According to RM0041.pdf clock tree for stm32f100xx devices is
different from both STM32F10X density and connectivity lines devices,
but is a combination of both.
Rework symbols definitions so that STM32F100xx is neither of those
and uses:
- CLOCK_STM32_PLL_MULTIPLIER as on SOC_STM32F10X_DENSITY_DEVICE
- CLOCK_STM32_PLL_PREDIV1 as on SOC_STM32F10X_CONNECTIVITY_LINE_...
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move the STM32F0 specific ram vector table sections into a dedicated
linker snippet included by the new `SRAM_VECTOR_TABLE` symbol.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Add a new Kconfig symbol that explicitly controls whether the vector
table should be placed in RAM. This eliminates the side effect of
`IS_BOOTLOADER` controlling vector table location. Making the condition
a positive assertion also allows the config to be used in CMakeLists
conditions (`zephyr_linker_sources_ifdef()`, etc).
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Fixes#29915.
Implements the memory layout and MPU configuration for Ethernet buffers
for STM32H7 controllers as recommended by ST. 16 KB of SRAM3 are
are reserved for this. The first 256 B are for the RX/TX descriptors and
configured as strongly ordered, shareable memory. The rest is for RX/TX
buffers and configured as non cacheable memory. This configuration is
automatically applied for H7 chips if the SRAM3 memory is enabled in the
device tree.
Signed-off-by: Mario Jaun <mario.jaun@gmail.com>
Optionally configure Kconfig SYS_CLOCK_HW_CYCLES_PER_SEC using
clock-frequency provided by dt if sysclk node is enabled
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To allow transition to device tree based clock configuration on
stm32 targets, rework clock_control driver to use intermediate
STM32_ macros initially defined as the equivalent Kconfig macros
for now.
Propagate the change in all code using these macros.
The reason to introduce these new macros instead of configuring
Kconfig flags using dt kconfigfunctions is that we'll need
to be able to inform users that Kconfig flags are deprecated
once the whole family conversion is done, to encourage
out of tree users to adopt this new configuration scheme.
Note: For now STM32H7 series and code is excluded.
This is the same for some series specific code such as
PLL mul/div for L0/L1 and XTRE prescaler on F1 series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit adds the soc config for the STM32F031k6 and STM32F031X6.
Add the STM32F031k6 as choice to the Kconfig.soc.
Signed-off-by: Sebastian Schwabe <sebastian-schwabe@gmx.de>
Move the definition of the two IPC RAM blocks from `#define`'s in family
linker scripts to proper devicetree nodes. Use the devicetree nodes to
generate the memory regions.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
With this patch, the UCPD1 _CC1 and _CC2 pins
are disabling the USB Type-C and Power Delivery Dead Battery.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
With this patch, the UCPD1 _CC1 and _CC2 pins
are disabling the USB Type-C and Power Delivery Dead Battery.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
With this patch, the UCPD1 _CC1 and _CC2 pins
are disabling the USB Type-C and Power Delivery Dead Battery.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
soc/arm/st_stm32/CMakeLists.txt already has a
zephyr_include_directories(common) so including in again
soc/arm/st_stm32/common/CMakeLists.txt is redudant.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The low power states 0∕1∕2 are added to the stm32wb.
The substate-id is mapping the same Zephyr power state.
They correspond to the stm32wb low power stop0/1/2 modes.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The debug config will let the clocks active in STOP mode
at init.
The substate-id is mapping the same Zephyr power state.
Plus a minor fix in the Kconfig.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The low power modes are available on the stm32l5 soc
with the mcu STOP0/1/2 modes, depending on the CONFIG_PM
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The low power states 0∕1∕2 are added to the stm32l4.
The substate-id is mapping the same Zephyr power state.
They correspond to the stm32l4 low power stop0/1/2 modes.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
PWR clock is required for various operations.
It is enabled by default in clock control driver,
but disabled at clock init.
It appears soc init is run after clock control driver init
and hence PWR is disabled to to this piece of code at
soc init level.
Don't disable PWR here.
(But keep PWR clock enable in case of ...).
A whole clock clean up will be required later on,
but waiting for that to happen, this is the safest we can do.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This config CPU_CORTEX_M_HAS_DWT, is to avoid the
pragma message "Null-Pointer exception detection cannot
be configured on un-mapped flash areas"
Signed-off-by: Francois Ramu <francois.ramu@st.com>
CORTEX_M_SYSTICK should be disabled if LPTIM is selected.
Current implementation is not efficient to do so.
Rework the way the dependency is stated.
Fixes#33342
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In some stm32 series systick was disabled in order to
allow alternate use of lptim timer as kernel low power ticker.
Doing this, dts based definition of CORTEX_M_SYSTICK Kconfig symbol
is disabled and CORTEX_M_SYSTICK was redefined with 'default y'
in stm32 soc files which makes things more complex to handle to
alternate with LPTIM activation.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
New power states have more granularity than deep sleep and sleep
states. Just get rid of this and keep the same behavior for now.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
stm32wb and stm32l4 are devices which supports the low power
from the Kernel PM, so is the PM_DEVICE defined.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
In case the policy is not available or defined by th application
the pm_policy_low_power_devices is still valid
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The clock configuration is restored by the stm32_clock_control_init
function of the clock_stm32_ll_common driver
when exiting the low power mode
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Signed-off-by: Francois Ramu <francois.ramu@st.com>
In case the policy is not available or defined by th application
the pm_policy_low_power_devices is still valid
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The clock configuration is restored by the stm32_clock_control_init
function of the clock_stm32_ll_common driver
when exiting the low power mode.
Keeping the stm32wbxx_ll_utils.h in case the PLL is used for wb.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This driver missed #32228 PR that converted STM32 drivers
to use DEVICE_DT_GET for clock activation.
Due to the renaming of STM32_CLOCK_CONTROL_NAME to
STM32_CLOCK_CONTROL_NODE, driver could not compile anymore
Fix this.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When exiting Stop mode, if system clock is MSI, MSI oscillator is
selected as wakeup from stop clock; otherwise HSI16 oscillator is
selected.
Signed-off-by: Giancarlo Stasi <giancarlo.stasi.co@gmail.com>
Add support for backup SRAM initialization found in multiple STM32
microcontrollers. Linker script facilities are also provided to make it
easy to define variables in the backup SRAM.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The STM32F2x was the only one of the STM32 series with a lowercase
input prompt. This looks odd in the SoC selection in 'menuconfig'.
Signed-off-by: Detlev Zundel <dzu@member.fsf.org>
Rather than Kconfig vendor symbols, select stm32 watchdog using
compatible.
So user only has to enable the requested node and set
CONFIG_WATCHDOG=y.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
