Reworked i2c_sam_twi driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked i2c_sam_twi driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. We can remove
various defines from dts_fixup.h now as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. We remove the
aliases and use nodelabel instead in the soc_gpio.h to determine the
label for the specific gpio controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. This allows us to
also remove dts_fixup.h that are no longer used.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert from using dts_fixup.h based macros to DT_INST macro. This lets
us remove the dependancy on dts_fixup.h for this driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage. We also remove dts_fixup.h defines that
are no longer needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert from using dts_fixup.h based macros to DT_INST macro. This
lets us remove the dependancy on dts_fixup.h for this driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked usart_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked uart_sam driver to utilize new DT_INST macros as part of this
rework we also now get pin ctrl/mux configuration information from the
device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a set of macros that will create a struct soc_gpio_pin
initialization based on data extracted from device tree. This should
allow replacing the static data in soc_pinmap.h with data coming from
devicetree instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert from using dts_fixup.h based macros to DT_INST macro. This lets
us remove the dependancy on dts_fixup.h for this driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We don't need to define DT_NUM_IRQ_PRIO_BITS or DT_NUM_MPU_REGIONS in
dts_fixup.h files anymore, so we can remove them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To remove the need to have DT_NUM_IRQ_PRIO_BITS defined in every
dts_fixup.h we can just handle the few variant cases in irq.h. This
allows us to remove DT_NUM_MPU_REGIONS from all the dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the MCLK clock configuration symbol fix-up for the
GMAC peripheral.
The APB-agnostic clock configuration fix-up symbols map to the
SoC-specific APB, in order to accommodate different SoC variants with
the GMAC on different APBs.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Make use of DT_NODELABEL macros to get device instances
information to configure drivers I2C instances.
This allows to remove I2C related lines in fixup.h files
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use compatible information to configure i2c stm32.
With this, driver version selection is done thanks to compatible
and it is not needed anymore to do this via Kconfig symbol
selection under soc/
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a helper macro that will go from a DT_DRV_INST number and return the
clock_ip_name value for that instance.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move soc.c code to utilize DT_NODELABEL
instead.
Also rename various node labels to match the SoC docs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
z_power_soc_deep_sleep() is called with interrupt locked already
so restoring BASEPRI is pointless here, as it would only allow
exceptions afterwards. The situation is complicated by the fact
that kernel/idle.c:idle() only locks interrupt without unlocking
which means the BASEBRI at entry of z_power_soc_deep_sleep() is
already set to allow exceptions only but not lower priority
interrupts like timer. So when, e.g. timer, interrupt fires,
the SoC would come out of deep sleep but the waking interrupts
are never delivered since they are masked, and idle() will try
to sleep again. And now it gets into a loop of going into deep
sleep briefly and waking up immediately and it goes on and on.
The solution is not to restore BASEPRI and simply leave it at
zero. This is a workaround as a proper fix would involve
invasion changes to the PM subsystem.
Also, _sys_pm_power_state_exit_post_ops() is not being called
when deep sleep is involved, so PRIMASK needs to be reset
after coming out of deep sleep.
Fixes#23274
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This moves enabling XTENSA_HAL to the SoC definitions.
As Xtensa SoCs are highly configurable, it is possible
that the generic Xtensa HAL provided in the tree is
not suitable. So only enable XTENSA_HAL only if
the generic version can be used.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use the new devicetree API in a file which cross-checks dt reg base
addresses with values from the vendor HAL.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
When enabled, instead of erasing entire flash page at once, page will
be erased in defined time slices. Erasing single page stalls CPU
for significant time share (~80ms) and partial erase divides the
operation in to the shorter time periods, resuming CPU operation in
meantime and enabling better scheduling of time sensitive operations.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
To ease driver configuration, enable ENTROPY_STM32_RNG
only if device node matching driver compatible is enabled.
No more need to enable config symbol under soc/
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert stm32 entropy driver to configuration based on device tree.
Select HAS_DTS_ENTROPY symbols and configure CONFIG_ENTROPY_NAME
in fixup files.
Since rng node is not enabled (or available) on all boards, it could
happen that symbol ENTROPY_STM32_RNG is not enabled and hence
ENTROPY_HAS_DRIVER not selected which ends up with a symbol
ENTROPY_NAME defined throufg Kconfig selection. Thus, in fixup file,
CONFIG_ENTROPY_NAME is defined only if not already defined.
Additionally, update boards that used to configure entropy by default.
On these boards, enable rng device in device tree and remove Kconfig
related configuration (which should not be part of default
configuration).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Instead of using Kconfig options for setting the device name and IRQ
priority for the entropy_nrf5 driver, get these settings from the rng
node defined in DTS for a given SoC.
Provide also fixups for CONFIG_ENTROPY_NAME, until applications using
entropy drivers are converted to use DTS as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Also update counter_basic_api test to use DT_INST and remove the
udoo_neo_full_m4.conf as its not longer needed since the per instance
Kconfig sybmols don't exist anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Additionally remove udoo_neo_full_m4.conf from gpio_basic_api test since
the Kconfig symbols don't need to be set anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move soc.c code to utilize DT_NODELABEL
instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
