When CLOCK_CONTROL_NRF_FORCE_ALT is enabled then calibration is
performed outside of the driver. In that case certain Kconfig
options where present which were dedicated for case when calibration
is performed by the driver. Side effects of those options lead to
conflicts when CLOCK_CONTROL_NRF_FORCE_ALT was enabled. Fixed
those conflicts by introducing Kconfig option which indicates
whether calibration is performed by the driver or not.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Model descriptions in Kconfig.ssd1306 should be ssd1306 instead of
ssd16xx, these may be copied from driver for ssd16xx.
Signed-off-by: Huang Qi <no1wudi@qq.com>
- Per datasheet (Rev 1.0, Page 29): When enabling adv_power_save, there
needs to be a 1ms inter-write registers delay. With this addition, the
driver will work at SCLK frequencies faster than 100kHz.
- Added helper function reg_write_with_delay() to factor these writes.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Updated uart_rx_enable() and uart_tx() to use timeout given
in microseconds. Previously argument was given in milliseconds.
However, there are cases when milliseconds granularity is not
enough and can significantly reduce a throughput, e.g. 1ms is
100 bytes at 1Mb.
Updated 4 drivers which implement asynchronous API. Updated
places where API was used.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Replaces the prefixes of gpio_matrix_in and gpio_matrix_out
to unify those function calls on all supported socs.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
When the driver was called to set the period length for a channel
to 0, it set the COUNTERTOP register in the PWM peripheral to 0,
what resulted in an undefined behavior of the peripheral (and lack
of the STOPPED event sometimes).
The PWM API does not precise how should a zero length period be
handled; some drivers return the -EINVAL error in such case, some
do not. This patch fixes the pwm_nrfx driver so that it does not
change the previously used COUNTERTOP register value when the period
length is set to 0, and because the pulse cycles are always limited
by the driver to period cycles (so 0 in this case), in result the
relevant channel is simply deactivated. This allows users to switch
off a channel by requesting the pulse width to be set to 0 without
providing a non-zero period in such call.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Implement the CPU idle task. The system should enter this task when
there is no any task to ensure power saving.
Tested on it8xxx2_evb board. It will reduce 12.5mA when system enters
the CPU idle task.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
STM32G0/F0 SoCs allow to remap PA11/12 to PA9/10. Some boards
were manually configuring this remap. This patch centralizes this
functionality to the pinmux driver, allowing boards to enable the
remap directly in board dts file.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When existing stop mode 1&2, VCO is set to range 4
and should be set back to range 1 to allow full speed
operations.
Rather than setting VCO at startup, set it inside clock
setting procedure so that it could done
in clock reset procedure when existing stop modes.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
If CONFIG_WIFI_ESP_AT_SCAN_MAC_ADDRESS: mac addr included in
scanning results.
if CONFIG_WIFI_ESP_AT_SCAN_PASSIVE: passive scanning is used instead of
default active scanning.
If CONFIG_WIFI_ESP_AT_SCAN_RESULT_RSSI_ORDERED: scanning response
ordered by RSSI.
Signed-off-by: Jani Hirsimäki <jani.hirsimaki@nordicsemi.no>
On LSM6DSO sensor the INT1 pin is used for both generating the drdy
interrupt and for switching to I3C hotjoin mode just after reset if
it is at logical '1' level. It might happen that after a board
reset the logical level '1' is preserved (maybe a level shifter)
forcing the LSM6DSO to enter erroneously in I3C mode, breaking any
attempt to communicate with it. (Fix#38902)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This kconfig is only used for one board and is simply an alias
to another kconfig. So remove CONFIG_DW_ICTL_OFFSET and apply
the value directly to the other kconfig.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Uptime in milliseconds is assigned to uint32_t variable, which results
in integer overflow after enough time has expired. Additionally
milliseconds part (which should be 0-999) is assigned directly from
uptime, without subtracting full seconds.
Fix both issues by using int64_t variable and calculating milliseconds
with modulo.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Convert all CS control logic to be based on the `gpio_dt_spec` member
instead of the standalone `port`, `pin` and `flags` members.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Co-authored-by: Jordan Yates <jordan.yates@data61.csiro.au>
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
Co-authored-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
async_rx_disable does not re-anable RXNE interrupt, it was disabled
during async_rx_enable
Signed-off-by: Manojkumar Subramaniam <manoj@electrolance.com>
Removing two unused "struct fdc2x1x_data" to fix warnings
when compiling with PM_DEVICE=y.
Signed-off-by: Igor Knippenberg <igor.knippenberg@gmail.com>
All ARC CPUs (supported by Zephyr) don't lose core interrupt
controller configuration after switching to sleep mode / modes,
so we don't need to save & restore it's configuration with PM.
This PM code most likely was added for Arduino 101 (Genuino 101)
board which isn't supported by Zephyr anymore - so we can drop
it.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
We don't use '_VectorTable' in the driver, so let's drop it's
declaration.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
In some configurations (e.g. edge interrupt triggers),
an interruptible event occurs during ISR and the host interrupt
controller does not see the new event due to IIR is constantly
asserting interrupts. For example, the callback handles RX and
then TX. If another character comes in before end of TX processing
(TX interrupt still asserts while raising RX interrupt), the host
interrupt controller may not see this new event. So if needed,
the IER is being toggled to re-assert interrupts at the end of ISR
to nudge the host interrupt controller to fire the ISR again.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove Kconfig options for enabling device instances in favor of
taking that information only from device tree. Prior to that
change there was a mix of devicetree and Kconfig.
Bring back use of CONFIG_GPIO_NRF_INIT_PRIORITY.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Allow the user to register function callbacks that
are executed during gsm modem configuring and stopping.
Signed-off-by: Bartosz Bilas <bartosz.bilas@hotmail.com>
GPIO L/K groups:
On IT81202 (128-pins package), the pins of GPIO group K and L aren't
bonding with pad. So we configure these pins as internal pull-down
at default to prevent leakage current due to floating.
GPIOH7:
On IT81202/IT81302, the GPIOH7 isn't bonding with pad and is left
floating internally. We need to enable internal pull-down for the pin
to prevent leakage current, but IT81202/IT81302 doesn't have the
capability to pull it down. We can only set it as output low,
so we enable output low for it at initialization to prevent leakage.
After setting: power saving=2.26mA
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The magnetometer on the LSM303DLHC has a different gain conversion
factor for LSB to Gauss for the Z axis than it does for X, Y. This
commit takes into account the different conversion factors, and
adds the correct coefficients for each gain setting and axis.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
This constraint on the AHB prescaler is removed.
The ahb-prescaler is allow from 1-512.
For stm32 common and stm32U5 devices.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Remove APIs used in the pre-DT era. In case manual access is required,
`stm32_dt_pinctrl_configure` can still be used as a shortcut with data
initialized in the expected format.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Fixes: #38959
Currently, the I2C driver returns I2C status register value as error
code when error happen. This PR fixes returning system number and
the return values is negative for error.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
Change the REMAP bits of the AFIO_MAPR of the stm32F1x soc
with local MACRO without changing the SWJ_CFG (write-only bits).
The serial wire JTAG configuration is taken from the Z_AFIO_REMAP
(value of the CONFIG_GPIO_STM32_SWJ_xxx))
and not read from the MAPR register.
It accesses to the MAPR register directly instead of LL functions.
Note that Remapping on the MAPR2 is not to change.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Timer STM32 LPTIM currently supports 2 clocks sources: LSE & LSI.
LSE (external) is defined as default but its availability depends
on board support package and then may not be available.
This ends up in situations where users have LSE implicitly selected
while no crystal is available on board, leading to non functional
LPTIM.
To avoid this situation, makes LSI clock, which is always available
(since internal to the SoC), the default LPTIM source clock.
Then, default case will be functional. Users will then be able to
select LSE if needed.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Some functions were being re-defined as macros if certain conditions
were not met.
Fix violations to rule 5.5
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
console_input_init is only used in the same scope it is implemented.
There is not need to have it defined elsewhere.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
interrupt controller, also places its relevant
peripheral sources allowing drivers to use the
DT macros instead of espressif headers.
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
Changes the modem_context_sprint_ip addr to write into a provided
buffer. This approach fixes a referencing to a non existing stack
variable, without using a lot of stack space.
Tested using the by building all used modems and tested on HW using
IPv4.
Fixes: #38459
Signed-off-by: Sjors Hettinga <s.a.hettinga@gmail.com>
