Added flags for controling detection of setting alarm to late.
Updated drivers to return -ENOTSUP when new option is requested.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Flags in alarm configuration structure will allow further extention
without breaking API. Initially, existing absolute flag was added
as the only flag.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Issue faced while running bluetooth sample (peripheral, central, ...)
on stm32wb55rg with the latest zephyr version
Signed-off-by: Roger N'Guessan <roger.nguessan@st.com>
Add clock support for STM32G0X SoC series.
Signed-off-by: Philippe Retornaz <philippe@shapescale.com
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add flash support for STM32G0X SoC series.
Signed-off-by: Philippe Retornaz <philippe@shapescale.com
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Cleanup around USB_NRFX_EVT_QUEUE_SIZE option.
Add value range for USB_NRFX_EVT_QUEUE_SIZE to Kconfig.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Use REQTYPE_GET_DIR and REQTYPE_GET_TYPE macros from
USB subsystem instead of specially introduced.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
flash_erase cannot erase a page from the STM32xx SOC flash. It seems
that the erase wait time is not enough and against to what the SOC's
datasheet states. As a result this patch doubles the wait time.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
Check the device state before nrfx_usbd_disable and
nrfx_usbd_uninit. Otherwise it may lead to an ASSERT
inside the HAL driver.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Do not use NRF_USBD_EP_NR_GET in ep_is_valid because
it masks the higher nibble. Although this behavior is valid
to get an index from an endpoint, it is not suitable to check
if the address is incorrect, such as: 0x11.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Check if the buffer size is not empty before spi transceive and buffer's
data processing. This fixes the need to slow down MCUs to 16MHz when
using BlueNRG-MS chips.
Tested samples : Beacon, Central, Peripheral
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Protect gpio_configure function in dual core context.
This operation is not needed for other fuctions of the api:
* init
* read
* write
Protecting gpio_configure also protects access to
interrupt_controller IP.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On STM32H7, in Dual core configuration, we restrict configuration
access to CM7 core. CM4 can access to API but not the init part of
the driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Provide basic clock control driver for STM32H7.
Bus clock activation is done through CM7 and CM4 common registers
so we don't have to care to the CPU Id before accessing.
Accesses are not protected for now. Only possible configuration
is system clock source set to HSE driven PLL.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support to STM LSM6DSO 6-axis IMU sensor driver.
This driver supports communication with device though both
I2C and SPI bus and both polling and drdy trigger mode.
This driver supports also the sensorhub mode with the possibility
to connect a maximum of two external devices, typically a
magnetometer and an environmental sensor, currently selected among
following devices: lis2mdl magnetometer, lps22hh or lps22hb
pressure and temperature sensors, HTS221 humidity sensor.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add support to STM LPS22HH pressure and temperature sensor.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The default tick rate is now 10 kHz, but that driver was demanding
that it be exactly 1 kHz instead of at least that rate. I checked the
source, and the driver isn't actually extracting "ticks" from the
kernel illegally, it just needs fine-grained timers that work with the
existing millisecond API. Let it build, this is fine.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
When the tick rate was less than MIN_DELAY, bumping a "too soon"
expiration by just one tick may not be enough and we could
theoretically miss the counter.
Instead, eliminate the MIN_DELAY computation and write to the spec:
NRF guarantees that the RTC will generate an interrupt for a
comparator value two cycles in the future. And further, we can test
at the set point to see if we "just missed" the interrupt (i.e. zero
cycles delay) and flag a synchronous interrupt. So we only need to
miss a requested interrupt now for the special case of exactly one
cycle in the future, and then we're only late by one cycle. That's
optimal.
Also fixes an off-by-one in the next cycle computation. By API
convention, an ticks argument of one or less means "at the next tick"
and not "right now". So we need to add one to the target cycle to
avoid incorrectly triggering a synchronous interrupt. This was a
non-issue when a tick is longer than a hardware cycle but is needed
now.
Also handles the edge case with zero latency interrupts (which are
unmaskable) which might mess up timing. This was always a problem,
but we're more sensitive now and it's comparatively more likely to
occur.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The MVIC is no longer supported, and only the APIC-based interrupt
subsystem remains. Thus this layer of indirection is unnecessary.
This also corrects an oversight left over from the Jailhouse x2APIC
implementation affecting EOI delivery for direct ISRs only.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This file is 32-bit specific, so it is moved into the ia32/ directory
and references to it are updated accordingly.
Also, SP_ARG* definitions are no longer used, so they are removed.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This commit changes the TX priority from ID based priority to
chronological order. The advantage is that when messages with
the same ID are sent, the order is retained.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Removed the STM32 CAN_Init function and implemented the initialization
in the driver.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Extended clock configuration to allow usage of external clock
source for nrf52 series.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Start es-wifi TCP server on accept.
An asynchronous (spi) message is received on client connection.
Only one connection is supported at a time.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
In order to prevent potential deadlock in various callbacks such as
accept, recv, etc... Add support for nested eswifi locking, allowing
callee to safely access back to the eswifi methods.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The eswifi controller can generate events via asynchronous messages
which can be polled via the 'MR\r' command. The messages will have a
Start Of Message Asynchronous [SOMA] and End Of Message Asynchronous
[EOMA] delimiters.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
