In the wake of introducing nRF9160 .dtsi header, we are
adding several HAS_HW_NRF_xxxx Kconfig symbols, for the
peripherals present in nrf9160 SoC.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Make the following nRF peripheral drivers:
- ADC
- GPIO
- I2C
- SPI
- UART
- USB_DEVICE
enabled by default so that users do not need to explicitly enable them
in their applications after choosing an nRF SoC as the build target.
Kconfig options enabling these drivers depend on both a given hardware
feature (e.g. I2C) and an nRF family SoC selected, so effectively they
will be automatically enabled only when it is adequate (and in most
cases these drivers are the only option for a given hardware feature
on nRF SoCs).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Implementations of both flavors of serial drivers for Nordic SoCs
are no longer dependent on the gpio driver. Remove the dependency
from Kconfig.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Added board definitions for nucleo_f756zg. Features include gpio,
pinmux, uart (ST Zio, ST-Link and Arduino Uno v3 interfaces).
Added basic documentation and some soc definitions for the
stm32 f756XX soc.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
The early boot watchdog init for kinetis was incorrectly disabling and
reenabling interrupts to preserve timing during the unlock sequence.
However, interrupts are already disabled before this routine executes
and the kernel is not yet ready to enable them when this routine exits.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds a flash driver for the STM32F7x series, inspired from
the STM32F4x one. It has been tested on the STM32F723, but should also
work on other SoCs of the family.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This patch cleans up the code in the recently added dts_fixup.h,
restoring the original alignment of the file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The dts.fixup for v2m_beetle contains a wrong setting for the IRQ fixup
for the Dual Timer IRQ.
This patch fixes the symbol included in the generated header.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This commit simplifies Kconfig options related to handling SoC series,
part numbers. This is a first step required to add remaining part
numbers to the existing configuration.
This change is possible since all SiLabs SoCs within a single series
have a very uniform structure.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The driver can be tested using different networking emulation
approaches.
This approach will work across multiple Qemu instances. There can be
more than one Qemu instance, run using the following command. They
would appear to be on the same Ethernet network.
$ qemu-system-arm -M lm3s6965evb \
-serial stdio \
-net nic \
-net socket,mcast=230.0.0.1:1234 \
-kernel zephyr.elf
This approach will work with other virtualization technologies that
support connecting to a VDE switch, like VirtualBox and User Mode
Linux. The switch can be started using the following command.
$ vde_switch --sock /tmp/switch
Qemu can be connected to the switch using the following command.
$ qemu-system-arm -M lm3s6965evb \
-serial stdio \
-net nic \
-net vde,sock=/tmp/switch \
-kernel zephyr.elf
Signed-off-by: Fadhel Habeeb <fadhel@zilogic.com>
Signed-off-by: Nirav Parmar <niravparmar@zilogic.com>
Signed-off-by: Vijay Kumar B <vijaykumar@zilogic.com>
Add configuration values for HAS_HW_NRF_BPROT and HAS_HW_NRF_MPU.
Select these configurations where applicable.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
Within a single series pin mapping between location setting and pin name
is uniform. The only difference is availability of the module, i.e. i2c1
may be missing on some part numbers, or availability of the pin, i.e.
32 pin package will not provide all the pins available on 48 pin
package. It's better to manage these differences at the DTS/Kconfig
level.
This commit removes dependency of soc_pinmap.h files on part numbers.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Implementation taken from Nordic nrfx version 1.3.1 soc/nrfx_coredep.h,
modified to remove material from other series and to conform to Zephyr
coding standards.
Note that unlike standard k_busy_wait this is susceptible to
longer-than-intended delays due to the impact of interrupt handling.
Fixes#11626
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The Cortex-M7 CPU included in the SAM e70 SoCs has a data cache that
significantly boost the performances. However the SAM GMAC Ethernet
driver is using a scatter-gather technique to exchange data with the
Ethernet driver. This requires the use use of a non-cached memory area.
This is currently not supported on Zephyr, but support for it is being
discussed in PR#11199.
In the meantime, enable the data cache during the SoC initialization,
unless the SAM GMAC Ethernet driver is enabled.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The Cortex-M7 CPU included in the SAM e70 SoCs has an instruction cache
that significantly boost the performances. Enable it during the SoC
initialization.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The Silicon Labs EFM32 Pearl Gecko MCU includes:
* Cortex-M4F core at 40MHz
* up to 1024KB of flash and 256KB of RAM
* multiple low power peripherals
Ported from EFM32WG:
https://www.silabs.com/documents/public/application-notes/an0918.0-efm32_to_efm32jgpg_migration_guide.pdf
Signed-off-by: Gil Benkö <gil.benkoe@pm.me>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Declare and define nxp_mpu_config and nxp_mpu_regions
structs as const, as they are not modified in run-time.
Fixes#10320
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Declare and define arm_mpu_config and arm_mpu_regions
structs as const, as they are not modified in run-time.
Fixes#10320
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds support for STM32L471xG. Since STM32L475 only adds
USB, stm32l475.dtsi now includes stm32l471.dtsi
Signed-off-by: Kiril Zyapkov <k.zyapkov@allterco.com>
This patch adds a flash driver for the Atmel SAM E70 SoC. The driver has
been kept simple by considering that the flash is only composed of 8-KiB
blocks. Indeed an area at the beginning of the flash might be erased
with a smaller granularity, and the other blocks can also be erased with
a higher granularity. It also only handles the global read/write
protection, not the 128-KiB lock regions. A write error is returned if
a region is locked.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Enables Networking hardware on i.MX-RT 1050-EVKB board.
Pinout enabled board specific etherenet connection, also pin
initialization was moved later to PRE_KERNEL_2 in order to have
sysclock initialized before.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Convert the Atmel SAM0 watchdog driver to the new watchdog API and
enable DTS support.
This fixes#10914.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add Messaging Unit B peripheral support for i.MX6SoloX soc so it can
use IMX IPM.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
When the WNC-14A2A modem binding was originally introduced, I thought
the base_label would shorten the define keeping the result short and
easily portable. Turns out with the latest changes, it has a side
effect of removing the "DT_*" prefix which is breaking the build.
Let's remove "base_label" from the modem binding and adjust all of
the dts_fixups referring to the WNC14A2A defines.
NOTE: This commit moves the left-over WNC14A2A dts_fixup defines from
the nRF52 soc into samples/net/lwm2m_client as the new values.
They will stay there until the modem can be re-configured as a shield.
Signed-off-by: Michael Scott <mike@foundries.io>
