Since em starterkit has different firmware versions(2.2 and 2.3),
but the EM7D of 2.3 has new secureshield feature, which is not supported
in Zephyr, but EM7D of 2.2 is a normal EM core, which can be supported,
so we add support for 2.2 EM7D.
Signed-off-by: Huaqi Fang <huaqi.fang@synopsys.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Historically, stacks were just character buffers and could be treated
as such if the user wanted to look inside the stack data, and also
declared as an array of the desired stack size.
This is no longer the case. Certain architectures will create a memory
region much larger to account for MPU/MMU guard pages. Unfortunately,
the kernel interfaces treat both the declared stack, and the valid
stack buffer within it as the same char * data type, even though these
absolutely cannot be used interchangeably.
We introduce an opaque k_thread_stack_t which gets instantiated by
K_THREAD_STACK_DECLARE(), this is no longer treated by the compiler
as a character pointer, even though it really is.
To access the real stack buffer within, the result of
K_THREAD_STACK_BUFFER() can be used, which will return a char * type.
This should catch a bunch of programming mistakes at build time:
- Declaring a character array outside of K_THREAD_STACK_DECLARE() and
passing it to K_THREAD_CREATE
- Directly examining the stack created by K_THREAD_STACK_DECLARE()
which is not actually the memory desired and may trigger a CPU
exception
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The .balign directives were not working correctly in their
previous positions as the directive was applying to the section
before the variable's section, causing in some builds the
variables to be misaligned, and accesses to them causing faults.
With the alignments after the section declaration, the variables
will now be aligned as specified. Any future variable declarations
should use this form instead to ensure proper alignment.
Signed-off-by: Michael R Rosen <michael.r.rosen@intel.com>
Here are the main changes:
* board: Update EMSK onboard resources such as Button, Switch and LEDs
+ update soc.h for em7d, em9d, em11d
+ update board.h for em_starterkit board
* arc: Add floating point support and code density support
+ add kconfig configuration
+ add compiler options
+ add register definitions, marcos, assembly codes
+ fixes in existing codes and configurations.
* arc: Update detailed board configurations for cores of emsk 2.3
* script: Provide arc_debugger.sh for debugging em_starterkit board
+ make BOARD=em_starterkit debug
This will start openocd server for emsk, and arc gdb will connect
to this debug server, user can run `continue` command if user just
want to run the application, or other commands if debugging needed.
+ make BOARD=em_starterkit debugserver
This will start an openocd debugger server for emsk, and user can
connect to this debugserver using arc gdb and do what they want to.
+ make BOARD=em_starterkit flash
This will download the zephyr application elf file to emsk,
and run it.
Signed-off-by: Huaqi Fang <huaqi.fang@synopsys.com>
- There's no clear need to disable frame pointers if this feature is
used, remove this directive.
- The 'top' and 'base' terms are reversed. The 'base' is the high
address of the stack. The top is the lowest address, where we cannot
push further down. Fixup member and offset names to correspond to how
these terms are used in hardware documentation.
- Use correct pointers for stack top location
- Fatal exceptions now go through _NanoFatalErrorHandler to report the
faulting ip and thread.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Unline k_thread_spawn(), the struct k_thread can live anywhere and not
in the thread's stack region. This will be useful for memory protection
scenarios where private kernel structures for a thread are not
accessible by that thread, or we want to allow the thread to use all the
stack space we gave it.
This requires a change to the internal _new_thread() API as we need to
provide a separate pointer for the k_thread.
By default, we still create internal threads with the k_thread in stack
memory. Forthcoming patches will change this, but we first need to make
it easier to define k_thread memory of variable size depending on
whether we need to store coprocessor state or not.
Change-Id: I533bbcf317833ba67a771b356b6bbc6596bf60f5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Adds event based scheduling logic to the kernel. Updates
management of timeouts, timers, idling etc. based on
time tracked at events rather than periodic ticks. Provides
interfaces for timers to announce and get next timer expiry
based on kernel scheduling decisions involving time slicing
of threads, timeouts and idling. Uses wall time units instead
of ticks in all scheduling activities.
The implementation involves changes in the following areas
1. Management of time in wall units like ms/us instead of ticks
The existing implementation already had an option to configure
number of ticks in a second. The new implementation builds on
top of that feature and provides option to set the size of the
scheduling granurality to mili seconds or micro seconds. This
allows most of the current implementation to be reused. Due to
this re-use and co-existence with tick based kernel, the names
of variables may contain the word "tick". However, in the
tickless kernel implementation, it represents the currently
configured time unit, which would be be mili seconds or
micro seconds. The APIs that take time as a parameter are not
impacted and they continue to pass time in mili seconds.
2. Timers would not be programmed in periodic mode
generating ticks. Instead they would be programmed in one
shot mode to generate events at the time the kernel scheduler
needs to gain control for its scheduling activities like
timers, timeouts, time slicing, idling etc.
3. The scheduler provides interfaces that the timer drivers
use to announce elapsed time and get the next time the scheduler
needs a timer event. It is possible that the scheduler may not
need another timer event, in which case the system would wait
for a non-timer event to wake it up if it is idling.
4. New APIs are defined to be implemented by timer drivers. Also
they need to handler timer events differently. These changes
have been done in the HPET timer driver. In future other timers
that support tickles kernel should implement these APIs as well.
These APIs are to re-program the timer, update and announce
elapsed time.
5. Philosopher and timer_api applications have been enabled to
test tickless kernel. Separate configuration files are created
which define the necessary CONFIG flags. Run these apps using
following command
make pristine && make BOARD=qemu_x86 CONF_FILE=prj_tickless.conf qemu
Jira: ZEP-339 ZEP-1946 ZEP-948
Change-Id: I7d950c31bf1ff929a9066fad42c2f0559a2e5983
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Future tickless kernel patches would be inserting some
code before call to Swap. To enable this it will create
a mcro named as the current _Swap which would call first
the tickless kernel code and then call the real __swap()
Jira: ZEP-339
Change-Id: Id778bfcee4f88982c958fcf22d7f04deb4bd572f
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Historically, space for struct k_thread was always carved out of the
thread's stack region. However, we want more control on where this data
will reside; in memory protection scenarios the stack may only be used
for actual stack data and nothing else.
On some platforms (particularly ARM), including kernel_arch_data.h from
the toplevel kernel.h exposes intractable circular dependency issues.
We create a new per-arch header "kernel_arch_thread.h" with very limited
scope; it only defines the three data structures necessary to instantiate
the arch-specific bits of a struct k_thread.
Change-Id: I3a55b4ed4270512e58cf671f327bb033ad7f4a4f
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Unlike assertions, these APIs are active at all times. The kernel will
treat these errors in the same way as fatal CPU exceptions. Ultimately,
the policy of what to do with these errors is implemented in
_SysFatalErrorHandler.
If the archtecture supports it, a real CPU exception can be triggered
which will provide a complete register dump and PC value when the
problem occurs. This will provide more helpful information than a fake
exception stack frame (_default_esf) passed to the arch-specific exception
handling code.
Issue: ZEP-843
Change-Id: I8f136905c05bb84772e1c5ed53b8e920d24eb6fd
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We do the same thing on all arch's right now for thread_monitor_init so
lets put it in a common place. This also should fix an issue on xtensa
when thread monitor can be enabled (reference to _nanokernel.threads).
Change-Id: If2f26c1578aa1f18565a530de4880ae7bd5a0da2
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We do a bit of the same stuff on all the arch's to setup a new thread.
So lets put that code in a common place so we unify it for everyone and
reduce some duplicated code.
Change-Id: Ic04121bfd6846aece16aa7ffd4382bdcdb6136e3
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There are a few places that we used an naked unsigned type, lets be
explicit and make it 'unsigned int'.
Change-Id: I33fcbdec4a6a1c0b1a2defb9a5844d282d02d80e
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types. This handles the remaining includes and kernel, plus
touching up various points that we skipped because of include
dependancies. We also convert the PRI printf formatters in the arch
code over to normal formatters.
Jira: ZEP-2051
Change-Id: Iecbb12601a3ee4ea936fd7ddea37788a645b08b0
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types. There are few places we dont convert over to the new
types because of compatiability with ext/HALs or for ease of transition
at this point. Fixup a few of the PRI formatters so we build with newlib.
Jira: ZEP-2051
Change-Id: I7d2d3697cad04f20aaa8f6e77228f502cd9c8286
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is a start to move away from the C99 {u}int{8,16,32,64}_t types to
Zephyr defined u{8,16,32,64}_t and s{8,16,32,64}_t. This allows Zephyr
to define the sized types in a consistent manor across all the
architectures we support and not conflict with what various compilers
and libc might do with regards to the C99 types.
We introduce <zephyr/types.h> as part of this and have it include
<stdint.h> for now until we transition all the code away from the C99
types.
We go with u{8,16,32,64}_t and s{8,16,32,64}_t as there are some
existing variables defined u8 & u16 as well as to be consistent with
Zephyr naming conventions.
Jira: ZEP-2051
Change-Id: I451fed0623b029d65866622e478225dfab2c0ca8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix doxygen comment typos used to generate API docs
Change-Id: I94df2e3a2bda248824ed2aeff3dd0eb743f0bf3e
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
CONFIG_* usually come from Kconfig, rename variables that are locally
defined to avoid confusion about where they are set.
Change-Id: I83b8459913c5deb68dc1b9f5386b8934363a6d1f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
I2C_CLOCK_SPEED Kconfig option is DW driver specific. It does not
define I2C interface speed but rather the I2C DW module clock speed.
It is confusing for a user of any other I2C driver than DW.
This patch renames this option to I2C_DW_CLOCK_SPEED and makes it
visible only for DW I2C driver.
Change-Id: I97f57332fd5cca644eabdef0968a0b2174b885ff
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Fix c6e27a05 was too aggressive. It turns out that bluetooth on the
Quark SE boards won't enable it's own UART, because it had always been
enabled. Apps that don't do it already will be broken.
Enable UART_QMSI_0 whenever BLUETOOTH_H4 is pulled in on this
platform.
Change-Id: I5e21c6004714adba8fb0fafa056dc2d62698a3d1
Issue: ZEP-1788
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The defconfigs would always create a device for UART 0, which is
problematic in circumstances where both the x86 and ARC cores are
alive and one wants to use it in a non-default configuration.
Specifically: on Arduino 101 this is the bluetooth device and it
operates at 1MBps instead of of 115200kbps. If an x86 app sets this
up correctly, but then starts the ARC core running an app which
doesn't reference this UART at all, the device will still exist and
set up the (wrong!) configuration, clobbering the correct settings.
Just remove the "def-bool y" bits from the defconfig. There's no
need, users of these devices (e.g. the console) will enable them
anyway. There's no value to compiling it in without a configured
user.
Issue: ZEP-1677
Change-Id: I4a0e944f23705495433e9f3d0459065f131579cb
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This implementation of _tsc_read returns a 64-bit value that
is derived from the 64-bit tick count multiplied by hwcycles per tick,
and then it adds the current value from the 32-bit timer.
This produces a 64-bit time. There is a bunch of math here, which
could be avoided if the CPU is built with Real-Time-Clock option.
EM Starter Kit SOCs don't have this. I don't think Arduino 101 does
either.
See ZEP-1559
Change-Id: I9f846d170246556ac40fe2f45809e457c6375d8c
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
This commit removes the local implementation of enter_arc_state, where
the ARC is instructed to sleep, using instead the QMSI 1.4 functions.
Change-Id: Id489ad53851be50fc5e50add698891fcfaef3abe
Signed-off-by: Juan Solano <juanx.solano.menacho@intel.com>
This flag is no longer necessary and TICKLESS_IDLE will be
enabled by default if SYS_POWER_MANAGEMENT is enabled.
Jira: ZEP-1325
Change-Id: Ic6cd4b8dc0a17c6a413cabf6509b215a4558318d
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Update the builtin QMSI code to 1.4 (RC2).
The below shim drivers were updated for API or interface changes:
- aio
- counter
- i2c_ss
- rtc
- wdt.
Also, arch soc specific power management code were updated.
Jira: ZEP-1572
Change-Id: Ibc8fae032a39ffb2c2c997f697835bc0208fd308
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Kuo-Lang Tseng <kuo-lang.tseng@intel.com>
Rename devices. For example, the two i2c devices in the
quark se sensor sub-system will have name string "I2C_0"
and "I2C_1", while the other two i2c devices accessible to
both x86 and arc will have name string "I2C_2" and "I2C_3".
This is valid only when you build arc binary.
It does not apply if you build x86 or arm binary. Similar change is
also made for GPIO and SPI.
Jira: ZEP-1588 ZEP-1614
Change-Id: Ibad4486e70e0aaf287763514a5a9d28b43bca094
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This patch changes Quark SE power drivers to support multicore scenarios
e.g. both LMT and ARC core are enabled and manage power.
Handling LPS states in multicore scenarios are dead simple because LPS
states are core-specific states. It means that putting the LMT core in
LPS doesn't affect the ARC core, and vice-versa. DEEP_SLEEP state, on
the other hand, affects both cores since it turns power off from the SoC
and both cores are shutdown. It means that if LMT puts the system in
DEEP_SLEEP, ARC core is shutdown even if it is busy handling some task.
In order to support the multicore scenario, this patch introduces the
SYS_POWER_STATE_DEEP_SLEEP_2 state to both ARC and x86 power drivers.
On ARC, this state works as following:
1) Save ARC execution context;
2) Raise a flag to inform the x86 core that ARC is ready to enter in
DEEP_SLEEP;
3) Enter in the lowest core-specific power state, which in this case is
LPSS.
On x86, DEEP_SLEEP_2 is very similar to DEEP_SLEEP. The difference relies
in the post_ops() which calls _arc_init() in order to start ARC core so
it can restore its context.
This patch also adds the test/power/multicore/ directory which provides
sample application to x86 and ARC cores in order to easily verify the
multicore support. In test/power/multicore/README.rst you can find more
details regarding the applications.
Jira: ZEP-1103
Change-Id: Ie28ba6d193ea0e58fca69d38f8d3c38ca259a9ef
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
This avoids asm files from having to explicitly define the _ASMLANGUAGE
symbol themselves.
Change-Id: I71f5a169f75d7443a58a0365a41c55b20dae3029
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
They are not part of the API, so rename from K_<state> to
_THREAD_<state>.
Change-Id: Iaebb7d3083b80b9769bee5616e0f96ed2abc5c56
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Force-align all variables defined via asm .word to ensure 4-byte
alignment.
The straddled_tick_on_idle_enter variable was a bool, which resolved in
an one-byte quantity. Changing it to a 32-bit integer. It would have
occupied 4 bytes anyway with alignment.
Fixes ZEP-1549.
Change-Id: If5e0aa1a75dbc73d896b44616f059d221fe191c6
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
I've moved the call for icache_setup from nanoArchInit() to
_PrepC(), because there is a lot of code executed now before
nanoArchInit() is called, and all this time the i-cache would
be off. It should be turned on as early as possible to make
initialization faster.
Change-Id: I76a809d57a1bf9aacf51e7bb9fe8c8425f37aa13
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
These two fields in the thread structure control the preemptibility of a
thread.
sched_locked is decremented when the scheduler gets locked, which means
that the scheduler is locked for values 0xff to 0x01, since it can be
locked recursively. A thread is coop if its priority is negative, thus
if the prio field value is 0x80 to 0xff when looked at as an unsigned
value.
By putting them end-to-end, this means that a thread is non-preemptible
if the bundled value is greater than or equal to 0x0080. This is the
only thing the interrupt exit code has to check to decide to try a
reschedule or not.
Change-Id: I902d36c14859d0d7a951a6aa1bea164613821aca
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Some thread fields were 32-bit wide, when they are not even close to
using that full range of values. They are instead changed to 8-bit fields.
- prio can fit in one byte, limiting the priorities range to -128 to 127
- recursive scheduler locking can be limited to 255; a rollover results
most probably from a logic error
- flags are split into execution flags and thread states; 8 bits is
enough for each of them currently, with at worst two states and four
flags to spare (on x86, on other archs, there are six flags to spare)
Doing this saves 8 bytes per stack. It also sets up an incoming
enhancement when checking if the current thread is preemptible on
interrupt exit.
Change-Id: Ieb5321a5b99f99173b0605dd4a193c3bc7ddabf4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This will allow for an enhancement when checking if the thread is
preemptible when exiting an interrupt.
Change-Id: If93ccd1916eacb5e02a4d15b259fb74f9800d6f4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
GCC 6.x for ARC does not recognize the options
-mARCv2EM and -mav2em anymore.
Both options replaced in Makefile by -mcpu=quarkse_em.
Change-Id: I9dec26dd64b4738976704a39455fe4241406db9e
Signed-off-by: Juro Bystricky <juro.bystricky@intel.com>
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
GCC 6.x for ARC does not recognize the options
-mARCv2EM and -mav2em anymore.
Both options replaced in Makefile by -mcpu=arcem.
Change-Id: Ic86bf51cd5fb1a67ba2cd75998cd907e26996347
Signed-off-by: Juro Bystricky <juro.bystricky@intel.com>
This option has side effects. It also tells the compiler not to generate
these checks in the first place. The checks call abort() which doesn't
exist in our environment.
This patch gets rid of linker errors due to missing abort() in the 0.9 SDK.
Change-Id: Ibc5aeb5458d0bded714c9c074cdf08112733428b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
replace include <nanokernel.h> with <kernel.h> everywhere and also fix
any remaining mentions of nanokernel.
Keep the legacy samples/tests as is.
Change-Id: Iac48447bd191e83f21a719c69dc26233216d08dc
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable arc to access the i2c controller on I/O fabric.
There are two i2c controllers on quark se SoC. One is attached
to the I/O fabric and the other one is in the sensor system.
X86 cpu is only able to access the i2c controller on the I/O
fabric and the access is supported by existing code. HW allows
arc to access both controllers. But, the existing code only
gives arc access to the controller in the sensor sub-system.
Let's grant arc the access to the controller on I/O fabric as
well by the following changes.
1. Add i2c_qmsi.c into arc compilation.
2. Use the already defined macros to choose interrupt numbers
and do interrupt unmasking automatically based on the
compilation targets.
3. Add new symbols in Kconfig including driver names for both
controllers
Jira: ZEP-1189
Change-Id: I317da6038c50e0c8bd16f446182c1f8bdf6d3ba2
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
Enable arc to access the spi controller on I/O fabric.
There are two spi controllers on quark se SoC. One is attached
to the I/O fabric and the other one is in the sensor system.
X86 cpu is only able to access the spi controller on the I/O
fabric and the access is supported by existing code. HW allows
arc to access both controllers. But, the existing code only
gives arc access to the controller in the sensor sub-system.
Let's grant arc the access to the controller on I/O fabric as
well by the following changes.
1. Add spi_qmsi.c into arc compilation.
2. Use the already defined macros to choose interrupt numbers
and do interrupt unmasking automatically based on the
compilation targets.
3. Add new symbols in Kconfig including driver names for both
controllers
Jira: ZEP-1190
Change-Id: I40a5d423d4b7986a897834d1a3831938005eda6f
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
HW allows both arc and x86 to access the pwm attached to the
quark soc I/O fabric. The existing code only allows x86 to
do this. Let's give arc the access.
Change-Id: Ie88649fea41bf86b84876c260f97dd4c12fd0b81
Signed-off-by: Baohong liu <baohong.liu@intel.com>
Obsolete, replaced by _set_thread_return_value().
Change-Id: I23e9cfc07e43542f0965817edc3552d456fd2ef3
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Also remove mentions of unified kernel in various places in the kernel,
samples and documentation.
Change-Id: Ice43bc73badbe7e14bae40fd6f2a302f6528a77d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
rename NANOKERNEL_TICKLESS_IDLE_SUPPORTED to
TICKLESS_IDLE_SUPPORTED and remove nanokernel occurances in Kconfig
files.
Make TICKLESS_IDLE depend on hardware that supports it.
Change-Id: I6a2e4fb0f7cf4b45475b48e71823ea089ee98759
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Also remove some old cflags referencing directories that do not exist
anymore.
Also replace references to legacy APIs in doxygen documentation of
various functions.
Change-Id: I8fce3d1fe0f4defc44e6eb0ae09a4863e33a39db
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
And also remove now obsolete ARCH_HAS_TASK_ABORT.
ARC does not need the options either.
Change-Id: Ie52d63178a367ce12b911dacfe2d389f4f75ed2d
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
- does not pull in printk(), for potential footprint gain
- does not pull in k_thread_abort(), for single-threaded systems
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Change-Id: Ibc6a198b81a6cd73117d1e85aa05b92a4501a34d
Some kernel operations, like scheduler locking can be optmized out,
since coop threads lock the scheduler by their very nature. Also, the
interrupt exit path for all architecture does not have to do any
rescheduling, again by the nature of non-preemptible threads.
Change-Id: I270e926df3ce46e11d77270330f2f4b463971763
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
nano_cpu_idle/nano_cpu_atomic_idle were not ported to the unified
kernel, and only the old APIs were available. There was no real impact
since, in the unified kernel, only the idle thread should really be
doing power management. However, with a single-threaded kernel, these
functions can be useful again.
The kernel internals now make use of these APIs instead of the legacy
ones.
Change-Id: Ie8a6396ba378d3ddda27b8dd32fa4711bf53eb36
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The way the ready thread cache was implemented caused it to not always
be "hot", i.e. there could be some misses, which happened when the
cached thread was taken out of the ready queue. When that happened, it
was not replaced immediately, since doing so could mean that the
replacement might not run because the flow could be interrupted and
another thread could take its place. This was the more conservative
approach that insured that moving a thread to the cache would never be
wasted.
However, this caused two problems:
1. The cache could not be refilled until another thread context-switched
in, since there was no thread in the cache to compare priorities
against.
2. Interrupt exit code would always have to call into C to find what
thread to run when the current thread was not coop and did not have the
scheduler locked. Furthermore, it was possible for this code path to
encounter a cold cache and then it had to find out what thread to run
the long way.
To fix this, filling the cache is now more aggressive, i.e. the next
thread to put in the cache is found even in the case the current cached
thread is context-switched out. This ensures the interrupt exit code is
much faster on the slow path. In addition, since finding the next thread
to run is now always "get it from the cache", which is a simple fetch
from memory (_kernel.ready_q.cache), there is no need to call the more
complex C code.
On the ARM FRDM K64F board, this improvement is seen:
Before:
1- Measure time to switch from ISR back to interrupted task
switching time is 215 tcs = 1791 nsec
2- Measure time from ISR to executing a different task (rescheduled)
switch time is 315 tcs = 2625 nsec
After:
1- Measure time to switch from ISR back to interrupted task
switching time is 130 tcs = 1083 nsec
2- Measure time from ISR to executing a different task (rescheduled)
switch time is 225 tcs = 1875 nsec
These are the most dramatic improvements, but most of the numbers
generated by the latency_measure test are improved.
Fixes ZEP-1401.
Change-Id: I2eaac147048b1ec71a93bd0a285e743a39533973
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
When going into DEEP_SLEEP mode, the ARC core now saves
its context. This includes:
- All core registers
- Stack pointer
- Program counter (restored by jumping to the restore code)
The arc reset code now checks if the GPS0 bit 2 is set.
This is similar to the behavior of the x86 core done by
the QMSI bootloader which is setting GPS0 bit 1 in order
to call the restore path instead of cold boot path.
The sample has been adapted in order to support the ARC.
Jira: ZEP-1222
Change-Id: I375f03b16b8a5fd1f07ead55cf7e4947d6290c9f
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
In order to resume the ARC from deep sleep,
the interrupts need to be restored.
The FIRQ stack needs to be saved and restored
when performing sleep operations.
During early initialization, the sp in the 2nd register bank
is made to refer to _firq_stack.
This allows for the FIRQ handler to use its own stack.
Fast Interrupts cannot be used after sleep if this information
is not restored.
This patch adds the suspend and resume functions.
Jira: ZEP-1223
Change-Id: Ic81980f05aee6c1f7b8c46c743f2648c65b29486
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Move interrupt initialization for the ARC to its own
device. The init function for the arc will be only
doing platform specific operations
Jira: ZEP-1288
Change-Id: Icb04c3622890021c65cd24cecf6cafee6c37caf9
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
As flags are modified when entering sleep, add cc to
clobber list.
Jira: ZEP-1408
Change-Id: Ia80bc1c7ddedb9d9963c47108372a90928597c1d
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
Memory access could be reorderd around sleep. Add memory
in clobber list.
Jira: ZEP-1408
Change-Id: I49df2542e0059ba76a262fbda58eb46b86e89bea
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
A build error was resulting if CONFIG_ARC_STACK_CHECKING is enabled.
There is a breq that was too far. Adding conditional code to
re-arrange the branching so that it can be done.
See ZEP-1116.
Change-Id: Idea85817b2e05617bbaa4450437aa74c5737e213
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Zephyr is always setting irqs to be level triggered as
required by the core. It is unnecessary to set it to
level again while entering sleep states.
Change-Id: I10f919d619af2e1ab05dc85a67766929b6ae9402
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Too much code might run with a stale icache, before _PrepC(), so move
the invalidation/disabling code earlier. The asm code does the exact
same thing disable_icache() and invalidate_dcache() were doing.
Change-Id: If52f4e4a1de546fb82873c91ead95614a44b106d
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
When sleep instruction is called with interrupts enabled, the
interrupt priority threshold bits need to be set. Only interrupts
with equal or higher priority will wake the sleep. Currently it
is set to 0 unintentionally and only priority 0 interrupt can
wake the sleep.
Jira: ZEP-1349
Change-Id: I927e259345cc37c5ecc4dfdcde996dd16443e61b
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
There is no FIRQ stack in the system in this case, so do not initialize
it.
Change-Id: I8bc068ce43ac8a39909994d8cc01ba0c6a17f4ae
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Also remove NO_METRIC, which is not referenced anywhere anymore.
Change-Id: Ieaedf075af070a13aa3d975fee9b6b332203bfec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Move _thread_base initialization to _init_thread_base(), remove mention
of "nano" in timeouts init and move timeout init to _init_thread_base().
Initialize all base fields via the _init_thread_base in semaphore groups
code.
Change-Id: I05b70b06261f4776bda6d67f358190428d4a954a
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Use the main stack during very early boot so that we can call memset on
the interrupt and FIRQ stacks. Iniitalize the them before one of them is
used for the rest of the pre-kernel initialization.
Change-Id: Ib57856a66273dda9382e08fa91da5a54847b77c2
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Same issue as with ARM. ARC can use _Swap() though, because the call to
it is serial, not generating a low-priority exception and interrupts are
locked until the main() thread is context-switched into and the
interrupt stack is released.
Fixes ZEP-1310.
Change-Id: Ie1f27f7ad0502191ca2867b5400d6e0bfb7f0fc6
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Artifact from microkernel, for handling multiple pending tasks on
nanokernel objects.
Change-Id: I3c2959ea2b87f568736384e6534ce8e275f1098f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Prio should be an int, since values are small integers, not a fixed-size
int32_t. It aligns with the prio parameters of the other APIs.
Stack size should be size_t.
Change-Id: Id29751b86c4ad7a7c2a7ffe446c2a96ae83c77bf
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
When a thread dies, at least print the pointer to it, so we can debug
better.
Change-Id: Ief6bbc0c221e2d5271c240a4b73df16413aa5e22
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
There was a lot of duplication between architectures for the definition
of threads and the "nanokernel" guts. These have been consolidated.
Now, a common file kernel/unified/include/kernel_structs.h holds the
common definitions. Architectures provide two files to complement it:
kernel_arch_data.h and kernel_arch_func.h. The first one contains at
least the struct _thread_arch and struct _kernel_arch data structures,
as well as the struct _callee_saved and struct _caller_saved register
layouts. The second file contains anything that needs what is provided
by the common stuff in kernel_structs.h. Those two files are only meant
to be included in kernel_structs.h in very specific locations.
The thread data structure has been separated into three major parts:
common struct _thread_base and struct k_thread, and arch-specific struct
_thread_arch. The first and third ones are included in the second.
The struct s_NANO data structure has been split into two: common struct
_kernel and arch-specific struct _kernel_arch. The latter is included in
the former.
Offsets files have also changed: nano_offsets.h has been renamed
kernel_offsets.h and is still included by the arch-specific offsets.c.
Also, since the thread and kernel data structures are now made of
sub-structures, offsets have to be added to make up the full offset.
Some of these additions have been consolidated in shorter symbols,
available from kernel/unified/include/offsets_short.h, which includes an
arch-specific offsets_arch_short.h. Most of the code include
offsets_short.h now instead of offsets.h.
Change-Id: I084645cb7e6db8db69aeaaf162963fe157045d5a
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Regardless of the number of interrupt priorities
supported, the exit of the trap handler can check
AUX_IRQ_ACT to see if it interrupted a FIRQ or IRQ.
Change-Id: I0b84d8298d3e6e437c934c01db4535fa8fe29458
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Add Low Power States support to the power shim layer
and show the usage in the quark_se sample.
States are defined as follow:
- SYS_POWER_STATE_CPU_LPS: SS2 with LPSS enabled
- SYS_POWER_STATE_CPU_LPS_1: SS2 with LPSS disabled
- SYS_POWER_STATE_CPU_LPS_2: SS1 with LPSS disabled
Jira: ZEP-994
Change-Id: Ie4b93f6e539cb53fc035be00280b66b2cb0d9fea
Signed-off-by: Julien Delayen <julien.delayen@intel.com>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Verify the thread priorities are within the bounds when starting a new
thread and when changing the priority of a thread.
Change-Id: I007b3b249e4b80235b6439cbee44cad2f31973bb
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
A race condition would happend if a FIRQ interrupted a
return-from-interrupt from a RIRQ at the wrong moment: if a decision was
already taken which thread to context switch in and the FIRQ woke up
another thread of higher priority, the ready queue would be corrupted.
The solution is to lock interrupts at the moment the interrupt return
code starts looking at the kernel queues. Interrupts do not need to be
unlocked before exiting: the return-from-interrupt (rtie) instruction
will restore the correct interrupt locking state for the thread being
context switched in.
Change-Id: I777665c2faeca7b1f2a77ddd9ee2a520080bae88
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
An implementation to flush multiple d-cache lines has been added
per the top-level cache.h API. ZEP-1153 was opened to express
the need for MORE i-cache and d-cache APIs. For example, the current
cache.h API doesn't provide a means to invalidate d-cache lines
and has nothing for i-cache.
I've also modified some of the i-cache related aux registers to have
better names so that they won't be confused with d-cache.
These changes are for
ZEP-1176.
Change-Id: If4c5410451cc40dcd5618fc871093c8febf7e061
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Symbols now use the K_ prefix which is now standard for the
unified kernel. Legacy support for these symbols is retained
to allow existing applications to build successfully.
Change-Id: I3ff12c96f729b535eecc940502892cbaa52526b6
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Adds standard prefix to symbolic option that flags a thread
as essential to system operation.
Change-Id: Ia904a81ce343fdd1cd44caaaeae641d822777f9b
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
