The PWM period cell will soon be required by the pwm_dt_spec facilities.
This patch adds support for it.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Customize busy wait timer for micro-seconds accuracy.
Verified by follow test pattern:
west build -p auto -b it8xxx2_evb tests/kernel/timer/timer_api
west build -p auto -b it8xxx2_evb tests/kernel/timer/timer_error_case
west build -p auto -b it8xxx2_evb tests/kernel/timer/timer_monotonic
west build -p auto -b it8xxx2_evb tests/kernel/timer/starve
west build -p auto -b it8xxx2_evb tests/kernel/context
west build -p auto -b it8xxx2_evb tests/drivers/adc/adc_api
Signed-off-by: Ruibin Chang <Ruibin.Chang@ite.com.tw>
Enable the alt function with setting both bit5@0xf016f1 and
bit6@0xf02046 bits will cause internal leakage.
Only bit6@0xf02046 bit is required to enable the alt function,
so fix it.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
As mentioned in #42882, the I2C of IT8XXX2 is designed for two different
IP blocks, so this PR divides this I2C driver into two compatibles.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The ADC driver of IT81302 chip can support channels 0-7 & 13-16.
This PR adds to implement ADC channels 13-16.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
This enables the below configuration so the AP and EC are able to
communicate over eSPI:
CONFIG_ESPI_PERIPHERAL_EC_HOST_CMD
CONFIG_ESPI_PERIPHERAL_ACPI_SHM_REGION
CONFIG_ESPI_PERIPHERAL_CUSTOM_OPCODE
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
The default I2C channel 3 is used by alternate function of GPIO H1/H2
Krabby uses GPIO F2/F3 as I2C channel 3, so we need to add the
compatibility of the GPIO F2/F3.
TEST=test on it8xxx2_evb:
zmake configure -b zephyr/projects/it8xxx2_evb/
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
If there are no console messages input at an interval of 15
seconds, the system will be able to enter suspend mode.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
IT8XXX2 uses shared ns16550.c driver which does not provide a power
management callback(pm_action_cb), so create driver to handle
IT8XXX2 specific UART features.
note: pm_action_cb(old name: pm_control_fn)
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add the power state of deep doze. When system enters deep doze, the
clock of CPU and EC can be stopped to reduce power consumption. And
enable the UART Rx WUI before entering deep doze to wake up EC and
CPU.
Tested on it8xxx2_evb board. It will reduce 5.25mA when system enters
deep doze mode.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Note that the it8xxx2 does not support a status register so that
functionality is omitted.
This change also adds driver tests that build both the npcx and it8xxx2
drivers.
Signed-off-by: Yuval Peress <peress@chromium.org>
This PR will change accessing the related pinctrl macro from soc_dt.h
And the pinctrl of SCL and SDA were got from pinctrl-0 and pinctrl-1,
respectively. Change it to get from pinctrl-0 only.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Use GPIO output high and low to simulate I2C start and stop
conditions to restore i2c to normal.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Create the pinmux phandle to the I2C driver node in the
devicetree. When the pinmux_pin_set function in
i2c_it8xxx2_init can refer to the setting of this phandle.
It is more flexible to use.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Add flash driver for it8xxx2. The driver can implement
flash read, write and erase that will be mapped to the
ram section for executing.
TEST="flash write 0x80000 0x10 0x20 0x30 0x40 ..."
"flash read 0x80000 0x100"
"flash erase 0x80000 0x1000"
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Create the pinmux phandle to the ADC driver node in the
devicetree. When the pinmux_pin_set function in
adc_it8xxx2_channel_setup can refer to the setting of
this phandle. It is more flexible to use.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The default status of UART should set disabled.
If UART needs to enable, it will be set in the
dts of board level.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
This change enables A, C, D, E, G, H, I, J, K, and L groups,
and fix gpio interrupt function.
This change also pull (and rename) dt-bindings/irq.h to
dt-bindings/interrupt-controller/ite-intc.h, because it is
chip-specific.
Signed-off-by: Dino Li <Dino.Li@ite.com.tw>
Change-Id: Ifee039981c2cc4cf5980e663702a9921e629fc1e
This commit is about the it8xxx2 analog to digital converter
driver. Support 8 channels ch0~ch7 and 10-bit resolution.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit is about the it8xxx2 i2c master driver which
includes six SMBus channels. The enhanced channel i2c3,
i2c4, i2c5 are controller which are designed to support
the I2C protocol.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
This commit is about it8xxx2 platform device tree.
Add driver's binding files, and one device tree as sample.
Signed-off-by: Cheryl Su <cheryl.su@ite.com.tw>
