB 2.0 Device
* Multiple low power peripherals
Signed-off-by: Marcio Montenegro <mtuxpe@gmail.com>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Convert gpio_gecko driver over to using device tree. Added binding
files, updates to dts for various SoCs that use gpio_gecko.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add maximum-speed property to usb nodes and set it to
their maximum on-chip PHY capability.
SoCs with USB device controllers only support full
speed, so we don't add maximum-speed to these nodes.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The gpio controllers on SAM4S, SAME70, and SAMD were missing properties
related to GPIO pin generation. Add the missing details into the yaml
and dts files to allow boards to specific gpio pins.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
added sam4s16b, sam4s8c, sam4s8b, sam4s4c, sam4s4b,
sam4s4a, sam4s2c, sam4s2b and sam4s2a.
Used the same order as in the data sheet and code structure
equal to same70. Updated the sam4s_xplained board to match
the altered .dtsi location of the specific SoC.
Signed-off-by: Vincent van der Locht <vincent@vlotech.nl>
This patch adds timers and PWM nodes to STM32 F7 series, as well as the
corresponding dts fixup entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that we've cleaned up all the STM32 related .dtsi files we don't
use dts/arm/st/mem.h so we can remove it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F7 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F3 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F2 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the L4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the L0 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F1 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F0 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added initial support and created the corresponding device tree part for
building PSoC6 SoC as part of Zephyr.
Signed-off-by: Nazar Chornenkyy <nazar.chornenkyy@cypress.com>
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
Commit introduces support for ARM TrustZone CryptoCell 310
for Nordic Semiconductor nRF SoCs in device tree.
Signed-off-by: Dominik Kilian <Dominik.Kilian@nordicsemi.no>
