Use standard log settings. Since default LOG_IMMEDIATE has changed to
output one character we have one character ring buffer slots which
limit amount of logs stored.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Fix the following device tree warnings:
unit-address and first reg (0x20000) don't match for iccm@0
unit-address and first reg (0x80010000) don't match for dccm@80000000
Since the em_starterkit_em7d_normal has a different base address for
iccm & dccm, and most of the em_starterkit variants have different sizes
for iccm & dccm. Just define the nodes in the specific
em_starterkit*.dts file and remove them from emsk.dtsi. This removes
the issue reported in the warning.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the following device tree warnings:
unit-address and first reg (0x40000) don't match for iccm@0
unit-address and first reg (0x80040000) don't match for dccm@80000000
Re-work iccm and dccm reg address and size to be based on #defines.
This allows the nsim_sem_normal.dts to override defaults that are set in
nsim.dtsi. Utilize DT_ADDR macro to take a 'unit-address' still value
and convert it into a hex value (just prepending 0x).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Create an SoC definition for the Audio DSP on Intel Apollolake
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it. Not all aliases appear to be present, but using instances breaks
because the ports used by different boards do not always start with
the first.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This breaks down the GPIO controller definition in DTS into
multiple entries. This allows these controllers to be
referenced by other DTS, and test board overlay files.
And also we can remove the entries in the dts fixup file.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This commits adds GPIO driver for LiteX SoC builder.
Due to the fact that GPIO in LiteX is unidirectional and can be
configured with different pins amount per port, additional entries
were added to the dts file.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
The current sam spi driver uses soc dependent name which duplicate
configuration to enable other platforms. This refactor current
definitions to a generic way to reuse symbols by multi soc definitions.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add option for keeping the watchdog timer of the NXP Kinetis KE1xF SoC
series enabled at boot with a configurable, initial timeout.
This removes the risk of failure from when z_arm_watchdog_init()
disables the watchdog timer until the application code configures a
timeout and re-enables the watchdog timer.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The xcc specific reentrant syscall implementations are actually useful
for xtensa in general. So move that code from being specific to
intel_s1000 / xcc into generic newlib/libc-hooks.c. This is in prep
for the Zephyr SDK dropping -DMISSING_SYSCALL_NAMES which will make
its version of newlib on xtensa match behavior with xcc.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the following:
- device tree bindings for Gecko watchdog driver
- EFM32PG SOC support for the watchdog driver
- EFM32PG board support for the watchdog driver
- DTS aliases for testing with default watchdog driver test
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Enable the shared IRQ for the UART line and enable the remaining tasks
that depends on a separated declaration of the TX/RX/Err/... IRQs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Lot of misdefined variables that went in undetected due to lack of CI on
this board. Fix them and test build with new SDK.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit adds the remaining gpio ports I, J and K to the device
tree and dts_fixup headers of the EFM32JG12B and EFM32PG12B SoCs.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
The Silicon Labs EFM32 Jade Gecko MCU includes:
* Cortex-M3 core at 40MHz
* up to 1024KB of flash and 256KB of RAM
* multiple low power peripherals
This is basically the same as the EFM32 Pearl Gecko, but with an ARM
Cortex-M3 core instead of a Cortex-M4F.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Disable the early watchdog initialization for the NXP Kinetis series
if the application is to be chain-loaded by mcuboot.
The early watchdog initialization must only take place once and needs
to happen within a SoC specific number of CPU clock cycles after
reset.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move CONFIG_WDOG_INIT for the NXP Kinetis series to the top-level
Kinetis Kconfig file and enable it where needed.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move the NXP Kinetis KW4xZ watchdog initialization code to
z_arm_watchdog_init() and make it optional based on CONFIG_WDOG_INIT.
This brings the KW4xZ in line with the other NXP Kinetis series SoC
implementations.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move the NXP Kinetis KL2x watchdog initialization code to
z_arm_watchdog_init() and make it optional based on
CONFIG_WDOG_INIT.
This brings the KL2x in line with the other NXP Kinetis series SoC
implementations.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The driver for STM32's independent watchdog already exists and is
compatible with the stm32l1 SoC. Enable the independent watchdog
for the stm32l1 series for use with this driver.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
Instead of having TI_CCFG_PRESENT as a symbol that's only defined in
soc/arm/ti_simplelink/cc13x2_cc26x2/Kconfig.defconfig.series and y when
SOC_SERIES_CC13X2_CC26X2 is enabled, turn it into a helper symbol that's
selected by SOC_SERIES_CC13X2_CC26X2.
This avoids having a symbol that's only defined in a Kconfig.defconfig
file, which is confusing. It also makes things a bit more generic, in
case other boards with CCFGs are added.
Also rename it to HAS_TI_CCFG to be consistent with other helper
symbols, and add a help text.
Flagged by scripts/kconfig/lint.py.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Added delay before starting low frequency clock for the first time to
ensure that anomaly conditions are not met. Delay is configurable and
might be disabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This reverts commit 49bd19f3f2,
as the patch it contains is no longer needed after nrfx is updated
to version 2.1.0.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update the hal_nordic module revision, to switch to nrfx 2.1.0.
Because the list of peripherals for nRF5340 has changed as follows:
- SPIM2 has been renamed to SPIM4
- SPIM2-3, SPIS2-3, TWIM2-3, TWIS2-3, and UARTE2-3 have been added
a couple of related corrections needed to be applied in dts and Kconfig
files, plus the spi_nrfx_spim driver has been extended with the support
for SPIM4.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
DesignWare driver can manage different amount of irqs so let's make it
configurable via DTS.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Remove soc/arm/st_stm32/stm32YY/flash_registers.h files.
Change register accesses in stm32 flash drivers to use FLASH_TypeDef
from modules/hal/stm32/stm32cube/stm32YYxx/soc/stm32xxxxxx.h.
Fixes#16235
Signed-off-by: Sarvesh Patkar <psarvesh314@gmail.com>
