Updated the driver to support low power mode.
Introduced "enable-low-power" flag in device tree to
control(on/off) low power mode.
If flag added in DTS, during sleep BBLED will switch off the LEDs.
Otherwise BBLED will continue the configured blinking pattern on LEDs.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Add support for resetting controller at boot, and update FT5336
documentation to indicate that the FT3267 IC is also supported by this
driver.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for RM67162 MIPI display controller. This controller
is configured to run in MIPI command/DBI mode, driving a 400x392 OLED
display.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fix support for DCS long write command in DSI mcux driver, to enable use
with displays that require this command for full support.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Only setup DPI input from LCDIF if MODE_VIDEO is set, as this
is the the only case where input from the LCDIF would be required to
drive the display. Do not populate the dpi_config structure unless a
reference the the NXP LCDIF device is provided, since this is the output
device providing DPI data.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fixup support for DCS_LONG_WRITE command in DSI MCUX 2L driver. Since long
DCS commands may benefit from nonblocking I/O, add support for non blocking
transfers to the DSI driver.
This commit also corrects the interrupt number for the RT595, which uses
the DSI_MCUX_2L IP block.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Make DPI mode an optional configuration for the DSI MCUX 2L driver.
DPI mode will only be enabled when the MIPI is attached in video mode,
since this is when DPI formatted packets are expected.
This will enable the DSI driver to also support DBI/command mode, for
displays that use this format.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add DSI video mode flag to MIPI configuration, to indicate to MIPI
drivers that this display uses video mode and must be refreshed
constantly.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Implement a driver for the PWM controller MAX31790. This driver
also implements the RPM mode of the controller, which can
be accessed via setting pwm_flags_t accordingly to macros
defined in the driver specific header.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Fix a build error introduced in 9f02eeadf8, the async pointers are only
available when UARTE_ANY_ASYNC is set.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
STM32F1 series RTC is not compatible with other STM32F1 series,
and it uses a different LL API.
Current implementation of the driver doesn't take this into account,
so we need to explicitly exclude STM32F1 series support until
some changes are made.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Define only once the CRYP_DATATYPE_8B for the stm32h5 serie
This macro is in modules/hal/stm32/stm32cube/stm32h5xx/d
rivers/include/stm32h5xx_hal_cryp.h
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Previously, only a single type of ADCs was always available
in the ADC shell. This change enables the usage of the ADC
shell for different ADC types at the same time.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
This puts a ifdef guard around the inclusion of ACPICA header
file. The ACPICA module is not active unless CONFIG_ACPI is
also enabled so we should not be using that header without
CONFIG_ACPI also being enabled.
This was discovered by Coverity.
Fixes#60484
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a check of the return of clock_control_get_rate(),
and returns error in uart_configure() if unsuccessful in
getting clock rate.
Fixes#60478
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Interrupt callbacks may want to configure GPIO pins on the port expander,
e.g. to change the polarity of a level interrupt. This would cause a
deadlock because the callback handler would still be holding the lock.
Signed-off-by: Armin Brauns <armin.brauns@embedded-solutions.at>
This adds the CONFIG_UART_USE_RUNTIME_CONFIGURE guard to
disable the API function pointers if the kconfig is not enabled.
Both .configure and .config_get should only be usable if runtime
(re-)configuration of UART is needed.
Ifdef guards are added to drivers previously lacking this guard.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
When building the driver for efr32bg27_brd2602a none of the condition
matches and the compiler warns for:
hwinfo_gecko.c: In function 'z_impl_hwinfo_get_reset_cause':
hwinfo_gecko.c:38:18: warning: unused variable 'rmu_flags'
38 | uint32_t rmu_flags = RMU_ResetCauseGet();
This fails the bi-weekly build, add a __maybe_unused to silence the
warning.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This fix a build issue where ICM42688_DECODER is enabled but
SENSOR_ASYNC_API is not, which results in some structures in an
orphan section:
warning: orphan section
`._sensor_decoder_api.static.invensense_icm42688__decoder_api_' from
`libdrivers__sensor__icm42688.a(icm42688_decoder.c.obj)'
being placed in section
`._sensor_decoder_api.static.invensense_icm42688__decoder_api_'
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Use a combination of sys_cpu_to_be16 and i2c_burst_write_dt for setting
16 bits registers. Get rid of a bunch of temporary variables, custom
conversions and few bus writes.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The current ID for BQ274XX_DEVICE_ID is actually the one for the
BQ27421. The driver seems to work with the BQ27427 as well, at least the
common and extended commands are the same, so add that variant as well,
rename the existing one and print the currently read ID when the ID
check fails.
The configuration registers have a different offset though, so add a
register offset table and make the device rcognize the right one un
runtime based on the device ID.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Use i2c_reg_write_byte_dt instead of bq274xx_cmd_reg_write. The wrapper
does not add anything anyway.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Change bq274xx_sample_fetch to support SENSOR_CHAN_ALL. This makes it
possible to get the sensor data using the sensor shell, besides being
generally convenient.
Also drop a redundant comment.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The device technical reference manual says "The Sealed to Unsealed key
has two identical words". Use two different defines with the same value
in the code so it's somewhat less ambiguous that the double write is
intentional.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add a retry count limit to config update mode loops, this way the system
can still boot if there's an issue with the device. The normal sleep
should be enough for correct operation, adding a conservative limit.
Rework the delays to be unambiguous while at it.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Fix the calculation for designenergy_mwh, as right now it's using a
float casted straight to an int, which results in the factor rounded
from 3.7 to 3. Also rework both that and taperrate so that they don't
use floating point.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Control reg write seems to support two bytes mode (the technical
reference shows example of that), so use a single i2c_write_dt there.
Also drop a couple alias variables from bq274xx_cmd_reg_write.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add the bq274xx_ back to the static function prefixes for the bq274xx
driver.
These have been removed recently but every other sensor and most Zephyr
driver have static function prefixed, this helps avoiding ambiguity in
list files, stack traces, setting debugging breakpoints etc.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Added a parameter inside the Channel Number macro since
the LPC55S36 expects an address rather than a static number.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
LL name for PLL1Q is not the same across STM32G0, STM32WL, STM32H5 and
STM32H7 families. This allows to choose the proper definition depending on
the family.
Signed-off-by: Johan Lafon <johan.lafon@syslinbit.com>
memcpy of a sub-structure in a structure was using the structure size
of the parent structure instead of the sub-structure.
fixes: #59548
Signed-off-by: David Leach <david.leach@nxp.com>
Enabled support for is31fl3733 driver. This driver supports
the full LED API, and enables the following features of the is31fl3733:
- individual LED dimming
- individual LED enable/disable
- bulk writes of LED enabled and dimming states
- global LED current limit
- blanking (via custom API)
Signed-off-by: Daniel DeGrasse <daniel@degrasse.com>
Add Nuvoton numaker series flash memory controller(FMC) with erase,
read & write features of soc-flash. Also update Nuvoton manifest
to include zephyrproject-rtos/hal_nuvoton#6.
Signed-off-by: cyliang tw <cyliang@nuvoton.com>
channel_pos_read bit was being cleared with a sensor channel enum value
instead of the encoded bit position.
Signed-off-by: Al Semjonovs <asemjonovs@google.com>
Forcing the usage of the RC oscillator and keeping it on turns out
to have detrimental effects to the readings by default. The default
clock mode settings are perfectly fine.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Use generic symbols defined in ieee802154.h for packet/FCS size instead
of redefining them in the driver header.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In case upper layer does not follow the convention, and the net_pkt
provided to the nRF 15.4 driver had a payload larger than the maximum
payload size of an individual 15.4 frame, the driver would end up with
buffer overflow.
Fix this by adding an extra payload_len check before attempting to copy
the payload to the internal buffer.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This CL attempts to implement npcx's flash driver instead of the
original one (npcx spi driver plus spi_nor flash driver).
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Add a new pinctrl type to control peripheral modules' specific IO
characteristics such as tri-state, the power supply type selection (3.3V
or 1.8V), and so on. In NPCX series, the corresponding registers/fields
are irregular. This CL wraps these definitions to dt nodes and put them
in pinctrl property if needed.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
