This supports nuvoton numaker m55m1x series soc. Besides, it also
has relevant modifications, including:
1. Fix failure to enable HICR48M, which is to clock usbd and phy
2. Support HWINFO for USB device serial number
Signed-off-by: Chun-Chieh Li <ccli8@nuvoton.com>
Allow for users to define the fifo-watermark on a per-instance basis
through device-tree properties. This setting is validated at build
time, so missing it when required, or setting an invalid value should
not end up in a run-time errror (as in: it runs but nothing happens).
Signed-off-by: Luis Ubieda <luisf@croxel.com>
This patch fixes previous overriding of ODR setting through DTS (it
would always be 25-Hz, irrespective of what the DTS property said).
While doing so, create dt-binding enum to improve settings clarity.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
The new ace30 files structure is organized as follows:
intel_adsp_ace30.dtsi - main file for all variants
intel_adsp_ace30_ptl.dtsi - additional file for PTL variant
intel_adsp_ace30_wcl.dtsi - additional file for WCL variant
The main ace30.dtsi file contains most of the fields,
with only the differences specified in the ace30_ptl.dtsi
and ace30_wcl.dtsi files.
Signed-off-by: Adrian Bonislawski <adrian.bonislawski@intel.com>
The first 1 KB is reserved for the NWP (Network Coprocessor). This
change also resolves the null pointer error issue, as a .data or a
_ramfunc might get the address 0x0.
Signed-off-by: Martin Hoff <martin.hoff@silabs.com>
Removed the duplicate 'ovti' entry and updated the full name to
company's current official name.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Thanks to the bootloader, the memory controller is preconfigured when
Zephyr start on RB44342A.
However, this is the opportunity to show how to configure the PSRAM
controller on custom designs.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Silabs siwx91x includes a memory controller for (Quad-)SPI PSRAM. It
allows the application to use the PSRAM as if it was any other RAM.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Add a reusable uart-bridge driver that echoes data between two serial
devices. It's mainly meant to be used with one of the devices being an
USB CDC-ACM, the data is buffered, there's a pause feature to stop the
USB endpoint when the hardware UART is filling up to avoid overrun and
there's a helper function used to propagate the USB uart configuration
to the hardware one.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
ElemRV-N is based on the nitrogen SoC platform. Add the
base nitrogen device-tree and one for elemrv-n. The elemrv-n
device-tree will contain all IP cores later.
Signed-off-by: Daniel Schultz <dnltz@aesc-silicon.de>
Add minimal support for the aesc silicon UART IP core.
This core includes an internal clock divider and supports flexible
frame configurations, allowing for variable data length, parity, and
stop bit settings.
The current driver version does not support interrupts.
Signed-off-by: Daniel Schultz <dnltz@aesc-silicon.de>
aesc silicon is a startup focused on developing open-source
silicon solutions.
Link: https://github.com/aesc-silicon/ElemRV
Signed-off-by: Daniel Schultz <dnltz@aesc-silicon.de>
Rename the frac-v PLL binding into fracn in order to make it
consistent with other STM32 PLL bindings.
This commit also correct the range which should be 0 - 8191.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Depending on the PLL, all DIV-P / DIV-Q and DIV-R are available
on STM32MP13 PLLs.
Adjust valid range in order to be able to set for all 4 PLLs.
Clarify DT properties description.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
This commit adds following updates to MAX32650 SoC:
- Divide SRAM to sections according to UG.
- Add DMA and SPI nodes
- Add WDT nodes without adding clock property
- Include dma binding to SoC dts file.
Signed-off-by: Furkan Akkiz <hasanfurkan.akkiz@analog.com>
Signed-off-by: Burak Babaoglu <burak.babaoglu@analog.com>
This commit changes clock property of watchdog to optional and updates
driver according to this change.
Signed-off-by: Furkan Akkiz <hasanfurkan.akkiz@analog.com>
Add an led_strip driver for the modulino smartleds module. This is a
pluggable I2C board with 8 addressable RGB LEDs
The I2C protocol is implemented on an microcontroller on the modulino
board itself, the firmware for that is open source and can be updated
using an Arduino sketch:
Link: https://github.com/arduino/node_modulino_firmware
Link: https://github.com/arduino-libraries/Modulino
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add an input driver for the modulino buttons module. This is a pluggable
I2C board implementing three buttons and three LEDs, the I2C protocol is
implemented on a microcontroller on the modulino board itself, the
firmware for that is open source and can be updated using an Arduino
sketch:
Link: https://github.com/arduino/node_modulino_firmware
Link: https://github.com/arduino-libraries/Modulino
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Implement the video API frame interval handling in order
to control the framerate of capture.
This allow to remove the capture-rate DT property as well.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
With the addition of the dma property within the soc dtsi, it is
no more necessary to add it within the board dts.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Usage of dma is mandatory for the dcmi and this property is
tightly coupled with the soc itself since the configuration of
the dma depends on the source/destination, and the request line
is also fixed for an ip.
Instead of having to always have the dma property part of the
board or shield dts/overlay, add the dma property into the
dcmi node of the stm32h7.dtsi.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Update the bindings of the stm32-dcmi driver rely on
properties described within the endpoints and already
detailed within the video-interfaces.yaml.
With that, several properties located at the node root
are now moved into the port / endpoint:
sensor -> endpoint: remote-endpoint-label
vsync-active -> endpoint: vsync-active
hsync-active -> endpoint: hsync-active
pixelclk-active -> endpoint: pclk-sample
bus-width -> endpoint: bus-width
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
