This patch re-namespaces global variables and functions
that are used only within the arch/arm/ code to be
prefixed with z_arm_.
Some instances of CamelCase have been corrected.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The SoC clock init code for USB was using a deprecated DTS define.
Switch to using the non-deprecated form.
Fixes: #17772
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SoC initialization code used timer clock frequency
as a system clock frequency. This commit corrects that by
obtaining the needed value from DTS.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Implementation of pinmux of usdhc depends on board design.
Usdhc driver could change pinmux according to SD mode, SoC
should provide API for this. Board pinmux should register
its pinmux function to SoC.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
In kernel_arch_init() we initialize the ARM core (interrupt
setup, fault init, etc.) so we can also move z_clearfaults()
in the same function and skip invoking it in the SoC init
functions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
add usbd1 definition to rt dts file,
set EHCI controller config default value in rt1050 default config file,
add EHCI controller driver MACROs to dts_fixup.h,
initialize EHCI clock in rt soc.c
add HAS_MCUX_USB_EHCI for supported soc in Kconfig.soc
Signed-off-by: Mark Wang <yichang.wang@nxp.com>
Enables the mcux elcdif shim driver and clocks on imx rt socs when the
display driver interface is enabled.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The ENET PLL should be enabled if the SoC is the MIMXRT1021 (it used by
the ARM core) or if the ENET device is enabled.
The 500MHz clock should be enabled if the SoC is the MIMXRT1021.
The ENET clock should be enabled if the ENET device is enabled.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Enables the mcux lpi2c shim driver and clocks on all imx rt socs when
the i2c driver interface is enabled.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds support for the device configuration data (DCD), which provides a
sequence of commands to the imx rt boot ROM to initialize components
such as an SDRAM.
It is now possible to use the external SDRAM instead of the internal
DTCM on the mimxrt1020_evk, mimxrt1050_evk, and mimxrt1060_evk. Note,
however, that the default board configurations still link data into
internal DTCM, therefore you must use a device tree overlay to override
"zephyr,sram = &sdram0"
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds support for the boot data, image vector table, and FlexSPI NOR
config structures used by the imx rt boot ROM to boot an application
from an external xip flash device.
It is now possible to build and flash a bootable zephyr image to the
external xip flash on the mimxrt1020_evk, mimxrt1050_evk, and
mimxrt1060_evk boards via the 'ninja flash' build target and jlink
runner. Note, however, that the default board configurations still link
code into internal ITCM, therefore you must set CONFIG_CODE_HYPERFLASH=y
or CONFIG_CODE_QSPI=y explicitly to override the default. You must also
set CONFIG_NXP_IMX_RT_BOOT_HEADER=y to build the boot header into the
image.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes an ethernet build error introduced with MCUXpresso SDK 2.5.0,
caused by a slight change in the ethernet pll configuration structure.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables Networking hardware on i.MX-RT 1050-EVKB board.
Pinout enabled board specific etherenet connection, also pin
initialization was moved later to PRE_KERNEL_2 in order to have
sysclock initialized before.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2018-09-13 00:56:48 -04:00
Renamed from arch/arm/soc/nxp_imx/rt/soc.c (Browse further)
