This patch reworks the current ARM __swap() function into a C function.
Due to some issues with using svc calls withing fault handlers, we
needed to change the way we initiate a swap by removing the dependence
on svc #0.
Before __swap() is called, the system has already done an irq_lock().
Upon return from __swap(), the equivalent of an irq_lock() is done due
to restoration of the key value from the irq_lock preceeding the call.
For ARM V6M (M0/M0+), the pendsv bit is toggled and the irqs are
enabled. There is no priority masking in v6m, so it's just a global
enable. For ARM V7M, the priority mask has to be set to 0x0 to allow
for the pendsv IRQ to be taken. This is done for both via a call to
irq_unlock(0).
After this unlock, a pendsv irq will be taken, either at the tail end
of the current irq handling if we are in handler mode, or immediately
due to the pendsv being asserted (no other outstanding irqs). The next
thread will be scheduled.
Upon return from the context switch to the original
thread, the priority mask will already be correct due to the pendsv
processing.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
MPU_STACK_GUARD option has a direct dependence on ARM_CORE_MPU.
Therefore, it is not required to have a conditional selection
of the option (if ARM_CORE_MPU) in ARM_STACK_PROTECTION.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
In ARMv7-M (and ARMv8-M) architecture it is
implementation defined whether separate MMFAR and BFAR are
implemented. This commit ensures that we always get the true
faulting address displayed in case of MemManage- or BusFault.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Move common SoC dts.fixup defines into arch/arm/soc/<SOC>/dts.fixup so
we remove duplication in the boards and only have board specific
defines in boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/atmel_sam/<BAR>/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into arch/arm/soc/nxp_imx/rt/dts.fixup
so we remove duplication in the boards and only have board specific
defines in boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/kwx/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/kl2x/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_lpc/lpc54xxx/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/nxp_kinetis/k6x/dts.fixup so we remove duplication in the
boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move common SoC dts.fixup defines into
arch/arm/soc/ti_simplelink/<BAR>/dts.fixup so we remove duplication in
the boards and only have board specific defines in
boards/arm/<FOO>/dts.fixup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add SPI fixup defines on STM32 SoC family level for all SPIs that
are supported on one or more SOCs of that SoC family.
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
The xtensa-asm2 work included a patch that added nano_internal.h
includes in lots of places that needed to have _Swap defined, because
it had to break a cycle and this no longer got pulled in from the arch
headers.
Unfortunately those new includes created new and more amusing cycles
elsewhere which led to breakage on other platforms.
Break out the _Swap definition (only) into a separate header and use
that instead. Cleaner. Seems not to have any more hidden gotchas.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The old ARMV6_M Kconfig option has been removed, and so to correctly set
the dependencies for SW_VECTOR_RELAY we need to use the new
ARMV6_M_ARMV8_M_BASELINE.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This patch fixes a hole in the stack guard configuration. The initial
branch to main is missing the stack guard configuration.
Fixes: Issue #3718
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch fixes calculations for the top of the interrupt and main
stacks. Due to power of two alignment requirements for certain MPUs,
the guard size must be taken into account due to the guard being
counted against the initial stack size.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support for userspace on ARM architectures. Arch
specific calls for transitioning threads to user mode, system calls,
and associated handlers.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds a configure_mpu_user_context API and implements
the required function placeholders in the NXP and ARM MPU files.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Atmel SAMD21 series was classified too broadly as SAMD.
This patch names it correctly to make room,
for other members of SAMD series
Signed-off-by: Sean Nyekjaer <sean@nyekjaer.dk>
Also pull out the SERCOM pads configuration to defines. Note that the
SAM0 has a two level configuration - a signal (like TX) is mapped to a
pad, and then a pad is mapped to a function on a pin.
Signed-off-by: Michael Hope <mlhx@google.com>
This commit defines the Kconfig options for
ARM Cortex-M23 and Cortex-M33 CPUs. It also
udpates the generic memory map for M23 and M33
implementations.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This PR includes the required changes in order to support
conditional compilation for Armv8-M architecture. Two
variants of the Armv8-M architecture are defined:
- the Armv8-M Baseline (backwards compatible with ARMv6-M),
- the Armv8-M Mainline (backwards compatible with ARMv7-M).
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Whenever a Cortex-M0+ supports the VTOR register it makes no sense to
use the software vector relay mechanism. Therefore change the logic so
that SW_VECTOR_RELAY does not get enabled whenever a VTOR register is
present, but enable it if an M0+ has no VTOR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This patch adds the generation and incorporation of privileged stack
regions that are used by ARM user mode threads. This patch adds the
infrastructure for privileged stacks. Later patches will utilize the
generated stacks and helper functions.
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Replace seldom occurrences of FLASH_DRIVER_NAME by equivalent
and commonly used FLASH_DEV_NAME.
Fixes#5919.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Some ARMv6-M Cortex-M0+-based SOCs have VTOR register
and can relocate vector table just as ARMv7-M ones.
Vector table relocation path should be choosed
by VTOR presence, not by arch.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
Defines the FLASH_DRIVER_NAME macro in soc.h for kinetis kl2x and kwx
SoC series. This macro is used by the storage and dfu subsystems, as
well as the flash_shell sample.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Rename the nano_internal.h to kernel_internal.h and modify the
header file name accordingly wherever it is used.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Currently in zephyr the support for the arm userspace has not be
merged. But the Kconfig always sets the userspace flag and causes a
build failure. This is blocking the test cases for userspace.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Add a new Kconfig option, BOOTLOADER_MCUBOOT, that automatically sets
the required options necessary to make the resulting image bootable by
the MCUboot open source bootloader. This includes the text section
offset and the vector relay table for Cortex-M0, and in the future it
might also add the DTS overlay required to link at slot0 offset in
flash.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add device tree support for the "nxp,kinetis-ftfa" flash controller used
on the NXP KL2X and KW4xZ SoCs.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert NXP k6x and kw2xd flash driver to use device tree to get the
flash controller name from device tree. We introduce yaml bindings for
the "nxp,kinetis-ftfe" and "nxp,kinetis-ftfl" devices.
Fixes: #5788
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The old HAL and MDK have been removed from the source tree.
Since RADIO HAL is not yet present in nrfx, the "nrf_radio.h" file
was temporarily moved to "nrfx/hal" folder. It will be replaced with
the proper file from nrfx in its next update.
Signed-off-by: Michał Kruszewski <michal.kruszewski@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This commit adds a glue layer that adapts nrfx to be usable in Zephyr
as a host environment and files with static configuration of nrfx
drivers for several supported SoCs.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This moves and merges the existing board-level dts.fixup files
for STM32 L4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
disco_l475_iot1 boards fixup blocks for devices connected via SPI
and I2C stay in board level dts.fixup file, because they are board
specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F3 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F1 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F4 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
96b_carbon boards fixup block for Bluetooth HCI device via SPI
stays in board level dts.fixup file, because it is board specific.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
This moves and merges the existing board-level dts.fixup files
for STM32 F0 SOC family into one soc family level dts.fixup file.
No new fixup blocks have been added, only fixup blocks, that were
part of at least one board level dts.fixup file are present in
soc family level dts.fixup file.
Contributes to #5707
Signed-off-by: Daniel Wagenknecht <wagenknecht.daniel@gmail.com>
Convert Atmel SAM0 flash driver to use device tree to get the flash
controller name and base address.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
