For true mmio-sram, arc,iccm, arc,dccm nodes we should not be setting
device_type = "memory". This should be used for true DRAM regions of
memory and not on SoC SRAMs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Several peripherals are non-functional in the ENG_A revision
of nRF5340 (Application MCU) so we delete the corresponding
DTS nodes in the device description.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Rename the nRF5340 QKAA variant .dtsi headers (Application
MCU) by adding an Engineering A (Eng A) suffix. This is done
to indicate that the headers should be explicitly used when
building for a board that contains the Engineeering A nrf5340
SoC variant.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We need to use CPUAPP and CPUNET instead of CPU0 and CPU1
terminology, because those terms are the ones used
throughout the DeviceTree definitions for nRF5340 SoC.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Move the definition of the number of MPU regions
(num-mpu-regions) in a SoC variant-specific header
instead of the common .dtsi for nRF5340 Application
MCU. This allows us to define different SoC variants
with different number of MPU regions available.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit renames the nrf5340_cpuapp_common.dtsi header
to nrf5340_cpuapp_peripherals.dtsi. This name is more
appropriate, as the header contains DT definitions for
peripherals, accessible from either Secure or Non-secure
execution environment (i.e. not accessible exclusively
by Secure or Non-Secure).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds the device tree TCC (Timer/Counter for Control
Applications) peripheral definitions for the Atmel SAM D5x and E5x
series SoCs.
The SAM D5x/E5x series SoCs have five instances of the TCC peripheral:
TCC# Channels Waveform Output Counter Size
0 6 8 24-bit
1 4 8 24-bit
2 3 3 16-bit
3 2 2 16-bit
4 2 2 16-bit
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Add support for STM32L0X using the generic STM32 backend. This is
quite a significant change since the L0 series uses a slightly
different flash controller. Refactor the generic backend to better
support different block sizes and the L0's register interface.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Add initial support for nuvoton numicro m48x SoC series, basic
init and uart functionality are covered with gpio and clock
directly relies on HAL.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
The SAMD21 series has three timer/counters with a mix of channels and
resolutions. Note that the SAMD20 only has TC peripherals and no TCC
peripherals which is why the changes are in samd21.dtsi.
Signed-off-by: Michael Hope <mlhx@google.com>
Timer interrupts have been added for all STM32 SoC. H7 series already
had the interrupt definitions. The IRQ number and names have been taken
from the STM32Cube HAL header files.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add support for the polarity flag in the STM32 PWM driver.
STM32 boards using PWM have been updated accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Aliases defined for peripheral nodes in the nRF SoC definitions were
used in drivers to properly match the hardware instances.
After the drivers were converted to use the new DT API, these aliases
became needless.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable GPIO as a workaround to enable some SPI slaves are not correctly
controlled using the Flexcomm SPI device.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Those MCUs have 2KB RAM and 16KB FLASH memory, but they are still
powerful enough to run small configuration of Zephyr RTOS.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
The STM32L072 and STM32L073 comes with a hardware random number
generator. Add this to the device tree.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
This allows referencing the CPU in the board-specific DTS file.
Also fix warnings by making the addresses lower case.
Signed-off-by: Michael Hope <mlhx@google.com>
Adds a new LPTIM binding for stm32 soc,
based on the timer binding. This will makes a specific filter
on dt_compat_enabled("stm32,lptim")
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The interrupts generated by the generic timer behave in
a level-sensitive manner. Change the DT to reflect the same.
Fixes: #25585
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Add the missing node and bindings. This is a secure-mapped peripheral,
so do not add it to the common include file
nrf5340_cpuapp_common.dtsi.
Fixes: #25493
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
In aarch64 DTs, priority and flags cells have been swapped,
fix the same.
Correct interrupt property per the GIC binding document
looks like:
interrupts = <irq_type irq_num irq_flags irq_priority>;
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Adds the required #io-channel-cells property to kinetis k8x and kv5x
socs. We are now consistently defining this property for all
nxp,kinetis-adc16 compatible nodes.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Allow configuring the clock prescaler divider for the NXP Kinetis
FlexTimer. Setting the prescaler to a lower value allows for much
higher resolution/accuracy for the generated PWM waveforms.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Instead of having a Kconfig property, if there is no local-mac-address
property in the devicetree than we'll generate a unique MAC address
based on unique ID registers on the SoC.
We remove the local-mac-address properties in the SoC dtsi files to
match the default behavior that existed before (ie, unique MAC address)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add infineon xmc series with XMC4500 support. XMC series comes with,
- CPU operates upto 120MHz
- 3 RAM (PSRAM1 - code, DSRAM1 - data and DSRAM2 - communiation)
- upto 1MB flash
init: clock control & gpio is not done, so SoC initialization directly
relies on HAL. Core operating clock is stored in no_init section, which
is kept under DSRAM1. Only DSRAM1 is used until clock support. Using
PSRAM1 and DSRAM1 needs adaptation in linker script - planned for next
revision.
Note: SystemInit cannot be consumed directly due to vector table +
HAL linker dependency.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
This commit adds support for nRF52820 development on nRF52833DK.
Changes afffects:
- Introduce files related to board description.
- Add blank documentation file (for future update).
- configuration files for build process.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
This commit adds basic support for nRF52820 SoC.
Changes affect introducing:
- architecuture files (dtsi)
- configuration of nrfx drivers
- adaptation of inclusions based on chosen SoC
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Add STM32F427. This is mainly aimed towards the stm32f427vi.
Changes:
- Add stm32f427 support based on previous work
done for the stm32f429.
- Rework currunt stm32f429 implimentation to now
be based on stm32f427.
- Introduce dedicated dtsi for the VI variant of both
stm32f427 and stm32f429. This is done to prevent stm32f4.dtsi
from being included twice.
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Update dtsi and pinmux macros for stm32f7 family. Add sdmmc1 to dts file
for stm32f746g_disco. Also add board specific configuration file for
fat_fs sample.
Signed-off-by: Helge Juul <helge@fastmail.com>
Update the dtsi for stm32l471 (which the higher SoCs are based on) to
support the stm32-sdmmc disk access device. Enable the device for the
stm32l496g_disco board, and update the pinmuxing.
Note that the stm32l496g_disco board also has a card detect gpio
(MFX_GPIO8), but this is not supported yet. When not specified the
driver will assume a card is present.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Add initial support for Broadcom Viper SoC.
It has ARM Cortex-M7 and Cortex-A72 cores.
Signed-off-by: Arjun Jyothi <arjun.jyothi@broadcom.com>
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Michael Hope
