It was reported, and confirmed by multiple parties that default
CONFIG_ETH_MCUX_RX_BUFFERS=2 under some packet load leads to
1s and increasing packet processing delay and eventual deadlock.
No reports were about CONFIG_ETH_MCUX_TX_BUFFERS=2, but be on safe
side and just set that to the minimal value as the current default,
to allow us to have good conservative base to test various networking
stack issues.
Fixes: #3132
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Correct it so that it is possible to use PWMs on nRF9160 as well,
not only on nRF5 family SoCs.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Minor adjustments are done to the nRF clock_control and rtc_timer
drivers to make them usable on nRF9160 as well.
The arm_irq_vector_table test code is modified only because it uses
the function that has been renamed in the nrf_rtc_timer driver.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Use the symbol generated from DT so that it is common for nRF9160
and nRF5 family SoCs. To avoid artificial renaming of CLOCK_POWER_IRQn
to POWER_CLOCK_IRQn.
For nRF5 family SoCs clock nodes were not defined so far, thus they are
added so that the proper DT symbol is generated for them as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
As emulated by QEMU. SMSC9118 is compatible with SMSC9220 as used in
ARM MPS2 board, as well as SMSC9115/6/7/etc. devices.
Portions of the code are based on mbedOS code from its
targets/TARGET_ARM_SSG/TARGET_CM3DS_MPS2/device/drivers/smsc9220_eth.c
eth_smsc9220_priv.h originally comes from Arm mbedOS file:
targets/TARGET_ARM_SSG/TARGET_CM3DS_MPS2/device/drivers/smsc9220_eth.h
augmented with struct & defines from:
targets/TARGET_ARM_SSG/TARGET_CM3DS_MPS2/device/CM3DS.h
and renamed as eth_smsc911x_priv.h to follow Zephyr conventions.
Then, following changes applied:
Changes to build under Zephyr, changes to use symbolic constants
and field access helpers, typo fixes, etc.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The eswifi controller is capable of acting as an Access Point.
Implement ap_enable/ap_disable methods.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Create eswifi_at_cmd and eswifi_at_cmd_rsp helpers, allowing to send an
at command and parse the at response. These methods return success if
the response contains the OK* string. The eswifi_at_cmd_rsp method
extracts response content/size (DATA) on success.
*Response format is:
\r\n[DATA]\r\nOK\r\n>
Where DATA can be arbitrary (ASCII or not).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Remove all references in the documentation and Kconfig options
to the legacy shell to avoid confusing users and developers
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Add a configuration structure to sht3xd that holds instance-specific
parameters, implemented in a immutable statically allocated object
initialized with material from device tree binding aliases.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Adds a shim layer around the mcux lpi2c driver to adapt it to the zephyr
i2c interface. This shim driver leverages heavily from the mcux i2c shim
driver because the MCUXpresso SDK provides similar APIs for the i2c and
lpi2c peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The SimpleLink wifi driver enables the Fast Connect method of
WiFi provisioning, which allows the network coprocessor to
reconnect to a previously connected Access Point (AP) on
startup.
Previously, if Fast Connect failed to connect, any network
socket applications would inevitably fail, as there would have
been no wifi connection.
This patch adds a configurable timeout for the Fast Connect
feature, after which timeout, an error is logged informing
the user to manually reconnect to an AP.
Reconnection is typically accomplished by separately running the
wifi sample shell program.
Fixes: #11889
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Commit aad21ecb31 introduced an incorrect
pattern of handling ADC sampling requests with invalid parameters in
both nRF ADC drivers. After discarding such request, the drivers do not
release properly the access lock and therefore become unusable.
Unfortunately, this pattern were later on copied in all other ADC
drivers in the source tree.
This commit adds the proper lock releasing in all the affected drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Due to a copy-paste mistake, this driver used an incorrect module
name (adc_mcux_adc16) in log messages.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Change driver to get I2C address of sensor from the device tree like
most other sensor drivers that utilize device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
15.4 MHR is no longer set in net_buf pointed by net_pkt, but in a
separate net_buf, hence we need to check that net_buf now to
determine if we need to wait for ACK or not.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This is the only use of the k_alert infrastructure in the Zephyr code
base. See whether we can get rid of it.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add mutex to lock STM32 I2C bus in order to guarantee
that data transfers are atomic and have exclusive access
to the bus.
Issue has been found fetching data from multiple sensors
on I2C bus in a mixed context of thread and triggered
interrupt.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lsm303dlhc_accel & lsm303dlhc_magn sensor driver to use new
defines so we can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Driver for networking device Microchip ENC28J60 is used as SPI slave,
moved to DTS type definition. Samples echo_client and echo_server use
this device on Arduino 101 board.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configuration of Erase command is specified in DTS. Hence
the corresponding changes in Kconfig are removed.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Number of sectors is now calculated from the flash density
i.e. (Flash size)/(sector size).
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
This patch enables the support for FLASH_PAGE_LAYOUT and
FLASH_MAP for the generic spin nor flash driver.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Use DT_ instead of CONFIG_ for spi freq, spi bus name, flash device
name and flash base address.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
The mcux lpuart shim driver was updated in commit
20202902f2 to use DT_ prefix in all
defined labels not related to Kconfig, but instance 2 was missed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fix the value for Low Power Enable (LP_EN) bit mask.
(Issue described by Coverity CID #188734)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Clean up a left over from GPIO driver factorization.
Definition of GPIO_REG_SIZE and GPIO_PORTS_BASE do not need anymore
to be spread accross SoCs.
Put these definitions directly in STM32 pinmux driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch adds a serial driver for the ARM PL011 IP block.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Modified drivers to use DEVICE_AND_API_INIT() instead of DEVICE_INIT()
This will make sure driver_api,is populated at build time and is exposed
to user space
Signed-off-by: Varun Sharma <varun.sharma@intel.com>
Renaming Kconfig.nrf5 to Kconfig.nrf in the wake of extending
the use of the nRF clock control driver to both nRF5 and nRF91
SOC series.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
