b6d45423c6 Added support for pin retention but it was added
only to the case when device PM is used. There is another mode
in which UARTE is disabled when idle (low power mode) and in
that case pin retention must also be added.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
If a character is received immediately after modem_iface_uart_init called,
the modem_iface_uart_isr function will not read the data in the serial port
fifo register as the context has not been registered at this time,
which will result in the program not being able to exit the interrupt,
so the context should registered before the serial port is initialised.
Signed-off-by: Hongquan Li <hongquan.prog@gmail.com>
Replace NULL checks for the set and clear registers with BUILD_ASSERTs
in the iCE40 device instantiation.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
The API directory really isn't the best place for shell
documentation, which isn't API.
Created a new directory for Bluetooth shell documentation
and moved the ISO and LE Audio docs in there.
The existing bluetooth-shell.rst file was also split into
several new files, so that it follows the same structure.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Change in default flash map generation, where partitions hanging of
disabled devices will not have flash area generated.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Add an option for platforms or forks to provide their own hostap
compatible crypto implementation. This may include proprietary or
platform specific stuff that may or may not be upstreamed to Zephyr.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Extended hardware map to share a single board between variants.
To run tests for different variants on the same board
without re-configuring the hardware map file for each variant,
one can use a `platform` atribute as a list of names.
Signed-off-by: Grzegorz Chwierut <grzegorz.chwierut@nordicsemi.no>
This commit changes the BSIM tests to use the same recv callback
for all tests. The purpose of this is to reduce code duplication
and make it easier to maintain the tests.
This also changes the recv_cb so that in case of any error we log
the most recently received SDU, which should provide more
information about why a test failed in case of RX error.
PBP had to be updated a bit to support the audio_stream
struct.
Also modifies a check and log in bap_stream that was less than
helpful to determine if it was the stream or the endpoint that
was NULL.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Non-confirmable CoAP requests need lifetime tracking as well
so we can free the structure after a timeout.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
When waiting for response after receiving the empty Ack, client
actually used way too timeout.
CoAP timeout only holds the timeout value in ms. t0 is the starting time.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Refactor tests to be a bit shorter, so its easier to read
and copy-paste for a new testcase
All idioms like "ret = somecall(); zasser.." are replaced with just
"zassert_ok(some_call());"
Commonly used structures are global and initialized once.
To avoid cross-test side-effects, suite_after-function is added
to cleanup all requests.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Use real-time scheduler with 100x speedup, so timeouts are
accurate enough, but still fast for tests to run.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Updates and aligns the project config file to enable usage of multiple
keys so that users are not required to manually update the project
config file for testing most common mesh scenarios requiring multiple
netkeys and appkeys.
Signed-off-by: Omkar Kulkarni <omkar.kulkarni@nordicsemi.no>
Aligns subnet bridge related commands according to conventions used for
rest of the shell commands. Also updates documentations to reflect the
change.
Signed-off-by: Omkar Kulkarni <omkar.kulkarni@nordicsemi.no>
We hit some unaligned access faults running our internal tests.
Not every 32-bit instruction is 32-bit aligned; some are 16-bit aligned.
Make all reads and writes potentially unaligned to be on the safe side.
Signed-off-by: Ilya Tagunov <Ilya.Tagunov@synopsys.com>
Not all STM32 series support Zephyr MDIO API yet, while the API is enabled
by default.
To preserve compatibility, put MDIO API related code under the condition
of "st,stm32-mdio" compatible enablement.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Documentation for *init_hooks were not generated on doc website.
This was due to ill-formed doc-strings for those hooks.
Signed-off-by: Pierrick Guillaume <pierguill@gmail.com>
Previously, rtt start would always fail because the target
(i.e. firmware) had not been started.
```
Info : rtt: Searching for control block 'SEGGER RTT'
Info : rtt: No control block found
```
When the command is 'rtt', run the binary via gdb before calling
'rtt start'. Firmware calls `SEGGER_RTT_Init()` shortly after
init which allows OpenOCD to find the RTT control block.
Similarly, only start the 'rtt server' after calling
'rtt start' to avoid any potential race conditions
internally within OpenOCD.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Previously, there was a warning that the to_num() method can
(and probably should) be unbound from OpenOcdBinaryRunner.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Similar to how print_gdbserver_message() prints GDB server info
when "west debug" is run, print RTT server info when "west rtt"
is run.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
Add support for the rtt target so that users can run
`west build -p auto -b <board> -t rtt <app>`
similarly to the way that users can now do so with the debug
target, since the rtt target is supposed to be used in a similar
way.
Signed-off-by: Chris Friedt <cfriedt@tenstorrent.com>
The nRF54L05 and nRF54L10 are identical to the nRF54L15 except for their
memory sizes. Add support for emulating those ICs on the nRF54L15DK.
This commit only adds support for the main application core. Support for
the FLPR core may be added later.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the rather logical convention for the name that is applied to other
Nordic boards: <board>_common.dtsi for definitions that are common to
the board itself (LEDs, buttons, etc).
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
These two new ICs are variants of the nRF54L15 with different memory
sizes:
- nRF54L05: 500KB RRAM, 96KB RAM
- nRF54L10: 1022KB RRAM, 192KB RAM
- nRF54L15: 1524KB RRAM, 256KB RAM
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
There are many common options to all ICs of the 54L series. Consolidate
them in a single entry so that they do not need to be re-typed for each
SoC series member.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
TASK_SHUTDOWN was deprecated in newer SOCs and now removed
in MDK 8.68 (nrfx 3.9.0)
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Update the HW models module to:
3cfca0192ff84da919e9bc7978bcc2239cd6a395
This includes 2 changes:
* 3cfca01 UART: Model more accurately TASKS_FLUSH behaviour
* 25cbd28: 54L15: Change CLOKPOWER IRQ line (MDK 8.68, nrfx 3.9.0)
WARNING! This change breaks backwards compatibility with SW
which expected this line to be 270 for 54L15 devices,
and therefore with MDKs < 8.68 & nrfx < 3.9.0.
This change requires updating to the MDK >=8.68 and nrfx >=3.9.0
if building using the 54L15 models.
52 and 53 models are not affected.
Change the CLOCK_POWER interrupt line from 270 to 261.
This has changed in the latest MDK (8.68) and the new
value is used in the latest nrfx (3.9.0) drivers.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Update the HW models module to:
42737c8ec8485987c7c9b0262b136de623e1ded2
Including the following:
42737c8 TIMER: Support devices without TASK_SHUTDOWN nrfx3.9 MDK 8.68
5fe6873 54 UARTE: Add frametimeout functionality
dc086d7 UARTE: Add basic 54 support
b046745 UARTE: Support better not having UART functionality
1c5f58c README: Mention the nRF54L15 models cover the L10 and L05
597c7d0 TEMP: Also build hal replacement for 54 and define NRF_TEMP_NS/S
fb2ca83 Makefile: Let's build libraries (specially HAL) as pic
200a1e3 Makefiles: move some common options to common snippet
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Adds two new tests for the Subnet Bridge feature, testing group and
virtual addresses as destinations. The tests are based on the existing
`brg_simple.sh` test, with the addition of a new node and a new subnet
to make sure that messages are bridged to multiple subnets, but only
subnets that have a corresponding entry in the bridging table.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Renames `bt_mesh_test_send_ra` to `bt_mesh_test_send_data` and changes
the corresponding callback funciton as it is used outside of the replay
attack tests, and can be used to send custom data. The function is
extended to accept a UUID parameter to allow sending data to virtual
addresses.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
device tree:
enable support for the SDHC controller to use the micro SD card slot
documentation:
- added instructions for SD card and OLED samples
- added links to code samples
defconfig:
added CONFIG_ESP32_USE_UNSUPPORTED_REVISION=y to
ttgo_lora32_esp32_procpu_defconfig
The chip on the board is a ESP32 chip revision 1.
The board will not boot, it displays the following warning at boot:
I (35) boot: chip revision: v1.0
E (38) boot: You are using ESP32 chip revision (1) that is unsupported.
While it may work, it could cause unexpected behavior or issues.
E (50) boot: Proceeding with this ESP32 chip revision is not recommended
unless you fully understand the potential risk and limitations.
E (62) boot: If you choose to continue, please enable the
'CONFIG_ESP32_USE_UNSUPPORTED_REVISION' in your project configuration.
E (73) boot: HW init failed, aborting
In order to prevent a boot loop, CONFIG_ESP32_USE_UNSUPPORTED_REVISION=y
was added to the defconfig.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Use the existing 'atomic' bitmask to speed up ISR processing for
CONFIG_DMA_INTEL_ADSP_HDA_TIMING_L1_EXIT. This bitmask is used
to track enabled DMA channels.
In the common case, only a few DMA channels are active and low
channels are allocated first. Take advantage of this and not
iterate over all DMA channels of all all host devices. Rather
break out as soon as L1 exit handling is done for all enabled
channels.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Change the select to a depends on for the Kconfig options
for HAS and HAS_CLIENT.
This is an effort to reduce the number of selects used by
LE Audio.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Change the select of BT_PER_ADV_SYNC and BT_EXT_ADV to
depends on. This is an effort to reduce the use of
select for Kconfig options.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Modify ASCS and BAP Broadcast sink to depend on the PAC options
instead of selecting them.
Since Kconfig does not support "depends on X if Y",
a select for PAC_{SRC,SNK} is used depending on
ASCS_ASE_{SRC,SNK}.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
