This commit is a part of introduction of new WTD instances.
It adds new Kconfig symbols that can be used in WDT shim and
nrfx driver.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Change makes EGU instance used for anomaly 109 workaround configurable.
The default EGU instance (5) may be used for other purpose.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
There are symbols are both defined by the NXP S32 HAL and
the CMSIS RTOS V2 wrapper, to avoid interference between
them, redefine the symbols under an enum.
Also this is may a common issue for all NXP S32 platforms,
move to common place to be reused
Signed-off-by: Dat Nguyen Duy <dat.nguyenduy@nxp.com>
r8a779f0 SoC is part of the Renesas R-Car Gen4 SoC series.
This SoC has a dual core lockstep Cortex-R52 CPU.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Renesas R-Car Gen4 is different from Gen3 regarding pinmux.
While Gen3 had only one base address to manage all pins,
Gen4 has one set of pinmux registers per GPIO banks.
We could expose one pinmux register per GPIO controllers,
but that would break potential compatibility with Linux
Device tree.
Instead create a reg_base array to parse all reg base from
device tree and identify proper base address based on the pin
definition.
This imply to add a pfc_base parameter to most of the pfc_rcar
function.
Signed-off-by: Julien Massot <julien.massot@iot.bzh>
Signed-off-by: Pierre Marzin <pierre.marzin@iot.bzh>
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
The original SHI module only has one output FIFO buffer. It costs a lot
when the driver has to send/change the protocol control code because it
must fill out all 128 bytes of output FIFO. In npcx4, we introduce
another output buffer in 1-byte depth. These two buffers can switch back
and forth during the transaction. We can use the single-byte buffer
to send the control code and the 128-byte FIFO to send the data payload.
It helps improve the SHI driver's efficiency.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Add soc power management for the STM32F4x chips.
One low power state is added supported by all chips from the family -
the Stop mode with voltage regulator in low-power mode.
The Stop mode for STM32F chips has to work with the IDLE timer -
CORTEX_M_SYSTICK_IDLE_TIMER, because PLL and HSI are disabled in the
Stop mode (Systick is not clocked). The only possible wakeup source is
RTC, which works as a IDLE timer for the Systick.
The exit latency may need to be adjusted per system, depending on the
system tick frequency and other variables.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
This commit moves configuration of hfxo from headers defined on board level
to device trees of SoCs.
Signed-off-by: Franciszek Zdobylak <fzdobylak@antmicro.com>
The SoC header already includes the necessary device headers for
all SoC variants supported.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
To simplify the inclusion of device headers in common code for
NXP S32 devices, make sure all SoCs are including their respective
device headers. This PR adds the missing headers for S32Z/E.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Add alias "FEATURE_SIUL2_MAX_NUMBER_OF_INPUT"
for compatibility with with previous RTD versions.
Signed-off-by: Cong Nguyen Huu <cong.nguyenhuu@nxp.com>
Currently, the NXP S32 SoCs have three redundant Kconfig hidden
options to define the part number. To streamline this, we will
retain `CONFIG_SOC_PART_NUMBER` to store the part number as a
string and `CONFIG_SOC_PART_NUMBER_<part>` that can be selected
by the boards.
Furthermore, for drivers requiring conditional code compilation
based on the target SoC, they should utilize the series or SoC
config option as applicable, instead of the part number config.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
The existing S32K3 Kconfig options employ the `M7` suffix, which is
redundant given that all cores in this series utilize an Arm Cortex-M7
core. Therefore, we should remove it.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
To accommodate support for S32K1 devices, it is necessary to rename
the existing `s32k` directory, which currently houses support for
the S32K3 series, to align with the respective series names. This
adjustment is necessary given the distinct differences in core
architecture, MPU, peripherals, and other key aspects between
the two series.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
CPU_HAS_NRF_IDAU is depending on SOC_SERIES_NRF91X and
SOC_NRF5340_CPUAPP.
This makes it more difficult to have an out-of-tree nrf SOC.
It is also an unnecessary dependency. There is no prompt for
CPU_HAS_NRF_IDAU, so it will not show up in menuconfig and it won't be
possible to enable it from a users Kconfig fragment.
The only way to enable it is to select it, and those that select this
option can themselves make sure that they only do so when appropriate.
Also, move NRF_SPU options out to SOC Kconfig files to also make
out-of-tree SoCs possible. With the added benefit of not polluting the
common soc/arm/Kconfig.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This adds a new driver for Renesas RZ/T2M.
The driver allows configuration of pin direction,
pull up/down resistors, drive strength and slew rate,
and selection of function for a pin.
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
This adds a new SoC: SOC_RENESAS_RZT2M
and a new board: rzt2m_startek_kit
Signed-off-by: Wojciech Sipak <wsipak@antmicro.com>
Co-authored-by: Roman Dobrodii <rdobrodii@antmicro.com>
This allows XIP to be disabled for applications that execute in
RAM, which do not need XIP support from flash
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Add support for mipi_dsi_detach API to dsi_mcux_2l driver, and
update RT5xx SOC interface to enable halting clocks for the MIPI DPHY.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
At present, many of the NXP S32 shim drivers do not make use of
devicetree instance-based macros because the NXP S32 HAL relies on an
index-based approach, requiring knowledge of the peripheral instance
index during both compilation and runtime, and this index might not
align with the devicetree instance index.
The proposed solution in this patch eliminates this limitation by
determining the peripheral instance index during compilation
through macrobatics and defining the driver's ISR within the shim
driver itself.
Note that for some peripheral instances is needed to redefine the
HAL macros of the peripheral base address, since the naming is not
uniform for all instances.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
At present, many of the NXP S32 shim drivers do not make use of
devicetree instance-based macros because the NXP S32 HAL relies on an
index-based approach, requiring knowledge of the peripheral instance
index during both compilation and runtime, and this index might not
align with the devicetree instance index.
The proposed solution in this patch eliminates this limitation by
determining the peripheral instance index during compilation
through macrobatics and defining the driver's ISR within the shim
driver itself.
Note that for some peripheral instances is needed to redefine the
HAL macros of the peripheral base address, since the naming is not
uniform for all instances.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Enable NXP FlexRAM in DTS and SOC code.
Do not configure flexram at runtime if the code is in the RAM.
Fix RT1060 DT to be more accurate.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Other drivers like the pinctrl_ti_k3 rely on a fully initialized system.
Move the am62x_init to an earlier stage than PRE_KERNEL_1 to keep both
PRE_KERNEL_{1,2} free for drivers.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
- Make caparray delta a Kconfig variable
- Set caparray delta for beagle_bcf at beagleconnect_freedom_defconfig
Signed-off-by: Ayush Singh <ayushdevel1325@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Support NXP MRT on LPC55XXX SOC series, enable on
lpcxpresso55s69_cpu0, add test overlay to counter basic api test
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
At present, many of the NXP S32 shim drivers do not make use of
devicetree instance-based macros because the NXP S32 HAL relies on an
index-based approach, requiring knowledge of the peripheral instance
index during both compilation and runtime, and this index might not
align with the devicetree instance index.
The proposed solution in this patch eliminates this limitation by
determining the peripheral instance index during compilation
through macrobatics and defining the driver's ISR within the shim
driver itself.
Note that for some peripheral instances is needed to redefine the
HAL macros of the peripheral base address, since the naming is not
uniform for all instances.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
NXP USB bindings were combined into one binding and using
a property corresponding to HAL enums which is improper use
of devicetree.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
This CL is to minimize `CONFIG_SOC_SERIES_XXXX` definitions when we
introduce a new chip series. Most of them are relevant to register
layouts in different npcx soc series. It moves soc-specific register
definitions from `reg_def.h` to its own soc.h file.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
At present, many of the NXP S32 shim drivers do not make use of
devicetree instance-based macros because the NXP S32 HAL relies on an
index-based approach, requiring knowledge of the peripheral instance
index during both compilation and runtime, and this index might not
align with the devicetree instance index.
The proposed solution in this patch eliminates this limitation by
determining the peripheral instance index during compilation
through macrobatics and defining the driver's ISR within the shim
driver itself.
Note that for some peripheral instances is needed to redefine the
HAL macros of the peripheral base address, since the naming is not
uniform for all instances.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
At present, many of the NXP S32 shim drivers do not make use of
devicetree instance-based macros because the NXP S32 HAL relies on an
index-based approach, requiring knowledge of the peripheral instance
index during both compilation and runtime, and this index might not
align with the devicetree instance index.
The proposed solution in this patch eliminates this limitation by
determining the peripheral instance index during compilation
through macrobatics and defining the driver's ISR within the shim
driver itself.
Note that for some peripheral instances is needed to redefine the
HAL macros of the peripheral base address, since the naming is not
uniform for all instances.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Fix cmake depreciation warning on pre-defined linker.id
(soc/arm/renesas_ra/ra4m1/linker.ld) used for arduino_uno_r4_minima.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Allow user to disable CONFIG_ADJUST_DCDC for their board, rather than
selecting it at the SOC level. The symbol still defaults to enabled,
preserving existing behavior unless a user explicitly chooses to disable
it.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
At present, many of the NXP S32 shim drivers do not make use of
devicetree instance-based macros because the NXP S32 HAL relies on an
index-based approach, requiring knowledge of the peripheral instance
index during both compilation and runtime, and this index might not
align with the devicetree instance index.
The proposed solution in this patch eliminates this limitation by
determining the peripheral instance index during compilation
through macrobatics.
Note that for some peripheral instances is needed to define the
HAL macros of the peripheral base address because there are gaps
in the instances or there are SoCs with a single instance.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
This commit introduce 'USE_SWITCH' feature into cortex-A/R(aarch32)
architecture
For introducing USE_SWITCH, the exception entry and exit are unified via
`z_arm_cortex_ar_enter_exc` and `z_arm_cortex_ar_exit_exc`. All
exceptions including ISR are using this way to enter and exit exception
handler.
Differentiate exception depth and interrupt depth. Allow doing
context switch when exception depth greater than 1 but not allow doing
this when interrupt depth greater than 1.
Currently, USE_SWITCH doesn't support FPU_SHARING and USERSPACE.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
