Move pixel format setting (RGB565/RGB888) to DeviceTree. Add support for
changing pixel format at runtime.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Multiple enhancements towards better code readability and consistency:
- sorted headers
- define and reference magic constants
- adjust some names
- add U suffix to unsigned constants
- move hw reset to a function
- remove non-needed initialization code from seeed tft
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Adds imx rt support.
Allows n-number of can interfaces based on device-tree.
Adds a "common" irq name.
Added CAN bus pins and dts for 1060 and 1064 EVK.
Signed-off-by: Rick Talbott <rtalbott@fastmail.com>
This enables support for the confgure and config_get functions in
the UART API, allowing users to change baudrate, parity, stop bits,
data bits and flow control in runtime.
Signed-off-by: Jesper Derander <jesper.derander@endian.se>
Add additional pinmux definitions for I2C1 and I2C2 that are used
on the stm32f030 series SoCs. Additionally, correct the PF0 and PF1 I2C
functions, which were swapped.
Signed-off-by: Brian Kubisiak <brian@kubisiak.com>
Reset rx byte counters when hw timer/counter is disabled.
Fixes issue where disabling and re-enabling async uart rx can produce
"UART_RX_RDY" events with invalid data when power management is used.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
The condition used to detect presence of optional devicetree
properties that specify read and write opcodes was inadvertently
changed to something that will never be true. Update the check and
the property extraction to restore the original behavior.
Fixes#28635.
Signed-off-by: Stephan Walter <stephan@walter.name>
The ce0cc3a7 commit (lsm6dsl: make the driver multi-instance) changes
all bus API signature, which now requires a "const struct device *dev"
and not a "struct lsm6dsl_data *data". By mistake the shub part was
left unchanged. Fix: #28565
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Algorithm for waiting for clock stabilization was failing in case when
it was waiting for clock availablity and clock was already available
before function was called. That is because nrfx_clock_is_running
was returning false because XTAL was already started but not yet
running.
Added a check for current LF source, if XTAL is picked that indicates
that RC is already running because of two stage startup procedure.
Added documentation of lfclk_spinwait with explanation of two stage
approach.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Initialize device pointer in driver's context.
It was not done quite right in commit a1708cf2f2
("drivers: ethernet: Fix device instance const qualifier loss"),
and then completely removed in commit 113d9274ea
("drivers: ethernet: remove stray expression")'
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This commit fixes the following issue:
When using slip without TAP, i.e. CONFIG_SLIP_TAP=n (default), while
another ethernet interface is enabled and sets CONFIG_NET_L2_ETHERNET=y.
This causes ethernet_init() to be wrongly called with struct dummy_api
instead of struct ethernet_api.
ethernet_init() expects struct ethernet_api (by cast), so we end up
with the get_capabilities field pointing to garbage!
Actually, as we are using the dummy api, we don't need to call
ethernet_init() at all.
Sole dependency on CONFIG_NET_L2_ETHERNET is wrong because it
can be enabled by another interface.
Signed-off-by: David Komel <a8961713@gmail.com>
Named choice is needed in order to be able to extend it
in other modules.
Closes: #28559
Signed-off-by: Ievgenii Meshcheriakov <ievgenii.meshcheriakov@nordicsemi.no>
* Add missing the PINMUX macros for UART5 pins.
* Correct a typo in STM32F1_PINMUX_FUNC_PC5_ADC12_IN15; the macro
used PC4 instead of PC5 for ADC12_IN15.
Signed-off-by: Paul Fagerburg <pfagerburg@google.com>
HAS_DTS_I2C is now selected by I2C and
always used as I2C && HAS_DTS_I2C.
It could then be purely removed.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The correct return value is -ENOBUFS if we run out of network
buffers when sending the packets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add BT_QUIRK_NO_AUTO_DLE quirk option for HCI rpmsg driver
when the Zephyr open source BLE controller is used.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix the error recovery mechanism that makes use of a temp variable
to avoid coverity issue without breaking error recovery.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Function spi_context_longest_current_buf() has been introduced in
commit ddef35c1da for the purpose of
getting the longest possible (potentially partial) SPI transfer
for which all currently active directions have a continuous buffer.
Such transfer can be done with taking advantage of a DMA that cannot
use scattered buffers (and this is the case for nRF SPI drivers with
which this function has been introduced).
Unfortunately, because of its inadequate name, later on this function
has been incorrectly used in other SPI drivers for getting the longer
of TX/RX buffers. And commit afc480f12b
recently "fixed" the implementation of this function, assumably to
adjust it to those incorrect uses, but this way it has also broken
the nRF SPI drivers.
Instead of restoring the original implementation of the function in
question, this commit adds a new one with functionality equivalent
to that original but with a hopefully less misleading name, and this
function is used in the nRF SPI drivers.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Isochronous transactions do not support handshake phase
so in particular the ISO endpoint cannot be STALLed.
Isochronous transactions do no support data toggle sequencing
and should only send DATA0 PID.
Taking into consideration those requirements do not try to
clear dtoggle or STALL an ISO Endpoint in nRF USBD driver.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
The pull request #26269
drivers: SPI: Adds CS flags from devicetree
missed out on the APA102 led_strip driver, most likely due to the driver
not utilising the chip select signal until #25310
drivers: led_strip: Add support for external SPI CS on APA102 LED strips
Signed-off-by: Roman Vaughan <nzsmartie@gmail.com>
Enable by default the use of RAM buffers in the spi_nrfx_spim.c
driver for copying TX data located in flash (as SPIM peripherals
cannot transfer directly form flash). Without this patch, users can
get confused, especially when SPI transaction is used by an upper
level driver which does not check all error codes.
For size of the buffer, use the value used so far in the reel_board
default configuration and in the SPI loopback test, i.e. 8 bytes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Not possible to use device_get_binding() because we are
currently initializing DMA_1 device, so it is not ready and
device_get_binding() will fail.
Directly use string compare is more efficient.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Pins used for external LF clock source must be configured as
used by peripheral to allow using LFXO on network side.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Reimplement getaddrinfo to call SlNetUtil_getAddrInfo from the TI HAL
for a more robust implementation that supports both client and server
modes, and performs better error-checking.
Fixes#11890
Signed-off-by: Vincent Wan <vwan@ti.com>
Fixes#28275 by adding bluetooth HCI spi driver priority lower
(75 instead of 50) than SPI (70) to avoid device_get_binding
to return NULL because the device was not initialized.
Signed-off-by: Jeremy LOCHE <lochejeremy@gmail.com>
Enabled going to idle when waiting for low frequency clock.
Added 2 stages of starting LF clock when XTAL is used. First
stage is starting RC and then when it is ready XTAL is started.
It is done to get event/interrupt when RC is ready which means
that LF clock is available (but not stable).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Added configuration for approach to starting system clock source.
There are 3 options: no wait, wait untill available, wait until
stable.
Added support for those modes in clock control driver which handles
low frequency source clock.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The driver is able to write with 32-bits word alignment of size
and offset, apart form sub-word writes for which it can write
part of word to aligned offset (which is a hack).
fixes#26729
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Use setting from devicetree to drive the default setting for
CORTEX_M_SYSTICK. We update the dts files to default systick to be
enabled since the major of cortex-m platforms utilize it by default
(except on Nordic SoCs, TI CC13x2/CC26x2 and MEC1501 in which we
default to disabled).
Fixes#25299
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename wdog_cmsdk_apb_enable to wdog_cmsdk_apb_setup,
this API is supposed to be called during driver probe based on
CONFIG_WDOG_CMSDK_APB_START_AT_BOOT (enabled by default).
Fixes: 03c7d9bd49 ("drivers: wdog: Update CMSDK Wdog driver")
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
"unused value" issue reported by Coverity (CID: 214211).
This is actually a true bug as reported error is erased
and not taken into account.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
