The USB_UART_CONSOLE option itself is not enough to enable console on
the USB UART port. Most of the code is actually shared with
UART_CONSOLE, so this symbol has to be selected.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Fix issue caused by 3fc497ac9a
This change removes `rtt` and `systemview` from header includes
as these are already placed in the path.
Also `SEGGER_SYSVIEW_ConfDefaults.h` header included from
`SEGGER_SYSVIEW_Int.h` is placed higher to make sure `INLINE`
definition is properly visible.
Signed-off-by: Pawel Dunaj <pawel.dunaj@nordicsemi.no>
L2 is the one who requests the packet to be sent, and not via net_if API
anymore. Stellaris driver was merged right after this behaviour change
and was thus lacking the proper modification.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Nordic devices detect edge interrupts through the PORT event which is
generated on a rising edge of DETECT, which itself is asserted when any
GPIO is configured for sense level detection and the GPIO's input signal
matches the configuration.
The previous code in Zephyr attempts to detect when at least one GPIO
SENSE signal is still asserted, and intentionally leaves the PORT event
uncleared to ensure the interrupt is re-entered.
This approach fails when no pin satisfies its SENSE condition during the
check but at least one input changes level between the completion of the
check and the clear of the PORT event. Such a failure can be observed
on the pca20020 hardware when multiple sensors configured for level
triggers are active. In this situation the corresponding sensor trigger
signals remain asserted but the PORT event required to drive their
processing has already been cleared.
The fix is to ensure that the SENSE configuration for all GPIOs across
all port instances is disabled prior to unconditionally clearing the
PORT event, then re-enabling the SENSE configuration for all GPIOs once
callbacks associated with detected SENSE triggers have been performed.
The act of re-enabling will ensure any relevant SENSE condition causes a
new rising edge on DETECT and so a new PORT event.
Closes issue #11806
See: https://devzone.nordicsemi.com/f/nordic-q-a/7246/missing-interrupts-on-gpioe-port-events
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The driver can be tested using different networking emulation
approaches.
This approach will work across multiple Qemu instances. There can be
more than one Qemu instance, run using the following command. They
would appear to be on the same Ethernet network.
$ qemu-system-arm -M lm3s6965evb \
-serial stdio \
-net nic \
-net socket,mcast=230.0.0.1:1234 \
-kernel zephyr.elf
This approach will work with other virtualization technologies that
support connecting to a VDE switch, like VirtualBox and User Mode
Linux. The switch can be started using the following command.
$ vde_switch --sock /tmp/switch
Qemu can be connected to the switch using the following command.
$ qemu-system-arm -M lm3s6965evb \
-serial stdio \
-net nic \
-net vde,sock=/tmp/switch \
-kernel zephyr.elf
Signed-off-by: Fadhel Habeeb <fadhel@zilogic.com>
Signed-off-by: Nirav Parmar <niravparmar@zilogic.com>
Signed-off-by: Vijay Kumar B <vijaykumar@zilogic.com>
The LFSTARTED event was disabled so it was impossible to wake the
CPU up on LF clock being ready. The Bluetooth stack was putting
the CPU to sleep, expecting to be woken up on LFSTARTED event.
As the event never triggered, the CPU was woken up seconds later
by a different event introducing a multi-second startup delay.
Bug introduced by 23c92100ac.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
SetAddress request (0x05) is ignored and not propagated, because it
is handled by nRF hardware. Curently, request type is not checked
causing class or vendor request 0x05 to be inappropiately ignored.
Only standard requests (type = 0) shoud be ignored. This commit
fixes the issue.
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
If gPTP is enabled, then enable also PTP clock driver so that
gPTP sync starts to work properly for native_posix board.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The PTP driver was init too late which prevented gPTP from
working in native_posix board.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch fixes the uart isr calling the callback with wrong data
(#11465) and the uart_poll_in checking the wrong status flag.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
A typo in the name of the bmRequest field in the nrfx_usbd_setup_t
structure was fixed in nrfx version 1.4.0. Update the driver to use
the new correct name: bRequest.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
If compiling with gPTP support for native_posix board, then avoid
compile error that is seen with gptp sample application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fragmented long CTRL OUT transfers does not work properly, because
they were not handler properly by the shim. In such transfers,
a special call (nrfx_usbd_setup_data_clear()) must be performed
before every data packet and not just before the first one.
This patch adds a byte counter which is set while processing setup
packet (host->device only) to be able to decide whether there will
be more data packets coming (and to call_data_clear() or not).
Fixes#11232 .
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
Add support for SoF events to the USB SAM device driver. When
CONFIG_USB_DEVICE_SOF is enabled, enable the corresponding interrupt
and call the callback function from there.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When running sanitycheck for reel_board which selects
CONFIG_NRFX_TWIM it fails the following tests:
tests/misc/test_build/test_newlib
tests/kernel/errno/kernel.common.errno.newlib
tests/lib/mem_alloc/libraries.libc.newlib
/zephyr/drivers/i2c/i2c_nrfx_twim.c:144:3: error: expected declaration
specifiers or '...' before '(' token
(bitrate == I2C_BITRATE_STANDARD ? NRF_TWIM_FREQ_100K \
^
/zephyr/drivers/i2c/i2c_nrfx_twim.c:151:3: note: in expansion of macro
'I2C_NRFX_TWIM_FREQUENCY'
I2C_NRFX_TWIM_FREQUENCY( \
^~~~~~~~~~~~~~~~~~~~~~~
/zephyr/drivers/i2c/i2c_nrfx_twim.c:184:1: note: in expansion of macro
'I2C_NRFX_TWIM_DEVICE'
I2C_NRFX_TWIM_DEVICE(0);
^~~~~~~~~~~~~~~~~~~~
/zephyr/drivers/i2c/i2c_nrfx_twim.c:154:3: error: expected declaration
specifiers or '...' before string constant
"Wrong I2C " #idx " frequency setting in dts"); \
^
/zephyr/drivers/i2c/i2c_nrfx_twim.c:184:1: note: in expansion of macro
'I2C_NRFX_TWIM_DEVICE'
I2C_NRFX_TWIM_DEVICE(0);
^~~~~~~~~~~~~~~~~~~~
zephyr/drivers/i2c/CMakeFiles/drivers__i2c.dir/build.make:62: recipe
for target
'zephyr/drivers/i2c/CMakeFiles/drivers__i2c.dir/i2c_nrfx_twim.c.obj'
failed
To fix this, let's replace the use of static_assert() with a more
generic macro: BUILD_ASSERT_MSG() This should work across minimal
libc, newlibc and c++.
Signed-off-by: Michael Scott <mike@foundries.io>
As for Ethernet, up to ieee802154 L2's send to actually sent the packet.
It's currently unoptimized as 6lo compression, 15.4 fragmentation and so
on will reallocate net_buf etc... but it's the first step towards
removing ll reserve space and more.
Applying changes to Openthread L2 as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now instead of such path:
net_if_send_data -> L2's send -> net_if tx_queue -> net_if_tx -> driver
net_if's send
It will be:
net_if_send_data -> net_if tx_queue -> net_if_tx -> L2's send -> driver
net_if's send
Only Ethernet is adapted, but 15.4 and bt will follow up.
All Ethernet drivers are made compatible with that new scheme also.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The sensor signal cannot be cleared by the application, so enabling
level triggers causes the system to hang as the callback is invoked
repeatedly. We want notification when the alarm state is entered, and
when it's exited, so use a double edge.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add symbolic names to bus type (LIS2DH_BUS_TYPE) and trigger mode
(LIS2DH_TRIGGER_MODE) in order to be defined in board defconfig
files.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lis2dh accelerometer driver to get the device name as well
as i2c/spi slave information from device tree. Updates the build_all
test accordingly. (issue #11605)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Two subtractions failed to account for the possibility that a calculated
time exceeded the counter resolution, allowing a comparison to
improperly indicate that a minimum delay was satisfied.
Use the subtraction helper to avoid the problem.
(The subtraction in z_clock_set_timeout was the cause of issue #11694;
the one in rtc1_nrf5_isr was replaced based on inspection rather than
testing.)
Closes#11694
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
poll_out function was returning the character that was sent. It
happens that it is always constant and the return of this functions is
never tested. Changing it to be a void function.
MISRA-C rule 17.7
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The comment was incorrect explaining why we were sending an
AT-command without waiting for a response (via a K_NO_WAIT timeout).
Let's correct the comment and avoid confusion.
Signed-off-by: Michael Scott <mike@foundries.io>
Remove overly complicated logic to skip incoming data if we were
still waiting on a previous set of data to be read.
This fixes a bug where an error during data receive could end up
with the modem ignoring all incoming data.
Signed-off-by: Michael Scott <mike@foundries.io>
Remove an unnecessary local variable to store the
return value, instead return directly thereby saving
few bits of memory.
Found using Coccinelle.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Remove an unnecessary local variable to store the
return value, instead return directly thereby saving
few bits of memory.
Found using Coccinelle.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Fixed the return values for read and write APIs for spin_nor.c
which were not inline with what the corresponding interfaces
were meant to return.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Current implementation had fixed initial speed, this commit
fixes TWI and TWIM shims to use configuration from DTS.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Coverity complains that packet_len can get assigned a negative value if
usb_dc_ep_mps() returns an error. This is correct, however it only
happens if the endpoint address is invalid, and in that case the value
is not used as the endpoint address is also validated in
usb_dc_ep_write().
Fix the issue by moving the assignment after the endpoint address
validation and by accessing the value directly instead of getting it
through usb_dc_ep_mps().
Fixes#11481
Coverity-CID: 189742
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Start of Frame events can now be accessed from USB classes.
This will be useful when implementing idle rate functionality.
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
Implements setsockopt() for the socket offload driver
to process the TLS tags sent in via the Zephyr setsockopt() API,
when CONFIG_NET_SOCKETS_SOCKOPT_TLS is chosen.
For each tag, the credential filenames are retrieved and
set via SimpleLink's sl_SetSockOpt() API.
Also, creates a new KConfig option for TLS_CREDENTIAL_FILENAMES.
This new option is used by apps/protocols to add TLS credentials
via filenames referring to the actual content stored on a secure
file system or flash.
Handles the IPPROTO_TLS_* socket protocol families in the
socket() offloaded API.
This was validated on the cc3220sf_launchxl with the http_get sockets
sample, with the globalsign_r2.der file loaded to secure flash via
the TI Uniflash tool, and using the TI Catalog of known good
root CA's.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
