The default I2C channel 3 is used by alternate function of GPIO H1/H2
Krabby uses GPIO F2/F3 as I2C channel 3, so we need to add the
compatibility of the GPIO F2/F3.
TEST=test on it8xxx2_evb:
zmake configure -b zephyr/projects/it8xxx2_evb/
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The syscall_perf test cannot be built successfully due to region RAM
overflow on qemu_riscv32_xip and hifive1_revb. The dtim is only 16KB,
To reduce the main stack size to make it can be built successfully.
Base on the spec(fe310-g002-manual-v1p1.pdf), the size of itim should
be 8KB. Modify the definition in its DTS file.
And it also fix some of the gcc warning when testing it by twister.
This PR partially fixes#41399.
Signed-off-by: Enjia Mai <enjia.mai@intel.com>
If there are no console messages input at an interval of 15
seconds, the system will be able to enter suspend mode.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Modifying configuration to enable with gd32vf103
- Add usart definition to devicetree.
- Define USART_STAT as alias of USART_STAT0 if not defined it.
- Enable USART if SOC_SERIES_RISCV_GIGADEVICE_GD32VF103.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Change the settings to support pinctrl on the GD32VF103.
- Split soc/arm/gigadevice/common/pinctrl_soc.h
and put it into include/dt-bindings.
- Leave some definitions that can't handle with device tree compiler
in pinctrl_soc.h.
- Remove dependency to SOC_FAMILY_GD32 because always enabled it
if GD32_HAS_AF(IO)_PINMAX was selected.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Not all boards use the same UART's defaults properties.
This commit updates device tree declarations by deferring
specific definitions to the board's DTS.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
IT8XXX2 uses shared ns16550.c driver which does not provide a power
management callback(pm_action_cb), so create driver to handle
IT8XXX2 specific UART features.
note: pm_action_cb(old name: pm_control_fn)
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Use i2c_hal functions to enable support for
multiple SoCs.
Use DT compat to enable I2C from device
tree configuration
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
This joins all clock control handling to same source
by using hal clock functions. It also brings ESP32C3
clock support.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Add the power state of deep doze. When system enters deep doze, the
clock of CPU and EC can be stopped to reduce power consumption. And
enable the UART Rx WUI before entering deep doze to wake up EC and
CPU.
Tested on it8xxx2_evb board. It will reduce 5.25mA when system enters
deep doze mode.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add devicetree nodes for the NEORV32 GPIO device.
The GPIO port is 64 bits wide, but Zephyr only supports up to 32 bit
wide GPIO ports. The GPIO device is therefore handled as two Zephyr GPIO
devices with a nexus devicetree node mapping pins 0 to 31 to the device
handling the lower half, and pins 32 to 63 to the device handling the
upper half.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
interrupt controller, also places its relevant
peripheral sources allowing drivers to use the
DT macros instead of espressif headers.
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
This patch fixes wrong PLIC irq number of UART and SPI for SiFive
FU740 on HiFive Unmatched. Use samples/subsys/console/echo for
testing.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
This patch adds support for SiFive Freedom U740 SoC.
First version is minimum only using UART, SPI and L2-LIM area.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
This patch adds support for SiFive Freedom U540 SoC.
First version is minimum only using UART, SPI and DDR memory area.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Note that the it8xxx2 does not support a status register so that
functionality is omitted.
This change also adds driver tests that build both the npcx and it8xxx2
drivers.
Signed-off-by: Yuval Peress <peress@chromium.org>
This has an unrecognized vendor prefix which does not seem to serve
any purpose. Removing it is a way forward to turning warnings into
errors on unrecognized vendor prefixes.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
As far as I can tell, 'vexriscv' does not name a vendor:
https://github.com/SpinalHDL/VexRiscv
It also doesn't seem entrenched enough to merit a special case
exception to the de factor rule 'the "vnd,foo" namespace is for
vendors'. This is open to debate and we can revise as needed in the
future, but for now let's just rename the compatible to avoid
triggering warnings/errors about unknown vendors.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This PR will change accessing the related pinctrl macro from soc_dt.h
And the pinctrl of SCL and SDA were got from pinctrl-0 and pinctrl-1,
respectively. Change it to get from pinctrl-0 only.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
