Manufacturer id is skipped when reading jedec_id, due to wrong
address mode.
Before: flash_stm32_ospi: Jedec ID = [60 20 00]
After: flash_stm32_ospi: Jedec ID = [ef 60 20]
Signed-off-by: Brian Juel Folkmann <bju@trackunit.com>
Change introduces a new configuration option that can be used to disable
GPIO interrupt support to reduce memory footprint.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
Configure the Number of Completed Packets event threshold to 1, so the
SiLabs Bluetooth controller will always send the Number of Completed
Packets HCI event to the host, even for small numbers of transmitted
packets.
Fixes#62279
Signed-off-by: Markus Fuchs <markus.fuchs@ch.sauter-bc.com>
Make HCI driver compatible to the updated versions of the
EFR32 Bluetooth library BLOBs consisting of:
* libbluetooth_controller
* libbgcommon
* librail
Signed-off-by: Markus Fuchs <markus.fuchs@ch.sauter-bc.com>
Use DEVICE_DT_INST_DEFINE instead of DEVICE_DEFINE to declare the device
structure. This ensures that the device gets an ordinal and is
initialized before any device depending on it.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Initial version of Infineon CAT1 SPI Driver supporting synchronous
and asynchronous data transfer API
Signed-off-by: Sreeram Tatapudi <sreeram.praveen@infineon.com>
Adds support for forcing XIP support at boot time, and reduces the
init priority of the driver so that it inits earlier.
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
ST7735S requires the COLMOD command be repeated as part of writing
pixels, otherwise it goes back to some kind of default which is likely
wrong.
ST7735S works correctly after this plus the previous two commits; tested
on STM32L462 + KD0096FM.
Signed-off-by: David Lamparter <equinox@diac24.net>
Use a continuous transaction with CS kept low for the entire batch of
row address, column address and actual pixel data write. This is
required by ST7735S and shouldn't hurt elsewhere.
Signed-off-by: David Lamparter <equinox@diac24.net>
When doing a TX-only SPI operation, the RX not empty flag will never get
set, thus this will just hang forever.
Found/tested on STM32L462 trying to drive some WS2812 RGB LEDs.
Signed-off-by: David Lamparter <equinox@diac24.net>
Add driver for the TI TCAN4x5x series of CAN controllers. These CAN
controllers are based on the Bosch M_CAN IP and interfaced via an SPI bus.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Create dac_mcxu_lpdac.c file to implement mcux lpdac, add binding for
the mcux lpdac, update Kconfig.mcux and CMakeLists.txt file to support
mcux lpdac.
Signed-off-by: Albort Xue <yao.xue@nxp.com>
Reset the device on initializing if reset-node is available in dts.
`snps,desingware-i2c` does not define reset-node itself.
Add more of an element that inherits `reset-device.yaml` to
the `compatible` section to allow defining the reset-node
for using this feature.
For example.
```
compatible = "reset-device-inherit-node", "snps,designware-i2c";
```
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
This commit resolves an internal dependecy between GET_DIRECTION and
GET_CONFIG configuration. GET_CONFIG api is internally needed by
GET_DIRECTION api.
Signed-off-by: Martin Kiepfer <m.kiepfer@teleschirm.org>
The Nuvoton NCT38xx is a multi-function device providing a TCPC
controller and a I/O expander (GPIO driver). Add a multi-function
driver to manage exclusive access to the device.
Tested with "twister -T tests/drivers/build_all/gpio".
Signed-off-by: Keith Short <keithshort@google.com>
the sam xdmac driver does not yet implement the
get_status() function. with this commit the function
will be implemented. Fixes#62003
Signed-off-by: Sven Ginka <sven.ginka@gmail.com>
Seems like the SSD1306 controller needs a bit of time after power up
before it can take i2c commands. This causes problems with
microcontrollers that have no other delays in the startup sequence, like
rpi_pico.
There's currently no good way of modeling this in Zephyr right now, and
there's also no clear indication of how much time the device needs in
the datasheet that I could find, but it seems like 10ms is enough for
that to start reliably so add a delay in the ssd1306 init function to
ensure that at least that time has passed from system power up.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Remove `threshold-reg-offset` DT property and implement them with static
inline functions in `reg_def.h`
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add `thr-sel` prop. to select the relevant threshold register for adc
comparator since there're two adc modules in npcx4 series.
Signed-off-by: Kate Yen <htyen@nuvoton.com>
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add multi-device support in npcx adc driver since there is more than one
adc module in npcx4 series. And each adc's reference voltage might be
different, this CL introduces the `vref-mv` prop. to select its own
reference voltage.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Signed-off-by: Kate Yen <htyen@nuvoton.com>
Only provide implementations for optional operations if needed. This
patch deletes quite a few dummy `pin_interrupt_configure` ops (now
optional), and adjusts ifdeffery on some drivers so that optional ops
are only provided if they implement real functionality.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This change allows to have GPIO interrupts configured
that will work while chip enters low power modes where
PD_COM is turned off.
PDC controller can wake up system on GPIO changes even when
PD_COM is off.
This is done by adding PDC entries that will wakeup Cortex-M33
at the same time when WAKEUP controller is programmed to
handle GPIO state changes.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Hardware supports only one edge for GPIO interrupt.
This adds software implementation that hides hardware restriction.
With this change user code can use GPIO_INT_TRIG_BOTH and does not
have to do it in application code.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Init level for GPIO drivers is set PRE_KERNEL_1.
Smartbond(tm) driver had it set to POST_KERNEL by accident.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Fix the whole v_empty setting code, this was using a wrong scaling
factor, but also incorrectly clearing the recovery voltage part of the
register.
Change the code to read the previous value and mask out the bits not
used by VE.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Introduce I2C target transfer using the PIO mode. Add an option
"target-pio-mode" in the yaml file, determined by the DTS, to dictate
whether I2C target transfer uses the PIO mode.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Disable the timeout setting when both the clock and data are
in a low state. This allows for I2C host clock stretching
without a timeout limit.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
IT8XXX2_I2C_STR is a register of read-only, non-writable to clear.
Here we can set hardware reset bit in the IT8XXX2_I2C_CTR register
to clear the status of IT8XXX2_I2C_STR.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The old acpi implimentation is replaced with acpica interface
and updated x86 arch porting with the new interface.
Signed-off-by: Najumon B.A <najumon.ba@intel.com>
Previously the pwm capture only support capturing on channel 1
and 2, because the slave mode controller was used, which uses
the signal TIxFP which is not available for channel 3 and 4.
This commit adds optional support for four channel capturing by
changing the method of capturing PWM signals to not use the
slave mode controller to reset the counter register. Instead the
counter is reset in the ISR. This will result in a slight loss
of accuracy but is still within an acceptable range.
Co-authored-by: Jeroen van Dooren <jeroen.van.dooren@nobleo.nl>
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
This commit adds option to dump i2c messages of only specified
devices. It makes it easier to debug communication of specific
i2c device instead of logging all i2c communication.
The filter of devices is specifiec in device-tree using the
node with "zephyr,i2c-dump-filter" compatible string.
Example of device-tree node:
i2c-dump-filter {
compatible = "zephyr,i2c-dump-filter";
devices = < &display0 >, < &sensor3 >;
};
Signed-off-by: Michał Barnaś <mb@semihalf.com>
