At chip startup, jtag pins are configured by default to enable
debug.
This configuration adds consumption and when using PM profile,
we can save ~40uA by resetting this configuration and setting pins
to analog mode.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
The STM32G0 soc has 2 CAN controllers. The 2nd on was not working
with zephyr yet as both controllers shares the same IRQ. Recently, the
shared irq system was integrated on now, both can controllers can work
on this chip. Shared interrupts must be enabled only if both can
controllers are enabled.
Signed-off-by: Adrien MARTIN <adrienmar@kickmaker.net>
Now that:
1 - LS Clocks sources values are identical accross series
2 - We're able to extract this value from device tree
define STM32_LPTIM_CLOCK choice symbol from device tree
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Use sys_cache* functions to enable the caches for stm32f7 and
stm32h7. This ensures that CONFIG_CACHE_MANAGEMENT is
considered correctly.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
When Power Management is enabled (CONFIG_PM=y),
the CONFIG_IDLE_STACK_SIZE of 320 is not enough :
Increase its size to 512.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
The defconfig.series file for the stm32f4 incorrectly redefines
the PM Kconfig in order to select two dependencies, COUNTER and
COUNTER_RTC_STM32_SUBSECONDS, instead of setting a default for
them if PM is included.
This commit fixes the error described above.
Signed-off-by: Bjarki Arge Andreasen <bjarki@arge-andreasen.me>
Supporting Stop1 mode while BLE RF is enabled requires some specific
adaptation and usage of STM32WBA Cube BLE controller scm API.
scm (Secure clock manager) is in charge of switching clock depending
on RF status and should be informed of PM stop modes scheduling.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
STM32WBA controller uses a PKA driver to perform cyphering operations
on keys. Since PKA hardware block requires RNG clock to be enabled, a
synchronization with zephyr RNG driver is needed.
Use RNG enable status to check if RNG could be switched off or needs to
be switched on.
Similarly in entropy driver, don't cut RNG clock if PKA is enabled.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
In order to enable BLE support on STM32WBA, following APIs are implemented:
- HostStack_: BLE Controller scheduling
- ll_sys_: Link layer API required for scheduling
- UTIL_TIMER_: BLE Controller timer utility
- LINKLAYER_PLAT_: BLE controller utilities
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
The STM32F722 is similar to the STM32F723, but lacks the latter's
more advanced USB PHY. Otherwise, they are virtually identical.
Signed-off-by: Evan Perry Grove <evan@4grove.com>
The STM32 G4 series has a built-in Arm Instrumentation Trace
Macrocell. Set CONFIG_HAS_SWO to enable this.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Configure the SYS_CLOCK_TICKS_PER_SEC directly from the
DTS st-prescaler property of the lptim node
aka stm32_lp_tick_source
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The instruction cache in the STM32F7 and H7 was enabled regardless
of the value assigned via Kconfig to the CONFIG_ICACHE parameter.
This commit adds the missing conditional checks; note that this does
not affect the compiled behavior unless CONFIG_ICACHE is explicitly
disabled by the user.
Remove a redundant low-level check on DCache being already enabled,
since it is also performed inside the SCB_EnableDCache function.
Signed-off-by: Luca Burelli <l.burelli@arduino.cc>
Some SoC have missing feature selections in their Kconfig.
Some others are missing includes of CMSIS-Core headers.
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
Caches are optional on cortex-m7, having CPU_HAS_*CACHE in CPU_CORTEX_M7
definition renders them mandatory.
Signed-off-by: Wilfried Chauveau <wilfried.chauveau@arm.com>
Add soc power management for the STM32F4x chips.
One low power state is added supported by all chips from the family -
the Stop mode with voltage regulator in low-power mode.
The Stop mode for STM32F chips has to work with the IDLE timer -
CORTEX_M_SYSTICK_IDLE_TIMER, because PLL and HSI are disabled in the
Stop mode (Systick is not clocked). The only possible wakeup source is
RTC, which works as a IDLE timer for the Systick.
The exit latency may need to be adjusted per system, depending on the
system tick frequency and other variables.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
This commit updates all arm SoCs to set SOC_LINKER_SCRIPT CMake
variable to point to active linker script directly.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Force STM32_ENABLE_DEBUG_SLEEP_STOP option when running tests.
This option enables Debug in Sleep/stop states and disables it when
disabled (default state).
When disabled, it may be impossible to flash the device with runner
such as openocd. It's generally working using cubeprogrammer, but it might
fail as well with fault configuration.
Instead of fixing each test or breaking CI each time a new test is created
with CONFIG_PM=y, force this option to be enabled when ZTEST=y (as it was
already the case when DEBUG=y).
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Adds CONFIG_STM32_ENABLE_DEBUG_SLEEP_STOP to allow debugger attaching in
sleep/stop mode of STM32 parts. Mainly useful for debugging. Move DBGMCU
from part-sepcific power.c to common soc_config.c. CONFIG_USE_SEGGER_RTT
depends on this as well.
Signed-off-by: Roland Lezuo <roland.lezuo@embedded-solutions.at>
This is the final step in making the `zephyr,memory-attr` property
actually useful.
The problem with the current implementation is that `zephyr,memory-attr`
is an enum type, this is making very difficult to use that to actually
describe the memory capabilities. The solution proposed in this PR is to
use the `zephyr,memory-attr` property as an OR-ed bitmask of memory
attributes.
With the change proposed in this PR it is possible in the DeviceTree to
mark the memory regions with a bitmask of attributes by using the
`zephyr,memory-attr` property. This property and the related memory
region can then be retrieved at run-time by leveraging a provided helper
library or the usual DT helpers.
The set of general attributes that can be specified in the property are
defined and explained in
`include/zephyr/dt-bindings/memory-attr/memory-attr.h` (the list can be
extended when needed).
For example, to mark a memory region in the DeviceTree as volatile,
non-cacheable, out-of-order:
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-attr = <( DT_MEM_VOLATILE |
DT_MEM_NON_CACHEABLE |
DT_MEM_OOO )>;
};
The `zephyr,memory-attr` property can also be used to set
architecture-specific custom attributes that can be interpreted at run
time. This is leveraged, among other things, to create MPU regions out
of DeviceTree defined memory regions on ARM, for example:
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-region = "NOCACHE_REGION";
zephyr,memory-attr = <( DT_ARM_MPU(ATTR_MPU_RAM_NOCACHE) )>;
};
See `include/zephyr/dt-bindings/memory-attr/memory-attr-mpu.h` to see
how an architecture can define its own special memory attributes (in
this case ARM MPU).
The property can also be used to set custom software-specific
attributes. For example we can think of marking a memory region as
available to be used for memory allocation (not yet implemented):
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-attr = <( DT_MEM_NON_CACHEABLE |
DT_MEM_SW_ALLOCATABLE )>;
};
Or maybe we can leverage the property to specify some alignment
requirements for the region:
mem: memory@10000000 {
compatible = "mmio-sram";
reg = <0x10000000 0x1000>;
zephyr,memory-attr = <( DT_MEM_CACHEABLE |
DT_MEM_SW_ALIGN(32) )>;
};
The conventional and recommended way to deal and manage with memory
regions marked with attributes is by using the provided `mem-attr`
helper library by enabling `CONFIG_MEM_ATTR` (or by using the usual DT
helpers).
When this option is enabled the list of memory regions and their
attributes are compiled in a user-accessible array and a set of
functions is made available that can be used to query, probe and act on
regions and attributes, see `include/zephyr/mem_mgmt/mem_attr.h`
Note that the `zephyr,memory-attr` property is only a descriptive
property of the capabilities of the associated memory region, but it
does not result in any actual setting for the memory to be set. The
user, code or subsystem willing to use this information to do some work
(for example creating an MPU region out of the property) must use either
the provided `mem-attr` library or the usual DeviceTree helpers to
perform the required work / setting.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Configure SWO reference frequency to be the same as
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC. This should make all ST boards ready to
be used with SWO, without configuring any other devicetree property.
Tested with NUCLEO-L476RG and NUCLEO-H563ZI.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
This commit follows the parent commit work.
This commit introduces the following major changes.
1. Move all directories and files in 'include/zephyr/arch/arm/aarch32'
to the 'include/zephyr/arch/arm' directory.
2. Change the path string which is influenced by the changement 1.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
Implement the hook for sys_poweroff based on the SOFT_OFF code. Note
that standby mode was a substate of SOFT_OFF, however, it was not
supported judging from defined DT states. It can be added later using
the STANDBY state.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Implement the sys_poweroff() hook. The hsem locking is not part of the
implementation, it doesn't seem necessary after
https://github.com/zephyrproject-rtos/zephyr/pull/42409 but I may be
wrong. Needs verification.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
SOFT_OFF state (which translates to standby) doesn't seem to be
supported according to the L0 DT files. Also, by definition soft off
implies context loss, ie boot from scratch, but the implementation
expected a call to the PM exit hook.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
System memory declared by the MPU as 'Strongly Ordered'
with region attributes which will inhibit the speculative fetch,
preventing the Flash RDSERR.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
In case of stm32h5 both LL_DBGMCU_EnableTraceClock() and
LL_DBGMCU_SetTracePinAssignment() need to be called in order to properly
configure SWO output.
Select HAS_SWO, so that logging over SWO can be enabled.
Tested with ST's fork of openocd [1].
[1] https://github.com/STMicroelectronics/OpenOCD
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
The CMSIS module glue code was part of arch/ directory. Move it to
modules/cmsis, and provide a single entry point for it: cmsis_core.h.
This entry header will include the right CMSIS header (M or A/R).
To make this change possible, CMSIS module Kconfig/CMake are declared as
external, allowing us to add a new Zephyr include directory.
All files including CMSIS have been updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move arm_mpu_mem_cfg header to common include directory.
The benefits are two-fold:
- Allow for out of tree SoC definitions to use them to
define mpu_regions.
- Remove odd relative include path
Signed-off-by: Moritz Fischer <moritzf@google.com>
Added dts additions for stm32f105xb cpu which is the same as existing
stm32f105xc with less flash.
Signed-off-by: Mathieu Anquetin <mathieu.anquetin@groupe-cahors.com>
Remove unnecessary __weak attribute from power management functions.
These functions are now defined once, globally, and mandatory for
systems that support CONFIG_PM.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
