Add a composite fuel-gauge device to the Thingy53 to enable converting
the raw voltage to a battery percentage.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Flash partition was defining a scratch area which was implying the use
of mcuboot BOOT_SWAP_USING_SCRATCH f/w update method.
By removing this partition, mcuboot will automatically use
BOOT_PREFER_SWAP_MOVE method which should be prefered as it levels
flash wear. Incidentally increase slot1 by one sector (as this is
preferred for the swap method).
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Add Flexcomm signal sharing configuration for the mimxrt595s/cm33 and
mimxrt685s/cm33 SoCs. Properly instantiate the I3C peripheral for
interfacing with the WM8904's control port. Modify pinctrl DTs of
mimxrt595_evk/mimxrt595s/cm33 and mimxrt685_evk/mimxrt685s/cm33.
Instantiate the WM8904 codec for said boards.
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Signed-off-by: Yves Vandervennet <yves.vandervennet@nxp.com>
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
Enable DMIC clock in soc.c - attach to chip's audio PLL. Add pinmux
definitions for the DMIC peripheral. Add nodes to SoC's device tree for
the DMIC peripheral and its audio channels. Configure the DMIC
peripheral in board's device tree to enable audio capture.
Signed-off-by: Vit Stanicek <vit.stanicek@nxp.com>
Following addition of a `name` to hal_stm32 module, the command to fetch
blobs that are required to build BLE applications on STM32WBA socs is now
changed from `west blob fetch stm32` to `west blob fetch hal_stm32`.
Update documentation and warn users in migration guide.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
These boards support Bluetooth, so it should be listed under "supported".
There's also no (known) good reason to explicitly skip "net" tags, so
remove that from the ignore_tags list as well. We don't particularly know
or care about relevant net tests for these boards, so "net" is left out for
now from the "supported" list.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
These boards don't currently have the necessary binary blobs available
for Bluetooth, so keep their Bluetooth HCI DT node disabled.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Adds the default MCUboot operating mode when building using sysbuild.
Fix mcuboot sysbuild for frdm_mcxn947.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
Drop support for Google Kukui EC board which was used for
early Zephyr experiments but doesn't really exist anymore.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Background of this modification is to make clock control
driver code provided by Renesas vendor to support for Renesas MCU
on Zephyr.
Signed-off-by: Quy Tran <quy.tran.pz@renesas.com>
The heltec_wireless_stick_lite_v3 board does not properly handle
receive operations when the SPI used to communicate with onboard SX1262 has
the clock frequency set too high. This causes radio recv operation to
almost always hang forever without any error, as the SX1262 module returns
0xFF00 value as the interrupt status which does not make any sense, thus
causing the LoRaWAN library to trigger RXTX timeout handler which in the
current SX1262 driver implementation is not privded. The issue occurs
almost always, sometimes allowing to receive few (3-5) tranmissions
correctly, then fail. The root of the problem is not known for sure, but it
is highly likely a board's limitation, though not confirmed by the
manufacturer.
The current SPI frequency was chosen arbitrarily based on the conducted
experiments where the 30 000 messages have been received continiously
without any problems (with 5s interval for each message).
Signed-off-by: Patryk Biel <pbiel7@gmail.com>
Initial commit for entropy support on RA8
- drivers: entropy: implementation for TRNG driver of RA8x1
- dts: arm: add device node for trng of RA8x1
- boards: arm: enable support zephyr_entropy for ek_ra8m1 and
update board documentation
Signed-off-by: The Nguyen <the.nguyen.yf@renesas.com>
Signed-off-by: Duy Phuong Hoang. Nguyen <duy.nguyen.xa@renesas.com>
Add board support for Application, Radio and PPR cores
of the nRF9230 SoC / nRF9280 SiP on the nRF9280 PDK board.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Co-authored-by: Andreas Moltumyr <andreas.moltumyr@nordicsemi.no>
Adds a new board definition for the ADI MAX32690FTHR board. This board
uses the same SoC as the MAX32690EVKIT board, but with a smaller feather
form factor.
Tested on hardware with the following samples:
- samples/hello_world
- samples/basic/blinky
- samples/basic/threads
- samples/subsys/shell/shell_module
- samples/subsys/input/input_dump
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Updated the clocks that get initialized for the MCXN947
when using the LPTMR. The LPTMR allows the user to select
and Input clock, however said input clock must be
initialized before the user can select it.
Update description for clk-source in binding file.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Currently this code related to how to configure the
flash size and address when using flexspi to XIP is copy
pasted in all sort of places and ways all over the tree,
let's clean this up and have single point of control over
this configuration.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
To prepare for supporting flexcan, can node should be
renamed to canxl to support both flexcan and canxl
Signed-off-by: Tu Nguyen Van <tu.nguyenvan@nxp.com>
