Following activation of Cube LL based clock control driver,
this commits cleans up the useless structures for RCC definitions
and remove code relative to native L4 Clock control driver.
Change-Id: Ic0408d5f5ec66651d46d13dfaf447da2666367cd
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introduction of STM32Cube based clock control driver for
stm32 family, provide its support on stm32f3x soc.
Clean up will have to be done afterwards.
Change-Id: I20480579f12a6fc1f1f6a51589981ac3f1d63ef0
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
After introduction of STM32Cube based clock control driver for
stm32 family, provide its support on stm32l4x soc.
Clean up will have to be done afterwards.
Change-Id: I979a4169148c5fe5a0693d182d2d17f9ffaf1c77
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds the base DTS support for the KW41Z Freedom board. The
initial set of changes include SRAM, FLASH, IRQ controller and LPUART
support.
Change-Id: Ic68c4959ddad0c5cfe70d5576a0e58372b93ec9d
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
This patch adds DTS support to the ARM CMSDK UART driver. The DTS
currently specifies the IRQ, IRQ PRIO, and base address of the port.
Change-Id: I8e5bc81c013958be4297d563495bf126b53a83a9
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the base DTS support for the V2M Beetle board. The
initial set of changes include SRAM, FLASH, and IRQ controller support.
Change-Id: I06685622b9c57ac358544c71350074ce06e3371e
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds all the necessary changes to enable use of DTS for
generating required build information.
Change-Id: Ia476fbb14c7d9d6b9db3340c73f599556a880da3
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch ifdef's out information that would be redefined by
information generated from DTS. This patch also fixes up the serial
drives to work properly with the DTS generated information.
Change-Id: I912ccf35be23c107705a4866e5a68b3b51154ffa
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds DTS support and related files for the NXP Kinetis
platform. The DTS files contain the base definitions for the hardware
nodes on Kinetis platforms. The YAML files provide the definitions of
the contents of the DTS nodes.
The Kconfig changes were put in place to allow for the conversion of
existing drivers. Once those drivers are modified, the Kconfig options
that are replaced by the DTS information will be removed.
Change-Id: If110fffa99c0b12471cf2df206da6687277e4756
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support for using device tree configuration files for
configuring ARM platforms.
In this patch, only the FLASH_SIZE, SRAM_SIZE, NUM_IRQS, and
NUM_IRQ_PRIO_BITS were removed from the Kconfig options. A minimal set
of options were removed so that it would be easier to work through the
plumbing of the build system.
It should be noted that the host system must provide access to the
device tree compiler (DTC). The DTC can usually be installed on host
systems through distribution packages or by downloading and compiling
from https://git.kernel.org/pub/scm/utils/dtc/dtc.git
This patch also requires the Python yaml package.
This change implements parts of each of the following Jira:
ZEP-1304
ZEP-1305
ZEP-1306
ZEP-1307
ZEP-1589
Change-Id: If1403801e19d9d85031401b55308935dadf8c9d8
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The entry point specified in the elf file should always point to
executable code, and not to the interrupt vector table. Pointing to the
vector table as the entry point in the elf file presents problems with
running the kernel against a debugger as the debugger starts the program
counter at the top of the interrupt vector table.
Change-Id: I76051f6e99a44bab72936670bead5fb8191a6ec7
Signed-off-by: Tim Nordell <tim.nordell@nimbelink.com>
This is a zero-copy networking implementation of Ethernet driver.
Limitations:
- one shot PHY setup, no support for PHY disconnect/reconnect
- no support for devices with DCache enabled due to missing
non-cacheable RAM regions in Zephyr.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-1492
Change-Id: Ib944f91193efbd12c1142b0bcf1f635388bf1b87
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added basic USART driver for Atmel SAM MCU family. USART is a very
comprehensive module, currently only basic features sufficient to
support printf functionality are implemented by this driver.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Ia9710e4069243fb6c30de45953dfc1fe1266b63a
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
Added common, internal, always available SAM HAL drivers: pmc, gpio.
Note: these drivers are meant to be used by other SAM drivers, not by
a user space program directly.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: I00cca358f27790dc94cf79f840584b85ff5191f6
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
Added support for early SoC configuration which does not belong
conceptually to system initialization. ERASE, JTAG TDI pins are
currently configured here.
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Id51adddb4c7cce22907af214461d75db83df129a
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added support for Atmel SAM E70 (Cortex-M7) MCU:
- Kconfig files
- device start-up code
Tested on Atmel SMART SAM E70 Xplained board
Origin: Original
Jira: ZEP-978
Change-Id: Ide4fd5dadd94897303090a6507b8d048773b645e
Signed-off-by: Piotr Mienkowski <Piotr.Mienkowski@schmid-telecom.ch>
As cpu_idle.S is the only bit of code that is using the SCB asm defines,
so to allow us to remove scb.h in the future lets move the defines that
are used just into cpu_idle.S
Jira: ZEP-1568
Change-Id: I3c3a6f145ec4c1a43f076d079d5fe1694c255b78
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A number of SoCs clear out the Mem/Bus/Usage and Hard Fault exceptions
during init. Lets refactor that into a common function so we don't have
to keep duplicating it over and over.
Change-Id: Ida908a9092db37447abcf3c9872f36937982f729
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch fixes the UART4 base address on the ARM MPS2 platform.
Change-Id: I14bf2a4dc2378d4b2c4295a75cd68c6c895fbd60
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Kill of nvic.h and use either CMSIS helper functions for NVIC or direct
NVIC register access via CMSIS for IRQ handling code.
Jira: ZEP-1568
Change-Id: If21910b9293121efe85c3c9076a1c2b475ef91ef
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace _ScbExcPrioSet with calls to NVIC_SetPriority as it handles both
interrupt and exception priorities. We don't need to shift around the
priority values for NVIC_SetPriority.
Jira: ZEP-1568
Change-Id: Iccd68733c3f7faa82b7ccb17200eef328090b6da
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds the configuration parametes required to enable CMSDK
(Cortex-M System Design Kit) Drivers at MPS2 soc level.
It provides as well the definitions for the MPS2 System Control
registers.
Change-Id: I06181dcfeb4fb887425b85ec9a99c268c857a34e
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Adds initial support for the kw41z SoC. This is the first SoC in the
Kinetis W (wireless connectivity) series added to Zephyr. The kw41z
integrates a 2.4 GHz radio transceiver, BLE link layer hardware, and an
802.15.4 packet processor with an ARM Cortex M0+. It has 512 KB flash,
128 KB SRAM, and can run the system clock at up to 48 MHz.
This SoC currently has mcux shim drivers for lpuart (serial), gpio,
pinmux, i2c, and flash.
Jira: ZEP-1389
Change-Id: I8cff6d203867ba3ace7e05c36441dc8f3cbca8d8
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Renames the flash security section so it makes sense for other Kinetis
devices, not just k64. In Kinetis reference manuals, this section is
referred to as the 'flash configuration field'.
Change-Id: I2b7c7cc1ec2541419d77878d367d96c9ceb7a0cf
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux lpuart driver to adapt it to the Zephyr
serial interface.
NXP has multiple uart hardware blocks that implement different features
and have different register maps. The k64 has a uart block called
'uart', while the kw41 has a uart block called 'lpuart' (low power
uart). The MCUXpresso SDK provides separate drivers for each type of
uart block but with similar software interfaces. As a result, there are
also separate shim drivers in Zephyr. There is a 1:1:1 relationship
between hardware block, mcux driver, and mcux shim driver.
Because we now have two mcux shim drivers for the uart interface, a new
naming convention is created:
<interface>_mcux_<hw block>
Where <interface> is the name of the Zephyr interface, in this case
'uart'. This convention is not new.
<hw block> is the name of the NXP hardware block, in this case 'lpuart'.
This is the new part, and distinguishes different hardware blocks
for the same interface.
Change-Id: I3a80b9bffa116bbb2b02ee950d4bdd79a19a4edc
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Nordic Semiconductor's Software Development Kit's HAL layer
provides a set of low-level header and sourcefiles that give access
to the different hardware peripherals of Nordic ICs.
This patch includes the new files in the build and refactors the Kconfig
and Kbuild files in ext/hal/nordic to acommodate for the presence of the
new HAL layer.
Change-Id: Ie8e1a4c9fcc7e9058a9d16a2692ef1789603aa53
Signed-off-by: Wojciech Bober <wojciech.bober@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The STM32 GPIO driver extended the generic GPIO driver interace with
the concept of OPEN_DRAIN. There is previous discussion about
representing such concepts in the GPIO interface in a more general
fashion here:
https://lists.zephyrproject.org/archives/list/devel@lists.zephyrproject.org/thread/6DCFUAKCOOOBHUO3ZK45ES6IQXOEOFWN/
The DRIVE STRENGTH interface supports the concepts of OPEN DRAIN and
other variants supports by other vendors hardware.
Adjust the STM32 GPIO driver to use the DRIVE STRENGTH interface. A
following patch will address the simplication of gpio.h
Change-Id: I56b0792ec2b21f1adc673dff019288dc8573d005
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
This avoids asm files from having to explicitly define the _ASMLANGUAGE
symbol themselves.
Change-Id: I71f5a169f75d7443a58a0365a41c55b20dae3029
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
They are not part of the API, so rename from K_<state> to
_THREAD_<state>.
Change-Id: Iaebb7d3083b80b9769bee5616e0f96ed2abc5c56
Signed-off-by: Benjamin Walsh <walsh.benj@gmail.com>
Replace _scs_relocate_vector_table with direct CMSIS register access and
use of __ISB/__DSB routinues. We also cleanup the code a little bit to
just have one implentation of relocate_vector_table() on ARMv7-M.
Jira: ZEP-1568
Change-Id: I088c30e680a7ba198c1527a5822114b70f10c510
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
CMSIS provides a complete implentation for reboot, we can utilize it
directly and reduce zephyr specific code.
Jira: ZEP-1568
Change-Id: Ia9d1abd5c1e02e724423b94867ea452bc806ef79
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As a first step towards removing the custom ARM Cortex-M Core code
present in Zephyr in benefit of using CMSIS, this change replaces
the use of the custom core code with CMSIS macros in
enable_floating_point().
Jira: ZEP-1568
Change-id: I544a712bf169358c826a3b2acd032c6b30b2801b
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Support using CMSIS defines and functions, we either pull the expect
defines/enum from the SoC HAL layers via <soc.h> for the SoC or we
provide a default set based on __NVIC_PRIO_BITS is defined.
We provide defaults in the case for:
IRQn_Type enum
*_REV define (set to 0)
__MPU_PRESENT define (set to 0 - no MPU)
__NVIC_PRIO_BITS define (set to CONFIG_NUM_IRQ_PRIO_BITS)
__Vendor_SysTickConfig (set to 0 - standard SysTick)
Jira: ZEP-1568
Change-Id: Ibc203de79f4697b14849b69c0e8c5c43677b5c6e
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In preperation for removing the scb/scs layers and using CMSIS directly
lets remove all the _Scb* and _Scs* functions that are not currently
used.
Jira: ZEP-1568
Change-Id: If4641fb9a6de616b4b8793d4678aaaed48e794bc
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
ARM's Cortex-M Prototyping System (or MPS2) [1] is a board containing
devices such as RAM, ethernet and display, and at its heart there is an
FPGA which can be programmed with various 'SoCs' which implement the
CPU, SRAM, UARTs, SPI, DMA, etc. There are also software simulations of
systems based on this hardware which are part of ARM's Fixed Virtual
Platforms (FVPs).
All of the above could be regarded SoCs in the same series so we will
treat them as such in Zephyr.
In this initial patch we add SoC support for the public FPGA image
which implements a Cortex-M3 CPU, and includes definitions to support
use of the UARTs on this.
ARM's documentation for MPS2 images are titled 'Application Note ANnnn'
where the number nnn is different for each 'SoC'. E.g. Application Note
AN385 is for "ARM Cortex-M3 SMM on V2M-MPS2" [2]. The files ARM supply
for programming the board firmware also make extensive use of the ANnnn
nomenclature, so we will use this for the SoC name in Zephyr. E.g. the
Cortex-M3 SoC will be called 'mps2_an385'. Note, it is not possible to
use the CPU type (e.g. M3) for the name as there are multiple FPGA
images for some CPU types (e.g. there are three Cortex M7 images
with differing FPU and MPU support).
[1] https://www.arm.com/products/tools/development-boards/versatile-express/cortex-m-prototyping-system.php
[2] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dai0385c/index.html
Change-Id: Ice54f2d2cde7669582337f256c878526139daedd
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Now that we have a more generic mcux spi driver that can be used across
multiple Kinetis SoCs, remove the specific k64 spi driver.
Jira: ZEP-1374
Change-Id: Ifc324374f305837f5e3d2cfd7ad30d3608865b5b
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds the timers IRQ map to the ARM Beetle SoC platform.
Jira: ZEP-1300
Change-Id: If38a197210f71ae90c7ee6274395f064116faf72
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
On other targets, CONFIG_TEXT_SECTION_OFFSET allows the entire image to
be moved in memory to allow space for some type of header. The Mynewt
project bootloader prepends a small header, and this config needs to be
supported for this to work.
The specific alignment requirements of the vector table are chip
specific, and generally will be a power of two larger than the size of
the vector table.
Change-Id: I631a42ff64fb8ab86bd177659f2eac5208527653
Signed-off-by: David Brown <david.brown@linaro.org>
Now that we have a more generic mcux serial driver, remove the uart_k20
driver.
Jira: ZEP-719
Change-Id: I51a3237454140feabbfe18ac2c8ee451e572c7be
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Stop using the specific uart_k20 driver by default and start using the
more generic mcux uart driver instead.
Jira: ZEP-719
Change-Id: I7b107ea7118887591362159283ebb5413b45595a
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Implementation includes adding some defines in the pinmux,
adjusting gpio driver to specific defines for STM32F3X family,
adding specific functionality in the F3X SoC definition.
Change-Id: I465c66eb93e7afb43166c4585c852e284b0d6e67
Signed-off-by: Adam Podogrocki <adam.podogrocki@rndity.com>
