This commit adds the `i2c-0` alias for the Atmel SAM E54 Xplained Pro
board, as required by the I2C test.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit configures the SERCOM2 peripheral to I2C mode for the Atmel
SAM D21 Xplained Pro board.
Note that the SERCOM2 on PA08/PA09 is the I2C peripheral/pin designated
by the board user guide.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit configures the SERCOM2 peripheral to I2C mode for the Atmel
SAM D20 Xplained Pro board.
Note that the SERCOM2 on PA08/PA09 is the I2C peripheral/pin designated
by the board user guide.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Remove the USART 2 definition from the nucleo_g474re board
as it could cause a pin conflict on LPUART1 TX pin (PA2).
The USART2 is not present on this nucleo hardware and then
the g474re board definition is aligned with the nucleo_g431rb.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The OpenOCD JTAG reset causes the SAM E54 SoC to prematurely start code
execution before the SoC is ready, and this causes hard faults when the
MPU is enabled -- causing OpenOCD to hang.
This commit disables the JTAG SRST reset mechanism and falls back to
using the Cortex-M SYSRESETREQ emulation reset mechanism, which does
not have experience this issue.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit enables the ARM memory protection unit for the SAM D54
Xplained Pro board, since `CPU_HAS_ARM_MPU` is now selected by the SoC
Kconfig.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit enables the QEMU icount mode for `mps2_an521`, in order to
decouple the host clock from the emulated guest clock.
This prevents guest timing instability from causing test failures when
the host CPU load is very high.
The icount `shift` value of 7 was empirically chosen to allow the tests
to complete in both realistic and reasonable amount of time.
The following are quick notes on the parameters used:
* -icount shift=7: Execute one instruction every 128ns of virtual time
* -icount align=off: Do not synchronise the host and guest clocks
* -icount sleep=off: Advance virtual time without sleeping/waiting
* -rtc clock=vm: Isolate the guest RTC time from the host
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
native_posix supports for some time now generating a 64bit
binary with the native_posix_64 target, but we never got
to document it.
Add a section describing it, and correct the WSL1
note/warning (also with a link with instructions on how to hack
WSL1 to make it run 32 bit binaries)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Options summary:
-icount shift=5: Execute one instruction every 32ns of virtual time
-icount align=off: Do not synchronise the host and guest clocks
-icount sleep=off: Advance virtual time without sleeping/waiting
-rtc clock=vm: Isolate the guest RTC time from the host
64-bit still has some issues that are being looked at.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
For autogeneration on board pages and indexes, consistency in naming is
required, few board names did not match the images of the boards.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Removing this flag allows to find the spi binary generation tool
in cmake's default paths. This also aligns this CMakeList with
the version currently found in the MEC EVB
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Add board definition for the NXP LPCXpresso55S16 development
board. Only non-secure (ns) access is supported for now.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Kukui has two I2C ports with various peripherals including a battery
charger and a TCPCi-compatible port controller
Enable I2C so that these can be used. No drivers are provided so far.
Also update the GPIO documentation while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove dts_fixup.h files that are not used (empty) or the defines aren't
used anymore and thus can be removed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert linker scripts and arc_mpu_regions.c setup to use new
devicetree.h macros to extract the base address and size of the various
memory regions (DDR, SRAM, FLASH, DCCM, ICCM). We also remove the
scaling up and down since DT_REG_SIZE() returns the value in bytes.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Do not assume in the SoC level device trees that NXP Kinetis FlexTimer
nodes will always be configured as PWM. Instead, configure FlexTimer
nodes for PWM at the board level for NXP Kinetis boards.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add ESP-8266 modules shield. The ESP-01 needs to be loaded with
ESP8266 AT Bin V1.6.2 which is compatible with ESP8266 AT Bin
V1.7.x which is the minimal supported version by ESP WIFI driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The board efr32_radio_brd4250b replaces this removed board. This
commit removes this duplication.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
The HTML documentation generation does not work properly if
we try to put more than one board into same directory. So rename
the directory to reflect this.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit enables the QEMU icount mode for `mps2_an385`, in order to
decouple the host clock from the emulated guest clock.
This prevents guest timing instability from causing test failures when
the host CPU load is very high.
The icount `shift` value of 7 was empirically chosen to allow the tests
to complete in both realistic and reasonable amount of time.
The following are quick notes on the parameters used:
* -icount shift=7: Execute one instruction every 128ns of virtual time
* -icount align=off: Do not synchronise the host and guest clocks
* -icount sleep=off: Advance virtual time without sleeping/waiting
* -rtc clock=vm: Isolate the guest RTC time from the host
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the atom/linker.ld to match how ia32/linker.ld works with regards
to how PHYS_LOAD_ADDR & PHYS_RAM_ADDR are set based on CONFIG_XIP and
from which DT_PHYS_{RAM,LOAD}_ADDR defines. We update the minnowboard
dts and atom.dtsi files to keep in sync with this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SoC node has compatibles for the specific SoC in place, having the
same compatible at the top level is technically a conflict and the
top-level one should really just be about the board. Remove the SoC
related compatibles at the top-level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert old style ifdef(DT_NS16550_400F2400_BASE_ADDRESS) to
if DT_HAS_NODE(DT_NODELABEL(uart0)) to decide to config pins for UART0
and similarly for UART1.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of CAN_X Kconfig symbols by access to dt instances
Control of enabled instances is now done using dts nodes status
field ('okay'/'disabled'). For boards supporting only can2,
can1 instance is disabled.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update STM32WB HCI lib support to version 1.5.0.
Additionally provide a doc section to clarify compatibility
with stm32wb wireless co-processor binaries.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
The pinmux_mchp_xec is also being updated since it's using DT
from GPIO.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Convert driver to use instance macro's instead of dts_fixup.h based
macros. This moves us closer to removing both dts_fixup.h and per
instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Pinmux needs to be set for UART_2 if it is enabled. So use
the new DT macro to refer to the DT node.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Pinmux needs to be set for UART_2 if it is enabled. So use
the new DT macro to refer to the DT node.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Replace DT_FLASH_DEV_NAME with DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL.
We now set zephyr,flash-controller in the chosen node of the device
tree to the flash controller device.
NOTE: For a SoCs with on die flash, this points to the controller and
not the 'soc-nv-flash' node. Typically the controller is the
parent of the 'soc-nv-flash' node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit renames the Kconfig `FLOAT` symbol to `FPU`, since this
symbol only indicates that the hardware Floating Point Unit (FPU) is
used and does not imply and/or indicate the general availability of
toolchain-level floating point support (i.e. this symbol is not
selected when building for an FPU-less platform that supports floating
point operations through the toolchain-provided software floating point
library).
Moreover, given that the symbol that indicates the availability of FPU
is named `CPU_HAS_FPU`, it only makes sense to use "FPU" in the name of
the symbol that enables the FPU.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options and dts fixups for GPIO instances.
A side-effect to using DT_INST_FOREACH is that GPIO ports A0 and A3
are now enabled, whereas they were originally disabled by default as
an optimization.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Reworked spi_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit enables the ARM memory protection unit for the SAM 4S
Xplained board, since the `CPU_HAS_ARM_MPU` is now selected by the SoC
Kconfig.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit enables the ARM memory protection unit for the SAM 4E
Xplained Pro board, since the `CPU_HAS_ARM_MPU` is now selected by the
SoC Kconfig.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Sort the supported lists alphabetically for some boards. I'm not
trying to do this for all boards, just some DKs I'm using for testing.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Tests were failing as they were looking for an alias which didn't exist
Also, because some code in kscan_handlers.c wasn't compilable
Signed-off-by: Mark Olsson <mark@markolsson.se>
Changes dependency for I2C so that it's enabled if kscan is enabled.
This is to allow the kscan_ft5336 sample to run.
Note: LVGL has KSCAN as a dependency.
Applies to the mimxrt10{50,60,64}_evk boards.
Signed-off-by: Mark Olsson <mark@markolsson.se>
Adds device tree nodes, pinmux definitions and configures Kconfig
defaults for the ft5336 touch panel driver on the
stm32f746g_disco board.
Signed-off-by: Mark Olsson <mark@markolsson.se>
Adding port information for uart tx and rx pins in dts, so that it can
be more systematically retrieved in the uart driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Convert driver to use DT_INST_ defines. As part of this conversion we
remove the Kconfig options for per GPIO controller enables and instead
get that information from device tree. This means we now disable each
GPIO controller by default in the DTS and have each board dts enable the
GPIO controller ports it needs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the asynchronous UART API testing support on the SAM
R21 Xplained Pro board.
The SERCOM3 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM3 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Replace DT_ALIAS_GPIO_x_LABEL with DT_NODELABEL references to get the
device name for the gpio ports.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adding support for nRF9160 based InnBlue board V2.1. Supports both
Secure and Non-Secure configurations along with various sensors
(lis2dh12 / hts221) and devices(i2c / pwm).
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Move the FPGA GPIO init to use the devicetree.h macros instead of
dts_fixup.h. This allows us to remove dts_fixup.h on mps2 based
platforms.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
SPI1, which is used by the LoRa radio, has the following
configuration:
SCK: PB_3
MISO: PA_6
MOSI: PA_7
NSS: PA_15
Update the pinmux configuration and documentation to reflect this.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
Convert old DT defines of the form DT_ARM_SCC_BASE_ADDRESS to
DT_REG_ADDR(DT_INST(0, arm_scc)). This allows us to remove dts_fixup.h
on musca boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In conversion of nodelabels to match SoC docs, we missed a case in the
board dts files. However these delete-node commands are not needed as
we normally handle this via the 'status' property being disabled which
enet2 is by default in the SoC dtsi files. So we can safely just remove
the stale /delete-node/ eth1 lines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adding support for nRF9160 based InnBlue board V2.2. Supports both
Secure and Non-Secure configurations along with various sensors
(lis2dh12 / hts221) and devices(i2c / pwm).
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
Set the default value of SYS_PM_MIN_RESIDENCY_SLEEP_1 and
SYS_PM_MIN_RESIDENCY_SLEEP_2 to something more reasonable for these
platforms, as the latency of entering/exiting these sleep modes
is low.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The nvs sample requires a storage_partition of 3 flash pages, but these
boards only provided 2 flash pages. Because of this the nvs sample
failed.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Add script signing and flashing up_squared_adsp board. Can be used:
$ west flash \
<zephyr>/boards/xtensa/up_squared_adsp/tools/up_squared_adsp_flash.sh
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Reworked i2c_sam_twi driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked i2c_sam_twi driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Given that nsim_em can run the tests instead of just building them as
with em_starterkit_em7d, make it a default platform instead of
em_starterkit_em7d to get most of the testing when nsim simulator is
installed on the developer machine.
Tests run are 1000x more useful than just building them, even if we do
not have a large installed base of nsim.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Update documentation about IC variations. Now SoC supports both
variations A and B and this board is compatible with both.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Update documentation about IC variations. Now SoC supports both
variations A and B and this board is compatible with both.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of Kconfig UART_X symbols by calls to DT API.
Clean driver from symbols definitions
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage. We also remove dts_fixup.h defines that
are no longer needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Mark all the individual PWMs as disabled in dts and enable the one
explicitly used on the mimxrt1064_evk.dts in the board dts file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change the board defconfig to use the provided 24MHz Crystal instead
of the internal resonator.
This improves the clock precision and stability.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Change the board defconfig to use the provided 24MHz Crystal instead
of the internal resonator.
This improves the clock precision and stability.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Now the ARC SecureShield related features are experimental. The ARC
normal application cannot run alone, need the secure service example to
initialize the context and boot.
Here move ARC normal related configurations out of board dir to
avoid the impact of CI test and the confusion to users.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Reworked usart_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked uart_sam driver to utilize new DT_INST macros as part of this
rework we also now get pin ctrl/mux configuration information from the
device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The return value of the interrupt is never used, so remove the
functionality from the API. We ripple this change into the
ARCH_IRQ_CONNECT and ARCH_IRQ_DIRECT_CONNECT implementations. With
this change we can also remove the compound expression as that is
not needed anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We don't need to define DT_NUM_IRQ_PRIO_BITS or DT_NUM_MPU_REGIONS in
dts_fixup.h files anymore, so we can remove them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The documentation references now out-dated links to websites for
board landing page, and firmware download and instructions. This
commit updates the links and adds a link to the latest firmware
development for reference.
Fixes#24325
Signed-off-by: Jennifer Williams <jennifer.m.williams@intel.com>
This commit enables the GMAC Ethernet support for the `atsame54_xpro`
board which includes an on-board RMII PHY.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
In order to use its serial peripheral SERCOMs SAMD socs require their
pins to be configured with pinmux. Currently pins are muxed only for the
boards' default serial interfaces. The pinmux code is written to throw
a compiler error if a user tries to use any sercom in a way it wasn't
pre-defined to be used.
This commit changes compiler errors to warnings so that user can provide
custom pinmuxing code in their app.
Fixes#23133
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
This commit enables the newly added GMAC instance in the `sam4e_xpro`
device tree.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This enable GMAC driver by default if the end application selects
NETWORKING. The driver will set MII interface since is the only one
available for SAM4E and will select a random MAC value.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This patch adds the selection of the necessary CONFIG_*
options for allowing the use of privacy on VEGA platform
Signed-off-by: Jeanina Dragusin <ancajeanina.dragusin@nxp.com>
The radio on the VEGA platform will now be able to resolve Resolvable
Private Addresses through the use of the CAUv3 hardware. With this
patch the RPA feature is now fully supported on the Controller:
RPA addresses are generated with local IRK and resolved with
previously exchanged peer IRK.
Signed-off-by: Jeanina Dragusin <ancajeanina.dragusin@nxp.com>
This board contains an on-board Winbond W25Q16.
The chip is connected to spi1 using PB3-PB5 and PB0 as CS.
Signed-off-by: Bjarne Steinsbo <bjarne@gmail.com>
While the Cortex-R arch port does not currently support memory
protection and userspace, the `memory_protection` and `userspace` test
tags should not be ignored because doing so can unintentionally disable
other relevant tests.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Following conversion of stm32 i2c driver to use of DT_NODELABEL
macros, configuration of i2c instance in stm32 boards should
no more be done thanks to Kconfig symbols, but is done thanks
to device tree file.
Clean boards files from these symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This adds the support of openocd for nucleo board stm32g474re
It requires the openocd that supports stm32G4xx
(zephyrproject-rtos/openocd#24)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds the support of openocd for nucleo board stm32g431rb
It Requires the openocd that supports stm32G4xx
(zephyrproject-rtos/openocd#24)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds the support of openocd for nucleo board stm32g071rb
It requires the openocd that supports stm32G0xx
(zephyrproject-rtos/openocd#24)
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Towards moving uart mcux driver to DT_INST based, we need to convert
uses of CONFIG_UART_MCUX_[0-9] to use DT_NODELABEL instead. This way
the pinmux settings are still based on specific instances of the uart.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit fixes the incorrect memory (FLASH and SRAM) size
specification in the device tree and the board test yaml files.
The `qemu_cortex_r5` board (using `fdt-single_arch-zcu102-arm.dtb` FDT)
has 64MiB RAM at the address 0 and 32MiB QSPI flash at 0xc0000000.
QEMU `info mtree`:
0000000000000000-ffffffffffffffff (prio 0, i/o): memory@00000000
0000000000000000-000000000002ffff (prio 0, ram): ddr_bank1_1@0x0
0000000000030000-000000000003ffff (prio 0, ram): ddr_bank1_2@0x30000
0000000000040000-0000000003ffffff (prio 0, ram): ddr_bank1_3@0x40000
00000000c0000000-00000000c1ffffff (prio 0, i/o): lqspi
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Use the new devicetree API. Remove per-board enabling of ADC_0 by
setting ADC_0 to default y when the 'adc' node label points at an
enabled node of the expected compatible (depending on SoC).
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Those are used only in tests, so remove them from kernel Kconfig and set
them in the tests that use them directly.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Per instance Kconfig symbols aren't used by the rv32m1 lpspi driver
so remove the unnecessary setting of PWM_2.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Updated the openisa,rv32m1_vega-pinmux binding to require the label
property and updated the rv32m1.dtsi to add label properties for the
pinmux nodes.
Also update gpio_basic_api test to use DT_NODELABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move soc.c code to utilize DT_NODELABEL
instead.
Also rename various node labels to match the SoC docs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as spi. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as usart. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as i2c. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This change ensures that shared memory doesn't hold any pre-reset
values after Soft reset is issued. When the Network Core boots up,
shared memory is always set to zero.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Convert stm32 entropy driver to configuration based on device tree.
Select HAS_DTS_ENTROPY symbols and configure CONFIG_ENTROPY_NAME
in fixup files.
Since rng node is not enabled (or available) on all boards, it could
happen that symbol ENTROPY_STM32_RNG is not enabled and hence
ENTROPY_HAS_DRIVER not selected which ends up with a symbol
ENTROPY_NAME defined throufg Kconfig selection. Thus, in fixup file,
CONFIG_ENTROPY_NAME is defined only if not already defined.
Additionally, update boards that used to configure entropy by default.
On these boards, enable rng device in device tree and remove Kconfig
related configuration (which should not be part of default
configuration).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Instead of using Kconfig options for setting the device name and IRQ
priority for the entropy_nrf5 driver, get these settings from the rng
node defined in DTS for a given SoC.
Provide also fixups for CONFIG_ENTROPY_NAME, until applications using
entropy drivers are converted to use DTS as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Correct the documentation page title for the
nRF9160 DK, to match the official Dev-Kit name.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add a deprecation warning for nrf5340 PDK when the old name,
nrf5340_dk_nrf5340, is used instead of the new board name.
For nRF5340 SoC: do this for both secure and non-secure board
targets, and for both Application and Network MCU.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We rename the nRF53 Dev Kit board target (nrf5340_dk_nrf5340)
to nrf5340pdk_nrf5340. We update all associated references
in the supportive documentation and all nRF5340-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The board name for the Thingy:52, so far known as nrf52_pca20020, is
renamed to thingy52_nrf52832. Its documentation and all references to
its name in the tree are updated accordingly. Overlay and configuration
files specific to this board are also renamed, to match the new board
name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52840 Dongle, so far known as
nrf52840_pca10059, is renamed to nrf52840dongle_nrf52840. Its
documentation and all references to its name in the tree are updated
accordingly. Overlay and configuration files specific to this board are
also renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52833 DK, so far known as nrf52833_pca10100,
is renamed to nrf52833dk_nrf52833. Its documentation and all
references to its name in the tree are updated accordingly.
Overlay and configuration files specific to this board are also
renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board target for emulation of nRF52810 on nRF5DK, so far
known as nrf52810_pca10040, is renamed to nrf52dk_nrf52810.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF51 Dongle, so far known as nrf51_pca10031, is
renamed to nrf51dongle_nrf51422. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to match
the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add a reference to the PCA number to help users identify the board and
for consistency with the rest of the boards.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Also update counter_basic_api test to use DT_INST and remove the
udoo_neo_full_m4.conf as its not longer needed since the per instance
Kconfig sybmols don't exist anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Additionally remove udoo_neo_full_m4.conf from gpio_basic_api test since
the Kconfig symbols don't need to be set anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As prep for drivers being converted to utilize DT_INST and removal of
per instance Kconfig symbols, move board pinmux.c code to utilize
DT_NODELABEL instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all posix boards have a dts we can move the selection of
HAS_DTS to the arch level like it is for all the other architectures.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables PWM support using the built-in red LED. Tested with:
- samples/basic/blink_led
- samples/basic/fade_led
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Kconfig options that enable I2C and SPI instances are no longer used
in nRF drivers. Remove all assignments done to these options in related
board definitions, samples, and tests.
For nrf52_pca20020, also no longer needed setting of default values
for GPIO_SX1509B* options is removed (now the gpio_sx1509b driver is
enabled by default when a corresponding devicetree node is enabled).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `UART_x_NRF_UART*` that select
the type of nrfx driver (for UART or UARTE peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding UART node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between UART and UARTE for a given instance.
Since all `UART_x_NRF_UART*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `I2C_x_NRF_TWI*` that select
the type of nrfx driver (for TWI or TWIM peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding I2C node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between TWI and TWIM for a given instance.
Since all `I2C_x_NRF_TWI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `SPI_x_NRF_SPI*` that select the
type of nrfx driver (for SPI, SPIM, or SPIS peripheral) to be used
for a given instance. This prevents the options from being modified
in configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding SPI node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between SPI, SPIM, and SPIS for a given instance.
Since all `SPI_x_NRF_SPI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
