Instead of enabling Bluetooth by default on nRF5x boards, only enable
the controller if Bluetooth has been enabled by the applicaiton.
Fixes#5454Fixes#12215
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Few boards supporting RTC were missing rtc as supported rtc feature
in yaml files. Fix this.
Add counter to all boards supporting rtc as RTC IP now support
both rtc and counter API.
Change split in 3 parts in order to lower CI load and get shippable
happy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Few boards supporting RTC were missing rtc as supported rtc feature
in yaml files. Fix this.
Add counter to all boards supporting rtc as RTC IP now support
both rtc and counter API.
Change split in 3 parts in order to lower CI load and get shippable
happy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Few boards supporting RTC were missing rtc as supported rtc feature
in yaml files. Fix this.
Add counter to all boards supporting rtc as RTC IP now support
both rtc and counter API.
Change split in 3 parts in order to lower CI load and get shippable
happy.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Configure RTC on nucleo_f746zg.
It is supported through counter RTC API.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Enable testing of counter (COUNTER_{D}TMR_CMSDK) on mps2_an385 and
enable timers on v2m_beetle (TIMER_{D}TMR_CMSDK).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CMSDK Dual Timer can be used as a timer or as a counter.
The unified interface proposed in #8340 unifies counter.h and rtc.h to
provide a common interface.
This patch modifies the timer implementation of the dual timer to
make it compliant with the new proposed interface.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CMSDK Timer can be used as a timer or as a counter.
The unified interface proposed in #8340 unifies counter.h and rtc.h to
provide a common interface.
This patch modifies the timer implementation of the single timer to
make it compliant with the new proposed interface.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enabled EPIT (Enhanced Periodic Interrupt Timer) in Cortex-M4 core
of Udoo Neo Full board so the counter API could be used there.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Add driver support for kinetis ID device.
The length depends on the SoC.
`SIM_GetUniqueId` was not used because the struct would reorder
the ID and makes the driver more complicated because the length
of the struct depends on the SoC.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Adds device tree bindings and nodes for the rocktech lcd module used on
imx rt boards. The use of port, endpoint, and remote-endpoint properties
follow what is currently done in linux, but they are not yet used in
zephyr because some additional plumbing is needed in the
extract_dts_includes.py script.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Always link firmware built for nrf9160_pca10090ns into the
code-partition defined in DT, regardless.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Introduce BOARD_NRF9160_PCA10090NS to differentiate between
secure and non-secure board variants.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
When selecting BT we need to select BT_CTRL for most bluetooth
samples to work correctly.
Let's fix that in the board files.
Fixes the following error when CONFIG_BT is selected:
zephyr/drivers/bluetooth/hci/h4.c:463:30:
error: ‘CONFIG_BT_UART_ON_DEV_NAME’ undeclared (first use in
this function)
h4_dev = device_get_binding(CONFIG_BT_UART_ON_DEV_NAME);
^~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Michael Scott <mike@foundries.io>
Enable the SPI driver on the HiFive 1
This makes the following configurations choices for the HiFive 1:
The SPI 0 peripheral driver is not enabled by default because it is in
charge of mapping the SPI flash into memory. This can be configured
using the CONFIG_SIFIVE_SPI_0_ROM KConfig option.
The SPI 1 peripheral driver is enabled by default and the pinmux is
configured for all of its outputs
The SPI 2 peripheral driver is enabled by default because it is present
in the DTS for the FE310, but because the QFN48 package used on the
HiFive 1 doesn't route those pins from the silicon die, the pinmux can't
enable the SPI 2 pins.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Indicate that PWM is supported on several Nordic DK boards so that
the pwm_nrf5_sw and pwm_nrfx drivers are covered by CI builds.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Enable HW PWM driver instead of the SW one on nRF SoCs where the PWM
peripheral is present.
Default PWM instances are also enabled on Nordic DK boards so that it
is possible to build the basic fade_led sample for them without extra
adjustments.
After the above changes are applied, some configuration alterations
in basic samples blink_led and fade_led become no longer needed.
These are removed. And the blink_led sample is corrected so that it
works with the nRF HW PWM driver as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
To avoid confusion, callbacks using ordinal pin numbers
is going to be reverted. So the driver has to be re-worked
to expose multiple devices so each device has 32 pins.
Also fixes#12765
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This allows the shared_irq driver to be configured by device tree.
With previous implementation, only the board configuration can
override the IRQ trigger, as the trigger config is a "choice" rather
than "config". With this patch, the driver can be fully configued at
the SoC level.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
PAE tables introduce the NX bit which is very desirable
from a security perspetive, back in 1995.
PAE tables are larger, but we are not targeting x86 memory
protection for RAM constrained devices.
Remove the old style 32-bit tables to make the x86 port
easier to maintain.
Renamed some verbosely named data structures, and fixed
incorrect number of entries for the page directory
pointer table.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Indicate that watchdog is supported on several Nordic DK boards
so that the wdt_nrfx driver is covered by CI builds.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Changes the default code location from internal itcm to external qspi or
hyperflash. Changes the default data location from internal dtcm to
external sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Changes the default code location from internal itcm to external qspi.
Changes the default data location from internal dtcm to external sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a new configuration option to mimxrt10{20,60,64}_evk boards to link
data into external sdram. The default remains to link data into internal
data tightly coupled memory (DTCM).
Note that mimxrt1050_evk is not included because it already has support
for linking data into sdram.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Unlinke nucleo or disco boards, ST-Link Tx/Rx pins used for Virtual
Com Port is not connected to the chip.
Then, console is not available by default and one should use a serial
cable to enjoy console. Adding mention of this fact to the board
documentation and replacing default hello_world example by blinky,
since blinky sample works without any additional hardware.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Somehow these were getting generated as `FLASH_foo_BLOCK_SIZE` even
though there's no specification for them in the original yaml. Put them
back until we can figure out what's going on.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
In #9717, 777407b9ea
coverage support was broken for all NATIVE_APPLICATION except
native_posix
This includes the nrf52_bsim board
Fix it.
Fixes: #13009
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The disco_l475_iot1 board should be using CONFIG_USB_DC_STM32 as the
Kconfig sybmol.
Also fix a minor typo in a comment in nucleo_f207zg with regards to
CONFIG_USB_DC_STM32
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
From the driver point of view, monochrome controllers from the ssd16xx
family mostly differ by the amount of row and columns that are
supported. If they support more than 256 rows and/or columns the
corresponding size or position is sent using 2 bytes instead of 1 byte.
This patch therefore adds the width-bits and height-bits DT properties
to make this configurable.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that stm32 watchdog should be configured by device tree,
update dts file of boards declaring watchdog support.
Additionally update doc and yaml files.
Add support on some boards that were used to validate the driver
update:
- disco_l475_iot1
- nucleo_f207zg
- nucleo_f429zi
- nucleo_f746zg
- nucleo_f073rz
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>