Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options for UART instances.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Adding port information for uart tx and rx pins in dts, so that it can
be more systematically retrieved in the uart driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Although it is not clearly specified in the UART API, this function
is supposed to return 0 when the TX interrupt is disabled, regardless
of whether anything could fit into the TX buffer or not (this can be
concluded from looking at implementations of several samples and tests
present in the tree, also almost all UART drivers are implemented this
way).
The problem in the uart_nrfx_uarte driver case is that the flag that
allows generation of the TX interrupt is not cleared directly in the
uart_irq_tx_disable() function but this clearing is deferred to the
end of the current transmission, in case one is in progress, and hence
it is done in the interrupt handler. Consequently, when the interrupt
handler is not entered between calls to uart_irq_tx_disable() and
uart_irq_tx_ready() (e.g. when both functions are called in a loop
executed in the interrupt context), the latter may return an invalid
value.
Fix this problem by additionally checking if the TX interrupt was
requested to be disabled, not only if it is already disabled in
hardware.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-uart binding for dma to replace the rxdma and txdma
properties with proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The driver was extended so that the tests/drivers/uart/uart_basic_api
test case now passes. The following modifications were made for the
following items of the test case:
* test_uart_configure
* test_uart_config_get
The driver was missing the support to re-configure the UART at run-time
as well as to obtain the current configuration at run-time via the
.configure and .config_get hooks provided within the UART driver API.
For the flow control setting, bit (mask) definitions were added for the
Modem Control Register. Both the configuration get and set functions
come with auxiliary functions that convert configuration register bit
masks to the UART driver API's enumeration types and vice versa.
For run-time configurability, the device's data struct is required un-
conditionally, previously, it was only available whenever interrupt-
driven mode was enabled. Consequently, the device initialization was
simplified to a single call of the DEVICE_AND_API_INIT macro, as the
existance of the device's data struct is now no longer conditional.
* test_uart_fifo_fill
For the user callback function of the test case to receive the initial
'Ready to TX' indication upon which the TX FIFO is filled, it is
necessary that uart_xlnx_ps_irq_tx_enable also sets the TX FIFO empty
bit in the Interrupt Enable Register. Consequently, the same modifi-
cation applies to the irq_tx_disable function.
* test_uart_fifo_read
During inital device configuration, the RX FIFO interrupt trigger
level has to be set to 1 byte for now, as the test case doesn't poll
the incoming data in a while()-loop, therefore, it misses the CR/LF
if more than one character is in the RX FIFO at the time of the
interrupt and neither CR nor LF is the first character.
Whenever the state of an interrupt is checked by the user callback
function (uart_xlnx_ps_irq_tx_ready, uart_xlnx_ps_irq_rx_ready),
the corresponding bits are cleared in the Interrupt Status Register,
re-enabling interrupts generated by the corresponding source.
Tested on QEMU (R5, A9) and actual Zynq7000 hardware.
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
Added the SERIAL_SUPPORT_INTERRUPT feature flag to the driver's
configuration file. This flag was missing, although the driver
supports interrupt-driven operation.
Interrupt support is required for testcases using the UART_PIPE
feature on the upcoming Cortex-A9 targets (QEMU/Zynq-7000).
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
Fix for the UART_XLNX_PS_IRQ_CONF_FUNC macro, which wraps IRQ_CONNECT
into a function for each device instance. This macro had device
instance #0 hardcoded at one point.
Interrupt support is required for test cases using the UART_PIPE
feature on the upcoming Cortex-A9 targets (QEMU/Zynq-7000).
Signed-off-by: Immo Birnbaum <Immo.Birnbaum@weidmueller.com>
In some cases (eg at high baud rate, no HW flow control, and when BLE
radio/ints running) data could be lost between when enough characters
have been RX'd to fill the DMA buffer and when the ENDRX event was
fired, where the the STARTRX task is invoked to start filling the next
buffer (which is set up earlier, but I think will not be filled until
STARTRX).
To fix this, the SHORT is enabled between ENDRX and STARTRX whenever the
'next' buffer is available, so that STARTRX is invoked automatically and
subsequent chars go into the next buffer via EasyDMA.
To make this work properly, uarte_nrfx_isr_async() now handles the ENDRX
event _before_ the STARTRX event.
There was also an issue in rx_timeout() where the received character
count (rx_total_byte_count) could be incremented greater than the actual
buffer size. This arises from rx_total_byte_count value coming from the
counting the RXDRDY events (either by PPI/timer counter or counting the
RXDRDY ints themselves) and so if chars are received in the rx_timeout()
(or before ENDRX is handled) the rx_timeout() could increment rx_offset
past the length of the buffer. This could result the remaining 'len'
being calculated incorrectly (an underflow due to unsigned - signed ,
where signed > unsigned).
To fix this, we now store the lengths of the buffers and don't invoke
the UART_RX_RDY callback when the buffers are full; its handled by
ENDRX.
(Also note that the buffer size should be available via the RXD.MAXCNT
register on the nrf, but this register is not exposed through the nrfx
HAL and is also double buffered, so it seemed clearer to just track the
buffer lengths explicitly here in the driver).
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
for fixup
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
When we build this driver with CONFIG_UART_ASYNC_API enabled we get the
following build error:
uart_sam0.c: In function 'uart_sam0_init':
uart_sam0.c:558:35: error: redefinition of 'dev_data'
558 | struct uart_sam0_dev_data *const dev_data = DEV_DATA(dev);
uart_sam0.c:498:35: note: previous definition of 'dev_data' was here
498 | struct uart_sam0_dev_data *const dev_data = DEV_DATA(dev);
Fix this be removnig the duplicate at line 558.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Avoid entering an infinite loop when configuring the the NXP Kinetis
LPUART IRQ.
Fixes 9a65318a5b.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Reworked usart_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked uart_sam driver to utilize new DT_INST macros as part of this
rework we also now get pin ctrl/mux configuration information from the
device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The UART driver for samd0 was is missing the .configure and
.config_get functionality expected from api for serial driver.
This commit fixes this by providing basic configuration
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Make I2C and SPI drivers for nRF SoCs no longer dependent on Kconfig
options that enable instances (i.e. I2C_x and SPI_x). Now these drivers
enable hardware instances when corresponding nodes in devicetree are
enabled (have status "okay").
For I2C, SPI, and UART drivers, instead of using Kconfig dependencies
to prevent enabling of hardware instances that cannot be used together
(e.g. SPIM1 and TWIM1), a file that signals invalid configurations with
build assertions is added to compilation.
Also dependencies on HAS_HW_NRF_* options are removed from Kconfigs
of I2C, SPI, and UART drivers, as for hidden options that activate
proper type of driver such dependencies are not actually helpful.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `UART_x_NRF_UART*` that select
the type of nrfx driver (for UART or UARTE peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding UART node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between UART and UARTE for a given instance.
Since all `UART_x_NRF_UART*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert older DT_INST_ macro use in arm_cmsdk/arm drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a k_timeout_t type, and use it everywhere that kernel API
functions were accepting a millisecond timeout argument. Instead of
forcing milliseconds everywhere (which are often not integrally
representable as system ticks), do the conversion to ticks at the
point where the timeout is created. This avoids an extra unit
conversion in some application code, and allows us to express the
timeout in units other than milliseconds to achieve greater precision.
The existing K_MSEC() et. al. macros now return initializers for a
k_timeout_t.
The K_NO_WAIT and K_FOREVER constants have now become k_timeout_t
values, which means they cannot be operated on as integers.
Applications which have their own APIs that need to inspect these
vs. user-provided timeouts can now use a K_TIMEOUT_EQ() predicate to
test for equality.
Timer drivers, which receive an integer tick count in ther
z_clock_set_timeout() functions, now use the integer-valued
K_TICKS_FOREVER constant instead of K_FOREVER.
For the initial release, to preserve source compatibility, a
CONFIG_LEGACY_TIMEOUT_API kconfig is provided. When true, the
k_timeout_t will remain a compatible 32 bit value that will work with
any legacy Zephyr application.
Some subsystems present timeout (or timeout-like) values to their own
users as APIs that would re-use the kernel's own constants and
conventions. These will require some minor design work to adapt to
the new scheme (in most cases just using k_timeout_t directly in their
own API), and they have not been changed in this patch, instead
selecting CONFIG_LEGACY_TIMEOUT_API via kconfig. These subsystems
include: CAN Bus, the Microbit display driver, I2S, LoRa modem
drivers, the UART Async API, Video hardware drivers, the console
subsystem, and the network buffer abstraction.
k_sleep() now takes a k_timeout_t argument, with a k_msleep() variant
provided that works identically to the original API.
Most of the changes here are just type/configuration management and
documentation, but there are logic changes in mempool, where a loop
that used a timeout numerically has been reworked using a new
z_timeout_end_calc() predicate. Also in queue.c, a (when POLL was
enabled) a similar loop was needlessly used to try to retry the
k_poll() call after a spurious failure. But k_poll() does not fail
spuriously, so the loop was removed.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Kernel timeouts have always been a 32 bit integer despite the
existence of generation macros, and existing code has been
inconsistent about using them. Upcoming commits are going to make the
timeout arguments opaque, so fix things up to be rigorously correct.
Changes include:
+ Adding a K_TIMEOUT_EQ() macro for code that needs to compare timeout
values for equality (e.g. with K_FOREVER or K_NO_WAIT).
+ Adding a k_msleep() synonym for k_sleep() which can continue to take
integral arguments as k_sleep() moves away to timeout arguments.
+ Pervasively using the K_MSEC(), K_SECONDS(), et. al. macros to
generate timeout arguments.
+ Removing the usage of K_NO_WAIT as the final argument to
K_THREAD_DEFINE(). This is just a count of milliseconds and we need
to use a zero.
This patch include no logic changes and should not affect generated
code at all.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Use of macros such as SYS_POWER_STATE_SLEEP_2 needs to be guarded by
making sure CONFIG_SYS_POWER_SLEEP_STATES is defined.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Convert older DT_INST_ macro use in litex drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in atmel sam0 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added device tree nodes and associated headers for
defined uarts on the stm32g0 and stm32g07x 8x parts.
Tested with uart on stm32g071rb disco board with usart3 going to stlink.
Using shell.
Signed-off-by: Kieran Levin <ktl@frame.work>
Convert older DT_INST_ macro use in STM32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in esp32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_INST_{0,1,2}_ESPRESSIF_ESP32_UART_IRQ_0 defines to something
non-DT prefixed. This way we know which defines are one's we generate
and which ones are driver created. It should be easy enough to replace
these INST_{0,1,2}_ESPRESSIF_ESP32_UART_IRQ_0 define with DTS generated
one macros once esp32 has interrupt controller support in DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in silab drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in stellaris drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a dependency on the UART resource in the TI Power module,
reconfigure the UART upon CPU exiting standby, and add support
for device PM.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The shared irq support isn't needed in this driver. We just need to
deal with the fact that some SoCs have only a single interrupt line and
some have three interrupts. We can just ifdef that based on
DT_NUM_IRQS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A txcnt of zero prevents transmission, as transmit requires the number
of entries in the transmit fifo to be strictly less than the txcnt
value. Set the default to 1.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
uart_configure verification handler was missing what would cause a crash
if called from a user thread.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
