This runs the Timer/Counter for Control in 'normal' PWM mode. The
number of channels and counter width depends on the device and is
imported from DeviceTree.
Signed-off-by: Michael Hope <mlhx@google.com>
If shell is enabled then enable all sub-shells if their dependencies are
satisfied. This was done for some modules and subsystems but was not
consistent.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add support for the polarity flag in the STM32 PWM driver.
STM32 boards using PWM have been updated accordingly.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The PWM drivers has been refactored using the HAL LL API. Not only that,
but the set pin_set function is now faster, as channel output compare is
just initialized if needed.
NOTE: Has been tested using H743zi board for now.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Allow configuring the clock prescaler divider for the NXP Kinetis
FlexTimer. Setting the prescaler to a lower value allows for much
higher resolution/accuracy for the generated PWM waveforms.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The driver-specific config_info structure referenced from the device
structure is marked const. Some drivers fail to preserve that
qualifier when casting the pointer to the driver-specific structure,
violating MISRA 11.8.
Changes produced by scripts/coccinelle/const_config_info.cocci.
Some changes proposed by the script are not included because they
reveal mutation of state through the const pointer, though the
code works as long as the driver-specific object is defined without
the const qualifier.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove semicolon between instance invocations of DT_FOREACH_IMPL_ and
thus DT_INST_FOREACH. This provides more flexibility to the user. This
requires we fixup in tree users to add semicolon where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make drivers multi-instance wherever possible using DT_INST_FOREACH.
This allows removing DT_HAS_DRV_INST in favor of making drivers just
do the right thing regardless of how many instances there are.
There are a few exceptions:
- SoC drivers which use CMake input files (like i2c_dw.c) or otherwise
would require more time to convert than I have at the moment. For the
sake of expediency, just inline the DT_HAS_DRV_INST expansion for
now in these cases.
- SoC drivers which are explicitly single-instance (like the nRF SAADC
driver). Again for the sake of expediency, drop a BUILD_ASSERT in
those cases to make sure the assumption that all supported SoCs have
at most one available instance is valid, failing fast otherwise.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The TPM (Timer/PWM Module) is a 2- to 8-channel timer which supports
input capture, output compare, and the generation of PWM signals to
control electric motor and power management applications.
This patch adds the driver and the binding necessary for instantiating
the driver. The work is based on the RV32M1 driver for TPM done by
Henrik Brix Andersen. A later patch will enable this driver to be used
for the KW41Z SoC, if PWM support is requested.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Following other drivers, Kconfig based instances are now entirely
removed. In order to do this change, PWM nodes in board DT files have
been given a pwm{N} label so that both:
- DT API checks such as #if DT_HAS_NODE(DT_NODELABEL(pwmN)) can be
used (N being PWM instance number).
- DT references can be written as pwms = <&pwmN x y>; instead of
pwms = <&{/soc/timers@XXXXXXXX/pwm} x y>;
This approach is also used on the Linux Kernel.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Move to using NODELABEL references to enable driver instances for
PWM0..3. This will allow us to remove per-instance PWM Kconfig symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Do not assume in the SoC level device trees that NXP Kinetis FlexTimer
nodes will always be configured as PWM. Instead, configure FlexTimer
nodes for PWM at the board level for NXP Kinetis boards.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage. We also remove dts_fixup.h defines that
are no longer needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert drivers that have the following pattern:
#if DT_INST_NODE_HAS_PROP(0, label)
INIT_MACRO(0)
#endif
...
#if DT_INST_NODE_HAS_PROP(n, label)
INIT_MACRO(n)
#endif
to use DT_INST_FOREACH(INIT_MACRO) instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in litex drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in openisa drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in microchip drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in atmel sam drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in sifive drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in STM32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in esp32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change adds waiting until PWM is stopped before restarting it. Without
the change, calling the pwm_nrfx_pin_set function multiple times in
quick succession could cause a race condition causing the PWM to
remain stopped in case it should be restarted.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
Configure the PWM period and pulse width in timer ticks instead of
calculating the frequency and duty cycle for use in the higher level
MCUX API. This improves the resolution of the PWM output signal
considerably.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Update hal_nordic's revision, so that NRFX_ASSERT uses __ASSERT_NO_MSG
directly, not through the assert macro that comes from from libc,
as the definition of the latter might be different when some specific
libc version is used, and this could generate troubles.
Replace also uses of assert() with __ASSERT_NO_MSG() in nrfx driver
shims that use this macro without including the corresponding header
file (i.e. that implicitly rely on assert.h being included from
nrfx_glue.h, which is no longer the case).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
- Updates gpio driver and device tree files to the new GPIO Config flags
- Implements the new port_* APIs
- Update I2C and PWM Drivers to use new GPIO config
- Add esp32.overlay to gpio_basic_api test
- refactor convert_int_type, regs struct
- remove config_polarity
- add kConfig notes
Tests:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_basic_api
- tests/drivers/gpio/gpio_api_1pin
Board:
- esp32 DevKitC V4
Note about interrupts:
The ESP32 requires specifying a CPU interrupt to be used for GPIO
interrupt signals. CPU interrupts can be either level or edge (or
special) triggered, but not both.
Please check gpio/Kconfig.esp32 for more info.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
PWM driver for LiteX SoC builder was created.
Because LiteX supports only one channel for each PWM device,
an appropriate restriction was made.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add support for specifying the PWM signal polarity through flags to
the NXP Kinetis FlexTimer (FTM) PWM driver.
Prior to this change the FTM PWM driver always produced inverted
polarity (active-low) PWM signals.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for requesting an inverted PWM pulse (active-low) when
setting up the period and pulse width of a PWM pin. This is useful
when driving external, active-low circuitry (e.g. an LED) with a PWM
signal.
All in-tree PWM drivers is updated to match the new API signature, but
no driver support for inverted PWM signals is added yet.
All in-tree PWM consumers are updated to pass a flags value of 0
(0 meaning default, which is normal PWM polarity).
Fixes#21384.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert the NXP MCUX FTM driver to use the DT_INST_* defines instead
of a mix of CONFIG_PWM_* and dts fixups. This simplifies adding new
device tree properties to the ftm nodes.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Only emit a warning about changing PWM period for all channels of a
given FTM instance when changing the period from zero to
non-zero. This silences the useless warning issued at first FTM PWM
channel configuration.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Michael Hope
