The STM32F723 has more interrupts than the STM32F746 due to the
additional SDMMC controller. Besides that the changes are very
similar to the ones of the STM32F746.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch includes:
STM32F7 family device tree file with basic and UART definitions.
STM32F746 subfamily device tree file.
Memory definitions for STM32F746xG subfamily.
Signed-off-by: Yurii Hamann <yurii@hamann.site>
STM32F412/413/446/469 SoCs have 6 bidirectional endpoints
according to the reference manuals RM0402, RM0430,
RM0390 and RM0386.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This commit moves the definitions for the LED and Buttons
supported in nrf52810_pca10040 DK in DTS from board.h. Aliases
are kept in board.h to make basic examples pass.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The nRF52810 is a low-cost variant of the nRF52832, with a reduced set
of peripherals and memory. This commit adds basic support for it in the
arch SoC and dts folders.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Ioannis Glaropoulos <ioannis.glaropoulos@nordicsemi.no>
The i.MX 6SoloX SoC is a hybrid multi-core processor composed by one
Cortex A9 core and one Cortex M4 core.
Zephyr was ported to run on the M4 core. In a later release, it will
also communicate with the A9 core (running Linux) via RPMsg.
The low level drivers come from NXP FreeRTOS BSP and are located at
ext/hal/nxp/imx. More details can be found at ext/hal/nxp/imx/README
The A9 core is responsible to load the M4 binary application into the
RAM, put the M4 in reset, set the M4 Program Counter and Stack Pointer,
and get the M4 out of reset.
The A9 can perform these steps at bootloader level after the Linux
system has booted.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
The various STM32 reference manuals sometimes define the USB endpoints
as IN or OUT only and sometimes as bidirectional, even in the same
manual. This is likely because the OTG implementation has one set of
registers for the IN endpoints and one other set for OUT endpoints.
However at the end a given endpoint address can both transmit and
receive data.
This causes some confusion how to declare the endpoints in the device
tree, and depending on the SoC, they are either the same number of IN
and OUT endpoints declared, or they are declared as bidirectional. At
the end it doesn't really matter given how the driver uses those values:
#define NUM_IN_EP (CONFIG_USB_NUM_BIDIR_ENDPOINTS + \
CONFIG_USB_NUM_IN_ENDPOINTS)
#define NUM_OUT_EP (CONFIG_USB_NUM_BIDIR_ENDPOINTS + \
CONFIG_USB_NUM_OUT_ENDPOINTS)
#define NUM_BIDIR_EP NUM_OUT_EP
This patch therefore cleanup the driver, the DTS, and the DTS fixups to
only define the number of bidirectional endpoints.
In addition to the cleanup, that fixes a regression introduced by commit
52eacf16a2 ("driver: usb: add check for endpoint capabilities"), which
introduced a wrong check for SoC only defining the number of
bidirectional endpoints.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This commit enables CAN on the STM32L432.
Tested on nucleo l432ck with external transceiver and loopback mode.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit splits the common interrupt into rx and tx parts because
only STM32F0 series has a common interrupt.
Moved clock source definition to device-tree.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
The prepended 0x causes DTC warnings and shouldn't be there.
Tested by compiling hello_world for nrf52840_pca10056 before and after.
Fixes#8334.
Signed-off-by: Alex Tereschenko <alext.mkrs@gmail.com>
This adds basic support for declaring gpio nodes in dts for nrf52.
The dts.fixup provides mapping for the generated defines to the config
defines currently used by the nrf gpio driver.
Existing boards that use nrf52 are updated.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
This commit moves the bit timing (PROP, BS1, BS2 segments and SWJ)
from Kconfig to the device-tree and fixes issue #7933
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Enable supporting UART4 on STM32F107 and STM32F103Xe SoCs.
Modified stm32f1/dts.fixup for replacing USART with UART.
Signed-off-by: Jun Li <jun.r.li@intel.com>
LPUART (Low-power UART) peripheral is just like ordinary U(S)ART
which lives in a separate clock/power domain.
Therefore already existing code could be reused as is
almost entirely.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
The STM32L432 SoC has a standard non-OTG USB controller. Add an entry
for it in stm32l432.dtsi and add the corresponding DTS fixup entries.
The controller is kept disabled and should be enabled at the board
level.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
USB OTG is currently enable for the whole STM32L4 family, while only a
few of them actually support it:
- STM32L475, STM32L476 and STM32L496 have an OTG controller
- STM32L432, STM32L433 and STM32L452 have an USB controller
- STM32L431, STM32L451 and STM32L471 do not have any USB controller
Fix that by moving the DT entry from stm32l4.dtsi to stm32l475.dtsi
and by adding a #ifdef #endif around the corresponding DTS fixup
entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add driver for MCUX mailbox which can be used for lpcxpresso54114
and other lpc and kinetis socs.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Add soc configuration support and dts files for nxp_lpc54xxx_m0.
Adjusted nxp_lpc54xxx soc, configuration and dts files for the
presence of slave core.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds dts bindings for the kinetis watchdog peripheral, and updates the
watchdog nodes for the k64 and kw2xd socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds some DTS information to flesh out the NXP Kinetis
based RTC blocks. DTS fixups were added as well to match up the driver
usage to the DTS output.
Signed-off-by: Andy Gross <agross@kernel.org>
Rename various SoC related defines and files from just being LPC54114
to LPC54114_M4. This is in prep for supporting a build for the second
core on the LPC54114 (the Cortex-M0+).
* Renamed Kconfig SOC_LPC54114 to SOC_LPC54114_M4
* Renamed Kconfig.defconfig.lpc54114 to Kconfig.defconfig.lpc54114_m4
* Introduced nxp_lpc54xxx_m4.dtsi based on nxp_lpc54xxx.dtsi
* Moved some pinmux related defines into SoC code.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Changed define for SETTINGS_CONFIG_PAGE_SIZE from a hard coded value
to reference build system generated FLASH_ERASE_BLOCK_SIZE. This value
comes from 'erase-block-size' found in the dtsi file of devices.
- Modified nrf52840.dtsi to include definition for 'erase-block-size'
Fixes#7107
Signed-off-by: David Leach <david.leach@nxp.com>
Commit introduces support for watchdog configuration for Nordic
Semiconductor nRF SoCs in device tree.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Adds dts bindings for the mcr20a wireless transceiver. The frdm_k64f
board supports the mcr20a via an Arduino shield, therefore the dts node
is added to the board dts. The kw2xd is a SiP and thus the mcr20a dts
node is added to the soc dts.
The networking samples using prj_frdm_k64f_mcr20a.conf have been broken
since the refactoring of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts spi bindings for the kinetis dspi controller, and updates the
k64, kw2xd, kw40z, kw41z dts nodes accordingly.
Updates the dts interrupt priorities to match the board defconfigs
(e.g., boards/arm/frdm_k64f/Kconfig.defconfig)
For k64, fixes an error in the spi1 interrupt number and adds a third
instance (spi2).
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
