This reverts commit c9ace83c89 which
bypasses setting cache attributes.
The previous cache attributes actually set the text/data/etc.
sections to be inaccessible. So fix it.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
All text, data and bss sections are all mapped to the same physical
memory (SRAM). This patch removes the individual section limits
and defines a common limit for the sum of text, data and bss sections.
This would make it more flexible for application developers.
Fixes#11268.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
CONFIG_TEXT_SECTION_OFFSET allows the entire image to be moved
in memory to allow space for some type of header. The mcubootloader
can boot only such images which reserve some space for the header.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
We now place the linker directives for the SW ISR table
in the common linker scripts, instead of repeating it
everywhere.
The table will be placed in RAM if dynamic interrupts are
enabled.
A dedicated section is used, as this data must not move
in between build phases.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add a linker script entry for embedding a GNA model at a
4KB page aligned address in .data section
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
This adds the necessary bits to support ASM2 with XCC
for Intel S1000 SoC. With ASM2 enabled, xcc is now
required to build for Intel S1000 SoC.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
(Previous patch set was reverted due to issue with priv_stack.
Resubmitting after fixing the faults caused by priv_stack.noinit
not at the end of RAM.)
This adds a linker flag and necessary changes to linker scripts
so that linker will warn about orphan sections.
Relates to #5534.
Fixes#10473, #10474, #10515.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds a linker flag and necessary changes to linker scripts
so that linker will warn about orphan sections.
Relates to #5534.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Move the SoC outside of the architecture tree and put them at the same
level as boards and architectures allowing both SoCs and boards to be
maintained outside the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
2018-09-13 00:56:48 -04:00
Renamed from arch/xtensa/soc/intel_s1000/linker.ld (Browse further)
