stm32mp1 was adding a STM32 specific Core selection Kconfig
symbol while zephyr generic CPU_CORTEX_M4 could be used for the
same purpose.
Remove STM32 specific symbol and use generic one.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Sample was not compiling for nordic boards because RTC_0
instance was not enabled by default and RTC_0 device is using
different DT define.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add dts fixup definitions for low power sram base address and size
- DT_LP_SRAM_BASE
- DT_LP_SRAM_SIZE
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
This commit adds counter driver based on RTCC module for SiLabs Gecko
SoCs.
Tested with SLWSTK6061A / BRD4250B wireless starter kit.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add board support (and documentation) for the Intel Gordon Peak
Module Reference Board, a dev board based on the Apollo Lake SoC.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
These events aren't errors at all, but rather part of normal operation.
They shouldn't trigger error messages, especially given that the console
gets absolutely flooded with them if power management is activated.
Signed-off-by: Benjamin Lindqvist <benjamin.lindqvist@endian.se>
1. Add flash partitions.
2. Add macro DT_START_UP_ENTRY_OFFSET. The entry of the RV32M1 is
not the start of the vector table. Add the macro to inform the
entry offset.
3. Update linker file to support MCUboot
a. For normal cases (CONFIG_BOOTLOADER_MCUBOOT is cleared), the
vector table is located last 256bytes of the flash.
b. If CONFIG_BOOTLOADER_MCUBOOT is set, the vector table is located
after the image header of MCUboot.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
stm32wb55rg is a dual core SoC (M4/M0) with a radio/protocol stack
running on M0 core. M0 FW starts at flash address 0x80CB000.
So flash size available to zephyr is 812K instead of 1M.
Configure package size to reflect this (flash size is now 812K)
and update MPU setting to exclude M0 FW. From MPU point of view,
we set flash size to 512K since we should chose a size being a power
of 2.
If we consider there will be 2 images partitions in a FOTA scheme,
512 K is beyond image-0 and hence is sufficient to cover application
image.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32WB HCI driver requires definition of 2 RAM regions to support
use of 3 shared memory sections: MAPPING_TABLE, MB_MEM1 and MB_MEM2.
In linker.ld, under conditions of HCI driver to be enabled,
define SRAM1 and SRAM2 based on input defined in stm32wb linker.
Then define the 3 sections MAPPING_TABLE, MB_MEM1 and MB_MEM
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The Apollo Lake SoC no longer uses the legacy PCI driver, so remove
references and supporting code.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
While enabling specific I2C ports does indeed belong at the board
level Kconfig, the selection of driver (I2C_DW) is an SoC-level
choice, so it is moved accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Which UARTs are broken out from the SoC on a particular board is
board-specific; don't enable UARTs blindly in the SoC Kconfig.
Also, the default UART options are specified in the driver Kconfig, so
the same defaults specified in the SoC Kconfig are redundant. Removed.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The UART references in dts_fixup.h are actually SoC-specific, not
board-specific, so they are moved. Since this leaves the board fixups
empty, the file is removed.
The SoC fixups are expanded to include the additional two ports that
are present on some revisions of the Apollo Lake.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Several customer configuration (CCFG) settings are useful for
development and deployment. This commit adds support for setting CCFG
values via Kconfig. It follows TI's recommendation of setting CCFG
values and then including the TI provided CCFG. This commit includes
support for enabling the ROM bootloader and additional settings can be
added as needed.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
The HiFive1 and HiFive1 Rev B share the same clock initialization
code, so put it in soc/riscv32/riscv-privilege/sifive-freedom.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
The HiFive1 Rev B adds the following features to the
original HiFive1:
- A second UART peripheral 'uart_1'
- A hardware I2C peripheral 'i2c_0'
- Segger J-Link OB
- An ESP32-WROOM attached to the 'spi_1' peripheral bus
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
soc_register.h is available in most of stm32 series.
It is sometime empty or contains includes to flash_registers.h,
which is included directly with direct reference in flash driver.
soc_register.h is also included in stm32 clock drivers, but this
driver do not use direct reference to any register anymore.
Clean up these files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
tests/drivers/i2c/i2c_api wants to have CONFIG_I2C_0_NAME defined.
Add it to dts_fixup.h as was done for Watchdog and & timer.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This adds support for the basic timer counter (TC) found on SAM0
series parts. This driver only supports running the counter
in 32 bit wide mode. Since this mode explicitly slaves the odd
counters to the even ones, only instances of the even ones are
defined.
Tested with tests/drivers/counter/counter_basic_api on SAMD21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Define pinmux base addresses from gpio bases. Pinmux
and gpio functionality are located in the same PCR register
for each pin.
Introduce pinmux Kconfig switches for the SOC.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
This commit enforces platform-specific initialization
for nRF SoC family. The specific platform initialization
hook is invoked directly after reset and calls the nRFx
SystemInit() function.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
If the QMSI is not configured in (in the west manifest) we get kconfig
whitelisting errors because the type is declared within the module
itself.
Change default to def_bool to set the type.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add support for the Low Power Inter-Integrated Circuit (LPI2C)
controllers found in the NXP Kinetis KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add option for enabling the Code Cache present on the NXP Kinetis
KE1xF SoC series and enable it by default.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
